ADC14L040CIVY/NOPB [TI]
14 位、40MSPS 模数转换器 (ADC) | NEY | 32 | -40 to 85;型号: | ADC14L040CIVY/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 14 位、40MSPS 模数转换器 (ADC) | NEY | 32 | -40 to 85 转换器 模数转换器 |
文件: | 总32页 (文件大小:998K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
ADC14L040 14-Bit, 40 MSPS, 235 mW A/D Converter
Check for Samples: ADC14L040
1
FEATURES
DESCRIPTION
The ADC14L040 is a low power monolithic CMOS
analog-to-digital converter capable of converting
analog input signals into 14-bit digital words at 40
Megasamples per second (MSPS). This converter
uses a differential, pipeline architecture with digital
error correction and an on-chip sample-and-hold
circuit to minimize power consumption while providing
excellent dynamic performance and a 150 MHz Full
Power Bandwidth. Operating on a single +3.3V power
supply, the ADC14L040 achieves 11.9 effective bits
at nyquist and consumes just 235 mW at 40 MSPS .
The Power Down feature reduces power consumption
to 15 mW.
2
•
•
•
•
•
•
Single +3.3V Supply Operation
Internal Sample-and-Hold
Internal Reference
Outputs 2.4V to 3.6V Compatible
Duty Cycle Stabilizer
Power Down Mode
APPLICATIONS
•
•
•
•
Medical Imaging
Instrumentation
Communications
Digital Video
The differential inputs provide a full scale differential
input swing equal to 2 times VREF with the possibility
of a single-ended input. Full use of the differential
input is recommended for optimum performance.
Duty cycle stabilization and output data format are
selectable using a quad state function pin. The output
data can be set for offset binary or two's complement.
KEY SPECIFICATIONS
•
•
•
•
•
•
Resolution 14 Bits
DNL ±0.5 LSB (typ)
SNR (fIN = 10 MHz) 74 dB (typ)
SFDR (fIN = 10 MHz) 90 dB (typ)
Data Latency 7 Clock Cycles
Power Consumption
To ease interfacing to lower voltage systems, the
digital output driver power pins of the ADC14L040
can be connected to a separate supply voltage in the
range of 2.4V to the analog supply voltage.
This device is available in the 32-lead LQFP package
and will operate over the industrial temperature range
of −40°C to +85°C. An evaluation board is available
to ease the evaluation process.
–
–
Operating 235 mW (typ)
Power Down Mode 15 mW (typ)
Connection Diagram
1
2
3
4
5
6
7
8
24
V
D10
REF
23
V
+
-
D9
IN
22
V
D8
IN
21
V
AGND
ADC14L040
(Top View)
DR
20
19
18
17
V
A
DRGND
V
D
D7
D6
D5
AGND
PD
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2013, Texas Instruments Incorporated
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
Block Diagram
VIN+
S/H
Stage 1
Stage 2
Stage 3
Stage 9
Stage 10
Stage 11
VIN
-
2
2
3
3
2
2
3
3
3
3
3
3
Timing
Control
11-Stage Pipeline Converter
24
14
14
Digital
Correction
Output
Buffers
D0-D13
3
Duty Cycle
Stabilizer
CLK
VRP
VRM
VRN
Reference
Select
Internal
Reference
VREF
2
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
PIN DESCRIPTIONS and EQUIVALENT CIRCUITS
Pin No.
ANALOG I/O
2
Symbol
Equivalent Circuit
Description
V
A
VIN+
Differential analog input pins. With a 1.0V reference voltage the
differential full-scale input signal level is 2.0 VP-P with each input pin
voltage centered on a common mode voltage, VCM. The negative
input pins may be connected to VCM for single-ended operation, but
a differential input signal is required for best performance.
3
VIN−
AGND
V
A
This pin is the reference select pin and the external reference input.
If (VA - 0.3V) < VREF < VA, the internal 1.0V reference is selected.
If AGND < VREF < (AGND + 0.3V), the internal 0.5V reference is
selected.
1
VREF
If a voltage in the range of 0.4V to (VA - 0.4V) is applied to this pin,
that voltage is used as the reference.
The full scale differential voltage range is 2 * VREF. VREF should be
bypassed to AGND with a 0.1 µF capacitor when an external
reference is used.
AGND
V
A
31
32
VRP
VRM
V
A
These pins should each be bypassed to AGND with a low ESL
(equivalent series inductance) 0.1 µF capacitor. A 10 µF capacitor
V
A
should be placed between the VRP and VRN
.
VRM may be loaded to 1mA for use as a temperature stable 1.5V
reference. The remaining pins should not be loaded.
VRM may be used to provide the common mode voltage, VCM, for the
differential inputs.
30
VRN
V
A
AGND
AGND
V
A
V
Float
This is a four-state pin.
DF/DCS = VA, output data format is offset binary with duty cycle
stabilization applied to the input clock
DF/DCS = AGND, output data format is 2's complement, with duty
cycle stabilization applied to the input clock.
11
DF/DCS
DF/DCS = VRM , output data is 2's complement without duty cycle
stabilization applied to the input clock
DF/DCS = "float", output data is offset binary without duty cycle
stabilization applied to the input clock.
AGND
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
PIN DESCRIPTIONS and EQUIVALENT CIRCUITS (continued)
Pin No.
Symbol
Equivalent Circuit
Description
DIGITAL I/O
V
D
Digital clock input. The range of frequencies for this input is as
specified in the electrical tables with specified performance at 40
MHz. The input is sampled on the rising edge.
V
A
10
CLK
PD is the Power Down input pin. When high, this input puts the
converter into the power down mode. When this pin is low, the
converter is in the active mode.
8
PD
AGND
DGND
V
V
DR
A
Digital data output pins that make up the 14-bit conversion result. D0
(pin 12) is the LSB, while D13 (pin 27) is the MSB of the output
word. Output levels are TTL/CMOS compatible. Optimum loading is
< 10pF.
12-19
22-27
D0–D13
AGND
DR GND
ANALOG POWER
Positive analog supply pins. These pins should be connected to a
quiet +3.3V source and bypassed to AGND with 0.1 µF capacitors
located close to these power pins, and with a 10 µF capacitor.
5, 29
VA
4, 7, 28
AGND
The ground return for the analog supply.
DIGITAL POWER
Positive digital supply pin. This pin should be connected to the same
quiet +3.3V source as is VA and be bypassed to DGND with a 0.1 µF
capacitor located close to the power pin and with a 10 µF capacitor.
6
9
VD
DGND
The ground return for the digital supply.
Positive driver supply pin for the ADC14L040's output drivers. This
pin should be connected to a voltage source of +2.4V to VD and be
bypassed to DR GND with a 0.1 µF capacitor. If the supply for this
pin is different from the supply used for VA and VD, it should also be
bypassed with a 10 µF capacitor. VDR should never exceed the
voltage on VD. All 0.1 µF bypass capacitors should be located close
to the supply pin.
21
20
VDR
The ground return for the digital supply for the ADC's output drivers.
These pins should be connected to the system digital ground, but
not be connected in close proximity to the ADC's DGND or AGND
pins. See LAYOUT AND GROUNDING for more details.
DR GND
4
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)(3)
VA, VD, VDR
4.2V
≤ 100 mV
|VA–VD|
Voltage on Any Input or Output Pin
Input Current at Any Pin(4)
Package Input Current(4)
Package Dissipation at TA = 25°C
ESD Susceptibility
−0.3V to (VA or VD +0.3V)
±25 mA
±50 mA
(5)
See
Human Body Model(6)
Machine Model(6)
2500V
250V
Storage Temperature
−65°C to +150°C
Soldering process must comply with TI's Reflow Temperature Profile specifications. Refer to www.ti.com/packaging(7)
(1) All voltages are measured with respect to GND = AGND = DGND = 0V, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
(4) When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA), the current at that pin should be
limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies
with an input current of 25 mA to two.
(5) The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by
TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature, (TA), and can be calculated using the formula
PDMAX = (TJmax - TA )/θJA. The values for maximum power dissipation listed above will be reached only when the device is operated in
a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is
reversed). Obviously, such conditions should always be avoided.
(6) Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through 0Ω.
(7) Reflow temperature profiles are different for lead-free and non-lead-free packages.
Operating Ratings(1)(2)
Operating Temperature
Supply Voltage (VA, VD)
Output Driver Supply (VDR
CLK, PD
−40°C ≤ TA ≤ +85°C
+3.0V to +3.6V
+2.4V to VD
)
−0.05V to (VD + 0.05V)
20% to 80%
Clock Duty Cycle (DCS On)
Clock Duty Cycle (DCS Off)
Analog Input Pins
VCM
40% to 60%
0V to 2.6V
0.5V to 2.0V
|AGND–DGND|
≤100mV
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
(2) All voltages are measured with respect to GND = AGND = DGND = 0V, unless otherwise specified.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
Converter Electrical Characteristics(1)(2)(3)
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 20 MHz at -0.5dBFS, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle
Stabilizer On. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
Typical
Limits
Units
(Limits)
Symbol
Parameter
Conditions
(4)
(4)
STATIC CONVERTER CHARACTERISTICS
Resolution with No Missing Codes
14
Bits (min)
LSB (max)
LSB (max)
%FS (max)
%FS (max)
ppm/°C
INL
Integral Non Linearity(5)
Differential Non Linearity
Positive Gain Error
±1.5
±0.5
0.3
±3.8
±1.0
±3.3
±3.3
DNL
PGE
NGE
TC GE
VOFF
Negative Gain Error
0.4
Gain Error Tempco
−40°C ≤ TA ≤ +85°C
2.5
Offset Error (VIN+ = VIN−)
-0.06
1.5
±1.0
%FS (max)
ppm/°C
TC VOFF Offset Error Tempco
Under Range Output Code
Over Range Output Code
−40°C ≤ TA ≤ +85°C
0
16383
REFERENCE AND ANALOG INPUT CHARACTERISTICS
0.5
2.0
V (min)
V (max)
V
VCM
VRM
CIN
Common Mode Input Voltage
Reference Output Voltage
1.5
Output load = 1 mA
1.5
11
(CLK LOW)
(CLK HIGH)
pF
VIN = 1.5 Vdc ± 0.5
V
VIN Input Capacitance (each pin to GND)
4.5
pF
0.8
1.2
V (min)
V (max)
MΩ (min)
VREF
External Reference Voltage(6)
Reference Input Resistance
1.00
1
DYNAMIC CONVERTER CHARACTERISTICS
FPBW
Full Power Bandwidth
0 dBFS Input, Output at −3 dB
fIN = 10 MHz
150
74
MHz
dBc
dBc
dBc
dBc
Bits
Bits
SNR
Signal-to-Noise Ratio
fIN = 20 MHz
73.3
73.5
73
71.7
71.5
11.6
fIN = 10 MHz
SINAD
ENOB
Signal-to-Noise Ratio and Distortion
Effective Number of Bits
fIN = 20 MHz
fIN = 10 MHz
12
fIN = 20 MHz
11.9
(1) The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided
current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above
VA or below GND by more than 100 mV. As an example, if VA is +3.3V, the full-scale input voltage must be ≤+3.4V to ensure accurate
conversions.
V
A
I/O
To Internal Circuitry
AGND
(2) To ensure accuracy, it is required that |VA–VD| ≤ 100 mV and separate bypass capacitors are used at each power supply pin.
(3) With the test condition for VREF = +1.0V (2VP-P differential input), the 14-bit LSB is 122.1 µV.
(4) Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are specified to TI's AOQL (Average Outgoing
Quality Level).
(5) Integral Non Linearity is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through
positive and negative full-scale.
(6) Optimum performance will be obtained by keeping the reference input in the 0.8V to 1.2V range. The LM4051CIM3-ADJ (SOT-23
package) is recommended for external reference applications.
6
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
Converter Electrical Characteristics(1)(2)(3) (continued)
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 20 MHz at -0.5dBFS, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle
Stabilizer On. Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
Typical
Limits
Units
(Limits)
Symbol
Parameter
Conditions
(4)
(4)
fIN = 10 MHz
fIN = 20 MHz
fIN = 10 MHz
fIN = 20 MHz
fIN = 10 MHz
fIN = 20 MHz
fIN = 10 MHz
fIN = 20 MHz
-86
-86
-93
-91
-90
-94
90
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
THD
Total Harmonic Disortion
-77
-80
-80
80
H2
H3
Second Harmonic Distortion
Third Harmonic Distortion
SFDR
IMD
Spurious Free Dynamic Range
Intermodulation Distortion
90
fIN = 9.6 MHz and 10.2 MHz, each = −6.5
−79
dBFS
dBFS
DC and Logic Electrical Characteristics(1)(2)(3)
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 20 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
Units
(Limits)
(4)
(4)
Symbol
Parameter
Conditions
Typical
Limits
CLK, PD DIGITAL INPUT CHARACTERISTICS
VIN(1)
VIN(0)
IIN(1)
IIN(0)
CIN
Logical “1” Input Voltage
Logical “0” Input Voltage
Logical “1” Input Current
Logical “0” Input Current
Digital Input Capacitance
VD = 3.6V
VD = 3.0V
VIN = 3.3V
VIN = 0V
2.0
1.0
V (min)
V (max)
µA
10
−10
5
µA
pF
D0–D13 DIGITAL OUTPUT CHARACTERISTICS
VDR = 2.5V
VDR = 3V
2.3
2.7
0.4
V (min)
V (min)
V (max)
mA
VOUT(1)
Logical “1” Output Voltage
IOUT = −0.5 mA
VOUT(0)
+ISC
Logical “0” Output Voltage
IOUT = 1.6 mA, VDR = 3V
VOUT = 0V
Output Short Circuit Source Current
Output Short Circuit Sink Current
Digital Output Capacitance
−10
10
5
−ISC
VOUT = VDR
mA
COUT
pF
POWER SUPPLY CHARACTERISTICS
PD Pin = DGND, VREF = VA
PD Pin = VD
63
4.5
86
mA (max)
mA
IA Analog Supply Current
(1) The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided
current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above
VA or below GND by more than 100 mV. As an example, if VA is +3.3V, the full-scale input voltage must be ≤+3.4V to ensure accurate
conversions.
V
A
I/O
To Internal Circuitry
AGND
(2) To ensure accuracy, it is required that |VA–VD| ≤ 100 mV and separate bypass capacitors are used at each power supply pin.
(3) With the test condition for VREF = +1.0V (2VP-P differential input), the 14-bit LSB is 122.1 µV.
(4) Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are specified to TI's AOQL (Average Outgoing
Quality Level).
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
DC and Logic Electrical Characteristics(1)(2)(3) (continued)
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 20 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
Units
(Limits)
(4)
(4)
Symbol
ID
IDR
Parameter
Digital Supply Current
Conditions
Typical
Limits
12
PD Pin = DGND
8
0
mA (max)
mA
PD Pin = VD , fCLK = 0
(5)
(6)
PD Pin = DGND, CL = 5 pF
PD Pin = VD, fCLK = 0
4
0
mA
mA
Digital Output Supply Current
Total Power Consumption
PD Pin = DGND, CL = 5 pF
PD Pin = VD, clock on
235
15
323
mW (max)
mW
Power Down Power Consumption
Rejection of Full-Scale Error with
VA =3.0V vs. 3.6V
PSRR Power Supply Rejection Ratio
72
dB
(5) IDR is the current consumed by the switching of the output drivers and is primarily determined by load capacitance on the output pins,
the supply voltage, VDR, and the rate at which the outputs are switching (which is signal dependent). IDR=VDR(C0 x f0 + C1 x f1 +....C11
f11) where VDR is the output driver power supply voltage, Cn is total capacitance on the output pin, and fn is the average frequency at
which that pin is toggling.
x
(6) Excludes IDR. See Note 5.
AC Electrical Characteristics
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 10 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
(1)(2)(3)(4)
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
Units
Symbol
Parameter
Conditions
Typical(5) Limits(5)
(Limits)
MHz (min)
MHz
1
fCLK
Maximum Clock Frequency
Minimum Clock Frequency
Clock High Time
40
2
fCLK
5
tCH
Duty Cycle Stabilizer On
12.5
12.5
12.5
12.5
5
5
ns (min)
ns (min)
ns (min)
ns (min)
tCL
Clock Low Time
Duty Cycle Stabilizer On
Duty Cycle Stabilizer Off
Duty Cycle Stabilizer Off
tCH
Clock High Time
10
10
7
tCL
Clock Low Time
tCONV
Conversion Latency
Clock Cycles
Data Output Delay after Rising Clock
Edge
tOD
6
9.6
ns (max)
tAD
tAJ
Aperture Delay
Aperture Jitter
2
ns
0.7
ps rms
0.1 µF on pins 30, 31, 32; 10 µF between
pins 30, 31
tPD
Power Down Mode Exit Cycle
280
µs
(1) The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided
current is limited per Note 4 under Absolute Maximum Ratings. However, errors in the A/D conversion can occur if the input goes above
VA or below GND by more than 100 mV. As an example, if VA is +3.3V, the full-scale input voltage must be ≤+3.4V to ensure accurate
conversions.
V
A
I/O
To Internal Circuitry
AGND
(2) To ensure accuracy, it is required that |VA–VD| ≤ 100 mV and separate bypass capacitors are used at each power supply pin.
(3) With the test condition for VREF = +1.0V (2VP-P differential input), the 14-bit LSB is 122.1 µV.
(4) Timing specifications are tested at TTL logic levels, VIL = 0.4V for a falling edge and VIH = 2.4V for a rising edge.
(5) Typical figures are at TJ = 25°C, and represent most likely parametric norms. Test limits are specified to TI's AOQL (Average Outgoing
Quality Level).
8
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
SPECIFICATION DEFINITIONS
APERTURE DELAY is the time after the rising edge of the clock to when the input signal is acquired or held for
conversion.
APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample.
Aperture jitter manifests itself as noise in the output.
CLOCK DUTY CYCLE is the ratio of the time during one cycle that a repetitive digital waveform is high to the
total time of one period. The specification here refers to the ADC clock input signal.
COMMON MODE VOLTAGE (VCM) is the common d.c. voltage applied to both input terminals of the ADC.
CONVERSION LATENCY is the number of clock cycles between initiation of conversion and when that data is
presented to the output driver stage. Data for any given sample is available at the output pins the Pipeline Delay
plus the Output Delay after the sample is taken. New data is available at every clock cycle, but the data lags the
conversion by the pipeline delay.
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1
LSB.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise
and Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a
perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental
drops 3 dB below its low frequency value for a full scale input.
GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated as:
Gain Error = Positive Full Scale Error − Negative Full Scale Error
(1)
(2)
It can also be expressed as Positive Gain Error and Negative Gain Error, which are calculated as:
PGE = Positive Full Scale Error - Offset Error NGE = Offset Error - Negative Full Scale Error
INTEGRAL NON LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from
negative full scale (½ LSB below the first code transition) through positive full scale (½ LSB above the last code
transition). The deviation of any given code from this straight line is measured from the center of that code value.
INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two
sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in
the intermodulation products to the total power in the original frequencies. IMD is usually expressed in dBFS.
LSB (LEAST SIGNIFICANT BIT) is the bit that has the smallest value or weight of all bits. This value is VFS/2n,
where “VFS” is the full scale input voltage and “n” is the ADC resolution in bits.
MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC14L040 is ensured
not to have any missing codes.
MSB (MOST SIGNIFICANT BIT) is the bit that has the largest value or weight. Its value is one half of full scale.
NEGATIVE FULL SCALE ERROR is the difference between the actual first code transition and its ideal value of
½ LSB above negative full scale.
OFFSET ERROR is the difference between the two input voltages [(VIN+) – (VIN-)] required to cause a transition
from code 8191 to 8192.
OUTPUT DELAY is the time delay after the rising edge of the clock before the data update is presented at the
output pins.
PIPELINE DELAY (LATENCY) See CONVERSION LATENCY.
POSITIVE FULL SCALE ERROR is the difference between the actual last code transition and its ideal value of
1½ LSB below positive full scale.
POWER SUPPLY REJECTION RATIO (PSRR) is a measure of how well the ADC rejects a change in the power
supply voltage. PSRR is the ratio of the change in Full-Scale Error that results from a change in the d.c. power
supply voltage, expressed in dB.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms
value of the sum of all other spectral components below one-half the sampling frequency, not including
harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the
input signal to the rms value of all of the other spectral components below half the clock frequency, including
harmonics but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the rms values of the
input signal and the peak spurious signal, where a spurious signal is any signal present in the output spectrum
that is not present at the input.
TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB, of the rms total of the first nine harmonic
levels at the output to the level of the fundamental at the output. THD is calculated as
(3)
where f1 is the RMS power of the fundamental (output) frequency and f2 through f10 are the RMS power of the
first 9 harmonic frequencies in the output spectrum.
SECOND HARMONIC DISTORTION (2ND HARM) is the difference expressed in dB, between the RMS power in
the input frequency at the output and the power in its 2nd harmonic level at the output.
THIRD HARMONIC DISTORTION (3RD HARM) is the difference, expressed in dB, between the RMS power in
the input frequency at the output and the power in its 3rd harmonic level at the output.
Timing Diagram
Sample N + 8
Sample N + 7
Sample N + 6
Sample N
Sample N + 9
Sample N + 10
V
IN
t
AD
1
f
CLK
Clock N
Clock N + 7
90%
10%
90%
10%
CLK
t
t
CL
CH
t
f
t
r
t
OD
D0 - D13
Data N + 1 Data N + 2
Data N - 1
Data N
Latency
Figure 1. Output Timing
10
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
Transfer Characteristic
Figure 2. Transfer Characteristic
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS, DNL, INL
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 0 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
DNL
INL
Figure 3.
Figure 4.
DNL vs. fCLK
INL vs. fCLK
Figure 5.
Figure 6.
DNL vs. Clock Duty Cycle
INL vs. Clock Duty Cycle
Figure 7.
Figure 8.
12
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
TYPICAL PERFORMANCE CHARACTERISTICS, DNL, INL (continued)
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 0 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
DNL vs. Temperature
INL vs. Temperature
Figure 9.
Figure 10.
DNL vs. VDR, VA = VD = 3.6V
INL vs. VDR, VA = VD = 3.6V
Figure 11.
Figure 12.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 20 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
SNR,SINAD,SFDR vs. VA
Distortion vs. VA
Figure 13.
Figure 14.
SNR,SINAD,SFDR vs. VDR, VA = VD = 3.6V
Distortion vs. VDR, VA = VD = 3.6V
Figure 15.
Figure 16.
SNR,SINAD,SFDR vs. VCM
Distortion vs. VCM
Figure 17.
Figure 18.
14
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 20 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
SNR,SINAD,SFDR vs. fCLK
Distortion vs. fCLK
Figure 19.
Figure 20.
SNR,SINAD,SFDR vs. Clock Duty Cycle
Distortion vs. Clock Duty Cycle
Figure 21.
Figure 22.
SNR,SINAD,SFDR vs. VREF
Distortion vs. VREF
Figure 23.
Figure 24.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 20 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
SNR,SINAD,SFDR vs. fIN
Distortion vs. fIN
Figure 25.
Figure 26.
SNR,SINAD,SFDR vs. Temperature
Distortion vs. Temperature
Figure 27.
Figure 28.
tOD vs. VDR, VA = VD = 3.6V
Spectral Response @ 4.4 MHz Input
Figure 29.
Figure 30.
16
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +3.3V, VDR
=
+2.5V, PD = 0V, External VREF = +1.0V, fCLK = 40 MHz, fIN = 20 MHz, tr = tf = 2 ns, CL = 15 pF/pin, Duty Cycle Stabilizer On.
Boldface limits apply for TJ = TMIN to TMAX: all other limits TJ = 25°C
Spectral Response @ 10 MHz Input
Spectral Response @ 20 MHz Input
Figure 31.
Figure 32.
Intermodulation Distortion, fIN1= 9.6 MHz, fIN2 = 10.2 MHz
Figure 33.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
FUNCTIONAL DESCRIPTION
Operating on a single +3.3V supply, the ADC14L040 uses a pipeline architecture and has error correction
circuitry to help ensure maximum performance. The differential analog input signal is digitized to 14 bits. The
user has the choice of using an internal 1.0 Volt or 0.5 Volt stable reference, or using an external reference. Any
external reference is buffered on-chip to ease the task of driving that pin.
The output word rate is the same as the clock frequency. For the ADC14L040 the clock frequency can be
between 5 MSPS and 40 MSPS (typical) with fully specified performance at 40 MSPS. The analog input is
acquired at the rising edge of the clock and the digital data for a given sample is delayed by the pipeline for 7
clock cycles. Duty cycle stabilization and output data format are selectable using the quad state function DF/DCS
pin. The output data can be set for offset binary or two's complement.
A logic high on the power down (PD) pin reduces the converter power consumption to 15 mW.
Applications Information
OPERATING CONDITIONS
We recommend that the following conditions be observed for operation of the ADC14L040:
3.0V ≤ VA ≤ 3.6V
VD = VA
2.4V ≤ VDR ≤ VA
5 MHz ≤ fCLK ≤ 40 MHz
0.8V ≤ VREF ≤ 1.2V (for an external reference)
0.5V ≤ VCM ≤ 2.0V
Analog Inputs
There is one reference input pin, VREF, which is used to select an internal reference, or to supply an external
reference. The ADC14L040 has one analog signal input pairs, VIN + and VIN - . This pair of pins forms a
differential input pair.
Reference Pins
The ADC14L040 is designed to operate with an internal 1.0V or 0.5V reference, or an external 1.0V reference,
but performs well with external reference voltages in the range of 0.8V to 1.2V. Lower reference voltages will
decrease the signal-to-noise ratio (SNR) of the ADC14L040. Increasing the reference voltage (and the input
signal swing) beyond 1.2V may degrade THD for a full-scale input, especially at higher input frequencies.
It is important that all grounds associated with the reference voltage and the analog input signal make connection
to the ground plane at a single, quiet point to minimize the effects of noise currents in the ground path.
The Reference Bypass Pins (VRP, VRM, and VRN) are made available for bypass purposes. All these pins should
each be bypassed to ground with a 0.1 µF capacitor. A 10 µF capacitor should be placed between the VRP and
VRN pins, as shown in Figure 36. This configuration is necessary to avoid reference oscillation, which could result
in reduced SFDR and/or SNR. VRM may be loaded to 1mA for use as a temperature stable 1.5V reference. The
remaining pins should not be loaded.
Smaller capacitor values than those specified will allow faster recovery from the power down mode, but may
result in degraded noise performance. Loading any of these pins other than VRM may result in performance
degradation.
The nominal voltages for the reference bypass pins are as follows:
VRM = 1.5 V
VRP = VRM + VREF / 2
VRN = VRM − VREF / 2
18
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
User choice of an on-chip or external reference voltage is provided. The internal 1.0 Volt reference is in use
when the the VREF pin is connected to VA. When the VREF pin is connected to AGND, the internal 0.5 Volt
reference is in use. If a voltage in the range of 0.8V to 1.2V is applied to the VREF pin, that is used for the voltage
reference. When an external reference is used, the VREF pin should be bypassed to ground with a 0.1 µF
capacitor close to the reference input pin. There is no need to bypass the VREF pin when the internal reference is
used.
Signal Inputs
The signal inputs are VIN + and VIN− . The input signal, VIN, is defined as
VIN = (VIN+) – (VIN−)
(4)
Figure 34 shows the expected input signal range. Note that the common mode input voltage, VCM, should be in
the range of 0.5V to 2.0V.
The peaks of the individual input signals should each never exceed 2.6V.
The ADC14L040 performs best with a differential input signal with each input centered around a common mode
voltage, VCM. The peak-to-peak voltage swing at each analog input pin should not exceed the value of the
reference voltage or the output data will be clipped.
The two input signals should be exactly 180° out of phase from each other and of the same amplitude. For single
frequency inputs, angular errors result in a reduction of the effective full scale input. For complex waveforms,
however, angular errors will result in distortion.
Figure 34. Expected Input Signal Range
For single frequency sine waves the full scale error in LSB can be described as approximately
EFS = 16384 ( 1 - sin (90° + dev))
(5)
Where dev is the angular difference in degrees between the two signals having a 180° relative phase relationship
to each other (see Figure 35). Drive the analog inputs with a source impedance less than 100Ω.
Figure 35. Angular Errors Between the Two Input Signals Will Reduce the Output Level or Cause
Distortion
For differential operation, each analog input pin of the differential pair should have a peak-to-peak voltage equal
to the reference voltage, VREF, be 180 degrees out of phase with each other and be centered around VCM
.
Single-Ended Operation
Performance with a differential input signal is better than with a single-ended signal. For this reason, single-
ended operation is not recommended. However, if single ended-operation is required and the resulting
performance degradation is acceptable, one of the analog inputs should be connected to the d.c. mid point
voltage of the driven input. The peak-to-peak differential input signal at the driven input pin should be twice the
reference voltage to maximize SNR and SINAD performance (Figure 34b). For example, set VREF to 1.0V, bias
VIN− to 1.5V and drive VIN+ with a signal range of 0.5V to 2.5V.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
Because very large input signal swings can degrade distortion performance, better performance with a single-
ended input can be obtained by reducing the reference voltage when maintaining a full-range output. Table 1 and
Table 2 indicate the input to output relationship of the ADC14L040.
Table 1. Input to Output Relationship – Differential Input
+
−
VIN
VIN
Binary Output
2’s Complement Output
10 0000 0000 0000
11 0000 0000 0000
00 0000 0000 0000
01 0000 0000 0000
01 1111 1111 1111
V
CM − VREF/2
CM − VREF/4
VCM
VCM + VREF/2
VCM + VREF/4
VCM
00 0000 0000 0000
01 0000 0000 0000
10 0000 0000 0000
11 0000 0000 0000
11 1111 1111 1111
V
VCM + VREF/4
VCM + VREF/2
V
CM − VREF/4
CM − VREF/2
V
Table 2. Input to Output Relationship – Single-Ended Input
+
−
VIN
VIN
Binary Output
2’s Complement Output
10 0000 0000 0000
11 0000 0000 0000
00 0000 0000 0000
01 0000 0000 0000
01 1111 1111 1111
V
CM − VREF
VCM
VCM
VCM
VCM
VCM
00 0000 0000 0000
01 0000 0000 0000
10 0000 0000 0000
11 0000 0000 0000
11 1111 1111 1111
V
CM − VREF/2
VCM
VCM + VREF/2
VCM + VREF
Driving the Analog Inputs
The VIN+ and the VIN− inputs of the ADC14L040 consist of an analog switch followed by a switched-capacitor
amplifier. The capacitance seen at the analog input pins changes with the clock level, appearing as 11 pF when
the clock is low, and 4.5 pF when the clock is high.
As the internal sampling switch opens and closes, current pulses occur at the analog input pins, resulting in
voltage spikes at the signal input pins. As a driving amplifier attempts to counteract these voltage spikes, a
damped oscillation may appear at the ADC analog input. Do not attempt to filter out these pulses. Rather, use
amplifiers to drive the ADC14L040 input pins that are able to react to these pulses and settle before the switch
opens and another sample is taken. The LMH6702 LMH6628, LMH6622 and the LMH6655 are good amplifiers
for driving the ADC14L040.
To help isolate the pulses at the ADC input from the amplifier output, use RCs at the inputs, as can be seen in
Figure 36 . These components should be placed close to the ADC inputs because the input pins of the ADC is
the most sensitive part of the system and this is the last opportunity to filter that input.
For Nyquist applications the RC pole should be at the ADC sample rate. The ADC input capacitance in the
sample mode should be considered when setting the RC pole. For wideband undersampling applications, the RC
pole should be set at about 1.5 to 2 times the maximum input frequency to maintain a linear delay response.
A single-ended to differential conversion circuit is shown in Figure 37. Table 3 gives resistor values for that circuit
to provide input signals in a range of 1.0V ±0.5V at each of the differential input pins of the ADC14L040.
Table 3. Resistor Values for Circuit of Figure 37
SIGNAL RANGE
0 - 0.25V
R1
open
0Ω
R2
0Ω
R3
R4
R5, R6
1000Ω
499Ω
124Ω
499Ω
100Ω
1500Ω
1500Ω
698Ω
0 - 0.5V
openΩ
698Ω
±0.25V
100Ω
499Ω
Input Common Mode Voltage
The input common mode voltage, VCM, should be in the range of 0.5V to 2.0V and be a value such that the peak
excursions of the analog signal does not go more negative than ground or more positive than 2.6V. See
Reference Pins.
20
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
DIGITAL INPUTS
Digital TTL/CMOS compatible inputs consist of CLK, PD, and DF/DCS.
CLK
The CLK signal controls the timing of the sampling process. Drive the clock input with a stable, low jitter clock
signal in the range indicated in the Electrical Table with rise and fall times of 2 ns or less. The trace carrying the
clock signal should be as short as possible and should not cross any other signal line, analog or digital, not even
at 90°.
The CLK signal also drives an internal state machine. If the CLK is interrupted, or its frequency too low, the
charge on internal capacitors can dissipate to the point where the accuracy of the output data will degrade. This
is what limits the minimum sample rate.
The clock line should be terminated at its source in the characteristic impedance of that line. Take care to
maintain a constant clock line impedance throughout the length of the line. Refer to Application Note AN-905
(SNLA035) for information on setting characteristic impedance.
It is highly desirable that the the source driving the ADC CLK pin only drive that pin. However, if that source is
used to drive other things, each driven pin should be a.c. terminated with a series RC to ground, as shown in
Figure 36, such that the resistor value is equal to the characteristic impedance of the clock line and the capacitor
value is
(6)
where tPD is the signal propagation rate down the clock line, "L" is the line length and ZO is the characteristic
impedance of the clock line. This termination should be as close as possible to the ADC clock pin but beyond it
as seen from the clock source. Typical tPD is about 150 ps/inch (60 ps/cm) on FR-4 board material. The units of
"L" and tPD should be the same (inches or centimeters).
The duty cycle of the clock signal can affect the performance of the A/D Converter. Because achieving a precise
duty cycle is difficult, the ADC14L040 has a Duty Cycle Stabilizer which can be enabled using the DF/DCS pin. It
is designed to maintain performance over a clock duty cycle range of 20% to 80%.
PD
The PD pin, when high, holds the ADC14L040 in a power-down mode to conserve power when the converter is
not being used. The power consumption in this state is 15 mW. The output data pins are undefined and the data
in the pipeline is corrupted while in the power down mode.
The Power Down Mode Exit Cycle time is determined by the value of the components on pins 30, 31 and 32 and
is about 280 µs with the recommended components on the VRP, VRM and VRN reference bypass pins. These
capacitors loose their charge in the Power Down mode and must be recharged by on-chip circuitry before
conversions can be accurate. Smaller capacitor values allow slightly faster recovery from the power down mode,
but can result in a reduction in SNR, SINAD and ENOB performance.
DF/DCS
Duty cycle stabilization and output data format are selectable using this quad state function pin. When enabled,
duty cycle stabilization can compensate for clock inputs with duty cycles ranging from 20% to 80% and generate
a stable internal clock, improving the performance of the part.
With DF/DCS = VA the output data format is offset binary and duty cycle stabilization is applied to the clock. With
DF/DCS = 0 the output data format is 2's complement and duty cycle stabilization is applied to the clock. With
DF/DCS = VRM the output data format is 2's complement and duty cycle stabilization is not used. If DF/DCS is
floating, the output data format is offset binary and duty cycle stabilization is not used. While the sense of this pin
may be changed "on the fly," doing this is not recommended as the output data could be erroneous for a few
clock cycles after this change is made.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
OUTPUTS
The ADC14L040 has 14 TTL/CMOS compatible Data Output pins. Valid data is present at these outputs while
the PD pins is low. Data should be captured with the CLK signal. Depending on the setup and hold time
requirements of the receiving circuit (ASIC), either the rising edge or the falling edge of the CLK signal can be
used to latch the data. Generally, rising-edge capture would maximize setup time with minimal hold time; while
falling-edge-capture would maximize hold time with minimal setup time. However, actual timing for the falling-
edge case depends greatly on the CLK frequency and both cases also depend on the delays inside the ASIC.
Refer to the tOD spec in the AC Electrical Characteristics table.
Be very careful when driving a high capacitance bus. The more capacitance the output drivers must charge for
each conversion, the more instantaneous digital current flows through VDR and DR GND. These large charging
current spikes can cause on-chip ground noise and couple into the analog circuitry, degrading dynamic
performance. Adequate bypassing, limiting output capacitance and careful attention to the ground plane will
reduce this problem. Additionally, bus capacitance beyond the specified 15 pF/pin will cause tOD to increase,
making it difficult to properly latch the ADC output data. The result could be an apparent reduction in dynamic
performance.
To minimize noise due to output switching, minimize the load currents at the digital outputs. This can be done by
connecting buffers (74ACQ541, for example) between the ADC outputs and any other circuitry. Only one driven
input should be connected to each output pin. Additionally, inserting series resistors of about 33Ω at the digital
outputs, close to the ADC pins, will isolate the outputs from trace and other circuit capacitances and limit the
output currents, which could otherwise result in performance degradation. See Figure 36.
+3.3V
1.8 to V Volts
D
CHOKE
2 x 0.1 mF
0.1 mF
+
10 mF
10 mF
0.1 mF
10 mF
1k
1
V
REF
27
26
25
24
23
22
19
18
17
16
15
14
13
12
(MSB) D13
D12
32
31
30
V
V
RM
0.1 mF
D11
330
RP
D10
10 mF
D9
V
RN
0.1 mF
D8
ADC14L040
0.1 mF
D7
D6
D5
Output
Word
74LVTH162374
**
V
IN
33
D4
D3
3
2
3
0.1 mF
V
V
+
-
IN
4
6
1
T1
100 pF
100 pF
0.1 mF
IN
D2
2
1
D1
8
2
2
PD
PD
(LSB) D0
33
DF/DCS
CLK
DF/DCS
T1-6T
CLK
** may be replaced by Ckt in Fig. 5
See
Text
49
49
Clock In
Figure 36. Application Circuit using Transformer Drive Circuit
22
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
2V
R2, 1%
R1, 1%
5k, 1%
+
*
2.4k
to
U2B
+
*
V
+
IN
33
-
U1A
-
5k, 1%
SIGNAL
INPUT
100 pF
R5, 1%
51
5k, 1%
5k, 1%
*
R4, 1%
+
100 pF
R3, 1%
5k, 1%
*
2.4k
to
V
U1B
-
+
-
IN
33
U2A
-
5k, 1%
*
R6, 1%
5k, 1%
The ground
connections
*
Amplifiers:
indicated with an "*" should
be connected to a common
point in the analog ground
plane.
two LMH6622s or
LMH6655s
Figure 37. Differential Drive Circuit of Figure 36
POWER SUPPLY CONSIDERATIONS
The power supply pins should be bypassed with a 10 µF capacitor and with a 0.1 µF ceramic chip capacitor
close to each power pin. Leadless chip capacitors are preferred because they have low series inductance.
As is the case with all high-speed converters, the ADC14L040 is sensitive to power supply noise. Accordingly,
the noise on the analog supply pin should be kept below 100 mVP-P
.
No pin should ever have a voltage on it that is in excess of the supply voltages, not even on a transient basis. Be
especially careful of this during power turn on and turn off.
The VDR pin provides power for the output drivers and may be operated from a supply in the range of 2.4V to VD.
This can simplify interfacing to lower voltage devices and systems. Note, however, that tOD increases with
reduced VDR. DO NOT operate the VDR pin at a voltage higher than VD.
LAYOUT AND GROUNDING
Proper grounding and proper routing of all signals are essential to ensure accurate conversion. Maintaining
separate analog and digital areas of the board, with the ADC14L040 between these areas, is required to achieve
specified performance.
The ground return for the data outputs (DR GND) carries the ground current for the output drivers. The output
current can exhibit high transients that could add noise to the conversion process. To prevent this from
happening, the DR GND pins should NOT be connected to system ground in close proximity to any of the
ADC14L040's other ground pins.
Capacitive coupling between the typically noisy digital circuitry and the sensitive analog circuitry can lead to poor
performance. The solution is to keep the analog circuitry separated from the digital circuitry, and to keep the
clock line as short as possible.
Digital circuits create substantial supply and ground current transients. The logic noise thus generated could
have significant impact upon system noise performance. The best logic family to use in systems with A/D
converters is one which employs non-saturating transistor designs, or has low noise characteristics, such as the
74LS, 74HC(T) and 74AC(T)Q families. The worst noise generators are logic families that draw the largest
supply current transients during clock or signal edges, like the 74F and the 74AC(T) families.
The effects of the noise generated from the ADC output switching can be minimized through the use of 33Ω
resistors in series with each data output line. Locate these resistors as close to the ADC output pins as possible.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
Since digital switching transients are composed largely of high frequency components, total ground plane copper
weight will have little effect upon the logic-generated noise. This is because of the skin effect. Total surface area
is more important than is total ground plane area.
Generally, analog and digital lines should cross each other at 90° to avoid crosstalk. To maximize accuracy in
high speed, high resolution systems, however, avoid crossing analog and digital lines altogether. It is important to
keep clock lines as short as possible and isolated from ALL other lines, including other digital lines. Even the
generally accepted 90° crossing should be avoided with the clock line as even a little coupling can cause
problems at high frequencies. This is because other lines can introduce jitter into the clock line, which can lead to
degradation of SNR. Also, the high speed clock can introduce noise into the analog chain.
Best performance at high frequencies and at high resolution is obtained with a straight signal path. That is, the
signal path through all components should form a straight line wherever possible.
Be especially careful with the layout of inductors. Mutual inductance can change the characteristics of the circuit
in which they are used. Inductors should not be placed side by side, even with just a small part of their bodies
beside each other.
The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input.
Any external component (e.g., a filter capacitor) connected between the converter's input pins and ground or to
the reference input pin and ground should be connected to a very clean point in the ground plane.
All analog circuitry (input amplifiers, filters, reference components, etc.) should be placed in the analog area of
the board. All digital circuitry and I/O lines should be placed in the digital area of the board. The ADC14L040
should be between these two areas. Furthermore, all components in the reference circuitry and the input signal
chain that are connected to ground should be connected together with short traces and enter the ground plane at
a single, quiet point. All ground connections should have a low inductance path to ground.
DYNAMIC PERFORMANCE
To achieve the best dynamic performance, the clock source driving the CLK input must be free of jitter. Isolate
the ADC clock from any digital circuitry with buffers, as with the clock tree shown in Figure 38. The gates used in
the clock tree must be capable of operating at frequencies much higher than those used if added jitter is to be
prevented.
Best performance will be obtained with a differential input drive, compared with a single-ended drive, as
discussed in Single-Ended Operation and Driving the Analog Inputs.
As mentioned in LAYOUT AND GROUNDING, it is good practice to keep the ADC clock line as short as possible
and to keep it well away from any other signals. Other signals can introduce jitter into the clock signal, which can
lead to reduced SNR performance, and the clock can introduce noise into other lines. Even lines with 90°
crossings have capacitive coupling, so try to avoid even these 90° crossings of the clock line.
Figure 38. Isolating the ADC Clock from other Circuitry with a Clock Tree
24
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
ADC14L040
www.ti.com
SNAS311B –JUNE 2005–REVISED APRIL 2013
COMMON APPLICATION PITFALLS
Driving the inputs (analog or digital) beyond the power supply rails. For proper operation, all inputs should
not go more than 100 mV beyond the supply rails (more than 100 mV below the ground pins or 100 mV above
the supply pins). Exceeding these limits on even a transient basis may cause faulty or erratic operation. It is not
uncommon for high speed digital components (e.g., 74F and 74AC devices) to exhibit overshoot or undershoot
that goes above the power supply or below ground. A resistor of about 47Ω to 100Ω in series with any offending
digital input, close to the signal source, will eliminate the problem.
Do not allow input voltages to exceed the supply voltage, even on a transient basis. Not even during power up or
power down.
Be careful not to overdrive the inputs of the ADC14L040 with a device that is powered from supplies outside the
range of the ADC14L040 supply. Such practice may lead to conversion inaccuracies and even to device
damage.
Attempting to drive a high capacitance digital data bus. The more capacitance the output drivers must
charge for each conversion, the more instantaneous digital current flows through VDR and DR GND. These large
charging current spikes can couple into the analog circuitry, degrading dynamic performance. Adequate
bypassing and maintaining separate analog and digital areas on the pc board will reduce this problem.
Additionally, bus capacitance beyond the specified 15 pF/pin will cause tOD to increase, making it difficult to
properly latch the ADC output data. The result could, again, be an apparent reduction in dynamic performance.
The digital data outputs should be buffered (with 74ACQ541, for example). Dynamic performance can also be
improved by adding series resistors at each digital output, close to the ADC14L040, which reduces the energy
coupled back into the converter output pins by limiting the output current. A reasonable value for these resistors
is 33Ω.
Using an inadequate amplifier to drive the analog input. As explained in Signal Inputs, the capacitance seen
at the input alternates between 11 pF and 4.5 pF, depending upon the phase of the clock. This dynamic load is
more difficult to drive than is a fixed capacitance.
If the amplifier exhibits overshoot, ringing, or any evidence of instability, even at a very low level, it will degrade
performance. A small series resistor at each amplifier output and a capacitor at the analog inputs (as shown in
Figure 37) will improve performance. The LMH6702 and the LMH6628 have been successfully used to drive the
analog inputs of the ADC14L040.
Also, it is important that the signals at the two inputs have exactly the same amplitude and be exactly 180º out of
phase with each other. Board layout, especially equality of the length of the two traces to the input pins, will
affect the effective phase between these two signals. Remember that an operational amplifier operated in the
non-inverting configuration will exhibit more time delay than will the same device operating in the inverting
configuration.
Operating with the reference pins outside of the specified range. As mentioned in Reference Pins, when
using an external reference, VREF should be in the range of
0.8V ≤ VREF ≤ 1.2V
(7)
Operating outside of these limits could lead to performance degradation.
Inadequate network on Reference Bypass pins (VRP, VRN, and VRM). As mentioned in Reference Pins, these
pins should be bypassed with 0.1 µF capacitors to ground, and 10 µF capacitor should be connected between
pins VRP and VRN
.
Using a clock source with excessive jitter, using excessively long clock signal trace, or having other
signals coupled to the clock signal trace. This will cause the sampling interval to vary, causing excessive
output noise and a reduction in SNR and SINAD performance.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: ADC14L040
ADC14L040
SNAS311B –JUNE 2005–REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision A (April 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 25
26
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: ADC14L040
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
ADC14L040CIVY/NOPB
ACTIVE
LQFP
NEY
32
250
RoHS & Green
SN
Level-3-260C-168 HR
-40 to 85
ADC14L0
40CIVY
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jun-2023
TRAY
L - Outer tray length without tabs
KO -
Outer
tray
height
W -
Outer
tray
width
Text
P1 - Tray unit pocket pitch
CW - Measurement for tray edge (Y direction) to corner pocket center
CL - Measurement for tray edge (X direction) to corner pocket center
Chamfer on Tray corner indicates Pin 1 orientation of packed units.
*All dimensions are nominal
Device
Package Package Pins SPQ Unit array
Max
matrix temperature
(°C)
L (mm)
W
K0
P1
CL
CW
Name
Type
(mm) (µm) (mm) (mm) (mm)
ADC14L040CIVY/NOPB
NEY
LQFP
32
250
9 X 24
150
322.6 135.9 7620 12.2
11.1 11.25
Pack Materials-Page 1
PACKAGE OUTLINE
NEY0032A
LQFP - 1.6 mm max height
SCALE 1.800
PLASTIC QUAD FLATPACK
7.1
6.9
B
32
25
PIN 1 ID
24
1
7.1
6.9
9.4
TYP
8.6
17
8
A
9
16
0.27
0.17
OPTIONAL:
SHARP CORNERS EXCEPT
PIN 1 ID CORNER
28X 0.8
4X 5.6
32X
0.2
C A B
SEE DETAIL A
1.6 MAX
C
SEATING PLANE
0.09-0.20
TYP
0.25
GAGE PLANE
(1.4)
0.1
0.15
0.05
0.75
0.45
0 -7
DETAIL
A
S
C
A
L
E
:
1
2
DETAIL A
TYPICAL
4219901/A 10/2016
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC registration MS-026.
www.ti.com
EXAMPLE BOARD LAYOUT
NEY0032A
LQFP - 1.6 mm max height
PLASTIC QUAD FLATPACK
SYMM
25
32
32X (1.6)
1
24
32X (0.4)
SYMM
(8.5)
28X (0.8)
8
17
(R0.05) TYP
9
16
(8.5)
LAND PATTERN EXAMPLE
SCALE:8X
0.07 MAX
ALL AROUND
0.07 MIN
ALL AROUND
METAL
METAL UNDER
SOLDER MASK
SOLDER MASK
SOLDER MASK
OPENING
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4219901/A 10/2016
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
NEY0032A
LQFP - 1.6 mm max height
PLASTIC QUAD FLATPACK
SYMM
25
32
32X (1.6)
1
24
32X (0.4)
SYMM
(8.5)
28X (0.8)
8
17
(R0.05) TYP
16
9
(8.5)
SOLDER PASTE EXAMPLE
SCALE 8X
4219901/A 10/2016
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号:
ADC14V155CISQ/NOPB
IC 1-CH 14-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, QCC48, 7 X 7 MM, 0.80 MM HEIGHT, 0.50 MM PITCH, LEAD FREE, LLP-48, Analog to Digital Converter
NSC
©2020 ICPDF网 联系我们和版权申明