305183 [TE]

Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools;


型号：	305183
厂家：	TE CONNECTIVITY
描述：	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools 工具和机器连接器连接器支架
文件：	总2页 (文件大小：91K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Instruction Sheet

Extraction Tools 305183,

305183-4, -6, -7, -8, and -13

408-1216

03 MAY 11 Rev D

PROPER USE GUIDELINES

Cumulative Trauma Disorders can resultfrom the prolonged use ofmanually powered hand tools. Hand tools are intended for occasional use and low volume

applications. A wide selection of powered application equipment for extended-use, production operations is available.

Plastic

and Steel

Tool

with all other components made of steel. The second

style illustrated in Figure 1 has an aluminum push rod

button with all other components made of steel. The

part number determines the style of the tool.

Sleeve

3. EXTRACTION PROCEDURE

Handle

Refer to Figure 1, and select the appropriate

extraction tool according to the contact type and

contact size, to be removed. Proceed as follows:

Push Rod Button

Aluminum

and Steel

Tool

1. For smaller wire, use Insertion Tool 91002--1 to

“unseat” the contact retention spring from the

housing contact cavity retention ledge by exerting

a small amount of force on the back of the contact.

For larger wire with sufficient column strength,

push on the contact wire.

CONTACT

TYPE

EXTRACTION

TOOL

SIZE

II, III, III(+), VI, X, and

Subminiature Coaxial

2. Align the sleeve of the tool with the contact to

be removed. See Figure 2.

305183-- 0

All Sizes

305183--4

305183--6

305183--7

3. Holding the tool handle, insert the sleeve

straight into the contact cavity until it bottoms. To

determine if the extraction tool is fully seated on

the housing retention ledge; thereby ensuring that

the retention tines are fully retracted, a mark can

be placed on the tool sleeve when it comes to rest

on the retention ledge of an empty housing contact

cavity. Allow the push rod button to “back out” of

the handle as shown in Figure 3.

305183--8

Miniature Coaxial

1--305183--3-- 0

D Plastic and Steel — All Others: Aluminum and Steel

Figure 1

Pin Contact

(Ref)

1. INTRODUCTION

The extraction tools listed in Figure 1 are designed to

remove pin and socket contacts from Multimate

connectors. Read these instructions thoroughly

before starting.

Sleeve

Dimensions on this instruction sheet are in

millimeters [with inch equivalents in brackets].

Illustrations are for identification only and are not

drawn to scale.

NOTE

Figure 2

Reasons for reissue of this instruction sheet are

provided in Section 6, REVISION SUMMARY.

Rotate Handle

Depress

Push Rod

Button

2. DESCRIPTION

Each tool features a handle and sleeve to release the

contact locking lance, and a push rod button to eject

the contact.

Sleeve Bottomed

in Cavity

There are two styles of tools. The first style illustrated

in Figure 1 has a plastic handle and push rod button

Figure 3

E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company

*Trademark

TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change.

1 of 2

PRODUCT INFORMATION 1--800--522--6752

For latest revision and Regional Customer Service,

visit our website at www.te.com

LOC B

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

408-1216

4. Rotate the tool handle to ensure contact locking

lance has released.

Store the tool in a clean, dry place. Clean the tool with

a soft, lint--free cloth.

5. Keep the tool sleeve firmly bottomed in the

contact cavity, and depress the push rod button.

The contact will eject as the button is depressed.

5. REPLACEMENT AND REPAIR

The tool is not repairable and should be replaced

when worn or damaged.

If the contact becomes lodged in the contact

cavity and excessive force must be used to

extract the contact, verify that all of the contact

retention tines are still attached to the contact

after removal and have not been embedded in

the contact cavity.

NOTE

Order tools through your representative, or call

1--800--526--5142, or send a facsimile of your

purchase order to 717--986--7605, or write to:

CUSTOMER SERVICE (038--035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

6. Remove the tool from the contact cavity.

HARRISBURG PA 17105--3608

4. MAINTENANCE AND INSPECTION

6. REVISION SUMMARY

To ensure proper operation, it is recommended that

the tool be inspected immediately on arrival and at

regularly scheduled intervals.

Revisions to this instruction sheet include:

S Changed company logo

Plastic and Steel

Tool

Aluminum and Steel

Tool

DIMENSION

EXTRACTION

TOOL

305183-- 0

305183--4

305183--6

305183--7

305183--8

2.92 [.115]

4.11 [.162]

5.77 [.227]

6.50 [.256]

5.18 [.204]

5.77 [.227]

3.28 [.129]

4.55 [.179]

6.38 [.251]

7.21 [.284]

5.69 [.224]

6.17 [.243]

30.73 [1.21]

25.65 [1.01]

29.21 [1.15]

25.65 [1.01]

115.06 [4.53]

104.90 [4.13]

112.01 [4.41]

104.90 [4.13]

81.28 [3.20]{

71.88 [2.83]

79.76 [3.14]

71.88 [2.83]

1--305183--3-- 0

{This dimension was 76.2 [3.00] prior to tool Rev R.

Figure 4

2 of 2

Rev D

相关型号：