2215875-5

更新时间:2024-10-29 21:54:38
品牌:TE
描述:Small Form-Factor Pluggable

2215875-5 概述

Small Form-Factor Pluggable

2215875-5 数据手册

通过下载2215875-5数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。

PDF下载
Instruction Sheet  
Small Form-Factor Pluggable (SFP+ with  
External EMI Springs, Heat Sink) Surface  
Mount Cage Assembly Seating Tool 2215084-[ ]  
408-32215  
10 DEC 15 Rev A  
Back of  
Seating Tool  
1 X 1 Seating Tool  
(Bottomed on Cage Assembly)  
1 X 1 Cage  
Assembly  
1 X 1 Wall Support  
(For Clarity, Not  
Shown Installed)  
Compliant Pin  
Contact  
Printed Circuit  
(PC) Board (Ref)  
PC Board Support  
Fixture (Ref)  
SFP+ CAGE  
ASSEMBLY  
CONFIGURATION  
SEATING  
TOOL KIT  
APPLICATION  
SPECIFICATION  
2215084-1  
2215084-2  
2215084-3  
1 X 1  
1 X 1  
1 X 1  
NOTE: Connector Not Shown  
114-13120  
Figure 1  
1. INTRODUCTION  
SFP+ surface mount PT connector and cage assembly seating tool kits listed in Figure 1 are used to seat the  
cage assemblies described in Figure 1 onto the pc board. The cage assembly contains compliant pin contacts  
to allow solderless pc board installation. The seating tool is not designed to seat the connector.  
Read these instructions thoroughly before using the seating tool kit.  
NOTE  
Dimensions on this sheet are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for reference  
only and are not drawn to scale.  
2. DESCRIPTION (Figure 1)  
Each seating tool kit consists of a seating tool and a wall support. The seating tool and wall support are also  
available separately. The seating tool has cutouts (two located on each side) to accept the protruding part of  
the standoffs of the cage assembly. The wall support must be installed into the ports of the cage assembly.  
The top of the seating tool provides a surface to accept the force applied by the application tool to seat the  
product onto the pc board. During seating, the back and sides of the seating tool protect the cage assembly  
from damage. The wall support supports the individual ports of the cage assembly.  
This controlled document is subject to change.  
For latest revision and Regional Customer Service,  
visit our website at www.te.com.  
© 2015 TE Connectivity family of companies  
All Rights Reserved  
*Trademark  
PRODUCT INFORMATION 1-800-522-6752  
1 of 4  
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.  
408-32215  
3. REQUIREMENTS  
3.1. PC Board Support Fixture (Customer Supplied)  
A pc board support must be used to provide proper support for the pc board and to protect the pc board and  
the connector and cage assembly from damage. The support fixture must be designed for specific needs using  
the following recommendations:  
it should be at least 25.4 mm [1 in.] longer and wider than the pc board  
it should have flat surfaces with holes or a channel large enough and deep enough to receive any  
protruding components of the product  
3.2. Application Tool  
Power for seating tools must be provided by an application tool (with a ram) capable of supplying a downward  
force of 44.5 N [10 lb-force] per contact. For available application tools, call PRODUCT INFORMATION at the  
number at the bottom of page 1.  
CAUTION  
Over-driving of the cage assembly will deform parts critical to the quality of the connection. Maximum force occurs prior to the  
cage assembly bottoming on the pc board.  
4. SETUP  
When setting up equipment to seat the cage assembly, pay particular attention to the following:  
the seating tool must be matched to the cage assembly  
CAUTION  
If the seating tool and cage assembly are mismatched or are improperly aligned, damage could occur to the tooling, cage  
assembly, or both.  
light pipes MUST NOT be assembled onto the cage assembly  
the wall support must be properly installed, and the seating tool, cage assembly, and application tool ram  
must be properly aligned before cycling the application tool  
1. Set the tool seating height to the dimension shown in Figure 2 (application tool shut height will equal  
the tool seating height PLUS the combined thicknesses of the pc board and support fixture).  
Ram of Application  
Tool (Fully Down)  
Seating Tool  
Tool Seating Height  
Wall Support (Installed in  
(With Cage  
Ports of Cage Assembly  
Assembly Seated)  
Compliant Pin Contacts (and Any  
Protruding Components) Inserted into  
Application Tool  
Shut Height  
(Ram Fully Down)  
(See Section 4,  
0.10 [.004] (Max)  
Holes in PC Board and PC Board  
Gap Allowed  
Support Fixture  
Step 1)  
PC Board  
PC Board  
Support Fixture  
Figure 2  
After seating, a gap of no more than 0.10 mm [.004 in.] between the cage assembly standoffs and the  
pc board is allowed.  
NOTE  
Use the tool seating height as a reference starting point. This height may need to be adjusted to obtain the amount allowed  
(maximum of 0.10 mm [.004 in.]) between the standoffs of the cage assembly and the pc board.  
2 of 4  
Rev A  
408-32215  
2. Slide the wall support into the ports of the cage assembly until the wall support is secure.  
5. SEATING (Figure 2)  
NOTE  
The connector must be mounted on the pc board BEFORE seating the cage assembly.  
1. Place the pc board on the support fixture.  
2. Orient the seating tool over the cage assembly so that the back is aligned with the back of the cage  
assembly. Then lower the seating tool onto the cage assembly, making sure that the cutouts slide  
over the protruding components of the cage assembly, until the seating tool bottoms on the top of the  
cage assembly.  
3. Place the cage assembly on the pc board so that the contacts and alignment posts are aligned and  
started into the matching holes in the pc board.  
4. Center the seating tool (with the cage assembly) under the ram of the application tool. Slowly lower  
the ram until it just meets the seating tool. Verify alignment of pc board support, pc board, cage  
assembly, and seating tool.  
CAUTION  
Damage to the pc board, seating tool, or cage assembly may occur if the seating tool is not properly seated on the cage  
assembly before cycling the application tool.  
5. Cycle the application tool to seat the cage assembly on the pc board. Then retract the ram, and  
carefully remove the seating tool by pulling it straight from the cage assembly.  
6. Check the cage assembly for proper seating according to the following:  
a. the widest section of each compliant pin is inside its intended pc board hole  
b. each alignment post is in its intended pc board hole  
c. if present, the gap between the standoffs and the pc board is no more than 0.10 mm [.004 in.]  
NOTE  
For detailed application requirements of the cage assembly, refer to the application specification given in Figure 1.  
6. MAINTENANCE AND INSPECTION  
The seating tool kit is assembled and inspected before shipment. It is recommended that the seating tool kit be  
inspected immediately upon arrival at your facility to ensure that it has not been damaged during shipment, and  
that it conforms to the dimensions provided in Figure 3.  
6.1. Daily Maintenance  
It is recommended that each operator be made aware of, and responsible for, the following steps of daily  
maintenance:  
1. Remove dust, moisture, and contaminants with a clean, soft brush or a lint-free cloth. DO NOT use  
objects that could damage the components.  
2. When the seating tool and wall support are not in use, store them in a clean, dry area.  
6.2. Periodic Inspection  
Regular inspections should be performed by quality control personnel. A record of scheduled inspections  
should remain with the seating tool or be supplied to personnel responsible for the seating tool kit. Inspection  
frequency should be based on amount of use, working conditions, operator training and skill, and established  
standards.  
7. REPLACEMENT AND REPAIR  
Customer-replaceable parts are listed in Figure 3. Parts other than those listed should be replaced by TE to  
ensure quality and reliability. For customer repair service or to order replacement parts, call 1-800-522-6752, or  
fax your purchase order to 717-986-7605, or write to: Customer Service (038-035), Tyco Electronics  
Corporation, PO Box 3608, Harrisburg, PA 17105-3608.  
3 of 4  
Rev A  
408-32215  
8. REVISION SUMMARY  
Initial release of document  
Seating Tool 2215084-1  
3
Top  
1
F
B
G
E
6
A
2
Side  
Front  
4
5
C
SEATING TOOL  
KIT (BY CAGE  
ASSEMBLY  
DIMENSION  
A
B
C
E
F
G
CONFIGURATION)  
2215084-1  
2215084-2  
2215084-3  
18.0 [.71]  
18.0 [.71]  
18.0 [.71]  
44.0 [1.73]  
44.0 [1.73]  
44.0 [1.73]  
25.0 [.98]  
27.3 [1.07]  
34.2 [1.35]  
13.3 [.52]  
13.3 [.52]  
13.3 [.52]  
8.4 [.33]  
8.4 [.33]  
8.4 [.33]  
50.8 [2.00]  
50.8 [2.00]  
50.8 [2.00]  
REPLACEMENT PARTS  
DESCRIPTION  
QTY PER KIT  
ITEM NUMBER  
PART NUMBER  
2215084-1  
2215084-2  
2215084-3  
1
2
2215818-4  
2215872-1  
2215875-1  
2215875-4  
2215875-5  
2215874-1  
2215874-2  
2215874-3  
2215873-1  
2215873-2  
2215873-3  
18024-2  
Wall Support  
Center Block  
1
1
1
1
1
1
1
3
4
Rear Plate  
1
1
1
1
1
1
6
Left Side Plate  
Right Side Plate  
5
6
1
6
1
6
Screw, Btn. Head Cap  
Figure 3  
4 of 4  
Rev A  

2215875-5 相关器件

型号 制造商 描述 价格 文档
2215876-1 TE Small Form-Factor Pluggable 获取价格
2215877-1 TE Small Form-Factor Pluggable 获取价格
2215877-2 TE Small Form-Factor Pluggable 获取价格
2215878-1 TE Small Form-Factor Pluggable 获取价格
2215878-2 TE Small Form-Factor Pluggable 获取价格
2215879-1 TE Small Form-Factor Pluggable 获取价格
2215879-2 TE Small Form-Factor Pluggable 获取价格
2215880-1 TE Small Form-Factor Pluggable 获取价格
2215880-2 TE Small Form-Factor Pluggable 获取价格
2215881-1 TE Small Form-Factor Pluggable 获取价格

2215875-5 相关文章

  • HARTING(浩亭)圆形连接器产品选型手册
    2024-10-31
    6
  • HYCON(宏康科技)产品选型手册
    2024-10-31
    6
  • GREEGOO整流二极管和晶闸管产品选型手册
    2024-10-31
    7
  • 西门子豪掷106亿美元,战略收购工程软件巨头Altair
    2024-10-31
    8