ADS1605IPAPT [TI]
16-Bit, 5MSPS Analog-to-Digital Converter; 16位5MSPS模拟数字转换器型号: | ADS1605IPAPT |
厂家: | TEXAS INSTRUMENTS |
描述: | 16-Bit, 5MSPS Analog-to-Digital Converter |
文件: | 总38页 (文件大小:1096K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ADS1605
ADS1606
SBAS274H − MARCH 2003 − REVISED MAY 2007
16-Bit, 5MSPS
Analog-to-Digital Converter
FD EATURES
DESCRIPTION
The ADS1605 and ADS1606 are high-speed, high-pre-
cision, delta-sigma analog-to-digital converters (ADCs)
with 16-bit resolution. The data rate is 5 mega-samples
per second (MSPS), the bandwidth (−3dB) is 2.45MHz,
and passband ripple is less than 0.0025dB (to
2.2MHz). Both devices offer the same outstanding per-
formance at these speeds with a signal-to-noise ratio up
to 88dB, total harmonic distortion down to −99dB, and
a spurious-free dynamic range up to 101dB. For even
higher-speed operation, the data rate can be doubled to
10MSPS in 2X mode. The ADS1606 includes an adjust-
able first-in first-out buffer (FIFO) for the output data.
Data Rate: 5MSPS (10MSPS in 2X Mode)
Signal-to-Noise Ratio: 88dB
D
D
D
D
D
D
D
D
Total Harmonic Distortion: −99dB
Spurious-Free Dynamic Range: 101dB
Linear Phase with 2.45MHz Bandwidth
Passband Ripple: 0.0025dB
Selectable On-Chip Reference
Directly Connects to TMS320C6000 DSPs
Easily Upgradable to 18 Bits with the
ADS1625 and ADS1626
The input signal is measured against a voltage refer-
ence that can be generated on-chip or supplied exter-
nally. The digital output data are provided over a simple
parallel interface that easily connects to digital signal
processors (DSPs). An out-of-range monitor reports
when the input range has been exceeded. The
ADS1605/6 operate from a +5V analog supply (AVDD)
and +3V digital supply (DVDD). The digital I/O supply
(IOVDD) operates from +2.7 to +5.25V, enabling the
digital interface to support a range of logic families. The
analog power dissipation is set by an external resistor
and can be reduced when operating at slower speeds.
A power down mode, activated by a digital I/O pin, shuts
down all circuitry. The ADS1605/6 are offered in a
TQFP-64 package using TI PowerPAD technology.
D
D
D
Adjustable Power Dissipation: 315 to 570mW
Power Down Mode
Supplies: Analog
Digital
+5V
+3V
Digital I/O +2.7V to +5.25V
AD PPLICATIONS
Scientific Instruments
D
D
D
D
Automated Test Equipment
Data Acquisition
Medical Imaging
Vibration Analysis
The ADS1605 and ADS1606, along with their 18-bit
counterparts, the ADS1625 and ADS1626, are well
suited for the demanding measurement requirements
of scientific instrumentation, automated test equip-
ment, data acquisition, and medical imaging.
VREFP VREFN VMID RBIAS VCAP
AVDD DVDD IOVDD
PD
Reference and Bias Circuits
REFEN
RESET
CLK
CS
I/O
2XMODE
AINP
AINN
DS
Digital
Filter
Interface
RD
Modulator
DRDY
OTR
ADS1606 Only
FIFO
DOUT[15:0]
ADS1605
ADS1606
FIFO_LEV[2:0]
AGND
DGND
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments. All other trademarks are the property of their respective owners.
ꢀꢁ ꢂ ꢃꢄ ꢅ ꢆꢇ ꢂꢈ ꢃ ꢉꢆꢉ ꢊꢋ ꢌꢍ ꢎ ꢏꢐ ꢑꢊꢍꢋ ꢊꢒ ꢓꢔ ꢎ ꢎ ꢕꢋꢑ ꢐꢒ ꢍꢌ ꢖꢔꢗ ꢘꢊꢓ ꢐꢑꢊ ꢍꢋ ꢙꢐ ꢑꢕꢚ ꢀꢎ ꢍꢙꢔ ꢓꢑꢒ
ꢓ ꢍꢋ ꢌꢍꢎ ꢏ ꢑꢍ ꢒ ꢖꢕ ꢓ ꢊ ꢌꢊ ꢓ ꢐ ꢑꢊ ꢍꢋꢒ ꢖ ꢕꢎ ꢑꢛꢕ ꢑꢕ ꢎ ꢏꢒ ꢍꢌ ꢆꢕꢜ ꢐꢒ ꢇꢋꢒ ꢑꢎ ꢔꢏ ꢕꢋꢑ ꢒ ꢒꢑ ꢐꢋꢙ ꢐꢎ ꢙ ꢝ ꢐꢎ ꢎ ꢐ ꢋꢑꢞꢚ
ꢀꢎ ꢍ ꢙꢔꢓ ꢑ ꢊꢍ ꢋ ꢖꢎ ꢍ ꢓ ꢕ ꢒ ꢒ ꢊꢋ ꢟ ꢙꢍ ꢕ ꢒ ꢋꢍꢑ ꢋꢕ ꢓꢕ ꢒꢒ ꢐꢎ ꢊꢘ ꢞ ꢊꢋꢓ ꢘꢔꢙ ꢕ ꢑꢕ ꢒꢑꢊ ꢋꢟ ꢍꢌ ꢐꢘ ꢘ ꢖꢐ ꢎ ꢐꢏ ꢕꢑꢕ ꢎ ꢒꢚ
Copyright 2003−2007, Texas Instruments Incorporated
www.ti.com
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
(1)
ORDERING INFORMATION
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESIGNATOR
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
PACKAGE−LEAD
ADS1605IPAPT
ADS1605IPAPR
ADS1606IPAPT
ADS1606IPAPR
Tape and Reel, 250
Tape and Reel, 1000
Tape and Reel, 250
Tape and Reel, 1000
ADS1605
ADS1606
HTQFP−64
HTQFP−64
PAP
PAP
−40°C to +85°C
−40°C to +85°C
ADS1605I
ADS1606I
(1)
For the most current package and ordering information, see the Package Option Addendum at the end of this data sheet, or see the TI web
site at www.ti.com.
PRODUCT FAMILY
ABSOLUTE MAXIMUM RATINGS
(1)
over operating free-air temperature range unless otherwise noted
PRODUCT
ADS1605
ADS1606
ADS1625
ADS1626
RESOLUTION
DATA RATE
5.0MSPS
FIFO?
No
ADS1605, ADS1606
−0.3 to +6
UNIT
16 Bits
16 Bits
18 Bits
18 Bits
AVDD to AGND
V
V
V
V
5.0MSPS
Yes
No
DVDD to DGND
−0.3 to +3.6
1.25MSPS
1.25MSPS
IOVDD to DGND
−0.3 to +6
Yes
AGND to DGND
−0.3 to +0.3
Input Current
100mA, Momentary
10mA, Continuous
−0.3 to AVDD + 0.3
−0.3 to IOVDD + 0.3
+150
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handledwith appropriate precautions. Failure to observe
Input Current
Analog I/O to AGND
Digital I/O to DGND
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Lead Temperature (soldering, 10s)
V
V
proper handling and installation procedures can cause damage.
°C
°C
°C
°C
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
−40 to +105
−60 to +150
+260
(1)
Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not implied.
2
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
ELECTRICAL CHARACTERISTICS
All specifications at −40°C to +85°C, AVDD = 5V, DVDD = IOVDD = 3V, f
= 40MHz, External V
REF
= +3V, 2XMODE = low, V
CM
= 2.0V,
CLK
FIFO disabled, and R
= 37kΩ, unless otherwise noted.
BIAS
PARAMETER TEST CONDITIONS
MIN
TYP
MAX
UNIT
Analog Input
0dBFS
1.467V
1.165V
0.735V
0.147V
V
V
V
V
REF
REF
REF
REF
−2dBFS
−6dBFS
−20dBFS
Differential input voltage (V
(AINP − AINN)
)
IN
Common-mode input voltage (V
(AINP + AINN) / 2
)
CM
2.0
V
0dBFS
−0.1
0.1
4.7
4.2
V
V
Absolute input voltage
(AINP or AINN with respect to AGND)
−2dBFS input and smaller
Dynamic Specifications
f
CLK
Data rate
MSPS
5.0ǒ Ǔ
40MHz
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
= 100kHz, −2dBFS
= 100kHz, −6dBFS
= 100kHz, −20dBFS
= 500kHz, −2dBFS
= 500kHz, −6dBFS
= 500kHz, −20dBFS
= 2MHz, −2dBFS
= 2MHz, −6dBFS
= 2MHz, −20dBFS
= 100kHz, −2dBFS
= 100kHz, −6dBFS
= 100kHz, −20dBFS
= 500kHz, −2dBFS
= 500kHz, −6dBFS
= 500kHz, −20dBFS
= 2MHz, −2dBFS
= 2MHz, −6dBFS
= 2MHz, −20dBFS
= 100kHz, −2dBFS
= 100kHz, −6dBFS
= 100kHz, −20dBFS
= 500kHz, −2dBFS
= 500kHz, −6dBFS
= 500kHz, −20dBFS
= 2MHz, −2dBFS
= 2MHz, −6dBFS
= 2MHz, −20dBFS
88
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
84
62
70
86
83
Signal-to-noise ratio (SNR)
69
84
82
69
−93
−99
−94
−94
−97
−93
−98
−101
−92
86
−85
Total harmonic distortion (THD)
84
62
70
86
83
Signal-to-noise and distortion (SINAD)
69
84
82
69
3
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
ELECTRICAL CHARACTERISTICS (continued)
All specifications at −40°C to +85°C, AVDD = 5V, DVDD = IOVDD = 3V, f
= 40MHz, External V
REF
= +3V, 2XMODE = low, V
CM
= 2.0V,
CLK
FIFO disabled, and R
= 37kΩ, unless otherwise noted.
BIAS
PARAMETER
TEST CONDITIONS
= 100kHz, −2dBFS
MIN
TYP
96
MAX
UNIT
dB
dB
dB
dB
dB
dB
dB
dB
dB
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
f
IN
= 100kHz, −6dBFS
= 100kHz, −20dBFS
= 500kHz, −2dBFS
= 500kHz, −6dBFS
= 500kHz, −20dBFS
= 2MHz, −2dBFS
= 2MHz, −6dBFS
= 2MHz, −20dBFS
101
96
85
95
100
95
Spurious free dynamic range (SFDR)
102
105
96
f
1
f
2
= 1.99MHz, −6dBFS
= 2.00MHz, −6dBFS
Intermodulation distortion (IMD)
−94
4
dB
ns
Aperture delay
Digital Filter Characteristics
f
CLK
Passband
0
MHz
2.2ǒ Ǔ
40MHz
Passband ripple
0.0025
dB
f
CLK
−0.1dB attenuation
−3.0dB attenuation
MHz
2.3ǒ Ǔ
40MHz
Passband transition
f
CLK
MHz
2.45ǒ Ǔ
40MHz
f
f
CLK
CLK
Stop band
MHz
dB
37.2ǒ Ǔ
2.8ǒ Ǔ
40MHz
40MHz
Stop band attenuation
Group delay
72
40MHz
µs
5.2ǒ Ǔ
f
CLK
40MHz
Settling time
To 0.001%
µs
9.4ǒ Ǔ
f
CLK
Static Specifications
Resolution
16
Bits
Bits
No missing codes
Input-referred noise
Integral nonlinearity
Differential nonlinearity
Offset error
16
1.0
0.75
0.25
0.05
1
LSB, rms
LSB
−1.5dBFS signal
LSB
%FSR
ppmFSR/°C
%
Offset error drift
Gain error
0.25
10
Gain error drift
Excluding reference drift
ppm/°C
dB
Common-mode rejection
Power-supply rejection
At dc
At dc
75
65
dB
4
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
ELECTRICAL CHARACTERISTICS (continued)
All specifications at −40°C to +85°C, AVDD = 5V, DVDD = IOVDD = 3V, f
= 40MHz, External V
REF
= +3V, 2XMODE = low, V
CM
= 2.0V,
CLK
FIFO disabled, and R
= 37kΩ, unless otherwise noted.
BIAS
PARAMETER
(1)
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Voltage Reference
= (VREFP − VREFN)
V
REF
2.5
3.75
0.75
2.3
3.0
4.0
1.0
2.5
50
3.2
4.25
1.25
2.8
V
VREFP
VREFN
VMID
V
V
V
V
REF
drift
Internal reference (REFEN = low)
Internal reference (REFEN = low)
ppm/°C
ms
Startup time
Clock Input
Frequency (f
Duty Cycle
15
)
40
50
55
MHz
%
CLK
f
= 40MHz
45
CLK
Digital Input/Output
V
V
V
V
0.7 IOVDD
DGND
IOVDD
V
V
IH
0.3 IOVDD
IL
I
I
= 50µA
= 50µA
IOVDD − 0.5
V
OH
OL
OH
DGND +0.5
10
V
OL
Input leakage
DGND < V
DIGIN
< IOVDD
µA
Power-Supply Requirements
AVDD
DVDD
IOVDD
4.75
2.7
5.25
3.3
5.25
135
105
55
V
V
2.7
V
REFEN = low
REFEN = high
110
85
45
4
mA
mA
mA
mA
AVDD current (I
DVDD current (I
)
AVDD
)
DVDD
IOVDD current (I
)
IOVDD = 3V
6
IOVDD
AVDD = 5V, DVDD = 3V, IOVDD = 3V,
REFEN = high
570
5
710
mW
mW
Power dissipation
PD = low, CLK disabled
Temperature Range
Specified
−40
−40
−60
+85
+105
+150
°C
°C
Operating
Storage
°C
Thermal Resistance, θ
25
°C/W
°C/W
JA
PowerPAD soldered to PCB with 2oz.
trace and copper pad.
θ
0.5
JC
(1)
The specification limits for VREF, VREFP, VREFN, and VMID apply when using the internal or an external reference. The internal reference
voltages are bounded by the limits shown. When using an external reference, the limits indicate the allowable voltages that can be applied to
the reference pins.
5
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
DEFINITIONS
Absolute Input Voltage
Intermodulation Distortion (IMD)
Absolute input voltage, given in volts, is the voltage of
each analog input (AINN or AINP) with respect to
AGND.
IMD, given in dB, is measured while applying two input
signals of the same magnitude, but with slightly different
frequencies. It is calculated as the difference between
the rms amplitude of the input signal to the rms ampli-
tude of the peak spurious signal.
Aperture Delay
Aperture delay is the delay between the rising edge of
CLK and the sampling of the input signal.
Offset Error
Offset Error, given in % of FSR, is the output reading
when the differential input is zero.
Offset Error Drift
Common-Mode Input Voltage
Common-mode input voltage (V ) is the average volt-
CM
age of the analog inputs:
Offset error drift, given in ppm of FSR/_C, is the drift
over temperature of the offset error. The offset error is
specified as the larger of the drift from ambient (T =
25_C) to the minimum or maximum operating tempera-
tures.
(AINP ) AINN)
2
Differential Input Voltage
Differential input voltage (V ) is the voltage difference
IN
between the analog inputs: (AINP−AINN).
Signal-to-Noise Ratio (SNR)
Differential Nonlinearity (DNL)
SNR, given in dB, is the ratio of the rms value of the in-
put signal to the sum of all the frequency components
DNL, given in least-significant bits of the output code
(LSB), is the maximum deviation of the output code step
sizes from the ideal value of 1LSB.
below f
/2 (the Nyquist frequency) excluding the first
CLK
six harmonics of the input signal and the dc component.
Signal-to-Noise and Distortion (SINAD)
Full-Scale Range (FSR)
SINAD, given in dB, is the ratio of the rms value of the
input signal to the sum of all the frequency components
FSR is the difference between the maximum and mini-
mum measurable input signals. FSR = 2 × 1.467V
.
REF
below f
/2 (the Nyquist frequency) including the har-
Gain Error
CLK
monics of the input signal but excluding the dc compo-
nent.
Gain error, given in %, is the error of the full-scale input
signal with respect to the ideal value.
Gain Error Drift
Spurious-Free Dynamic Range (SFDR)
SFDR, given in dB, is the difference between the rms
amplitude of the input signal to the rms amplitude of the
peak spurious signal.
Gain error drift, given in ppm/_C, is the drift over tem-
perature of the gain error. The gain error is specified as
the larger of the drift from ambient (T = 25_C) to the
minimum or maximum operating temperatures.
Total Harmonic Distortion (THD)
THD, given in dB, is the ratio of the sum of the rms value
of the first six harmonics of the input signal to the rms
value of the input signal.
Integral Nonlinearity (INL)
INL, given in least-significant bits of the output code
(LSB), is the maximum deviation of the output codes
from a best fit line.
6
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
PIN ASSIGNMENTS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
AGND
AVDD
AGND
AINN
1
2
3
4
5
6
7
8
9
48 FIFO_LEV[2] (ADS1606 Only)
ADS1605
ADS1606
47
46
FIFO_LEV[1] (ADS1606 Only)
FIFO_LEV[0] (ADS1606 Only)
45 NC
AINP
44 DOUT[15]
43
42
AGND
AVDD
RBIAS
AGND
DOUT[14]
DOUT[13]
TQFP PACKAGE
(TOP VIEW)
41 DOUT[12]
40 DOUT[11]
39 DOUT[10]
PowerPADTM
AVDD 10
11
12
38
37
AGND
AVDD
DOUT[9]
DOUT[8]
REFEN 13
NC 14
36 DOUT[7]
35 DOUT[6]
15
16
34
33
2XMODE
NC
DOUT[5]
DOUT[4]
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Terminal Functions
TERMINAL
NAME
AGND
AVDD
AINN
NO.
TYPE
DESCRIPTION
1, 3, 6, 9, 11, 55, 57
Analog
Analog
Analog ground
2, 7, 10, 12, 58
Analog supply
4
Analog input
Analog input
Analog
Negative analog input
Positive analog input
AINP
5
RBIAS
REFEN
NC
8
13
Terminal for external analog bias setting resistor
Digital input: active low
Not connected
Internal reference enable. Internal pull-down resistor of 170kΩ to DGND.
14,16, 27, 28, 45, 50
These terminals are not connected within the ADS1605/6 and must be left
unconnected.
2XMODE
PD
15
Digital input
Digital input: active low
Digital
Digital filter decimation rate. Internal pull-down resistor of 170kΩ to DGND.
17
18, 26, 52
19, 25, 51, 54
20
Power down all circuitry. Internal pull-up resistor of 170kΩ to DGND.
DVDD
DGND
RESET
CS
Digital supply
Digital
Digital ground
Digital input: active low
Digital input: active low
Digital input: active low
Digital output
Reset digital filter
21
Chip select
RD
22
Read enable
OTR
23
Analog inputs out of range
Data ready on falling edge
Data output. DOUT[15] is the MSB and DOUT[0] is the LSB.
DRDY
DOUT [15:0]
FIFO_LEV[2:0]
24
Digital output: active low
Digital output
29−44
46−48
Digital input
FIFO level (for the ADS1606 only). FIFO_LEV[2] is MSB.
NOTE: These terminals must be left disconnected on the ADS1605.
IOVDD
CLK
53
56
Digital
Digital input
Analog
Digital I/O supply
Clock input
VCAP
VREFN
VMID
59
Terminal for external bypass capacitor connection to internal bias voltage
Negative reference voltage
60, 61
62
Analog
Analog
Midpoint voltage
VREFP
63, 64
Analog
Positive reference voltage
7
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
PARAMETER MEASUREMENT INFORMATION
t2
t1
CLK
t2
t3
t4
t4
DRDY
t6
t5
DOUT[15:0]
Data N
Data N + 1
Data N + 2
NOTE: CS and RD tied low.
Figure 1. Data Retrieval Timing (ADS1605, ADS1606 with FIFO Disabled)
RD, CS
t7
t8
DOUT[15:0]
Figure 2. DOUT Inactive/Active Timing (ADS1605, ADS1606 with FIFO Disabled)
TIMING REQUIREMENTS FOR FIGURE 1 AND FIGURE 2
SYMBOL
DESCRIPTION
MIN
20
1
TYP
25
MAX
1000
50
UNIT
t
1
ns
MHz
ns
CLK period (1/f
)
CLK
1/t
1
40
f
CLK
t
2
10
CLK pulse width, high or low
t
3
10
ns
Rising edge of CLK to DRDY low
t
4
4 t
1
ns
DRDY pulse width high or low
t
10
15
15
15
ns
Falling edge of DRDY to data invalid
5
t
6
ns
Falling edge of DRDY to data valid
t
7
ns
Rising edge of RD and/or CS inactive (high) to DOUT high impedance
Falling edge of RD and/or CS active (low) to DOUT active.
t
8
ns
NOTE: DOUT[15:0] and DRDY load = 10pF.
8
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
CLK
t11
t9
RESET
DRDY
t12
t10
t3
Settled
Data
DOUT[15:0]
NOTE: CS and RD tied low.
Figure 3. Reset TIming (ADS1605, ADS1606 with FIFO Disabled)
TIMING REQUIREMENTS FOR FIGURE 3
SYMBOL
DESCRIPTION
MIN
50
TYP
MAX
UNIT
ns
t
3
10
Rising edge of CLK to DRDY low
t
9
ns
RESET pulse width
t
9
ns
Delay from RESET active (low) to DRDY forced high and DOUT forced low
RESET rising edge to falling edge of CLK
10
t
−5
10
ns
11
DRDY
Cycles
t
12
47
Delay from DOUT active to valid DOUT (settling to 0.001%)
NOTE: DOUT[15:0] and DRDY load = 10pF.
9
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
t1
t2
CLK
t2
t13
t14
DRDY
t15
t16
CS(1
)
t21
t17
t20
R
D
t18
t19
DOUT[15:0]
D1
D2
DL(2)
(1) CS may be tied low.
(2) The number of data readings (DL) is set by the FIFO level.
Figure 4. Data Retrieval Timing (ADS1606 with FIFO Enabled)
RD, CS
t7
t8
DOUT[15:0]
Figure 5. DOUT Inactive/Active Timing (ADS1606 with FIFO Enabled)
TIMING REQUIREMENTS FOR FIGURE 4 AND FIGURE 5
SYMBOL
DESCRIPTION
MIN
20
TYP
MAX
UNIT
t
1
25
1000
ns
ns
ns
CLK period (1/f
)
CLK
t
2
10
CLK pulse width, high or low
t
7
7
7
15
15
Rising edge of RD and/or CS inactive (high) to DOUT high impedance
t
8
ns
ns
Falling edge of RD and/or CS active (low) to DOUT active.
Rising edge of CLK to DRDY high
t
13
12
CLK
Cycles
(1)
t
14
8 × FIFO Level
DRDY period
CLK
Cycles
t
15
1
DRDY positive pulse width
t
0
0
ns
ns
ns
ns
RD high hold time after DRDY goes low
CS low before RD goes low
RD negative pulse width
16
t
17
t
18
10
10
t
19
t
20
t
21
RD positive pulse width
CLK
Cycles
2
0
RD high before DRDY toggles
RD high before CS goes high
ns
NOTE: DOUT[15:0] and DRDY load = 10pF.
(1)
See FIFO section for more details.
10
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
CLK
t11
t9
RESET
t26
t25
DRDY
t23
t24
R
D
Figure 6. Reset Timing (ADS1606 with FIFO Enabled)
TIMING REQUIREMENTS FOR FIGURE 6
SYMBOL
DESCRIPTION
MIN
50
TYP
MAX
UNIT
ns
t
9
RESET pulse width
t
11
−5
10
ns
RESET rising edge to falling edge of CLK
CLK
Cycles
t
8
8
RD pulse low after RESET goes high
23
CLK
Cycles
t
24
RD pulse high before first DRDY pulse after RESET goes high
DRDY low after RESET goes low
CLK
Cycles
t
25
8 × (FIFO level + 1)
DRDY
Cycles
See Table 4
t
26
Delay from RESET high to valid DOUT (settling to 0.001%)
11
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
TYPICAL CHARACTERISTICS
All specifications at T = 25°C, AVDD = 5V, DVDD = IOVDD = 3V, f
CLK
BIAS
= 40MHz, External V
REF
= +3V, 2XMODE = low, V
CM
= 2.0V, and
A
R
= 37kΩ, unless otherwise noted.
SPECTRAL RESPONSE
SPECTRAL RESPONSE
0
20
40
60
80
0
−
fIN = 100kHz, 6dBFS
SNR = 84dB
−
−
−
−
−
−
−
−
20
40
60
80
−
THD = 99dB
SFDR = 101dB
−
−
−
−
−
−
−
−
100
120
140
160
100
120
140
160
0
0
0
0.5
1.0
1.5
2.0
2.5
0
0
0
0.5
1.0
1.5
2.0
2.5
Frequency (MHz)
Frequency (MHz)
SPECTRAL RESPONSE
SPECTRAL RESPONSE
0
0
−
fIN = 500kHz, 2dBFS
SNR = 86dB
THD = 97dB
SFDR = 97dB
−
−
−
−
−
−
−
−
20
40
60
80
20
40
60
80
−
−
−
−
−
−
−
−
−
100
120
140
160
100
120
140
160
0.5
1.0
1.5
2.0
2.5
0.5
1.0
1.5
2.0
2.5
Frequency (MHz)
Frequency (MHz)
SPECTRAL RESPONSE
SPECTRAL RESPONSE
0
0
−
−
−
−
−
−
−
−
20
40
60
80
20
40
60
80
−
−
−
−
−
−
−
−
100
120
140
160
100
120
140
160
0.5
1.0
1.5
2.0
2.5
0.5
1.0
1.5
2.0
2.5
Frequency (MHz)
Frequency (MHz)
12
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All specifications at T = 25°C, AVDD = 5V, DVDD = IOVDD = 3V, f
CLK
BIAS
= 40MHz, External V
REF
= +3V, 2XMODE = low, V = 2.0V, and
CM
A
R
= 37kΩ, unless otherwise noted.
INTERMODULATION RESPONSE
NOISE HISTOGRAM
0
18k
16k
14k
12k
10k
8k
fIN1 = 1.99MHz
fIN2 = 2.00MHz
VIN = 0V
−
−
−
−
20
40
60
80
−
IMD = 94dB
−
−
−
−
100
120
140
160
6k
4k
2k
0
−
−
−
−
−
1.95 1.96 1.97 1.98 1.99 2.00 2.01 2.02 2.03 2.04 2.05
5
4
3
2
1
0
1
2
3
4
5
Output Code (LSB)
Frequency (MHz)
SIGNAL−TO−NOISE RATIO,
TOTAL HARMONIC DISTORTION,
AND SPURIOUS−FREE DYNAMIC RANGE
vs INPUT SIGNALAMPLITUDE
SIGNAL−TO−NOISE RATIO
vs INPUT FREQUENCY
110
100
90
80
70
60
50
40
30
20
10
90
−
= 2dBFS
VIN
85
80
75
70
65
60
−
= 6dBFS
VIN
SFDR
−
= 20dBFS
VIN
THD
SNR
fIN = 100kHz
−
−
−
−
−
−
−
10
70
60
50
40
30
20
0
0.001
0.01
0.1
1
10
Input Signal Amplitude, VIN (dB)
Input Frequency, fIN (MHz)
TOTAL HARMONIC DISTORTION
vs INPUT FREQUENCY
SPURIOUS−FREE DYNAMIC RANGE
vs INPUT FREQUENCY
−
−
−
85
90
95
110
108
106
104
102
100
98
−
VIN
=
6dBFS
−
= 20dBFS
VIN
−
= 2dBFS
VIN
−
2dBFS
VIN
=
−
100
−
105
−
110
−
= 20dBFS
VIN
96
−
VIN
=
6dBFS
0.1
94
92
90
0.001
0.01
1
10
0.001
0.01
0.1
Input Frequency, fIN (MHz)
1
10
Input Frequency, fIN (MHz)
13
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All specifications at T = 25°C, AVDD = 5V, DVDD = IOVDD = 3V, f
CLK
BIAS
= 40MHz, External V
REF
= +3V, 2XMODE = low, V
CM
= 2.0V, and
A
R
= 37kΩ, unless otherwise noted.
SIGNAL−TO−NOISE RATIO
vs INPUT COMMON−MODE VOLTAGE
TOTAL HARMONIC DISTORTION
vs INPUT COMMON−MODE VOLTAGE
−
−
−
−
89
87
85
83
81
79
77
75
65
75
85
95
−
VIN
=
=
2dBFS
6dBFS
−
= 2dBFS
VIN
VIN
−
VIN
−
=
6dBFS
−
105
−
115
125
135
−
−
fIN = 100kHz
1.7
fIN = 100kHz
1.7
1.5
1.9
2.1
2.3
2.5
1.5
1.9
2.1
2.3
2.5
Input Common−Mode Voltage, VCM (V)
Input Common−Mode Voltage, VCM (V)
SPURIOUS−FREE DYNAMIC RANGE
vs INPUT COMMON−MODE VOLTAGE
SIGNAL−TO−NOISE RATIO
vs CLK FREQUENCY
105
100
95
90
85
80
75
70
65
60
55
50
45
40
Ω
BIAS = 30k
R
−
= 6dBFS
VIN
−
= 2dBFS
VIN
Ω
R
BIAS = 37k
BIAS = 45k
RBIAS = 50k
90
Ω
R
85
Ω
80
Ω
BIAS = 60k
R
75
fIN = 100kHz, −6dBFS
70
fIN = 100kHz
1.7
65
1.5
1.9
2.1
2.3
2.5
10
20
30
40
50
60
Input Common−Mode Voltage, VCM (V)
CLK Frequency, fCLK (MHz)
TOTAL HARMONIC DISTORTION
vs CLK FREQUENCY
SPURIOUS−FREE DYNAMIC RANGE
vs CLK FREQUENCY
−
−
−
−
−
−
−
65
110
−
fIN = 100kHz, 6dBFS
−
fIN = 100kHz, 6dBFS
70
75
80
85
90
95
105
100
95
Ω
RBIAS = 60k
Ω
R
BIAS = 30k
Ω
BIAS = 50k
R
Ω
RBIAS = 37k
Ω
RBIAS = 45k
Ω
R
BIAS = 45k
RBIAS = 50k
RBIAS = 60k
90
Ω
85
Ω
Ω
RBIAS = 37k
80
−
−
100
105
Ω
RBIAS = 30k
75
10
20
30
40
50
60
10
20
30
40
50
60
CLK Frequency, fCLK (MHz)
CLK Frequency, fCLK (MHz)
14
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All specifications at T = 25°C, AVDD = 5V, DVDD = IOVDD = 3V, f
CLK
BIAS
= 40MHz, External V
REF
= +3V, 2XMODE = low, V
CM
= 2.0V, and
A
R
= 37kΩ, unless otherwise noted.
SIGNAL−TO−NOISE RATIO
vs TEMPERATURE
TOTAL HARMONIC DISTORTION
vs TEMPERATURE
−
−
−
100
90
80
70
60
50
85
90
95
−
−
VIN
VIN
=
=
2dBFS
6dBFS
−
−
−
VIN
VIN
VIN
=
=
=
20dBFS
2dBFS
6dBFS
−
100
−
105
−
110
−
VIN
=
20dBFS
fIN = 100kHz
fIN = 100kHz
−
−
15
40
10
35
60
85
−
−
15
40
10
35
60
85
_
_
Temperature ( C)
Temperature ( C)
SPURIOUS−FREE DYNAMIC RANGE
vs TEMPERATURE
POWER−SUPPLY CURRENT
vs TEMPERATURE
110
105
100
95
130
120
110
100
90
IAVDD (REFEN = low)
−
= 6dBFS
VIN
IAVDD (REFEN = high)
−
= 20dBFS
VIN
80
70
60
−
= 2dBFS
VIN
IDVDD + IIOVDD
90
50
40
fIN = 100kHz
Ω
DVDD = IOVDD = 3V
60 85
RBIAS = 37k , fCLK = 40MHz
85
30
−
−
−
−
15
40
15
10
35
60
85
40
10
35
_
_
Temperature ( C)
Temperature ( C)
ANALOG SUPPLY CURRENT vs RBIAS
SUPPLY CURRENT vs CLK FREQUENCY
140
130
120
110
100
90
100
80
60
40
20
0
Ω
IAVDD (RBIAS = 37k )
Ω
AVDD (RBIAS = 60k )
I
REFEN = low
REFEN = high
80
IDVDD + IIOVDD
70
60
AVDD = 5V, DVDD = IOVDD = 3V, REFEN = High
50
30
35
40
45
50
55
60
10
20
30
40
50
Ω
RBIAS (k )
CLK Frequency, fCLK (MHz)
15
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
TYPICAL CHARACTERISTICS (continued)
All specifications at T = 25°C, AVDD = 5V, DVDD = IOVDD = 3V, f
CLK
BIAS
= 40MHz, External V
REF
= +3V, 2XMODE = low, V
CM
= 2.0V, and
A
R
= 37kΩ, unless otherwise noted.
INTEGRAL NONLINEARITY
DIFFERENTIAL NONLINEARITY
0.5
1.0
0.8
0.6
0.4
0.2
0
−
fIN = 100Hz, 1.5dBFS
−
fIN = 100Hz, 1.5dBFS
0.4
0.3
0.2
0.1
0
−
0.1
0.2
0.3
0.4
0.5
−
0.2
0.4
0.6
0.8
1.0
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
25k 20k 15k 10k 5k
0
5k 10k 15k 20k 25k
25k 20k 15k 10k 5k
0
5k 10k 15k 20k 25k
Output Code (LSB)
Output Code (LSB)
16
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
tive digital output code of 7FFFh. Likewise, the most neg-
OVERVIEW
ative measurable differential input is –1.467V
produces the most negative digital output code of 8000h.
, which
The ADS1605 and ADS1606 are high-performance delta-
sigma ADCs with a default oversampling ratio of 8. The
modulator uses an inherently stable 2-1-1 pipelined delta-
sigma modulator architecture incorporating proprietary
circuitry that allows for very linear high-speed operation.
The modulator samples the input signal at 40MSPS
REF
The ADS1605/6 supports a very wide range of input sig-
nals. For V
= 3V, the full-scale input voltages are
REF
4.4V. Having such a wide input range makes out-of-
range signals unlikely. However, should an out-of-range
signal occur, the digital output OTR will go high.
(when f
= 40MHz). A low-ripple linear phase digital fil-
CLK
ter decimates the modulator output to provide data output
word rates of 5MSPS with a signal passband out to
2.45MHz. The 2X mode, enabled by a digital I/O pin,
doubles the data rate to 10MSPS by reducing the over-
sampling ratio to 4. See the 2X Mode section for more de-
tails.
To achieve the highest analog performance, it is recom-
mended that the inputs be limited to 1.165V
REF
(−2dBFS). For V
= 3V, the corresponding recom-
REF
mended input range is 3.78V.
The analog inputs must be driven with a differential signal
to achieve optimum performance. The recommended
common-mode voltage of the input signal,
AINP ) AINN
Conceptually, the modulator and digital filter measure the
differential input signal, V = (AINP – AINN), against the
IN
scaled differential reference, V
= (VREFP – VREFN),
REF
VCM
+
, is 2.0V. For signals larger than
2
as shown in Figure 7. The voltage reference can either be
generated internally or supplied externally. An 16-bit paral-
lel data bus, designed for direct connection to DSPs, out-
puts the data. A separate power supply for the I/O allows
flexibility for interfacing to different logic families. Out-of-
range conditions are indicated with a dedicated digital out-
put pin. Analog power dissipation is controlled using an
external resistor. This allows reduced dissipation when
operating at slower speeds. When not in use, power con-
sumption can be dramatically reduced using the PD pin.
−2dBFS, the input common-mode voltage needs to be
raised in order to meet the absolute input voltage specifi-
cations. The Typical Characteristics show how perfor-
mance varies with input common-mode voltage.
In addition to the differential and common-mode input volt-
ages, the absolute input voltage is also important. This is
the voltage on either input (AINP or AINN) with respect to
AGND. The range for this voltage is:
* 0.1V t (AINN or AINP) t 4.6V
The ADS1606 incorporates an adjustable FIFO buffer for
the output data. The level of the FIFO is set by the
FIFO_LEV[2:0] pins. Other than the FIFO buffer, the
ADS1605 and ADS1606 are identical, and are referred to
together in this data sheet as the ADS1605/6.
If either input is taken below –0.1V, ESD protection diodes
on the inputs will turn on. Exceeding 4.6V on either input
will result in degradation in the linearity performance. ESD
protection diodes will also turn on if the inputs are taken
above AVDD (+5V).
ANALOG INPUTS (AINP, AINN)
For signals below –2dBFS, the recommended absolute
input voltage is:
The ADS1605/6 measures the differential signal,
V
V
= (AINP − AINN), against the differential reference,
IN
* 0.1V t (AINN or AINP) t 4.2V
= (VREFP – VREFN). The reference is scaled inter-
REF
nally so that the full-scale differential input voltage is
Keeping the inputs within this range provides for optimum
performance.
1.467V
ential input is 1.467V
. That is, the most positive measurable differ-
REF
, which produces the most posi-
REF
VREFP VREFN
IOVDD
Σ
VREF
1.467
OTR
1.467VREF
ADS1606 Only
Parallel
Interface
DOUT[15:0]
FIFO
Digital
Filter
VIN
AINP
AINN
Σ∆
Modulator
Σ
FIFO_LEV[2:0]
2XMODE
Figure 7. Conceptual Block Diagram
17
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
INPUT CIRCUITRY
AGND, improve linearity and should be placed as close
to the pins as possible. Place the drivers close to the in-
puts and use good capacitor bypass techniques on their
supplies; usually a smaller high-quality ceramic capaci-
tor in parallel with a larger capacitor. Keep the resistanc-
es used in the driver circuits low—thermal noise in the
driver circuits degrades the overall noise performance.
When the signal can be ac-coupled to the ADS1605/6
inputs, a simple RC filter can set the input common
mode voltage. The ADS1605/6 is a high-speed, high-
performance ADC. Special care must be taken when
selecting the test equipment and setup used with this
device. Pay particular attention to the signal sources to
ensure they do not limit performance when measuring
the ADS1605/6.
The ADS1605/6 uses switched-capacitor circuitry to
measure the input voltage. Internal capacitors are
charged by the inputs and then discharged internally
with this cycle repeating at the frequency of CLK.
Figure 8 shows a conceptual diagram of these circuits.
Switches S2 represent the net effect of the modulator
circuitry in discharging the sampling capacitors; the ac-
tual implementation is different. The timing for switches
S1 and S2 is shown in Figure 9.
ADS1605
ADS1606
S1
AINP
AINN
S2
10pF
8pF
Ω
392
VMID
40pF
Ω
Ω
392
392
V
IN
S1
−
2
µ
0.01
1k
F
Ω
49.9
S2
AINP
OPA2822
(2)
10pF
8pF
(1)
V
CM
100pF
Ω
Ω
µ
F
392
1
VMID
(2)
AGND
Ω
392
ADS1605
ADS1606
(1)
(3)
V
100pF
CM
(2)
40pF
Ω
392
V
Ω
1k
IN
Figure 8. Conceptual Diagram of Internal
Circuitry Connected to the Analog Inputs
2
µ
0.01
F
Ω
49.9
AINN
OPA2822
Ω
392
(2)
(1)
CM
V
100pF
tSAMPLE = 1/fCLK
Ω
µ
F
392
1
AGND
On
Off
S1
S2
(1) Recommended VCM = 2.0V.
(2) Optional ac−coupling circuit provides common−mode input voltage.
≤
(3) Increase to 390pF when fIN 100kHz for improved SNR and THD.
On
Off
Figure 10. Recommended Driver Circuit Using the
OPA2822
Figure 9. Timing for the Switches in Figure 2
22pF
Ω
Ω
24.9
24.9
DRIVING THE INPUTS
AINP
Ω
392
100pF
100pF
The external circuits driving the ADS1605/6 inputs must
be able to handle the load presented by the switching
capacitors within the ADS1605/6. The input switches
S1 in Figure 8 are closed approximately one half of the
Ω
Ω
392
392
−
VIN
ADS1605
ADS1606
VCM
THS4503
+VIN
Ω
392
sampling period, t
, allowing only ≈12ns for the in-
sample
AINN
ternal capacitors to be charged by the inputs, when f
= 40MHz.
CLK
100pF
22pF
Figure 10 and Figure 11 show the recommended cir-
cuits when using single-ended or differential op amps,
respectively. The analog inputs must be driven differen-
tially to achieve optimum performance. The external ca-
pacitors, between the inputs and from each input to
Figure 11. Recommended Driver Circuits Using
the THS4503 Differential Amplifier
18
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
REFERENCE INPUTS (VREFN, VREFP, VMID)
in the Electrical Characteristics table. Typically VREFP
= 4V, VMID = 2.5V and VREFN = 1V. The external cir-
cuitry must be capable of providing both a dc and a tran-
sient current. Figure 13 shows a simplified diagram of
the internal circuitry of the reference when the internal
reference is disabled. As with the input circuitry,
switches S1 and S2 open and close as shown in
Figure 9.
The ADS1605/6 can operate from an internal or exter-
nal voltage reference. In either case, the reference volt-
age V
VREFN and VREFP: V
is set by the differential voltage between
REF
= (VREFP – VREFN).
REF
VREFP and VREFN each use two pins, which should
be shorted together. VMID equals approximately 2.5V
and is used by the modulator. VCAP connects to an in-
ternal node and must also be bypassed with an external
capacitor. For the best analog performance, it is recom-
ADS1605
ADS1606
mended that an external reference voltage (V
3.0V be used.
) of
REF
S1
VREFP
VREFP
S2
INTERNAL REFERENCE (REFEN = LOW)
Ω
300
50pF
To use the internal reference, set the REFEN pin low.
This activates the internal circuitry that generates the
reference voltages. The internal reference voltages are
applied to the pins. Good bypassing of the reference
pins is critical to achieve optimum performance and is
done by placing the bypass capacitors as close to the
pins as possible. Figure 12 shows the recommended
bypass capacitor values. Use high quality ceramic ca-
pacitors for the smaller values. Avoid loading the inter-
nal reference with external circuitry. If the ADS1605/6
internal reference is to be used by other circuitry, buffer
the reference voltages to prevent directly loading the
reference pins.
VREFN
VREFN
S1
Figure 13. Conceptual Internal Circuitry for the
Reference When REFEN = High
Figure 14 shows the recommended circuitry for driving
these reference inputs. Keep the resistances used in
the buffer circuits low to prevent excessive thermal
noise from degrading performance. Layout of these cir-
cuits is critical, make sure to follow good high-speed
layout practices. Place the buffers and especially the
bypass capacitors as close to the pins as possible.
VCAP is unaffected by the setting on REFEN and must
be bypassed when using the internal or an external ref-
erence.
ADS1605
ADS1606
VREFP
µ
µ
0.1 F
VREFP
10 F
Ω
392
µ
0.001
F
µ
22 F
ADS1605
ADS1606
VMID
µ
22 F
µ
0.1 F
VREFP
VREFP
OPA2822
µ
µ
0.1 F
10 F
µ
10
F
4V
0.1µF
Ω
392
µ
22 F
µ
0.1
F
VREFN
VREFN
µ
0.001
F
µ
22 F
µ
22
F
µ
µ
0.1 F
10 F
VMID
OPA2822
µ
10
F
2.5V
µ
0.1
F
VCAP
µ
0.1 F
Ω
392
µ
0.001
F
AGND
22µF
VREFN
VREFN
Figure 12. Reference Bypassing When Using the
Internal Reference
OPA2822
1V
µ
µ
µ
10
F
0.1
0.1
F
F
EXTERNAL REFERENCE (REFEN = HIGH)
VCAP
To use an external reference, set the REFEN pin high.
This deactivates the internal generators for VREFP,
VREFN and VMID, and saves approximately 25mA of
current on the analog supply (AVDD). The voltages ap-
plied to these pins must be within the values specified
AGND
Figure 14. Recommended Buffer Circuit When
Using an External Reference
19
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
CLOCK INPUT (CLK)
Likewise, when the input is negative out-of-range by go-
ing below the negative full-scale value of –1.467V
,
REF
The ADS1605/6 requires an external clock signal to be
applied to the CLK input pin. The sampling of the modu-
lator is controlled by this clock signal. As with any high-
speed data converter, a high quality clock is essential
for optimum performance. Crystal clock oscillators are
the recommended CLK source; other sources such as
frequency synthesizers are usually not adequate. Make
sure to avoid excess ringing on the CLK input; keeping
the trace as short as possible will help.
the output clips to 8000h and the OTR output goes high.
The OTR remains high while the input signal is out-of-
range.
Table 2. Output Code Versus Input Signal
INPUT SIGNAL
(INP – INN)
IDEAL OUTPUT
(1)
CODE
OTR
≥+1.467V
(> 0dB)
7FFF
1
0
0
REF
H
Measuring high frequency, large amplitude signals re-
quires tight control of clock jitter. The uncertainty during
sampling of the input from clock jitter limits the maxi-
mum achievable SNR. This effect becomes more pro-
nounced with higher frequency and larger magnitude in-
puts. Fortunately, the ADS1605/6 oversampling
topology reduces clock jitter sensitivity over that of Ny-
quist rate converters like pipeline and successive
1.467V
(0dB)
7FFF
H
REF
0001
+1.467VREF
H
2
15 * 1
0
0000
0
0
H
FFFF
−1.467VREF
H
2
15 * 1
8000
0
1
215
H
ǒ
Ǔ
Ǹ
−1.467VREF
approximation converters by a factor of 8.
215 * 1
In order to not limit the ADS1605/6 SNR performance,
keep the jitter on the clock source below the values
shown in Table 1. When measuring lower frequency
and lower amplitude inputs, more CLK jitter can be tol-
erated. In determining the allowable clock source jitter,
select the worst-case input (highest frequency, largest
amplitude) that will be seen in the application.
8000
215
215 * 1
H
ǒ
Ǔ
v −1.467VREF
(1)
Excludes effects of noise, INL, offset and gain errors.
OUT-OF-RANGE INDICATION (OTR)
If the output code on DOUT[15:0] exceeds the positive
or negative full-scale, the out-of-range digital output
OTR will go high on the falling edge of DRDY. When the
output code returns within the full-scale range, OTR re-
turns low on the falling edge of DRDY.
Table 1. Maximum Allowable Clock Source Jitter
for Different Input Signal Frequencies and
Amplitude
MAXIMUM
ALLOWABLE
CLOCK SOURCE
JITTER
INPUT SIGNAL
DATA RETRIEVAL
MAXIMUM
MAXIMUM
Data retrieval is controlled through a simple parallel in-
terface. The falling edge of the DRDY output indicates
new data are available. To activate the output bus, both
CS and RD must be low, as shown in Table 3. Make
sure the DOUT bus does not drive heavy loads (>
20pF), as this will degrade performance. Use an exter-
nal buffer when driving an edge connector or cables.
FREQUENCY
AMPLITUDE
2MHz
−2dB
−20dB
−2dB
1.9ps
14ps
3.8ps
28ps
7.6ps
57ps
38ps
285ps
2MHz
1MHz
1MHz
−20dB
−2dB
500kHz
500kHz
100kHz
100kHz
−20dB
−2dB
Table 3. Truth Table for CS and RD
CS
0
RD
0
DOUT[15:0]
Active
−20dB
0
1
High impedance
High impedance
High impedance
1
0
DATA FORMAT
1
1
The 16-bit output data are in binary two’s complement
format as shown in Table 2. When the input is positive
out-of-range, exceeding the positive full-scale value of
1.467V
output goes high.
, the output clips to all 7FFFh and the OTR
REF
20
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
RESETTING THE ADS1605
RESETTING THE ADS1606
The ADS1605 and ADS1606 (with FIFO disabled) are
asynchronously reset when the RESET pin is taken low.
During reset, all of the digital circuits are cleared,
DOUT[15:0] are forced low, and DRDY forced high. It
is recommended that the RESET pin be released on the
falling edge of CLK. Afterwards, DRDY goes low on the
second rising edge of CLK. Allow 47 DRDY cycles for
the digital filter to settle before retrieving data. See
Figure 3 for the timing specifications.
The ADS1606 with the FIFO enabled requires a differ-
ent reset sequence than the ADS1605, as shown in
Figure 16. Ignore any DRDY toggles that occur while
RESET is low. Release RESET on the rising edge of
CLK, then afterwards toggle RD to complete the reset
sequence.
CLK
Reset can be used to synchronize multiple ADS1605s.
All devices to be synchronized must use a common
CLK input. With the CLK inputs running, pulse RESET
on the falling edge of CLK, as shown in Figure 15. After-
wards, the converters will be converting synchronously
with the DRDY outputs updating simultaneously. After
RESET
Ignore
t26
DRDY
synchronization, allow 47 DRDY cycles (t ) for output
12
data to fully settle.
R
D
Toggle RD to complete reset sequence
ADS16051
RESET
Clock
RESET
CLK
DRDY
DRDY1
Figure 16. Resetting the ADS1606 with the FIFO
Enabled
DOUT[15:0]
DOUT[15:0]1
After resetting, the settling time for the ADS1606 is 47
CLK cycles, regardless of the FIFO level. Therefore, for
higher FIFO levels, it takes fewer DRDY cycles to settle
because the DRDY period is longer. Table 4 shows the
number of DRDY cycles required to settle for each FIFO
level.
ADS16052
RESET
CLK
DRDY
DRDY2
DOUT[15:0]
DOUT[15:0]2
CLK
Table 4. ADS1606 Reset Settling
FILTER SETTLING TIME AFTER RESET
RESET
t12
(t in units of DRDY cycles )
26
FIFO LEVEL
2
4
24
12
8
DRDY1
6
Settled
Data
DOUT[15:0]1
8
6
10
12
14
5
DRDY2
4
4
Settled
Data
DOUT[15:0]2
Synchronized
Figure 15. Synchronizing Multiple Converters
21
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
SETTLING TIME
IMPULSE RESPONSE
The settling time is an important consideration when
measuring signals with large steps or when using a mul-
tiplexer in front of the analog inputs. The ADS1605/6
digital filter requires time for an instantaneous change
in signal level to propagate to the output.
Figure 18 plots the normalized response for an input
applied at t = 0 with 2XMODE = low. The X-axis units of
time are DRDY cycles (for the ADS1605 or the ADS1606
with FIFO disabled). As shown in Figure 18, the peak of
the impulse takes 26 DRDY cycles to propagate to the
output. For f
= 40MHz, a DRDY cycle is 0.2µs in
CLK
Be sure to allow the filter time to settle after applying a
large step in the input signal, switching the channel on
a multiplexer placed in front of the inputs, resetting the
ADS1605/6, or exiting the power-down mode,
duration and the propagation time (or group delay) is 26
× 0.2µs = 5.2µs.
Figure 17 shows the settling error as a function of time
for a full-scale signal step applied at t = 0 with
2XMODE = low. This figure uses DRDY cycles (for the
ADS1605 or the ADS1606 with FIFO disabled) for the
time scale (X-axis). After 47 DRDY cycles, the settling
1.0
0.8
0.6
0.4
0.2
0
error drops below 0.001%. For f
= 40MHz, this cor-
CLK
responds to a settling time of 9.4µs.
101
100
−
−
0.2
0.4
0
5
10
15
20
25
30
35
40
45 50
Time (DRDY cycles)
10−1
10−2
10−3
10−4
Figure 18. Impulse Response
25
30
35
40
45
50
Settling Time (DRDY cycles)
Figure 17. Settling Time
22
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
FREQUENCY RESPONSE
0.0025
0.0020
0.0015
0.0010
0.0005
0
The linear phase FIR digital filter sets the overall fre-
quency response. The decimation rate is set to 8
(2XMODE = low) for all the figures shown in this section.
Figure 19 shows the frequency response from dc to
fCLK = 40MHz
20MHz for f
= 40MHz. The frequency response of
CLK
the ADS1605/6 filter scales directly with CLK frequency.
For example, if the CLK frequency is decreased by half
(to 20MHz), the values on the X-axis in Figure 19 would
need to be scaled by half, with the span becoming dc to
10MHz.
−
−
−
−
0.0005
0.0010
0.0015
0.0020
Figure 20 shows the passband ripple from dc to 2.2MHz
0
0.5
1.0
1.5
2.0
2.5
(f
= 40MHz). Figure 21 shows a closer view of the
CLK
Frequency (MHz)
passband transition by plotting the response from
2.0MHz to 2.5MHz (f = 40MHz).
CLK
The overall frequency response repeats at multiples of
the CLK frequency. To help illustrate this, Figure 22
Figure 20. Passband Ripple
shows the response out to 120MHz (f
= 40MHz).
CLK
Notice how the passband response repeats at 40MHz,
80MHz and 120MHz; it is important to consider this
when there is high-frequency noise present with the sig-
nal. The modulator bandwidth extends to 100MHz.
High-frequency noise around 40MHz and 80MHz will
not be attenuated by either the modulator or the digital
filter. This noise will alias back in-band and reduce the
overall SNR performance unless it is filtered out prior to
the ADS1605/6. To prevent this, place an anti-alias filter
in front of the ADS1605/6 that rolls off before 37MHz.
1
0
−
−
−
−
−
−
−
1
2
3
4
5
6
7
fCLK = 40MHz
20
2.0 2.05 2.1 2.15 2.2 2.25 2.3 2.35 2.4 2.45 2.5
Frequency (MHz)
0
−
−
−
−
20
40
60
80
Figure 21. Passband Transition
20
0
−
−
100
120
fCLK = 40MHz
0
2
4
6
8
10
12 14
16 18
20
−
−
−
−
20
40
60
80
Frequency (MHz)
Figure 19. Frequency Response
−
100
0
20
40
60
80
100
120
Frequency (MHz)
Figure 22. Frequency Response Out to 120MHz
23
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
FIFO (ADS1606 ONLY)
present on the data output pins. Continue this way until
all the data have been read from the FIFO, making sure
to take RD high when complete. Afterwards, wait until
DRDY toggles and repeat the readback cycle.
Figure 23 shows an example readback when
FIFO_LEV[2:0] = 010 (level = 4).
The ADS1606 includes an adjustable level first-in first-
out buffer (FIFO) for the output data. The FIFO allows
data to be temporarily stored within the ADS1606 to
provide more flexibility for the host controller when re-
trieving data. Pins FIFO_LEV[2:0] set the level or depth
of the FIFO. Note that these pins must be left uncon-
nected on the ADS1605. The FIFO is enabled by setting
at least one of the FIFO_LEV inputs high. Table 5
shows the corresponding FIFO level and DRDY period
for the different combinations of FIFO_LEV[2:0] set-
tings. For the best performance when using the FIFO,
it is recommended to:
Readback considerations
The exact number of data readings set by the FIFO lev-
el must be read back each time DRDY toggles. The one
exception is that readback can be skipped entirely. In
this case, the DRDY period increases to 128 CLK peri-
od. Figure 24 shows an example when readback is
skipped with the FIFO level = 4. Do not read back more
or less readings from the FIFO than set by the level.
This interrupts the FIFO operation and can cause
DRDY to stay low indefinitely. If this occurs, the RESET
pin must be toggled followed by a RD pulse. This resets
the ADS1606 FIFO and also the digital filter, which then
must settle afterwards before valid data is ready. See
the section, Resetting the ADS1606, for more details.
Also note that the RD signal is independent of the CS
signal. Therefore, when multiple devices are used, the
RD signal should not be shared. Alternatively, individual
RD signals can be generated by performing an OR op-
eration with the CS signal.
1. Set IOVDD = 3V.
2. Synchronize data retrieval with CLK.
3. Minimize loading on outputs DOUT[15:0].
4. Ensure rise and fall times on CLK and RD are 1ns
or longer.
Table 5. FIFO Buffer Level Settings for the
ADS1606
FIFO_LEV[2:0]
FIFO BUFFER LEVEL
DRDY PERIOD
000
0: disabled,
8/f
CLK
operates like ADS1605
001
010
011
100
101
110
111
2
4
16/f
32/f
48/f
64/f
80/f
96/f
CLK
CLK
CLK
CLK
CLK
CLK
Setting the FIFO Level
The FIFO level setting is usually a static selection that
is set when power is first applied to the ADS1606. If the
FIFO level needs to be changed after powerup, there
are two options. One is to asynchronously set the new
value on pin FIFO_LEV[2:0] then toggle RESET. Re-
member that the ADS1606 will need to settle after re-
setting. See the section, Resetting the ADS1606, for
more details. The other option avoids requiring a reset,
but needs synchronization of the FIFO level change
with the readback. The FIFO_LEV[2:0] pins have to be
changed after RD goes high after reading the first data,
but before RD goes low to read the last data from the
FIFO. The new FIFO level becomes active immediately
and the DRDY period adjusts accordingly. When de-
creasing the FIFO level this way, make sure to give ade-
quate time for readback of the data before setting the
new, smaller level. Figure 25 shows an example of a
synchronized FIFO level change from 4 to 8.
6
8
10
12
14
112/f
CLK
FIFO Operation
The ADS1606 FIFO collects the number of output read-
ings set by the level corresponding to the
FIFO_LEV[2:0] setting. When the specified level is
reached, DRDY is pulsed high, indicating the data in the
FIFO are ready to be read. The DRDY period is a func-
tion of the FIFO level, as shown in Table 5. To read the
data, make sure CS is low (it is acceptable to tie it low)
and then take RD low. The first, or oldest, data will be
presented on the data output pins. After reading this
data, advance to the next data reading by toggling RD.
On the next falling edge of RD, the second data are
DRDY
CS(1)
RD
(2)
Data1
Data2
Data3
Data4
DOUT[15:0]
(1) CS can be tied low.
(2) Data1 is the oldest data and Data4 is the most recent.
Figure 23. Example of FIFO Readback when FIFO Level = 4
24
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
32/fCLK
128/fCLK
DRDY
RD
Figure 24. Example of Skipping Readback when FIFO Level = 4
32/fCLK
64/fCLK
DRDY
RD
FIFO_LEV[2:0]
010 (Level = 4)
100 (Level = 8)
Change FIFO_LEV[2:0] here
Figure 25. Example of Synchronized Change of FIFO Level from 4 to 8
ANALOG POWER DISSIPATION
Table 6. Recommended R
Resistor Values for
BIAS
Different CLK Frequencies
An external resistor connected between the RBIAS pin
and the analog ground sets the analog current level, as
shown in Figure 26. The current is inversely proportion-
al to the resistor value. Table 6 shows the recom-
TYPICAL POWER
DISSIPATION WITH REFEN
HIGH
DATA
RATE
f
R
BIAS
CLK
16MHz
24MHz
32MHz
40MHz
2MHz
3MHz
4MHz
5MHz
60kΩ
50kΩ
45kΩ
37kΩ
315mW
400mW
475mW
570mW
mended values of R
for different CLK frequencies.
BIAS
Notice that the analog current can be reduced when us-
ing a slower frequency CLK input because the modula-
tor has more time to settle. Avoid adding any capaci-
tance in parallel to R
the internal circuitry used to set the biasing.
, since this will interfere with
BIAS
POWER DOWN (PD)
When not in use, the ADS1605/6 can be powered down
by taking the PD pin low. All circuitry will be shutdown,
including the voltage reference. To minimize the digital
current during power down, stop the clock signal sup-
plied to the CLK input. There is an internal pull-up resis-
tor of 170kΩ on the PD pin, but it is recommended that
this pin be connected to IOVDD if not used. If using the
ADS1606 with the FIFO enabled, issue a reset after ex-
iting power-down mode. Make sure to allow time for the
reference to start up after exiting power-down mode.
The internal reference typically requires 15ms. After the
reference has stabilized, allow at least 100 DRDY
cycles for the modulator and digital filter to settle before
retrieving data.
ADS1605
ADS1606
RBIAS
RBIAS
AGND
Figure 26. External Resistor Used to Set Analog
Power Dissipation
25
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
POWER SUPPLIES
main supply bus should also be bypassed with a bank
of capacitors from 47µF to 0.1µF, as shown.
Three supplies are used on the ADS1605/6: analog
(AVDD), digital (DVDD) and digital I/O (IOVDD). Each
supply must be suitably bypassed to achieve the best
performance. It is recommended that a 1µF and 0.1µF
ceramic capacitor be placed as close to each supply pin
as possible. Connect each supply-pin bypass capacitor
to the associated ground, as shown in Figure 27. Each
The IO and digital supplies (IOVDD and DVDD) can be
connected together when using the same voltage. In
this case, only one bank of 47µF to 0.1µF capacitors is
needed on the main supply bus, though each supply pin
must still be bypassed with a 1µF and 0.1µF ceramic ca-
pacitor.
DVDD
µ
µ
µ
1 F
µ
0.1 F
47 F
4.7 F
IOVDD
AVDD
µ
µ
1 F
47 F
µ
µ
0.1 F
4.7 F
CP
CP
CP
µ
µ
0.1 F
4.7 F
µ
47 F
µ
1 F
58
57
55
54
53
52
51
1
AGND
AVDD
CP
2
3
If using separate analog and
digital ground planes, connect
together on the ADS1605/6 PCB.
6
AGND
CP
ADS1605
ADS1606
AVDD
AGND
7
9
DGND
AGND
µ
µ
NOTE: CP = 1 F 0.1 F
CP
AVDD
AGND
10
11
CP
12
AVDD
18
19
25
CP
26
CP
Figure 27. Recommended Power-Supply Bypassing
26
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
2X MODE
Two approaches can be used for the ground planes: ei-
ther a single common plane; or two separate planes,
one for the analog grounds and one for the digital
grounds. When using only one common plane, isolate
the flow of current on pin 57 from pin 1; use breaks on
the ground plane to accomplish this. Pin 57 carries the
switching current from the analog clocking for the mod-
ulator and can corrupt the quiet analog ground on pin 1.
When using two planes, it is recommended that they be
tied together right at the PCB. Do not try to connect the
ground planes together after running separately
through edge connectors or cables as this reduces per-
formance and increases the likelihood of latchup.
The 2XMODE digital input determines the performance
(16-bit or 14-bit) by setting the oversampling ratio.
When 2XMODE = low, the oversampling ratio = 8 for
16-bit performance. When 2XMODE = high, the over-
sampling ratio = 4 for 14-bit performance. Note that
when 2XMODE is high, all 16 bits of DOUT remain ac-
tive. Decreasing the oversampling ratio from 8 to 4
doubles the data rate in 2X mode. For f
= 40MHz,
CLK
the data rate then becomes 10MSPS. In addition, the
group delay decreases to 0.9µs and the settling time be-
comes 1.3µs or 13 DRDY cycles. With the reduced
oversampling in 2X mode, the noise increases. Typical
SNR performance degrades by 14dB. THD remains
approximately the same. There is an internal pull-down
resistor of 170kΩ on the 2XMODE; however, it is rec-
ommended this pin be forced either high or low. For
more information on the performance of the 2X mode,
see application note Operating the ADS1605 and
ADS1606 in 2X Mode: 10MSPS (SLAA180), available
for download at www.ti.com.
In general, keep the resistances used in the driving cir-
cuits for the inputs and reference low to prevent excess
thermal noise from degrading overall performance.
Avoid having the ADS1605/6 digital outputs drive heavy
loads. Buffers on the outputs are recommended unless
the ADS1605/6 is connected directly to a DSP or con-
troller situated nearby. Additionally, make sure the digi-
tal inputs are driven with clean signals as ringing on the
inputs can introduce noise.
The ADS1605/6 uses TI PowerPAD technology. The
PowerPAD is physically connected to the substrate of
the silicon inside the package and must be soldered to
the analog ground plane on the PCB using the exposed
metal pad underneath the package for proper heat
dissipation. Please refer to application report
SLMA002, located at www.ti.com, for more details on
the PowerPAD package.
LAYOUT ISSUES
The ADS1605/6 is a very high-speed, high-resolution
data converter. In order to achieve the maximum perfor-
mance, careful attention must be given to the printed
circuit board (PCB) layout. Use good high-speed tech-
niques for all circuitry. Critical capacitors should be
placed close to pins as possible. These include capaci-
tors directly connected to the analog and reference in-
puts and the power supplies. Make sure to also properly
bypass all circuitry driving the inputs and references.
27
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
INTERFACING THE ADS1606 TO THE
TMS320C6000
APPLICATIONS INFORMATION
INTERFACING THE ADS1605 TO THE
TMS320C6000
Figure 29 illustrates how to directly connect the
ADS1606 to the TMS320C6000 DSP. The processor
controls reading using output ARE. The ADS1606 is
permanently selected by grounding the CS pin. The
ADS1606 16-bit data output bus is directly connected
to the TMS320C6000 data bus. The data ready output
from the ADS1606, DRDY, drives interrupt EXT_INT7
on the TMS320C6000.
Figure 28 illustrates how to directly connect the
ADS1605 to the TMS320C6000 DSP. The processor
controls reading using output ARE. The ADS1605 is se-
lected using the DSP control output, CE2. The
ADS1605 16-bit data output bus is directly connected
to the TMS320C6000 data bus. The data ready output
from the ADS1605, DRDY, drives interrupt EXT_INT7
on the TMS320C6000.
ADS1606
TMS320C6000
16
DOUT[15:0]
XD[15:0]
ADS1605
TMS320C6000
16
DOUT[15:0]
XD[15:0]
DRDY
CS
EXT_INT7
DRDY
CS
EXT_INT7
CE2
RD
ARE
RD
ARE
Figure 29. ADS1606—TMS320C6000 Interface
Connection
Figure 28. ADS1605—TMS320C6000 Interface
Connection
28
ꢉ ꢃꢠ ꢡꢢ ꢣꢤ
ꢉ ꢃꢠ ꢡꢢ ꢣꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
INTERFACING THE ADS1605 TO THE
TMS320C5400
INTERFACING THE ADS1606 TO THE
TMS320C5400
Figure 30 illustrates how to connect the ADS1605 to the
TMS320C5400 DSP. The processor controls the read-
ing using the outputs R/W and IS. The I/O space select
signal (IS) is optional and is used to prevent the
ADS1605 RD input from being strobed when the DSP
is accessing other external memory spaces (address or
data). This can help reduce the possibility of digital
noise coupling into the ADS1605. When not using this
signal, replace NAND gate U1 with an inverter between
R/W and RD. Two signals, IOSTRB and A15, combine
using NAND gate U2 to select the ADS1605. If there are
no additional devices connected to the TMS320C5400
I/O space, U2 can be eliminated. Simply connect
IOSTRB directly to CS. The ADS1605 16-bit data out-
put bus is directly connected to the TMS320C5400 data
bus. The data ready output from the ADS1605, DRDY,
drives interrupt INT3 on the TMS320C5400.
Figure 31 illustrates how to directly connect the
ADS1606 to the TMS320C5400 DSP. The processor
controls reading using outputs R/W and IS. The
ADS1606 is permanently selected by grounding the CS
pin. If there are any additional devices connected to
theTMS320C5400 I/O space, address decode logic will
be required between the ADC and the DSP to prevent
data bus contention and ensure only one device at a
time is selected. The ADS1606 16-bit data output bus
is directly connected to the TMS320C5400 data bus.
The data ready output from the ADS1606, DRDY,
drives interrupt INT3 on the TMS320C5400.
ADS1606
TMS320C5400
16
DOUT[15:0]
D[15:0]
DRDY
CS
INT3
ADS1605
TMS320C5400
16
DOUT[15:0]
D[15:0]
R/W
IS
U1
RD
DRDY
CS
INT3
IOSTRB
A15
U2
U1
R/W
IS
Figure 31. ADS1606—TMS320C5400 Interface
Connection
RD
Code Composer Studio, available from TI, provides
support for interfacing TI DSPs through a collection of
data converter plugins. Check the TI website, located
at www.ti.com/sc/dcplug−in, for the latest information
on ADS1605/6 support.
Figure 30. ADS1605—TMS320C5400 Interface
Connection
29
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢤ
ꢉꢃ ꢠꢡ ꢢ ꢣ ꢢ
www.ti.com
SBAS274H − MARCH 2003 − REVISED MAY 2007
Revision History
DATE
REV
PAGE
SECTION
Readback Considerations Added last three sentences.
DESCRIPTION
5/15/07
H
24
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
30
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
ADS1605IPAPR
ADS1605IPAPRG4
ADS1605IPAPT
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
HTQFP
HTQFP
HTQFP
HTQFP
HTQFP
HTQFP
PAP
64
64
64
64
64
64
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
ADS1605I
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PAP
PAP
PAP
PAP
PAP
1000
250
250
250
250
Green (RoHS
& no Sb/Br)
ADS1605I
ADS1605I
ADS1605I
ADS1606I
ADS1606I
Green (RoHS
& no Sb/Br)
ADS1605IPAPTG4
ADS1606IPAPT
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
ADS1606IPAPTG4
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
ADS1605IPAPR
ADS1605IPAPT
ADS1606IPAPT
HTQFP
HTQFP
HTQFP
PAP
PAP
PAP
64
64
64
1000
250
330.0
330.0
330.0
24.4
24.4
24.4
13.0
13.0
13.0
13.0
13.0
13.0
1.5
1.5
1.5
16.0
16.0
16.0
24.0
24.0
24.0
Q2
Q2
Q2
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
ADS1605IPAPR
ADS1605IPAPT
ADS1606IPAPT
HTQFP
HTQFP
HTQFP
PAP
PAP
PAP
64
64
64
1000
250
367.0
367.0
367.0
367.0
367.0
367.0
45.0
45.0
45.0
250
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明