2215059-3 [TE]
Enhanced Small Form-Factor;型号: | 2215059-3 |
厂家: | TE CONNECTIVITY |
描述: | Enhanced Small Form-Factor |
文件: | 总4页 (文件大小:409K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Instruction Sheet
Enhanced Small Form-Factor
Pluggable (SFP+) Extraction Tool Kit
2215058-[ ] Cage Assemblies
408-32163
09 FEB 15 Rev A
Extraction Tool
Cutout (2 Plc)
Top Push Plate
Printed Circuit
(PC) Board (Ref)
Wall Supports
1 X 5 QSFP SFP+ Cage
Assembly 2284170-1
Finger Mounting Block
Base Plate
EXTRACTION TOOL
ENHANCED SFP+ CAGE ASSEMBLY CONFIGURATION
2215058-1
2215058-2
2215058-3
2215058-4
2215058-5
2215058-6
1 X 1
1 X 2
1 X 3
1 X 4
1 X 5
1 X 6
Figure 1
1. INTRODUCTION
Enhanced SFP+ Extraction Tool Kits 2215058-[ ] are used to remove the printed circuit (pc) board from
Enhanced SFP+ connector and cage assemblies described in Figure 1. The cage assemblies contain press-fit
contacts. Read these instructions thoroughly before using the extraction tool kit.
NOTE
Dimensions on this sheet are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for reference
only and are not drawn to scale.
2. DESCRIPTION
Each extraction tool kit consists of an extraction tool, a top push plate, base plate, and wall supports (one for
each stacked row of the cage assembly).
The base plate features a finger mounting block that holds up to six wall supports to the base plate. See
Figure 1. The top push plate is designed to be installed onto the upper tooling and the base plate is designed to
be installed onto the lower tooling of the application tool. The extraction tool has cutouts (one located on each
side) to accept the protruding part of the cage assembly. Each “finger” of a wall support fits into a port of the
cage assembly.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
© 2015 TE Connectivity family of companies
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
1 of 4
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
408-32163
During extraction, the back and sides of the extraction tool protect the cage assembly from damage, the wall
supports support the individual ports of the cage assembly, and the top push plate provides a surface to apply
an even force to extract the pc board from the connector and cage assembly.
3. APPLICATION TOOLING REQUIREMENT
Power for the extraction tool must be provided by application tools (with a ram) capable of supplying a
downward force of 44.5 N [10 lb] per contact.
Manual Arbor Frame Assembly 58024-1 is available for use with these extraction tool kits. Refer to Instruction
Sheet 408-6923 for operating procedure.
CAUTION
Over-driving of the extraction tool could cause damage to the connector or cage assembly.
4. EXTRACTION PROCEDURE
1. Ensure that the amount of wall supports installed onto the finger mounting block matches the amount
of ports of the cage assembly. It is recommended to center the group of wall supports on the finger
mounting block. Refer to Figure 1.
2. Install the top push plate onto the upper tooling and the base plate (with the wall supports) onto the
lower tooling of the application tool. See Figure 2.
CAUTION
Ensure that the upper tooling and lower tooling are secure; otherwise, damage to the connector and cage assembly could
occur.
3. Place the open end of the extraction tool over the cage assembly so that the cutouts align with the
protruding part (at the back) of the cage assembly. Make sure that the sides of the extraction tool sit
on the pc board.
4. Slide the extraction tool (with the connector and cage assembly and pc board) onto the wall supports
so that each “finger” of each wall support enters a port of the cage assembly. Make sure the fingers
are fully inserted into the ports. See Figure 2.
Side View
Application Tool Ram
Top Push Plate
Fingers of Wall
Supports Fully
Inserted into
Sides of Extraction Tool
Sitting on PC Board
Cage Assembly
PC Board
Base Plate (with
Wall Supports)
Lower Tooling of
Application Tooling
Figure 2
5. Cycle the application tool to extract the pc board from the connector and cage assembly. Then retract
the ram, and carefully remove the extraction tool (with the connector and cage assembly) from the
wall supports.
5. MAINTENANCE AND INSPECTION
The extraction tool kit is inspected before shipment. It is recommended that the extraction tool kit be inspected
immediately upon arrival at your facility to ensure that it has not been damaged during shipment and that it
conforms to the dimensions provided in Figure 3.
2 of 4
Rev A
408-32163
5.1. Daily Maintenance
It is recommended that each operator be made aware of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and contaminants with a clean, soft brush or a lint-free cloth. DO NOT use
objects that could damage the extraction tool kits components.
2. When the extraction tool kit is not in use, store it in a clean, dry area.
5.2. Periodic Inspection
Regular inspections should be performed by quality control personnel. A record of scheduled inspections
should remain with the extraction tool kit or be supplied to personnel responsible for the extraction tool kit.
Inspection frequency should be based on amount of use, working conditions, operator training and skill, and
established standards.
6. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 3. A complete inventory should be stocked and controlled to
prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by
TE Connectivity to ensure quality and reliability. Order replacement parts through your TE Representative, or
call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
7. REVISION SUMMARY
Initial release of document
1 X 4 Extraction Tool Kit Shown
2
A
40.4 [1.591]
1
40.00 [1.575]
5.72 [.225]
40.4 [1.591]
43.22 [1.702]
142.85 [5.624]
50.8 [2.00]
3
101.6 [4.00]
4
41.80 [1.646]
25.4 [1.00]
50.8 [2.00]
5
Figure 3 (cont’d)
3 of 4
Rev A
408-32163
TOOL (BY KIT PART NUMBER)
2215058-1
DIMENSION “A”
19.45 [.766]
2215058-2
33.70 [1.327]
47.95 [1.888]
62.20 [2.449]
76.45 [3.010]
90.70 [3.571]
2215058-3
2215058-4
2215058-5
2215058-6
QTY PER TOOL
1 X 3 1 X 4
ITEM
NUMBER
DESCRIPTION
1 X 1
1 X 2
1 X 5
1 X 6
TOOL,
1
1
1
1
1
1
1
Extraction
PLATE, Top
Push
2
3
4
1
1
1
2
1
1
3
1
1
4
1
1
5
1
1
6
PLATE, Base
1
1
SUPPORT,
Wall
MOUNTING
BLOCK, Finger
5
1
1
1
1
1
1
EXTRACTION TOOL KIT PART NUMBER
ITEM NUMBER
2215058-1
2215058-2
2215058-3
2215058-4
2215058-5
2215058-6
1
2
3
4
5
2215059-1
2215059-2
2215059-3
2215059-4
2215059-5
2215059-6
211356-1
2161354-1
2215638-1
2215637-1
Figure 3 (end)
4 of 4
Rev A
相关型号:
©2020 ICPDF网 联系我们和版权申明