ADS8355IRTET [TI]
具有单端输入的 16 位 1MSPS 双通道同步采样 SAR ADC | RTE | 16 | -40 to 125;型号: | ADS8355IRTET |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有单端输入的 16 位 1MSPS 双通道同步采样 SAR ADC | RTE | 16 | -40 to 125 |
文件: | 总44页 (文件大小:2202K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
ADS8355
双路、16 位、1MSPS、同步采样,模数转换器
1 特性
3 说明
1
•
•
•
•
1MSPS 吞吐量、无延迟输出
ADS8355 是一款双路高速同步采样模数转换器
(ADC),可支持单端和伪差分模拟输入。
两个通道同步采样
支持单端和伪差分输入
出色的直流和交流性能:
该器件支持灵活的串行接口,可以在宽电源电压范围内
正常工作。通过灵活的接口可以方便地与各种主机控制
器通信。该系列器件支持两种低功耗模式,可针对给定
输出优化功耗。该器件可在完整的扩展工业温度范围
(–40°C 至 +125°C)内正常工作,并采用 16 引脚
WQFN(3mm × 3mm)封装。
–
–
16 位 NMC DNL,±1LSB INL
88dB SNR,–97dB THD
•
双路、可编程
2.5V 内部基准电压
•
•
完整的扩展工业温度范围:–40°C 至 +125°C
器件信息(1)
小型封装:
WQFN-16 (3mm × 3mm)
器件型号
ADS8355
封装
WQFN (16)
封装尺寸(标称值)
3.00mm × 3.00mm
2 应用
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
•
•
•
•
•
•
伺服驱动器位置反馈
光学模块
多功能继电器
电能质量分析仪
三相 UPS
模拟输入模块
典型方框图
AVDD
DVDD
AINP_A
AINM_A
ADC A
CS
SCLK
REFIO_A
REFA
REFB
Serial
Interface
SDI
SDO_A
REFIO_B
SDO_B
AINP_B
AINM_B
ADC B
GND
1
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。 有关适用的官方英文版本的最新信息,请访问 www.ti.com,其内容始终优先。 TI 不保证翻译的准确
性和有效性。 在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SBAS761
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
目录
7.5 Programming........................................................... 21
7.6 Register Map........................................................... 23
Application and Implementation ........................ 28
8.1 Application Information............................................ 28
8.2 Typical Application .................................................. 30
Power Supply Recommendations...................... 33
1
2
3
4
5
6
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 5
6.4 Thermal Information.................................................. 6
6.5 Electrical Characteristics........................................... 6
6.6 Timing Requirements................................................ 8
6.7 Switching Characteristics.......................................... 9
6.8 Typical Characteristics............................................ 10
Detailed Description ............................................ 14
7.1 Overview ................................................................. 14
7.2 Functional Block Diagram ....................................... 14
7.3 Feature Description................................................. 14
7.4 Device Functional Modes........................................ 19
8
9
10 Layout................................................................... 33
10.1 Layout Guidelines ................................................. 33
10.2 Layout Example .................................................... 34
11 器件和文档支持 ..................................................... 35
11.1 器件支持................................................................ 35
11.2 文档支持................................................................ 35
11.3 接收文档更新通知 ................................................. 35
11.4 社区资源................................................................ 35
11.5 商标....................................................................... 35
11.6 静电放电警告......................................................... 35
11.7 Glossary................................................................ 35
12 机械、封装和可订购信息....................................... 35
7
4 修订历史记录
Changes from Original (February 2020) to Revision A
Page
•
•
Deleted AVDD supply condition and MIN MAX specification for internal reference. ............................................................. 6
Deleted AVDD supply condition and MIN MAX specification for internal reference. ............................................................. 6
2
Copyright © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
5 Pin Configuration and Functions
RTE Package
16-Pin WQFN
Top View
REFIO_A
REFGND_A
REFGND_B
REFIO_B
1
2
3
4
12
11
10
9
SDO_B
SDO_A
SCLK
CS
Thermal
Pad
Not to scale
Pin Functions
NAME
NO.
16
5
TYPE
DESCRIPTION
AINM_A
AINM_B
AINP_A
AINP_B
AVDD
Analog input
Analog input
Analog input
Analog input
Power supply
Digital input
Negative analog input, channel A
Negative analog input, channel B
Positive analog input, channel A
Positive analog input, channel B
Supply voltage for ADC operation
Chip-select signal; active low
15
6
14
9
CS
DVDD
7
Digital I/O supply
Power supply
Power supply
Power supply
Analog input/output
Analog input/output
Digital input
Digital I/O supply
GND
13
2
Device ground
REFGND_A
REFGND_B
REFIO_A
REFIO_B
SCLK
Reference A ground
3
Reference B ground
1
Reference voltage input/output, channel A
Reference voltage input/output, channel B
Clock for serial communication
Data input for serial communication
Data output A for serial communication, channel A and channel B
Data output B for serial communication, channel B
4
10
8
SDI
Digital input
SDO_A
SDO_B
11
12
Digital output
Digital output
Exposed thermal pad. TI recommends connecting this pin to the printed
circuit board (PCB) ground.
Thermal pad
Power supply
Copyright © 2020, Texas Instruments Incorporated
3
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
6 Specifications
6.1 Absolute Maximum Ratings
over operating ambient temperature range (unless otherwise noted)(1)
MIN
–0.3
–0.3
MAX
UNIT
AVDD to REFGND_x(2) or GND
DVDD to GND
6
6
V
V
Analog (AINP_x and AINM_x)(3) and reference input
REFGND_x – 0.3
AVDD + 0.3
V
(REFIO_x) voltage with respect to REFGND_x
Digital input voltage with respect to GND
REFGND_x
GND – 0.3
GND – 0.3
–10
DVDD + 0.3
GND + 0.3
10
V
V
Input current to any pin except supply pins
Junction temperature, TJ
mA
°C
°C
–40
125
Storage temperature, Tstg
–65
150
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) REFGND_x refers to REFGND_A and REFGND_B. REFIO_x refers to REFIO_A and REFIO_B.
(3) AINP_x refers AINP_A and AINP_B. AINM_x refers to AINM_A and AINM_B.
6.2 ESD Ratings
VALUE
UNIT
Human-body model (HBM), ANSI/ESDA/JEDEC JS-001(1)
±2000
V(ESD)
Electrostatic discharge
V
Charged-device model (CDM), per JEDEC specification
JESD22-C101(2)
±500
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
4
Copyright © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
PARAMETER
POWER SUPPLY
TEST CONDITIONS
MIN
TYP
MAX UNIT
VREF range, internal reference
4.5
4.5
5
5
5.5
5.5
VREF range, external reference VREF < 4.5 V
VREF range, external reference VREF > 4.5 V
2 x VREF range, internal reference
Analog supply voltage
(AVDD to AGND)
AVDD
VREF
5
5
5.5
5.5
5.5
5.5
V
V
5
2 x VREF range, external reference
2 x VREF
1.65
5
DVDD
Digital supply voltage
3.3
ANALOG INPUTS (Single-Ended Configuration)
VREF range
0
0
0
VREF
2 x VREF
VREF
Full-scale input range
(AINP_x to AINM_x)(1)
FSR
VINP
V
V
2 x VREF range
Absolute input voltage VREF range
(AINP_x to
REFGND_x)(2)
2 x VREF range, AVDD ≥ 2 x VREF
0
2 x VREF
Absolute input voltage
(AINM_x to
VINM
–0.1
0.1
V
REFGND_x)
ANALOG INPUTS (Pseudo-Differential Configuration)
VREF range
–VREF / 2
–VREF
0
VREF / 2
VREF
Full-scale input range
(AINP_x to AINM_x)(1)
FSR
VINP
V
V
2 x VREF range
Absolute input voltage VREF range
(AINP_x to
VREF
2 x VREF range
REFGND_x)
0
2 x VREF
VREF / 2 –
0.1
VREF / 2 +
0.1
VREF range
VREF / 2
VREF
Absolute input voltage
(AINM_x -REFGND_x)
VINM
V
2 x VREF range
VREF – 0.1
VREF + 0.1
EXTERNAL REFERENCE INPUT
REFIO_x(3) input
VREF range
2.4
2.4
2.5
2.5
AVDD
VREFIO
voltage
V
2 x VREF range
AVDD / 2
TEMPERATURE RANGE
TA
Ambient temperature
–40
25
125
°C
(1) AINP_x refers to analog input pins AINP_A and AINP_B. AINM_x refers to analog input pins AINM_A and AINM_B.
(2) REFGND_x refers to reference ground pins REFGND_A and REFGND_B.
(3) REFIO_x refers to voltage reference inputs REFIO_A and REFIO_B.
Copyright © 2020, Texas Instruments Incorporated
5
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
6.4 Thermal Information
ADS8355
RTE (WQFN)
16 PINS
33.3
THERMAL METRIC(1)
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
29.5
7.3
ΨJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.2
YJB
7.4
RθJC(bot)
0.9
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics
at AVDD = 5 V, DVDD = 2.35 V to 5.5 V, VREFIO_A = VREFIO_B = 5 V (external) and fSAMPLE = 1 MSPS (unless otherwise noted);
minimum and maximum values at TA = –40°C to 125°C; typical values are at TA = 25°C
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
RESOLUTION
Resolution
16
Bits
Bits
DC ACCURACY
NMC
No missing codes
16
–3
±1
±1
3
INL
Integral nonlinearity
LSB
VREF input range, internal VREF
2.5 V
=
=
–0.99
±0.5
±0.5
0.99
LSB
DNL
Differential nonlinearity
VREF input range, internal VREF
2.5 V
Input offset error
EIO match
–1
–1
±0.5
±0.5
1
1
EIO
mV
1
ADC_A to ADC_B
dEIO/dT
Input offset thermal drift
µV/°C
Referenced to the voltage at
REFIO_x
Gain error
–0.1
–0.1
±0.05
±0.05
±1
0.1
EG
%FS
EG match
ADC_A to ADC_B
0.1
Referenced to the voltage at
REFIO_x
dEG/dT
Gain error thermal drift
ppm/°C
AC ACCURACY
VREF input range
86
88
84
AVDD = 3.3 V, VREF input range,
internal VREF = 2.5 V
SNR
THD
Signal-to-noise ratio
dB
dB
VREF = 2.5 V internal / external, 2 x
VREF input range
84
–97
–97
VREF input range
AVDD = 3.3 V, VREF input range,
Total harmonic distortion internal VREF = 2.5 V
VREF = 2.5 V internal/external, 2 x
VREF input range
–97
6
Copyright © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Electrical Characteristics (continued)
at AVDD = 5 V, DVDD = 2.35 V to 5.5 V, VREFIO_A = VREFIO_B = 5 V (external) and fSAMPLE = 1 MSPS (unless otherwise noted);
minimum and maximum values at TA = –40°C to 125°C; typical values are at TA = 25°C
PARAMETER
TEST CONDITIONS
VREF input range
MIN
TYP
MAX UNIT
87.5
AVDD = 3.3 V, VREF input range,
internal VREF = 2.5 V
Signal-to-noise +
distortion
83
SINAD
SFDR
dB
VREF = 2.5 V internal / external, 2 x
VREF input range
83
100
100
VREF input range
AVDD = 3.3 V, VREF input range,
internal VREF = 2.5 V
Spurious-free dynamic
range
dB
VREF = 2.5 V internal/external, 2 x
VREF input range
100
ANALOG INPUTS
In sample mode
In hold mode
40
4
Ci
Input capacitance
pF
µA
Ilkg
Input leakage current
0.1
INTERNAL VOLTAGE REFERENCE
VREFIO_x
Reference output voltage REFDAC_x = 1FFh at 25°C
2.5
±3
V
VREF_A to VREF_B
REFDAC_x = 1FFh at 25°C
matching
VREF-match
mV
Reference output
capacitor
CREFIO
tREFON
10
8
µF
Reference output settling
time
ms
VOLTAGE REFERENCE INPUT
Average reference input
current
IREF
Per ADC
300
µA
External reference
capacitor
CREF
10
µF
µA
Ilkg(dc)
DC leakage current
±0.1
SAMPLING DYNAMICS
tA
Aperture delay
8
40
50
ns
ps
ps
tA match
ADC_A to ADC_B
tAJIT
Aperture jitter
DIGITAL INPUTS
DVDD ≥ 2.35 V
DVDD < 2.35 V
DVDD ≥ 2.35 V
DVDD < 2.35 V
0.7 x DVDD
0.8 x DVDD
–0.3
DVDD + 0.3
(1)
VIH
High-level input voltage
V
DVDD + 0.3
0.3 x DVDD
0.2 x DVDD
(1)
VIL
Low-level input voltage
Input current
V
–0.3
±10
nA
DIGITAL OUTPUTS
(1)
VOH
High-level output voltage IOH = 500-µA source
Low-level output voltage IOL = 500-µA sink
0.8 x DVDD
0
DVDD
V
V
(1)
VOL
0.2 x DVDD
(1) Specified by design.
Copyright © 2020, Texas Instruments Incorporated
7
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
Electrical Characteristics (continued)
at AVDD = 5 V, DVDD = 2.35 V to 5.5 V, VREFIO_A = VREFIO_B = 5 V (external) and fSAMPLE = 1 MSPS (unless otherwise noted);
minimum and maximum values at TA = –40°C to 125°C; typical values are at TA = 25°C
PARAMETER
POWER SUPPLY
TEST CONDITIONS
MIN
TYP
MAX UNIT
11
12
13
AVDD = 5 V, internal reference
AVDD = 5V, no conversion internal
reference
8
7
AVDD = 5 V, no conversion
external reference(2)
mA
AIDD
Analog supply current
AVDD = 5 V, STANDBY mode
internal reference
2.5
1
AVDD = 5 V, STANDBY mode
external reference(2)
Power-down mode
10
0.5
1
50
µA
DVDD = 3.3 V, Cload = 10 pF
DVDD = 5 V, Cload = 10 pF
DIDD
Digital supply current
mA
(2) With internal reference powered down, REF_SEL = 1.
6.6 Timing Requirements
at AVDD = 5 V, DVDD = 1.65 V to 5.5 V, and maximum throughput (unless otherwise noted); minimum and maximum values
at TA = –40°C to +125°C; typical values at TA = 25°C.
MIN
1
NOM
MAX
UNIT
DVDD ≥ 2.35 V
tCYCLE
Cycle time
µs
1.65 V < DVDD < 2.35 V
DVDD ≥ 2.35 V
1.5
50
24
fCLK
Serial clock frequency
Serial clock time period
MHz
ns
1.65 V < DVDD < 2.35 V
DVDD ≥ 2.35 V
20
42
tCLK
1.65 V < DVDD < 2.35 V
tPH_CK
tPL_CK
tACQ
Clock high time
Clock low time
0.45
0.45
350
40
0.55
0.55
tCLK
tCLK
ns
Acquisition time
CS high time, NOP
tPH_CS
ns
DVDD ≥ 2.35 V
12
Setup time: CS falling edge to SCLK
falling edge
tSU_CSCK
ns
1.65 V < DVDD < 2.35 V
20
Delay time: Last SCLK falling edge to CS
rising edge
tD_CKCS
tSU_CKDI
tHT_CKDI
12
2
ns
ns
ns
Setup time: DIN data valid to SCLK
falling edge
Hold time: SCLK falling edge to
(previous) data valid on DIN
2
8
Copyright © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
6.7 Switching Characteristics
at AVDD = 5 V, DVDD = 1.65 V to 5.5 V, and maximum throughput (unless otherwise noted); minimum and maximum values
at TA = –40°C to +125°C; typical values at TA = 25°C.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tCONV
Conversion time
650
ns
Delay time: CS falling edge to data
enable
DVDD ≥ 2.35 V
14.5
14.5
31
tDEN_CSDO
ns
ns
ns
Delay time: CS falling edge to data
enable
1.65 V < DVDD < 2.35 V
DVDD ≥ 2.35 V
Delay time: CS rising edge to data going
to 3-state
tDZ_CSDO
Delay time: CS rising edge to data going
to 3-state
1.65 V < DVDD < 2.35 V
DVDD ≥ 2.35 V
37
Delay time: SCLK falling edge to next
data valid
19.5
19.5
tD_CKDO
Delay time: SCLK falling edge to next
data valid
1.65 V < DVDD < 2.35 V
图 1 shows the details of the serial interface between the device and the digital host controller.
Sample
N+1
Sample
N
tCYCLE
tCONV
tACQ
tPH_CS
tCLK
CS
tD_CKCS
tPH_CK
SCLK
1
2
14
15
16
tSU_CSCK
tDZ_CSDO
tPL_CK
tDEN_CSDO
tD_CKDO
D0
SDO_A
SDO_B
D14
D2
D1
D15
Data from sample N
tHT_CKDI
tSU_CKDI
SDI
DMSB
图 1. Serial interface Timing Diagram
版权 © 2020, Texas Instruments Incorporated
9
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
6.8 Typical Characteristics
at TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (external), and fDATA = 1 MSPS (unless otherwise noted)
0
-40
0
-40
-80
-80
-120
-160
-200
-120
-160
-200
0
100
200 300
Frequency (kHz)
400
500
0
100
200 300
Frequency (kHz)
400
500
D001
D002
fIN = 2 kHz, SNR = 91.27 dB, THD = –96.78 dB
fIN = 2 kHz, SNR = 91.31 dB, THD = –96.04 dB
图 2. Typical FFT ADC A
图 3. Typical FFT ADC B
93
92
92.6
91.6
92.2
91.8
91.4
91
91.2
90.8
90.4
90
-50
0
50
Free-Air Temperature (°C)
100
150
-50
0
50
Free-Air Temperature (°C)
100
150
D003
D004
fIN = 2 kHz
fIN = 2 kHz
图 4. SNR vs Free-Air Temperature
图 5. SINAD vs Free-Air Temperature
-97
-97.4
-97.8
-98.2
-98.6
-99
95
93
91
89
87
85
-50
0
50
Free-Air Temperature (°C)
100
150
2
3
4
Reference Voltage (V)
5
6
D005
D006
fIN = 2 kHz
fIN = 2 kHz
图 6. THD vs Free-Air Temperature
图 7. SNR vs Reference Voltage
10
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Typical Characteristics (接下页)
at TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (external), and fDATA = 1 MSPS (unless otherwise noted)
-96
95
93
91
89
87
85
-97
-98
-99
-100
-101
2
3
4
Reference Voltage (V)
5
6
2
3
4
Reference Voltage (V)
5
6
D007
D008
fIN = 2 kHz
fIN = 2 kHz
图 8. SINAD vs Reference Voltage
图 9. THD vs Reference Voltage
2.55
2.53
2.51
2.49
2.47
2.45
50000
40000
30000
20000
10000
0
32765 32766 32767 32768 32769 32770 32771
Output Codes
-50
0
50
Free-Air Temperature (°C)
100
140
D009
D010
Number of samples = 65536, standard deviation = 0.59
VREFIO_x = 2.5 V
图 10. DC Histogram
图 11. Internal Reference vs Free-Air Temperature
1
0.1
0.6
0.2
-0.2
-0.6
-1
0.06
0.02
-0.02
-0.06
-0.1
-50
0
50
Free-Air Temperature (°C)
100
150
-50
0
50
Free-Air Temperature (°C)
100
150
D011
D012
图 12. Offset Error vs Free-Air Temperature
图 13. Gain Error vs Free-Air Temperature
版权 © 2020, Texas Instruments Incorporated
11
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
Typical Characteristics (接下页)
at TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (external), and fDATA = 1 MSPS (unless otherwise noted)
1
0.6
0.2
-0.2
-0.6
-1
1
0.6
0.2
-0.2
-0.6
-1
0
16384
32768
Codes
49152
65536
0
16384
32768
Codes
49152
65536
D013
D014
图 14. Differential Nonlinearity ADC A
图 15. Differential Nonlinearity ADC B
3
1.8
0.6
-0.6
-1.8
-3
3
1.8
0.6
-0.6
-1.8
-3
0
16384
32768
Codes
49152
65536
0
16384
32768
Codes
49152
65536
D015
D016
图 16. Integral Nonlinearity ADC A
图 17. Integral Nonlinearity ADC B
1
0.6
0.2
-0.2
-0.6
-1
3
1.8
0.6
-0.6
-1.8
-3
DNL min
DNL max
INL min
INL max
-50
0
50
Free-Air Temperature (°C)
100
150
-50
0
50
Free-Air Temperature (°C)
100
150
D017
D018
图 18. Differential Nonlinearity vs Free-Air Temperature
图 19. Integral Nonlinearity vs Free-Air Temperature
12
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Typical Characteristics (接下页)
at TA = 25°C, AVDD = 5 V, DVDD = 3.3 V, VREF = 2.5 V (external), and fDATA = 1 MSPS (unless otherwise noted)
1
0.6
0.2
-0.2
-0.6
-1
3
1.8
0.6
-0.6
-1.8
-3
DNL min
DNL max
INL min
INL max
2
3
4
Reference Voltage (V)
5
6
2
3
4
Reference Voltage (V)
5
6
D019
D020
图 20. Differential Nonlinearity vs Reference Voltage
图 21. Integral Nonlinearity vs Reference Voltage
12
14
AVDD = 3.3 V
AVDD = 5 V
AVDD = 3.3 V
AVDD = 5 V
11.2
13.2
12.4
11.6
10.8
10
10.4
9.6
8.8
8
-50
0
50
Free-Air Temperature (°C)
100
150
0
10
20 30
SCLK Freq (MHz)
40
50
D021
D022
图 22. Analog Supply Current vs Free-Air Temperature
图 23. Analog Supply Current vs SCLK Frequency
版权 © 2020, Texas Instruments Incorporated
13
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
7 Detailed Description
7.1 Overview
The ADS8355 is a 16-bit, 1-MSPS, dual, simultaneous-sampling, analog-to-digital converter (ADC) with an
integrated programmable reference. The ADS8355 supports single-ended and pseudo-differential input signals.
The device provides a simple, serial interface to the host controller and operates over a wide range of analog
and digital power supplies.
7.2 Functional Block Diagram
AVDD
DVDD
AINP_A
AINM_A
ADC A
CS
SCLK
REFIO_A
REFA
REFB
Serial
Interface
SDI
SDO_A
REFIO_B
SDO_B
AINP_B
AINM_B
ADC B
GND
7.3 Feature Description
7.3.1 Reference
The device has two simultaneous sampling ADCs: ADC_A and ADC_B. ADC_A and ADC_B operate with
reference voltages VREF_A and VREF_B present on the REFIO_A and REFIO_B pins, respectively. Decouple the
REFIO_A and REFIO_B pins with the REFGND_A and REFGND_B pins, respectively, with 10-µF decoupling
capacitors.
As illustrated in 图 24, the device supports operation either with an internal or external reference source. The
reference voltage source is determined by programming the INT_EXT bit of the REF_SEL register. This bit is
common to ADC_A and ADC_B.
14
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Feature Description (接下页)
AINP_A
ADC_A
AINM_A
REFGND_A
SW
REFDAC_A
10 µF
REFIO_A
REFIO_B
Enable
REF_SEL.B0
INTREF
10 µF
REFDAC_B
REFGND_B
AINP_B
ADC_B
AINM_B
图 24. Reference Configurations and Connections
The default value of the REF_SEL register bit INT_EXT is set to 0. The device ADC_A and ADC_B operate with
the external reference voltages provided on the REFIO_A and REFIO_B pins, respectively.
When the REF_SEL register bit INT_EXT is set to 1, the device operates with the internal reference source
connected to REFIO_A and REFIO_B. The individual reference voltages can be set independently by
programming the REFDAC_A and REFDAC_B values, respectively. For a 2.5-V internal reference, program
REFDAC_x with a 0x1FF value..
图 25 shows a typical transfer function for the internal REFDAC when the internal reference is enabled.
2.6
2.4
2.2
2
1.8
0
128
256
REFDAC_x Code
384
512
D023
图 25. REFDAC Transfer Function
7.3.2 Analog Inputs
The ADS8355 supports single-ended or pseudo-differential analog input signals on both ADC channels. These
inputs are sampled and converted simultaneously by the two ADCs, ADC_A and ADC_B. ADC_A samples and
converts (VAINP_A – VAINM_A), and ADC_B samples and converts (VAINP_B – VAINM_B).
图 26 depicts equivalent circuits for the ADC_A and ADC_B analog input pins. Series resistance, RS, represents
the on-state sampling switch resistance (typically 50 Ω) and CSAMPLE is the device sampling capacitor (typically
40 pF).
版权 © 2020, Texas Instruments Incorporated
15
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
Feature Description (接下页)
AVDD
AVDD
RS CSAMPLE
RS CSAMPLE
AINP_A
AINP_B
GND
GND
AVDD
AVDD
RS CSAMPLE
RS CSAMPLE
AINM_A
AINM_B
GND
GND
a) ADC_A
b) ADC_B
图 26. Equivalent Circuit for the Analog Input Pins
7.3.2.1 Analog Input: Full-Scale Range Selection
The full-scale range (FSR) supported at the analog inputs of the device is programmable with the RANGE_SEL
bit of the INPUT_CONFIG register. The RANGE_SEL bit has a default value of low. This bit is common for both
ADCs (ADC_A and ADC_B). 公式 1 and 公式 2 give the FSR.
RANGE_SEL = 0, FSR_ADC_A = 0 to VREF_A and FSR_ADC_B = 0 to VREF_B
(1)
(2)
For RANGE_SEL = 1, FSR_ADC_A = 0 to 2 × VREF_A and FSR_ADC_B = 0 to 2 × VREF_B
VREF_A and VREF_B are the reference voltages going to ADC_A and ADC_B, respectively (as described in the
Reference section).
When operating with internal reference mode, the maximum dynamic range of the ADC can be used by
programming the appropriate setting for the INPUT_CONFIG and REFDAC_x registers.
Ensure that the ADC analog supply (AVDD) meets the criteria defined in 公式 3 and 公式 4 when the
RANGE_SEL bit is set to 1.
2 × VREF_A ≤ AVDD ≤ AVDD(max)
2 × VREF_B ≤ AVDD ≤ AVDD(max)
(3)
(4)
7.3.2.2 Analog Input: Single-Ended and Pseudo-Differential Configurations
The ADS8355 can support single-ended or pseudo-differential input configuration. The device operates in single-
ended configuration by default.
The AINM_SEL bit in the INPUT_CONFIG register determines the input configuration used for the input pins.
The selection is common for both input channels.
Program the AINM_SEL pin to logic low to operate the device in single-ended input configuration. Connect the
AINM_A and AINM_B inputs to GND.
Program the AINM_SEL pin to logic high to operate the device in pseudo-differential input configuration. Connect
the AINM_A and AINM_B inputs to a voltage equivalent to FSR_ADC_A / 2 and FSR_ADC_B / 2, respectively.
表 1 summarizes the analog input pin connections based on the various user settings.
16
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Feature Description (接下页)
表 1. Input Configurations and Connections
INPUT RANGE
SELECTION
RANGE_SEL
INPUT CONFIGURATION SELECTION
AINP_X
AINM_X
AINM_SEL
Input signal range 0
to VREF_X
0
1
0
1
0
0
1
1
Connect to GND
Connect to GND
Input signal range 0
to 2 X VREF_X
Input signal range 0
to VREF_X
Connect to VREF_X / 2
Connect to VREF_X
Input signal range 0
to 2 X VREF_X
7.3.3 Transfer Function
The device supports two input configurations:
1. Default, single-ended inputs, INPUT_CONFIG register bit 0 = 0
2. Pseudo-differential inputs, INPUT_CONFIG register bit 0 = 1
The device supports two output data formats:
1. Default, straight binary output, DATA_OUT_CTRL register bit 0 = 0
2. Two's compliment output, DATA_OUT_CTRL register bit 0 = 1
公式 5 calculates the device resolution:
1 LSB = (FSR_ADC_x) / (2N)
where:
•
•
N = 16 and
FSR_ADC_x is the full-scale input range of the ADC
(5)
表 2 and 表 3 show the different input voltages and the corresponding output codes from the device.
表 2. Transfer Characteristics for Straight Binary Output (Default)
OUTPUT CODE (Hex)
STRAIGHT BINARY
INPUT VOLTAGE
AINM_x
INPUT
CONFIGURATION
AINP_x
≤ 1 LSB
AINP_x - AINM_x
≤ 1 LSB
CODE
ADS8355
0000
ZC
MC
FSC
ZC
Single-ended
FSR_ADC_x / 2
≥ FSR_ADC_x – 1 LSB
≤ 1 LSB
0
FSR_ADC_x / 2
7FFF
≥ FSR_ADC_x – 1 LSB
≤ –FSR_ADC_x / 2 + 1 LSB
0
FFFF
0000
Pseudo-differential
FSR_ADC_x / 2
≥ FSR_ADC_x – 1 LSB
FSR_ADC_x / 2
MC
FSC
7FFF
≥ FSR_ADC_x / 2 – 1 LSB
FFFF
表 3. Transfer Characteristics for Twos Compliment Output
OUTPUT CODE (Hex)
TWO'S COMPLIMENT
INPUT VOLTAGE
INPUT
CONFIGURATION
AINP_x
≤ 1 LSB
AINM_x
AINP_x - AINM_x
≤ 1 LSB
CODE
ADS8355
8000
NFSC
MC
Single-ended
FSR_ADC_x / 2
≥ FSR_ADC_x – 1 LSB
≤ 1 LSB
0
FSR_ADC_x / 2
0000
≥ FSR_ADC_x – 1 LSB
≤ –FSR_ADC_x / 2 + 1 LSB
0
PFSC
NFSC
MC
7FFF
8000
Pseudo-differential
FSR_ADC_x / 2
≥ FSR_ADC_x – 1 LSB
FSR_ADC_x / 2
0000
≥ FSR_ADC_x / 2 – 1 LSB
PFSC
7FFF
版权 © 2020, Texas Instruments Incorporated
17
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
图 27 shows the ideal device transfer characteristics for the single-ended analog input.
FSC
PFSC
MC
MC
NFSC
ZC
1 LSB
FSR_ADC_x/2
FSR_ADC_x œ 1 LSB
Single-Ended Analog Input
(AINP_x œ AINM_x)
图 27. Ideal Transfer Characteristics for a Single-Ended Analog Input
图 28 shows the ideal device transfer characteristics for the pseudo-differential analog input.
FSC
PFSC
-FSR_ADC_x/2 + 1 LSB
MC
MC
FSR_ADC_x/2 œ 1 LSB
ZC
NFSC
Psuedo-Differential Analog Input
(AINP_x œ AINM_x)
图 28. Ideal Transfer Characteristics for a Pseudo-Differential Analog Input
18
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
7.4 Device Functional Modes
7.4.1 Conversion Data Read: Dual-SDO Mode (Default)
The dual-SDO mode is designed to support the maximum throughput at lower SCLK frequencies.
The single-SDO mode is enabled by programming the SDO_MODE bit in the SDO_CTRL register to logic low. In
this mode, the SDO_A pin outputs the ADC_A conversion result and the SDO_B pin outputs the ADC_B
conversion result. 图 29 shows a detailed timing diagram for this mode.
CS
SCLK
1
2
14
15
16
D14
SDO_A
SDO_B
D2
D1
D0
D15
Data from ADC A
D14
D2
D1
D0
D15
Data from ADC B
图 29. Dual-SDO Mode Timing Diagram
A CS rising edge forces SDO_x to tri-state. CS also samples the input signal and causes the device to enter
conversion phase. Conversion is done with the internal clock. CS and SCLK must remain high for a minimum
time of tCONV. A CS falling edge brings the serial data bus out of tri-state and the device outputs the MSB of the
data. The lower data bits are output on the subsequent SCLK falling edges. SDO_A and SDO_B go low after the
16th SCLK falling edge. The SDO_x signals remain low until the CS signal is pulled high.
版权 © 2020, Texas Instruments Incorporated
19
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
Device Functional Modes (接下页)
7.4.2 Conversion Data Read: Single-SDO Mode
The single-SDO mode is designed to support operation with a wide variety of hosts that can support only one
master in, slave out (MISO) signal for the SPI interface. The maximum throughput is limited based on the SCLK
frequency supported by the host.
The single-SDO mode is enabled by programming the SDO_MODE bit in the SDO_CTRL register to logic high.
In this mode, the SDO_A pin outputs the conversion results for ADC_A followed by ADC_B. 图 30 shows a
detailed timing diagram for this mode.
CS
SCLK
1
2
18
15
16
17
31
32
D14
D14
SDO_A
D1
D1
D0
D15
D0
D15
Data from ADC A
Data from ADC B
图 30. Single-SDO Mode Timing Diagram
A CS rising edge forces SDO_x to tri-state. CS also samples the input signal and causes the device to enter
conversion phase. Conversion is done with the internal clock. CS and SCLK must remain high for a minimum
time of tCONV. A CS falling edge brings the serial data bus out of tri-state and the device outputs the MSB of the
ADC_A conversion result. The lower data bits are output on the subsequent SCLK falling edges. After ADC_A,
the device outputs the ADC_B conversion result starting from 17th falling edge of SCLK. SDO_A drives the
output line to a zero logic level after 32nd falling edge of SCLK. SDO_A remains low until the CS signal is pulled
high. SDO_B is driven low when the SPI interface is active in single-SDO mode.
7.4.3 Low-Power Modes
In normal mode of operation, all internal circuits of the device are always powered up and the device is ready to
commence a new conversion when CS is pulled high. The device also supports two low-power modes to
optimize the power consumption at lower throughput or when the device is not expected to perform conversions.
7.4.3.1 STANDBY Mode
The device supports a standby mode of operation where the ADCs and the internal oscillator are powered down
to save power. The internal reference, if already enabled, stays enabled and the contents of the REFDAC_A and
REFDAC_B registers are retained to enable faster power-up to a normal mode of operation.
Standby mode is enabled by programming the PD_KEY register with 0x09h followed by setting the STANDBY bit
in the PD_STANDBY register with logic high. See the Register Map section for the register setting information.
See the Register Read/Write Operation section for timing information for register access.
Standby mode is disabled by programming the PD_KEY register with 0x09h followed by setting the STANDBY bit
in the PD_STANDBY register with logic low. After existing standby mode, a delay of 10 µs must elapse for the
internal circuits to power up and resume normal operation.
7.4.3.2 PD (Power-Down) Mode
The device supports a PD (power-down) mode of operation where all internal blocks except the interface and I/O
are powered down to save power.
PD mode is enabled by programming the PD_KEY register with 0x09h followed by setting the PD_EN bit in the
PD_STANDBY register with logic high. See the Register Map section for the register setting information. See the
Register Read/Write Operation section for timing information for register access.
20
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Device Functional Modes (接下页)
PD mode is disabled by programming the PD_KEY register with 0x09h followed by setting the PD_EN bit in the
PD_STANDBY register with logic low. After exiting PD mode, a delay of 1 ms must elapse with the external
reference mode and 3 ms must elapse with the internal reference mode for the internal circuits to power up and
resume normal operation.
7.5 Programming
7.5.1 Register Read/Write Operation
This device features configuration registers and supports the commands listed in 表 4 to access the internal
configuration registers.
表 4. Supported Commands
COMMAND
ACRONYM
B[19:16]
B[15:8]
B[7:0]
COMMAND DESCRIPTION
No operation. Next frame provides the ADC conversion result
output on the SDO_X lines.
0000
00000000000
00000000
NOP
0001
0010
<8-bit address>
<8-bit address>
<8-bit data>
00000000
WR_REG
RD_REG
Write <8-bit data> to the <8-bit address>
Read contents from the <8-bit address>
<8-bit
unmasked bits>
0011
0100
<8-bit address>
<8-bit address>
xxxxxxxxx
SET_BITS
CLR_BITS
Reserved
Set <8-bit unmasked bits> from <8-bit address>
Clear <8-bit unmasked bits> from <8-bit address>
<8-bit
unmasked bits>
Remaining
combinations
These commands are reserved and treated by the device as no
operation.
xxxxxxxx
The ADS8355 supports two types of data transfer operations: data write (the host controller configures the
device), and data read (the host controller reads data from the device).
Any data write to the device is always synchronous to the external clock provided on the SCLK pin. The
WR_REG command writes the 8-bit data into the 8-bit address specified in the command string. The CLR_BITS
command clears the specified bits (identified by 1) at the 8-bit address (without affecting the other bits), and the
SET_BITS command sets the specified bits (identified by 1) at the 8-bit address (without affecting the other bits).
图 31 shows the digital waveform for a register read operation. A register read operation consists of two frames:
one frame to initiate a register read and a second frame to read data from the register address provided in the
first frame. As shown in 图 31, the 8-bit register address and the 8-bit dummy data are sent over the SDI pin
during the first 20-bit frame with the read command (0010b). The 20-bit command information is right-aligned
with the frame. If a command frame is smaller than 20 bits, the contents of the command are discarded. If a
frame has more than 20 bits, the last 20 bits are used to decode the operation. When CS goes from low to high,
this read command is decoded and the requested register data are available for reading during the next frame.
During the second frame, the first eight bits on SDO_A correspond to the requested register read. During the
second frame, SDI can be used to initiate another operation or can be set to 0.
CS
SCLK
18
18
1
2
5
6
7
16
17
20
1
2
5
6
7
16
17
20
Optional; Can set SDI = 0
8-bit Address
0010b
(RD_REG)
SDI
8-bit Address
0000 0000b
Command
8-bit Data
SDO_A
8-bit Register Data
图 31. Register Read Operation
版权 © 2020, Texas Instruments Incorporated
21
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
图 32 shows that for writing data to the register, one 20-bit frame is required. The frame contents are right-
aligned. If a command frame is smaller than 20 bits, the contents of the command are discarded. If a frame has
more than 20 bits, the last 20 bits are used to decode the operation. The 20-bit data on SDI consists of a 4-bit
write command (0001b), set bit command (0011b), or clear bit command (0100b), an 8-bit register address, and
8-bit data. The write command is decoded on the CS rising edge and the specified register is updated with the 8-
bit data specified during the register write operation.
CS
SCLK
18
1
2
5
6
7
16
17
20
0001b
(WR_REG)
SDI
8-bit Address
8-bit Data
图 32. Register Write Operation
22
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
7.6 Register Map
7.6.1 ADS8355 Registers
Table 5 lists the ADS8355 registers. All register offset addresses not listed in Table 5 should be considered as
reserved locations and the register contents should not be modified.
Table 5. ADS8355 Registers
Offset
Acronym
Register Name
Section
4h
PD_STANDBY
Power down configuration register
PD_STANDBY
Register (Offset =
4h) [reset = 0h]
5h
Dh
PD_KEY
Power down key register
SDO mode selection register
Output data format register
PD_KEY Register
(Offset = 5h)
[reset = 0h]
SDO_CTRL
SDO_CTRL
Register (Offset =
Dh) [reset = 0h]
11h
DATA_OUT_CTRL
DATA_OUT_CTR
L Register (Offset
= 11h) [reset =
0h]
20h
24h
25h
26h
27h
28h
REF_SEL
ADC reference selection register
REF_SEL
Register (Offset =
20h) [reset = 0h]
REFDAC_A_LSB
REFDAC_A_MSB
REFDAC_B_LSB
REFDAC_B_MSB
INPUT_CONFIG
REFDACA configuration register (LSB)
REFDACA configuration register (MSB)
REFDACB configuration register (LSB)
REFDACB configuration register (MSB)
Analog input configuration register
REFDAC_A_LSB
Register (Offset =
24h) [reset = 0h]
REFDAC_A_MSB
Register (Offset =
25h) [reset = 0h]
REFDAC_B_LSB
Register (Offset =
26h) [reset = 0h]
REFDAC_B_MSB
Register (Offset =
27h) [reset = 0h]
INPUT_CONFIG
Register (Offset =
28h) [reset = 0h]
Complex bit access types are encoded to fit into small table cells. Table 6 shows the codes that are used for
access types in this section.
Table 6. ADS8355 Access Type Codes
Access Type
Read Type
R
Code
Description
R
Read
Write Type
W
W
Write
Reset or Default Value
-n
Value after reset or the default
value
Register Array Variables
Copyright © 2020, Texas Instruments Incorporated
23
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
Table 6. ADS8355 Access Type Codes (continued)
Access Type
Code
Description
i,j,k,l,m,n
When these variables are used in
a register name, an offset, or an
address, they refer to the value of
a register array where the register
is part of a group of repeating
registers. The register groups form
a hierarchical structure and the
array is represented with a
formula.
y
When this variable is used in a
register name, an offset, or an
address it refers to the value of a
register array.
7.6.1.1 PD_STANDBY Register (Offset = 4h) [reset = 0h]
PD_STANDBY is shown in Figure 33 and described in Table 7.
Return to the Summary Table.
Power down configuration register
Figure 33. PD_STANDBY Register
7
6
5
4
3
2
1
0
RESERVED
R-00000b
STANDBY
R/W-0b
PD_EN
R/W-0b
RESERVED
R-0b
Table 7. PD_STANDBY Register Field Descriptions
Bit
Field
Type
R
Reset
00000b
0b
Description
7-3
2
RESERVED
STANDBY
R/W
This bit enables partial powerdown of ADCs and internal oscillator ,
all other blocks are active
0b = Disable partial power down
1b = Enable partial power down
1
0
PD_EN
R/W
R
0b
0b
This bit enables all blocks to powerdown except the interface and IO
0b = Disable power down
1b = Enable power down
RESERVED
7.6.1.2 PD_KEY Register (Offset = 5h) [reset = 0h]
PD_KEY is shown in Figure 34 and described in Table 8.
Return to the Summary Table.
Power down key register
Figure 34. PD_KEY Register
7
6
5
4
3
2
1
0
RESERVED
R-0000b
PD_WKEY[3:0]
R/W-0000b
Table 8. PD_KEY Register Field Descriptions
Bit
Field
Type
R
Reset
0000b
0000b
Description
7-4
3-0
RESERVED
PD_WKEY[3:0]
R/W
Writing 1001 to these bits enable register write operation to
PD_STANDBY register.
24
Copyright © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
7.6.1.3 SDO_CTRL Register (Offset = Dh) [reset = 0h]
SDO_CTRL is shown in Figure 35 and described in Table 9.
Return to the Summary Table.
SDO mode selection register
Figure 35. SDO_CTRL Register
7
6
5
4
3
2
1
0
RESERVED
R-0000000b
SDO_MODE
R/W-0b
Table 9. SDO_CTRL Register Field Descriptions
Bit
Field
Type
R
Reset
0000000b
0b
Description
7-1
0
RESERVED
SDO_MODE
R/W
This bit selects ADC to output data in either single SDO or Dual
SDO mode.
0b = data out on both SDO_A and SDO_B
1b = data out on SDO_A only
7.6.1.4 DATA_OUT_CTRL Register (Offset = 11h) [reset = 0h]
DATA_OUT_CTRL is shown in Figure 36 and described in Table 10.
Return to the Summary Table.
Output data format register
Figure 36. DATA_OUT_CTRL Register
7
6
5
4
3
2
1
0
RESERVED
OP_DATA_FO
RMAT
R-0000000b
R/W-0b
Table 10. DATA_OUT_CTRL Register Field Descriptions
Bit
Field
Type
R
Reset
0000000b
0b
Description
7-1
0
RESERVED
OP_DATA_FORMAT
R/W
This bit selects ADC output data format.
0b = Straight Binary format
1b = 2's complements format
7.6.1.5 REF_SEL Register (Offset = 20h) [reset = 0h]
REF_SEL is shown in Figure 37 and described in Table 11.
Return to the Summary Table.
ADC reference selection register
Figure 37. REF_SEL Register
7
6
5
4
3
2
1
0
RESERVED
R-0000000b
INT_EXT
R/W-0b
Copyright © 2020, Texas Instruments Incorporated
25
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
Table 11. REF_SEL Register Field Descriptions
Bit
7-1
0
Field
Type
R
Reset
0000000b
0b
Description
RESERVED
INT_EXT
R/W
This bit selects ADC reference source.
0b = Device uses external reference for ADC conversion
1b = Device uses internal reference for ADC conversion
7.6.1.6 REFDAC_A_LSB Register (Offset = 24h) [reset = 0h]
REFDAC_A_LSB is shown in Figure 38 and described in Table 12.
Return to the Summary Table.
REFDACA configuration register (LSB)
Figure 38. REFDAC_A_LSB Register
7
6
5
4
3
2
1
0
REFDAC_A_LSB[7:0]
R/W-00000000b
Table 12. REFDAC_A_LSB Register Field Descriptions
Bit
7-0
Field
REFDAC_A_LSB[7:0]
Type
Reset
Description
R/W
00000000b Least significant byte to program the REFDAC_A.
REFDAC_A _MSB and REFDAC_A_LSB in combination are used to
set the internal reference for ADC_A. For 2.5V internal reference,
program 0x1FF to REFDAC_A.
7.6.1.7 REFDAC_A_MSB Register (Offset = 25h) [reset = 0h]
REFDAC_A_MSB is shown in Figure 39 and described in Table 13.
Return to the Summary Table.
REFDACA configuration register (MSB)
Figure 39. REFDAC_A_MSB Register
7
6
5
4
3
2
1
0
RESERVED
REFDAC_A_M
SB
R/W-00000000b
Table 13. REFDAC_A_MSB Register Field Descriptions
Bit
Field
Type
R
Reset
0000000b
0b
Description
7-1
0
RESERVED
REFDAC_A_MSB
R/W
Most significant bit to program the REFDAC_A.
REFDAC_A _MSB and REFDAC_A_LSB in combination are used to
set the internal reference for ADC_A. For 2.5V internal reference,
program 0x1FF to REFDAC_A.
7.6.1.8 REFDAC_B_LSB Register (Offset = 26h) [reset = 0h]
REFDAC_B_LSB is shown in Figure 40 and described in Table 14.
Return to the Summary Table.
REFDACB configuration register (LSB)
26
Copyright © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Figure 40. REFDAC_B_LSB Register
7
6
5
4
3
2
1
0
REFDAC_B_LSB[7:0]
R/W-00000000b
Table 14. REFDAC_B_LSB Register Field Descriptions
Bit
Field
REFDAC_B_LSB[7:0]
Type
Reset
Description
7-0
R/W
00000000b Least significant byte to program the REFDAC_B.
REFDAC_B_MSB and REFDAC_B_LSB in combination are used to
set the internal reference for ADC_B. For 2.5V internal reference,
program 0x1FF to REFDAC_B.
7.6.1.9 REFDAC_B_MSB Register (Offset = 27h) [reset = 0h]
REFDAC_B_MSB is shown in Figure 41 and described in Table 15.
Return to the Summary Table.
REFDACB configuration register (MSB)
Figure 41. REFDAC_B_MSB Register
7
6
5
4
3
2
1
0
RESERVED
REFDAC_B_M
SB
R/W-00000000b
Table 15. REFDAC_B_MSB Register Field Descriptions
Bit
Field
Type
R
Reset
0000000b
0b
Description
7-1
0
RESERVED
REFDAC_B_MSB
R/W
Most significant bit to program the REFDAC_B.
REFDAC_B _MSB and REFDAC_B_LSB in combination are used to
set the internal reference for ADC_B. For 2.5V internal reference,
program 0x1FF to REFDAC_B.
7.6.1.10 INPUT_CONFIG Register (Offset = 28h) [reset = 0h]
INPUT_CONFIG is shown in Figure 42 and described in Table 16.
Return to the Summary Table.
Analog input configuration register
Figure 42. INPUT_CONFIG Register
7
6
5
4
3
2
1
0
RESERVED
R-000000b
RANGE_SEL
R/W-0b
AINM_SEL
R/W-0b
Table 16. INPUT_CONFIG Register Field Descriptions
Bit
Field
Type
R
Reset
000000b
0b
Description
7-2
1
RESERVED
RANGE_SEL
R/W
This bit selects ADC input full scale range
0b = ADC operates with full scale range of 0 to VREF
1b = ADC operates with full scale range of 0 to 2 X VREF
Copyright © 2020, Texas Instruments Incorporated
27
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
Table 16. INPUT_CONFIG Register Field Descriptions (continued)
Bit
Field
Type
Reset
Description
0
AINM_SEL
R/W
0b
This bit selects ADC input configuration
0b = ADC operates in single-ended configuration. AINM pin must be
connected to GND potential.
1b = ADC operates in pseudo-differential configuration. AINM pin
must be connected to FSR / 2 potential.
8 Application and Implementation
注
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The two primary circuits required to maximize the performance of a high-precision, successive approximation
register (SAR), analog-to-digital converter (ADC) are the input driver and the reference driver circuits. This
section details some general principles for designing these circuits, and some application circuits designed using
these devices.
The device supports operation either with an internal or external reference source. See the Reference section for
details about the decoupling requirements.
The reference source to the ADC must provide low-drift and very accurate DC voltage and support the dynamic
charge requirements without affecting the noise and linearity performance of the device. The output broadband
noise (typically in the order of a few 100 µVRMS) of the reference source must be appropriately filtered by using a
low-pass filter with a cutoff frequency of a few hundred hertz. After band-limiting the noise from the reference
source, the next important step is to design a reference buffer that can drive the dynamic load posed by the
reference input of the ADC. At the start of each conversion, the reference buffer must regulate the voltage of the
reference pin within 1 LSB of the intended value. This condition necessitates the use of a large filter capacitor at
the reference pin of the ADC. The amplifier selected to drive the reference input pin must be stable while driving
this large capacitor and must have low output impedance, low offset, and temperature drift specifications. To
reduce the dynamic current requirements and crosstalk between the channels, a separate reference buffer is
recommended for driving the reference input of each ADC channel.
The input driver circuit for a high-precision ADC mainly consists of two parts: a driving amplifier and a fly-wheel
RC filter. The amplifier is used for signal conditioning of the input voltage and its low output impedance provides
a buffer between the signal source and the switched capacitor inputs of the ADC. The RC filter helps attenuate
the sampling charge injection from the switched-capacitor input stage of the ADC and functions as an charge
kickback filter to band-limit the wideband noise contributed by the front-end circuit. Careful design of the front-
end circuit is critical to meet the linearity and noise performance of a high-precision ADC.
8.1.1 Input Amplifier Selection
Selection criteria for the input amplifiers is highly dependent on the input signal type and the performance goals
of the data acquisition system. Some key amplifier specifications to consider when selecting an appropriate
amplifier to drive the inputs of the ADC are:
•
Small-signal bandwidth. Select the small-signal bandwidth of the input amplifiers to be as high as possible
after meeting the power budget of the system. Higher bandwidth reduces the closed-loop output impedance
of the amplifier, thus allowing the amplifier to more easily drive the low cutoff frequency RC filter at the ADC
inputs. Higher bandwidth also minimizes the harmonic distortion at higher input frequencies. Select the
amplifier bandwidth as described in 公式 6 to maintain the overall stability of the input driver circuit:
≈
’
1
∆
∆
÷
÷
Unity - Gain Bandwidth í 4ì
2p
ì(RFLT + RFLT )ìCFLT
«
◊
(6)
28
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Application Information (接下页)
•
Noise. Noise contribution of the front-end amplifiers must be as low as possible to prevent any degradation in
SNR performance of the system. As a rule of thumb, to ensure that the noise performance of the data
acquisition system is not limited by the front-end circuit, keep the total noise contribution from the front-end
circuit below 20% of the input-referred noise of the ADC. 公式 7 calculates noise from the input driver circuit.
This noise is band-limited by designing a low cutoff frequency RC filter:
2
SNR dB
(
20
)
≈
∆
’
÷
V
≈
∆
’
÷
-
1
f
_ AMP_PP
p
2
1
5
VREF
2
NG ì 2 ì
+ en2_RMS
ì
ì f-3dB
Ç
ì
ì10
«
◊
∆
∆
÷
÷
6.6
«
◊
where:
•
•
•
•
V1/f_AMP_PP = the peak-to-peak flicker noise in µV
en_RMS = the amplifier broadband noise density in nV/√Hz
f–3dB = the 3-dB bandwidth of the RC filter
NG = the noise gain of the front-end circuit, which is equal to 1 in a buffer configuration
(7)
•
Distortion. Both the ADC and the input driver introduce nonlinearity in a data acquisition block. As a rule of
thumb, the distortion of the input driver must be at least 10 dB lower than the distortion of the ADC, as shown
in 公式 8, to ensure that the distortion performance of the data acquisition system is not limited by the front-
end circuit.
THDAMP Ç THDADC - 10
dB
(8)
•
Settling Time. For DC signals with fast transients that are common in a multiplexed application, the input
signal must settle to the desired accuracy at the inputs of the ADC during the acquisition time window. This
condition is critical to maintain the overall linearity performance of the ADC. Typically, the amplifier data
sheets specify the output settling performance only up to 0.1% to 0.001%, which may not be sufficient for the
desired accuracy. Therefore, always verify the settling behavior of the input driver with TINA™-SPICE
simulations before selecting the amplifier.
8.1.2 Charge Kickback Filter
Converting analog-to-digital signals requires sampling an input signal at a constant rate. Any higher frequency
content in the input signal beyond half the sampling frequency is digitized and folded back into the low-frequency
spectrum. This process is called aliasing. Therefore, an analog, charge kickback filter must be used to remove
the harmonic content from the input signal before being sampled by the ADC. A charge kickback filter is
designed as a low-pass, RC filter, for which the 3-dB bandwidth is optimized based on specific application
requirements. For DC signals with fast transients (including multiplexed input signals), a high-bandwidth filter is
designed to allow accurately settling the signal at the ADC inputs during the small acquisition time window. For
AC signals, keep the filter bandwidth low to band-limit the noise fed into the ADC input, thereby increasing the
signal-to-noise ratio (SNR) of the system.
A filter capacitor, CFLT, connected across the ADC inputs (see 图 43), filters the noise from the front-end drive
circuitry, reduces the sampling charge injection, and provides a charge bucket to quickly charge the internal
sample-and-hold capacitors during the acquisition process. As a rule of thumb, the value of this capacitor must
be at least 10 times the specified value of the ADC sampling capacitance. For these devices, the input sampling
capacitance is equal to 40 pF. Thus, the value of CFLT must be greater than 400 pF. The capacitor must be a
COG- or NPO-type because these capacitor types have a high-Q, low-temperature coefficient, and stable
electrical characteristics under varying voltages, frequency, and time.
版权 © 2020, Texas Instruments Incorporated
29
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
Application Information (接下页)
AVDD
RFLT
1
CFLT
AINP_x
ADS8355
AINM_x
f-3db
=
2Œ ì RFLT ì CFLT
GND
RFLT
CFLT
GND
图 43. Charge Kickback Filter
Driving capacitive loads can degrade the phase margin of the input amplifiers, thus making the amplifier
marginally unstable. To avoid amplifier stability issues, series isolation resistors (RFLT) are used at the output of
the amplifiers. A higher value of RFLT is helpful from the amplifier stability perspective, but adds distortion as a
result of interactions with the nonlinear input impedance of the ADC. Distortion increases with source impedance,
input signal frequency, and input signal amplitude. Therefore, the selection of RFLT requires balancing the stability
and distortion of the design. For more information on ADC input R-C filter component selection, see the TI
Precision Labs on ti.com.
8.2 Typical Application
Input Driver
AVDD
AVDD
OPA320
œ
49 ꢀ
AINP_x
+
3.3 nF
3.3 nF
ADS8355
+
VIN
œ
AINM_x
GND
49 ꢀ
VDC
NOTE: Only one ADC channel is shown in this diagram. Replicate the same circuit for the other ADC channel.
图 44. DAQ Circuit: Maximum SINAD for a 10-kHz Input Signal at Full Throughput
30
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
Typical Application (接下页)
AVDD
10 µF
REFGND_A
ADC_A
AVDD
0.1 ꢀ
œ
1 kꢀ
REFIO_A
+
REF3425
1µF
ADS8355
VOUT
10 µF
AVDD
œ
1 kꢀ
REFIO_B
+
ADC_B
0.1 ꢀ
1µF
REFGND_B
10 µF
OPA2320
图 45. Reference Drive Circuit
8.2.1 Design Requirements
表 17 lists the target specifications for this application.
表 17. Target Specifications
TARGET SPECIFICATIONS
TEST CONDITIONS
10-kHz input signal frequency, 1-MSPS throughput
> 83-dB SNR, < –95-dB THD
8.2.2 Detailed Design Procedure
Best practice is for the distortion from the input driver to be at least 10 dB less than the ADC distortion. The
distortion resulting from variation in the common-mode signal is eliminated by using the amplifier in an inverting
gain configuration that establishes a fixed common-mode level for the circuit. This configuration also eliminates
the requirement of rail-to-rail swing at the amplifier input. The low-power OPA320, used as an input driver,
provides exceptional AC performance because of its extremely low-distortion and high-bandwidth specifications.
In addition, the components of the antialiasing filter are such that the noise from the front-end circuit is kept low
without adding distortion to the input signal.
The application circuit illustrated in 图 44 is optimized to achieve the lowest distortion and lowest noise for a
10-kHz input signal fed to the ADS8355 operating at full throughput with the default dual-SDO interface mode.
The input signal is processed through a high-bandwidth, low-distortion amplifier in an inverting gain configuration
and a low-pass RC filter before being fed into the device.
图 45 illustrates the reference driver circuit when operation with an external reference is desired. The reference
voltage is generated by the high-precision, low-noise REF3425 circuit. The output broadband noise of the
reference is heavily filtered by a low-pass filter with a 3-dB cutoff frequency of 160 Hz. The decoupling capacitor
on each reference pin is selected to be 10 µF. The low output impedance, low noise, and fast settling time make
the OPA2320 a good choice for driving this high capacitive load.
版权 © 2020, Texas Instruments Incorporated
31
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
8.2.3 Application Curve
To minimize external components and to maximize the dynamic range of the ADC, the device is configured to
operate with an internal reference (REF_SEL register, INT_EXT bit = 1) and a 2 × VREF_x input full-scale range
(INPUT_CONFIG register, RANGE_SEL bit = 1). The REFDAC_x registers are programmed to 0x1FFh to
program the internal reference to 2.5 V.
图 46 shows the FFT plot and test result obtained with the ADS8355 operating at full throughput with a dual-SDO
interface and the circuit configuration of 图 44.
0
-40
-80
-120
-160
-200
0
100
200 300
Frequency (kHz)
400
500
D024
SNR = 86.38 dB, THD = –97.24 dB, fIN = 10 kHz
图 46. The ADS8355 in Dual-SDO Interface Mode
32
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
9 Power Supply Recommendations
The device has two separate power supplies: AVDD and DVDD. The device operates on AVDD; DVDD is used
for the interface circuits. AVDD and DVDD can be independently set to any value within the permissible ranges.
When using the device with the 2 × VREF input range (INPUT_CONFIG register, RANGE_SEL bit = 1), the AVDD
supply voltage value defines the permissible voltage swing on the analog input pins. AVDD must be set as
described in 公式 3 and 公式 4 to avoid saturation of output codes and to use the full dynamic range on the
analog input pins.
Decouple the AVDD and DVDD pins, as shown in 图 47, with the GND pin using individual 10-µF decoupling
capacitors.
ADS8355
AVDD
AVDD
10 …F
GND
10 …F
DVDD
DVDD
图 47. Power-Supply Decoupling
10 Layout
10.1 Layout Guidelines
图 48 provides a board layout example for the device WQFN package. Partition the printed circuit board (PCB)
into analog and digital sections. Avoid crossing digital lines with the analog signal path and keep the analog input
signals and the reference input signals away from noise sources. As illustrated in 图 48, the analog input and
reference signals are routed on the left side of the board and the digital connections are routed on the right side
of the device.
The power sources to the device must be clean and well-bypassed. Use 10-µF, ceramic bypass capacitors in
close proximity to the analog (AVDD) and digital (DVDD) power-supply pins. Avoid placing vias between the
AVDD and DVDD pins and the bypass capacitors. Connect all ground pins to the ground plane using short, low
impedance paths.
The REFIO_A and REFIO_B reference inputs and outputs are bypassed with 10-µF, X7R-grade, 0805-size, 16-V
rated ceramic capacitors (CREF_x). Place the reference bypass capacitors as close as possible to the reference
REFIO_x pins and connect the bypass capacitors using short, low-inductance connections. Avoid placing vias
between the REFIO_x pins and the bypass capacitors.
The fly-wheel RC filters are placed immediately next to the input pins. Among ceramic surface-mount capacitors,
COG (NPO) ceramic capacitors provide the best capacitance precision. The type of dielectric used in COG
(NPO) ceramic capacitors provides the most stable electrical properties over voltage, frequency, and temperature
changes.
版权 © 2020, Texas Instruments Incorporated
33
ADS8355
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
www.ti.com.cn
10.2 Layout Example
CAVDD
CDVDD
图 48. Recommended Layout
34
版权 © 2020, Texas Instruments Incorporated
ADS8355
www.ti.com.cn
ZHCSKR7A –FEBRUARY 2020–REVISED FEBRUARY 2020
11 器件和文档支持
11.1 器件支持
11.1.1 开发支持
德州仪器 (TI),TI 高精度实验室
11.2 文档支持
11.2.1 相关文档
请参阅如下相关文档:
•
德州仪器 (TI),《具有关断功能的 OPAx320x 高精度 20MHz、0.9pA、低噪声 RRIO CMOS 运算放大器》 数
据表
•
德州仪器 (TI),《REF34xx 低漂移、低功耗、小封装串联电压基准》 数据表
11.3 接收文档更新通知
要接收文档更新通知,请导航至 ti.com.cn 上的器件产品文件夹。单击右上角的通知我进行注册,即可每周接收产
品信息更改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
11.4 社区资源
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.5 商标
TINA, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
11.6 静电放电警告
这些装置包含有限的内置 ESD 保护。 存储或装卸时,应将导线一起截短或将装置放置于导电泡棉中,以防止 MOS 门极遭受静电损
伤。
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知,且
不会对此文档进行修订。如需获取此数据表的浏览器版本,请查阅左侧的导航栏。
版权 © 2020, Texas Instruments Incorporated
35
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
ADS8355IRTER
ADS8355IRTET
ACTIVE
ACTIVE
WQFN
WQFN
RTE
RTE
16
16
3000 RoHS & Green
250 RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
8355
8355
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Sep-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
ADS8355IRTER
WQFN
RTE
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Sep-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
WQFN RTE 16
SPQ
Length (mm) Width (mm) Height (mm)
350.0 350.0 43.0
ADS8355IRTER
3000
Pack Materials-Page 2
GENERIC PACKAGE VIEW
RTE 16
3 x 3, 0.5 mm pitch
WQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
This image is a representation of the package family, actual package may vary.
Refer to the product data sheet for package details.
4225944/A
www.ti.com
PACKAGE OUTLINE
RTE0016D
WQFN - 0.8 mm max height
S
C
A
L
E
4
.
0
0
0
PLASTIC QUAD FLATPACK - NO LEAD
3.15
2.85
A
B
PIN 1 INDEX AREA
3.15
2.85
C
0.8
0.7
SEATING PLANE
0.08 C
0.05
0.00
2X 1.5
SYMM
(0.2) TYP
5
8
EXPOSED
THERMAL PAD
4
9
SYMM
17
2X 1.5
0.8 0.1
12X 0.5
1
12
PIN 1 ID
0.30
0.18
16X
16
13
0.5
0.3
0.1
C A B
16X
0.05
4219118/A 11/2018
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
RTE0016D
WQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(
0.8)
SYMM
SEE SOLDER MASK
DETAIL
16
13
16X (0.6)
12
16X (0.24)
1
17
SYMM
(2.8)
12X (0.5)
(R0.05) TYP
4
9
(
0.2) TYP
VIA
5
8
(2.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL UNDER
SOLDER MASK
METAL EDGE
EXPOSED METAL
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDER MASK DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4219118/A 11/2018
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
RTE0016D
WQFN - 0.8 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(
0.76)
16
13
16X (0.6)
1
12
16X (0.24)
17
SYMM
12X (0.5)
(2.8)
9
4
(R0.05) TYP
5
8
SYMM
(2.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 MM THICK STENCIL
SCALE: 20X
EXPOSED PAD 17
90% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
4219118/A 11/2018
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022,德州仪器 (TI) 公司
相关型号:
ADS8361IDBQ
Dual, 500kSPS, 16-Bit, 2 + 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
BB
ADS8361IDBQ
Dual, 500kSPS, 16-Bit, 2 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
TI
ADS8361IDBQG4
Dual, 500kSPS, 16-Bit, 2 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
TI
ADS8361IDBQR
Dual, 500kSPS, 16-Bit, 2 + 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
BB
ADS8361IDBQR
Dual, 500kSPS, 16-Bit, 2 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
TI
ADS8361IDBQRG4
Dual, 500kSPS, 16-Bit, 2 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
TI
ADS8361IRHBR
Dual, 500kSPS, 16-Bit, 2 + 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
BB
ADS8361IRHBR
Dual, 500kSPS, 16-Bit, 2 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
TI
ADS8361IRHBRG4
Dual, 500kSPS, 16-Bit, 2 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
TI
ADS8361IRHBT
Dual, 500kSPS, 16-Bit, 2 + 2 Channel, Simultaneous Sampling ANALOG-TO-DIGITAL CONVERTER
BB
©2020 ICPDF网 联系我们和版权申明