MAAM-011168-TR1000 [TE]
Differential CATV Variable Gain Amplifier;型号: | MAAM-011168-TR1000 |
厂家: | TE CONNECTIVITY |
描述: | Differential CATV Variable Gain Amplifier 有线电视 |
文件: | 总16页 (文件大小:1914K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Features
Functional Schematic
40 dB Gain
15.5 dB, 0.5 dB steps, 5 Bit Digital Step
Attenuator
48
37
36
1
CMOS Control
36 dB MER, 64 QAM 39 Channels, 52 dBmV/ch.
8 V Operation
2.6 dB Noise Figure
Serial or Parallel Attenuator Control
Differential Input and Output
Low Harmonics
34
33
7
8
30
29
Power Down Mode
Lead-Free 7 mm 48-lead PQFN Package
Halogen-Free “Green” Mold Compound
RoHS* Compliant
26
25
12
13 14
17 18
24
Description
Pin Configuration3
The MAAM-011168 is an integrated 2 stage
differential amplifier with embedded digital step
attenuator (DSA) assembled in a lead-free 7 mm
48-lead PQFN package.
Pin
Pin
No.
Description
No.
Description
1
6
Latch Enable
30
Stage 2 Output (+)
The module provides excellent linearity and high
output power with greater than 30 dB MER for
64 QAM modulation with 39 channels and 52 dBmV
per channel. Gain in the minimum attenuation state
is typically 40 dB. The internal DSA offers 15.5 dB
attenuation range with 0.5 dB steps. The device is
optimized for high output power with 8 V bias and
can also operate from 5 V bias if lower DC power
consumption and output level is desired. The
module also provides a power down function for
each of the amplifier stages.
Stage1 Feedback (+) 32 Stage 2 Feedback(+)
7
Stage 1 input (+)
Stage 1 input (-)
33
Stage 2 Input (+)
8
34 Attenuator Output (+)
9
Stage 1 Feedback(-) 36
DSA Serial Output
Power Up Select 2
Power Up Select 1
13
14
15
Stage 1 Output (+)
Stage 1 Output (-)
Enable Stage 1
37
38
39 VDD CMOS Controller
16 Stage 1 Bias Voltage 40 Unused Control (B5)5
17 Attenuator Input (-) 41 Attenuator Bit 4 (8 dB)
18 Attenuator Input (+) 42 Attenuator Bit 3 (4 dB)
20 Stage 2 Bias Voltage 43 Attenuator Bit 2 (2 dB)
This amplifier is ideally suited for use in CATV
reverse path applications.
21
Enable Stage 2
44 Attenuator Bit 1 (1 dB)
Ordering Information1,2
25 Attenuator Output (-) 45 Attenuator Bit 0 (0.5 dB)
Part Number
Package
26
Stage 2 Input (-)
46
Parallel/Serial Select
Clock
MAAM-011168-TR1000
MAAM-011168-TR3000
1000 piece reel
3000 piece reel
27 Stage 2 Feedback(-) 47
29
Stage 2 Output (-)
48
49
Serial Input
RF and DC Ground4
MAAM-011168-001SMB
Sample Test Board
3. All pins not listed in the table are “No Connection” and should
be left unconnected.
4. The exposed pad centered on the package bottom must be
connected to RF and DC ground.
1. Reference Application Note M513 for reel size information.
2. All sample boards include 5 loose parts.
5. MACOM recommends grounding pin 40. It is connected to the
CMOS controller but does not affect attenuator setting.
* Restrictions on Hazardous Substances, European Union
Directive 2011/65/EU.
1
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Electrical Specifications: TA = +25°C, VCC = 8 V, minimum attenuation state, Z0 = 75 Ω
Parameter
Gain
Test Conditions
Units
dB
Min.
38
Typ.
40
Max.
42
Max. Gain State @ 100 MHz, -29 dBm PIN
Gain Slope
Positive tilt from 5 - 200 MHz
dB
—
1.0
2.6
22
—
Noise Figure6
Input Return Loss
Output Return Loss
Reverse Isolation
Attenuation Range
—
dB
—
—
—
dB
—
—
—
dB
—
22
—
—
dB
—
50
—
100 MHz, Relative to maximum gain, -29 dBm PIN
dB
14.6
15.5
16.4
39 Channels (5 - 250 MHz), 51 dBmV/Ch.
Single Channel (8 - 200 MHz), 71 dBmV/Ch.
Single Channel (250 MHz), 70 dBmV/Ch.
16 Channels (5 - 250 MHz), 56 dBmV/Ch.
—
—
—
30
36
35
35
34
64 QAM
dB
—
Modulated Error Ratio7
P1dB
OIP2
—
dBm
dBm
dBm
ns
—
—
—
—
—
—
—
27
74
—
—
2-tone,+9 dBm/tone, 1 MHz tone spacing, 200 MHz
2-tone,+9 dBm/tone, 1 MHz tone spacing, 200 MHz
50% Control to 90 / 10 % RF
EN1 = EN2 = 5 V
OIP3
44
—
TON, TOFF
ICC
400
290
3
—
mA
315
10
—
ICC_OFF
EN1 = EN2 = 0 V
mA
IEN1, IEN2
EN1 = EN2 = 5 V
mA
0.7
6. Includes Balun loss
7. Modulation error ratio each channel 64 QAM 5.12 MS/s
2
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Truth Table12
Absolute Maximum Ratings8,9,10
Parameter
RF Input Power
Bias Voltage (VCC
Control Voltage
Absolute Maximum
-8 dBm
B5
X
B4
1
B3
1
B2
1
B1
1
B0 Attenuation (dB)
1
0
1
1
1
1
0
Minimum
)
10 V
X
1
1
1
1
0.5
1
-0.5 V to 5.5 V
-40°C to +100°C
+150°C
X
1
1
1
0
Operating Temperature
Junction Temperature11
Storage Temperature
X
1
1
0
1
2
X
1
0
1
1
4
-65°C to +150°C
X
0
1
1
1
8
8. Exceeding any one or combination of these limits may cause
permanent damage to this device.
X
0
0
0
0
15.5
9. MACOM does not recommend sustained operation near
these survivability limits.
12. Logic “0” = 0 V to 0.8 V ± 0.2 V,
Logic “1” = 2 V to 5 V ± 0.2 V.
10. Operating at nominal conditions with TJ ≤ 150°C will ensure
MTTF > 1 x 106 hours.
11. Junction Temperature (TJ) = TC + Өjc * (V * I)
Typical thermal resistance (Өjc) = 8.85° CW.
a) For TC = +25°C,
TJ = 47°C @ 8 V, 315 mA
b) For TC = +100°C,
TJ = 122°C @ 8 V, 315 mA
3
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
PCB Layout
Application Schematic
B5
2
3
4
5
1
1
3
5
4
2
4
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Parts List : 8 V Application circuit
Part
Value
0.1 µF
0.1 µF
150 pF
1 µF
Case Style
0402
0402
0402
0805
0402
0806
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
0402
Function/Notes
RF Bypass
C1, C9, C20, C21, C22, C23, C24, C29
C2, C4, C5, C7, C8, C11, C12, C13, C14
C15, C17, C18, C27, C28
DC Block
C3, C19
C25
Gain Tilt (with R16 and R17)
Low Frequency Bypass
Output Match
C26
1 pF
L1, L12
L2, L11
L3, L10
L4, L9
47 µH
250 nH
22 nH
22 nH
27 nH
33 nH
0 Ω
VCC1 Choke. Murata LQH2MCN470K02L
Gain Tilt (with R7 & R14). Coilcraft 0402AF-251XJLU
Input Match Stage2 Amp
Output Match Stage1 Amp
L5, L8
Input Match Stage1 Amp
L6, L7
Output Match Stage2 Amp
R1
Input Match
R18
30 Ω
Increase value can reduce stage 2 current
Voltage divider to set VDD_CMOS13
Voltage divider to set VDD_CMOS13
Gain Tilt (with L2, L11)
R2
3 kΩ
R4
5 kΩ
R7, R14
R16, R17
R8
249 Ω
22 Ω
Gain Tilt (with C3, C19)
10 kΩ
50 Ω
Increase value can reduce stage 1 current.
Drop VCC1 to 5 V. Pdiss 1/20 W. 0 Ω for 5 V VCC
R10, R11, R21, R22
Additional feedback resistors for Stage1 & Stage2.
May be used to adjust gain or implement temperature
compensation if replaced with thermistors.
0402 or
0603
R5, R6, R19, R20
T1, T2
150 Ω
1:2
MABA-011050
13. These components may be omitted if 5 V supply is available for VDD_CMOS.
5
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Typical Performance Curves:
Gain
Gain - Wideband
Output Return Loss
Input Return Loss
Reverse Isolation
Noise Figure
6
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Typical Performance Curves:
OIP3, OIP2
Gain
Modulation Error Ratio (64 QAM, 16 channel)
Modulation Error Ratio (64 QAM, single channel)
Modulation Error Ratio (64 QAM, 32 channel)
POUT @ 30 dB Modulation Error Ratio
75
50
45
40
70
65
60
55
50
35
FC = 14 MHz
30
FC = 32 MHz
FC = 56 MHz
FC = 104 MHz
25
FC = 146 MHz
FC = 194 MHz
20
0
8
16
24
32
40
30
35
40
45
50
55
60
Output Power (dBmV)
Number of 64 QAM Channels
7
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Lead-Free 7 mm 48-lead PQFN
†
Reference Application Note S2083 for lead-free solder reflow recommendations.
Meets JEDEC moisture sensitivity level 3 requirements.
Plating is NiPdAuAg.
Recommended Land Pattern
Handling Procedures
Please observe the following precautions to avoid
damage:
0.508 mm
0.254 mm
0.3 mm
0.2 mm
0.8 mm
Static Sensitivity
0.305 mm
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
HBM Class 1B devices.
0.432 mm
7.8 mm
0.864 mm
5.8 mm
0.2 mm
Copper plating (board and vias) should be ≥ 0.05 mm thick.
8
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Applications Section
First Stage Bypass Application
If a lower gain VGA solution is desired the MAAM-011168 may be implemented with the first stage bypassed.
Typical Performance and Application Details for implementing the First Stage Bypass Application are presented
below.
Typical Performance: TA = +25°C, VCC = 8 V, minimum attenuation state, Z0 = 75 Ω
Parameter
Gain
Test Conditions
Units
dB
Typical
19
Max. Gain State @ 100 MHz, -29 dBm PIN
Gain Slope
Positive tilt from 5 - 250 MHz
dB
0
Input Return Loss
Output Return Loss
Noise Figure
—
dB
22
—
dB
22
—
dB
4.3
Attenuation Range
100 MHz, Relative to maximum gain, -29 dBm PIN
dB
15.5
39 Channels (5 - 250 MHz), 51 dBmV/Ch.
Single Channel (8 - 200 MHz), 71 dBmV/Ch.
Single Channel (250 MHz), 70 dBmV/Ch.
16 Channels (5 - 250 MHz), 56 dBmV/Ch.
36
35
35
34
64 QAM MER7
dB
P1dB
OIP2
OIP3
ICC
—
dBm
dBm
dBm
mA
27
76
2-tone,12 dBm/tone, 1 MHz tone spacing, 200 MHz
2-tone,12 dBm/tone, 1 MHz tone spacing, 200 MHz
EN1 = EN2 = 5 V
46
225
9
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
PCB Layout: First Stage Bypass
Application Schematic: First Stage Bypass
1
5
4
2
3
1
4
3
2
5
10
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Parts List : First Stage Bypass
Part
Value
0.1 µF
0.1 µF
470 pF
1 µF
Case Style
0402
0402
0402
0805
0402
0402
-
Function/Notes
RF Bypass
C9, C13, C21, C22, C23, C28
C2, C4, C5, C15, C17, C18
DC Block
C14
C25
Gain Flatness
Low Frequency Bypass
Input, Output Matching
Gain Flatness
C27, C29
C26
1pF
270 pF
DNI
C7
Matching if needed
L3, L10
L4, L9
L6, L7
L11, L12
R18
18 nH
22 nH
24 nH
120 nH
30 Ω
0402
0402
0402
0402
0402
0402
0402
0402
0402
Input Match Stage2 Amp
Input Match DSA
Output Match Stage2 Amp
Gain Flatness
Increase value can reduce stage 2 current
Gain Flatness
R19, R20
R2
6.8 Ω
3 kΩ
Voltage divider to set VDD_CMOS13
Voltage divider to set VDD_CMOS13
Gain Flatness
R4
5 kΩ
R16, R17
100 Ω
Additional feedback resistors for Stage1 & Stage2. May be
R5, R6
T1, T2
150 Ω
0402 or 0603 used to adjust gain or implement temperature compen-
sation if replaced with thermistors.
1:2
MABA-011050
11
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Typical Performance Curves: First Stage Bypass Application
Gain
Noise Figure
Output Return Loss
Input Return Loss
OIP3, OIP2
MER vs Pout - 16 Channels
12
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Functionality
Modes of Operation: Serial, Direct Parallel, and Latched Parallel
Mode Truth Table
P/S
1
LE
X
Mode
Serial
0
Constant High
Pulsed
Direct Parallel
Latched Parallel
0
Serial Mode
The serial control interface (SERIN, CLK, LE, SEROUT) is compatible with the SPI protocol. SPI mode is
activated when P/S is kept high. The 6-bit serial word must be loaded with MSB first. After shifting in the 6 bit
word, bringing LE high will set the attenuator to the desired state. While LE is high the CLK is masked to protect
the data while implementing the change . SEROUT is the SERIN delayed by 6 clock cycles.
When P/S is low, the serial control interface is disabled and the serial input register is loaded asynchronously with
parallel digital inputs.
Direct Parallel Mode
The parallel mode is enabled when P/S is set to low. In the direct parallel mode, the attenuator is controlled by the
parallel control inputs directly. The LE must be at logic high to control the attenuator in this mode.
Latched Parallel Mode
In the latched parallel mode, the parallel control inputs will be buffered by registers, and loaded to the outputs
when LE is high. The outputs shall not change states when LE is low.
Power-up States
The power-up (PUP) states will work in both serial and parallel modes, and initiate the attenuator according to the
PUP truth table. During power up, the digital inputs shall be held constant for at least 1 μs after VCC reaches 90%
of final value. For serial mode, the PUP states will only work when LE is held low. The PUP state shall be locked
out after the first LE pulse. Proper operation of power up states requires fast rise time (<200 ns) for VDD-CMOS.
13
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Functionality
Modes of Operation: Serial, Direct Parallel, and Latched Parallel
PUP Truth Table
Inputs
Gain Relative to Max. Gain
Notes
PS
0
LE
0
PUP2
PUP1
0
0
1
1
X
X
X
0
1
0
1
X
X
X
-15.5 dB
0
0
-8 dB
0 dB
0
0
Parallel Mode
Serial Mode
0
0
0 dB
0
1
0 to –15.5 dB (Set B0 - B4)
0 to –15.5 dB (Set B0 - B4)
No Definition
1
0
1
1
Serial Interface Timing Characteristics
Typical Performance
+25°C
Symbol
Parameter
Units
-40°C
100
20
+85°C
100
20
tSCK
tCS
Min. Serial Clock Period
Min. Control Set-up Time
Min. Control Hold Time
Min. LE Set-up Time
100
20
ns
ns
ns
ns
ns
ns
ns
tCH
20
20
20
tLS
10
10
10
tLEW
tLH
Min. LE Pulse Width
10
10
10
Min. Serial Clock Hold Time from LE
Min. LE Pulse Spacing
10
10
10
tLES
630
630
630
14
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
Functionality
Modes of Operation: Serial, Direct Parallel, and Latched Parallel
Serial Input Interface Timing Diagram
tLS tLEW tLH
SERIAL
CLK
LE
tLES
D5
MSB
D0
LSB
CONTROL
WORD
D4
D1
tCS
tCH
Parallel Control Word
tLEW
LE
tLS
tLH
30ns Minimum
15
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAAM-011168
Differential CATV Variable Gain Amplifier
5 - 300 MHz
Rev. V2
M/A-COM Technology Solutions Inc. All rights reserved.
Information in this document is provided in connection with M/A-COM Technology Solutions Inc ("MACOM")
products. These materials are provided by MACOM as a service to its customers and may be used for
informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or
in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM
assumes no responsibility for errors or omissions in these materials. MACOM may make changes to
specifications and product descriptions at any time, without notice. MACOM makes no commitment to update
the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future
changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise,
to any intellectual property rights is granted by this document.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR
INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR
OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY
OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN
THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS,
WHICH MAY RESULT FROM THE USE OF THESE MATERIALS.
MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM
customers using or selling MACOM products for use in such applications do so at their own risk and agree to
fully indemnify MACOM for any damages resulting from such improper use or sale.
16
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
相关型号:
©2020 ICPDF网 联系我们和版权申明