MA03501D [TE]

X-Band Gain/Phase Control MMIC 8.0 -11.0 GHz; X波段增益/相位控制MMIC 8.0 -11.0 GHz的


型号：	MA03501D
厂家：	TE CONNECTIVITY
描述：	X-Band Gain/Phase Control MMIC 8.0 -11.0 GHz X波段增益/相位控制MMIC 8.0 -11.0 GHz的
文件：	总7页 (文件大小：438K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

RO-P-DS-3004 - -

X-Band Gain/Phase Control MMIC

8.0 –11.0 GHz

Features

8.0-11.0 GHz Serial Input Control MMIC

♦ 8.0 to 11.0 GHz Operation

♦ 6-bit Phase Shifter and 5-bit Attenuator

♦ Serial Control Input

♦ 50 Ω Input and Output Impedance

♦ Self-Aligned MSAG^®MESFET Process

Primary Applications

♦ Radar Systems

Description

The MA03501D is a serial control input phase shifter/

attenuator/buffer amplifier MMIC. The on-chip serial to

parallel converter circuitry allows for control of the 6

phase and 5 attenuation bits using a single TTL/CMOS

compatable input. This product is fully matched to 50

ohms on both the input and output.

Each device is 100% RF tested on wafer to ensure

performance compliance. The part is fabricated using

M/A-COM’s repeatable, high performance and highly

reliable GaAs Multifunction Self-Aligned Gate (MSAG^®)

MESFET Process.

Electrical Characteristics: T_B= 25°C¹, Z₀= 50Ω, V_DD= 5V, V_GG= -4V, V_EE= -4.0

Parameter

Symbol

Minimum

Typical

Maximum

Units

Bandwidth

8.0

11.0

GHz

Gain

1-dB Compression Point

Input Return Loss

P1dB

IRL

22.5

dBm

Output Return Loss

ORL

Attenuation Range (5-bits, 0.75dB step)

RMS Attenuation Error (Uncorrected)

0.75 dB Attenuator Bit

1.5 dB Attenuator Bit

0.2

0.8

1.5

3.0

6.0

0.5

1.0

2.0

3 dB Attenuator Bit

2.4

3.6

6 dB Attenuator Bit

5.0

7.0

12 dB Attenuator Bit

10.8

13.2

1. T_B= MMIC Base Temperature

RO-P-DS-3004 - - 2/7

X-Band Serial Input Gain/Phase Control MMIC

MA03501D

Electrical Characteristics: T_B= 25°C, Z₀= 50Ω, V_DD= 5V, V_GG= -4V, V_EE= -4.0

Parameter

Symbol

Minimum

Typical

Maximum

Units

Phase Shift Range (6 bits, 5.6 degree step)

354

Deg

RMS Phase Error (Uncorrected)

5.6 Degree Bit

5.3

Deg

4.0

8.0

7.0

11.25 Degree Bit

11.0

22.0

44.0

90.0

180

+/-1.0

13.0

24.0

47.0

95.0

190

22.5 Degree Bit

19.0

40.0

85.0

170

45 Degree Bit

90 Degree Bit

180 Degree Bit

Gain Variation over all Phase Shifter settings

Output Third Order Intercept Point

Noise Figure

OTOI

dBm

Drain Supply Current

I_DD

160

275

500

Gate Supply Current

I_GG

Digital Power Supply Current

Input Logic High Current

Input Logic Low Current

Timing Delay-Enable Signal to Bit Change

I_EE

0.5

0.1

Absolute Maximum Conditions ¹

Parameter

Input Power

Symbol

Absolute Maximum

Units

8.0

dBm

P_IN

V_DD

V_GG

I_DQ

Drain Supply Voltage

Gate Supply Voltage

-6.0

Quiescent Drain Current (No RF)

Quiescent DC Power Dissipated (No RF)

Digital Power Supply Voltage

Junction Temperature

500

2.5

P_DISS

V_EE

T_j

-6.0

180

°C

Storage Temperature

T_STG

-55 to +150

1. Operation outside of these ranges may reduce product reliability. Operation at other than the typical values may

result in performance outside the guaranteed limits.

Specifications subject to change without notice.

Customer Service: Tel. (888)563-3949

Email: macom_adbu_ics@tycoelectronics.com

North America: Tel. (800) 366-2266

Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298

Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020

V 1.00

Visit www.macom.com for additional data sheets and product information.

RO-P-DS-3004 - - 3/7

X-Band Serial Input Gain/Phase Control MMIC

Recommended Operating Conditions

MA03501D

Characteristic

Symbol

Min

Typ

Max

Unit

Drain Voltage

V_DD

4.0

5.0

6.0

Gate Voltage

V_GG

V_EE

V_IH

V_IL

-4.5

-4.2

3.0

-4.0

3.5

0.0

-3.5

-3.8

5.0

Digital Power Supply Voltage

Input Logic High Voltage

Input Logic Low Voltage

Clock Frequency

0.0

0.4

F_CLK

T_J

MHz

ºC

Junction Temperature

MMIC Base Temperature

150

T_B

Note 2

2. Maximum MMIC Base Temperature = 150°C— 31.8°C/W * V_DD* I_DQ

Operating Instructions

This device is static sensitive. Please handle

with care. To operate the device, follow these

steps.

1. Apply V_GG= -4 V, V_EE= -4V, V_DD= 0 V.

2. Ramp V_DDto desired voltage, typically 5 V.

3. Adjust V_GGto set I_DQ, (approximately @ –4V).

4. Set RF input.

5. Power down in reverse. Turn gate voltage off

last.

Specifications subject to change without notice.

Customer Service: Tel. (888)563-3949

Email: macom_adbu_ics@tycoelectronics.com

North America: Tel. (800) 366-2266

Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298

Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020

V 1.00

Visit www.macom.com for additional data sheets and product information.

RO-P-DS-3004 - - 4/7

X-Band Serial Input Gain/Phase Control MMIC

Typical Small Signal Characteristics (V_DD=5V, V_GG=-4V)

MA03501D

22.0

21.0

20.0

19.0

18.0

17.0

16.0

15.0

14.0

8.0

8.5

9.0

9.5

10.0

10.5

11.0

Frequency (GHz)

Figure 1. Gain

-10.0

-12.0

-14.0

-16.0

-18.0

-20.0

-22.0

-24.0

S22:

S11:

8.0

8.5

9.0

9.5

10.0

10.5

11.0

Frequency (GHz)

Figure 2. Input and Output Match

Specifications subject to change without notice.

Customer Service: Tel. (888)563-3949

Email: macom_adbu_ics@tycoelectronics.com

North America: Tel. (800) 366-2266

Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298

Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020

V 1.00

Visit www.macom.com for additional data sheets and product information.

RO-P-DS-3004 - - 5/7

X-Band Serial Input Gain/Phase Control MMIC

MA03501D

0.45

0.40

0.35

0.30

0.25

0.20

0.15

0.10

0.05

0.00

8.0

8.5

9.0

9.5

10.0

10.5

11.0

Frequency (GHz)

Figure 3. RMS Attenuation Error

4.5

4.0

3.5

3.0

2.5

2.0

1.5

1.0

0.5

0.0

8.0

8.5

9.0

9.5

10.0

10.5

11.0

Frequency (GHz)

Figure 4. RMS Phase Error

Specifications subject to change without notice.

Customer Service: Tel. (888)563-3949

Email: macom_adbu_ics@tycoelectronics.com

North America: Tel. (800) 366-2266

Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298

Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020

V 1.00

Visit www.macom.com for additional data sheets and product information.

RO-P-DS-3004 - - 6/7

X-Band Serial Input Gain/Phase Control MMIC

Mechanical Information

MA03501D

Chip Size: 5.974 x 3.973 x 0.075 mm (236 x 157 x 3 mils)

3.973mm.

3.820mm.

V_GG

3.222mm.

V_EE

2.485mm.

2.186mm.

1.886mm.

1.586mm.

1.287mm.

GND

V_DD

0.751mm.

OUT

0.150mm.

Bond Pad Dimensions

Pad

Size (mils)

6 x 6

Size (µm)

150 x 150

RF In and Out

DC Supply Voltages

DC Control Voltages

6 x 6

Specifications subject to change without notice.

Customer Service: Tel. (888)563-3949

Email: macom_adbu_ics@tycoelectronics.com

North America: Tel. (800) 366-2266

Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298

Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020

V 1.00

Visit www.macom.com for additional data sheets and product information.

RO-P-DS-3004 - - 7/7

X-Band Serial Input Gain/Phase Control MMIC

Assembly and Bonding Diagram

MA03501D

100 pF

V_GG

V_DD

0.1 µF

RF_OUT

RF_IN

DATA

V_EE

100 pF

0.1 µF

Figure 5. Recommended bonding diagram.

Support circuitry typical of MMIC characterization fixture for CW testing.

Assembly Instructions:

Die attach: Use AuSn (80/20) 1-2 mil. preform solder. Limit time @ 300 °C to less than 5 minutes.

Wirebonding: Bond @ 160 °C using standard ball or thermal compression wedge bond techniques. For

DC pad connections, use either ball or wedge bonds. For best RF performance, use wedge bonds of

shortest length, although ball bonds are also acceptable.

Biasing Note: Must apply negative bias to V_GGbefore applying positive bias to V_DDto prevent

damage to amplifier.

Specifications subject to change without notice.

Customer Service: Tel. (888)563-3949

Email: macom_adbu_ics@tycoelectronics.com

North America: Tel. (800) 366-2266

Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298

Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020

V 1.00

Visit www.macom.com for additional data sheets and product information.

相关型号：