AFE1103E [TI]
HDSL/MDSL Analog Front End 48-SSOP;型号: | AFE1103E |
厂家: | TEXAS INSTRUMENTS |
描述: | HDSL/MDSL Analog Front End 48-SSOP 电信 光电二极管 电信集成电路 |
文件: | 总14页 (文件大小:337K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
®
AFE1103
AFE1103
HDSL/MDSL ANALOG FRONT END
FEATURES
DESCRIPTION
● COMPLETE ANALOG INTERFACE
● T1, E1, AND MDSL OPERATION
● CLOCK SCALEABLE SPEED
● SINGLE CHIP SOLUTION
Burr-Brown’s Analog Front End greatly reduces the
size and cost of an HDSL or MDSL system by provid-
ing all of the active analog circuitry needed to connect
the Brooktree Bt8952 HDSL digital signal processor
to an external compromise hybrid and a 1:2 HDSL line
transformer. All internal filter responses as well as the
pulse former output scale with clock frequency—
allowing the AFE1103 to operate over a range of bit
rates from 196kbps to 1.168Mbps.
● +5V ONLY (5V OR 3.3V DIGITAL)
● 250mW POWER DISSIPATION
● 48-PIN SSOP
● –40°C TO +85°C OPERATION
Functionally, this unit is separated into a transmit and
a receive section. The transmit section generates, fil-
ters, and buffers outgoing 2B1Q data. The receive
section filters and digitizes the symbol data received
on the telephone line and passes it to the Bt8952. The
HDSL Analog Interface is a monolithic device fabri-
cated on 0.6µCMOS. It operates on a single +5V
supply. It is housed in a 48-pin SSOP package. This
unit is second sourced by Brooktree’s Bt8921.
● SECOND SOURCED BY BROOKTREE
Bt8921
txLINEP
Pulse
Line
Former
Driver
txLINEN
REFP
PLLOUT
PLLIN
Voltage
Reference
VCM
Transmit
Control
txDATP
txDATN
txCLK
REFN
rxSYNC
rxLOOP
rxGAIN
Receive
Control
rxLINEP
2
rxLINEN
Delta-Sigma
Modulator
rxHYBP
rxHYBN
14
Decimation
Filter
rxD13 - rxD0
Patents Pending
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
©1996 Burr-Brown Corporation
PDS-1330A
Printed in U.S.A. August, 1996
SBWS001
SPECIFICATIONS
Typical at 25°C, AVDD = +5V, DVDD = +3.3V, ftx = 584kHz (E1 rate), unless otherwise specified.
AFE1103E
TYP
PARAMETER
COMMENTS
MIN
MAX
UNITS
RECEIVE CHANNEL
Number of Inputs
Input Voltage Range
Common-Mode Voltage
Input Impedance
Differential
Balanced Differential(1)
1.5V CMV Recommended
All Inputs
2
±3.0
+1.5
V
V
See Typical Performance Curves
Input Capacitance
Input Gain Matching
Resolution
10
±2
pF
%
Bits
Line Input vs Hybrid Input
14
Programmable Gain
Settling Time for Gain Change
Four Gains: 0dB, 3.25dB, 6dB, and 9dB
0
9
dB
6
Symbol
Periods
%FSR(2)
Gain + Offset Error
Tested at Each Gain Range
5
Output Data Coding
Offset Binary
Output Data Rate, rxSYNC(3)
98
98
584
584
kHz
TRANSMIT CHANNEL
Transmit Symbol Rate, ftx
T1 Transmit –3dB Point
T1 Rate Power Spectral Density(4)
E1 Transmit –3dB Point
E1 Rate Power Spectral Density(4)
Transmit Power(4, 5)
kHz
kHz
Bellcore TA-NWT-3017 Compliant
ETSI RTR/TM-03036 Compliant
196
See Typical Performance Curves
292
See Typical Performance Curves
kHz
13
14
dBm
Pulse Output
See Typical Performance Curves
Common-Mode Voltage, VCM
Output Resistance(6)
AVDD/2
1
V
Ω
DC to 1MHz
TRANSCEIVER PERFORMANCE
Uncancelled Echo(7)
rxGAIN = 0dB, Loopback Enabled
rxGAIN = 0dB, Loopback Disabled
rxGAIN = 3.25dB, Loopback Disabled
rxGAIN = 6dB, Loopback Disabled
rxGAIN = 9dB, Loopback Disabled
–67
–67
–69
–71
–73
dB
dB
dB
dB
dB
DIGITAL INTERFACE(6)
Logic Levels
VIH
VIL
VOH
VOL
|IIH| < 10µA
|IIL| < 10µA
IOH = –20µA
IOL = 20µA
DVDD –1
–0.3
DVDD –0.5
DVDD +0.3
+0.8
V
V
V
V
+0.4
Transmit/Receive Channel Interface
ttx1
ttx2
txCLK Period
txCLK Pulse Width
1.7
ttx1/16
10.2
15ttx1/16
µs
ns
POWER
Analog Power Supply Voltage
Analog Power Supply Voltage
Digital Power Supply Voltage
Digital Power Supply Voltage
Power Dissipation(4, 5, 8)
Power Dissipation(4, 5, 8)
PSRR
Specification
Operating Range
Specification
Operating Range
DVDD = 3.3V
5
V
V
V
4.75
3.15
5.25
5.25
3.3
V
250
300
mW
mW
dB
DVDD = 5V
60
TEMPERATURE RANGE
Operating(6)
–40
+85
°C
NOTES: (1) With a balanced differential signal, the positive input is 180° out of phase with the negative input, therefore the actual voltage swing about the common
mode voltage on each pin is ±1.5V to achieve a differential input range of ±3.0V or 6Vp-p. (2) FSR is Full-Scale Range. (3) The output data is available at twice the
symbol rate with interpolated values. (4) With a pseudo-random equiprobable sequence of HDSL pulses; 13.5dBm applied to the transformer (27dBm output from
txLINEP and txLINEN). (5) See the Discussion of Specifications section of this data sheet for more information. (6) Guaranteed by design and characterization. (7)
Uncancelled Echo is a measure of the total analog errors in the transmitter and receiver sections including the effect of non-linearity and noise. See the Discussion
of Specifications section of this data sheet for more information. (8) Power dissipation includes only the power dissipated within the component and does not include
power dissipated in the external loads. See the Discussion of Specifications section for more information.
®
AFE1103
2
PIN DESCRIPTIONS
PIN #
TYPE
NAME
DESCRIPTION
1
2
3
4
5
6
7
8
Ground
Power
Input
Input
Input
PGND
PVDD
txCLK
txDATN
txDATP
rxD0
rxD1
rxD2
rxD3
rxD4
rxD5
DGND
DVDD
rxD6
rxD7
Analog Ground for PLL
Analog Supply (+5V) for PLL
Symbol Clock (QCLK from Bt8952) (392kHz for T1, 584kHz for E1)
XMITB Line from Bt8952
XMIT Line from Bt8952
ADC Output Bit-0 (RCV 2 from Bt8952)
ADC Output Bit-1 (RCV 3 from Bt8952)
ADC Output Bit-2 (RCV 4 from Bt8952)
ADC Output Bit-3 (RCV 5 from Bt8952)
ADC Output Bit-4 (RCV 6 from Bt8952)
ADC Output Bit-5 (RCV 7 from Bt8952)
Digital Ground
Output
Output
Output
Output
Output
Output
Ground
Power
Output
Output
Output
Output
Output
Output
Output
Output
Ground
Input
Input
Input
Input
Power
Input
Input
Input
Input
Ground
Ground
Output
Output
Output
Power
Ground
Output
Power
Output
Ground
NC
NC
NC
NC
Output
Input
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Digital Supply (+3.3V to +5V)
ADC Output Bit-6 (RCV 8 from Bt8952)
ADC Output Bit-7 (RCV 9 from Bt8952)
ADC Output Bit-8 (RCV 10 from Bt8952)
ADC Output Bit-9 (RCV 11 from Bt8952)
ADC Output Bit-10 (RCV 12 from Bt8952)
ADC Output Bit-11 (RCV 13 from Bt8952)
ADC Output Bit-12 (RCV 14 from Bt8952)
ADC Output Bit-13 (RCV 15 from Bt8952)
Digital Ground
ADC Sync Signal (RCVCLK from Bt8952) (392kHz for T1, 584kHz for E1)
Receive Gain Control Bit-0
Receive Gain Control Bit-1
Loopback Control Signal (loopback is enabled by positive signal)
Analog Supply (+5V)
Negative Input from Hybrid Network
Positive Input from Hybrid Network
Negative Line Input
Positive Line Input
Analog Ground
Analog Ground
Positive Reference Output, Nominally 3.5V
Common-Mode Voltage (buffered), Nominally 2.5V
Negative Reference Output, Nominally 1.5V
Analog Supply (+5V)
Analog Ground
Transmit Line Output Negative
Analog Supply (+5V)
rxD8
rxD9
rxD10
rxD11
rxD12
rxD13
DGND
rxSYNC
rxGAIN0
rxGAIN1
rxLOOP
AVDD
rxHYBN
rxHYBP
rxLINEN
rxLINEP
AGND
AGND
REFP
VCM
REFN
AVDD
AGND
txLINEN
AVDD
txLINEP
AGND
NC
Transmit Line Output Positive
Analog Ground
Connection to Ground Recommended
Connection to Ground Recommended
Connection to Ground Recommended
Connection to Ground Recommended
PLL Filter Output
NC
NC
NC
PLLOUT
PLLIN
PLL Filter Input
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN
assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject
to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not
authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.
®
3
AFE1103
PIN CONFIGURATION
ABSOLUTE MAXIMUM RATINGS
Analog Inputs: Current .............................................. ±100mA, Momentary
±10mA, Continuous
Top View
SSOP
Voltage .................................. AGND –0.3V to AVDD +0.3V
Analog Outputs Short Circuit to Ground (+25°C) ..................... Continuous
AVDD to AGND ........................................................................ –0.3V to 6V
PVDD to PGND ........................................................................ –0.3V to 6V
DVDD to DGND ........................................................................ –0.3V to 6V
PLLIN or PLLOUT to PGND ......................................... –0.3V to PVDD +0.3V
Digital Input Voltage to DGND ..................................–0.3V to DVDD +0.3V
Digital Output Voltage to DGND ...............................–0.3V to DVDD +0.3V
AGND, DGND, PGND Differential Voltage ......................................... 0.3V
Junction Temperature (TJ) ............................................................ +150°C
Storage Temperature Range .......................................... –40°C to +125°C
Lead Temperature (soldering, 3s) ................................................. +260°C
Power Dissipation ......................................................................... 700mW
PGND
PVDD
txCLK
txDATN
txDATP
rxD0
1
2
3
4
5
6
7
8
9
48 PLLIN
47 PLLOUT
46 NC
45 NC
44 NC
43 NC
rxD1
42 AGND
41 txLINEP
40 AVDD
39 txLINEN
38 AGND
37 AVDD
36 REFN
35 VCM
rxD2
PACKAGE/ORDERING INFORMATION
rxD3
PACKAGE
DRAWING TEMPERATURE
rxD4 10
rxD5 11
PRODUCT
PACKAGE
NUMBER(1)
RANGE
AFE1103E
48-Pin Plastic SSOP
333
–40°C to +85°C
DGND 12
DVDD 13
rxD6 14
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix C of Burr-Brown IC Data Book.
AFE1103E
rxD7 15
34 REFP
33 AGND
32 AGND
31 rxLINEP
30 rxLINEN
29 rxHYBP
28 rxHYBN
27 AVDD
26 rxLOOP
25 rxGAIN1
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
rxD8 16
rxD9 17
rxD10 18
rxD11 19
rxD12 20
rxD13 21
DGND 22
rxSYNC 23
rxGAIN0 24
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
®
AFE1103
4
TYPICAL PERFORMANCE CURVES
At Output of Pulse Transformer
Typical at 25°C, AVDD = +5V, DVDD = +3.3V, unless otherwise specified.
POWER SPECTRAL DENSITY LIMIT
–20
–40
–38dBm/Hz for T1
–80dB/decade
T1
–40dBm/Hz for E1
E1
–60
–118dBm/Hz
–80
196kHz
292kHz
–120dBm/Hz
for E1
–100
–120
1K
10K
100K
1M
10M
Frequency (Hz)
CURVE 1. Upper Bound of Power Spectral Density Measured at the Transformer Output.
0.4T 0.4T
B = 1.07
C = 1.00
D = 0.93
QUATERNARY SYMBOLS
NORMALIZED
LEVEL
+3
+1
–1
–3
A
B
C
D
E
F
0.01
1.07
1.00
0.93
0.03
–0.01
–0.16
–0.05
0.0264
2.8248
2.6400
2.4552
0.0792
–0.0264
–0.4224
–0.1320
0.0088
0.9416
0.8800
0.8184
0.0264
–0.0088
–0.1408
–0.0440
–0.0088
–0.9416
–0.8800
–0.8184
–0.0264
0.0088
–0.0264
–2.8248
–2.6400
–2.4552
–0.0792
0.0264
G
H
0.1408
0.0440
0.4224
0.1320
1.25T
A = 0.01
E = 0.03
A = 0.01
F = –0.01
–1.2T
H = –0.05
14T
F = –0.01
50T
G = –0.16
–0.6T 0.5T
CURVE 2. Transmitted Pulse Template and Actual Performance as Measured at the Transformer Output.
INPUT IMPEDANCE vs BIT RATE
200
T1 = 784kbps, 45kΩ
E1 = 1168kbps, 30kΩ
150
100
T1
50
E1
0
100
300
500
700
900
1100
1300
Bit Rate (kbps)
CURVE 3. Input Impedance of rxLINE and rxHYB.
®
5
AFE1103
rxLOOP INPUT
THEORY OF OPERATION
rxLOOP is the loopback control signal. When enabled, the
rxLINEP and rxLINEN inputs are disconnected from the
AFE. The rxHYBP and rxHYBN inputs remain connected.
Loopback is enabled by applying a positive signal (Logic 1)
to rxLOOP.
The transmit channel consists of a switched-capacitor pulse
forming network followed by a differential line driver. The
pulse forming network receives symbol data from the XMIT
and XMITB outputs of the Bt8952 and generates a 2B1Q
output waveform. The output meets the pulse mask and
power spectral density requirements defined in European
Telecommunications Standards Institute document RTR/
TM-03036 for E1 mode and in sections 6.2.1 and 6.2.2.1 of
Bellcore technical advisory TA-NWT-001210 for T1 mode.
The differential line driver uses a composite output stage
combining class B operation (for high efficiency driving
large signals) with class AB operation (to minimize cross-
over distortion).
ECHO CANCELLATION IN THE AFE
The rxHYB input is designed to be subtracted from the
rxLINE input for first order echo cancellation. To accom-
plish this, note that the rxLINE input is connected to the
same polarity signal at the transformer (positive to positive
and negative to negative) while the rxHYB input is con-
nected to opposite polarity through the compromise hybrid
(negative to positive and positive to negative) as shown in
Figure 2.
The receive channel is designed around a fourth-order delta
sigma A/D converter. It includes a difference amplifier
designed to be used with an external compromise hybrid for
first order analog crosstalk reduction. A programmable gain
amplifier with gains of 0dB to +9dB is also included. The
delta sigma modulator operating at a 24X oversampling ratio
produces 14 bits of resolution at output rates up to 584kHz.
The basic functionality of the AFE1103 is illustrated in
Figure 1 shown below.
RECEIVE DATA CODING
The data from the receive channel A/D converter is coded in
offset binary.
ANALOG INPUT
OUTPUT CODE (rxD13 - rxD0)
Positive Full Scale
Negative Full Scale
11111111111111
00000000000000
The receive channel operates by summing the two differen-
tial inputs, one from the line (rxLINE) and the other from the
compromise hybrid (rxHYB). The connection of these two
inputs so that the hybrid signal is subtracted from the line
signal is described in the paragraph titled “Echo Cancella-
tion in the AFE”. The equivalent gain for each input in the
difference amp is 1. The resulting signal then passes to a
programmable gain amplifier which can be set for gains of
0dB through 9dB. The ADC converts the signal to a
14-bit digital word, rxD13-rxD0.
RECEIVE CHANNEL PROGRAMMABLE
GAIN AMPLIFIER
The gain of the amplifier at the input of the Receive Channel
is set by two gain control pins, rxGAIN1 and rxGAIN0. The
resulting gain between 0dB and +9dB is shown below.
rxGAIN1
rxGAIN0
GAIN
0dB
0
0
1
1
0
1
0
1
3.25dB
6dB
9dB
txDATP
txLINEP
txLINEN
Pulse Former
txDATN
Differential
Line Driver
rxHYBP
rxHYBN
14
ADC
rxD13 - rxD0
rxLINEP
rxLINEN
Programmable
Gain Amp
Difference
Amplifier
FIGURE 1. Functional Block Diagram of AFE1103.
®
AFE1103
6
0.1µF
0.1µF
0.1µF
PLLOUT
PLLIN
REFP
VCM
REFN
1kΩ
1:2 Transformer
Tip
13Ω
txLINEP
txLINEN
DVDD
0.01µF
200Ω
13Ω
Ring
0.1µF
8kΩ
8kΩ
Neg
Pos
Bt8952
XMIT
0.01µF
Compromise
Hybrid
txDATP
XMITB
QCLK
txDATN
Neg
Pos
txCLK
RCVCLK
rxSYNC
rxLOOP
rxGAIN1
rxGAIN0
rxD13 - rxD0
750Ω
0.1µF
2kΩ
rxHYBP
rxHYBN
AGAIN1
AGAIN0
AFE1103
100pF
750Ω
REFN
2kΩ
0.1µF
RCV15 - RCV2
14
Input anti-alias
filter fC 1MHz
0.1µF
PGND
DGND
AGND
AGND
AGND
AGND
rxLINEN
rxLINEP
2kΩ
750Ω
REFN
2kΩ
100pF
0.1µF
750Ω
DVDD
PVDD
AVDD AVDD AVDD
5V to 3.3V Digital
0.1µF
5V Analog
1 - 10µF
0.1µF 0.1µF 0.1µF
10µF
0.1µF
+
5 - 10Ω resistor for isolation
FIGURE 2. Basic Connection Diagram.
rxHYB AND rxLINE INPUT ANTI-ALIASING FILTERS
rxHYB AND rxLINE INPUT BIAS VOLTAGE
The –3dB frequency of the input anti-aliasing filter for the
rxLINE and rxHYB differential inputs should be about
1MHz. Suggested values for the filter are 750Ω for each of
the two input resistors and 100pF for the capacitor. Together
the two 750Ω resistors and the 100pF capacitor result in
–3dB frequency of just over 1MHz. The 750Ω input resis-
tors will result in a minimal voltage divider loss with the
input impedance of the AFE1103.
The transmitter output on the txLINE pins is centered at
midscale, 2.5V. But, the rxLINE input signal is centered at
1.5V in the circuit shown in Figure 2 above.
Inside the AFE1103, the rxHYB and rxLINE signals are
subtracted as described in the paragraph on echo cancella-
tion above. This means that the rxHYB inputs need to be
centered at 1.5V just as the rxLINE signal is centered at
1.5V. REFN (Pin 36) is a 1.5V voltage source. The external
compromise hybrid must be designed so that the signal into
the rxHYB inputs is centered at 1.5V.
This circuit applies at both T1 and E1 rates. For slower rates,
the antialiasing filters will give best performance with their
–3dB frequency approximately equal to the bit rate. For
example, a –3dB frequency of 500kHz should be used for a
single pair bit rate of 500kbps.
®
7
AFE1103
TIMING DIAGRAM
Transmit Timing
ttx1
ttx2
txCLK
txDATP (+3 Symbol)
txDATP (+1 Symbol)
txDATP (–1 Symbol)
txDATP (–3 Symbol)
ttx1/4
ttx1/2
3ttx1/4
ttx1/16 min
Receive Timing
nttx1/16
rxSYNC
nttx1/16 + 3ttx1/96
nttx1/16 + 51ttx1/96
Data 1
Data 1a
Data 2
rxD13 - rxD0
10ns
10ns
10ns
10ns
NOTES: (1) Any transmit sequence not shown will result in a zero symbol. (2) All transitions are specified relative to the rising edge of
txCLK. (3) Maximum allowable error for any txDAT edge is ±ttx1/12 (±17.8ns at E1 rate; ±26.6ns at T1 rate). (4) txDATN is the inverse of
txDATP. (5) Both txDAT inputs are read by the AFE1103 at 1/8, 3/8, and 5/8 of a symbol period from the rising edge of txCLK. (6)
rxSYNC can shift to one of 16 discrete delay times from the rising edge of txCLK. (7) It is recommended that rxD13 - rxD0 be read on
the rising edge of rxSYNC.
FIGURE 3. Timing Diagram.
RECEIVE TIMING
The bandwidth of the A/D converter decimation filter is
equal to one half of the symbol rate. The A/D converter data
output rate is 2X the symbol rate. The specifications of the
AFE1103 assume that one A/D converter output is used per
symbol period and the other interpolated output is ignored.
The Receive Timing Diagram above suggests using the
rxSYNC pulse to read the first data output in a symbol
period. Either data output may be used. Both data outputs
may be used for more flexible post-processing.
The rxSYNC signal controls portions of the A/D converter’s
decimation filter and the data output timing of the A/D
converter. It is generated at the symbol rate by the user and
must be synchronized with txCLK. The leading edge of
rxSYNC can occur at the leading edge of txCLK or it can be
shifted by the user in increments of 1/16 of a symbol period
to one of 15 discrete delay times after the leading edge of
txCLK.
®
AFE1103
8
tion in the digital circuitry does decrease with lower clock
frequency. In addition, the power dissipation in the digital
section is decreased when operating from a smaller supply
voltage, such as 3.3V. (The analog supply, AVDD, must
remain in the range 4.75V to 5.25V.)
DISCUSSION OF
SPECIFICATIONS
UNCANCELLED ECHO
The key measure of transceiver performance is uncancelled
echo. This measurement is made as shown in the diagram of
Figure 4. The AFE is connected to an output circuit includ-
ing a typical 1:2 line transformer. The line is simulated by a
135Ω resistor. Symbol sequences are generated by the tester
and applied both to the AFE and to the input of an adaptive
filter. The output of the adaptive filter is subtracted from the
AFE output to form the uncancelled echo signal. Once the
filter taps have converged, the RMS value of the uncancelled
echo is calculated. Since there is no far-end signal source or
additive line noise, the uncancelled echo contains only noise
and linearity errors generated in the transmitter and receiver.
The power dissipation listed in the specifications section
applies under these normal operating conditions: 5V Analog
Power Supply; 3.3V Digital Power Supply; standard 13.5dBm
delivered to the line; and a pseudo-random equiprobable
sequence of HDSL output pulses. The power dissipation
specifications includes all power dissipated in the AFE1103,
it does not include power dissipated in the external load.
The external power is 16.5dBm, 13.5dBm to the line and
13.5dBm to the impedance matching resistors. The external
load power of 16.5dBm is 45mW. The typical power dissi-
pation in the AFE1103 under various conditions is shown in
Table I.
The data sheet value for uncancelled echo is the ratio of the
RMS uncancelled echo (referred to the receiver input through
the receiver gain) to the nominal transmitted signal (13.5dBm
into 135Ω, or 1.74Vrms). This echo value is measured under
a variety of conditions: with loopback enabled (line input
disconnected); with loopback disabled under all receiver
gain ranges; and with the line shorted (S1 closed in Figure 4).
TYPICAL POWER
BIT RATE
PER AFE1103
(Symbols/sec)
DISSIPATION
IN THE AFE1103
(mW)
DVDD
(V)
584 (E1)
584 (E1)
392 (T1)
392 (T1)
146 (E1/4)
146 (E1/4)
3.3
5
3.3
5
3.3
5
250
300
240
270
230
245
POWER DISSIPATION
Approximately 75% of the power dissipation in the AFE1103
is in the analog circuitry, and this component does not
change with clock frequency. However, the power dissipa-
TABLE I. Typical Power Dissipation.
13Ω
13Ω
1:2
5.6Ω
5.6Ω
Transmit
Data
txDATP
txLINEP
txLINEN
135Ω
S1
0.047µF
576Ω
rxHYBP
1.54kΩ
2kΩ
100pF
AFE1103
0.01µF
150Ω
2kΩ
rxHYBN
576Ω
0.047µF
0.1µF
750Ω
rxLINEP
2kΩ
100pF
2kΩ
rxLINEN
REFN
750Ω
0.1µF
Uncanceled
Echo
rxD13 - rxD0
FIGURE 4. Uncancelled Echo Test Diagram.
®
9
AFE1103
In most systems, it will be natural to derive PVDD from the
AVDD supply. A 5Ω to 10Ω resistor should be used to
connect PVDD to the analog supply. This resistor in combi-
nation with the 10µF capacitor form a lowpass filter—
keeping glitches on AVDD from affecting PVDD. Ideally,
PVDD would originate from the analog supply (via the
resistor) near the power connector for the printed circuit
board. Likewise, PGND should connect to a large PCB trace
or small ground plane which returns to the power supply
connector underneath the PVDD supply path. The PGND
“ground plane” should also extend underneath PLLIN and
PLLOUT (pins 47 and 48).
LAYOUT
The analog front end of an HDSL system has a number of
conflicting requirements. It must accept and deliver digital
outputs at fairly high rates of speed, phase-lock to a high-
speed digital clock, and convert the line input to a high-
precision (14-bit) digital output. Thus, there are really three
sections of the AFE1103: the digital section, the phase-
locked loop, and the analog section.
The power supply for the digital section of the AFE1103 can
range from 3.3V to 5V. This supply should be decoupled to
digital ground with a ceramic 0.1µF capacitor placed as
close to DGND (pin 12) and DVDD (pin 13) as possible.
Ideally, both a digital power supply plane and a digital
ground plane should run up to and underneath the digital
pins of the AFE11103 (pins 3 through 26). However, DVDD
may be supplied by a wide printed circuit board (PCB) trace.
A digital ground plane underneath all digital pins is strongly
recommended.
The remaining portion of the AFE1103 should be considered
analog. All AGND pins should be connected directly to a
common analog ground plane and all AVDD pins should be
connected to an analog 5V power plane. Both of these planes
should have a low impedance path to the power supply.
Ideally, all ground planes and traces and all power planes
and traces should return to the power supply connector
before being connected together (if necessary). Each ground
and power pair should be routed over each other, should not
overlap any portion of another pair, and the pairs should be
separated by a distance of at least 0.25 inch (6mm). One
exception is that the digital and analog ground planes should
be connected together underneath the AFE1103 by a small
trace.
The phase-locked loop is powered from PVDD (pin 2) and its
ground is referenced to PGND (pin 1). Note that PVDD must
be in the 4.75V to 5.25V range. This portion of the AFE1103
should be decoupled with both a 10µF Tantalum capacitor
and a 0.1µF ceramic capacitor. The ceramic capacitor should
be placed as close to the AFE1103 as possible. The place-
ment of the Tantalum capacitor is not as critical, but should
be close. In each case, the capacitor should be connected
between PVDD and PGND.
®
AFE1103
10
PACKAGE OPTION ADDENDUM
www.ti.com
16-Jul-2010
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
AFE1103E
AFE1103E/1K
AFE1103E/1KG4
AFE1103EG4
NRND
ACTIVE
ACTIVE
NRND
SSOP
SSOP
SSOP
SSOP
DL
DL
DL
DL
48
48
48
48
25
1000
1000
25
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Samples Not Available
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
Purchase Samples
Samples Not Available
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) W1 (mm)
(mm) (mm) Quadrant
AFE1103E/1K
SSOP
DL
48
1000
330.0
32.4
11.35
16.2
3.1
16.0
32.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SSOP DL 48
SPQ
Length (mm) Width (mm) Height (mm)
346.0 346.0 49.0
AFE1103E/1K
1000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
Automotive
www.ti.com/automotive
www.ti.com/communications
Communications and
Telecom
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Consumer Electronics
Energy
www.ti.com/consumer-apps
www.ti.com/energy
Logic
Industrial
www.ti.com/industrial
Power Mgmt
Microcontrollers
RFID
power.ti.com
Medical
www.ti.com/medical
microcontroller.ti.com
www.ti-rfid.com
Security
www.ti.com/security
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
相关型号:
AFE1103E/1KG4
IC DATACOM, DIGITAL SLIC, PDSO48, GREEN, PLASTIC, SSOP-48, Digital Transmission Interface
TI
©2020 ICPDF网 联系我们和版权申明