ADC3660IRSBR [TI]
双路、16 位、0.5MSPS 至 65MSPS、低噪声、超低功耗模数转换器 (ADC) | RSB | 40 | -40 to 105;
| 型号： | ADC3660IRSBR |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 双路、16 位、0.5MSPS 至 65MSPS、低噪声、超低功耗模数转换器 (ADC) | RSB | 40 | -40 to 105 转换器 模数转换器 |
| 文件： | 总82页 (文件大小：4796K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ADC3660
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
ADC3660 16 位、0.5 至65 MSPS、低噪声、低功率双通道ADC
1 特性
3 说明
• 双通道
ADC3660 器件是一款低噪声、超低功耗、16 位、
65MSPS 双通道高速模数转换器 (ADC)。该器件可实
现低功耗，噪声频谱密度为 –159dBFS/Hz，还具有出
色的线性度和动态范围。ADC3660 可实现出色的直流
精度以及中频采样支持，因此是各种应用的出色选择。
该 ADC 在 65MSPS 下的功耗仅为每通道 71mW，功
耗随采样率减小而迅速降低。在旁路模式（ 最高
31MSPS）下，您可以在 1 或 2 个时钟周期后获取输
出数据。
• 16 位65MSPS ADC（最大输出速率= 31Msps）
• 本底噪声：-159dBFS/Hz
• 超低功耗：65MSPS 时为每通道71mW
• 16 位，无丢码
• INL：±2LSB；DNL：±0.2LSB
• 基准：外部或内部
• 输入带宽：900MHz (3dB)
• 工业温度范围：-40°C 至+105°C
• 片上数字下变频器
ADC3660 使用串行 CMOS (SCMOS) 接口输出数据，
可更大限度减少数字互连的次数。该器件提供双通道、
单通道和半通道选项。串行 CMOS 接口支持高达
250Mbps 的输出速率，相当于在复杂抽取后大约
15MSPS（双线）到大约 3.75MSPS（0.5 线）的输出
速率。因此，ADC3660 可以使用内部抽取滤波器在
“过采样和抽取”模式下运行，从而改进动态范围并省
去外部抗混叠滤波器。
– 2 倍、4 倍、8 倍、16 倍、32 倍抽取率
– 32 位NCO
• 串行CMOS 接口
• 1.8V 单电源
• 小尺寸: 40 引脚WQFN (5mm × 5mm) 封装
• 频谱性能(fIN = 5MHz)：
– SNR：81.9dBFS
– SFDR：88dBc HD2、HD3
– SFDR：102dBFS 最严重毛刺
该器件采用 40 引脚 WQFN 封装（5mm × 5mm），支
持–40 至+105⁰C 的工业级工作温度范围。
2 应用
器件信息
器件型号(1)
ADC3660
封装尺寸（标称值）
• 数据采集(DAQ)
• 电机诊断和监控
• 电能质量分析仪
• 电源品质测定器
• 声纳
封装
WQFN (40)
5.00 × 5.00mm
(1) 如需了解所有可用封装，请参阅数据表末尾的封装选项附录。
0
AIN = -1 dBFS
SNR = 89.0 dBFS
SFDR = 106 dBc
• 雷达
• 国防无线电
• 无线通信
• 实验室和现场仪表
• 光谱仪
-20
-40
-60
-80
-100
-120
-140
0
1
Input Frequency (MHz)
2
ADC3
FS = 65MSPS，Fin = 1MHz，16 倍抽取，实时
本文档旨在为方便起见，提供有关TI 产品中文版本的信息，以确认产品的概要。有关适用的官方英文版本的最新信息，请访问
www.ti.com，其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前，请务必参考最新版本的英文版本。
English Data Sheet: SBASA01
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
Table of Contents
8.3 Feature Description...................................................22
8.4 Device Functional Modes..........................................45
8.5 Programming............................................................ 47
8.6 Register Maps...........................................................49
9 Application and Implementation..................................66
9.1 Typical Application.................................................... 66
9.2 Initialization Set Up................................................... 69
10 Power Supply Recommendations..............................70
11 Layout...........................................................................72
11.1 Layout Guidelines................................................... 72
11.2 Layout Example...................................................... 72
12 Device and Documentation Support..........................73
12.1 支持资源..................................................................73
12.2 Trademarks.............................................................73
12.3 Electrostatic Discharge Caution..............................73
12.4 术语表..................................................................... 73
13 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 5
6.1 Absolute Maximum Ratings........................................ 5
6.2 ESD Ratings............................................................... 5
6.3 Recommended Operating Conditions.........................5
6.4 Thermal Information....................................................6
6.5 Electrical Characteristics - Power Consumption.........6
6.6 Electrical Characteristics - DC Specifications.............7
6.7 Electrical Characteristics - AC Specifications............. 8
6.8 Timing Requirements................................................10
6.9 Typical Characteristics..............................................12
7 Parameter Measurement Information..........................19
8 Detailed Description......................................................21
8.1 Overview...................................................................21
8.2 Functional Block Diagram.........................................21
Information.................................................................... 73
4 Revision History
注：以前版本的页码可能与当前版本的页码不同
Changes from Revision A (October 2020) to Revision B (March 2022)
Page
• Changed the output clock jitter unit from ps to ps pk-pk in the Timing Requirements......................................10
• Changed the ADC latency CMOS 2-wire NOM value from 1 to 2 and 1/2-wire NOM value from 2 to 1.......... 10
• Changed 图8-3 ............................................................................................................................................... 22
• Added GND symbol to REFGND pin for all voltage reference option diagrams...............................................27
• Added the Output Bit Mapper section...............................................................................................................40
• Added default power up configuration summary 表8-11 .................................................................................47
• Updated power-up initialization diagram 图9-4 with the correct indexing .......................................................69
Changes from Revision * (September 2020) to Revision A (October 2020)
Page
• Added Updated characterization data for tCD and tDV ......................................................................................10
• Added condition to resynch during operation to the SYNC section..................................................................35
• added wait condition of 200000 clock cycles....................................................................................................69
Copyright © 2022 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
5 Pin Configuration and Functions
40
39
38
37
36
35
34
33
32
31
1
2
30
29
28
27
26
25
24
23
22
21
PDN/SYNC
VREF
IOVDD
NC
3
REFGND
REFBUF
AVDD
CLKP
DB5
4
DB6
5
IOGND
DCLK
DA6
6
7
CLKM
8
VCM
DA5
9
RESET
SDIO
NC
GND PAD (backside)
10
IOVDD
11
12
13
14
15
16
17
18
19
20
图5-1. RSB Package, 40-Pin WQFN
(Top View)
表5-1. Pin Descriptions
PIN
I/O
Description
Name
No.
INPUT/REFERENCE
AINP
AINM
BINP
BINM
VCM
VREF
12
13
39
38
8
I
I
Positive analog input, channel A
Negative analog input, channel A
Positive analog input, channel B
Negative analog input, channel B
I
I
O
I
Common-mode voltage output for the analog inputs, 0.95 V
External voltage reference input, 1.6 V
2
1.2V external voltage reference input for use with internal reference buffer. Internal 100 kΩ
pull-up resistor to AVDD. This pin is also used to configure default operating conditions.
REFBUF
4
3
I
I
REFGND
CLOCK
Reference ground input, 0 V
CLKP
6
7
I
I
Positive differential sampling clock input for the ADC
Negative differential sampling clock input for the ADC
CLKM
CONFIGURATION
Power down/Synchronization input. This pin can be configured via the SPI interface. Active
high. This pin has an internal 21 kΩpull-down resistor.
PDN/SYNC
1
I
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
表5-1. Pin Descriptions (continued)
PIN
I/O
Description
Name
RESET
SEN
No.
9
I
I
Hardware reset. Active high. This pin has an internal 21 kΩpull-down resistor.
16
35
10
Serial interface enable. Active low. This pin has an internal 21 kΩpull-up resistor to AVDD.
Serial interface clock input. This pin has an internal 21 kΩpull-down resistor.
SCLK
SDIO
I
I/O
Serial interface data input and output. This pin has an internal 21 kΩpull-down resistor.
17,19,20,22,
29,31,32,34
NC
-
Do not connect
DIGITAL INTERFACE
DA6
24
O
O
O
O
O
I
CMOS data output.
CMOS data output
DA5
23
18
27
28
33
25
FCLK
CMOS frame clock output
CMOS data output.
CMOS data output
DB6
DB5
DCLKIN
DCLK
CMOS bit clock input
CMOS bit clock output
O
POWER SUPPLY
AVDD
5,15,36
I
I
Analog 1.8V power supply
Ground, 0V
11,14,37,40,
PowerPad
GND
IOVDD
IOGND
21,30
26
I
I
1.8V power supply for digital interface
Ground, 0V for digital interface
Copyright © 2022 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
PARAMETER
TEST CONDITIONS
MIN
–0.3
–0.3
–0.3
–0.3
–0.3
MAX
2.1
UNIT
V
Supply voltage range, AVDD, IOVDD
Supply voltage range, GND, IOGND, REFGND
AINP/M, BINP/M, CLKP/M
Voltage applied to
VREF, REFBUF
input pins
0.3
V
2.1
2.1
V
PDN/SYNC, RESET, SCLK, SEN, SDIO, DCLKIN
2.1
Junction temperature, TJ
Storage temperature, Tstg
105
150
°C
°C
–65
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
6.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per ANSI/
ESDA/JEDEC JS-001, all pins(1)
2500
V(ESD)
Electrostatic discharge
V
Charged device model (CDM), per
JEDEC specification JESD22-C101, all
pins(2)
1000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
1.75
1.75
–40
NOM
1.8
MAX
1.85
UNIT
AVDD(1)
V
V
Supply voltage range
IOVDD(1)
1.8
1.85
TA
TJ
Operating free-air temperature
Operating junction temperature
105
°C
°C
105(2)
(1) Measured to GND.
(2) Prolonged use above this junction temperature may increase the device failure-in-time (FIT) rate.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
6.4 Thermal Information
ADC3660
RSB (QFN)
40 Pins
30.7
THERMAL METRIC(1)
UNIT
RΘJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RΘJC(top)
RΘJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
16.4
10.5
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.2
ΨJT
10.5
ΨJB
RΘJC(bot)
2.0
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.5 Electrical Characteristics - Power Consumption
Typical values are over the operating free-air temperature range, at TA = 25°C, full temperature range is TMIN = –40°C to
TMAX = 105°C, ADC sampling rate = 65 MSPS, 50% clock duty cycle, AVDD = IOVDD = 1.8 V, external 1.6 V reference, 5 pF
output load, and –1-dBFS differential input, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
FS = 65 MSPS
IAVDD
Analog supply current
I/O supply current(1)
Power dissipation(1)
FS = 65 MSPS, External reference
8x real decimation, 2-wire CMOS
External reference
64
15
78
20
mA
IIOVDD
PDIS
142
14
178
mW
mA
mA
mA
mA
16x real decimation, 1-wire CMOS
32x real decimation, 1-wire CMOS
32x real decimation, 1/2-wire CMOS
8x complex decimation, 2-wire CMOS
12
13
19
I/O supply current(1)
16x complex decimation, 1-wire
CMOS
IIOVDD
17
15
16
32x complex decimation, 1-wire
CMOS
mA
32x complex decimation, 1/2-wire
CMOS
MISCELLANEOUS
Internal reference, additional analog
3
0.3
0.7
5
supply current
Internal reference buffer, additional
analog supply current
IAVDD
Enabled via SPI
mA
Single ended clock input, reduces
analog supply current by
Default mask settings, internal
reference
Power consumption in global power
down mode
PDIS
mW
Default mask settings, external
reference
9
(1) Measured with a 1 MHz input frequency full-scale sine wave at specified sample rate, with ~ 5 pF loading on each CMOS output pin.
Copyright © 2022 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
6.6 Electrical Characteristics - DC Specifications
Typical values are over the operating free-air temperature range, at TA = 25°C, full temperature range is TMIN = –40°C to
TMAX = 105°C, ADC sampling rate = 65 MSPS, 50% clock duty cycle, AVDD = IOVDD = 1.8 V, external 1.6 V reference, and
–1-dBFS differential input, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DC ACCURACY
No missing codes
PSRR
16
bits
dB
FIN = 1 MHz
50
± 0.2
± 2
DNL
Differential nonlinearity
Integral nonlinearity
Offset error
FIN = 5 MHz
FIN = 5 MHz
-0.5
-4.5
+1
+4.5
130
LSB
INL(1)
LSB
VOS_ERR
VOS_DRIFT
GAINERR
GAINDRIFT
GAINERR
GAINDRIFT
-130
2
LSB
Offset drift over temperature
Gain error
-3.5
0
LSB/ºC
%FSR
ppm/ºC
%FSR
ppm/ºC
LSB
External 1.6V Reference
External 1.6V Reference
Internal Reference
Gain drift over temperature
Gain error
10.3
2.4
Gain drift over temperature
Internal Reference
108.8
1.5
Transition Noise
ADC ANALOG INPUT (AINP/M, BINP/M)
FS
Input full scale
Differential
3.2
0.95
8
Vpp
V
VCM
RIN
Input common model voltage
Differential input resistance
Differential input Capacitance
Output common mode voltage
Analog Input Bandwidth (-3dB)
0.9
1.0
FIN = 100 kHz
FIN = 100 kHz
kΩ
pF
CIN
7
VOCM
BW
0.95
900
V
MHz
INTERNAL VOLTAGE REFERENCE
VREF Internal reference voltage
1.6
8
V
VREF Output Impedance
Ω
REFERENCE INPUT BUFFER (REFBUF)
External reference voltage
1.2
V
EXTERNAL VOLTAGE REFERENCE (VREF)
VREF
External voltage reference
1.6
0.3
5.3
V
Input Current
mA
kΩ
Input impedance
CLOCK INPUT (CLKP/M)
Input clock frequency
0.5
40
65
MHz
Vpp
V
VID
VCM
RIN
CIN
Differential input voltage
Input common mode voltage
1
0.9
5
3.6
Single ended input resistance to common mode.
Single ended input capacitance
kΩ
pF
1.5
50
Clock duty cycle
60
%
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
6.6 Electrical Characteristics - DC Specifications (continued)
Typical values are over the operating free-air temperature range, at TA = 25°C, full temperature range is TMIN = –40°C to
TMAX = 105°C, ADC sampling rate = 65 MSPS, 50% clock duty cycle, AVDD = IOVDD = 1.8 V, external 1.6 V reference, and
–1-dBFS differential input, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DIGITAL INPUTS (RESET, PDN, SCLK, SEN, SDIO)
VIH
VIL
IIH
IIL
High level input voltage
Low level input voltage
High level input current
Low level input current
Input capacitance
1.4
V
0.4
V
90
-90
1.5
150
uA
uA
pF
-150
CI
DIGITAL OUTPUT (SDOUT)
IOVDD
–0.1
VOH
VOL
High level output voltage
Low level output voltage
ILOAD = -400 uA
IOVDD
V
V
ILOAD = 400 uA
0.1
DIGITAL SCMOS OUTPUTS (DA5/6, DB5/6)
Output data rate
250
MHz
V
per CMOS output pin
ILOAD = 400 uA
DCLKIN
IOVDD
–0.1
VOH
VOL
VIH
VIL
High level output voltage
Low level output voltage
High level input voltage
Low level input voltage
IOVDD
IOVDD
0.1
0.1
V
IOVDD
–0.1
V
V
(1) Performance data shown is prior to decimation filtering. With DDC enabled, performance improves by the decimation filtering process.
6.7 Electrical Characteristics - AC Specifications
Typical values are over the operating free-air temperature range, at TA = 25°C, full temperature range is TMIN = –40°C to
TMAX = 105°C, ADC sampling rate = 65 MSPS, 50% clock duty cycle, AVDD = IOVDD = 1.8 V, external 1.6 V reference, and
–1-dBFS differential input, unless otherwise noted
PARAMETER
TEST CONDITIONS
fIN = 1.1 MHz, AIN = -20 dBFS
fIN = 1.1 MHz
MIN
TYP
-159
82.0
81.9
81.2
79.9
77.6
74.6
88.3
89.2
89.3
88.7
86.5
84.3
MAX
UNIT
NSD
Noise Spectral Density
dBFS/Hz
fIN = 5 MHz
77.5
fIN = 10 MHz
SNR(1)
Signal to noise ratio
dBFS
fIN = 20 MHz
fIN = 40 MHz
fIN = 64 MHz
fIN = 1.1 MHz, fNCO = 2.5 MHz
fIN = 5 MHz, fNCO = 5 MHz
fIN = 10 MHz, fNCO = 10 MHz
fIN = 20 MHz, fNCO = 20 MHz
fIN = 40 MHz, fNCO = 40 MHz
fIN = 64 MHz, fNCO = 62.6 MHz
Signal to noise ratio, complex
decimation by 16
SNR
dBFS
Copyright © 2022 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
6.7 Electrical Characteristics - AC Specifications (continued)
Typical values are over the operating free-air temperature range, at TA = 25°C, full temperature range is TMIN = –40°C to
TMAX = 105°C, ADC sampling rate = 65 MSPS, 50% clock duty cycle, AVDD = IOVDD = 1.8 V, external 1.6 V reference, and
–1-dBFS differential input, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN
TYP
80.0
80.9
80.8
78.1
76.2
73.6
13.3
13.3
13.2
13.0
12.6
12.1
83
MAX
UNIT
fIN = 1.1 MHz
fIN = 5 MHz
fIN = 10 MHz
fIN = 20 MHz
fIN = 40 MHz
fIN = 64 MHz
fIN = 1.1 MHz
fIN = 5 MHz
fIN = 10 MHz
fIN = 20 MHz
fIN = 40 MHz
fIN = 64 MHz
fIN = 1.1 MHz
fIN = 5 MHz
fIN = 10 MHz
fIN = 20 MHz
fIN = 40 MHz
fIN = 64 MHz
fIN = 1.1 MHz
fIN = 5 MHz
fIN = 10 MHz
fIN = 20 MHz
fIN = 40 MHz
fIN = 64 MHz
fIN = 1.1 MHz
fIN = 5 MHz
fIN = 10 MHz
fIN = 20 MHz
fIN = 40 MHz
fIN = 64 MHz
76.2
SINAD(1)
ENOB(1)
THD(1)
Signal to noise and distortion ratio
dBFS
12.6
Effective number of bits
bit
81
87
90
Total Harmonic Distortion (First five
harmonics)
dBc
82
81
80
84
83
88
94
dBc
dBc
Spur free dynamic range including
second and third harmonic
SFDR(1)
85
83
84
101
102
99
91
Spur free dynamic range (excluding
HD2 and HD3)
Non HD2,3(1)
dBFS
95
93
87
f1 = 3 MHz, f2 = 4 MHz, AIN = -7 dBFS/
tone
88
90
IMD3
Two tone inter-modulation distortion
dBc
f1 = 10 MHz, f2 = 12 MHz, AIN = -7
dBFS/tone
(1) Performance data shown is prior to decimation filtering. With DDC enabled, performance improves by the decimation filtering process.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
6.8 Timing Requirements
Typical values are over the operating free-air temperature range, at TA = 25°C, full temperature range is TMIN = –40°C to
TMAX = 105°C, ADC sampling rate = 65 MSPS, 50% clock duty cycle, AVDD = IOVDD = 1.8 V, external 1.6 V reference, 5 pF
output load, and –1-dBFS differential input, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN NOM MAX
UNIT
ADC TIMING SPECIFICATIONS
tAD
tA
Aperture Delay
Aperture Jitter
Jitter on DCLKIN
0.85
180
ns
fs
square wave clock with fast edges
tJ
± 50 ps pk-pk
Sampling
Clock
Period
tACQ
Signal acquisition period, Default
Signal conversion period
referenced to sampling clock falling edge
referenced to sampling clock falling edge
-TS/4
tCONV
10
14.6
14.0
1.7
ns
us
Bandgap reference enabled, single ended
clock
Bandgap reference enabled, differential clock
Time to valid data after coming out of power
down. Internal reference.
Bandgap reference disabled, single ended
clock
ms
us
Bandgap reference disabled, differential clock
2.1
Wake up
time
Bandgap reference enabled, single ended
clock
14.6
14.0
1.8
Bandgap reference enabled, differential clock
Time to valid data after coming out of power
down. External 1.6V reference.
Bandgap reference disabled, single ended
clock
ms
ps
Bandgap reference disabled, differential clock
1.7
tS,SYNC
tH,SYNC
Setup time for SYNC input signal
Hold time for SYNC input signal
500
600
Referenced to sampling clock rising edge
Serialized CMOS: 2-wire
Serialized CMOS: 1-wire
Serialized CMOS: 1/2-wire
2
1
ADC
clock
cycles
ADC
Latency
Signal input to data output
1
Real decimation by 2
21
22
23
Output
clock
cycles
Add.
Latency
Complex decimation by 2
Real or complex decimation by 4, 8, 16, 32
Copyright © 2022 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
6.8 Timing Requirements (continued)
Typical values are over the operating free-air temperature range, at TA = 25°C, full temperature range is TMIN = –40°C to
TMAX = 105°C, ADC sampling rate = 65 MSPS, 50% clock duty cycle, AVDD = IOVDD = 1.8 V, external 1.6 V reference, 5 pF
output load, and –1-dBFS differential input, unless otherwise noted
PARAMETER
TEST CONDITIONS
MIN NOM MAX
UNIT
INTERFACE TIMING
Delay between sampling clock falling edge to
DCLKIN falling edge < 2.5ns.
TDCLK = DCLK period
tCDCLK = Sampling clock falling edge to
DCLKIN falling edge
2 +
3 +
4 +
TDCLK TDCLK TDCLK
+
+
+
tCDCLK tCDCLK tCDCLK
Propagation delay: sampling clock falling
edge to DCLK rising edge
tPD
ns
Delay between sampling clock falling edge to
DCLKIN falling edge >= 2.5ns.
TDCLK = DCLK period
tCDCLK = Sampling clock falling edge to
DCLKIN falling edge
2 +
3 +
4 +
tCDCLK tCDCLK tCDCLK
Fout = 10 MSPS, DA/B5,6 = 80 MBPS
Fout = 20 MSPS, DA/B5,6 = 160 MBPS
Fout = 30 MSPS, DA/B5,6 = 240 MBPS
Fout = 5 MSPS, DA/B6 = 80 MBPS
Fout = 10 MSPS, DA/B6 = 160 MBPS
Fout = 15 MSPS, DA/B6 = 240 MBPS
-0.24
-0.29
-0.28
-0.22
-0.27
-0.52
0.10
0.10
0.09
0.11
0.11
0.08
DCLK rising edge to output data delay
2-wire serial CMOS
tCD
ns
DCLK rising edge to output data delay
1-wire serial CMOS
DCLK rising edge to output data delay
1/2-wire serial CMOS
Fout = 5 MSPS, DA6 = 160 MBPS
-0.24
0.1
Fout = 10 MSPS, DA/B5,6 = 80 MBPS
Fout = 20 MSPS, DA/B5,6 = 160 MBPS
Fout = 30 MSPS, DA/B5,6 = 240 MBPS
Fout = 5 MSPS, DA/B6 = 80 MBPS
Fout = 10 MSPS, DA/B6 = 160 MBPS
Fout = 15 MSPS, DA/B6 = 240 MBPS
Fout = 5 MSPS, DA6 = 160 MBPS
12.19 12.36
Data valid, 2-wire serial CMOS
5.93
3.91
6.1
4.07
tDV
12.21 12.39
ns
Data valid, 1-wire serial CMOS
Data valid, 1/2-wire serial CMOS
5.95
3.83
5.36
6.10
4.08
6.13
SERIAL PROGRAMMING INTERFACE (SCLK, SEN, SDIO) - Input
fCLK,SCLK Serial clock frequency
20
MHz
ns
tS,SEN
tH,SEN
tS,SDIO
tH,SDIO
SEN falling edge to SCLK rising edge
SCLK rising edge to SEN rising edge
SDIO setup time from rising edge of SCLK
SDIO hold time from rising edge of SCLK
10
9
17
9
SERIAL PROGRAMMING INTERFACE (SDIO) - Output
Delay from falling edge of 16th SCLK cycle during read operation for SDIO transition from
tri-state to valid data
tOZD
3.9
10.8
ns
tODZ
tOD
Delay from SEN rising edge for SDIO transition from valid data to tri-state
Delay from falling edge of 16th SCLK cycle during read operation to SDIO valid
3.4
3.9
14
10.8
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
6.9 Typical Characteristics
Typical values at TA = 25 °C, ADC sampling rate = 65 MSPS, AIN = –1 dBFS differential input, 50% clock duty
cycle, AVDD = IOVDD = 1.8 V, external 1.6 V reference, 5 pF output load, unless otherwise noted.
0
-20
0
-20
-40
-40
-60
-60
-80
-80
-100
-120
-140
-100
-120
-140
0
10
20
Input Frequency (MHz)
30
0
10
20
Input Frequency (MHz)
30
D01_
D02_
DECIMATION BYPASS1
AIN = –20 dBFS, DECIMATION BYPASS1
图6-1. Single Tone FFT at FIN = 1.1 MHz
图6-2. Single Tone FFT at FIN = 1.1 MHz
0
0
-20
-20
-40
-60
-40
-60
-80
-80
-100
-120
-140
-100
-120
-140
0
10
20
Input Frequency (MHz)
30
0
10
20
Input Frequency (MHz)
30
D03_
D004
DECIMATION BYPASS1
DECIMATION BYPASS1
图6-4. Single Tone FFT at FIN = 40 MHz
图6-3. Single Tone FFT at FIN = 10 MHz
1
Decimation bypass mode is for full Nyquist zone illustration only.
Copyright © 2022 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
0
-20
0
-20
-40
-40
-60
-60
-80
-80
-100
-120
-100
-120
-140
-140
0
10
20
Input Frequency (MHz)
30
0
10
20
Input Frequency (MHz)
30
D005
D006
AIN = -7 dBFS/tone, DECIMATION BYPASS1
AIN = -20 dBFS/tone, DECIMATION BYPASS1
图6-5. Two Tone FFT at FIN = 3,4 MHz
图6-6. Two Tone FFT at FIN = 3,4 MHz
0
-20
0
-20
-40
-40
-60
-60
-80
-80
-100
-120
-140
-100
-120
-140
0
1
Input Frequency (MHz)
2
0
10
20
Input Frequency (MHz)
30
D08_
D007
AIN = -7 dBFS/tone, DECIMATION BYPASS1
Decimation by 16, real
图6-8. Single Tone FFT at FIN = 1 MHz
图6-7. Two Tone FFT at FIN = 10,12 MHz
0
85
83
81
79
77
75
110
105
100
95
SNR, ext REF
SFDR, ext REF
Non HD23, ext REF
SNR, int REF
SFDR, int REF
Non HD23, int REF
-20
-40
-60
-80
90
-100
-120
85
73
0
80
60 65
-140
-1.05625
10
20
30
40
Input Frequency (MHz)
50
0
Input Frequency (MHz)
1.05625
D14_
D09_
DECIMATION BYPASS1
Decimation by 32, complex. NCO = 10.1 MHz
图6-10. AC Performance vs Input Frequency
图6-9. Single Tone FFT at FIN = 10 MHz
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
13.2
13
83.5
83
120
105
90
Ext REF
Int REF
SNR
SFDR
Non HD23
12.8
12.6
12.4
12.2
12
82.5
82
75
81.5
81
60
45
80.5
30
11.8
80
-80
15
0
0
10
20
30 40
Input Frequency (MHz)
50
60
70
-70
-60
-50
-40
-30
Input Amplitude (dBFS)
-20
-10
D15_
D18_
DECIMATION BYPASS1
FIN = 5 MHz, DECIMATION BYPASS1
图6-11. ENOB vs Input Frequency
图6-12. AC Performance vs Input Amplitude
83
82.5
82
110
83
82.5
82
105
100
95
SNR (dBFS)
SFDR (dBc)
Non HD23 (dBc)
SNR (dBFS), FIN = 5 MHz
SFDR (dBc), FIN = 5 MHz
SNR (dBFS), FIN = 10 MHz
SFDR (dBc), FIN = 10 MHz
105
100
95
81.5
81
81.5
81
90
90
85
80.5
85
80
80
80.5
80
10 15 20 25 30 35 40 45 50 55 60 65
ADC Sampling Rate FS (MSPS)
0
0.5
1
1.5
2
Clock Amplitude (Vpp)
2.5
3
D20_
D21_
FIN = 5 MHz, DECIMATION BYPASS1
DECIMATION BYPASS1
图6-13. AC Performance vs Sampling Rate
图6-14. AC Performance vs Clock Amplitude
84
82
80
78
100
83
82.5
82
105
100
95
SNR
SFDR
SNR
SINAD
SFDR
Non HD23
95
81.5
81
90
90
85
85
80.5
80
35
40
45
50 55
Clock Duty Cycle (%)
60
65
70
1.7
1.75
1.8
AVDD (V)
1.85
1.9
D35_
D28_
FIN = 5 MHz, DECIMATION BYPASS1
FIN = 5 MHz, DECIMATION BYPASS1
图6-15. AC Performance vs Clock Duty cycle
图6-16. AC Performance vs AVDD
Copyright © 2022 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
13.5
83
82.5
82
110
65 MSPS
25 MSPS
SNR, -40èC
SNR, 25èC
SNR, 105èC
SFDR, -40èC
SFDR, 25èC
SFDR, 105èC
105
100
95
13.25
81.5
81
90
80.5
85
13
1.7
80
0.9
80
1.75
1.8
AVDD (V)
1.85
1.9
0.925
0.95
VCM (V)
0.975
1
D30_
D33_
FIN = 5 MHz, DECIMATION BYPASS1
FIN = 5 MHz, DECIMATION BYPASS1
图6-17. ENOB vs AVDD
图6-18. AC Performance vs VCM vs Temperature
30
20
10
3
Ext REF
Int REF
26.7%
25.5%
2
1
13.4%
12.7%
0
9.8%
-1
-2
-3
7.5%
1.9%
1.1%
0.8%
0.6%
0
32765
32767
32769 32771
Output Code
32773
32775
0
8192 16384 24576 32768 40960 49152 57344 65536
Code
D44_
D038
DECIMATION BYPASS1
FIN = 5 MHz, DECIMATION BYPASS1
图6-19. DC Offset Histogramm
图6-20. INL vs Code
0
0.5
Ext Ref
Int Ref
-20
-40
0.25
-60
0
-80
-100
-120
-140
-0.25
-0.5
0
5
Input Frequency (MHz)
10
12.5
D10_
0
16384
32768
Code
49152
65536
FS = 25 MSPS, DECIMATION BYPASS1
D040
FIN = 5 MHz, DECIMATION BYPASS1
图6-22. Single Tone FFT at FIN = 1.1 MHz
图6-21. DNL vs Code
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
0
-20
0
-20
-40
-40
-60
-60
-80
-80
-100
-120
-140
-100
-120
-140
0
5
Input Frequency (MHz)
10
12.5
0
5
Input Frequency (MHz)
10
12.5
D11_
D12_
FS = 25 MSPS, DECIMATION BYPASS1
FS = 25 MSPS, AIN = –20 dBFS, DECIMATION BYPASS1
图6-24. Single Tone FFT at FIN = 10 MHz
图6-23. Single Tone FFT at FIN = 1.1 MHz
0
86
85
84
83
82
81
80
110
105
100
95
SNR
SFDR
Non HD2,3
-20
-40
-60
-80
-100
-120
-140
90
85
0
1
Input Frequency (MHz)
1.5625
80
20
0
5
10
Input Frequency (MHz)
15
D13_
FS = 25 MSPS, Decimation by 8, real
D16_
FS = 25 MSPS, DECIMATION BYPASS1
图6-25. Single Tone FFT at FIN = 1 MHz
图6-26. AC Performance vs Input Frequency
13.5
83.5
120
100
80
SNR
SFDR
Non HD23
83
13.25
82.5
82
60
13
81.5
81
40
12.75
20
0
5
10
Input Frequency (MHz)
15
20
-80
-70
-60
-50
-40
-30
Input Amplitude (dBFS)
-20
-10
0
D17_
D19_
FS = 25 MSPS, DECIMATION BYPASS1
FS = 25 MSPS, FIN = 5 MHz, DECIMATION BYPASS1
图6-27. ENOB vs Input Frequency
图6-28. AC Performance vs Input Amplitude
Copyright © 2022 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
84.5
83.5
82.5
81.5
80.5
79.5
78.5
115
110
105
100
95
84
83.5
83
110
SNR, FIN = 5 MHz
SFDR, FIN = 5 MHz
SNR, FIN = 10 MHz
SFDR, FIN = 10 MHz
SNR
SINAD
SFDR
Non HD23
105
100
95
82.5
82
90
90
85
77.5
0
80
81.5
85
1.9
0.5
1
Clock Amplitude (Vpp)
1.5
2
2.5
3
1.7
1.75
1.8
AVDD (V)
1.85
D22_
D29_
FS = 25 MSPS, FIN = 5 MHz, DECIMATION BYPASS1
FS = 25 MSPS, FIN = 5 MHz, DECIMATION BYPASS1
图6-29. AC Performance vs Clock Amplitude
图6-30. AC Performance vs AVDD
83.5
110
105
100
95
3
2
SNR (dBFS), -40èC
SNR (dBFS), 25èC
SNR (dBFS), 105èC
SFDR (dBc), -40èC
SFDR (dBc), 25èC
SFDR (dBc), 105èC
Ext REF
Int REF
83
82.5
82
1
0
81.5
81
90
-1
-2
85
80.5
80
-3
0
0.9
0.925
0.95
VCM (V)
0.975
1
8192 16384 24576 32768 40960 49152 57344 65536
Code
D34_
D039
FS = 25 MSPS, FIN = 5 MHz, DECIMATION BYPASS1
FS = 25 MSPS, FIN = 5 MHz, DECIMATION BYPASS1
图6-31. AC Performance vs VCM vs Temperature
图6-32. INL vs Code
0.5
110
105
100
95
ChA Victim
ChB Victim
Ext REF
Int REF
0.25
0
90
-0.25
-0.5
85
80
0
10 20 30 40 50 60 70 80 90 100 110 120
Input Frequency (MHz)
0
16384
32768
Code
49152
65536
D37_
D041
Aggressor at -1 dBFS
FS = 25 MSPS, FIN = 5 MHz, DECIMATION BYPASS1
图6-34. Isolation vs Input Frequency
图6-33. DNL vs Code
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
55
50
45
40
35
30
70
60
50
40
30
20
IAVDD
IIOVDD, 2-wire
IIOVDD, 1-wire
IIOVDD, 1/2-wire
15
10
5
0
0.05 0.1
1
10
100
5
10 15 20 25 30 35 40 45 50 55 60 65
Sampling Rate FS (MSPS)
Frequency of Signal on AVDD (MHz)
FIN = 5 MHz, 50 mVpp signal on AVDD
图6-35. PSRR vs Frequency
D42_
D046
FIN = 1 MHz, 32x complex decimation, 16-bit resolution
图6-36. Current vs Sampling Rate
25
16
14
12
10
8
Bypass
/4 real
/8 real
/32 real
/2 real
CL = 5 pF
CL = 10 pF
CL = 15 pF
CL = 22 pF
/4 complex
/8 complex
/32 complex
20
15
10
5
6
4
0
2
5
10 15 20 25 30 35 40 45 50 55 60 65
Sampling Rate (MSPS)
5
10 15 20 25 30 35 40 45 50 55 60 65
Sampling Rate (MSPS)
D47_
D48_
FIN = 1 MHz, 16-bit resolution, 2-w
FIN = 1 MHz, 32x complex decimation, 16-bit resolution, 2-w
图6-37. IIOVDD Current vs Decimation
图6-38. IIOVDD Current vs Load Capacitance
Copyright © 2022 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
7 Parameter Measurement Information
Sample N
Sample N+1
Input Signal
tAD
tPD
Sampling
Clock
tACQ
tConv
tCDCLK
DCLKIN
DCLK
TDCLK
tCD
FCLK
tDV
DA5/DB5
(MSB)
D15 D13 D11 D9
D7 D5 D3 D1 D15 D13 D11 D9
D7
D6
D5
D4
D3
D2
D1
D0
DA6/DB6
D14 D12 D10 D8
(LSB)
D6 D4 D2 D0 D14 D12 D10 D8
Sample N-2
Sample N-1
图7-1. Timing diagram: 2-wire SCMOS (changed from 18-bit to 16-bit output after power up)
Sample N
Sample N+1
Input Signal
tAD
tPD
Sampling
Clock
tACQ
tConv
tCDCLK
DCLKIN
DCLK
FCLK
TDCLK
tCD
tDV
DA6
DB6
D2
D1
D0 D15 D14 D13 D12 D11 D10 D9 D8
D0 D15 D14 D13 D12 D11 D10 D9 D8
D7
D7
D6
D6
D5 D4
D5 D4
D3
D3
D2
D2
D1
D1
D0
D0
D2
D1
Sample N-2
Sample N-1
图7-2. Timing diagram: 1-wire SCMOS (changed from 18-bit to 16-bit output after power up)
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
Sample N
Sample N+1
Input Signal
tAD
tPD
Sampling
Clock
tACQ
tCDCLK
tConv
DCLKIN
DCLK
FCLK
tCD
TDCLK
tDV
Channel A
Channel B
D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
DA6
Sample N-2
Sample N-1
图7-3. Timing diagram: 1/2-wire SCMOS (changed from 18-bit to 16-bit output after power up)
Copyright © 2022 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8 Detailed Description
8.1 Overview
The ADC3660 is a low noise, ultra-low power 16-bit high-speed dual channel ADC family supporting sampling
rates up to 65Msps. It offers excellent DC precision together with IF sampling support which makes it ideally
suited for a wide range of applications. The ADC3660 is equipped with an internal reference option but it also
supports the use of an external, high precision 1.6V voltage reference or an external 1.2V reference which is
buffered and gained up internally.
An optional programmable digital down converter enables external anti-alias filter relaxation as well as output
data rate reduction. The digital filter provides a 32-bit programmable NCO and supports both real or complex
decimation.
备注
The ADC3660 uses a serial CMOS (SCMOS) interface to output the data which minimizes the number
of digital interconnects. The device supports a two-lane (2-wire), a one-lane (1-wire) and a half lane
(1/2-wire) interface option. The serialized CMOS interface supports output rates up to 250Mbps which
translates to the following maximum output rates:
• Decimation Bypass Mode: ~ 31 Msps (2-wire) to ~ 8 Msps (0.5-wire)
• Complex Decimation: ~ 15 Msps (2-wire) to ~4 Msps (0.5-wire)
• Real Decimation: ~ 30 Msps (2-wire) to ~ 8 Msps (0.5-wire)
Hence the ADC3660 can be operated in 'oversampling and decimating' mode using the internal decimation filter
in order to improve the dynamic range and relax external anti-aliasing filter.
The ADC3660 includes a digital output formatter which supports output resolutions from 14 to 20-bit.
The device features and control options can be set up either through pin configurations or via SPI register writes.
8.2 Functional Block Diagram
REFBUF
1.2 V REF
Digital Downconverter
NCO
VREF
Crosspoint
Switch
ADC
16bit
N
AIN
DCLKIN
DCLK
FCLK
0.95 V
VCM
Dig I/F
SCMOS
DA5/6
DB5/6
NCO
ADC
16bit
N
BIN
CLK
Control
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3 Feature Description
8.3.1 Analog Input
The analog inputs of ADC3660 are intended to be driven differentially. Both AC coupling and DC coupling of the
analog inputs is supported. The analog inputs are designed for an input common mode voltage of 0.95 V which
must be provided externally on each input pin. DC-coupled input signals must have a common mode voltage that
meets the device input common mode voltage range.
The equivalent input network diagram is shown in 图8-1. All four sampling switches, on-resistance shown in red,
are in same position (open or closed) simultaneously.
AVDD
Sampling Switch
0.32 pF
1 ꢀ
125 ꢀ
2 nH
xINP/
xINM
24 ꢀ
1.4 pF
0.15 pF
0.6 pF
GND
0.6 pF
GND
GND
GND
GND
6.4 pF
7 ꢀ
GND
5 ꢀ
0.7 pF
1.6 pF
GND
GND
GND
图8-1. Equivalent Input Network
8.3.1.1 Analog Input Bandwidth
图 8-2 shows the analog full power input bandwidth of the ADC3660 with a 50 Ω differential termination. The -3
dB bandwidth is approximately 900 MHz and the useful input bandwidth with good AC performance is
approximately 120 MHz.
The equivalent differential input resistance RIN and input capacitance CIN vs frequency are shown in 图8-3.
0
-1
-2
-3
-4
-5
-6
10
100
Input Frequency (MHz)
1000
ADC3
图8-3. Equivant RIN, CIN vs Input Frequency
图8-2. ADC Analog Input Bandwidth Response
Copyright © 2022 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.1.2 Analog Front End Design
The ADC3660 is an unbuffered ADC and thus a passive kick-back filter is recommended to absorb the glitch
from the sampling operation. Depending on if the input is driven by a balun or a differential amplifier with low
output impedance, a termination network may be needed. Additionally a passive DC bias circuit is needed in AC-
coupled applications which can be combined with the termination network.
8.3.1.2.1 Sampling Glitch Filter Design
The front end sampling glitch filter is designed to optimize the SNR and HD3 performance of the ADC. The filter
performance is dependent on input frequency and therefore the following filter designs are recommended for
different input frequency ranges as shown in 图8-4 and 图8-5 (assuming 50 Ωsource impedance).
33 ꢀ
10 ꢀ
180nH
100 pF
Termination
33 ꢀ
180nH
10 ꢀ
图8-4. Sampling glitch filter for input frequencies from DC to 30 MHz
33 ꢀ
10 ꢀ
100pF
120nH
82 pF
150nH
Termination
33 ꢀ
10 ꢀ
100pF
120nH
图8-5. Sampling glitch filter for input frequencies from 30 to 70 MHz
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.1.2.2 Analog Input Termination and DC Bias
Depending on the input drive circuitry, a termination network and/or DC biasing needs to be provided.
8.3.1.2.2.1 AC-Coupling
The ADC3660 requires external DC bias using the common mode output voltage (VCM) of the ADC together
with the termination network as shown in 图 8-6. The termination is located within the glitch filter network. When
using a balun on the input, the termination impedance has to be adjusted to account for the turns ratio of the
transformer. When using an amplifier, the termination impedance can be adjusted to optimize the amplifier
performance.
Glitch Filter
Termination
33 ꢀ
1 uF
10 ꢀ
180nH
25 ꢀ
100 pF
VCM
0.1 …F
25 ꢀ
33 ꢀ
1 uF
VCM
180nH
10 ꢀ
图8-6. AC-Coupling: termination network provides DC bias (glitch filter example for DC - 30 MHz)
8.3.1.2.2.2 DC-Coupling
In DC coupled applications the DC bias needs to be provided from the fully differential amplifier (FDA) using
VCM output of the ADC as shown in 图 8-7. The glitch filter in this case is located between the anti-alias filter
and the ADC. No termination may be needed if amplifier is located close to the ADC or if the termination is part
of the anti-alias filter.
Glitch Filter
33 ꢀ
10 ꢀ
180nH
100 pF
AAF (Anti
Alias Filter)
33 ꢀ
VCM
180nH
10 ꢀ
图8-7. DC-Coupling: DC bias provided by FDA (glitch filter example for DC - 30 MHz)
Copyright © 2022 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.1.3 Auto-Zero Feature
The ADC3660 includes an internal auto-zero front end amplifier circuit which improves the 1/f flicker noise. This
auto-zero feature can be enabled using SPI register writes (register 0x11, D0).
0
-20
-80
-100
-120
-140
-160
Auto-zero DIS
Auto-zero EN
Auto-zero EN
Auto-zero DIS
-40
-60
-80
-100
-120
-140
0
5
Input Frequency (MHz)
10
12.5
0.005
0.1
1
10
Input Frequency (kHz)
100
1000
adc3
adc3
图8-8. FFT at 25 MSPS with input frequency of 5
MHz (auto-zero feature enable vs disable, 4M point
FFT)
图8-9. FFT at 25 MSPS with input frequency of 5
MHz (auto-zero feature enable vs disable, 4M point
FFT)
0
-80
AZ DIS
AZ EN
Auto-zero DIS
Auto-zero EN
-20
-100
-120
-140
-160
-40
-60
-80
-100
-120
-140
0
10
20
Input Frequency (MHz)
30
0.01
0.1
1
10
Input Frequency (MHz)
100
1000
adc3
adc3
图8-10. FFT at 65 MSPS with input frequency of 5
MHz (auto-zero feature enable vs disable, 4M point
FFT)
图8-11. FFT at 65 MSPS with input frequency of 5
MHz (auto-zero feature enabled vs disabled, 4M
point FFT)
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.2 Clock Input
In order to maximize the ADC SNR performance, the external sampling clock should be low jitter and differential
signaling with a high slew rate. This is especially important in IF sampling applications. For less jitter sensitive
applications, the ADC3660 provides the option to operate with single ended signaling which saves additional
power consumption.
8.3.2.1 Single Ended vs Differential Clock Input
The ADC3660 can be operated using a differential or a single ended clock input where the single ended clock
consumes less power consumption. However clock amplitude impacts the ADC aperture jitter and consequently
the SNR. For maximum SNR performance, a large clock signal with fast slew rates needs to be provided.
• Differential Clock Input: The clock input can be AC coupled externally. The ADC3660 provides internal
biasing for that use case.
• ingle Ended Clock Input: This mode needs to be configured using SPI register (0x0E, D2 and D0) or with the
REFBUF pin. In this mode there is no internal clock biasing and thus the clock input needs to be DC coupled
around a 0.9V center. The unused input needs to be AC coupled to ground.
1.8V
CLKP
CLKP
0.9V
0V
+
-
5kO
VCM
0.9V
5kO
CLKM
CLKM
图8-12. External and internal connection using differential (left) and single ended (right) clock input
8.3.2.2 Signal Acquisition Time Adjust
The ADC3660 includes a register (DLL PDN (0x11, D2) which increases the signal acquisition time window for
clock rates below 40 MSPS from 25% to 50% of the clock period. Increasing the sampling time provides a longer
time for the driving amplifier to settle out the signal which can improve the SNR performance of the system.
When powering down the DLL, the acquisition time will track the clock duty cycle (50% is recommended).
表8-1. Acquisition time vs DLL PDN setting
SAMPLING CLOCK FS (MSPS)
DLL PDN (0x11, D2)
ACQUISITION TIME (tACQ)
65
0
1
TS / 4
TS / 2
≤40
TS: Sampling clock period
Copyright © 2022 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.3 Voltage Reference
The ADC3660 provides three different options for supplying the voltage reference to the ADC. An external 1.6V
reference can be directly connected to the VREF input; a voltage 1.2V reference can be connected to the
REFBUF input using the internal gain buffer or the internal 1.2V reference can be enabled to generate a 1.6V
reference voltage. For best performance, the reference noise should be filtered by connecting a 10 uF and a 0.1
uF ceramic bypass capacitor to the VREF pin. The internal reference circuitry of the ADC3660 is shown in 图
8-13.
备注
The voltage reference mode can be selected using SPI register writes or by using the REFBUF pin
(default) as a control pin (节 8.5.1). If the REFBUF pin is not used for configuration, the REFBUF pin
should be connected to AVDD (even though the REFBUF pin has a weak internal pullup to AVDD) and
the voltage reference option has to be selected using the SPI interface.
AINP
AINM
0.95V
VCM
VREF
(1.6V)
x1.33
REFBUF
(1.2V)
VREF1.2
REFGND
图8-13. Different voltage reference options for ADC3660
8.3.3.1 Internal voltage reference
The 1.6V reference for the ADC can be generated internal using the on-chip 1.2V bandgap reference along with
the internal gain buffer. A 10 uF and a 0.1 uF ceramic bypass capacitor (CVREF) should be connected between
the VREF and REFGND pins as close to the pins as possible.
xINP
xINM
0.95V
VCM
VREF
(1.6V)
x1.33
CVREF
REFBUF
(1.6V)
VREF1.2
REFGND
图8-14. Internal reference
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.3.2 External voltage reference (VREF)
For highest accuracy and lowest temperature drift, the VREF input can be directly connected to an external 1.6V
reference. A 10 uF and a 0.1 uF ceramic bypass capacitor (CVREF) should connected between the VREF and
REFGND pins and placed as close to the pins as possible is recommended. The load current from the external
reference is about 1mA.
Note: The internal reference is also used for other functions inside the device, therefore the reference amplifier
should only be powered down in power down state but not during normal operation.
xINP
xINM
0.95V
VCM
VREF
(1.6V)
Reference
1.6V
REFBUF
(1.2V)
x1.33
CVREF
VREF1.2
REFGND
图8-15. External 1.6V reference
8.3.3.3 External voltage reference with internal buffer (REFBUF)
The ADC3660 is equipped with an on-chip reference buffer that also includes gain to generate the 1.6V
reference voltage from an external 1.2V reference. A 10 uF and a 0.1 uF ceramic bypass capacitor (CVREF
)
between the VREF and REFGND pins and a 10 uF and a 0.1 uF ceramic bypass capacitor between the
REFBUF and REFGND pins are recommended. Both capacitors should be placed as close to the pins as
possible. The load current from the external reference is less than 100uA.
xINP
xINM
0.95V
VCM
VREF
(1.6V)
x1.33
REFBUF
(1.2V)
Reference
1.2V
VREF1.2
CREFBUF
CVREF
REFGND
图8-16. External 1.2V reference using internal reference buffer
Copyright © 2022 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.4 Digital Down Converter
The ADC3660 includes an optional on-chip digital down conversion (DDC) decimation filter that can be enabled
via SPI register setting. It supports complex decimation by 2, 4, 8, 16 and 32 using a digital mixer and a 32-bit
numerically controlled oscillator (NCO) as shown in 图8-17. Furthermore it supports a mode with real decimation
where the complex mixer is bypassed (NCO should be set to 0 for lowest power consumption) and the digital
filter acts as a low pass filter.
Internally the decimation filter calculations are performed with a 20-bit resolution in order to avoid any SNR
degradation due to quantization noise limitation. The output formatter truncates to the selected resolution prior to
outputting the data on the digital interface.
NCO
32bit
Filter
I
Q
I
Q
Digital
Interface
N
ADC
SYNC
图8-17. Internal Digital Decimation Filter
8.3.4.1 DDC MUX
The ADC3660 contains a MUX in front of the digital decimation filters which allows ADC ChA to be connected to
DDC ChB and vice versa.
Digital Downconverter
NCO
DDC MUX
N
ADC
NCO
N
ADC
图8-18. DDC MUX
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.4.2 Digital Filter Operation
The complex decimation operation is illustrated with an example in 图 8-19. First the input signal (and the
negative image) are frequency shifted by the NCO frequency as shown on the left. Next a digital filter is applied
(centered around 0 Hz) and the output data rate is decimated - in this example the output data rate FS,OUT = FS/8
with a Nyquist zone of FS/16. During the complex mixing the spectrum (signal and noise) is split into real and
complex parts and thus the amplitude is reduced by 6-dB. In order to compensate this loss, there is a 6-dB
digital gain option in the decimation filter block that can be enabled via SPI write.
Input Signal
(Alias)
Shifted Input
Signal (Alias)
-FIN + FNCO
Shifted Input Signal
Negative Image
Input Signal
Negative Image
Decimation
by 8
FIN + FNCO
0
0
-FS/16
FS/16
FS/2
-FS/2
-FS/2
FS/2
FNCO
NCO Tuning Range
图8-19. Complex decimation illustration
The real decimation operation is illustrated with an example in 图 8-20. There is no frequency shift happening
and only the real portion of the complex digital filter is exercised. The output data rate is decimated - a
decimation of 8 would result in an output data rate FS,OUT = FS/8 with a Nyquist zone of FS/16.
During the real mixing the spectrum (signal and noise) amplitude is reduced by 3-dB. In order to compensate this
loss, there is a 3-dB digital gain option in the decimation filter block that can be enabled via SPI write.
Input Signal
Decimation by
32
Decimation by
16
Decimation by 2
Decimation by 4
Decimation by 8
FS/2
FS/16
FS/8
FS/4
FS/32
FS/64
图8-20. Real decimation illustration
Copyright © 2022 Texas Instruments Incorporated
30
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.4.2.1 FS/4 Mixing with Real Output
In this mode, the output after complex decimation gets mixed with FS/4 (FS = output data rate in this case).
Instead of a complex output with the input signal centered around 0 Hz, the output is transmitted as a real output
at twice the data rate and the signal is centered around FS/4 (Fout/4) as illustrated in 图8-21.
In this example, complex decimation by 8 is used. The output data is transmitted as a real output with an output
rate of Fout = FS'/4 (FS' = ADC sampling rate). The input signal is now centered around FS/4 (Fout/4) or FS'/16.
FIN
FNCO
- FIN + FNCO
-FIN + FNCO + FS/4
/8
FS/4 mix
Fout/4 mix
Complex
Decimation /8
0
0
FS‘/2
FS/16
FS‘/2
FS/8
0
FS/2
图8-21. FS/4 Mixing with real output
8.3.4.3 Numerically Controlled Oscillator (NCO) and Digital Mixer
The decimation block is equipped with a 32-bit NCO and a digital mixer to fine tune the frequency placement
prior to the digital filtering. The oscillator generates a complex exponential sequence of:
ejωn (default) or e–jωn
(1)
where: frequency (ω) is specified as a signed number by the 32-bit register setting
The complex exponential sequence is multiplied with the real input from the ADC to mix the desired carrier to a
frequency equal to fIN + fNCO. The NCO frequency can be tuned from –FS/2 to +FS/2 and is processed as a
signed, 2s complement number. After programming a new NCO frequency, the mixer restart register bits (0x26,
D4/D1) or SYNC pin has to be toggled for the new frequency to get active. Additionally the ADC3660 provides
the option via SPI to invert the mixer phase. The NCO frequency setting is set by the 32-bit register value given
and calculated as:
NCO frequency = 0 to + FS/2: NCO = fNCO × 232 / FS
NCO frequency = -FS/2 to 0: NCO = (fNCO + FS) × 232 / FS
where:
• NCO = NCO register setting (decimal value)
• fNCO = Desired NCO frequency (MHz)
• FS = ADC sampling rate (MSPS)
The NCO programming is further illustrated with this example:
• ADC sampling rate FS = 65 MSPS
• Input signal fIN = 10 MHz
• Desired output frequency fOUT = 0 MHz
For this example there are actually four ways to program the NCO and achieve the desired output frequency as
shown in 表8-2.
表8-2. NCO value calculations example
Alias or negative image
fIN = –10 MHz
fNCO
NCO Value
660764199
3634203097
Mixer Phase
Frequency translation for fOUT
fNCO = 10 MHz
fNCO = –10 MHz
fOUT = fIN + fNCO = –10 MHz +10 MHz = 0 MHz
fOUT = fIN + fNCO = 10 MHz + (–10 MHz) = 0 MHz
as is
fIN = 10 MHz
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
31
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
表8-2. NCO value calculations example (continued)
Alias or negative image
fNCO
NCO Value
Mixer Phase
Frequency translation for fOUT
fIN = 10 MHz
fNCO = 10 MHz
660764199
fOUT = fIN –fNCO = 10 MHz –10 MHz = 0 MHz
inverted
fOUT = fIN –fNCO = –10 MHz –(–10 MHz) = 0
3634203097
fIN = –10 MHz
fNCO = –10 MHz
MHz
Copyright © 2022 Texas Instruments Incorporated
32
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.4.4 Decimation Filter
The ADC3660 supports complex decimation by 2, 4, 8, 16 and 32 with a pass-band bandwidth of ~ 80% and a
stopband rejection of at least 85dB. 表 8-3 gives an overview of the pass-band bandwidth of the different
decimation settings with respect to ADC sampling rate FS. Note that the maximum output rate limits can't be
exceeded and the ADC sampling rate may need to adjusted. In real decimation mode the output bandwidth is
half of the complex bandwidth.
表8-3. Decimation Filter Summary and Maximum Available Output Bandwidth
REAL/COMPLEX
DECIMATION
DECIMATION
SETTING N
OUTPUT
BANDWIDTH
OUTPUT RATE
(FS = 65 MSPS)
OUTPUT BANDWIDTH
(FS = 65 MSPS)
OUTPUT RATE
2
4
FS / 2 complex
FS / 4 complex
FS / 8 complex
FS / 16 complex
FS / 32 complex
FS / 2 real
0.8 × FS / 2
0.8 × FS / 4
0.8 × FS / 8
0.8 × FS / 16
0.8 × FS / 32
0.4 × FS / 2
0.4 × FS / 4
0.4 × FS / 8
0.4 × FS / 16
0.4 × FS / 32
32.5 MSPS complex
16.25 MSPS complex
8.125 MSPS complex
4.0625 MSPS complex
2.03125 MSPS complex
32.5 MSPS
26 MHz
13 MHz
Complex
8
6.5 MHz
16
32
2
3.25 MHz
1.625 MHz
13 MHz
4
FS / 4 real
16.25 MSPS
6.5 MHz
Real
8
FS / 8 real
8.125 MSPS
3.25 MHz
1.625 MHz
0.8125 MHz
16
32
FS / 16 real
4.0625 MSPS
FS / 32 real
2.03125 MSPS
The decimation filter responses normalized tot he ADC sampling clock frequency FS are illustrated in 图 8-23 to
图8-32. They are interpreted as follows:
Each figure contains the filter pass-band, transition band(s) and alias or stop-band(s) as shown in 图 8-22. The
x-axis shows the offset frequency (after the NCO frequency shift) normalized to the ADC sampling rate FS.
For example, in the divide-by-4 complex setup, the output data rate is FS / 4 complex with a Nyquist zone of FS /
8 or 0.125 × FS. The transition band (colored in blue) is centered around 0.125 × FS and the alias transition band
is centered at 0.375 × FS. The stop-bands (colored in red), which alias on top of the pass-band, are centered at
0.25 × FS and 0.5 × FS. The stop-band attenuation is greater than 85 dB.
0
Passband
Transition Band
-20
Alias Band
Attn Spec
Filter
-40
-60
Transition
Bands
Bands that alias on top
of signal band
Pass Band
-80
-100
-120
0
0.1
0.2
0.3
0.4
0.5
Normalized Frequency (Fs)
图8-22. Interpretation of the Decimation Filter Plots
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
33
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
0
0.1
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
Passband
Passband
Transition Band
Alias Band
Attn Spec
Transition Band
Alias Band
Attn Spec
-20
-40
-60
-0.01
-0.02
-0.03
-0.04
-0.05
-0.06
-0.07
-0.08
-0.09
-0.1
-80
-100
-120
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0
0.025 0.05 0.075
0.1
0.125 0.15 0.175
0.2
0.225 0.25
Normalized Frequency (Fs)
Normalized Frequency (Fs)
Decb
Decb
图8-23. Decimation by 2 complex frequency
图8-24. Decimation by 2 complex passband ripple
response
response
0
0
Passband
Transition Band
Alias Band
Passband
Transition Band
Alias Band
Attn Spec
-0.01
-0.02
-20
-40
Attn Spec
-0.03
-0.04
-0.05
-0.06
-0.07
-0.08
-0.09
-0.1
-60
-80
-100
-120
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0
0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 0.11 0.12
Normalized Frequency (Fs)
Normalized Frequency (Fs)
Decb
Decb
图8-25. Decimation by 4complex frequency
图8-26. Decimation by 4 complex passband ripple
response
response
0
-0.08
Passband
Transition Band
Alias Band
Passband
-0.081
-0.082
-0.083
-0.084
-0.085
-0.086
-0.087
-0.088
-0.089
-0.09
Transition Band
Alias Band
Attn Spec
-20
-40
Attn Spec
-60
-0.091
-0.092
-0.093
-0.094
-0.095
-0.096
-0.097
-0.098
-0.099
-0.1
-80
-100
-120
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0
0.006 0.012 0.018 0.024 0.03 0.036 0.042 0.048 0.054 0.06
Normalized Frequency (Fs)
Normalized Frequency (Fs)
Decb
Decb
图8-27. Decimation by 8 complex frequency
图8-28. Decimation by 8 complex passband ripple
response
response
Copyright © 2022 Texas Instruments Incorporated
34
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
0
-0.1
-0.11
-0.12
-0.13
-0.14
-0.15
-0.16
-0.17
-0.18
-0.19
-0.2
Passband
Passband
Transition Band
Alias Band
Attn Spec
Transition Band
Alias Band
Attn Spec
-20
-40
-60
-80
-100
-120
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0
0.003 0.006 0.009 0.012 0.015 0.018 0.021 0.024 0.027 0.03
Normalized Frequency (Fs)
Normalized Frequency (Fs)
Decb
Decb
图8-29. Decimation by 16 complex frequency
图8-30. Decimation by 16 complex passband
response
ripple response
0
-0.2
Passband
Transition Band
Alias Band
Passband
Transition Band
Alias Band
Attn Spec
-0.205
-0.21
-20
-40
Attn Spec
-0.215
-0.22
-60
-0.225
-0.23
-80
-0.235
-0.24
-100
-120
-0.245
-0.25
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
0
0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016 0.018 0.02
Normalized Frequency (Fs)
Normalized Frequency (Fs)
Decb
Decb
图8-31. Decimation by 32 complex frequency
图8-32. Decimation by 32 complex passband
response
ripple response
8.3.4.5 SYNC
The PDN/SYNC pin can be used to synchronize multiple devices using an external SYNC signal. The PDN/
SYNC pin can be configured via SPI (SYNC EN bit) from power down to synchronization functionality and is
latched in by the rising edge of the sampling clock as shown in 图8-33.
CLK
tS,SYNC
tH,SYNC
SYNC
图8-33. External SYNC timing diagram
The synchronization signal is only required when using the decimation filter - either using the SPI SYNC register
or the PDN/SYNC pin. It resets internal clock dividers used in the decimation filter and aligns the internal clocks
as well as I and Q data within the same sample. If no SYNC signal is given, the internal clock dividers is not be
synchronized, which can lead to a fractional delay across different devices. The SYNC signal also resets the
NCO phase and loads the new NCO frequency (same as the MIXER RESTART bit).
When trying to resynchronize during operation, the SYNC toggle should occur at 64*K clock cycles, where K is
an integer. This ensures phase continuity of the clock divider.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
35
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.4.6 Output Formatting with Decimation
When using decimation, the output data is formatted as shown in 图8-34 (complex decimation) and 图8-35 (real
decimation). The interface data rates for 2-, 1- and 1/2-wire for complex output for different decimation settings
are shown in 表8-4.
FCLK
AI
AI
AI
D15 D13 D11
AI
D9
AI
D7
AI
D5
AI
D3
AI
D1
AQ AQ
D13 D11
AQ
D9
AQ
D7
AQ
D5
AQ
D3
AQ
D1
AQ
D15
DA5
DA6
DB5
AI AI
D14 D12 D10
AI
AI
D8
AI
D6
AI
D4
AI
D2
AI
D0
AQ AQ
D12 D10
AQ
D8
AQ
D6
AQ
D4
AQ
D2
AQ
D0
AQ
D14
BI BI
D15 D13 D11
BI
BI
D9
BI
D7
BI
D5
BI
D3
BI
D1
BQ BQ
D13 D11
BQ
D9
BQ
D7
BQ
D5
BQ
D3
BQ
D1
BQ
D15
2-Wire
8x Serialization
BI
BI
BI
D14 D12 D10
BI
D8
BI
D6
BI
D4
BI
D2
BI
D0
BQ BQ
D12 D10
BQ
D8
BQ
D6
BQ
D4
BQ
D2
BQ
D0
BQ
D14
DB6
DCLK
FCLK
1-Wire
16x Serialization
DA6
DB6
AI <15:0>
BI <15:0>
AQ <15:0>
BQ <15:0>
DCLK
FCLK
DA6
1/2-Wire
(32x Serialization)
AI <15:0>
BI <15:0>
AQ <15:0>
BQ <15:0>
DCLK
图8-34. Output Data Format in Complex Decimation
表 8-4 illustrates the output interface data rate along with the corresponding DCLK/DCLKIN and FCLK
frequencies based on output resolution (R), number of SCMOS lanes (L) and complex decimation setting (N).
Furthermore the table shows an actual lane rate example for the 2-, 1- and 1/2-wire interface, 16-bit output
resolution and complex decimation by 16.
表8-4. Serial CMOS Lane Rate Examples with Complex Decimation
DECIMATION
SETTING
ADC SAMPLING
RATE
OUTPUT
RESOLUTION
# of WIRES
FCLK
DCLKIN, DCLK
DA/B5,6
N
FS
R
L
2
FS / N
[DA/B5,6] / 2
32.5 MHz
65 MHz
FS x 2 x R / L / N
65 MHz
65 MSPS
62.5 MSPS
4..0625 MHz
3.90625 MHz
16
16
1
130 MHz
1/2
125 MHz
250 MHz
Copyright © 2022 Texas Instruments Incorporated
36
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
FCLK
DA5
DA6
DB5
DB6
DCLK
A0
A0
A0
A0
D9
A0
D7
A0
D5
A0
D3
A0
D1
A1
A1
A1
D11
A1
D9
A1
D7
A1
D5
A1
D3
A1
D1
D15 D13 D11
D15 D13
A0 A0
D14 D12 D10
A0
A0
D8
A0
D6
A0
D4
A0
D2
A0
D0
A1 A1
D14 D12 D10
A1
A1
D8
A1
D6
A1
D4
A1
D2
A1
D0
B0
B0
B0
B0
D9
B0
D7
B0
D5
B0
D3
B0
D1
B1
B1
B1
D11
B1
D9
B1
D7
B1
D5
B1
D3
B1
D1
D15 D13 D11
D15 D13
2-Wire
8x Serialization
B0
B0
B0
B0
D8
B0
D6
B0
D4
B0
D2
B0
D0
B1
B1
B1
B1
D8
B1
D6
B1
D4
B1
D2
B1
D0
D14 D12 D10
D14 D12 D10
FCLK
1-Wire
16x Serialization
DA6
DB6
A0 <15:8>
B0 <15:8>
A1 <7:0>
B1 <7:0>
DCLK
FCLK
DA6
1/2-Wire
(32x Serialization)
A0 <15:0>
B0 <15:0>
DCLK
图8-35. Output Data Format in Real Decimation
表 8-5 illustrates the output interface data rate along with the corresponding DCLK/DCLKIN and FCLK
frequencies based on output resolution (R), number of SCMOS lanes (L) and real decimation setting (M).
Furthermore the table shows an actual lane rate example for the 2-, 1- and 1/2-wire interface, 16-bit output
resolution and real decimation by 16.
表8-5. Serial CMOS Lane Rate Examples with Real Decimation
DECIMATION
SETTING
ADC SAMPLING
RATE
OUTPUT
RESOLUTION
# of WIRES
FCLK
DCLKIN, DCLK
DA/B5,6
FS / M / 2 (L = 2)
FS / M (L = 1, 1/2)
M
FS
R
L
[DA/B5,6] / 2
FS x R / L / M
2
1
2.03125 MHz
16.25 MHz
32.5 MHz
65 MHz
32.5 MHz
65 MHz
16
65 MSPS
16
4.0625 MHz
1/2
130 MHz
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
37
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.5 Digital Interface
The serial CMOS interface supports the data output with 2-wire, 1-wire and 1/2-wire operation. The actual data
output rate depends on the output resolution and number of lanes used.
The ADC3660 requires an external serial clock input (DCLKIN), which is used to transmit the data out of the
ADC along with the data clock (DCLK). The phase relationship between DCLKIN and the sampling clock is
irrelevant but both clocks need to be frequency locked. The serial CMOS interface is configured using SPI
register writes.
8.3.5.1 SDR Output Clocking
The ADC3660 provides a SDR output clocking option which is enabled using the SPI interface. By default the
data is output on rising and falling edge of DCLK. In SDR clocking mode, DCLKIN has to be twice as fast as the
default DCLKIN so that the output data are clocked out only on DCLK rising edge. This SDR clock option is
available in all output modes including decimation.
Internally DCLKIN is divided by 2 for data processing and this operation can add 1 extra clock cycle latency to
the ADC latency.
Latency (2 clock cycles)
Sample N+1
Sample N+2
Sample N
Sample N+3
Sample N+6
Sample N+4
Sample N+5
tAD
tPD
Continous
Clock
DCLKIN
DCLKIN
SDR
DCLK
DCLK
SDR
tCD
FCLK
DA/B5
(MSB)
DA/B6
(LSB)
Sample N-1
Sample N
Sample N+1
Sample N+2
图8-36. SDR Output Clocking
Copyright © 2022 Texas Instruments Incorporated
38
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.5.2 Output Data Format
The output data can be configured to two's complement (default) or offset binary formatting using SPI register
writes (register 0x8F and 0x92). 表 8-6 provides an overview for minimum and maximum output codes for the
two formatting options. The actual output resolution is set by the output bit mapper.
表8-6. Overview of minimum and maximum output codes vs output resolution for different formatting
Two's Complement (default)
Offset Binary
RESOLUTION (BIT)
14
16
18
20
14
16
18
20
VIN,MAX
0
0x1FFF
0x7FFF
0x1FFFF
0x7FFFF
0x3FFF
0x2000
0xFFFF
0x8000
0x3FFFF
0x20000
0xFFFFF
0x80000
0x0000
0x2000
0x00000
VIN,MIN
0x8000
0x20000
0x80000
0x0000
0x00000
8.3.5.3 Output Formatter
The digital output interface utilizes a flexible output bit mapper as shown in 图8-37. The bit mapper takes the 16-
bit output directly from the ADC or from digital filter block and reformats it to a resolution of 14,16,18 or 20-bit.
The output serialization factor gets adjusted accordingly for 2-, 1- and 1/2-wire interface mode. The maximum
output data rate can not be exceeded independently of output resolution and serialization factor.
备注
After power up the bit mapper output defaults to 18-bit and manually has to be programmed to 16-bit.
See 节8.3.5.5 for instructions.
For 14-bit the LSBs simply get truncated during the reformatting. With 18 and 20-bit output, bypass or
decimation mode has 0s for the two LSBs while only the digital averaging mode utilizes the full 20-bit output.
DIG
I/F
Output
Formatter
14/16/18/
20-bit
NCO
TEST
Output
Bit Mapper
PATTERN
N
图8-37. Interface output bit mapper
表 8-7 provides an overview for the resulting serialization factor depending on output resolution and output
modes. Note that the DCLKIN frequency needs to be adjusted accordingly as well. Changing the output
resolution to 18-bit, 2-wire mode for example would result in DCLKIN = FS * 4.5 instead of * 4.
表8-7. Serialization factor vs output resolution for different output modes
OUTPUT RESOLUTION
Interface
SERIALIZATION
FCLK
FS/2
FS
DCLKIN
FS* 3.5
FS* 7
DCLK
FS* 3.5
FS* 7
DA/B5,6
FS* 7
2-Wire
7x
14-bit
1-Wire
14x
28x
8x
FS* 14
FS* 28
FS* 8
1/2-Wire
2-Wire
FS
FS* 14
FS* 4
FS* 14
FS* 4
FS/2
FS
16-bit
18-bit (default)
20-bit
1-Wire
16x
32x
9x
FS* 8
FS* 8
FS* 16
FS* 32
FS* 9
1/2-Wire
2-Wire
FS
FS* 16
FS* 4.5
FS* 9
FS* 16
FS* 4.5
FS* 9
FS/2
FS
1-Wire
18x
36x
10x
20x
40x
FS* 18
FS* 36
FS* 10
FS* 20
FS* 40
1/2-Wire
2-Wire
FS
FS* 18
FS* 5
FS* 18
FS* 5
FS/2
FS
1-Wire
FS* 10
FS* 20
FS* 10
FS* 20
1/2-Wire
FS
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
39
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
The programming sequence to change the output interface and/or resolution from default settings is shown in 节
8.3.5.5.
8.3.5.4 Output Bit Mapper
The output bit mapper allows to change the output bit order for any selected interface mode.
DIG
I/F
Output
Formatter
14/16/18/
20-bit
NCO
TEST
Output
Bit Mapper
PATTERN
N
图8-38. Output Bit Mapper
It is a two step process to change the output bit mapping and assemble the output data bus:
1. Both channel A and B can have up to 20-bit output. Each output bit of either channel has a unique identifier
bit as shown in the 表8-8. The MSB starts with bit D19 –depending on output resolution chosen the LSB
would be D6 (14-bit) to D0 (20-bit). The ‘previous sample’is only needed in 2-w mode.
2. The bit mapper is then used to assemble the output sample. The following sections detail how to remap the
serial output format.
表8-8. Unique identifier of each data bit
Bit
Channel A
Channel B
Previous sample (2w only)
Current sample
0x6D
0x6C
0x67
Previous sample (2w only)
Current sample
0x69
D19 (MSB)
D18
D17
D16
D15
D14
D13
D12
D11
D10
D9
0x2D
0x2C
0x27
0x26
0x25
0x24
0x1F
0x1E
0x1D
0x1C
0x17
0x16
0x15
0x14
0x0F
0x0E
0x0D
0x0C
0x07
0x06
0x29
0x28
0x23
0x22
0x21
0x20
0x1B
0x1A
0x19
0x18
0x13
0x12
0x11
0x10
0x0B
0x0A
0x09
0x08
0x03
0x02
0x68
0x63
0x66
0x62
0x65
0x61
0x64
0x60
0x5F
0x5B
0x5A
0x59
0x5E
0x5D
0x5C
0x57
0x58
0x53
D8
0x56
0x52
D7
0x55
0x51
D6
0x54
0x50
D5
0x4F
0x4B
0x4A
0x49
D4
0x4E
0x4D
0x4C
0x47
D3
D2
0x48
D1
0x43
D0 (LSB)
0x46
0x42
In the serial output mode, a data bit (with unique identifier) needs to be assigned to each location within the
serial output stream. There are a total of 40 addresses available per channel. Channel A spans from address
0x39 to 0x60 and channel B from address 0x61 to 0x88. When using complex decimation, the output bit mapper
is applied to both the “I”and the “Q”sample.
Copyright © 2022 Texas Instruments Incorporated
40
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
2-wire mode: in this mode both the current and the previous sample have to be used in the address space as
shown in 图 8-39. Note: there are unused addresses between samples for resolution less than 20-bit (grey back
ground), which can be skipped if not used.
14-bit
16-bit 18-bit 20-bit
14-bit
16-bit 18-bit 20-bit
DA5
DA6
0x60 0x5F 0x5E 0x5D 0x5C 0x5B 0x5A 0x59 0x58 0x57 0x56 0x55 0x54 0x53 0x52 0x51 0x50 0x4F 0x4E 0x4D
0x4C 0x4B 0x4A 0x49 0x48 0x47 0x46 0x45 0x44 0x43 0x42 0x41 0x40 0x3F 0x3E 0x3D 0x3C 0x3B 0x3A 0x39
0x88 0x87 0x86 0x85 0x84 0x83 0x82 0x81 0x80 0x7F 0x7E 0x7D 0x7C 0x7B 0x7A 0x79 0x78 0x77 0x76 0x75
0x74 0x73 0x72 0x71 0x70 0x6F 0x6E 0x6D 0x6C 0x6B 0x6A 0x69 0x68 0x67 0x66 0x65 0x64 0x63 0x62 0x61
DB5
DB6
Previous Sample
Current Sample
图8-39. 2-wire output bit mapper
In the following example (图8-40), the 16-bit 2-wire serial output is reordered to where lane DA5/DB5 carries the
8 MSB and lane DA6/DB6 carries 8 LSBs.
Previous Sample
Current Sample
D19A
(0x60
0x2D)
D18A
(0x5F
0x2C)
D17A
(0x5E
0x27)
D16A
(0x5D
0x26)
D15A
(0x5C
0x25)
D14A
(0x5B
0x24)
D13A
(0x5A
0x1F)
D12A
(0x59
0x1E)
D19A
(0x56
0x6D)
D18A
(0x55
0x6C)
D17A
(0x54
0x67)
D16A
(0x53
0x66)
D15A
(0x52
0x65)
D14A
(0x51
0x64)
D13A
(0x50
0x5F)
D12A
(0x4F
0x5E)
DA5
DA6
D11A
(0x4C
0x1D)
D10A
(0x4B
0x1C)
D9A
(0x4A
0x17)
D8A
(0x49
0x16)
D7A
(0x48
0x15)
D6A
(0x47
0x14)
D5A
(0x46
0x0F)
D4A
(0x45
0x0E)
D11A
(0x42
0x5D)
D10A
(0x41
0x5C)
D9A
(0x40
0x57)
D8A
(0x39
0x56)
D7A
(0x38
0x55)
D6A
(0x37
0x54)
D5A
(0x36
0x4F)
D4A
(0x35
0x4E)
D19B
(0x88
0x29)
D18B
(0x87
0x28)
D17B
(0x86
0x23)
D16B
(0x85
0x22)
D15B
(0x84
0x21)
D14B
(0x83
0x20)
D13B
(0x82
0x1B)
D12B
(0x81
0x1A)
D19B
(0x7E
0x69)
D18B
(0x7D
0x68)
D17B
(0x7C
0x63)
D16B
(0x7B
0x62)
D15B
(0x7A
0x61)
D14B
(0x79
0x60)
D13B
(0x78
0x5B)
D12B
(0x77
0x5A)
DB5
DB6
D11B
(0x74
0x19)
D10B
(0x73
0x18)
D9B
(0x72
0x13)
D8B
(0x71
0x12)
D7B
(0x70
0x11)
D6B
(0x6F
0x10)
D5B
(0x6E
0x0B)
D4B
(0x6D
0x0A)
D11B
(0x6A
0x59)
D10B
(0x69
0x58)
D9B
(0x68
0x53)
D8B
(0x67
0x52)
D7B
(0x66
0x51)
D6B
(0x65
0x50)
D5B
(0x64
0x4B)
D4B
(0x63
0x4A)
图8-40. Example: 2-wire output mapping
1-wire mode: Only the ‘current’ sample needs to programmed in the address space. If desired, it can be
duplicated on DA5/DB5 as well (using addresses shown in 图 8-41 in order to have a redundant output. Lane
DA5/DB5 needs to be powered up in that case.
14-bit
16-bit
18-bit
20-bit
DA6
(default)
0x4C 0x4B 0x4A 0x49 0x48 0x47 0x46 0x45 0x44 0x43 0x42 0x41 0x40 0x3F 0x3E 0x3D 0x3C 0x3B 0x3A 0x39
0x60 0x5F 0x5E 0x5D 0x5C 0x5B 0x5A 0x59 0x58 0x57 0x56 0x55 0x54 0x53 0x52 0x51 0x50 0x4F 0x4E 0x4D
DA5
DB6
(default)
0x74 0x73 0x72 0x71 0x70 0x6F 0x6E 0x6D 0x6C 0x6B 0x6A 0x69 0x68 0x67 0x66 0x65 0x64 0x63 0x62 0x61
0x88 0x87 0x86 0x85 0x84 0x83 0x82 0x81 0x80 0x7F 0x7E 0x7D 0x7C 0x7B 0x7A 0x79 0x78 0x77 0x76 0x75
DB5
图8-41. 1-wire output bit mapping
½-wire mode: The output is only on lane DA6 and the sample order is programmed into the 40 addresses of
chA (from 0x39 to 0x60). It covers 2 samples (one for chA, one for chB) as shown in 图8-42.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
41
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
18-bit 20-bit
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
14-bit
16-bit
16-bit
18-bit
20-bit
14-bit
...
...
DA6
0x4C 0x4B
0x40 0x3F 0x3E 0x3D 0x3C 0x3B 0x3A 0x39 0x60 0x5F
0x54 0x53 0x52 0x51 0x50 0x4F 0x4E 0x4D
图8-42. 1/2-wire output bit mapping
Copyright © 2022 Texas Instruments Incorporated
42
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.5.5 Output Interface/Mode Configuration
The following sequence summarizes all the relevant registers for changing the output interface and/or enabling
the decimation filter. Steps 1 and 2 must come first since the E-Fuse load reset the SPI writes, the remaining
steps can come in any order.
表8-9. Configuration steps for changing interface or decimation
STEP
FEATURE
ADDRESS
DESCRIPTION
Select the output interface bit mapping depending on resolution and output interface.
Output Resolution
14-bit, 18-bit
2-wire
0x2B
0x4B
1-wire
1/2-wire
0x8D
1
0x07
0x6C
16-bit, 20-bit
Load the output interface bit mapping using the E-fuse loader (0x13, D0). Program register 0x13 to 0x01, wait ~
1ms so that bit mapping is loaded properly followed by 0x13 0x00
2
0x13
3
4
0x0A/B/C
0x18
When changing the output interface bit mapper (0x07), the CMOS output buffer register has to be configured again.
When changing the output interface bit mapper (0x07), the DCLKIN EN bit (D4) has to be set again.
Configure the FCLK frequency based on bypass/decimation and number of lanes used.
FCLK SRC
(D7)
FCLK DIV
(D4)
TOG FCLK
(D0)
Bypass/Dec
SCMOS
2-wire
1-wire
0
0
0
1
1
0
1
0
0
0
0
0
0
0
0
0
0
1
Bypass/ Real
Decimation
5
0x19
1/2-wire
2-wire
Complex Decimation
1-wire
Output
Interface
1/2-wire
6
7
0x1B
0x1F
Select the output interface resolution using the bit mapper (D5-D3).
When changing the output interface bit mapper (0x07), the DCLKIN EN bit (D6) and DCLK OB EN (D4) have to be
set again.
Select the FCLK pattern for decimation for proper duty cycle output of the frame clock.
Output Resolution
14-bit
2-wire
1-wire
1/2-wire
0xFE000
0xFF000
0xFF800
0xFFC00
16-bit
Real Decimation
use default
0x20
0x21
0x22
18-bit
8
20-bit
use default
14-bit
16-bit
Complex Decimation
0xFFFFF
0xFFFFF
18-bit
20-bit
0x39..0x60 Change output bit mapping for chA and chB if desired. This works also with the default interface selection.
0x61..0x88
9
10
11
0x24
0x25
Enable the decimation filter
Configure the decimation filter
0x2A/B/C/D
0x31/2/3/4
12
Program the NCO frequency for complex decimation (can be skipped for real decimation)
Configure the complex output data stream (set both bits to 0 for real decimation)
Decimation
Filter
SCMOS
2-wire
OP-Order (D4)
Q-Delay (D3)
0x27
0x2E
13
14
1
0
1
0
1
1
1-wire
1/2-wire
0x26
Set the mixer gain and toggle the mixer reset bit to update the NCO frequency.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
43
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.3.5.5.1 Configuration Example
The following is a step by step programming example to configure the ADC3660 to complex decimation by 8 with
1-wire SCMOS and 16-bit output.
1. 0x07 (address) 0x6C (load bit mapper configuration for 16-bit output with 1-wire SCMOS)
2. 0x13 0x01, wait 1 ms, 0x13 0x00 (load e-fuse)
3. 0x0A 0xFF, 0x0B 0xEE, 0x0C 0xFD (configure CMOS output buffer)
4. 0x18 0x10 (DCLKIN EN)
5. 0x19 0x82 (configure FCLK)
6. 0x1B 0x08 (select 16-bit output resolution)
7. 0x1F 0x50 (DCLKIN EN and DCLK OB EN)
8. 0x20 0xFF, 0x21 0xFF, 0x22 0x0F (configure FCLK pattern)
9. 0x24 0x06 (enable decimation filter)
10. 0x25 0x30 (configure complex decimation by 8)
11. 0x2A/B/C/D and 0x31/32/33/34 (program NCO frequency)
12. 0x27/0x2E 0x08 (configure Q-delay register bit)
13. 0x26 0xAA, 0x26 0x88 (set digital mixer gain to 6-dB and toggle the mixer update)
8.3.6 Test Pattern
In order to enable in-circuit testing of the digital interface, the following test patterns are supported and enabled
via SPI register writes (0x14/0x15/0x16). The test pattern generator is located after the decimation filter as
shown in 图 8-43. In decimation mode (real and complex), the test patterns replace the output data from the
DDC - however channel A controls the test patterns for both channels.
DIG
I/F
Output
Formatter
14/16/18/
20-bit
NCO
TEST
Output
Bit Mapper
PATTERN
N
图8-43. Test Pattern Generator
• RAMP Pattern: The step size needs to be configured in the CUSTOM PAT register according to the native
resolution of the ADC. When selecting a higher output resolution then the additional LSBs will still be 0 in
RAMP pattern mode.
– 00001: 18-bit output resolution
– 00100: 16-bit output resolution
– 10000: 14-bit output resolution
• Custom Pattern: Configured in the CUSTOM PAT register
Copyright © 2022 Texas Instruments Incorporated
44
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.4 Device Functional Modes
8.4.1 Normal Operation
In normal operating mode, the ADC full-scale input gets converted to a digital output with 16-bit resolution.
8.4.2 Power Down Options
A global power down mode can be enabled via SPI as well as using the power down pin (PDN/SYNC). There is
an internal pull-down 21kΩ resistor on the PDN/SYNC input pin and the pin is active high - so the pin needs to
be pulled high externally to enter global power down mode.
The SPI register map provides the capability to enable/disable individual blocks directly or via PDN pin mask in
order to trade off power consumption vs wake up time as shown in 表8-10.
REFBUF
1.2V REF
Digital Downconverter
NCO
VREF
AIN
Crosspoint
Switch
N
ADC
NCO
Dig I/F
N
BIN
CLK
ADC
图8-44. Power Down Configurations
表8-10. Overview of Power Down Options
PDN
via SPI
Mask for
Global PDN
Feature -
Default
Power
Impact
Wake-up
time
Function/ Register
ADC
Comment
Both ADC channels are included in
Global PDN automatically
Yes
Yes
Yes
-
Enabled
Enabled
Should only be powered down in power
down state.
Reference gain amplifier
Internal 1.2V reference
~ 0.4 mA
~3 us
Internal/external reference selection is
available through SPI and REFBUF pin.
External ref
~ 1-3.5 mA
~3 ms
Yes
Single ended clock input saves ~ 1mA
compared to differential.
Some programmability is available
through the REFBUF pin.
Differential
clock
Clock buffer
Yes
~ 1 mA
varies
n/a
Depending on output interface mode,
unused output drivers can be powered
down for maximum power savings
Output interface drivers
Decimation filter
Yes
Yes
-
-
Enabled
Disabled
n/a
n/a
see electrical
table
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
45
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.4.3 Digital Channel Averaging
The ADC3660 includes a digital channel averaging feature which enables improvement of the ADC dynamic
range (see 图 8-45). The same input signal is given to both ADC inputs externally and the output of the two
ADCs is averaged internally. By averaging, uncorrelated noise (e.g. ADC thermal noise) improves 3-dB while
correlated noise (e.g. jitter in the clock path, reference noise) is unaffected. Therefore the averaging gives close
to 3-dB improvement at low input frequencies but less at high input frequencies where clock jitter dominates the
SNR.
The output from the digital averaging block is given out on the digital outputs of channel A or alternatively can be
routed to the digital decimation filters using the digital mux.
NCO
MUX
N
ADC
AVG
NCO
N
ADC
External
Internal
图8-45. Digital Channel Averaging Diagram
Copyright © 2022 Texas Instruments Incorporated
46
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.5 Programming
The device is primarily configured and controlled using the serial programming interface (SPI) however it can
operate in a default configuration without requiring the SPI interface. Furthermore the power down function as
well as internal/external reference configuration is possible via pin control (PDN/SYNC and REFBUF pin).
备注
The power down command (via PIN or SPI) only goes in effect with the ADC sampling clock present.
After initial power up, the default operating configuration for each device is shown in 表8-11.
表8-11. Default device configuration after power up
FEATURE
Signal Input
Auto-zero
ADC3660
Differential
Disabled
Clock Input
Reference
Decimation
Interface
Differential
External
DDC bypass
2-wire
Output Format
2s complement
8.5.1 Configuration using PINs only
The ADC voltage reference can be selected using the REFBUF pin. Even though there is an internal 100 kΩ
pull-up resistor to AVDD, the REFBUF pin should be set to a voltage externally and not left floating.
表8-12. REFBUF voltage levels control voltage reference selection
REFBUF VOLTAGE
> 1.7 V (Default)
1.2 V (1.15-1.25V)
0.5 - 0.7V
VOLTAGE REFERENCE OPTION
CLOCKING OPTION
Differential clock input
Differential clock input
Differential clock input
Single ended clock input
External reference
External 1.2V input on REFBUF pin using internal gain buffer
Internal reference
< 0.1V
Internal reference
8.5.2 Configuration using the SPI interface
The device has a set of internal registers that can be accessed by the serial interface formed by the SEN (serial
interface enable), SCLK (serial interface clock) and SDIO (serial interface data input/output) pins. Serially shifting
bits into the device is enabled when SEN is low. Serial data input are latched at every SCLK rising edge when
SEN is active (low). The serial data are loaded into the register at every 24th SCLK rising edge when SEN is low.
When the word length exceeds a multiple of 24 bits, the excess bits are ignored. Data can be loaded in multiples
of 24-bit words within a single active SEN pulse. The interface can function with SCLK frequencies from 12 MHz
down to very low speeds (of a few hertz) and also with a non-50% SCLK duty cycle.
8.5.2.1 Register Write
The internal registers can be programmed following these steps:
1. Drive the SEN pin low
2. Set the R/W bit to 0 (bit A15 of the 16-bit address) and bits A[14:12] in address field to 0.
3. Initiate a serial interface cycle by specifying the address of the register (A[11:0]) whose content is written and
4. Write the 8-bit data that are latched in on the SCLK rising edges
图8-46 shows the timing requirements for the serial register write operation.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
47
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
Register Address <11:0>
A7 A6 A5 A4
Register Data <7:0>
R/W
SDIO
0
0
0
0
A11 A10
A9
A8
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
tH,SDIO
tSCLK
tS,SDIO
SCLK
SEN
tS,SEN
tH,SEN
RESET
图8-46. Serial Register Write Timing Diagram
8.5.2.2 Register Read
The device includes a mode where the contents of the internal registers can be read back using the SDIO pin.
This readback mode can be useful as a diagnostic check to verify the serial interface communication between
the external controller and the ADC. The procedure to read the contents of the serial registers is as follows:
1. Drive the SEN pin low
2. Set the R/W bit (A15) to 1. This setting disables any further writes to the registers. Set A[14:12] in address
field to 0.
3. Initiate a serial interface cycle specifying the address of the register (A[11:0]) whose content must be read
4. The device outputs the contents (D[7:0]) of the selected register on the SDIO pin
5. The external controller can latch the contents at the SCLK falling edge
Register Address <11:0>
A7 A6 A5 A4
Register Data <7:0>
D5 D4 D3 D2
R/W
1
tOZD
A0
tOD
SDIO
0
0
0
A11 A10
A9
A8
A3
A2
A1
D7
D6
D1
D0
SCLK
SEN
tODZ
图8-47. Serial Register Read Timing Diagram
Copyright © 2022 Texas Instruments Incorporated
48
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.6 Register Maps
表8-13. Register Map Summary
REGISTER
ADDRESS
REGISTER DATA
A[11:0]
0x00
D7
D6
D5
D4
0
D3
0
D2
D1
0
D0
0
0
0
0
RESET
0x07
OP IF MAPPER
0
OP IF EN
OP IF SEL
PDN
REFAMP
PDN
GLOBAL
0x08
0
0
PDN CLKBUF
0
PDN A
PDN B
0x0A
0x0B
0x0C
CMOS OB DIS [7:0]
CMOS OB DIS [15:8]
CMOS OB DIS [23:16]
MASK
CLKBUF
MASK
REFAMP
MASK BG
DIS
0x0D
0x0E
0
0
0
0
0
SYNC PIN
EN
SPI SYNC SPI SYNC EN
0
REF CTRL
REF SEL
SE CLK EN
0x11
0x13
0x14
0x15
0x16
0x18
0x19
0x1B
0x1E
0x1F
0x20
0x21
0x22
0x24
0x25
0x26
0
0
0
0
SE A
0
SE B
0
0
0
DLL PDN
0
0
0
AZ EN
E-FUSE LD
CUSTOM PAT [7:0]
CUSTOM PAT [15:8]
TEST PAT B
TEST PAT A
CUSTOM PAT [17:16]
0
0
0
0
DCLKIN EN
FCLK DIV
0
0
0
0
0
0
0
0
0
FCLK SRC
MAPPER EN
0
0
20B EN
0
FCLK EN
TOG FCLK
BIT MAPPER RES
0
0
0
0
0
0
CMOS DCLK DEL
0
LOW DR EN DCLKIN EN
0
DCLK OB EN
2X DCLK
FCLK PAT [7:0]
FCLK PAT [15:8]
0
0
0
0
0
FCLK PAT [19:16]
0
CH AVG EN
DECIMATION
MIX RES A
DDC MUX
DIG BYP
0
DDC EN
0
0
DDC MUX EN
REAL OUT
MIX PHASE
FS/4 MIX B
MIX GAIN A
FS/4 MIX A
MIX GAIN B
MIX RES B
FS/4 MIX PH
A
0x27
0
0
0
0
0
OP ORDER A
Q-DEL A
0
0
0x2A
0x2B
0x2C
0x2D
NCO A [7:0]
NCO A [15:8]
NCO A [23:16]
NCO A [31:24]
FS/4 MIX PH
B
0x2E
0
OP ORDER B
Q-DEL B
0
0
0x31
0x32
NCO B [7:0]
NCO B [15:8]
0x33
NCO B [23:16]
0x34
NCO B [31:24]
0x39..0x60
0x61..0x88
0x8F
OUTPUT BIT MAPPER CHA
OUTPUT BIT MAPPER CHB
0
0
0
0
0
0
0
0
0
0
0
0
FORMAT A
FORMAT B
0
0
0x92
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
49
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
8.6.1 Detailed Register Description
图8-48. Register 0x00
7
0
6
0
5
0
4
3
2
0
1
0
0
0
0
RESET
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-14. Register 0x00 Field Descriptions
Bit
Field
0
Type
R/W
R/W
Reset
Description
7-1
0
0
0
Must write 0
RESET
This bit resets all internal registers to the default values and self
clears to 0.
图8-49. Register 0x07
7
6
5
4
3
2
1
0
OP IF MAPPER
R/W-0
0
OP IF EN
R/W-0
OP IF SEL
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-15. Register 0x07 Field Descriptions
Bit
Field
Type
Reset
Description
7-5
OP IF MAPPER
R/W
000
Output interface mapper. This register contains the proper
output interface bit mapping for the different interfaces. The
interface bit mapping is internally loaded from e-fuses and also
requires a fuse load command to go into effect (0x13, D0).
Register 0x07 along with the E-Fuse Load (0x13, D0) needs to
be loaded first in the programming sequence since the E-Fuse
load resets the SPI writes.
After initial reset the default output interface variant is loaded
automatically from fuse internally. However when reading back
this register reads 000 until a value is written using SPI.
001: 2-wire, 18 and 14-bit
010: 2-wire, 20 and 16-bit
011: 1-wire
100: 0.5-wire
others: not used
4
3
0
R/W
R/W
0
0
Must write 0
OP IF EN
Enables changing the default output interface mode (D2-
D0).When changing the output interface mode, the registers
0x0A/0B/0C, 0x18, 0x19 and 0x1F have to written as well.
2-0
OP IF SEL
R/W
000
Selection of the output interface mode. OP IF EN (D3) needs to
be enabled also.
After initial reset the default output interface is loaded
automatically from fuse internally. However when reading back
this register reads 000 until a value is written using SPI.
011: 2-wire
100: 1-wire
101: 0.5-wire
others: not used
Copyright © 2022 Texas Instruments Incorporated
50
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-50. Register 0x08
7
0
6
0
5
4
3
2
1
0
PDN CLKBUF PDN REFAMP
R/W-0 R/W-0
0
PDN A
R/W-0
PDN B
R/W-0
PDN GLOBAL
R/W-0
R/W-0
R/W-0
R/W-0
表8-16. Register 0x08 Field Descriptions
Bit
7-6
5
Field
Type
R/W
R/W
Reset
Description
0
0
0
Must write 0
PDN CLKBUF
Powers down sampling clock buffer
0: Clock buffer enabled
1: Clock buffer powered down
4
PDN REFAMP
R/W
0
Powers down internal reference gain amplifier
0: REFAMP enabled
1: REFAMP powered down
3
2
0
R/W
R/W
0
0
Must write 0
PDN A
Powers down ADC channel A
0: ADC channel A enabled
1: ADC channel A powered down
1
0
PDN B
R/W
R/W
0
0
Powers down ADC channel B
0: ADC channel B enabled
1: ADC channel B powered down
PDN GLOBAL
Global power down via SPI
0: Global power disabled
1: Global power down enabled. Power down mask (register
0x0D) determines which internal blocks are powered down.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
51
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-51. Register 0x0A/B/C
7
6
5
4
3
2
1
0
CMOS OB DIS [23:0]
R/W-0 R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-17. Register 0x0A/B/C Field Descriptions
Bit
Field
CMOS OB DIS [23:0]
Type
Reset
Description
7:0
R/W
0
These register bits power down the individual CMOS output
buffers. See 表8-18 for the actual bit to pin mapping. Unused
pins can be powered down (ie set to 1) for maximum power
savings. Even though unused outputs don't toggle there is still a
small amount of static power (< 1mA) that can be saved by
disabling the output buffers.When changing the output interface
mode (0x07) these registers have to be written again.
There is a separate control to enable the DCLKIN buffer in
register 0x1F (D6) and 0x18 (D4). DCLK output buffer is
powered down using register 0x1F (D4).
0: Output buffer enabled
1: Output buffer powered down
表8-18. Output buffer enable bit mapping vs output interface mode
ADDRESS (HEX)
BIT
PIN NAME
SCMOS 2-w
SCMOS 1-w
SCMOS 1/2-w
D7
DB5
DB5
-
-
D6/D5/D4
D3
-
-
-
-
0x0A
DCLKIN
-
DCLKIN
DCLKIN
DCLKIN
D2/D1/D0
-
0x7F
-
-
0xFF
-
-
0xFF
-
Register setting
D7/D6/D5
D4
-
FCLK
FCLK
-
FCLK
-
FCLK
-
0x0B
0x0C
D3/D2/D1
D0
-
DB6
DB6
0xEE
-
DB6
0xEE
-
-
0xEF
-
Register setting
D7/D6/D5/D4/D3/D2
-
D1
D0
DA6
DA5
DA6
DA5
0xFC
DA6
-
DA6
-
Register setting
0xFD
0xFD
Copyright © 2022 Texas Instruments Incorporated
52
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-52. Register 0x0D (PDN GLOBAL MASK)
7
0
6
0
5
4
3
2
1
0
0
0
0
MASK CLKBUF MASK REFAMP MASK BG DIS
R/W-0 R/W-0 R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-19. Register 0x0D Field Descriptions
Bit
7-4
3
Field
Type
R/W
R/W
Reset
Description
0
0
0
Must write 0
MASK CLKBUF
MASK REFAMP
MASK BG DIS
Global power down mask control for sampling clock input buffer.
0: Clock buffer will get powered down when global power down
is exercised.
1: Clock buffer will NOT get powered down when global power
down is exercised.
2
1
R/W
R/W
0
0
Global power down mask control for reference amplifier.
0: Reference amplifier will get powered down when global power
down is exercised.
1: Reference amplifier will NOT get powered down when global
power down is exercised.
Global power down mask control for internal 1.2V bandgap
voltage reference. Setting this bit reduces power consumption in
global power down mode but increases the wake up time. See
the power down option overview.
0: Internal 1.2V bandgap voltage reference will NOT get
powered down when global power down is exercised.
1: Internal 1.2V bandgap voltage reference will get powered
down when global power down is exercised.
0
0
R/W
0
Must write 0
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
53
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-53. Register 0x0E
7
6
5
4
3
2
1
0
SYNC PIN EN
R/W-0
SPI SYNC
R/W-0
SPI SYNC EN
R/W-0
0
REF CTL
R/W-0
REF SEL
SE CLK EN
R/W-0
R/W-0
R/W-0
R/W-0
表8-20. Register 0x0E Field Descriptions
Bit
Field
SYNC PIN EN
Type
Reset
Description
7
R/W
0
This bit controls the functionality of the SYNC/PDN pin.
0: SYNC/PDN pin exercises global power down mode when pin
is pulled high.
1: SYNC/PDN pin issues the SYNC command when pin is
pulled high.
6
5
SPI SYNC
R/W
R/W
0
0
Toggling this bit issues the SYNC command using the SPI
register write. SYNC using SPI must be enabled as well (D5).
This bit doesn't self reset to 0.
0: Normal operation
1: SYNC command issued.
SPI SYNC EN
This bit enables synchronization using SPI instead of the
SYNC/PDN pin.
0: Synchronization using SPI register bit disabled.
1: Synchronization using SPI register bit enabled.
4
3
0
R/W
R/W
0
0
Must write 0
REF CTL
This bit determines if the REFBUF pin controls the voltage
reference selection or the SPI register (D2-D1).
0: The REFBUF pin selects the voltage reference option.
1: Voltage reference is selected using SPI (D2-D1) and single
ended clock using D0.
2-1
REF SEL
R/W
R/W
00
Selects of the voltage reference option. REF CTRL (D3) must be
set to 1.
00: Internal reference
01: External voltage reference (1.2V) using internal reference
buffer (REFBUF)
10: External voltage reference
11: not used
0
SE CLK EN
0
Selects single ended clock input and powers down the
differential sampling clock input buffer. REF CRTL (D3) must be
set to 1.
0: Differential clock input
1: Single ended clock input
Copyright © 2022 Texas Instruments Incorporated
54
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-54. Register 0x11
7
0
6
0
5
4
3
2
1
0
0
SE A
R/W-0
SE B
R/W-0
0
DLL PDN
R/W-0
AZ EN
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-21. Register 0x11 Field Descriptions
Bit
7-6
5
Field
Type
R/W
R/W
Reset
Description
0
0
0
Must write 0
SE A
This bit enables single ended analog input, channel A
0: Differential input
1: Single ended input
4
SE B
R/W
0
This bit enables single ended analog input, channel B
0: Differential input
1: Single ended input
3
2
0
R/W
R/W
0
0
Must write 0
DLL PDN
This register powers down the internal DLL, which is used to
adjust the sampling time. This register must only be enabled
when operating at sampling rates below 40 MSPS. When DLL
PDN bit is enabled the sampling time is directly dependent on
sampling clock duty cycle (with a 50/50 duty cycle the sampling
time is TS/2).
0: Sampling time is TS/ 4
1: Sampling time is TS/2 (only for sampling rates below 40
MSPS).
1
0
0
R/W
R/W
0
0
Must write 0
AZ EN
This bit enables the internal auto-zero circuitry.
0: Auto-zero disabled
1: Auto-zero enabled
图8-55. Register 0x13
7
0
6
0
5
0
4
3
2
0
1
0
0
0
E-FUSE LD
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-22. Register 0x13 Field Descriptions
Bit
Field
Type
R/W
R/W
Reset
Description
7-1
0
0
0
0
Must write 0
E-FUSE LD
This register bit loads the internal bit mapping for different
interfaces. After setting the interface in register 0x07, this E-
FUSE LOAD bit needs to be set to 1 and reset to 0 for loading to
go into effect. Register 0x07 along with the E-Fuse Load (0x13,
D0) needs to be loaded first in the programming sequence since
the E-Fuse load resets the SPI writes.
0: E-FUSE LOAD set
1: E-FUSE LOAD reset
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
55
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-56. Register 0x14/15/16
7
6
5
4
3
2
1
0
CUSTOM PAT [7:0]
CUSTOM PAT [15:8]
TEST PAT B
R/W-0
TEST PAT A
R/W-0
CUSTOM PAT [17:16]
R/W-0 R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-23. Register 0x14/15/16 Field Descriptions
Bit
Field
CUSTOM PAT [17:0]
Type
Reset
Description
7-0
R/W
00000000 This register is used for two purposes:
•
•
It sets the constant custom pattern starting from MSB
It sets the RAMP pattern increment step size.
00001: Ramp pattern for 18-bit ADC
00100: Ramp pattern for 16-bit ADC
10000: Ramp pattern for 14-bit ADC
7-5
TEST PAT B
R/W
000
Enables test pattern output mode for channel B (NOTE: The test
pattern is set prior to the bit mapper and is based on native
resolution of the ADC starting from the MSB). These work in
either output format.
000: Normal output mode (test pattern output disabled)
010: Ramp pattern: need to set proper increment using
CUSTOM PAT register
011: Constant Pattern using CUSTOM PAT [17:0] in register
0x14/15/16.
others: not used
4-2
TEST PAT A
R/W
000
Enables test pattern output mode for channel A (NOTE: The test
pattern is set prior to the bit mapper and is based on native
resolution of the ADC starting from the MSB). These work in
either output format.
000: Normal output mode (test pattern output disabled)
010: Ramp pattern: need to set proper increment using
CUSTOM PAT register
011: Constant Pattern using CUSTOM PAT [17:0] in register
0x14/15/16.
others: not used
图8-57. Register 0x18
7
0
6
0
5
0
4
3
2
0
1
0
0
0
DCLKIN EN
R/W-0
0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-24. Register 0x18 Field Descriptions
Bit
Field
Type
R/W
R/W
Reset
Description
7-5
4
0
0
1
Must write 0
DCLKIN EN
This bit enables the DCLKIN clock input buffer for serial CMOS
modes. Also DCLKIN EN (0x1F, D6) needs to be set as
well.When changing the otuput interface mode (0x07) this
register has to be written again.
0: DCLKIN buffer powered down.
1: DCLKIN buffer enabled.
3-0
0
R/W
0
Must write 0
Copyright © 2022 Texas Instruments Incorporated
56
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-58. Register 0x19
7
6
0
5
0
4
3
2
0
1
0
FCLK SRC
R/W-0
FCLK DIV
R/W-0
0
FCLK EN
R/W-0
TOG FCLK
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-25. Register 0x19 Field Descriptions
Bit
Field
FCLK SRC
Type
Reset
Description
7
R/W
0
User has to select if FCLK signal comes from ADC or from DDC
block. Here real decimation is treated same as bypass mode
0: FCLK generated from ADC. FCLK SRC set to 0 for DDC
bypass, real decimation mode and 1/2-w complex decimation
mode.
1: FCLK generated from DDC block. In complex decimation
mode only this bit needs to be set for 2-w and 1-w output
interface mode but NOT for 1/2-w mode.
6-5
4
0
R/W
R/W
0
0
Must write 0
FCLK DIV
This bit needs to be set to 1 for 2-w output mode in bypass
mode only (non decimation).
0: All output interface modes except 2-w bypass mode..
1: 2-w output interface mode.
3-2
1
0
R/W
R/W
0
1
Must write 0
FCLK EN
This bit enables FCLK output.
0: FCLK output disabled.
When changing the output interface mode (0x07) this register
has to be written again. 1: FCLK output enabled.
0
TOG FCLK
R/W
0
This bit adjusts the FCLK signal appropriately for 1/2-wire mode
where FCLK is stretched to cover channel A and channel B.
This bit ONLY needs to be set in 1/2-wire mode with complex
decimation mode.
0: all other modes.
1: FCLK for 1/2-wire complex decimation mode.
表8-26. Configuration of FCLK SRC and FCLK DIV Register Bits vs Serial Interface
BYPASS/DECIMATION
SERIAL INTERFACE
FCLK SRC
FCLK DIV
TOG FCLK
2-wire
0
0
0
1
1
0
1
0
0
0
0
0
0
0
0
0
0
1
Decimation Bypass/ Real Decimation
Complex Decimation
1-wire
1/2-wire
2-wire
1-wire
1/2-wire
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
57
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-59. Register 0x1B
7
6
5
4
3
2
0
1
0
0
0
MAPPER EN
R/W-0
20B EN
R/W-0
BIT MAPPER RES
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-27. Register 0x1B Field Descriptions
Bit
Field
MAPPER EN
Type
Reset
Description
7
R/W
0
This bit enables changing the resolution of the output (including
output serialization factor) in bypass mode only. This bit is not
needed for 20-bit resolution.
0: Output bit mapper disabled.
1: Output bit mapper enabled.
6
20B EN
R/W
R/W
0
This bit enables 20-bit output resolution which can be useful for
very high decimation settings so that quantization noise doesn't
impact the ADC performance.
0: 20-bit output resolution disabled.
1: 20-bit output resolution enabled.
5-3
BIT MAPPER RES
000
Sets the output resolution using the bit mapper. MAPPER EN bit
(D6) needs to be enabled when operating in bypass mode..
000: 18 bit
001: 16 bit
010: 14 bit
all others, n/a
2-0
0
R/W
0
Must write 0
表8-28. Register Settings for Output Bit Mapper vs Operating Mode
BYPASS/DECIMATION
Decimation Bypass
Real Decimation
OUTPUT RESOLUTION
MAPPER EN (D7)
BIT MAPPER RES (D5-D3)
Resolution Change
1
0
0
000: 18-bit
001: 16-bit
010: 14-bit
Resolution Change (default 18-bit)
Complex Decimation
图8-60. Register 0x1E
7
0
6
0
5
4
3
2
0
1
0
0
0
CMOS DCLK DEL
R/W-0 R/W-0
0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-29. Register 0x1E Field Descriptions
Bit
Field
Type
R/W
R/W
Reset
Description
7-6
5-4
0
0
Must write 0
CMOS DCLK DEL
00
These bits adjust the output timing of CMOS DCLK output.
00: no delay
01: DCLK advanced by 50 ps
10: DCLK delayed by 50 ps
11: DCLK delayed by 100 ps
3-0
0
R/W
0
Must write 0
Copyright © 2022 Texas Instruments Incorporated
58
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-61. Register 0x1F
7
6
5
0
4
3
2
0
1
0
0
0
LOW DR EN
R/W-0
DCLKIN EN
R/W-0
DCLK OB EN
R/W-0
2X DCLK
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-30. Register 0x1F Field Descriptions
Bit
Field
LOW DR EN
Type
Reset
Description
7
R/W
0
This bit impacts the output drive strength of the CMOS output
buffers. This bit can be enabled at slow speeds in order to save
power consumption but it will degrade the rise and fall times.
0: Low drive strength disabled.
1: Low drive strength enabled.
6
DCLKIN EN
R/W
1
This bit enables the DCLKIN clock input buffer for serial CMOS
modes. DCLKIN EN (0x18, D4) needs to be set as well.
When changing the output interface mode this register has to be
written again.
0: DCLKIN buffer powered down.
1: DCLKIN buffer enabled.
5
4
0
R/W
R/W
0
1
Must write 0
DCLK OB EN
This bit enables DCLK output buffer. When changing the output
interface mode (0x07) this register has to be written again.
0: DCLK output buffer powered down.
1: DCLK output buffer enabled.
3
2X DCLK
R/W
0
0
This bit enables SDR output clocking with serial CMOS mode.
When this mode is enabled, DCLKIN required is twice as fast
and data is output only on rising edge of DCLK.
0: Data output on DCLK rising and falling edge.
1: 2x DCLK mode enabled.
2-0
0
R/W
Must write 0
图8-62. Register 0x20/21/22
7
0
6
5
4
3
2
1
0
FCLK PAT [7:0]
FCLK PAT [15:8]
0
0
0
FCLK PAT [19:16]
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-31. Register 0x20/21/22 Field Descriptions
Bit
7-0
Field
Type
Reset
Description
FCLK PAT [19:0]
R/W
0xFFC00
These bits can adjust the duty cycle of the FCLK. In decimation
bypass mode the FCLK pattern gets adjusted automatically for
the different output resolutions. 表8-32 shows the proper FCLK
pattern values for 1-wire and 1/2-wire in real/complex
decimation.
表8-32. FCLK Pattern for different resolution based on interface
DECIMATION
OUTPUT RESOLUTION
2-WIRE
1-WIRE
0xFE000
0xFF000
0xFF800
0xFFC00
0xFFFFF
0xFFFFF
0xFFFFF
0xFFFFF
1/2-WIRE
14-bit
16-bit
18-bit
20-bit
14-bit
16-bit
18-bit
20-bit
REAL DECIMATION
Use Default
Use Default
0xFFFFF
0xFFFFF
0xFFFFF
0xFFFFF
COMPLEX
DECIMATION
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
59
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-63. Register 0x24
7
0
6
0
5
4
3
2
1
0
0
CH AVG EN
R/W-0
DDC MUX
DIG BYP
R/W-0
DDC EN
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-33. Register 0x24 Field Descriptions
Bit
Field
Type
R/W
R/W
Reset
Description
7-6
5
0
0
0
Must write 0
CH AVG EN
Averages the output of ADC channel A and channel B together.
The DDC MUX has to be enabled and set to '11'. The
decimation filter needs to be enabled and set to bypass (fullrate
output) or decimation and DIG BYP set to 1.
0: Channel averaging feature disabled
1: Output of channel A and channel B are averaged: (A+B)/2.
4-3
DDC MUX
R/W
R/W
0
0
Configures DDC MUX in front of the decimation filter.
00: ADC channel A connected to DDC A; ADC Channel B
connected to DDC B
01: ADC channel A connected to DDC A and DDC B.
10: ADC channel B connected to DDC A and DDC B.
11: Output of ADC averaging block (see CH AVG EN) given to
DDC A and DDC B.
2
DIG BYP
This bit needs to be set to enable digital features block which
includes decimation.
0: Digital feature block bypassed - lowest latency
1: Data path includes digital features
1
0
DDC EN
0
R/W
R/W
0
0
Enables internal decimation filter for both channels
0: DDC disabled.
1: DDC enabled.
Must write 0
To output
interface
DDC
N
N
CH
Average
DECIMATION
DIG BYP
DDC
DDC MUX
To output
interface
图8-64. Register control for digital features
Copyright © 2022 Texas Instruments Incorporated
60
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-65. Register 0x25
7
6
5
4
3
2
0
1
0
0
DDC MUX EN
R/W-0
DECIMATION
R/W-0
REAL OUT
R/W-0
MIX PHASE
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-34. Register 0x25 Field Descriptions
Bit
Field
DDC MUX EN
Type
Reset
Description
7
R/W
0
Enables the digital mux between ADCs and decimation filters.
This bit is required for DDC mux settings in register 0x24 (D4,
D3) to go into effect.
0: DDC mux disabled
1: DDC mux enabled
6-4
DECIMATION
R/W
000
Complex decimation setting. This applies to both channels.
000: Bypass mode (no decimation)
001: Decimation by 2
010: Decimation by 4
011: Decimation by 8
100: Decimation by 16
101: Decimation by 32
others: not used
3
REAL OUT
R/W
0
This bit selects real output decimation. This mode applies to
both channels. In this mode, the decimation filter is a low pass
filter and no complex mixing is performed to reduce power
consumption. For maximum power savings the NCO in this case
should be set to 0.
0: Complex decimation
1: Real decimation
2-1
0
0
R/W
R/W
0
0
Must write 0
MIX PHASE
This bit used to invert the NCO phase
0: NCO phase as is.
1: NCO phase inverted.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
61
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-66. Register 0x26
7
6
5
4
3
2
1
0
MIX GAIN A
MIX RES A
R/W-0
FS/4 MIX A
R/W-0
MIX GAIN B
MIX RES B
R/W-0
FS/4 MIX B
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-35. Register 0x26 Field Descriptions
Bit
Field
Type
Reset
Description
7-6
MIX GAIN A
R/W
00
This bit applies a 0, 3 or 6-dB digital gain to the output of digital
mixer to compensate for the mixing loss for channel A.
00: no digital gain added
01: 3-dB digital gain added
10: 6-dB digital gain added
11: not used
5
4
MIX RES A
FS/4 MIX A
R/W
R/W
0
0
Toggling this bit resets the NCO phase of channel A and loads
the new NCO frequency. This bit does not self reset.
Enables complex mixing with FS/4 for DDC A.
0: FS/4 mixing disabled.
1: FS/4 mixing enabled.
3-2
MIX GAIN B
R/W
00
This bit applies a 0, 3 or 6-dB digital gain to the output of digital
mixer to compensate for the mixing loss for channel B.
00: no digital gain added
01: 3-dB digital gain added
10: 6-dB digital gain added
11: not used
1
0
MIX RES B
FS/4 MIX B
R/W
R/W
0
0
Toggling this bit resets the NCO phase of channel B and loads
the new NCO frequency. This bit does not self reset.
Enables complex mixing with FS/4 for DDC B.
0: FS/4 mixing disabled.
1: FS/4 mixing enabled.
图8-67. Register 0x27
7
0
6
0
5
0
4
3
2
1
0
0
0
OP ORDER A
R/W-0
Q-DEL A
R/W-0
FS/4 MIX PH A
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-36. Register 0x27 Field Descriptions
Bit
Field
Type
R/W
R/W
Reset
Description
7-5
4
0
0
0
Must write 0
OP ORDER A
Swaps the I and Q output order for channel A. See 表8-37 for
recommended settings. Only used with complex decimation. Set
to 0 with real decimation.
0: Output order is I[n], Q[n]
1: Output order is swapped: Q[n], I[n]
3
Q-DEL A
R/W
0
This delays the Q-sample output of channel A by one. See 表
8-37 for recommended settings. Only used with complex
decimation. Set to 0 with real decimation.
0: Output order is I[n], Q[n]
1: Q-sample is delayed by 1 sample: I[n], Q[n+1], I[n+1], Q[n+2]
2
FS/4 MIX PH A
0
R/W
R/W
0
0
Inverts the mixer phase for channel A when using FS/4 mixer
0: Mixer phase is non-inverted
1: Mixer phase is inverted
1-0
Must write 0
Copyright © 2022 Texas Instruments Incorporated
62
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
表8-37. OP-ORDER and Q-DELAY Register Settings for Complex Decimation
SCMOS INTERFACE
OP-ORDER
Q-DELAY
2-wire
1-wire
1
0
1
0
1
1
1/2-wire
图8-68. Register 0x2A/B/C/D
7
6
5
4
3
2
1
0
NCO A [7:0]
NCO A [15:8]
NCO A [23:16]
NCO A [31:24]
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-38. Register 0x2A/2B/2C/2D Field Descriptions
Bit
7-0
Field
NCO A [31:0]
Type
Reset
Description
R/W
0
Sets the 32 bit NCO value for decimation filter channel A. The
NCO value is fNCO× 232/FS
In real decimation mode these registers are automatically set to
0.
图8-69. Register 0x2E
7
0
6
5
0
4
3
2
1
0
0
0
0
OP ORDER B
R/W-0
Q-DEL B
R/W-0
FS/4 MIX PH B
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-39. Register 0x2E Field Descriptions
Bit
Field
Type
R/W
R/W
Reset
Description
7-5
4
0
0
0
Must write 0
OP ORDER B
Swaps the I and Q output order for channel B. See 表8-37 for
recommended settings. Only used with complex decimation. Set
to 0 with real decimation.
0: Output order is I[n], Q[n]
1: Output order is swapped: Q[n], I[n]
3
Q-DEL B
R/W
0
This delays the Q-sample output of channel B by one. See 表
8-37 for recommended settings. Only used with complex
decimation. Set to 0 with real decimation.
0: Output order is I[n], Q[n]
1: Q-sample is delayed by 1 sample: I[n], Q[n+1], I[n+1], Q[n+2]
2
FS/4 MIX PH B
0
R/W
R/W
0
0
Inverts the mixer phase for channel B when using FS/4 mixer
0: Mixer phase is non-inverted
1: Mixer phase is inverted
1-0
Must write 0
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
63
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-70. Register 0x31/32/33/34
7
6
5
4
3
2
1
0
NCO B [7:0]
NCO B [15:8]
NCO B [23:16]
NCO B [31:24]
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-40. Register 0x31/32/33/34 Field Descriptions
Bit
7-0
Field
NCO B [31:0]
Type
Reset
Description
R/W
0
Sets the 32 bit NCO value for decimation filter channel B. The
NCO value is fNCO× 232/FS
In real decimation mode these registers are automatically set to
0.
图8-71. Register 0x39..0x60
7
6
5
4
3
2
1
0
OUTPUT BIT MAPPER CHA
R/W-0 R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-41. Register 0x39..0x60 Field Descriptions
Bit
7-0
Field
Type
Reset
Description
OUTPUT BIT MAPPER CHA
R/W
0
These registers are used to reorder the output data bus. See the
节8.3.5.4 on how to program it.
图8-72. Register 0x61..0x88
7
6
5
4
3
2
1
0
OUTPUT BIT MAPPER CHB
R/W-0 R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-42. Register 0x61..0x88 Field Descriptions
Bit
7-0
Field
Type
Reset
Description
OUTPUT BIT MAPPER CHB
R/W
0
These registers are used to reorder the output data bus. See the
节8.3.5.4 on how to program it.
Copyright © 2022 Texas Instruments Incorporated
64
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
图8-73. Register 0x8F
7
0
6
0
5
0
4
3
2
0
1
0
0
0
0
FORMAT A
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-43. Register 0x8F Field Descriptions
Bit
7-2
1
Field
Type
R/W
R/W
Reset
Description
0
0
0
Must write 0
FORMAT A
This bit sets the output data format for channel A. Digital bypass
register bit (0x24, D2) needs to be enabled as well.
0: 2s complement
1: Offset binary
0
0
R/W
0
Must write 0
图8-74. Register 0x92
7
0
6
0
5
0
4
3
2
0
1
0
0
0
0
FORMAT B
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
表8-44. Register 0x92 Field Descriptions
Bit
Field
Type
R/W
R/W
Reset
Description
7-2
1
0
0
0
Must write 0
FORMAT B
This bit sets the output data format for channel B. Digital bypass
register bit (0x24, D2) needs to be enabled as well.
0: 2s complement
1: Offset binary
0
0
R/W
0
Must write 0
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
65
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
9 Application and Implementation
备注
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
9.1 Typical Application
A sonar receiver is a typical frequency domain application for the ADC3660 and its front end circuitry is very
similar to several other systems such as software defined radio (SDR), spectrum analyzer, radar or
communications. Some applications require frequency coverage including DC or near DC (such as, sonar), so it
is included in this example.
图9-1. Typical configuration for a spectrum analyzer with DC support
9.1.1 Design Requirements
Frequency domain applications cover a wide range of frequencies from low input frequencies at or near DC in
the 1st Nyquist zone to undersampling in higher Nyquist zones. If very low input frequency is supported then the
input has to be DC coupled and the ADC driven by a fully differential amplifier (FDA). If low frequency support is
not needed then AC coupling and use of a balun may be more suitable.
The internal reference is used since DC precision is not needed. However the ADC AC performance is highly
dependent on the quality of the external clock source. If in-band interferers can be present then the ADC SFDR
performance will be a key care about as well. A higher ADC sampling rate is desirable in order to relax the
external anti-aliasing filter –an internal decimation filter can be used to reduce the digital output rate afterwards.
表9-1. Design key care-abouts
FEATURE
DESCRIPTION
Signal Bandwidth
Input Driver
DC to 2 MHz
Single ended to differential signal conversion and DC coupling
Copyright © 2022 Texas Instruments Incorporated
66
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
表9-1. Design key care-abouts (continued)
FEATURE
DESCRIPTION
Clock Source
External clock with low jitter
When designing the amplifier/filter driving circuit, the ADC input full-scale voltage needs to be taken into
consideration. For example, the ADC3660 input full-scale is 3.2Vpp. When factoring in ~ 1 dB for insertion loss
of the filter, then the amplifier needs to deliver close to 3.6Vpp. The amplifier distortion performance will degrade
with a larger output swing and considering the ADC common mode input voltage the amplifier may not be able to
deliver the full swing. The ADC3660 provides an output common mode voltage of 0.95V and the THS4551 for
example can only swing all the way to its negative supply. A unipolar 3.3 V amplifier power supply will thus limit
the maximum voltage swing to ~ 3.8Vpp. If a larger output swing is required (ie larger filter insertion loss) then a
negative supply for the amplifier is needed in order to eliminate that limitation. Additionally input voltage
protection diodes may be needed to protect the ADC from over-voltage events.
表9-2. Output voltage swing of THS4541 vs power supply
DEVICE
MIN OUTPUT VOLTAGE
MAX SWING WITH 3.3 V/ 0 V SUPPLY
THS4551
VS-
3.8 Vpp
9.1.2 Detailed Design Procedure
9.1.2.1 Input Signal Path
Depending on desired input signal frequency range the THS4551 and THS4541 provide very good low power
options to drive the ADC inputs. 表 9-3 provides a comparison between the THS4551 and THS4541 and the
power consumption vs usable frequency trade off.
表9-3. Fully Differential Amplifier Options
DEVICE
THS4561
THS4551
THS4541
CURRENT (IQ) PER CHANNEL
USABLE FREQUENCY RANGE
0.8 mA
1.4 mA
10 mA
< 3 MHz
< 10 MHz
< 70 MHz
The low pass filter design (topology, filter order) is driven by the application itself. However, when designing the
low pass filter, the optimum load impedance for the amplifier should be taken into consideration as well. Between
the low pass filter and the ADC input the sampling glitch filter needs to added as well as shown in 节8.3.1.2.1. In
this example the DC - 30 MHz glitch filter is selected.
9.1.2.2 Sampling Clock
Applications operating with low input frequencies (such as DC to 2 MHz) typically are less sensitive to
performance degradation due to clock jitter. The internal ADC aperture jitter improves with faster rise and fall
times (i.e. square wave vs sine wave). 表 9-4 provides an overview of the estimated SNR performance of the
ADC3660 based on different amounts of jitter of the external clock source. The SNR is estimated based on
ADC3660 thermal noise of 82 dBFS and input signal at -1dBFS in decimation bypass mode.
表9-4. ADC SNR performance across vs input frequency for different amounts of external clock jitter
INPUT FREQUENCY
TJ,EXT = 100 fs
TJ,EXT = 250 fs
TJ,EXT = 500 fs
TJ,EXT = 1 ps
1 MHz
82.0
82.0
82.0
82.0
82.0
81.9
82.0
82.0
81.8
82.0
2 MHz
81.9
5 MHz
81.5
Termination of the clock input should be considered for long clock traces.
9.1.2.3 Voltage Reference
The ADC3660 is configured to internal reference operation by applying 0.6 V to the REFBUF pin.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
67
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
9.1.3 Application Curves
The following FFT plots show the performance of THS4541 driving the ADC3660 operated at 65 MSPS with a
full-scale input at -1 dBFS. The first FFT spectrum below shows the performance with a single tone input at FIN
1 MHz and decimation by 16 (real).
=
The second FFT spectrum shows the a single tone input at FIN = 5 MHz and complex decimation by 16 where
the NCO is programmed to 4.5 MHz.
0
-20
0
-20
-40
-40
-60
-60
-80
-80
-100
-120
-140
-100
-120
-140
0
0.5
1
Input Frequency (MHz)
1.5
2
-2.5
-2
-1.5
-1
-0.5
0
0.5
Input Frequency (MHz)
1
1.5
2
2.5
ADC3
ADC3
Decimation by 16, real
Decimation by 16, complex, NCO = 4.5 MHz
图9-2. Single Tone FFT at FIN = 1 MHz
图9-3. Single Tone FFT at FIN = 5 MHz
Copyright © 2022 Texas Instruments Incorporated
68
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
9.2 Initialization Set Up
After power-up, the internal registers must be initialized to their default values through a hardware reset by
applying a high pulse on the RESET pin, as shown in 图9-4.
1. Apply AVDD and IOVDD (no specific sequence required). After AVDD is applied the internal bandgap
reference will power up and settle out in ~ 2ms.
2. Configure REFBUF pin (pull high or low even if configured via SPI later on) and apply the sampling clock.
3. Apply hardware reset. After hardware reset is released, the default registers are loaded from internal fuses
and the internal power up capacitor calibration is initiated. The calibration takes approximately 200000 clock
cycles.
4. Begin programming using SPI interface.
t2
AVDD
IOVDD
t1
REFBUF
Ext VREF
CLK
t4
t3
RESET
SEN
图9-4. Initialization of Serial Registers after Power up
表9-5. Power-up Timing
MIN
TYP
MAX
UNIT
t1
t2
t3
t4
Power-on delay: delay from power up to logic level of REFBUF pin
Delay from REFBUF pin logic level to RESET rising edge
RESET pulse width
2
100
ms
ns
us
1
Delay from RESET disable to SEN active
~ 200000
clock cycles
9.2.1 Register Initialization During Operation
If required, the serial interface registers can be cleared and reset to default settings during operation either:
• through a hardware reset or
• by applying a software reset. When using the serial interface, set the RESET bit (D0 in register address 0x00)
high. This setting initializes the internal registers to the default values and then self-resets the RESET bit low.
In this case, the RESET pin is kept low.
After hardware or software reset the wait time is also ~ 200000 clock cycles before the SPI registers can be
programmed.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
69
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
10 Power Supply Recommendations
The ADC3660 requires two different power-supplies. The AVDD rail provides power for the internal analog
circuits and the ADC itself while the IOVDD rail powers the digital interface and the internal digital circuits like
decimation filter or output interface mapper. Power sequencing is not required.
The AVDD power supply must be low noise in order to achieve data sheet performance. In applications
operating near DC, the 1/f noise contribution of the power supply needs to be considered as well. The ADC is
designed for very good PSRR which aides with the power supply filter design.
55
50
45
40
35
30
0.05 0.1
1
10
Frequency of Signal on AVDD (MHz)
100
D42_
图10-1. Power supply rejection ratio (PSRR) vs frequency
There are two recommended power-supply architectures:
1. Step down using high-efficiency switching converters, followed by a second stage of regulation using a low
noise LDO to provide switching noise reduction and improved voltage accuracy.
2. Directly step down the final ADC supply voltage using high-efficiency switching converters. This approach
provides the best efficiency, but care must be taken to ensure switching noise is minimized to prevent
degraded ADC performance.
TI WEBENCH Power Designer can be used to select and design the individual power-supply elements needed:
see the WEBENCH Power Designer
Recommended switching regulators for the first stage include the TPS62821, and similar devices.
Recommended low dropout (LDO) linear regulators include the TPS7A4701, TPS7A90, LP5901, and similar
devices.
For the switch regulator only approach, the ripple filter must be designed with a notch frequency that aligns with
the switching ripple frequency of the DC/DC converter. Note the switching frequency reported from WEBENCH
and design the EMI filter and capacitor combination to have the notch frequency centered as needed. 图 10-2
and 图10-3 illustrate the two approaches.
AVDD and IOVDD supply voltages should not be shared in order to prevent digital switching noise from coupling
into the analog signal chain.
Copyright © 2022 Texas Instruments Incorporated
70
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
FB
FB
2.1V
1.8V
DC/DC
Regulator
5V-12V
LDO
AVDD
10uF 10uF 0.1uF
47uF
47uF
GND
GND
GND
FB
IOVDD
10uF 10uF 0.1uF
FB = Ferrite bead filter
GND
图10-2. Example: LDO Linear Regulator Approach
EMI FILTER
FB
1.8V
DC/DC
Regulator
5V-12V
AVDD
10uF 10uF 10uF
10uF 10uF 0.1uF
GND
GND
FB
IOVDD
10uF 10uF 0.1uF
GND
Ripple filter notch frequency to match switching frequency of the DC/DC regulator
FB = Ferrite bead filter
图10-3. Example Switcher-Only Approach
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
71
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
11 Layout
11.1 Layout Guidelines
There are several critical signals which require specific care during board design:
1. Analog input and clock signals
• Traces should be as short as possible and vias should be avoided where possible to minimize impedance
discontinuities.
• Traces should be routed using loosely coupled 100-Ωdifferential traces.
• Differential trace lengths should be matched as close as possible to minimize phase imbalance and HD2
degradation.
2. Digital output interface
• A 20 ohm series isolation resistor should be used on each CMOS output and placed close the digital
output. This isolation resistor limits the output current into the capacitive load and thus minimizes the
switching noise inside the ADC. When driving longer distances a buffer should be used. The resistor
value should be optimized for the desired output data rate.
3. Voltage reference
• The bypass capacitor should be placed as close to the device pins as possible and connected between
VREF and REFGND –on top layer avoiding vias.
• Depending on configuration an additional bypass capacitor between REFBUF and REFGND may be
recommended and should also be placed as close to pins as possible on top layer.
4. Power and ground connections
• Provide low resistance connection paths to all power and ground pins.
• Use power and ground planes instead of traces.
• Avoid narrow, isolated paths which increase the connection resistance.
• Use a signal/ground/power circuit board stackup to maximize coupling between the ground and power
plane.
11.2 Layout Example
The following screen shot shows the top layer of the ADC364x/ADC3660 EVM.
• Signal and clock inputs are routed as differential signals on the top layer avoiding vias.
• Serial CMOS output interface lanes with isolation resistor and digital buffer.
• Bypass caps are close to the VREF pin on the top layer avoiding vias.
CMOS output lines with
isolation resistor and buffer
close by
Bypass caps on VREF close
to the pins
Clock routing
without vias
Analog inputs on
top layer (no vias)
图11-1. Layout example: top layer of ADC3660 EVM
Copyright © 2022 Texas Instruments Incorporated
72
Submit Document Feedback
Product Folder Links: ADC3660
ADC3660
www.ti.com.cn
ZHCSM31B –SEPTEMBER 2020 –REVISED MARCH 2022
12 Device and Documentation Support
12.1 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料，可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范，并且不一定反映 TI 的观点；请参阅
TI 的《使用条款》。
12.2 Trademarks
TI E2E™ is a trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
12.3 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
12.4 术语表
TI 术语表
本术语表列出并解释了术语、首字母缩略词和定义。
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
73
Product Folder Links: ADC3660
PACKAGE OPTION ADDENDUM
www.ti.com
28-Feb-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
ADC3660IRSBR
ADC3660IRSBT
ACTIVE
ACTIVE
WQFN
WQFN
RSB
RSB
40
40
3000 RoHS & Green
250 RoHS & Green
NIPDAU
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 105
-40 to 105
AZ3660
AZ3660
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
28-Feb-2022
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
28-Feb-2022
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
ADC3660IRSBR
WQFN
RSB
40
3000
330.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
28-Feb-2022
*All dimensions are nominal
Device
Package Type Package Drawing Pins
WQFN RSB 40
SPQ
Length (mm) Width (mm) Height (mm)
350.0 350.0 43.0
ADC3660IRSBR
3000
Pack Materials-Page 2
PACKAGE OUTLINE
RSB0040E
WQFN - 0.8 mm max height
S
C
A
L
E
2
.
7
0
0
PLASTIC QUAD FLATPACK - NO LEAD
5.1
4.9
B
A
PIN 1 INDEX AREA
5.1
4.9
C
0.8 MAX
SEATING PLANE
0.08 C
0.05
0.00
2X 3.6
(0.2) TYP
EXPOSED
11
20
THERMAL PAD
36X 0.4
10
21
2X
41
SYMM
3.6
3.15 0.1
1
30
0.25
0.15
40X
40
31
PIN 1 ID
(OPTIONAL)
0.1
C A B
SYMM
0.5
0.3
0.05
40X
4219096/A 11/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
RSB0040E
WQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(
3.15)
SYMM
40
31
40X (0.6)
40X (0.2)
1
30
36X (0.4)
41
SYMM
(4.8)
(1.325)
(
0.2) TYP
VIA
10
21
(R0.05)
TYP
11
20
(1.325)
(4.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
0.05 MIN
ALL AROUND
0.05 MAX
ALL AROUND
SOLDER MASK
OPENING
METAL
EXPOSED
METAL
EXPOSED
METAL
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4219096/A 11/2017
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
RSB0040E
WQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(0.785)
4X ( 1.37)
40
31
40X (0.6)
1
30
40X (0.2)
36X (0.4)
SYMM
(0.785)
(4.8)
41
(R0.05) TYP
10
21
METAL
TYP
20
11
SYMM
(4.8)
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
EXPOSED PAD 41
75% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
SCALE:20X
4219096/A 11/2017
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据（包括数据表）、设计资源（包括参考设计）、应用或其他设计建议、网络工具、安全信息和其他资源，
不保证没有瑕疵且不做出任何明示或暗示的担保，包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任：(1) 针对您的应用选择合适的 TI 产品，(2) 设计、验
证并测试您的应用，(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更，恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务，TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址：Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022，德州仪器 (TI) 公司
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明