7024NCB [TE]

Industrial Electropneumatic Timing Relay; 工业电子气动定时继电器


型号：	7024NCB
厂家：	TE CONNECTIVITY
描述：	Industrial Electropneumatic Timing Relay 工业电子气动定时继电器继电器电子
文件：	总6页 (文件大小：360K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Catalog 1308242

Issued 3-03 (PDF Rev. 10-07)

AGASTAT

7000 series

Industrial Electropneumatic

Timing Relay

File E15631

File LR29186

Note:7032 types and certain models with accessories are not agency approved.

Users should thoroughly review the technical data before selecting a product

part number. It is recommended that users also seek out the pertinent

approvals files of the agencies/laboratories and review them to confirm the

product meets the requirements for a given application.

Consult factory for ordering information.

Design Features

On-delay model 7012 (delay on pickup)

• Available in on-delay, true off-delay, and on/off-delay.

Applying continuous voltage to the coil

(L1-L2) starts a time delay lasting for

the preset time. During this period the

normally closed contacts (3-5 and 4-6)

remain closed. At the end of the delay

period the normally closed contacts

break and the normally open contacts

(1-5 and 2-6) make. The contacts re-

main in this transferred position until

the coil is deenergized, at which time

the switch instantaneously returns to

its original position.

De-energizing the coil, either during

or after the delay period, will recycle

the unit within 50 msec.

It will then provide a full delay period

upon re-energization, regardless of

how often the coil voltage is interrupt-

ed before the unit has been permitted

to "time-out" to its full delay setting.

• Timing from 0.1 seconds to 60 minutes, in linear increments.

• Oversize time-calibrated adjustment knobs, serrated with high-resolution

markings visible from all angles makes the timer easy to set timers.

• Inherent transient immunity.

• Standard voltages from 6-550VAC and 12-550VDC (special voltages available.)

• Available in 2-pole or 4-pole models.

• Numerous enclosure options: explosion proof, dust tight, watertight,

hermetically-sealed, NEMA 1.

• Auxiliary timed and instantaneous switches can be added for greater switching

flexibility.

• Many mounting options: Surface mount, Panel mount, Octal plug-in mounting.

• Options: quick-connect terminals, dial stops, and transient protection module.

• Easy-to-reach screw terminals, all on the face of the unit, clearly identified.

• Modular assembly - timing head, coil assembly and switchblock are all

individual modules, with switches field-replaceable.

Design & Construction

There are three main components of Series 7000 Timing Relays:

Calibrated Timing Head uses no needle valve, recirculates air under

controlled pressure through a variable orifice to provide linearly adjustable

timing. Patented design provides instant recycling, easy adjustment and long

service life under severe operating conditions.

Off-delay model 7022 (delay on dropout)

Applying voltage to the coil (for at

least 50 msec) will instantaneously

transfer the switch, breaking the nor-

mally closed contacts (1-5 and 2-6),

and making the normally open

contacts (3-5 and 4-6). Contacts

remain in this transferred position as

long as the coil is energized. The

time delay begins immediately upon

de-energization. At the end of the de-

lay period the switch returns to its

normal position.

Re-energizing the coil during the

delay period will immediately return

the timing mechanism to a point

where it will provide a full delay

period upon subsequent de-

Precision-Wound Potted Coil module supplies the initial motive force

with minimum current drain. Total sealing without external leads eliminates

moisture problems, gives maximum insulation value.

Snap-Action Switch Assembly

- custom-designed over-center

mechanism provides greater contact pressure up to transfer time for

positive, no flutter action. Standard switches are DPDT arrangement, with

flexible beryllium copper blades and silver-cadmium oxide contacts. Special

"timing-duty" design assures positive wiping action, sustained contact pres-

sure and greater heat dissipation during long delay periods.

Each of these subassemblies forms a self-contained module which is

then assembled at the factory with the other two to afford a wide choice of

operating types, coil voltages, and timing ranges.

The squared design with front terminals and rear mounting permits the

grouping of Series 7000 units side-by-side in minimum panel space.

Auxiliary switches may be added in the base of the unit, without affecting

the overall width or depth.

energization. The switch remains in

the transferred position.

Operation

Two basic operating types are available.

To increase the versatility of the basic timer models, auxiliary switches may

be added to either on-delay or off-delay types. They switch additional circuits,

provide two-step timing action, or furnish electrical interlock for sustained coil

energization from a momentary impulse, depending on the type selected and

its adjustment. Because of their simple attachment and adjustment features,

they can be installed at the factory or in the field, by any competent mechanic.

All auxiliary switches are SPDT with UL listings of 10A @ 125, 250, or 480

VAC. A maximum of one Code T or two Code L auxiliary switches may be

added to each relay. The L or LL switch is available with on-delay relays only.

The T switch is available with both the on-delay and off-delay relays.

Auxiliary Switch Options for On-Delay

“On-Delay” models provide a delay period on energization, at the end of

which the switch transfers the load from one set of contacts to another. De-

energizing the unit during the delay period immediately recycles the unit,

readying it for another full delay period on re-energization.

In "Off-Delay" models the switch transfers the load immediately upon

energization, and the delay period does not begin until the unit is de-

energized. At the end of the delay period the switch returns to its original po-

sition. Re-energizing the unit during the delay period immediately resets the

timing, readying it for another full delay period on de-energization. No power

is required during the timing period.

In addition to these basic operating types, "Double-Head" models offer

sequential delays on pull-in and drop-out in one unit. With the addition of

auxiliary switches the basic models provide two-step timing, pulse actuation

for interlock circuits, or added circuit capacity.

Instant Transfer (Auxiliary Switch Code L,

maximum of 2 per relay.)

1. Energizing coil begins time delay and transfers auxiliary switch.

2. Main switch transfers after total preset delay.

3. De-energizing coil resets both switches instantly.

Auxiliary switch is nonadjustable.

NOTE: Seismic & radiation tested E7000 models are available.

Consult factory for detailed information.

Two-Step Timing (Auxiliary Switch Code T,

maximum of 1 per relay.)

Dimensions are shown for

reference purposes only.

Dimensions are in inches over

(millimeters) unless otherwise

specified.

Specifications and availability

subject to change.

www.tycoelectronics.com

Technical support:

Refer to inside back cover.

1248

Catalog 1308242

Issued 3-03 (PDF Rev. 10-07)

AGASTAT

Auxiliary switch options

To increase the versatility of the basic timer models, auxiliary switches may

be added to either on-delay or off-delay types. They switch additional circuits,

provide two-step timing action, or furnish electrical interlock for sustained coil

energization from a momentary impulse, depending on the type selected and

its adjustment. Because of their simple attachment and adjustment features,

they can be installed at the factory or in the field, by any competent mechanic.

All auxiliary switches are SPDT with UL listings of 10A @ 125, 250, or 480 VAC.

A maximum of one Code T or two Code L auxiliary switches may be added to

each relay. The L or LL switch is available with on-delay relays only. The T

switch is available with both the on-delay and off-delay relays.

Auxiliary Switch Options for On-Delay

Instant Transfer (Auxiliary Switch Code L, maximum of 2 per relay.)

1. Energizing coil begins time delay and transfers auxiliary switch.

2. Main switch transfers after total preset delay.

3. De-energizing coil resets both switches instantly.

Auxiliary switch is nonadjustable.

4. De-energizing coil resets both switches instantly. First delay is

independently adjustable, up to 30% of overall delay.

(Recommended maximum 100 seconds.)

Auxiliary Switch Options for Off-Delay

In these models the same auxiliary switch provides either two-step timing or

instant transfer action, depending on the adjustment of the actuator.

Two-Step Timing (Auxiliary Switch Code T, maximum of 1 per relay.)

1. Energizing coil transfers main and auxiliary switches instantly.

2. De-energizing coil begins time delay.

3. After first delay auxiliary switch transfers.

4. Main switch transfers after total preset delay. First delay is independently

adjustable, up to 30% of overall delay. (Recommended maximum 100 sec-

onds.)

Instant Transfer (Auxiliary Switch Code L, maximum of 1 per relay.)

1. Energizing coil transfers main and auxiliary switches instantly.

2. De-energizing coil resets auxiliary switch and begins time delay.

3. Main switch transfers after total preset delay.

Auxiliary switch is factory adjusted to give instant transfer operation, but may

be easily adjusted in the field to provide two-step timing.

Two-Step Timing (Auxiliary Switch Code T, maximum of 1 per relay.)

1. Energizing coil begins time delay.

2. After first delay auxiliary switch transfers.

3. Main switch transfers after total preset delay.

On-delay, off-delay model 7032 (double head)

The Double Head model provides delayed switch transfer on

energization of its coil, followed by delayed resetting upon coil de-

energization. Each delay period is independently adjustable.

In new circuit designs or the improvement of existing controls now

using two or more conventional timers, the Double Head unit offers distinct

advantages.

Its compact design saves precious panel space, while the simplified

wiring reduces costly interconnection.

Four pole model 7014. 7024

With the addition of an extra switch block at the bottom of the basic unit,

this version of the Series 7000 offers four pole switch capacity with simul-

taneous timing or two-step timing. The two-step operation is achieved by

factory adjustment to your specifications.

For two-step operation, a maximum timing ratio between upper and

lower switches of 3:2 is recommended. Once adjusted at the factory, this

ratio remains constant regardless of changes in dial settings. (Ex: If upper

switch transfer is set on dial at 60 sec., minimum time on lower switch

should be 40 sec.)

This Series 7000 unit offers many of the performance features found in

basic models - voltage ranges, timing and switch capacities are virtually iden-

tical.

Four pole models add approximately 1-1/4" to the maximum height of the

basic model, approximately 1/8" to the depth. They are designed for vertical

operation only.

Surge/transient protection option

Features

The Surge/Transient Protection Option protects electronic control circuits from

transients and surges which are generated when the timer coil is activated.

Built with a minimum of moving parts, the unit provides a fast response to rap-

idly rising voltage transients. The accurate, precision-made device is not polari-

ty sensitive and permits the user to initiate, delay, sequence and program

equipment actions over a wide range of applications under the most severe

operating conditions.

It consists of a specially modified coil case, varistor, varistor cover, terminal

extensions and cup washers so that normal terminations can be used. The

varistor will not affect the operating characteristics of the 7000 Timer. The

varistor has bilateral and symmetrical voltage and current characteristics and

therefore can be used in place of the back-to-back zener diodes. This charac-

teristic also means that the coil will not be polarity sensitive.

• Protect electronic control circuits

from voltage transients generated

by the timer coil.

• Fast response to the rapidly rising

back E.M.F.

• High performance clamping voltage

characteristics.

• UL recognized, (except varistor and

coil together).

• Timer NOT polarity sensitive.

Transient Suppressor

Option "V"

Dimensions are shown for

reference purposes only.

Dimensions are in inches over

(millimeters) unless otherwise

specified.

Specifications and availability

subject to change.

www.tycoelectronics.com

Technical support:

Refer to inside back cover.

1249

Catalog 1308242

Issued 3-03 (PDF Rev. 10-07)

AGASTAT

Timing Specifications (All values shown are at nominal voltage and 25°C unless otherwise specified).

Operating Modes:

Minimum operating voltages are based on vertically mounted 7012 units.

Model 7012/7014: On-delay (delay on pick-up).

7012 horizontally mounted or 7022 vertically or horizontally mounted units

will operate satisfactorily at minimum voltages approximately 5% lower than

those listed.

Model 7022/7024: Off-delay (delay on drop-out).

Model 7032: On-delay, off-delay (double head).

Timing Adjustment: Timing is set by simply turning the dial to the desired

time value. In the zone of approximately 25° separating the high and low

end of timing ranges A,D,E, and K, instantaneous operation (no time delay)

will occur. All other ranges produce an infinite time delay when the dial is

set in this zone.

AC units drop out at approximately 50% of rated voltage. DC units drop out

at approximately 10% of rated voltage.

All units may be operated on intermittent duty cycles at voltages 10% above

the listed maximums (intermittent duty - maximum 50% duty cycle and 30

minutes "on" time.)

Models 7014 and 7032 are available with letter-calibrated dials only. The

upper end of the time ranges in these models may be twice the values

shown.

Surge/Transient Protection Option Characteristics (DC Timers Only)

Coil Voltage

Nominal (DC)

Max Excess

Energy Capacity (Joule)

Max De-energization

Transient Voltage

Linear Timing Ranges:

Models 7012,

7022, 7024

Models 7014,

7032

Code

.1 to 1 Sec.

.2 to 2 Sec.

.7 to 7 Sec.

2 to 20 Sec.

10 to 100 Sec.

30 to 300 Sec.

1.5 to 15 Min.

3 to 30 Min.

Not Avail.

12 V

24 V

28 V

32 V

48 V

60 V

96 V

110 V

125 V

220 V

250 V

0.4 J

1.8 J

2.5 J

3.57 J

6 J

10 J

17 J

48 V

.5 to 5 Sec.

93 V

1.5 to 15 Sec

5 to 50 Sec.

20 to 200 Sec.

1 to 10 Min.

3 to 30 Min.

6 to 60 Min.

3 to 120 Cyc.

1 to 300 Sec.

93 V

135 V

145 V

250 V

340 V

366 V

Not Avail.

Repeat Accuracy:

For delays of 200 seconds or less:

7012*, 7022, 7024:

7014*:

7032:

+5%

+10%

+15%

Surge Life

Applied 100,000 times continuously with the interval of 10 seconds at room

temperature. Below 68 VAC: 12A; Above 68 VAC: 35A

Temperature Range

For delays greater than 200 seconds: 7012*, 7022, 7014*, 7024: +10%

7032: +15%

* The first time delay afforded by Model 7012 with H (3 to 30 min.) and I (6

to 60 min.) time ranges or Model 7014 with H time range will be approx.

15% longer than subsequent delays due to coil temperature rise.

Reset Time: 50 msec. (except model 7032)

Operating: -22°F to +167°F (-30°C to + 75°C)

Storage: -40°F to +167°F (-40°C to +75°C)

Output/Life Contact Ratings: Contact Capacity in Amps (Resistive Load)

Contact

Min. 100,000 Min. 1,000,000

Relay Release Time: 50 msec. for on-delay models (7012/7014)

Relay Operate Time: 50 msec. for off-delay models (7022/7024)

Voltage

Operations

15.0

Operations

7.0

30 VDC

110 VDC

120 V 60Hz

240 V 60Hz

480 V 60Hz

1.0

0.5

20.0

15.0

Operating Voltage Coil Data (for DPDT)

12.0

10.0

Operating*

Voltage

Range

Operating

Voltage

Range

10 Amps Resistive, 240 VAC

Coil

Code

Rated

Voltage

1/4 Horsepower, 120 VAC/240VAC (per pole)

Part # Letter Voltage

15 Amps 30 VDC (per pole)

@ 60Hz

@50Hz

5 Amps, General Purpose, 600VAC (per pole)

7000

120

240

480

550

102-132

204-264

408-528

468-605

20.5-26.5

110

220

93.5-121

187-242

Dielectric: Withstands 1500 volts RMS 60Hz between terminals and

ground. 1,000 volts RMS 60 Hz between non-connected terminals. For

dielectric specification on hermetically sealed models consult factory.

Insulation Resistance: 500 Megohms with 500VDC applied.

Temperature Range: Operating: -20°F to +165°F (-29°C to 74°C)

Storage: -67°F to +165°F (-55°C to 74°C)

Temperature Variation: Using a fixed time delay which was set and

measured when the ambient temperature was 77°F (25°C), the maximum

observed shift in the average of three consecutive time delays was -20% at

-20°F (-29°C) and +20% at 165°F (74°C).

Mounting/Terminals: Normal mounting of the basic unit is in a vertical

position, from the back of the panel. A front mounting bracket is also

supplied with each basic unit, for installation from the front of the panel.

All units are calibrated for vertical operation. Basic models (7012, 7022)

may also be horizontally mounted, and will be adjusted accordingly when

Accessory Y1 is specified in your order.

Standard screw terminals (8-32 truss head screws supplied) are located

on the front of the unit, with permanent schematic markings. Barrier

isolation is designed to accommodate spade or ring tongue terminals, with

spacing to meet all industrial control specifications.

The basic Series 7000 may also be panel mounted with the addition of a

panelmount kit that includes all necessary hardware and faceplate. This

offers the convenience of "out-front" adjustment, with large calibrated dial

skirt knob. The faceplate and knob blend with advanced equipment and

console designs, while the body of the unit and its wiring are protected

behind the panel.

Other mounting options include plug-in styles and special configurations

to meet unusual installation requirements. Contact factory for details.

Power Consumption: Approximately 8 watts power at rated voltage .

Approximate Weights:

127

240

108-140

204-264

208

10.2-13.2

5.1-6.6

178-229

Dual Voltage Coil

(Combines A&B)

Special AC Coils

(L1, L2, etc.)

7010

22.4-30.8

38.4-52.8

19.2-26.4

100-137.5

9.6-13.2

125

48-66

250

550

200-275

440-605

12.8-17.6

25.8-35.2

76.8-105.6

4.8-6.6

220

176-242

Special DC Coils

(X1, X2, etc.)

*Four pole Models: Operational voltage range 90% to 110% for AC units;

85% to 110% for DC units.

Models

7012, 7022 . . . . . . . 2 lbs. 4 ozs.

7014, 7024 . . . . . . . 2 lbs. 10 ozs.

7032 . . . . . . . . . . . . 3 lbs. 5 ozs.

Weight may vary slightly with coil voltage.

See next column for more coil data.

Dimensions are shown for

reference purposes only.

Dimensions are in inches over

(millimeters) unless otherwise

specified.

Specifications and availability

subject to change.

www.tycoelectronics.com

Technical support:

Refer to inside back cover.

1250

Catalog 1308242

Issued 3-03 (PDF Rev. 10-07)

AGASTAT

Outline Dimensions (Dimensions in inches).

Model 7032

Models 7012, 7022

Models 7014, 7024

Panel mount Option "X"

Surge/Transient Protection Option

Dimensions are shown for

reference purposes only.

Dimensions are in inches over

(millimeters) unless otherwise

specified.

Specifications and availability

subject to change.

www.tycoelectronics.com

Technical support:

Refer to inside back cover.

1251

Catalog 1308242

Issued 3-03 (PDF Rev. 10-07)

AGASTAT

Ordering Information

Typical Part No. ꢀ

1. Basic Series:

70 = 7000 series electropneumatic timing relay

2. Operation:

1 = On-delay

2 = Off-delay

3 = On-delay, off-delay (double head)

3. Contact Arrangement:

2 = 2PDT (2 form C)

**4 = 4PDT (4 form C)

4. Coil Voltage:

AC Coils

DC Coils

A = 120VAC, 60 Hz.; 110VAC, 50Hz.

B = 240VAC, 60 Hz.; 220VAC, 50Hz.

C = 480VAC, 60 Hz.

M = 28VDC

N = 48VDC

O = 24VDC

P = 125VDC

Q = 12VDC

R = 60VDC

D = 550VAC, 60 Hz.

E = 24VAC, 60 Hz.

F = 127VAC, 50 Hz.

G = 240VAC, 50Hz.

S = 250VDC

T = 550VDC

U = 16VDC

H = 12VAC, 60 Hz.

K = Dual voltage (combines A & B)

L = Special AC coils (L1, L2, etc.)

V = 32VDC

W = 96VDC

Y = 6VDC

Z = 220VDC

X = Special DC coils (X1, X2, etc.)

5. Timing Range:

Models 7012, 7022 & 7024

A = .1 to 1 sec.

†Models 7014 & 7032

For model 7032 specify separate time

range code for each head. Example: AB.

Any two ranges may be selected.

A = .2 to 2 sec.

B = .5 to 5 sec.

C = 1.5 to 15 sec.

D = 5 to 50 sec.

E = 20 to 200 sec.

F = 1 to 10 min.

H = 3 to 30 min.

I = 6 to 60 min.

B = .7 to 7 sec.

C = 2 to 20 sec.

D = 10 to 100 sec.

E = 30 to 300 sec.

J = 3 to 120 cyc.

K = 1 to 300 sec.

F = 1.5 to 15 min.

H = 3 to 30 min.

6. Options:

A1 = Single quick-connect terminals (note 4).

K = Explosion-proof Enclosure (note 1).

L = Auxiliary Switch, instant transfer. 7012 only (notes 2 & 6).

LL = Two Aux. Switches, instant transfer. On Model 7014 Factory Installed Only. (notes 2 & 6)

M = Dust-tight Gasketing (notes 4 & 5).

A2 = Double quick-connect terminals (note 4).

B = Plug-in connectors (note 4).

GZ = Enclosure with bottom knockouts (note 1).

H2 = Hermetically sealed enclosure, 8 pin solder (notes 1 & 4).

H3 = Hermetically sealed enclosure, 8 pin octal (notes 1 & 4).

H4 = Hermetically sealed enclosure, 8 screw terminal block (notes 1 & 4).

*H6 = Hermetically sealed enclosure, 11 pin solder (notes 1 & 4).

*H7 = Hermetically sealed enclosure, 11 pin octal (notes 1 & 4).

*H8 = Hermetically sealed enclosure, 11 screw terminal block (notes 1 & 4).

l1 = Tamper-proof Cap, opaque black (Cannot be combined with Option X).

l2 = Tamper-proof Cap, transparent (Cannot be combined with Option X).

P = Octal Plug Adapter. Can be combined only with options l1,l2. M, S, X, or Y1. (note 4).

S = Dial Stops.

T = Auxiliary Switch, two-step timing (notes 2 & 6).

V = Transient/Surge Protection (for DC coil voltage only).

W = Watertight Enclosure (note 1).

X = Panelmount includes hardware and adjustment for horizontal operation (note 4)

Y1 = Horizontal calibration, for horizontal operation without panelmounting (note 4).

Y2 = Horizontal calibration, with Compensating Spring for vertical operation (note 4).

Notes:

1. Cannot be combined with B, P or X Options

2. Cannot be combined with B, P or Y2 Options

3. Cannot be combined with GZ, H, l1, l2, K, W or Y1 Options

4. Not Avail. on 4-Pole Models

5. Not Available with L, T or LL options.

6. Not Available on hermetically sealed units.

Sized to accommodate one L or T Auxiliary Switch

** Not available on On-Delay, Off-Delay (Double Head) model.

Available with letter calibrated dials only. Upper end of time range may be twice the value shown

†† 120 cycles = 2 sec.

†

Our authorized distributors are more likely to maintain the following items in stock for immediate delivery..

7012AA

7012AB

7012AC

7012AD

7012AE

7012AF

7012AH

7012AK

7012ACL

7012BC

7012NC

7012PA

7012PB

7012PC

7012PD

7012PF

7012PJ

7012PK

7012PKX

7012PJX

7022AA

7022AB

7022AC

7022AD

7022AE

7022AF

7022AH

7022AI

7022AJ

7022AKT

7022BC

7022BK

7022PA

7022PB

7022PC

7022PK

Dimensions are shown for

reference purposes only.

Dimensions are in inches over

(millimeters) unless otherwise

specified.

Specifications and availability

subject to change.

www.tycoelectronics.com

Technical support:

Refer to inside back cover.

1252

Catalog 1308242

Issued 3-03 (PDF Rev. 10-07)

AGASTAT

Ordering options – can only be orderd as factory installed options (Dimensions, where shown, are in inches.)

A1 – Single Quick-Connect Terminals

A2 – Double Quick-Connect Terminals

B – Plug-In Connectors

Use with Accessory

“C” or “D” below.

GZ – Total Enclosure

With knockouts for bottom

connection.

H – Hermetically Sealed Enclosure

I – Tamper-Proof Cover

3.16" W x 3.84" D x 7.63"H

K – Explosion proof Enclosure

L – Auxiliary Switch

LL – Auxiliary Switch

(Meets requirements for

Class I, Groups C&D

locations).

7.50"W x 6.00" D x 10.38" H

M – Dustight

P – Octal Plug Adapter

S – Dial Stops

Gasket

V – Transient/Surge Protection

W – Watertight Enclosure (NEMA-4)

T – Auxiliary Switch

4.75" W x 4.44" D x 9.75" H

Transient

Protection

X – Panelmount Kit

Mounting hardware

included.

Accessories (Not available for 7032 models)

Plug-In Receptacle (Accessory D)

Plug-In Receptacle (Accessory C)

Screw Terminals Catalog

No. 700137. For use with

"B" Option

Quick Connect

Terminals

Catalog No. 700141.

For use with "B"

Option.

Ordering options can only be ordered as factory installed options.

Dimensions are shown for

reference purposes only.

Dimensions are in inches over

(millimeters) unless otherwise

specified.

Specifications and availability

subject to change.

www.tycoelectronics.com

Technical support:

Refer to inside back cover.

1253

7024NCB [TE]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E