74ACT11139PWRE4 [TI]
ACT SERIES, OTHER DECODER/DRIVER, INVERTED OUTPUT, PDSO16, GREEN, PLASTIC, TSSOP-16;
| 型号： | 74ACT11139PWRE4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | ACT SERIES, OTHER DECODER/DRIVER, INVERTED OUTPUT, PDSO16, GREEN, PLASTIC, TSSOP-16 驱动 光电二极管 输出元件 逻辑集成电路 |
| 文件： | 总15页 (文件大小：886K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ꢀ ꢁ ꢂꢃ ꢄꢅꢅꢅꢆ ꢇ
ꢈꢉꢂ ꢊ ꢋ ꢌꢊ ꢍꢎꢏ ꢄ ꢐ ꢁ ꢌꢊ ꢍꢎꢏ ꢈꢏꢃ ꢐꢈ ꢏꢑꢒ ꢈꢏꢓ ꢉꢊꢄꢍ ꢔ ꢊꢏ ꢕꢏ ꢑ
SCAS175A − SEPTEMBER 1991 − REVISED APRIL 1996
D, N, OR PW PACKAGE
(TOP VIEW)
D
D
Inputs Are TTL-Voltage Compatible
Designed Specifically for High-Speed
Memory Decoders and Data Transmission
Systems
1
2
3
4
5
6
7
8
16
15
14
13
12
1Y0
1A
1B
1Y1
1Y2
1Y3
GND
2Y0
2Y1
2Y2
2Y3
D
Incorporates Two Enable Inputs to Simplify
Cascading and/or Data Reception
1G
D
Fully Synchronous Operation for Counting
V
CC
11 2G
10 2A
D
Center-Pin V
Minimize High-Speed Switching Noise
and GND Configurations
CC
9
2B
D
D
D
EPIC (Enhanced-Performance Implanted
CMOS) 1-µm Process
500-mA Typical Latch-Up Immunity at
125°C
Package Options Include Plastic
Small-Outline (D) and Thin Shrink
Small-Outline (PW) Packages, and
Standard Plastic 300-mil DIPs (N)
description
The 74ACT11139 is designed for use in high-performance memory-decoding or data-routing applications that
require very short propagation delay times. In high-performance memory systems, this decoder is used to
minimize the effects of system decoding.
The 74ACT11139 is composed of two individual 2-line to 4-line decoders in a single package. The active-low
enables (1G or 2G) can be used as data lines in demultiplexing applications. This decoder/demultiplexer
features fully buffered inputs, each of which represents only one normalized load to its driving circuit.
The 74ACT11139 is characterized for operation from −40°C to 85°C.
FUNCTION TABLE
INPUTS
OUTPUTS
G
H
L
B
X
L
A
X
L
Y0
H
L
Y1
H
H
L
Y2
H
H
H
L
Y3
H
H
H
H
L
L
L
H
L
H
H
H
L
H
H
H
H
L
H
H
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
EPIC is a trademark of Texas Instruments Incorporated.
ꢔꢑ ꢐ ꢈꢉ ꢃ ꢄꢍ ꢐ ꢎ ꢈ ꢂꢄꢂ ꢖꢗ ꢘ ꢙꢚ ꢛ ꢜꢝ ꢖꢙꢗ ꢖꢞ ꢟꢠ ꢚ ꢚ ꢡꢗꢝ ꢜꢞ ꢙꢘ ꢢꢠꢣ ꢤꢖꢟ ꢜꢝ ꢖꢙꢗ ꢥꢜ ꢝꢡ ꢦ
ꢔꢚ ꢙ ꢥꢠꢟ ꢝ ꢞ ꢟ ꢙꢗ ꢘꢙ ꢚ ꢛ ꢝ ꢙ ꢞ ꢢꢡ ꢟ ꢖꢘ ꢖꢟꢜ ꢝꢖ ꢙꢗꢞ ꢢꢡ ꢚ ꢝꢧ ꢡ ꢝꢡ ꢚ ꢛꢞ ꢙꢘ ꢄꢡꢨ ꢜꢞ ꢍꢗꢞ ꢝꢚ ꢠꢛ ꢡꢗꢝ ꢞ
ꢞ ꢝ ꢜ ꢗꢥ ꢜ ꢚꢥ ꢩ ꢜ ꢚꢚ ꢜ ꢗ ꢝꢪꢦ ꢔꢚ ꢙ ꢥꢠꢟ ꢝꢖꢙꢗ ꢢꢚ ꢙꢟ ꢡꢞ ꢞꢖ ꢗꢫ ꢥꢙꢡ ꢞ ꢗꢙꢝ ꢗꢡ ꢟꢡ ꢞꢞ ꢜꢚ ꢖꢤ ꢪ ꢖꢗꢟ ꢤꢠꢥ ꢡ
ꢝ ꢡ ꢞ ꢝꢖ ꢗꢫ ꢙꢘ ꢜ ꢤꢤ ꢢꢜ ꢚ ꢜ ꢛ ꢡ ꢝ ꢡ ꢚ ꢞ ꢦ
Copyright 1996, Texas Instruments Incorporated
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀꢁ ꢂꢃ ꢄ ꢅꢅꢅ ꢆꢇ
ꢊ
ꢈ
ꢉ
ꢂ
ꢊ
ꢋ
ꢌ
ꢍ
ꢎ
ꢏ
ꢄꢐ
ꢁ
ꢌ
ꢊ
ꢍ
ꢎ
ꢏ
ꢈ
ꢏ
ꢃ
ꢐ
ꢈ
ꢏ
ꢑ
ꢒ
ꢈ
ꢏ
ꢓ
ꢉ
ꢊꢄ
ꢍ
ꢔ
ꢊ
ꢏ
ꢕ
ꢏ
ꢑ
SCAS175A − SEPTEMBER 1991 − REVISED APRIL 1996
†
logic symbol
16
1
DMUX
0
0
1Y0
1Y1
1Y2
1Y3
15
1A
1
2
1
2
3
G
14
3
1B
2
13
3
1G
5
6
7
8
2Y0
2Y1
2Y2
2Y3
10
2A
9
2B
11
2G
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
logic diagram (positive logic)
16
1
1Y0
13
1G
1Y1
2
1Y2
1Y3
15
14
1A
1B
3
5
6
2Y0
2Y1
11
2G
7
8
2Y2
2Y3
10
9
2A
2B
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂꢃ ꢄꢅꢅꢅꢆ ꢇ
ꢈꢉꢂ ꢊ ꢋ ꢌꢊ ꢍꢎꢏ ꢄ ꢐ ꢁ ꢌꢊ ꢍꢎꢏ ꢈꢏꢃ ꢐꢈ ꢏꢑꢒ ꢈꢏꢓ ꢉꢊꢄꢍ ꢔ ꢊꢏ ꢕꢏ ꢑ
SCAS175A − SEPTEMBER 1991 − REVISED APRIL 1996
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
CC
Input voltage range, V (see Note 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to V
+ 0.5 V
+ 0.5 V
I
CC
CC
Output voltage range, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to V
O
Input clamp current, I (V < 0 or V > V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA
IK
I
I
CC
O
Output clamp current, I
(V < 0 or V > V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
OK
O
CC
Continuous output current, I (V = 0 to V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA
Continuous current through V
O
O
CC
CC
or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA
Maximum power dissipation at T = 55°C (in still air) (see Note 2): D package . . . . . . . . . . . . . . . . . . . . 1.3 W
A
N package . . . . . . . . . . . . . . . . . . . . 1.1 W
PW package . . . . . . . . . . . . . . . . . . . 0.5 W
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
stg
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The maximum package power dissipation is calculated using a junction temperature of 150_C and a board trace length of 750 mils,
except for the N package, which has a trace length of zero.
recommended operating conditions (see Note 3)
MIN NOM
MAX
UNIT
V
V
V
V
V
V
Supply voltage
4.5
2
5
5.5
CC
IH
IL
High-level input voltage
Low-level input voltage
Input voltage
V
0.8
V
0
0
V
V
V
I
CC
Output voltage
V
O
CC
I
I
High-level output current
Low-level output current
Input transition rise or fall rate
Operating free-air temperature
−24
24
mA
mA
ns/V
°C
OH
OL
∆t/∆v
0
10
T
−40
85
A
NOTE 3: Unused or floating inputs must be held high or low.
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀꢁ ꢂꢃ ꢄ ꢅꢅꢅ ꢆꢇ
ꢈ ꢉꢂꢊ ꢋ ꢌꢊ ꢍ ꢎꢏ ꢄꢐ ꢁ ꢌꢊꢍ ꢎ ꢏ ꢈꢏ ꢃꢐ ꢈꢏ ꢑꢒ ꢈ ꢏꢓꢉ ꢊꢄ ꢍꢔ ꢊꢏ ꢕꢏꢑ
SCAS175A − SEPTEMBER 1991 − REVISED APRIL 1996
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
T
A
= 25°C
PARAMETER
TEST CONDITIONS
V
MIN
MAX
UNIT
CC
MIN
4.4
TYP
MAX
4.5 V
5.5 V
4.5 V
5.5 V
5.5 V
4.5 V
5.5 V
4.5 V
5.5 V
5.5 V
5.5 V
5.5 V
5.5 V
5 V
4.4
5.4
I
= −50 mA
OH
5.4
3.94
4.94
3.8
V
V
V
OH
OL
I
I
= −24 mA
= −75 mA
OH
4.8
†
3.85
OH
0.1
0.1
0.1
0.1
0.44
0.44
1.65
1
I
= 50 mA
OL
0.36
0.36
V
I
I
= 24 mA
OL
†
= 75 mA
OL
I
I
V = V
or GND
or GND,
0.1
8
mA
mA
mA
pF
I
I
CC
V = V
I = 0
O
80
CC
I
CC
‡
∆I
CC
One input at 3.4 V,
V = V or GND
Other inputs at V
CC
or GND
0.9
1
C
3.5
i
I
CC
†
‡
Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms.
This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or V
.
CC
switching characteristics over recommended operating free-air temperature range,
= 5 V 0.5 V (unless otherwise noted) (see Figure 1)
V
CC
T
A
= 25°C
TYP
5.7
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
MIN
MAX
UNIT
ns
MIN
1.7
2.1
2.7
1.8
MAX
7.8
t
t
t
t
1.7
2.1
2.7
1.8
8.5
8.5
7.9
7.5
PLH
PHL
PLH
PHL
A or B
G
Y
Y
5.5
7.4
5.3
7.2
ns
4.3
6.7
operating characteristics, V
= 5 V, T = 25°C
A
CC
PARAMETER
Power dissipation capacitance
TEST CONDITIONS
= 50 pF, f = 1 MHz
L
TYP
UNIT
C
C
47
pF
pd
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
ꢀ ꢁ ꢂꢃ ꢄꢅꢅꢅꢆ ꢇ
ꢈꢉꢂ ꢊ ꢋ ꢌꢊ ꢍꢎꢏ ꢄ ꢐ ꢁ ꢌꢊ ꢍꢎꢏ ꢈꢏꢃ ꢐꢈ ꢏꢑꢒ ꢈꢏꢓ ꢉꢊꢄꢍ ꢔ ꢊꢏ ꢕꢏ ꢑ
SCAS175A − SEPTEMBER 1991 − REVISED APRIL 1996
PARAMETER MEASUREMENT INFORMATION
3 V
0 V
Input
1.5 V
1.5 V
From Output
Under Test
(see Note B)
t
t
PHL
PLH
C
= 50 pF
L
500 Ω
(see Note A)
V
OH
CC
50% V
CC
50% V
Output
V
OL
VOLTAGE WAVEFORMS
LOAD CIRCUIT
C includes probe and jig capacitance.
L
NOTES: A.
B. Input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, Z = 50 Ω, t = 3 ns, t = 3 ns.
O
r
f
C. The outputs are measured one at a time with one input transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
74ACT11139D
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
SOIC
SOIC
SOIC
D
16
16
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
ACT11139
74ACT11139DE4
74ACT11139DG4
ACTIVE
ACTIVE
D
D
40
40
Green (RoHS
& no Sb/Br)
-40 to 85
ACT11139
ACT11139
ACT11139
Green (RoHS
& no Sb/Br)
-40 to 85
74ACT11139DR
74ACT11139DRE4
74ACT11139DRG4
74ACT11139N
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
ACTIVE
SOIC
SOIC
D
D
16
16
16
16
16
16
TBD
TBD
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
SOIC
D
Call TI
Call TI
PDIP
N
Call TI
Call TI
74ACT11139PWLE
74ACT11139PWR
TSSOP
TSSOP
PW
PW
Call TI
Call TI
2000
2000
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
AT139
AT139
AT139
74ACT11139PWRE4
74ACT11139PWRG4
ACTIVE
ACTIVE
TSSOP
TSSOP
PW
PW
16
16
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
74ACT11139PWR
TSSOP
PW
16
2000
330.0
12.4
6.9
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
TSSOP PW 16
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 35.0
74ACT11139PWR
2000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明