BQ20Z65-R1DBTR [TI]
SBS 1.1-COMPLIANT GAS GAUGE AND PROTECTION ENABLED WITH IMPEDANCE TRACK™; SBS 1.1的电量监测计和保护已启用采用Impedance Track ™型号: | BQ20Z65-R1DBTR |
厂家: | TEXAS INSTRUMENTS |
描述: | SBS 1.1-COMPLIANT GAS GAUGE AND PROTECTION ENABLED WITH IMPEDANCE TRACK™ |
文件: | 总23页 (文件大小:347K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
SBS 1.1-COMPLIANT GAS GAUGE AND PROTECTION
ENABLED WITH IMPEDANCE TRACK™
Check for Samples: bq20z65-R1
1
FEATURES
APPLICATIONS
•
•
•
Notebook PCs
Medical and Test Equipment
Portable Instrumentation
2
•
Next Generation Patented Impedance Track™
Technology Accurately Measures Available
Charge in Li-Ion and Li-Polymer Batteries
–
Better Than 1% Error Over the Lifetime of
the Battery
DESCRIPTION
•
•
•
•
Supports the Smart Battery Specification
SBS V1.1
The bq20z65-R1 SBS-compliant gas gauge and
protection IC, incorporating patented Impedance
Track™ technology, is a single IC solution designed
for battery-pack or in-system installation. The
bq20z65-R1 measures and maintains an accurate
record of available charge in Li-ion or Li-polymer
batteries using its integrated high-performance
analog peripherals. The bq20z65-R1 monitors
capacity change, battery impedance, open-circuit
voltage, and other critical parameters of the battery
pack which reports the information to the system host
controller over a serial-communication bus. Together
with the integrated analog front-end (AFE)
short-circuit and overload protection, the bq20z65-R1
maximizes functionality and safety while minimizing
external component count, cost, and size in smart
battery circuits.
Flexible Configuration for 2 to 4 Series Li-Ion
and Li-Polymer Cells
Powerful 8-Bit RISC CPU With Ultralow Power
Modes
Full Array of Programmable Protection
Features
–
Voltage, Current, and Temperature
•
•
Satisfies JEITA Guidelines
Added Flexibility to Handle More Complex
Charging Profiles
•
•
Lifetime Data Logging
Drives 3, 4, and 5 Segment LED Display for
Battery-Pack Conditions
The implemented Impedance Track™ gas gauging
technology continuously analyzes the battery
impedance, resulting in superior gas-gauging
accuracy. This enables remaining capacity to be
calculated with discharge rate, temperature, and cell
aging all accounted for during each stage of every
cycle with high accuracy.
•
•
Supports SHA-1 Authentication
Complete Battery Protection and Gas Gauge
Solution in One Package
•
Available in a 44-Pin TSSOP (DBT) package
Table 1. AVAILABLE OPTIONS
PACKAGE(1)
TA
44-PIN TSSOP (DBT) Tube
44-PIN TSSOP (DBT) Tape and Reel
–40°C to 85°C
bq20z65-R1DBT(2)
bq20z65-R1DBTR(3)
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
(2) A single tube quantity is 40 units.
(3) A single reel quantity is 2000 units
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
Impedance Track is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
SYSTEM PARTITIONING DIAGRAM
PACK+
RBI
DISP
PreCharge FET
& GPOD Drive
N Channel FET
Drive
Power Mode
Control
Fuse Blow
Detection & Logic
LED Display
Oscillator
MSRT
RESET
SMBD
SMBC
SMB 1.1
System Control
AFE HW Control
Watchdog
ALERT
VCELL+
Voltage
Measurement
Cell Voltage
Multiplexer
+
Data Flash
Memory
VDD
OUT
CD
VC1
VC2
VC3
VC4
VC1
VC2
VC3
VC4
+
+
GND
Over
Temperature
Protection
Over & Under
Voltage
Protection
Impedance
Track™ Gas
Gauging
JEITA and
Enhanced
Charging
Algorithm
Cell Balancing
+
bq294xx
VC5
REG33
REG25
HW Over
Current & Short
Circuit Protection
SHA-1
Authentication
Temperature
Measurement
Over Current
Protection
Coulomb
Counter
Regulators
bq20z65-R1
RSNS
5mΩ - 20m Ω typ
PACK-
PACKAGE THERMAL DATA
Table 2.
T
A ≤ 25°C
DERATING FACTOR
TA > 25°C
TA = 70°C
POWER RATING
TA = 85°
POWER RATING
DEVICE
PACKAGE
θja
POWER RATING
bq20z65-R1
TSSOP-44
47.6°C/W
2101mW
21.01mw/°C
1155mW
840mW
2
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
PACKAGE PINOUT DIAGRAM
bq20z65-R1
DBT PACKAGE
(TOP VIEW)
DSG
PACK
VCC
1
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
CHG
BAT
2
3
VC1
ZVCHG
GPOD
PMS
4
VC2
VC3
5
6
VC4
VSS
7
VC5
REG33
TOUT
VCELL+
8
ASRP
ASRN
RESET
VSS
9
10
11
12
13
14
15
16
17
18
19
20
21
22
ALERT
NC
RBI
REG25
VSS
TS1
TS2
MRST
GSRN
GSRP
LED5
LED4
LED3
LED2
LED1
PRES
PFIN
SAFE
SMBD
NC
SMBC
DISP
VSS
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
TERMINAL FUNCTIONS
TERMINAL
I/O(1)
DESCRIPTION
NO.
NAME
1
DSG
O
High side N-chan discharge FET gate drive
Battery pack input voltage sense input. It also serves as device wake up when device is in shutdown
mode.
2
PACK
IA, P
Positive device supply input. Connect to the center connection of the CHG FET and DSG FET to
ensure device supply either from battery stack or battery pack input
3
4
5
VCC
P
O
ZVCHG
GPOD
P-chan pre-charge FET gate drive
High voltage general purpose open drain output. Can be configured to be used in pre-charge
condition
OD
Pre-charge mode setting input. Connect to PACK to enable 0v pre-charge using charge FET
connected at CHG pin. Connect to VSS to disable 0V pre-charge using charge FET connected at
CHG pin.
6
PMS
I
7
8
VSS
REG33
TOUT
P
P
P
-
Negative supply voltage input. Connect all VSS pins together for operation of device
3.3V regulator output. Connect at least a 2.2μF capacitor to REG33 and VSS
Thermistor bias supply output
9
10
VCELL+
Internal cell voltage multiplexer and amplifier output. Connect a 0.1μF capacitor to VCELL+ and VSS
Alert output. In case of short circuit condition, overload condition and watchdog time out this pin will
be triggered.
11
ALERT
OD
12
13
14
15
NC
TS1
-
IA
IA
I
Not used - leave floating
1st Thermistor voltage input connection to monitor temperature
2nd Thermistor voltage input connection to monitor temperature
Active low input to sense system insertion. Typically requires additional ESD protection.
TS2
PRES
Active low input to detect secondary protector status, and to allow the bq20z65-R1 to report the
status of the 2nd level protection input.
16
17
18
19
20
PFIN
SAFE
SMBD
NC
I
OD
I/OD
-
Active high output to enforce additional level of safety protection; e.g., fuse blow.
SMBus data open-drain bidirectional pin used to transfer address and data to and from the
bq20z65-R1
Not used - leave floating
SMBus clock open-drain bidirectional pin used to clock the data transfer to and from the
bq20z65-R1
SMBC
I/OD
Display control for the LEDs. This pin is typically connected to VCC via a 100kΩ resistor and a push
button switch connected to VSS.
21
DISP
I
22
23
24
25
26
27
28
29
VSS
LED1
LED2
LED3
LED4
LED5
GSRP
GSRN
P
I
Negative supply voltage input. Connect all VSS pins together for operation of device
LED1 display segment that drives an external LED depending on the firmware configuration
LED2 display segment that drives an external LED depending on the firmware configuration
LED3 display segment that drives an external LED depending on the firmware configuration
LED4 display segment that drives an external LED depending on the firmware configuration
LED5 display segment that drives an external LED depending on the firmware configuration
Coulomb counter differential input. Connect to one side of the sense resistor
I
I
I
I
IA
IA
Coulomb counter differential input. Connect to one side of the sense resistor
Master reset input that forces the device into reset when held low. Must be held high for normal
operation. Connect to RESET for correct operation of device
30
MRST
I
31
32
VSS
P
P
Negative supply voltage input. Connect all VSS pins together for operation of device
2.5V regulator output. Connect at least a 1mF capacitor to REG25 and VSS
REG25
RAM / Register backup input. Connect a capacitor to this pin and VSS to protect loss of RAM /
Register data in case of short circuit condition.
33
RBI
P
34
35
36
37
VSS
RESET
ASRN
ASRP
P
O
Negative supply voltage input. Connect all VSS pins together for operation of device
Reset output. Connect to MSRT.
IA
IA
Short circuit and overload detection differential input. Connect to sense resistor
Short circuit and overload detection differential input. Connect to sense resistor
(1) I = Input, IA = Analog input, I/O = Input/output, I/OD = Input/Open-drain output, O = Output, OA = Analog output, P = Power
Submit Documentation Feedback
4
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
TERMINAL FUNCTIONS (continued)
TERMINAL
I/O(1)
DESCRIPTION
NO.
NAME
Cell votage sense input and cell balancing input for the negative voltage of the bottom cell in cell
stack.
38
VC5
IA, P
IA, P
IA, P
Cell votage sense input and cell balancing input for the positive voltage of the bottom cell and the
negative voltage of the second lowest cell in cell stack.
39
40
VC4
VC3
Cell voltage sense input and cell balancing input for the positive voltage of the second lowest cell in
cell stack and the negative voltage of the second highest cell in 4 cell applications.
Cell voltage sense input and cell balancing input for the positive voltage of the second highest cell
41
42
VC2
VC1
IA, P and the negative voltage of the highest cell in 4 cell applications. Connect to VC3 in 2 cell stack
applications.
Cell voltage sense input and cell balancing input for the positive voltage of the highest cell in cell
IA, P
stack in 4 cell applications. Connect to VC2 in 3 or 2 cell stack applications.
43
44
BAT
I, P
O
Battery stack voltage sense input.
CHG
High side N-channel charge FET gate drive
ABSOLUTE MAXIMUM RATINGS
Over operating free-air temperature (unless otherwise noted)
(1)
PIN
UNIT
BAT, VCC
–0.3 V to 34 V
–0.3 V to 34 V
–0.3 V to 8.5 V
–0.3 V to 34 V
–0.3 V to 1 V
PACK, PMS
VSS
Supply voltage range
Input voltage range
VC(n)-VC(n+1); n = 1, 2, 3, 4
VC1, VC2, VC3, VC4
VC5
PFIN, SMBD, SMBC. LED1, LED2, LED3,
LED4, LED5, DISP
–0.3 V to 6 V
TS1, TS2, SAFE, VCELL+, PRES, ALERT
MRST, GSRN, GSRP, RBI
ASRN, ASRP
–0.3 V to V(REG25) + 0.3 V
–0.3 V to V(REG25) + 0.3 V
–1 V to 1 V
VIN
DSG, CHG, GPOD
ZVCHG
–0.3 V to 34 V
–0.3 V to V (BAT)
–0.3 V to 6 V
VOUT Output voltage range
TOUT, ALERT, REG33
RESET
–0.3 V to 7 V
REG25
–0.3 V to 2.75 V
PRES, PFIN, SMBD, SMBC, LED1, LED2,
LED3, LED4, LED5
ISS
Maximum combined sink current for input pins
50 mA
TA
Operating free-air temperature range
Functional temperature
–40°C to 85°C
–40°C to 100°C
–65°C to 150°C
TF
Tstg
Storage temperature range
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Over operating free-air temperature range (unless otherwise noted)
PIN
MIN NOM
MAX UNIT
VSS
Supply voltage
VCC, BAT
VCC, BAT, PACK
4.5
5.5
25
V
V
V(STARTUP)
Minimum startup voltage
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
RECOMMENDED OPERATING CONDITIONS (continued)
Over operating free-air temperature range (unless otherwise noted)
PIN
MIN NOM
MAX UNIT
VC(n)-VC(n+1); n = 1,2,3,4
VC1, VC2, VC3, VC4
0
0
5
VSS
0.5
0.5
25
V
V
VIN
Input voltage range
VC5
0
V
ASRN, ASRP
PACK, PMS
GPOD
–0.5
0
V
V
V(GPOD)
I(GPOD)
Output voltage range
Drain current(1)
0
25
V
GPOD
1
mA
µF
µF
µF
kΩ
C(REG25)
C(REG33)
C(VCELL+)
R(PACK)
2.5V LDO capacitor
REG25
REG33
VCELL+
PACK
1
2.2
0.1
1
3.3V LDO capacitor
Cell voltage output capacitor
PACK input block resistor(2)
(1) Use an external resistor to limit the current to GPOD to 1mA in high voltage application.
(2) Use an external resistor to limit the inrush current PACK pin required.
6
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
ELECTRICAL CHARACTERISTICS
Over operating free-air temperature range (unless otherwise noted), TA = –40°C to 85°C, V(REG25) = 2.41 V to 2.59 V,
V(BAT) = 14 V, C(REG25) = 1 µF, C(REG33) = 2.2 µF; typical values at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
I(NORMAL)
I(SLEEP)
Firmware running
Sleep mode
550
124
90
µA
µA
µA
µA
µA
CHG FET on; DSG FET on
CHG FET off; DSG FET on
CHG FET off; DSG FET off
52
I(SHUTDOWN)
Shutdown mode
0.1
1
1
SHUTDOWN WAKE; TA = 25°C (unless otherwise noted)
Shutdown exit at VSTARTUP
threshold
I(PACK)
µA
SRx WAKE FROM SLEEP; TA = 25°C (unless otherwise noted)
Positive or negative wake
threshold with 1.00 mV, 2.25 mV,
4.5 mV and 9 mV programmable
V(WAKE)
1.25
10
mV
options
V (WAKE) = 1 mV;
I(WAKE)= 0, RSNS1 = 0, RSNS0 = 1;
-0.7
-0.8
0.7
0.8
V(WAKE) = 2.25 mV;
I(WAKE) = 1, RSNS1 = 0, RSNS0 = 1;
I(WAKE) = 0, RSNS1 = 1, RSNS0 = 0;
V(WAKE_ACR) Accuracy of V(WAKE)
mV
V(WAKE) = 4.5 mV;
I(WAKE) = 1, RSNS1 = 1, RSNS0 = 1;
I(WAKE) = 0, RSNS1 = 1, RSNS0 = 0;
-1.0
-1.4
1.0
1.4
V(WAKE) = 9 mV;
I(WAKE) = 1, RSNS1 = 1, RSNS0 = 1;
Temperature drift of V(WAKE)
accuracy
V(WAKE_TCO)
t(WAKE)
0.5
1
%/°C
ms
Time from application of current
and wake of bq20z65-R1
10
WATCHDOG TIMER
tWDTINT Watchdog start up detect time
tWDWT Watchdog detect time
2.5V LDO; I(REG33OUT) = 0 mA; TA = 25°C (unless otherwise noted)
4.5 < VCC or BAT < 25 V;
250
50
500
100
1000
150
ms
µs
V(REG25)
Regulator output voltage
I(REG25OUT) ≤ 16 mA;
2.41
2.5
2.59
V
TA = –40°C to 100°C
ΔV(REG25TEM Regulator output change with
I(REG25OUT) = 2 mA;
TA = –40°C to 100°C
±0.2
3
%
temperature
P)
ΔV(REG25LINE
5.4 < VCC or BAT < 25 V;
I(REG25OUT) = 2 mA
Line regulation
10
mV
)
0.2 mA ≤ I(REG25OUT) ≤ 2 mA
0.2 mA ≤ I(REG25OUT) ≤ 16 mA
7
25
50
ΔV(REG25LOA
Load regulation
mV
mA
D)
25
drawing current until
REG25 = 2 V to 0 V
I(REG25MAX)
Current limit
5
3
40
75
3.3V LDO; I(REG25OUT) = 0 mA; TA = 25°C (unless otherwise noted)
4.5 < VCC or BAT < 25 V;
V(REG33)
Regulator output voltage
I(REG33OUT) ≤ 25 mA;
3.3
3.6
V
TA = –40°C to 100°C
ΔV(REG33TEM Regulator output change with
I(REG33OUT) = 2 mA;
TA = –40°C to 100°C
±0.2
3
%
temperature
P)
ΔV(REG33LINE
5.4 < VCC or BAT < 25 V;
I(REG33OUT) = 2 mA
Line regulation
10
mV
)
0.2 mA ≤ I(REG33OUT) ≤ 2 mA
7
40
17
100
145
65
ΔV(REG33LOA
Load regulation
mV
mA
D)
0.2mA ≤ I(REG33OUT) ≤ 25 mA
drawing current until REG33 = 3 V
short REG33 to VSS, REG33 = 0 V
25
12
100
I(REG33MAX)
Current limit
THERMISTOR DRIVE
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Over operating free-air temperature range (unless otherwise noted), TA = –40°C to 85°C, V(REG25) = 2.41 V to 2.59 V,
V(BAT) = 14 V, C(REG25) = 1 µF, C(REG33) = 2.2 µF; typical values at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
100
0.4
UNIT
V(TOUT)
RDS(on)
LED OUTPUTS
Output voltage
I(TOUT) = 0 mA; TA = 25°C
V(REG25)
V
I(TOUT) = 1 mA; RDS(on) = (V(REG25) - V(TOUT) )/ 1 mA; TA
–40°C to 100°C
=
TOUT pass element resistance
50
Ω
VOL
Output low voltage
LED1, LED2, LED3, LED4, LED5
V
VCELL+ HIGH VOLTAGE TRANSLATION
VC(n) - VC(n+1) = 0 V;
TA = –40°C to 100°C
0.950
0.275
0.965
0.975
0.3
1
0.375
0.985
V(VCELL+OUT)
VC(n) - VC(n+1) = 4.5 V;
TA = –40°C to 100°C
internal AFE reference voltage ;
TA = –40°C to 100°C
V(VCELL+REF) Translation output
0.975
V
V(VCELL+PACK
Voltage at PACK pin;
TA = –40°C to 100°C
0.98 ×
V(PACK)/18
1.02 ×
V(PACK)/18
V(PACK)/18
V(BAT)/18
)
Voltage at BAT pin;
TA = –40°C to 100°C
0.98 ×
V(BAT)/18
1.02 ×
V(BAT)/18
V(VCELL+BAT)
CMMR
Common mode rejection ratio
Cell scale factor
VCELL+
40
dB
K= {VCELL+ output (VC5=0V; VC4=4.5V) - VCELL+
output (VC5=0V; VC4=0V)}/4.5
0.147
0.150
0.150
18
0.153
0.153
K
K= {VCELL+ output (VC2=13.5V; VC1=18V) - VCELL+
output
(VC5=13.5V; VC1=13.5V)}/4.5
0.147
12
Drive Current to VCELL+
capacitor
VC(n) - VC(n+1) = 0V; VCELL+ = 0 V;
TA = –40°C to 100°C
I(VCELL+OUT)
μA
CELL output (VC2 = VC1 = 18 V) - CELL output (VC2 =
VC1 = 0 V)
V(VCELL+O)
IVCnL
CELL offset error
-18
-1
-1
18
1
mV
VC(n) pin leakage current
VC1, VC2, VC3, VC4, VC5 = 3 V
0.01
μA
CELL BALANCING
internal cell balancing FET
RDS(on) for internal FET switch at
VDS = 2 V; TA = 25°C
RBAL
200
400
600
Ω
resistance
HARDWARE SHORT CIRCUIT AND OVERLOAD PROTECTION; TA = 25°C (unless otherwise noted)
VOL = 25 mV (min)
15
90
25
100
35
110
225
70
OL detection threshold voltage
accuracy
V(OL)
VOL = 100 mV; RSNS = 0, 1
VOL = 205 mV (max)
mV
mV
mV
185
30
205
V(SCC) = 50 mV (min)
50
SCC detection threshold voltage
accuracy
V(SCC)
V(SCC) = 200 mV; RSNS = 0, 1
V(SCC) = 475 mV (max)
V(SCD) = –50 mV (min)
180
428
–30
–180
–428
200
220
523
–70
–220
–523
475
–50
SCD detection threshold voltage
accuracy
V(SCD)
V(SCD) = –200 mV; RSNS = 0, 1
V(SCD) = –475 mV (max)
–200
–475
±15.25
tda
tpd
Delay time accuracy
μs
μs
Protection circuit propagation
delay
50
FET DRIVE CIRCUIT; TA = 25°C (unless otherwise noted)
V(DSGON) = V(DSG) - V(PACK)
;
V(DSGON)
DSG pin output on voltage
V(GS) connected to 10 MΩ; DSG and CHG on;
TA = –40°C to 100°C
8
8
12
12
16
16
V
V
V(CHGON) = V(CHG) - V(BAT)
;
V(CHGON)
CHG pin output on voltage
V(GS) = 10 MΩ; DSG and CHG on;
TA = –40°C to 100°C
V(DSGOFF)
V(CHGOFF)
DSG pin output off voltage
CHG pin output off voltage
V(DSGOFF) = V(DSG) - V(PACK)
V(CHGOFF) = V(CHG) - V(BAT)
V(CHG): V(PACK) ≥ V(PACK) + 4V
V(DSG): V(BAT) ≥V(BAT) + 4V
0.2
0.2
V
V
400
400
1000
1000
tr
Rise time
CL= 4700 pF
μs
8
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
ELECTRICAL CHARACTERISTICS (continued)
Over operating free-air temperature range (unless otherwise noted), TA = –40°C to 85°C, V(REG25) = 2.41 V to 2.59 V,
V(BAT) = 14 V, C(REG25) = 1 µF, C(REG33) = 2.2 µF; typical values at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
μs
V(CHG): V(PACK) + V(CHGON) ≥ V(PACK)
1V
+
40
200
tf
Fall time
CL= 4700pF
BAT = 4.5 V
V(DSG): VC1 + V(DSGON) ≥ VC1 + 1 V
40
200
3.7
V(ZVCHG)
ZVCHG clamp voltage
3.3
3.5
V
LOGIC; TA = –40°C to 100°C (unless otherwise noted)
ALERT
60
1
100
3
200
6
R(PULLUP)
Internal pullup resistance
kΩ
RESET
ALERT
0.2
0.4
0.6
VOL
Logic low output voltage level
RESET; V(BAT) = 7V; V(REG25) = 1.5 V; I (RESET) = 200 μA
GPOD; I(GPOD) = 50 μA
V
LOGIC SMBC, SMBD, PFIN, PRES, SAFE, ALERT, DISP
VIH
VIL
High-level input voltage
Low-level input voltage
2.0
V
V
0.8
0.4
VREG25–0.
5
VOH
Output voltage high(1)
IL = –0.5 mA
V
VOL
Low-level output voltage
Input capacitance
PRES, PFIN, ALERT, DISP; IL = 7 mA;
V
CI
5
pF
mA
µA
µA
I(SAFE)
Ilkg(SAFE)
Ilkg
SAFE source currents
SAFE leakage current
Input leakage current
SAFE active, SAFE = V(REG25) –0.6 V
SAFE inactive
–3
–0.2
0.2
1
ADC(2)
Input voltage range
Conversion time
TS1, TS2, using Internal Vref
–0.2
1
V
31.5
15
ms
bits
bits
Resolution (no missing codes)
Effective resolution
Integral nonlinearity
Offset error(4)
16
14
±0.03 %FSR(3)
140
2.5
250
18
µV
Offset error drift(4)
TA = 25°C to 85°C
μV/°C
Full-scale error(5)
±0.1%
50
±0.7%
Full-scale error drift
Effective input resistance(6)
PPM/°C
8
–0.20
15
MΩ
COULOMB COUNTER
Input voltage range
0.20
±0.034
0.7
V
Conversion time
Single conversion
Single conversion
–0.1 V to 0.20 V
–0.20 V to –0.1 V
TA = 25°C to 85°C
250
ms
bits
Effective resolution
±0.007
±0.007
10
Integral nonlinearity
%FSR
(7)
Offset error
µV
Offset error drift
0.4
µV/°C
(9)
Full-scale error(8)
±0.35%
150
Full-scale error drift
PPM/°C
(1) RC[0:7] bus
(2) Unless otherwise specified, the specification limits are valid at all measurement speed modes.
(3) Full-scale reference
(4) Post-calibration performance and no I/O changes during conversion with SRN as the ground reference.
(5) Uncalibrated performance. This gain error can be eliminated with external calibration.
(6) The A/D input is a switched-capacitor input. Since the input is switched, the effective input resistance is a measure of the average
resistance.
(7) Post-calibration performance
(8) Reference voltage for the coulomb counter is typically Vref/3.969 at V(REG25) = 2.5 V, TA = 25°C.
(9) Uncalibrated performance. This gain error can be eliminated with external calibration.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Over operating free-air temperature range (unless otherwise noted), TA = –40°C to 85°C, V(REG25) = 2.41 V to 2.59 V,
V(BAT) = 14 V, C(REG25) = 1 µF, C(REG33) = 2.2 µF; typical values at TA = 25°C (unless otherwise noted)
PARAMETER
Effective input resistance(10)
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TA = 25°C to 85°C
2.5
MΩ
INTERNAL TEMPERATURE SENSOR
V(TEMP)
VOLTAGE REFERENCE
Output voltage
Temperature sensor voltage(11)
-2.0
mV/°C
1.215
1.225
65
1.230
V
Output voltage drift
PPM/°C
HIGH FREQUENCY OSCILLATOR
f(OSC)
Operating frequency
4.194
0.25%
0.25%
2.5
MHz
–3%
–2%
3%
2%
5
(12) (13)
f(EIO)
Frequency error
Start-up time(14)
TA = 20°C to 70°C
t(SXO)
ms
LOW FREQUENCY OSCILLATOR
f(LOSC)
f(LEIO)
t(LSXO)
Operating frequency
32.768
0.25%
0.25%
kHz
–2.5%
–1.5%
2.5%
1.5%
500
Frequency error(13)
Start-up time(14)
(15)
TA = 20°C to 70°C
µs
(10) The CC input is a switched capacitor input. Since the input is switched, the effective input resistance is a measure of the average
resistance.
(11) –53.7 LSB/°C
(12) The frequency error is measured from 4.194 MHz.
(13) The frequency drift is included and measured from the trimmed frequency at V(REG25) = 2.5V, TA = 25°C.
(14) The startup time is defined as the time it takes for the oscillator output frequency to be ±3%.
(15) The frequency error is measured from 32.768 kHz.
10
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
POWER-ON RESET
Over operating free-air temperature range (unless otherwise noted), TA = –40°C to 85°C, V(REG25) = 2.41 V to 2.59 V,
V(BAT) = 14 V, C(REG25) = 1 µF, C(REG33) = 2.2 µF; typical values at TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
1.7
5
TYP
1.8
MAX
1.9
UNIT
V
VIT-
Negative-going voltage input
Power-on reset hysteresis
VHYS
125
200
mV
active low time after power up or watchdog
reset
tRST
RESET active low time
100
250
560
µs
POWER ON RESET BEHAVIOR
VS
FREE-AIR TEMPERATURE
1.81
1.8
1.79
1.78
1.77
1.76
-40
-20
0
20
40
60
80
TA - Free-Air Temperature - °C
DATA FLASH CHARACTERISTICS OVER RECOMMENDED OPERATING TEMPERATURE AND
SUPPLY VOLTAGE
Typical values at TA = 25°C and V(REG25) = 2.5 V (unless otherwise noted)
PARAMETER
Data retention
Flash programming write-cycles
t(ROWPROG) Row programming time
TEST CONDITIONS
MIN TYP MAX
UNIT
Years
Cycles
ms
10
20k
2
(1)
See
t(MASSERASE) Mass-erase time
t(PAGEERASE) Page-erase time
200
20
ms
ms
I(DDPROG)
I(DDERASE)
RAM/REGISTER BACKUP
Flash-write supply current
5
5
10
10
mA
Flash-erase supply current
mA
V(RBI) > V(RBI)MIN , VREG25 < VIT–, TA = 85°C
V(RBI) > V(RBI)MIN , VREG25 < VIT–, TA = 25°C
1000 2500
90 220
I(RB)
RB data-retention input current
RB data-retention input voltage(1)
nA
V
V(RB)
1.7
(1) Specified by design. Not production tested.
SMBus TIMING CHARACTERISTICS
TA = –40°C to 85°C Typical Values at TA = 25°C and VREG25 = 2.5 V (Unless Otherwise Noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
f(SMB)
SMBus operating frequency
Slave mode, SMBC 50% duty cycle
10
100
kHz
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
SMBus TIMING CHARACTERISTICS (continued)
TA = –40°C to 85°C Typical Values at TA = 25°C and VREG25 = 2.5 V (Unless Otherwise Noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
f(MAS)
SMBus master clock frequency
Master mode, No clock low slave
extend
51.2
kHz
Bus free time between start and stop
(see Figure 1)
t(BUF)
4.7
µs
t(HD:STA)
t(SU:STA)
t(SU:STO)
t(HD:DAT)
Hold time after (repeated) start (see Figure 1)
Repeated start setup time (see Figure 1)
Stop setup time (see Figure 1)
4
4.7
4
µs
µs
µs
ns
Receive mode
Transmit mode
0
Data hold time (see Figure 1)
300
250
25
4.7
4
t(SU:DAT)
t(TIMEOUT)
t(LOW)
Data setup time (see Figure 1)
Error signal/detect (see Figure 1)
Clock low period (see Figure 1)
Clock high period (see Figure 1)
ns
µs
µs
µs
ms
(1)
See
35
(2)
t(HIGH)
See
50
25
(3)
t(LOW:SEXT) Cumulative clock low slave extend time
See
Cumulative clock low master extend time
(see Figure 1)
(4)
t(LOW:MEXT)
See
10
ms
(5)
tf
tr
Clock/data fall time
Clock/data rise time
See
300
ns
ns
(6)
See
1000
(1) The bq20z65-R1 times out when any clock low exceeds t(TIMEOUT)
.
(2) t(HIGH), Max, is the minimum bus idle time. SMBC = SMBD = 1 for t > 50 ms causes reset of any transaction involving bq20z65-R1 that
is in progress. This specification is valid when the NC_SMB control bit remains in the default cleared state (CLK[0]=0).
(3) t(LOW:SEXT) is the cumulative time a slave device is allowed to extend the clock cycles in one message from initial start to the stop.
(4) t(LOW:MEXT) is the cumulative time a master device is allowed to extend the clock cycles in one message from initial start to the stop.
(5) Rise time tr = VILMAX – 0.15) to (VIHMIN + 0.15)
(6) Fall time tf = 0.9VDD to (VILMAX – 0.15)
12
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
tR
tF
tF
tR
tSU(STO)
tHD(STA)
tBUF
tHIGH
SMBC
SMBC
SMBD
tLOW
SMBD
P
S
tHD(DAT)
tSU(DAT)
Start and Stop condition
Wait and Hold condition
tSU(STA)
tTIMEOUT
SMBC
SMBD
SMBC
SMBD
S
Timeout condition
Repeated Start condition
A. SCLKACK is the acknowledge-related clock pulse generated by the master.
Figure 1. SMBus Timing Diagram
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
FEATURE SET
Primary (1st Level) Safety Features
The bq20z65-R1 supports a wide range of battery and system protection features that can easily be configured.
The primary safety features include:
•
•
•
•
•
Cell over/undervoltage protection
Charge and discharge overcurrent
Short Circuit protection
Charge and discharge overtemperature with independent alarms and thresholds for each thermistor
AFE Watchdog
Secondary (2nd Level) Safety Features
The secondary safety features of the bq20z65-R1 can be used to indicate more serious faults via the SAFE pin.
This pin can be used to blow an in-line fuse to permanently disable the battery pack from charging or
discharging. The secondary safety protection features include:
•
•
•
•
•
•
•
•
•
•
•
Safety overvoltage
Safety undervoltage
2nd level protection IC input
Safety overcurrent in charge and discharge
Safety over-temperature in charge and discharge with independent alarms and thresholds for each thermistor
Charge FET and zero-volt charge FET fault
Discharge FET fault
Cell imbalance detection (active and at rest)
Open thermistor detection
Fuse blow detection
AFE communication fault
Charge Control Features
The bq20z65-R1 charge control features include:
•
•
•
•
Supports JEITA temperature ranges. Reports charging voltage and charging current according to the active
temperature range.
Handles more complex charging profiles. Allows for splitting the standard temperature range into 2
sub-ranges and allows for varying the charging current according to the cell voltage.
Reports the appropriate charging current needed for constant current charging and the appropriate charging
voltage needed for constant voltage charging to a smart charger using SMBus broadcasts.
Determines the chemical state of charge of each battery cell using Impedance Track™ and can reduce the
charge difference of the battery cells in fully charged state of the battery pack gradually using cell balancing
algorithm during charging. This prevents fully charged cells from overcharging and causing excessive
degradation and also increases the usable pack energy by preventing premature charge termination
•
•
•
Supports pre-charging/zero-volt charging
Supports charge inhibit and charge suspend if battery pack temperature is out of temperature range
Reports charging fault and also indicate charge status via charge and discharge alarms.
Gas Gauging
The bq20z65-R1 uses the Impedance Track™ Technology to measure and calculate the available charge in
battery cells. The achievable accuracy is better than 1% error over the lifetime of the battery and there is no full
charge discharge learning cycle required.
See Theory and Implementation of Impedance Track Battery Fuel-Gauging Algorithm application note (SLUA364)
for further details.
14
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
Lifetime Data Logging Features
The bq20z65-R1 offers lifetime data logging, where important measurements are stored for warranty and
analysis purposes. The data monitored include:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Lifetime maximum temperature
Lifetime maximum temperature count
Lifetime maximum temperature duration
Lifetime minimum temperature
Lifetime maximum battery cell voltage
Lifetime maximum battery cell voltage count
Lifetime maximum battery cell voltage duration
Lifetime minimum battery cell voltage
Lifetime maximum battery pack voltage
Lifetime minimum battery pack voltage
Lifetime maximum charge current
Lifetime maximum discharge current
Lifetime maximum charge power
Lifetime maximum discharge power
Lifetime maximum average discharge current
Lifetime maximum average discharge power
Lifetime average temperature
Authentication
The bq20z65-R1 supports authentication by the host using SHA-1.
Power Modes
The bq20z65-R1 supports 3 different power modes to reduce power consumption:
•
In Normal Mode, the bq20z65-R1 performs measurements, calculations, protection decisions and data
updates in 1 second intervals. Between these intervals, the bq20z65-R1 is in a reduced power stage.
•
In Sleep Mode, the bq20z65-R1 performs measurements, calculations, protection decisions and data update
in adjustable time intervals. Between these intervals, the bq20z65-R1 is in a reduced power stage. The
bq20z65-R1 has a wake function that enables exit from Sleep mode, when current flow or failure is detected.
•
In Shutdown Mode the bq20z65-R1 is completely disabled.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
CONFIGURATION
Oscillator Function
www.ti.com
The bq20z65-R1 fully integrates the system oscillators therefore, no external components are required for this
feature.
System Present Operation
The bq20z65-R1 periodically verifies the PRES pin and detects that the battery is present in the system via a low
state on a PRES input. When this occurs, the bq20z65-R1 enters normal operating mode. When the pack is
removed from the system and the PRES input is high, the bq20z65-R1 enters the battery-removed state,
disabling the charge, discharge, and ZVCHG FETs. The PRES input is ignored and can be left floating when
non-removal mode is set in the data flash.
BATTERY PARAMETER MEASUREMENTS
The bq20z65-R1 uses an integrating delta-sigma analog-to-digital converter (ADC) for current measurement, and
a second delta-sigma ADC for individual cell and battery voltage, and temperature measurement.
Charge and Discharge Counting
The integrating delta-sigma ADC measures the charge/discharge flow of the battery by measuring the voltage
drop across a small-value sense resistor between the SR1 and SR2 pins. The integrating ADC measures bipolar
signals from -0.25 V to 0.25 V. The bq20z65-R1 detects charge activity when VSR = V(SRP)-V(SRN)is positive and
discharge activity when VSR = V(SRP) - V(SRN) is negative. The bq20z65-R1 continuously integrates the signal over
time, using an internal counter. The fundamental rate of the counter is 0.65nVh.
Voltage
The bq20z65-R1 updates the individual series cell voltages at one second intervals. The internal ADC of the
bq20z65-R1 measures the voltage, scales and calibrates it appropriately. This data is also used to calculate the
impedance of the cell for the Impedance Track™ gas-gauging.
Current
The bq20z65-R1 uses the SRP and SRN inputs to measure and calculate the battery charge and discharge
current using a 5mΩ to 20mΩ typ. sense resistor.
Wake Function
The bq20z65-R1 can exit sleep mode, if enabled, by the presence of a programmable level of current signal
across SRP and SRN.
Auto Calibration
The bq20z65-R1 provides an auto-calibration feature to cancel the voltage offset error across SRN and SRP for
maximum charge measurement accuracy. The bq20z65-R1 performs auto-calibration when the SMBus lines stay
low continuously for a minimum of a programmable amount of time.
Temperature
The bq20z65-R1 has an internal temperature sensor and 2 external temperature sensor inputs, TS1 and TS2,
used in conjunction with two identical NTC thermistors (default are Semitec 103AT) to sense the battery
environmental temperature. The bq20z65-R1 can be configured to use the internal temperature sensor or up to 2
external temperature sensors.
16
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SLUS990 –DECEMBER 2009
COMMUNICATIONS
The bq20z65-R1 uses SMBus v1.1 with Master Mode and package error checking (PEC) options per the SBS
specification.
SMBus On and Off State
The bq20z65-R1 detects an SMBus off state when SMBC and SMBD are logic-low for ≥ 2 seconds. Clearing this
state requires either SMBC or SMBD to transition high. Within 1 ms, the communication bus is available.
SBS Commands
Table 3. SBS COMMANDS
SBS
CMD
SIZE IN
BYTES
MIN
VALUE
MAX
VALUE
DEFAULT
VALUE
MODE NAME
FORMAT
UNIT
0x00
0x01
0x02
R/W
R/W
R/W
ManufacturerAccess
Hex
2
2
2
0x0000
0xffff
—
—
RemainingCapacityAlarm
RemainingTimeAlarm
Integer
0
0
700 or 1000 300 or 432
mAh or 10mWh
min
Unsigned
integer
30
10
0x03
0x04
0x05
R/W
R/W
R
BatteryMode
AtRate
Hex
2
2
2
0x0000
–32,768
0
0xffff
—
—
—
—
Integer
32,767
65,535
mA or 10mW
min
AtRateTimeToFull
Unsigned
integer
0x06
0x07
0x08
0x09
R
R
R
R
AtRateTimeToEmpty
AtRateOK
Unsigned
integer
2
2
2
2
0
0
0
0
65,535
65,535
65,535
20,000
—
—
—
—
min
—
Unsigned
integer
Temperature
Voltage
Unsigned
integer
0.1°K
mV
Unsigned
integer
0x0a
0x0b
0x0c
R
R
R
Current
Integer
Integer
2
2
1
–32,768
–32,768
0
32767
32,767
100
—
—
—
mA
mA
%
AverageCurrent
MaxError
Unsigned
integer
0x0d
0x0e
0x0f
R
RelativeStateOfCharge
AbsoluteStateOfCharge
RemainingCapacity
FullChargeCapacity
RunTimeToEmpty
Unsigned
integer
1
1
2
2
2
2
2
2
2
0
0
0
0
0
0
0
0
0
100
—
—
—
—
—
—
—
—
—
%
R
Unsigned
integer
100+
%
R/W
R
Unsigned
integer
65,535
65,535
65,534
65,534
65,534
65,534
65,534
mAh or 10mWh
0x10
0x11
0x12
0x13
0x14
0x15
Unsigned
integer
mAh or 10mWh
R
Unsigned
integer
min
min
min
mA
mV
R
AverageTimeToEmpty
AverageTimeToFull
ChargingCurrent
Unsigned
integer
R
Unsigned
integer
R
Unsigned
integer
R
ChargingVoltage
Unsigned
integer
0x16
0x17
R
BatteryStatus
CycleCount
Hex
2
2
0x0000
0
0xdbff
—
0
—
—
R/W
Unsigned
integer
65,535
0x18
R/W
DesignCapacity
Integer
2
0
32,767
4400 or 6336 mAh or 10mWh
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
Table 3. SBS COMMANDS (continued)
SBS
SIZE IN
BYTES
MIN
VALUE
MAX
VALUE
DEFAULT
VALUE
MODE NAME
CMD
FORMAT
UNIT
0x19
0x1a
0x1b
R/W
R/W
R/W
DesignVoltage
Integer
Hex
2
2
2
7000
0x0000
0
18,000
0xffff
14,400
0x0031
0
mV
—
SpecificationInfo
ManufactureDate
Unsigned
integer
65,535
—
0x1c
0x20
R/W
R/W
SerialNumber
Hex
2
0x0000
—
0xffff
—
0x0000
—
—
ManufacturerName
String
20+1
Texas
Instruments
0x21
0x22
0x23
0x2f
R/W
R/W
R
DeviceName
String
String
String
String
20+1
4+1
14+1
20+1
2
—
—
—
—
0
—
bq20z65-R1
—
—
—
—
mV
DeviceChemistry
ManufacturerData
Authenticate
—
LION
—
—
R/W
R
—
—
0x3c
CellVoltage4
Unsigned
integer
65,535
—
0x3d
0x3e
0x3f
R
R
R
CellVoltage3
CellVoltage2
CellVoltage1
Unsigned
integer
2
2
2
0
0
0
65,535
65,535
65,535
—
—
—
mV
mV
mV
Unsigned
integer
Unsigned
integer
Table 4. EXTENDED SBS COMMANDS
SBS
CMD
SIZE IN
BYTES
MIN
VALUE
MAX
VALUE
DEFAULT
VALUE
MODE NAME
FORMAT
UNIT
0x45
0x46
0x4f
R
AFEData
String
Hex
Hex
Hex
Hex
Hex
Hex
Hex
Hex
11+1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
%
R/W
R
FETControl
StateOfHealth
SafetyStatus
PFAlert
2
2
2
2
2
2
2
2
2
0x00
0xff
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0
0xffff
0xffff
0xffff
0xffff
0xffff
0xffff
0xffff
65,535
0x51
0x52
0x53
0x54
0x55
0x57
0x58
R
—
—
—
—
—
—
—
R
R
PFStatus
R
OperationStatus
ChargingStatus
ResetData
R
R
R
WDResetData
Unsigned
integer
0x5a
0x5d
R
R
PackVoltage
Unsigned
integer
2
2
0
0
65,535
65,535
—
—
mV
mV
AverageVoltage
Unsigned
integer
0x5e
0x5f
R
TS1Temperature
TS2Temperature
UnSealKey
Integer
Integer
Hex
2
2
4
4
4
4
4
4
4
2
2
-400
-400
1200
1200
—
—
—
—
—
—
—
—
—
—
—
0.1°C
0.1°C
—
R
0x60
0x61
0x62
0x63
0x64
0x65
0x66
0x68
0x69
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
0x00000000 0xffffffff
0x00000000 0xffffffff
0x00000000 0xffffffff
0x00000000 0xffffffff
0x00000000 0xffffffff
0x00000000 0xffffffff
0x00000000 0xffffffff
FullAccessKey
PFKey
Hex
—
Hex
—
AuthenKey3
AuthenKey2
AuthenKey1
AuthenKey0
SafetyAlert2
SafetyStatus2
Hex
—
Hex
—
Hex
—
Hex
—
Hex
0x0000
0x0000
0x000f
0x000f
—
R
Hex
—
18
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
bq20z65-R1
www.ti.com
SBS
SLUS990 –DECEMBER 2009
Table 4. EXTENDED SBS COMMANDS (continued)
SIZE IN
BYTES
MIN
VALUE
MAX
VALUE
DEFAULT
MODE NAME
FORMAT
UNIT
CMD
0x6a
0x6b
0x6c
0x6d
0x6e
0x6f
VALUE
R
PFAlert2
Hex
2
0x0000
0x000f
0x000f
—
—
—
—
—
—
—
—
—
μΩ
R
PFStatus2
Hex
2
0x0000
—
R
ManufBlock1
ManufBlock2
ManufBlock3
ManufBlock4
ManufacturerInfo
SenseResistor
String
String
String
String
String
20
20
20
20
31+1
2
—
—
—
—
—
0
—
R
—
—
R
—
—
R
—
—
0x70
0x71
R/W
R/W
—
—
Unsigned
integer
65,535
—
0x72
0x73
0x74
0x77
0x78
0x79
0x7a
0x7b
0x7c
0x7d
0x7e
0x7f
R
TempRange
Hex
2
—
—
—
—
0xffff
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
R
LifetimeData1
String
String
Hex
32+1
8+1
2
—
R
LifetimeData2
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
DataFlashSubClassID
0x0000
—
DataFlashSubClassPage1 Hex
DataFlashSubClassPage2 Hex
DataFlashSubClassPage3 Hex
DataFlashSubClassPage4 Hex
DataFlashSubClassPage5 Hex
DataFlashSubClassPage6 Hex
DataFlashSubClassPage7 Hex
DataFlashSubClassPage8 Hex
32
32
32
32
32
32
32
32
—
—
—
—
—
—
—
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): bq20z65-R1
bq20z65-R1
SLUS990 –DECEMBER 2009
www.ti.com
APPLICATION SCHEMATIC
20
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): bq20z65-R1
PACKAGE OPTION ADDENDUM
www.ti.com
4-Jan-2010
PACKAGING INFORMATION
Orderable Device
BQ20Z65DBT-R1
BQ20Z65DBTR-R1
Status (1)
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
TSSOP
DBT
44
40 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TSSOP
DBT
44
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Logic
Power Mgmt
Microcontrollers
RFID
Telephony
Video & Imaging
Wireless
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
相关型号:
BQ20Z65DBT
SBS 1.1 compliant Gas Gauge with Impedance Track Technology and advanced charging algorithm 44-TSSOP -40 to 85
TI
BQ20Z65DBTR
SBS 1.1 compliant Gas Gauge with Impedance Track Technology and advanced charging algorithm 44-TSSOP -40 to 85
TI
BQ20Z70
SBS 1.1-COMPLIANT GAS GAUGE ENABLED WITH IMPEDANCE TRACK⑩ TECHNOLOGY FOR USE WITH THE bq29330
TI
©2020 ICPDF网 联系我们和版权申明