ADS5422Y [TI]
14-Bit, 62MSPS Sampling ANALOG-TO-DIGITAL CONVERTER; 14位, 62MSPS采样模拟数字转换器型号: | ADS5422Y |
厂家: | TEXAS INSTRUMENTS |
描述: | 14-Bit, 62MSPS Sampling ANALOG-TO-DIGITAL CONVERTER |
文件: | 总19页 (文件大小:394K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ADS5422
ADS5422
SBAS250C – MARCH 2002 – REVISED MARCH 2004
14-Bit, 62MSPS Sampling
ANALOG-TO-DIGITAL CONVERTER
FEATURES
DESCRIPTION
● HIGH DYNAMIC RANGE:
High SFDR: 85dB at 10MHz fIN
High SNR: 72dB at 10MHz fIN
The ADS5422 is a high-dynamic range, 14-bit, 62MSPS,
pipelined Analog-to-Digital Converter (ADC). It includes a
high-bandwidth linear track-and-hold amplifier that gives good
spurious performance up to the Nyquist rate. The clock input
can accept a low-level differential sine wave or square wave
signal down to 0.5Vp-p, further improving the Signal-to-Noise
Ratio (SNR) performance.
● PREMIUM TRACK-AND-HOLD:
Differential Inputs
Selectable Full-Scale Input Range
● FLEXIBLE CLOCKING:
Differential or Single-Ended
Accepts Sine or Square Wave Clocking Down to
0.5Vp-p
The ADS5422 has a 4Vp-p differential input range
(2Vp-p • 2 inputs) for optimum Spurious-Free Dynamic
Range (SFDR). The differential operation gives the lowest
even-order harmonic components. A lower input voltage can
also be selected using the internal references, further optimizing
SFDR.
Variable Threshold Level
APPLICATIONS
The ADS5422 is available in an LQFP-64 package.
● COMMUNICATIONS RECEIVERS
● TEST INSTRUMENTATION
● CCD IMAGING
+VS
DV
CLK
ADS5422
Timing Circuitry
CLK
14-Bit
Pipelined
ADC
2Vp-p
2Vp-p
IN
IN
D0
Error
Correction
Logic
3-State
Outputs
•
•
•
T&H
D13
Core
CM
(+2.5V)
Reference Ladder
and Driver
Reference and
Mode Select
REFT
VREF SEL1 SEL2
REFB
PD
OE VDRV
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2002-2004, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
PACKAGE/ORDERING INFORMATION(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESIGNATOR
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
PACKAGE-LEAD
ADS5422
LQFP-64
PM
–40°C to +85°C
ADS5422Y
ADS5422Y/250
ADS5422Y/1K5
Tape and Reel, 250
Tape and Reel, 1500
"
"
"
"
"
NOTE: (1) For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet..
ABSOLUTE MAXIMUM RATINGS(1)
+VSA, +VSD, VDRV ............................................................................... +6V
ELECTROSTATIC
Analog Input .......................................................... (–0.3V) to (+VS + 0.3V)
Logic Input ............................................................ (–0.3V) to (+VS + 0.3V)
Case Temperature ......................................................................... +100°C
Junction Temperature .................................................................... +150°C
Storage Temperature ..................................................................... +150°C
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instru-
ments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
EVALUATION BOARD
PRODUCT
DESCRIPTION
USER’S GUIDE
ADS5422EVM
Populated Evaluation Board
SBAU084
TIMING DIAGRAM
N + 9
N + 10
N + 8
N + 2
N + 1
N + 4
N + 3
Analog In
N
N + 7
N + 5
N + 6
tL
tH
tA
tCONV
Clock
10 Clock Cycles
N – 6 N – 5
t2
N
Data Out
N – 10
N – 9
N – 8
N – 7
N – 4
N – 3
N – 2
N – 1
Data Invalid
t1
Data Valid Output
tDV
SYMBOL
DESCRIPTION
MIN
TYP
MAX
1µs
UNITS
tCONV
tL
tH
tA
t1
Clock Period
Clock Pulse LOW
Clock Pulse HIGH
Aperture Delay
16.1
7.05
7.05
ns
ns
ns
ns
ns
ns
ns
tCONV/2
tCONV/2
3
Data Hold Time, CL = 0pF
New Data Delay Time, CL = 15pF max
Data Valid Output, CL = 15pF
3.9
t2
tDV
7.7
3
REFERENCE AND FULL-SCALE RANGE SELECT
DESIRED FULL-SCALE RANGE
SEL1
SEL2
INTERNAL VREF
4Vp-p
3Vp-p
2Vp-p
GND
GND
VREF
GND
+VSA
GND
2V
1.5V
1V
NOTE: For external reference operation, tie VREF to +VSA. The full-scale range will be 2x the reference value. For example, selecting a 2V external reference
will set the full-scale values of 1.5V to 3.5V for both IN and IN inputs.
ADS5422
2
SBAS250C
www.ti.com
ELECTRICAL CHARACTERISTICS
TA = specified temperature range, typical at +25°C, +VSA = +VSD = +5V, differential input range = 1.5V to 3.5V, sampling rate = 62MHz, internal reference, VDRV = +3V,
and –1dBFS, unless otherwise noted.
ADS5422Y
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
RESOLUTION
14 Tested
Bits
SPECIFIED TEMPERATURE RANGE
Ambient Air
–40
+85
3.5
°C
ANALOG INPUT
Standard Differential Input Range
Common-Mode Voltage
Optional Input Ranges
Analog Input Bias Current
Analog Input Bandwidth
Input Capacitance
Full-Scale = 4Vp-p
Selectable
1.5
V
V
V
µA
MHz
pF
2.5
2Vp-p or 3Vp-p
1
500
9
CONVERSION CHARACTERISTICS
Sample Rate
Data Latency
1M
62M
Samples/sec
Clk Cyc
10
DYNAMIC CHARACTERISTICS
Differential Linearity Error (largest code error)
f = 1MHz
f = 10MHz
No Missing Codes
Integral Nonlinearity Error, f = 10MHz
Spurious-Free Dynamic Range(1)
f = 1MHz
f = 10MHz
f = 30MHz
±0.65
±0.65
Tested
±4.0
LSB
LSB
±1.0
LSB
85
85
81
dBFS(2)
dBFS
dBFS
78
2-Tone Intermodulation Distortion(3)
f = 14.5MHz and 15.5MHz (–7dB each tone)
Signal-to-Noise Ratio (SNR)
f = 1MHz
f = 10MHz
f = 30MHz
–90
dBc
73
72
72
dBFS
dBFS
dBFS
70
67
Signal-to-(Noise + Distortion) (SINAD)
f = 1MHz
72
71
71
11.7
0.6
3
dBFS
dBFS
dBFS
Bits
LSB rms
ns
f = 10MHz
f = 30MHz
Effective Number of Bits(4)
Output Noise
f = 1MHz
IN and IN tied to CM
Aperture Delay Time
Aperture Jitter
Over-Voltage Recovery Time
Full-Scale Step Acquisition Time
1.0
5.0
5
ps rms
ns
ns
DIGITAL INPUTS
+3V/+5V Logic Compatible CMOS
Logic Family (other than clock inputs)
Clock Input
Rising Edge of Convert Clock
+0.5
+VSD
Vp-p
Logic Family (Other Clock Inputs)
HIGH Level Input Current(5) (VIN = 5V)
LOW Level Input Current (VIN = 0V)
HIGH Level Input Voltage
LOW Level Input Voltage
Input Capacitance
100
10
µA
µA
V
V
pF
+2.0
+1.0
5
(6)
+3V/+5V Logic Compatible CMOS
Straight Offset Binary
DIGITAL OUTPUTS
Logic Family
Logic Coding
Low Output Voltage (IOL = 50µA to 0.5mA)
High Output Voltage (IOH = 50µA to 0.5mA)
Low Output Voltage (IOL = 50µA to 1.6mA)
High Output Voltage (IOH = 50µA to 1.6mA)
3-State Enable Time
VDRV = 3V
VDRV = 5V
+0.2
V
V
V
+2.5
+2.5
+0.2
V
OE = H to L
OE = L to H
20
2
5
40
10
ns
ns
pF
3-State Disable Time
Output Capacitance
ACCURACY
Zero Error (Referred to –FS)
Zero Error Drift (Referred to –FS)
Gain Error(7)
at +25°C
at +25°C
±0.5
15
±0.2
35
68
±1.0
±1.0
%FS
ppm/°C
%FS
ppm/°C
dB
Gain Error Drift(7)
Power-Supply Rejection of Gain
∆VS = ±5%
Internal Reference Tolerance (VREFT, VREFB
External Reference Voltage Range
Reference Input Resistance
)
REFT, REFB Deviation from Ideal
±10
2
1.0
±50
2.025
mV
V
kΩ
0.9
POWER-SUPPLY REQUIREMENTS
Supply Voltage: +VSA, +VSD
Supply Current: +IS
Output Driver Supply Current (VDRV = 3V)
Power Dissipation: VDRV = 3V
Power Down
Operating, fIN = 10MHz
Operating, fIN = 10MHz
+4.75
+5.0
240
12
1.2
40
+5.25
1.4
V
mA
mA
W
Operating
mW
Thermal Resistance, θJA
LQFP-64
48
°C/W
NOTES: (1) Spurious-Free Dynamic Range refers to the magnitude of the largest harmonic. (2) dBFS means dB relative to full scale. (3) 2-tone intermodulation
distortion is referred to the largest fundamental tone. This number will be 6dB higher if it is referred to the magnitude of the 2-tone fundamental envelope.
(4) Effective Number of Bits (ENOB) is defined by (SINAD – 1.76)/6.02. (5) A 50kΩ pull-down resistor is inserted internally. (6) Recommended maximum capacitance
loading, 15pF. (7) Includes internal reference.
ADS5422
SBAS250C
3
www.ti.com
PIN CONFIGURATION
Top View
LQFP
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
+VSA
+VSA
+VSD
+VSD
+VSD
+VSD
GND
GND
CLK
1
2
3
4
5
6
7
8
9
48 GND
47 GND
46 VREF
45 SEL1
44 SEL2
43 GND
42 GND
41 BTC
ADS5422Y
40 PD
CLK 10
GND 11
39 OE
38 GNDRV
37 GNDRV
36 GNDRV
35 VDRV
34 VDRV
33 VDRV
GND 12
GNDRV 13
GNDRV 14
DNC 15
DV 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PIN DESCRIPTIONS
PIN
I/O
DESIGNATOR
DESCRIPTION
Analog Supply Voltage
PIN
I/O
DESIGNATOR
DESCRIPTION
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
VDRV
VDRV
VDRV
GNDRV
GNDRV
GNDRV
OE
Output Driver Supply Voltage
Output Driver Supply Voltage
Output Driver Supply Voltage
Ground
1
2
3
4
5
6
7
8
+VSA
+VSA
+VSD
+VSD
+VSD
+VSD
GND
GND
CLK
CLK
GND
GND
GNDRV
GNDRV
DNC
DV
B1
B2
B3
B4
B5
B6
B7
B8
Analog Supply Voltage
Digital Supply Voltage
Digital Supply Voltage
Digital Supply Voltage
Digital Supply Voltage
Ground
Ground
Clock Input
Complementary Clock Input
Ground
Ground
Ground
Ground
Output Enable: HI = High Impedance
Power Down: HI = Power Down; LO = Normal
HI = Binary Two’s Complement
Ground
PD
BTC
9
I
I
GND
GND
SEL2
SEL1
VREF
GND
GND
GND
REFB
CM
REFT
GND
GND
GND
GND
IN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Ground
Reference Select 2: See Table I
Reference Select 1: See Table I
Internal Reference Voltage
Ground
Ground
Ground
Do Not Connect
Data Valid Pulse: HI = Data Valid
Data Bit 1 (D13) (MSB)
Data Bit 2 (D12)
Data Bit 3 (D11)
Data Bit 4 (D10)
Data Bit 5 (D9)
Data Bit 6 (D8)
Data Bit 7 (D7)
Data Bit 8 (D6)
Data Bit 9 (D5)
Data Bit 10 (D4)
Data Bit 11 (D3)
Data Bit 12 (D2)
Data Bit 13 (D1)
Data Bit 14 (D0) (LSB)
No Internal Connection
No Internal Connection
Ground
Ground
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Bottom Reference Voltage Bypass
Common-Mode Voltage (Midscale)
Top Reference Voltage Bypass
Ground
Ground
Ground
Ground
I
I
Complementary Analog Input
Ground
Analog Input
B9
GND
IN
B10
B11
B12
B13
B14
NC
GND
REFBY
GND
+VSA
+VSA
Ground
Reference Bypass
Ground
Analog Supply Voltage
Analog Supply Voltage
NC
ADS5422
4
SBAS250C
www.ti.com
TYPICAL CHARACTERISTICS
TA = 25°C, +VSA = +VSD = +5V, differential input range = 1.5V to 3.5V each input (4Vp-p), sampling rate = 62MSPS, internal reference, and VDRV = 3V, unless otherwise
noted.
SPECTRAL PERFORMANCE
SPECTRAL PERFORMANCE
0
–20
0
–20
–40
–40
–60
–60
–80
–80
–100
–120
–100
–120
0
5
10
15
20
25
30
0
5
10
15
20
25
30
Frequency (MHz)
Frequency (MHz)
SPECTRAL PERFORMANCE
SPECTRAL PERFORMANCE
0
–20
0
–20
–40
–40
–60
–60
–80
–80
–100
–120
–100
–120
0
5
10
15
20
25
30
0
5
10
15
20
25
30
Frequency (MHz)
Frequency (MHz)
SPECTRAL PERFORMANCE
SPECTRAL PERFORMANCE (2Vp-p)
0
–20
0
–20
–40
–40
–60
–60
–80
–80
–100
–120
–100
–120
0
5
10
15
20
25
30
0
5
10
15
20
25
30
Frequency (MHz)
Frequency (MHz)
ADS5422
SBAS250C
5
www.ti.com
TYPICAL CHARACTERISTICS (Cont.)
TA = 25°C, +VSA = +VSD = +5V, differential input range = 1.5V to 3.5V each input (4Vp-p), sampling rate = 62MSPS, internal reference, and VDRV = 3V, unless otherwise
noted.
SPECTRAL PERFORMANCE (3Vp-p)
fIN = 10MHz, –3dBFS
2-TONE INTERMODULATION DISTORTION
0
–20
0
–20
f1 = (–7dBc) = 14.5MHz
f2 = (–7dBc) = 15.5MHz
SFDR = 89.7dB
SFDR = 85.1dBFS
SNR = 71.9dBFS
–40
–40
–60
–60
–80
–80
–100
–120
–100
–120
0
5
10
15
20
25
30 31
0
5
10
15
20
25
30
Frequency (MHz)
Frequency (MHz)
DIFFERENTIAL LINEARITY ERROR
fIN = 1MHz
INTEGRAL LINEARITY ERROR
1
0.8
5
4
0.6
3
0.4
2
0.2
1
0
0
–0.2
–0.4
–0.6
–0.8
–1
–1
–2
–3
–4
–5
0
2000 4000 6000 8000 10000 12000 14000 16000
Code
0
2000 4000 6000 8000 10000 12000 14000 16000
Code
SFDR AND SNR vs INPUT FREQUENCY
SFDR
SWEPT POWER (SFDR)
100
90
80
70
60
50
40
100
90
80
70
60
50
40
30
20
10
0
fIN = 10MHz
SNR
1.0
10
100
–60
–50
–40
–30
–20
–10
0
Frequency (MHz)
Input Amplitude (dBFS)
ADS5422
6
SBAS250C
www.ti.com
TYPICAL CHARACTERISTICS (Cont.)
TA = 25°C, +VSA = +VSD = +5V, differential input range = 1.5V to 3.5V each input (4Vp-p), sampling rate = 62MSPS, internal reference, and VDRV = 3V, unless otherwise
noted.
OUTPUT NOISE HISTOGRAM
(DC Common-Mode Input)
SWEPT POWER (SNR)
dBFS
600000
500000
400000
300000
200000
100000
0
90
80
70
60
50
40
30
20
10
0
fIN = 10MHz
dBc
N – 3 N – 2 N – 1
N
N + 1 N + 2 N + 3
–60
–50
–40
–30
–20
–10
0
Input Amplitude (dBFS)
nonlinearity of RON. For ease of use, the ADS5422 incorpo-
rates a selectable voltage reference, a versatile clock input,
and a logic output driver designed to interface to 3V or 5V
logic.
APPLICATION INFORMATION
THEORY OF OPERATION
The ADS5422 is a high-speed, high-performance, CMOS
ADC built with a fully differential pipeline architecture. Each
stage contains a low-resolution quantizer and digital error
correction logic ensuring good differential linearity. The con-
version process is initiated by a rising edge of the external
convert clock. Once the signal is captured by the input track-
and-hold amplifier, the bits are sequentially encoded starting
with the Most Significant Bit (MSB). This process results in a
data latency of 10 clock cycles after which the output data is
available as a 14-bit parallel word either coded in a Straight
Offset Binary or Binary Two’s Complement format.
S5
ADS5422
S3
VBIAS
S1
S2
CIN
CIN
IN
IN
T&H
The analog input of the ADS5422 consists of a differential
track-and-hold circuit, as shown in Figure 1. The differential
topology produces a high level of AC performance at high
sampling rates. It also results in a very high usable input
bandwidth—especially important for Intermediate Frequency
S4
VBIAS
S6
Tracking Phase: S1, S2, S3, S4 closed; S5, S6 open
Hold Phase: S1, S2, S3, S4 open; S5, S6 closed
(IF) or undersampling applications. Both inputs (IN, IN
)
require external biasing up to a common-mode voltage that
is typically at the mid-supply level (+VS/2). This is because
the on-resistance of the CMOS switches is lowest at this
voltage, minimizing the effects of the signal-dependent,
FIGURE 1. Simplified Circuit of Input Track-and-Hold Amplifier.
ADS5422
SBAS250C
7
www.ti.com
be considered for achieving a combination of both low-noise
and distortion performance. Here, the SNR number is typically
3dB down compared to the 4Vp-p range, whereas an improve-
ment in the distortion performance of the driver amplifier may
be realized due to the reduced output power level required.
The third option, 2Vp-p full-scale range, can be considered
mainly for applications requiring DC-coupling and/or single-
supply operation of the driver and the converter.
ANALOG INPUTS
TYPES OF APPLICATIONS
The analog input of the ADS5422 can be configured in
various ways and driven with different circuits, depending on
the application and the desired level of performance. Offering
an extremely high dynamic range at high input frequencies,
the ADS5422 is particularly well-suited for communication
systems that digitize wideband signals. Features on the
ADS5422, like the input range selector, or the option of an
external reference, provide the needed flexibility to accom-
modate a wide range of applications. In any case, the analog
interface/driver requirements should be carefully examined
before selecting the appropriate circuit configuration. The
circuit definition should include considerations on the input
frequency spectrum and amplitude, as well as the available
power supplies.
INPUT BIASING (VCM
)
The ADS5422 operates from a single +5V supply, and
requires each of the analog inputs to be externally biased to
a common-mode voltage of typically +2.5V. This allows a
symmetrical signal swing while maintaining sufficient head-
room to either supply rail. Communication systems are usu-
ally AC-coupled in between signal processing stages, mak-
ing it convenient to set individual common-mode voltages
and allow optimizing the DC operating point for each stage.
Other applications, such as imaging, process mainly unipolar
or DC-restored signals. In this case, the common-mode
voltage can be shifted such that the full input range of the
converter is utilized.
DIFFERENTIAL INPUTS
The ADS5422 input structure is designed to accept the
applied signal in differential format. Differential operation of
the ADS5422 requires an input signal that consists of an in-
phase and a 180° out-of-phase component simultaneously
applied to the inputs (IN, IN). Differential signals offer a
number of advantages, which in many applications will be
instrumental in achieving the best harmonic performance of
the ADS5422:
It should be noted that the CM pin is not internally buffered,
but ties directly to the reference ladder; therefore, it is
recommended to keep loading of this pin to a minimum
(< 100µA) to avoid an increase in the nonlinearity of the
converter. Additionally, the DC voltage at the CM pin is not
precisely +2.5V, but is subject to the tolerance of the top and
bottom references, as well as the resistor ladder. Further-
more, the common-mode voltage typically declines with an
increase in sampling frequency. This, however, does not
affect the performance.
•
The signal amplitude is half of that required for the single-
ended operation and is, therefore, less demanding to
achieve while maintaining good linearity performance from
the signal source.
•
The reduced signal swing allows for more headroom of
the interface circuitry and, therefore, a wider selection of
the best suitable driver amplifier.
INPUT IMPEDANCE
The input of the ADS5422 is capacitive, and the driving source
needs to provide the slew current to charge or discharge the
input sampling capacitor while the track-and-hold amplifier is
in track mode (see Figure 1). This effectively results in a
dynamic input impedance that is a function of the sampling
frequency. Figure 2 depicts the differential input impedance of
the ADS5422 as a function of the input frequency.
•
•
Even-order harmonics are minimized.
Improves the noise immunity based on the common-
mode input rejection of the converter.
Both inputs are identical in terms of their impedance and
performance with the exception that by applying the signal to
the complementary input (IN) instead of the IN input will invert
the orientation of the input signal relative to the output code.
INPUT FULL-SCALE RANGE VERSUS PERFORMANCE
1000
100
10
Employing dual-supply amplifiers and AC-coupling will usually
yield the best results. DC-coupling and/or single-supply ampli-
fiers impose additional design constraints due to their head-
room requirements, especially when selecting the
4Vp-p input range. The full-scale input range of the ADS5422
is defined either by the settings of the reference select pins
(SEL1, SEL2) or by an external reference voltage
(see Table I). By choosing between the different signal input
ranges, trade-offs can be made between noise and distortion
performance. For maximizing the SNR—important for time-
domain applications—the 4Vp-p range may be selected. This
range may also be used with low-level (–6dBFS to –40dBFS)
but high-frequency inputs (multi-tone). The 3Vp-p range may
1
0.1
0.01
0.1
1
10
100
1000
fIN (MHz)
FIGURE 2. Differential Input Impedance vs Input Frequency.
ADS5422
8
SBAS250C
www.ti.com
For applications that use op amps to drive the ADC, it is
recommended that a series resistor be added between the
amplifier output and the converter inputs. This will isolate the
capacitive input of the converter from the driving source and
avoid gain peaking, or instability; furthermore, it will create a 1st-
order, low-pass filter in conjunction with the specified input
capacitance of the ADS5422. Its cutoff frequency can be
adjusted further by adding an external shunt capacitor from
each signal input to ground. The optimum values of this RC
network, however, depend on a variety of factors including the
ADS5422 sampling rate, the selected op amp, the interface
configuration, and the particular application (time domain versus
frequency domain). Generally, increasing the size of the series
resistor and/or capacitor will improve the SNR; however, de-
pending on the signal source, large resistor values can be
detrimental to the harmonic distortion performance. In any case,
the use of the RC network is optional but optimizing the values
to adapt to the specific application is encouraged.
datasheet located at the Texas Instruments web site
(www.ti.com). In general, differential amplifiers provide for a
high-performance driver solution for baseband applications,
and different differential amplifier models can be selected
depending on the system requirements.
TRANSFORMER-COUPLED INTERFACE CIRCUITS
If the application allows for AC-coupling but requires a signal
conversion from a single-ended source to drive the ADS5422
differentially, using a transformer offers a number of advan-
tages. As a passive component, it does not add to the total
noise, and by using a step-up transformer, further signal
amplification can be realized. As a result, the signal swing of
the amplifier driving the transformer can be reduced, leading
to an increased headroom for the amplifier and improved
distortion performance.
A transformer interface solution is given in Figure 4. The input
signal is assumed to be an IF and bandpass filtered prior to the
IF amplifier. Dedicated IF amplifiers are commonly fixed-gain
blocks and feature a very high bandwidth, a low-noise figure,
and a high intercept point, but at the expense of high quiescent
currents, which are often around 100mA. The IF amplifier may
be AC-coupled, or directly connected to the primary side of the
transformer. A variety of miniature RF transformers are readily
available from different manufacturers, (e.g., Mini-Circuits,
Coilcraft, or Trak). For selection, it is important to carefully
examine the application requirements and determine the cor-
rect model, the desired impedance ratio, and frequency char-
acteristics. Furthermore, the appropriate model must support
the targeted distortion level and should not exhibit any core
saturation at full-scale voltage levels. The transformer center
tap can be directly tied to the CM pin of the converter because
it does not appreciably load the ADC reference (see Figure 4).
The value of termination resistor RT must be chosen to satisfy
the termination requirements of the source impedance (RS). It
can be calculated using the equation RT = n2 • RS to ensure
proper impedance matching.
ANALOG INPUT DRIVER CONFIGURATIONS
The following section provides some principal circuit sugges-
tions on how to interface the analog input signal to the
ADS5422. Applications that have a requirement for DC-
coupling a new differential amplifier, such as the THS4502,
can be used to drive the ADS5422, as shown in Figure 3. The
THS4502 amplifier allows a single-ended to differential con-
version to be performed easily, which reduces component
cost. In addition, the VCM pin on the THS4502 can be directly
tied to the common-mode pin (CM) of the ADS5422 in order
to set up the necessary bias voltage for the converter inputs.
As shown in Figure 3, the THS4502 is configured for unity
gain. If required, higher gain can easily be configured, and a
low-pass filter can be created by adding small capacitors
(e.g., 10pF) in parallel to the feedback resistors. Due to the
THS4502 driving a capacitive load, small series resistors in
the output ensure stable operation. Further details of this and
other functions of the THS4502 may be found in its product
10pF(1)
+5V
+5V
392Ω
RS
392Ω
25Ω
IN
THS4502
56.2Ω
VCM
ADS5422
22pF
25Ω
IN
0.1µF
392Ω
CM
412Ω
10pF(1)
–5V
NOTES: Supply bypassing not shown. (1) Optional.
FIGURE 3. Using the THS4502 Differential Amplifier (Gain = 1) to Drive the ADS5422 in a DC-Coupled Configuration.
ADS5422
SBAS250C
9
www.ti.com
+5V
XFR
1:n
RS
RIN
RIN
Optional
Bandpass
Filter
IF
VIN (IF)
IN
IN
Amplifier
CIN
ADS5422
RT
CM
NOTE: Supply bypassing not shown.
+
2.2µF
0.1µF
FIGURE 4. Driving the ADS5422 with a Low-Distortion IF Amplifier and a Transformer Suited for IF Sampling Applications.
TRANSFORMER-COUPLED, SINGLE-ENDED-TO-
DIFFERENTIAL CONFIGURATION
The circuit also shows the use of an additional RC low-pass
filter placed in series with each converter input. This optional
filter can be used to set a defined corner frequency and
attenuate some of the wideband noise. The actual compo-
nent values would need to be tuned for individual application
requirements. As a guideline, resistor values are typically in
the range of 10Ω to 50Ω, and capacitors in the range of 10pF
to 100pF. In any case, the RIN and CIN values should have
a low tolerance. This will ensure that the ADS5422 sees
closely matched source impedances.
For applications in which the input frequency is limited to
approximately 10MHz (e.g., baseband), a high-speed opera-
tional amplifier may be used. The OPA847 is configured for
the noninverting mode; this amplifies the single-ended input
signal and drives the primary of a RF transformer, as shown
in Figure 5. To maintain the very low distortion performance
of the OPA847, it may be advantageous to set the full-scale
input range of the ADS5422 to 3Vp-p or 2Vp-p (refer to the
Reference section for details on selecting the converter’s full-
scale range).
+5V –5V
+5V
RG
RS
RIN
0.1µF
VIN
1:n
OPA847
IN
CIN
RT
RIN
ADS5422
R1
IN
CM
VCM ≈ +2.5V
R2
+
0.1µF
2.2µF
FIGURE 5. Converting a Single-Ended Input Signal into a Differential Signal Using an RF Transformer.
ADS5422
10
SBAS250C
www.ti.com
AC-COUPLED, DIFFERENTIAL INTERFACE
WITH GAIN
The measured 2-tone, 3rd-order distortion for the amplifier
portion of the circuit of Figure 6 is shown in Figure 7. The
upper curve is for a total 2-tone envelope of 4Vp-p, requiring
two tones, each 2Vp-p across the OPA847 outputs. The
lower curve is for a 2Vp-p envelope resulting in a 1Vp-p
amplitude per tone. The basic measurement dynamic range
for the two close-in spurious tones is approximately 85dBc.
The 4Vp-p test does not show measurable 3rd-order spuri-
ous until 25MHz, while the 2Vp-p is unmeasurable up to
40MHz center frequency. 2-tone, 2nd-order intermodulation
distortion was unmeasurable for this circuit.
The interface circuit example presented in Figure 6 employs
two OPA847s (decompensated voltage-feedback op amps),
optimized for gains of 12V/V or higher. Implementing a new
compensation technique allows the OPA847s to operate with
a reduced signal gain of 8.5V/V, while maintaining the high
loop gain and the associated excellent distortion perfor-
mance offered by the decompensated architecture. For a
detailed discussion on this circuit and the compensation
scheme, refer to the OPA847 data sheet (SBOS251) avail-
able at www.ti.com. Input transformer, T1, converts the
single-ended input signal to a differential signal required at
the inverting inputs of the amplifier, which are tuned to
provide a 50Ω impedance match to an assumed 50Ω source.
To achieve the 50Ω input match at the primary of the 1:2
transformer, the secondary must see a 200Ω load imped-
ance. Both amplifiers are configured for the inverting mode
resulting in close gain and phase matching of the differential
signal. This technique, along with a highly symmetrical lay-
out, is instrumental in achieving a substantial reduction of the
2nd-harmonic, while retaining excellent 3rd-order perfor-
mance. A common-mode voltage, VCM, is applied to the
noninverting inputs of the OPA847. Additional series 20Ω
resistors isolate the output of the op amps from the capaci-
tive load presented by the 40pF capacitors and the input
capacitance of the ADS5422. This 20Ω/47pF combination
sets a pole at approximately 85MHz and rolls off some of the
wideband noise resulting in a reduction of the noise floor.
–60
–65
4Vp-p
–70
–75
2Vp-p
–80
–85
0
5
10
15 20
25
30 35
40
45 50
Center Frequency (MHz)
FIGURE 7. Measured 2-Tone, 3rd-Order Distortion for a
Differential ADC Driver.
+5V
VCM
20Ω
OPA847
100Ω
–5V
+5V
1.7pF
T1
39pF
39pF
850Ω
50Ω Source
1:2
IN
ADS5422
47pF
< 6dB
Noise
Figure
850Ω
IN
1.7pF
CM
VCM
+5V
100Ω
0.1µF
20Ω
OPA847
VCM
–5V
FIGURE 6. High Dynamic Range Interface Circuit with the OPA847 Set for a Gain of +8.5V/V.
ADS5422
SBAS250C
11
www.ti.com
The top and bottom reference outputs may be used to
provide up to 1mA of current (sink or source) to external
circuits. Degradation of the differential linearity (DNL) and,
consequently, the dynamic performance, of the ADS5422
can occur if this limit is exceeded.
REFERENCE
REFERENCE OPERATION
Integrated into the ADS5422 is a bandgap reference circuit
including logic that provides a +1V, +1.5V, or +2V reference
output by selecting the corresponding pin-strap configura-
tion. Table I gives a complete overview of the possible
reference options and pin configurations.
USING EXTERNAL REFERENCES
For even more design flexibility, the ADS5422 can be
operated with external references. The utilization of an
external reference voltage can be considered for applica-
tions requiring higher accuracy, improved temperature sta-
bility, or a continuous adjustment of the converter full-scale
range. Especially in multichannel applications, the use of a
common external reference offers the benefit of improving
the gain matching between converters. Selection between
internal or external reference operation is controlled through
the VREF pin. The internal reference will become disabled if
the voltage applied to the VREF pin exceeds +3.5VDC. Once
selected, the ADS5422 requires two reference voltages—a
top reference voltage applied to the REFT pin and a bottom
reference voltage applied to the REFB pin (see Table I). As
illustrated in Figure 9, a micropower reference (REF1004)
and a dual, single-supply amplifier (OPA2234) can be used
to generate a precision external reference. Note that the
function of the range select pins, SEL1 and SEL2, are
disabled while the converter is operating in external refer-
ence mode.
Figure 8 shows the basic model of the internal reference
circuit. The functional blocks are a 1V bandgap voltage
reference, a selectable gain amplifier, the drivers for the top
and bottom reference (REFT, REFB), and the resistive refer-
ence ladder. The ladder resistance measures approximately
1kΩ between the REFT and REFB pins. The ladder is split
into two equal segments establishing a common-mode volt-
age at the ladder midpoint, labeled CM. The ADS5422
requires solid bypassing for all reference pins to keep the
effects of clock feedthrough to a minimum and to achieve the
specified level of performance. Figure 8 shows the recom-
mended decoupling scheme. All 0.1µF capacitors should be
located as close to the pins as possible. In addition, pins
REFT, CM, and REFB should be decoupled with tantalum
surface-mount capacitors (2.2µF or 4.7µF).
When operating the ADS5422 with the internal reference, the
effective full-scale input span for each of the inputs, IN and
IN, is determined by the voltage at the VREF pin, given to:
(1)
Input Span (differential, each input) = VREF = (REFT – REFB) in Vp-p
DESIRED FULL-SCALE
RANGE (FSR)
(DIFFERENTIAL)
CONNECT
SEL1 (PIN 45) TO:
CONNECT
SEL2 (PIN 44) TO:
VOLTAGE AT VREF
(PIN 46)
VOLTAGE AT REFT
(PIN 52)
VOLTAGE AT REFB
(PIN 50)
4Vp-p (+16dBm)
3Vp-p (+13dBm)
2Vp-p (+10dBm)
External Reference
GND
GND
VREF
—
GND
+VSA
GND
—
+2.0V
+1.5V
+3.5V
+3.25V
+1.5V
+1.75V
+1.0V
+3.0V
+2.0V
> +3.5V
+2.75V to +4.5V
+0.5V to +2.25V
TABLE I. Reference Pin Configurations and Corresponding Voltages on the Reference Pins.
SEL1 SEL2
45
44
Range Select
and
Gain Amplifier
Top
Reference
Driver
REFBY
0.1µF
REFT
CM
+
+
+
52
500Ω
61
0.1µF
0.1µF
0.1µF
2.2µF
2.2µF
2.2µF
+1VDC
Bandgap
Reference
51
500Ω
Bottom
Reference
Driver
REFB
50
ADS5422
46
0.1µF
VREF
FIGURE 8. Internal Reference Circuit of the ADS5422 and Recommended Bypass Scheme.
ADS5422
12
SBAS250C
www.ti.com
+5V
+5V
1/2
OPA2234
REFT
4.7kΩ
+
2.2µF
0.1µF
R3
ADS5422
R4
R1
+
REF1004
+2.5V
10µF
1/2
OPA2234
REFB
+
R2
0.1µF
2.2µF
0.1µF
FIGURE 9. Example for an External Reference Circuit Using a Dual, Single-Supply Op Amp.
DIGITALINPUTSAND OUTPUTS
CLOCK INPUT
CLK
ADS5422
TTL/CMOS
Clock Source
(3V/5V)
Unlike most ADCs, the ADS5422 contains internal clock
conditioning circuitry. This enables the converter to adapt to
a variety of application requirements and different clock
CLK
sources. With no input signal connected to either clock pin,
47nF
the threshold level is set to approximately +1.6V by the on-
chip resistive voltage divider, as shown in Figure 10. The
parallel combination of R1 || R2 and R3 || R4 sets the input
FIGURE 11. Single-Ended TTL/CMOS Clock Source.
impedance of the clock inputs (CLK, CLK) to approximately
2.7kΩ single-ended, or 5.5kΩ differentially. The associated
ground referenced input capacitance is approximately 5pF
for each input. If a logic voltage other than the nominal +1.6V
is desired, the clock inputs can be externally driven to
establish an alternate threshold voltage.
Applying a single-ended clock signal will provide satisfactory
results in many applications. However, unbalanced high-speed
logic signals can introduce a high amount of disturbances,
such as ringing or ground bouncing. In addition, a high
amplitude may cause the clock signal to have unsymmetrical
rise-and-fall times, potentially affecting the converter distortion
performance. Proper termination practice and a clean PC
board layout will help to keep those effects to a minimum.
+5V
ADS5422
To take full advantage of the excellent distortion performance of
the ADS5422, it is recommended to drive the clock inputs
differentially. A differential clock improves the digital feedthrough
immunity and minimizes the effect of modulation between the
signal and the clock. Figure 12 illustrates a simple method of
converting a square wave clock from single-ended to differential
using an RF transformer. Small surface-mount transformers are
readily available from several manufacturers (e.g., model ADT1-
1 by Mini-Circuits). A capacitor in series with the primary side
can be inserted to block any DC voltage present in the signal.
The secondary side connects directly to the two clock inputs of
the converter because the clock inputs are self-biased.
R1
8.5kΩ
R3
8.5kΩ
CLK
CLK
R2
4kΩ
R4
4kΩ
FIGURE 10. The Differential Clock Inputs are Internally Biased.
The ADS5422 can be interfaced to standard TTL or CMOS
logic and accepts 3V or 5V compliant logic levels. In this
case, the clock signal should be applied to the CLK input,
while the complementary clock input (CLK) should be by-
passed to ground by a low-inductance ceramic chip capaci-
tor, as shown in Figure 11. Depending on the quality of the
signal, inserting a series, damping resistor may be beneficial
to reduce ringing. When digitizing at high sampling rates the
clock should have a 50% duty cycle (tH = tL) to maintain good
distortion performance.
XFR
1:1
RS
0.1µF
Square Wave
or Sine Wave
Clock Source
CLK
ADS5422
RT
CLK
FIGURE 12. Connecting a Ground-Referenced Clock Source
to the ADS5422 Using an RF Transformer.
ADS5422
SBAS250C
13
www.ti.com
The clock inputs of the ADS5422 can be connected in a
number of ways. However, the best performance is obtained
when the clock input pins are driven differentially. Operating in
this mode, the clock inputs accommodate signal swings rang-
ing from 2.5Vp-p down to 0.5Vp-p differentially. This allows
direct interfacing of clock sources such as voltage-controlled
crystal oscillators (VCXO) to the ADS5422. The advantage
here is the elimination of external logic, usually necessary to
convert the clock signal into a suitable logic (TTL or CMOS)
signal that otherwise would create an additional source of
jitter. In any case, a very low-jitter clock is fundamental to
preserving the excellent AC performance of the ADS5422.
The converter itself is specified for a low jitter, characterizing
the outstanding capability of the internal clock and track-and-
hold circuitry. Generally, as the input frequency increases, the
clock jitter becomes more dominant for maintaining a good
signal-to-noise ratio. This is particularly critical in IF sampling
applications where the sampling frequency is lower than input
frequency (undersampling). The following equation can be
used to calculate the achievable SNR for a given input
frequency and clock jitter (tJA in ps rms):
MINIMUM SAMPLING RATE
The pipeline architecture of the ADS5422 uses a switched-
capacitor technique in its internal track-and-hold stages. With
each clock cycle, charges representing the captured signal
level are moved within the ADC pipeline core. The high
sampling speed necessitates the use of very small capacitor
values. In order to hold the droop errors low, the capacitors
require a minimum ‘refresh rate.’ To maintain accuracy of the
acquired sample charge, the sampling clock on the ADS5422
should not drop below the specified minimum of 1MHz.
DATA OUTPUT FORMAT (BTC)
The ADS5422 makes two data output formats available, either
the Straight Offset Binary (SOB) code or the Binary Two’s
Complement (BTC) code. The selection of the output coding
is controlled through the BTC pin. Applying a logic HIGH will
enable the BTC coding, while a logic LOW will enable the
Straight Offset Binary code. The BTC output format is widely
used to interface to microprocessors, for example. The two
code structures are identical, with the exception that the MSB
is inverted for the BTC format; see Table II.
1
SNR = 20 log10
If the input signal exceeds the full-scale range, the output
code will remain at all 1s or all 0s.
(2)
2π f t
(
)
IN JA
Depending on the nature of the clock source’s output imped-
ance, impedance matching might become necessary. For
this, a termination resistor, RT, may be installed, as shown in
Figure 13. To calculate the correct value for this resistor,
consider the impedance ratio of the selected transformer and
the differential clock input impedance of the ADS5422, which
is approximately 5.5kΩ.
BINARY TWO’S
COMPLEMENT
(BTC)
DIFFERENTIAL
INPUT
STRAIGHT OFFSET
BINARY (SOB)
+FS – 1LSB
(IN = +3.5V, IN = +1.5V)
11 1111 1111 1111
01 1111 1111 1111
+1/2 FS
11 0000 0000 0000
10 0000 0000 0000
01 0000 0000 0000
00 0000 0000 0000
Bipolar Zero
(IN = IN = VCM
)
Shown in Figure 13 is one preferred method for clocking the
ADS5422. Here, the single-ended clock source can be either
a square wave or a sine wave. Using the high-speed differ-
ential translator SN65LVDS100 from Texas Instruments, a
low-jitter clock can be generated to drive the clock inputs of
the ADS5422 differentially.
–1/2 FS
01 0000 0000 0000
00 0000 0000 0000
11 0000 0000 0000
10 0000 0000 0000
–FS
(IN = +1.5V, IN = +3.5V)
TABLE II. Coding Table for Differential Input Configura-
tion and 4Vp-p Full-Scale Input Range.
+5V
0.01µF
SN65LVDS100
0.01µF
Square Wave
Or Sine Wave
Clock Input
0.01µF
A
Y
CLK
(1)
ADS5422
B
RT
100Ω
0.01µF
Z
CLK
VBB
50Ω
50Ω
0.01µF
NOTE: (1) Additional termination resistor RT may be necessary depending on the source requirements
FIGURE 13. Differential Clock Driver Using an LVDS Translator.
ADS5422
14
SBAS250C
www.ti.com
OUTPUT ENABLE (OE
)
POWER DISSIPATION
The digital outputs of the ADS5422 can be set to high
impedance (tri-state), exercising the output enable pin (OE).
For normal operation, this pin must be at a logic LOW
potential while a logic HIGH voltage disables the outputs.
Even though this function affects the output driver stage, the
threshold voltages for the OE pin do not depend on the
output driver supply (VDRV), but are fixed (see the Electrical
Characteristics Table and the Digital Inputs Sections). Oper-
ating the OE function dynamically (e.g., through high-speed
multiplexing) should be avoided as it will corrupt the conver-
sion process.
A majority of the ADS5422 total power consumption is used
for biasing, therefore, independent of the applied clock fre-
quency. Figure 14 shows the typical variation in power
consumption versus the clock speed. The current on the
VDRV supply is directly related to the capacitive loading of
the data output pins and care should be taken to minimize
such loading.
45
fIN = 10MHz
40
35
30
25
20
15
POWER DOWN (PD)
A power-down pin is provided which, when taken HIGH,
shuts down portions within the ADS5422 and reduces the
power dissipation to less than 40mW. The remaining active
blocks include the internal reference ensuring a fast reactiva-
tion time. During power-down, data in the converter pipeline
is lost and new valid data will be subject to the specified
pipeline delay. If the PD pin is not used, it should be tied to
ground or a logic LOW level.
700
720
740
760
780
800
820
840
880
Power Dissipation (mW)
OUTPUT LOADING
It is recommended to keep the capacitive loading on the data
output lines as low as possible, preferably below 15pF.
Higher capacitive loading causes larger dynamic currents as
the digital outputs are changing. For example, with a typical
output slew rate of 0.8V/ns and a total capacitive loading of
10pF (including 4pF output capacitance, 5pF input capaci-
tance of external logic buffer, and 1pF PC board parasitics),
a bit transition can cause a dynamic current of (10pF • 0.8V/
1ns = 8mA). These high current surges can feed back to the
analog portion of the ADS5422 and adversely affect the
performance. If necessary, external buffers or latches close
to the converter output pins may be used to minimize the
capacitive loading. They also provide the added benefit of
isolating the ADS5422 from any digital activities on the bus
coupling back high-frequency noise.
FIGURE 14. Power Dissipation vs Clock Frequency.
DIGITAL OUTPUT DRIVER SUPPLY (VDRV)
A dedicated supply pin, VDRV, provides power to the logic
output drivers of the ADS5422 and may be operated with a
supply voltage in the range of +3.0V to +5.0V. This can
simplify interfacing to various logic families, in particular low-
voltage CMOS. It is recommended to operate the ADS5422
with a +3.3V supply voltage on VDRV. This will lower the
power dissipation in the output stages due to the lower output
swing and reduce current glitches on the supply line that may
affect the AC performance of the converter. The analog
supply (+VSA) and digital supply (+VSD) may be tied together,
with a ferrite bead or inductor between the supply pins. Each
of the these supply pins must be bypassed separately with at
least one 0.1µF ceramic chip capacitor, forming a pi-filter, as
shown in Figure 15. The recommended operation for the
ADS5422 is +5V for the +VS pins and +3.3V on the output
driver pin (VDRV).
POWER SUPPLIES
When defining the power supplies for the ADS5422, it is highly
recommended to consider linear supplies instead of switching
types. Even with good filtering, switching supplies may radiate
noise that could interfere with any high-frequency input signal
and cause unwanted modulation products. At its full conver-
sion rate of 62MSPS, the ADS5422 typically requires 240mA
of supply current on the +5V supplies (+VS). Note that this
supply voltage should stay within a 5% tolerance.
The configuration of the supplies requires that a specific
power-up sequence be followed for the ADS5422. Analog
voltage must be applied to the analog supply pin (+VSA
before applying a voltage to the driver supply (VDRV) or
before bringing both the digital supply (+VSD) and VDRV
simultaneously. Powering up +VSD and VDRV prior to +VSA
will cause a large current on +VSA and result in the ADS5422
not functioning properly.
)
ADS5422
SBAS250C
15
www.ti.com
VIN
50Ω
ADT2-1
4.7µF
+
+VA
(5V)
0.1µF
0.1µF
22Ω
22Ω
4.7µF
4.7µF
+
+
22pF
0.1µF
0.1µF
0.1µF
0.1µF
10µF
+
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
1
2
3
4
5
6
7
8
9
+VSA
GND 48
GND 47
VREF 46
0.1µF
0.1µF
+VSA
+VSD
+VSD
+VSD
+VSD
GND
GND
CLK
0.01µF
0.1µF
SEL1 45
SEL2 44
GND 43
GND 42
BTC 41
+VD
(5V)
10µF
RS 0.1µF
CLKIN
ADT2-1
ADS5422
PD 40
10 CLK
OE 39
50Ω
11 GND
12 GND
13 GNDRV
14 GNDRV
15 DNC
16 DV
GNDRV 38
GNDRV 37
GNDRV 36
VDRV 35
VDRV 34
VDRV 33
0.01µF
0.1µF
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
DV
10µF
+
0.1µF
+VDR
(3.3V)
FIGURE 15. Basic Application Circuit of the ADS5422 Includes Recommended Supply and Reference Bypassing.
ADS5422
16
SBAS250C
www.ti.com
to the supply pins as possible. They are best placed directly
under the package where double-sided component mounting
is allowed. In addition, larger bipolar decoupling capacitors
(2.2µF to 10µF), effective at lower frequencies, should also be
used on the main supply pins. They can be placed on the PC
board in proximity (< 0.5") of the ADC.
LAYOUT AND DECOUPLING
CONSIDERATIONS
Proper grounding and bypassing, short lead length, and the
use of ground planes are particularly important for high-
frequency designs. Achieving optimum performance with a
fast sampling converter like the ADS5422 requires careful
attention to the PC board layout to minimize the effect of
board parasitics and optimize component placement. A mul-
tilayer board usually ensures best results and allows conve-
nient component placement.
If the analog inputs to the ADS5422 are driven differentially,
it is especially important to optimize towards a highly sym-
metrical layout. Small trace length differences may create
phase shifts compromising a good distortion performance.
For this reason, the use of two single op amps rather than
one dual amplifier enables a more symmetrical layout and a
better match of parasitic capacitances. The pin orientation of
the ADS5422 package follows a flow-through design with the
analog inputs located on one side of the package, whereas
the digital outputs are located on the opposite side of the
quad-flat package. This provides a good physical isolation
between the analog and digital connections. While designing
the layout, it is important to keep the analog signal traces
separated from any digital lines to prevent noise coupling
onto the analog portion.
The ADS5422 should be treated as an analog component
and the +VSA pins connected to a clean analog supply. This
will ensure the most consistent results, since digital supplies
often carry a high level of switching noise which could couple
into the converter and degrade the performance. As men-
tioned previously, the driver supply pins (VDRV) should also
be connected to a low-noise supply. Supplies of adjacent
digital circuits may carry substantial current transients. The
supply voltage must be thoroughly filtered before connecting
to the VDRV supply of the converter. All ground connections
on the ADS5422 are internally bonded to the metal flag
(bottom of package) that forms a large ground plane. All
ground pins should directly connect to an analog ground
plane that covers the PC board area under the converter.
Try to match trace length for the differential clock signal (if
used) to avoid mismatches in propagation delays. Single-
ended clock lines must be short and should not cross any
other signal traces.
Short-circuit traces on the digital outputs will minimize capaci-
tive loading. Trace length should be kept short to the receiving
gate (< 2") with only one CMOS gate connected to one digital
output. If possible, the digital data outputs should be buffered
(with the TI SN74AVC16244, for example). Dynamic perfor-
mance can also be improved with the insertion of series
resistors at each data output line. This sets a defined time
constant and reduces the slew rate that would otherwise flow
due to the fast edge rate. The resistor value can be chosen to
result in a time constant of 15% to 25% of the used data rate.
Due to its high sampling frequency, the ADS5422 generates
high-frequency current transients and noise (clock
feedthrough) that are fed back into the supply and reference
lines. If not sufficiently bypassed, this will add noise to the
conversion process. See Figure 15 for the recommended
supply decoupling scheme for the ADS5422. All +VS pins
should be bypassed with a combination of 10nF, 0.1µF
ceramic chip capacitors (0805, low ESR) and a 10µF tanta-
lum tank capacitor. A similar approach may be used on the
driver supply pins, VDRV. In order to minimize the lead and
trace inductance, the capacitors should be located as close
ADS5422
SBAS250C
17
www.ti.com
MECHANICAL DATA
MTQF008A – JANUARY 1995 – REVISED DECEMBER 1996
PM (S-PQFP-G64)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
M
0,08
33
48
49
32
64
17
0,13 NOM
1
16
7,50 TYP
Gage Plane
10,20
SQ
9,80
0,25
12,20
SQ
0,05 MIN
0°–7°
11,80
1,45
1,35
0,75
0,45
Seating Plane
0,08
1,60 MAX
4040152/C 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
D. May also be thermally enhanced plastic with leads connected to the die pads.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2004, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明