2018280--5 [TE]
Small Form- Factor Pluggable (SFP) Seating;型号: | 2018280--5 |
厂家: | TE CONNECTIVITY |
描述: | Small Form- Factor Pluggable (SFP) Seating |
文件: | 总4页 (文件大小:115K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
Small Form-Factor Pluggable (SFP)+ Seating
Tool Kits 2018280-[ ] for
Stacked PT Connector and Cage Assemblies
408-10261
10 NOV 11 Rev C
Seating Tool Kit 2018280 -1 Shown
Back
Seating Tool Bottomed
on Cage Assembly
2¢1 SFP+ Stacked PT
Connector and Cage
Assembly (With Gasket)
2007538-1 (Shown)
Wall Support
(For Clarity, Shown
Not Installed)
Press-Fit
Contact
SFP+ CONNECTOR
AND CAGE ASSEMBLY
CONFIGURATION
SEATING TOOL
KIT
2018280--1
2018280--2
2018280--3
2018280--4
2018280--5
2018280--6
2¢1
2¢2
2¢4
2¢6
2¢8
2¢5
Printed Circuit (PC)
Board (Ref)
PC Board Support
Fixture (Ref)
Figure 1
support must be installed into the port(s) of the cage
assembly.
1. INTRODUCTION
SFP+ Seating Tool Kits 2018280--[ ] are used to seat
the SFP+ stacked PT connector and cage assembly
configurations given in Figure 1 onto the pc board.
The connector and cage assemblies contain press--fit
contacts to allow solderless pc board installation.
Read these instructions thoroughly before using the
seating tool kit.
The top of the seating tool provides a surface to
accept the force applied by the application tool to seat
the connector and cage assembly onto the pc board.
During seating, the back and sides of the seating tool
protect the connector and cage assembly from
damage. The wall support supports the individual
port(s) of the cage assembly to prevent the cage
assembly from collapsing.
Dimensions on this sheet are in metric units [with
U.S. customary units in brackets]. Figures are not
drawn to scale.
NOTE
3. REQUIREMENTS
i
3.1. PC Board Support Fixture (Customer Supplied)
A pc board support must be used to provide proper
support for the pc board and to protect the pc board
and product from damage. The support fixture must
be designed for specific needs using the following
recommendations:
2. DESCRIPTION (See Figure 1)
Each seating tool kit consists of a seating tool and a
wall support. The seating tool and wall support are
also available separately. The seating tool has cutouts
(two located on each side) to accept the protruding
part of the standoffs of the cage assembly. The wall
S it should be at least 25.4 mm [1 in.] longer and
wider than the pc board.
E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change.
1 of 4
All Rights Reserved
PRODUCT INFORMATION 1--800--522--6752
For latest revision and Regional Customer Service,
visit our website at www.te.com
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks.
*Trademark. Other logos, product and/or Company names may be trademarks of their respective owners.
LOC B
408-10261
S it should have flat surfaces with holes or a
channel large enough and deep enough to
receive any protruding components of the
connector and cage assembly and to prevent
the pc board from bowing.
S the wall support must be properly installed, and
the seating tool, connector and cage assembly,
and application tool ram must be properly
aligned before cycling the application tool
1. Set tool seating height to the dimension shown
in Figure 2 (application tool shut height will equal
the tool seating height PLUS the combined
thicknesses of the pc board and support fixture).
After seating, a gap of no more than 0.10 mm
[.004 in.] between the cage assembly standoffs
and the pc board is allowed.
3.2. Application Tool
Power for seating tools must be provided by an
application tool (with a ram) capable of supplying a
downward force of 44.5 N [10 lb--force] per contact.
Manual Arbor Frame Assembly 58024--1 is available
for use with these seating tool kits. Refer to
Instruction Sheet 408--6923 for operating procedure.
Use the tool seating height as a reference
starting point. This height may need to be
adjusted to obtain the amount allowed (maximum
of 0.10 mm [.004 in.]) between the standoffs of
the cage assembly and the pc board.
NOTE
Over -driving of the connector and cage assembly
will deform parts critical to the quality of the
connection. Maximum force occurs prior to the
connector and cage assembly bottoming on the
pc board.
CAUTION
i
!
2. Slide the wall support into the port(s) of the cage
assembly until the wall support is secure.
4. SETUP
5. SEATING (Figure 2)
When setting up equipment to seat the connector and
cage assembly, pay particular attention to the
following:
1. Place the pc board on the support fixture.
2. Orient the seating tool over the cage assembly
so that the back is aligned with the back of the
cage assembly. Then lower the seating tool onto
the cage assembly, making sure that the cutouts
slide over the protruding components of the cage
assembly, until the seating tool bottoms on the top
of the cage assembly.
S the seating tool must be matched to the
connector and cage assembly
If the seating tool and connector and cage
assembly are mismatched or are improperly
aligned, damage could occur to the tooling,
connector and cage assembly, or both.
CAUTION
!
Note: Not to Scale
Ram of Application Tool
(Fully Down)
Seating Tool (2018280-1 Shown)
Cage Assembly
A
(See Table)
Wall Support (Installed in
Ports of Cage Assembly)
Application Tool
Shut Height
(Ram Fully Down)
(See Section 4, Step 1)
B
Press-Fit Contacts (and Any
Protruding Components) Inserted
into Holes in PC Board and
PC Board Support Fixture
(See Table)
0.10 mm [.004 in.]
(Max) Gap Allowed
PC Board
PC Board Support Fixture
DIMENSION A
TOOL SEATING HEIGHTD
DIMENSION B
CAGE ASSEMBLY SEATING HEIGHTD
40.64 mm [1.60 in.]
25.5 mm [1.004 in.]
D With Connector and Cage Assembly Seated
Figure 2
2 of 4
Rev C
408-10261
3. Place the connector and cage assembly on the
pc board so that the contacts and alignment posts
are aligned and started into the matching holes in
the pc board.
6.1. Daily Maintenance
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance.
4. Center the seating tool (with the connector and
cage assembly) under the ram of the application
tool. Slowly lower the ram until it just meets the
seating tool. Verify alignment of pc board support,
pc board, connector and cage assembly, and
seating tool.
1. Remove dust, moisture, and contaminants with
a clean, soft brush or a lint--free cloth. DO NOT
use objects that could damage the components.
2. When the seating tool and wall support are not
in use, store them in a clean, dry area.
Damage to the pc board, seating tool, or
connector and cage assembly may occur if the
seating tool is not properly seated on the
connector and cage assembly before cycling the
application tool.
CAUTION
6.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the seating tool or be supplied to
personnel responsible for the seating tool kit.
Inspection frequency should be based on amount of
use, working conditions, operator training and skill,
and established standards.
!
5. Cycle the application tool to seat the connector
and cage assembly on the pc board. Then retract
the ram, and carefully remove the seating tool by
pulling it straight from the cage assembly.
6. Remove the wall support from the cage
assembly.
7. REPLACEMENT AND REPAIR
Customer--replaceable parts are listed in Figure 3.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed
should be replaced by TE Connectivity to ensure
quality and reliability. Order replacement parts
through your representative, or call 1--800--526--5142,
or send a facsimile of your purchase order to
717--986--7605, or write to:
7. Check the connector and cage assembly for
proper seating according to the following:
a. the widest section of each compliant pin is
inside its intended pc board hole
b. each alignment post is in its intended pc
board hole
c. the connector and cage assembly is seated
on the pc board with a seating height—
measured from the top of the cage assembly
(not including the springs or elastomeric gasket)
to the top of the pc board— given in Figure 2
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105--3608
d. if present, the gap between the standoffs and
the pc board is no more than 0.10 mm [.004 in.]
8. REVISION SUMMARY
For detailed application requirements of the
connector and cage assembly, refer to the
relative application specification.
NOTE
S Updated document to corporate requirements
S Added new part numbers to tables in Figures 1
i
and 3
6. MAINTENANCE AND INSPECTION
The seating tool is assembled and inspected before
shipment. It is recommended that the seating tool be
inspected immediately upon arrival at your facility to
ensure that it has not been damaged during
shipment, and that it conforms to the dimensions
provided in Figure 3.
Rev C
3 of 4
408-10261
Seating Tool
(2¢4 Shown)
1
Wall Support
(2¢4 Shown)
2
A
E
F
D
B
C
REPLACEMENT PARTS
PART NUMBER FOR KIT (By Cage Assembly Configuration)
QTY PER
KIT
ITEM
2¢1
2¢2
2¢4
2¢6
2¢8
2¢ 5
1
2
2018296--1
2018289--1
2018295--1
2018286--1
2018294--1
2018284--1
2018297--1
2018292--1
2018798--1
2018801--1
2018802--1
2018805--1
1
1
KIT
DIMENSION (mm [in.])
(By Cage Assembly
Configuration)
A
B
C
D
E
F
2¢1
2¢2
2¢4
2¢6
2¢8
2¢5
17.93 [.706]
32.16 [1.266]
60.69 [2.389]
89.18 [3.511]
117.70 [4.634]
74.93 [2.950]
13.64 [.537]
27.89 [1.098]
56.39 [2.220]
84.89 [3.342]
113.28 [4.460]
70.61 [2.780]
59.00 [2.323]
32.38 [1.275]
Figure 3
50.80 [2.00]
24.26 [.955]
4 of 4
Rev C
相关型号:
©2020 ICPDF网 联系我们和版权申明