BQ25898D [TI]
具有电源路径和 HVDCP 的 I2C 单节 4A 降压电池充电器;型号: | BQ25898D |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有电源路径和 HVDCP 的 I2C 单节 4A 降压电池充电器 电池 |
文件: | 总66页 (文件大小:1757K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
bq25898、bq25898D I2C 控制单节 4A 快速充电器,采用 MaxCharge™
技术实现高输入电压和可调节电压 USB On-the-Go 升压模式,
1 特性
•
高集成度,包括所有 MOSFET、电流感测和环路补
偿
1
•
高效率 4A、1.5MHz 开关模式降压充电器
•
•
12μA 低电池泄漏电流,支持运输模式
–
充电效率高达 92%(3A 充电电流下)和
91%(4A 充电电流下)
高精度
–
–
–
±0.5% 充电电压调节
±5% 充电电流调节
±7.5% 输入电流调节
–
–
针对高电压输入 (9V/12V) 进行了优化
低功耗 PFM 模式,适用于轻负载操作
•
USB On-the-Go (OTG),可调输出电压范围为
4.5V 至 5.5V
•
•
安全
–
可选 500KHz/1.5MHz 升压转换器,输出电流高
达 2.4A
–
–
用于充电模式和升压模式的电池温度感测
热调节和热关断
–
–
5V、1A 输出电流时升压效率为 94%
采用 2.8mm x 2.5mm 42 焊球芯片尺寸球状引脚栅
格阵列 (DSBGA) 封装
精确的断续模式过流保护
•
单个输入,支持 USB 输入和可调高压适配器
2 应用
–
–
支持 3.9V 至 14V 输入电压范围
•
•
•
智能手机
输入电流限制(100mA 至 3.25A,分辨率为
50mA),支持 USB2.0、USB3.0 标准和高压
适配器
平板电脑
便携式网络设备
–
–
–
通过输入电压限制(最高 14V)实现最大功率
跟踪,适用于各类适配器
3 说明
自动检测 USB SDP、CDP、DCP 以及非标准
适配器 (bq25898)
bq25898 和 bq25898D 是适用于锂离子电池和锂聚合
物电池的高度集成型 4A 开关模式电池充电管理和系统
电源路径管理器件。该器件支持高输入电压快速充电。
可编程的 D+/D- 驱动器,用于非标准适配器握
手
器件信息(1)
•
•
远程电池感测
器件型号
bq25898
bq25898D
封装
封装尺寸(标称值)
2.80mm x 2.50mm
2.80mm x 2.50mm
输入电流优化器 (ICO),无需过载适配器即可最大
限度提高输入功率
DSBGA (42)
DSBGA (42)
•
•
充电器输出与电池终端间的电阻补偿 (IRCOMP)
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
借助 5mΩ 电池放电金属氧化物半导体场效应晶体
管 (MOSFET) 实现最高电池放电效率,放电电流高
达 9A
录。
简化电路原理图
•
•
集成 ADC,用于系统监视
(电压、温度和充电电流)
SYS
3.5Vœ4.5V
INPUT
3.9Vœ14V
窄 VDC (NVDC) 电源路径管理
USB
OTG
5V
–
–
与无电池或深度放电电池工作时可瞬时接通
电池管理模式中的理想二极管运行
ICHG
•
•
BATFET 控制,支持运输模式、唤醒和完全系统复
位
灵活的自主和 I2C 模式,可实现最优系统性能
I2C BUS
Optional
Host
REGN
Host Control
TS
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SLUSCA6
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
目录
9.3 Device Functional Modes........................................ 33
9.4 Register Map........................................................... 34
10 Application and Implementation........................ 51
10.1 Application Information.......................................... 51
10.2 Typical Application Diagram ................................. 51
10.3 System Example ................................................... 56
11 Power Supply Recommendations ..................... 57
12 Layout................................................................... 57
12.1 Layout Guidelines ................................................. 57
12.2 Layout Example .................................................... 57
13 器件和文档支持 ..................................................... 58
13.1 器件支持 ............................................................... 58
13.2 相关链接................................................................ 58
13.3 接收文档更新通知 ................................................. 58
13.4 社区资源................................................................ 58
13.5 商标....................................................................... 58
13.6 静电放电警告......................................................... 58
13.7 Glossary................................................................ 58
14 机械、封装和可订购信息....................................... 58
1
2
3
4
5
6
7
8
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
说明 (续).............................................................. 3
Device Comparison Table..................................... 4
Pin Configuration and Functions......................... 5
Specifications......................................................... 7
8.1 Absolute Maximum Ratings ...................................... 7
8.2 ESD Ratings.............................................................. 7
8.3 Recommended Operating Conditions....................... 8
8.4 Thermal Information.................................................. 8
8.5 Electrical Characteristics........................................... 8
8.6 Timing Requirements.............................................. 12
8.7 Typical Characteristics............................................ 14
Detailed Description ............................................ 16
9.1 Functional Block Diagram ....................................... 16
9.2 Feature Description................................................. 17
9
4 修订历史记录
Changes from Revision A (December 2016) to Revision B
Page
•
完整数据表已更新到产品文件夹 ............................................................................................................................................ 1
Changes from Original (March 2016) to Revision A
Page
•
•
•
•
•
•
•
•
•
已更改 已在特性中将 93% 更改为 94% ................................................................................................................................. 1
Changed anode to cathode in BTST...................................................................................................................................... 6
Changed cathode to anode in REGN..................................................................................................................................... 6
Changed falling to rising in tACOV_RISING test conditions in Electrical Characteristics .............................................................. 9
Deleted USB SDP (USB100) and the OTG Pin column from 表 3 and 表 4........................................................................ 19
已更改 VREF to VREGN in 公式 2 ...................................................................................................................................... 25
已更改 VREF to VREGN in 图 18 ........................................................................................................................................ 26
已更改 260 Ω to 232 Ω in Input Current Limit on ILIM ........................................................................................................ 28
已添加 note to 图 49 ............................................................................................................................................................ 51
2
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
5 说明 (续)
其低阻抗电源路径对开关模式运行效率进行了优化、缩短了电池充电时间并延长了放电阶段的电池使用寿命。具有
充电和系统设置的 I2C 串行接口使得此器件成为一个真正的灵活解决方案。
bq25898/98D 是一款适用于单节锂离子电池和锂聚合物电池的高度集成型 4A 开关模式电池充电管理和系统电源路
径管理器件。该器件 支持 高输入电压快速充电,适用于各类智能手机、平板电脑和便携式设备。其低阻抗电源路
径对开关模式运行效率进行了优化、缩短了电池充电时间并延长了放电阶段的电池使用寿命。该器件还集成了输入
电流优化器 (ICO) 和电阻补偿 (IRCOMP),从而为电池提供最大充电功率。该解决方案在系统和电池之间高度集成
输入反向阻断场效应晶体管 (FET)(RBFET,Q1)、高侧开关 FET(HSFET,Q2)、低侧开关 FET
(LSFET,Q3)以及电池 FET(BATFET、Q4)。它还集成了自举二极管以进行高侧栅极驱动和电池监视,从而
简化系统设计。具有充电和系统设置的 I2C 串行接口使得此器件成为一个真正的灵活解决方案。
该器件支持多种输入源,包括标准 USB 主机端口、USB 充电端口以及兼容 USB 的可调节高电压适配器。为支持
通过可调节高电压适配器进行快速充电,bq25898D 提供了 MaxCharge™握手支持(使用 D+/D- 引脚和 DSEL 引
脚)以进行 USB 开关控制。此外,bq25898D 和 bq25898 还提供有相应的接口,以支持采用输入电流脉冲协议的
可调节高电压适配器。为了设定默认输入电流限值,器件使用内置 USB 接口 (bq25898D) 或者从系统检测电路
(如 USB PHY 器件)(bq25898) 中获取结果。该器件符合 USB 2.0 和 USB 3.0 电源规范,具有输入电流和电压
调节功能。此外,输入电流优化器 (ICO) 还能够检测输入源未发生过载时的最大功率点。该器件还具有高达 2.4A
的限流能力,能够为 VBUS 提供 5V(4.5V-5.5V 可调节)电压,符合 USB On-the-Go (OTG) 运行功率额定值规
范。
电源路径管理将系统电压调节为稍稍高于电池电压,但是又不会下降到低于 3.5V 最小系统电压(可编程)。借助
于这个特性,即使在电池电量完全耗尽或者电池被拆除时,系统也能保持运行。当达到输入电流限值或电压限值
时,电源路径管理自动将充电电流减少为 0。随着系统负载持续增加,电源路径在满足系统电源需求之前将电池放
电。这种工作方式可防止输入源发生过载。
此器件在无需软件控制情况下启动并完成一个充电周期。它自动检测电池电压并通过三个阶段为电池充电:预充
电、恒定电流和恒定电压。在充电周期的末尾,当充电电流低于在恒定电压阶段中预设定的限值时,充电器自动终
止。当整个电池下降到低于再充电阈值时,充电器将自动启动另外一个充电周期。
此充电器提供针对电池充电和系统运行的多种安全 特性 ,其中包括电池负温度系数热敏电阻监视、充电安全定时
器和过压/过流保护。当结温超过 120°C(可设定)时,热调节减少充电电流。STAT 输出报告充电状态和任何故障
条件。PG 输出 (bq25898) 指示电源是否正常。当故障发生时,INT 会立即通知主机。
该器件还提供了一个 7 位模数转换器 (ADC),用于监视充电电流和输入/电池/系统(VBUS、BAT、SYS、TS)电
压。QON 引脚提供 BATFET 使能/复位控制,以使器件退出低功耗出厂模式或完全系统复位功能。
这些器件采用 42 焊球、2.8 mm x 2.5mm DSBGA 封装。
Copyright © 2016–2017, Texas Instruments Incorporated
3
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
6 Device Comparison Table
bq25898D
bq25898
I2C Address
Charge Mode Frequency
Boost Mode Frequency
USB Detection
6AH (1101010B + R/W)
6BH (1101011B + R/W)
1.5 MHz
1.5 MHz
1.5 MHz (default) / 500 KHz
PSEL/OTG
14.0 V
1.5 MHz (default) / 500 KHz
D+/D–
14.0 V
6 V
VBUS Overvoltage
REGN LDO
6 V
Default Adapter Current Limit
Default Battery Charge Voltage
Maximum Charge Current
Default Charge Current
Default Pre-charge Current
Maximum Pre-charge Current
Maximum Boost Mode Output Current
Charging Temperature Profile
Status Output
3.25 A
4.208 V
4.032 A
2.048 A
128 mA
1.024 A
2.4A
3.25 A
4.208 V
4.032 A
2.048 A
128 mA
1.024A
2.4A
JEITA
STAT
JEITA
STAT, PG
4
Copyright © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
7 Pin Configuration and Functions
bq25898
YFF Package 42-Pin DSBGA
Top View
bq25898D
YFF Package 42-Pin DSBGA
Top View
1
2
3
4
5
6
1
2
3
4
5
6
A
A
SYS
SYS
REGN
REGN
BAT
BAT
TS
TS
SCL
SCL
BTST
BTST
VOK
SW
DESL
SW
SYS
SDA
SYS
SDA
BAT
BAT
BAT
BAT
B
C
CE
QON
B
C
CE
QON
PGND
PGND
SYS
SYS
PSEL
PG
SYS
SYS
D+
D-
OTG
OTG
BAT
BAT
D
E
F
PMID
D
E
F
PMID
SW
SW
PGND
PGND
PGND
PGND
SW
SW
PGND
PGND
PGND
PGND
BAT
BAT
SYS
INT
SYS
INT
VBUS
VBUS
VBUS
VBUS
VBUS
VBUS
PMID
PMID
PMID
PMID
PMID
PMID
BATSEN
BATSEN
SW
SW
SW
SW
G
G
STAT
STAT
ILIM
ILIM
Pin Functions
PIN
TYPE(1)
DESCRIPTION
NAME
bq25898
bq25898D
Charger Input Voltage. The internal n-channel reverse block MOSFET (RBFET) is connected
between VBUS and PMID with VBUS on source. Place a 1-µF ceramic capacitor from VBUS to
PGND and place it as close as possible to IC.
VBUS
E3-G3
E3-G3
P
Positive line of the USB data line pair. D+/D- based USB host/charging port detection. The
detection includes data contact detection (DCD), primary and secondary detection in BC1.2, and
Adjustable high voltage adapter.
D+
PSEL
D–
–
C3
–
C3
–
AIO
DI
Power source selection input. High indicates a USB host source and Low indicates an adapter
source.
Negative line of the USB data line pair. D+/D- based USB host/charging port detection. The
detection includes data contact detection (DCD), primary and secondary detection in BC1.2, and
Adjustable high voltage adapter.
D3
AIO
Open drain active low power good indicator. Connect to the pull up rail via 10-kΩ resistor. LOW
indicates a good input source if the input voltage is within VVBUS_OP, above SLEEP mode threshold
(VSLEEPZ), and current limit is above IBATSRC(30 mA).
PG
D3
G1
–
DO
DO
Open drain charge status output to indicate various charger operation. Connect to the pull up rail
via 10-kΩ resistor. LOW indicates charge in progress. HIGH indicates charge complete or charge
disabled. When any fault condition occurs, STAT pin blinks in 1 Hz. The STAT pin function can be
disabled when STAT_DIS bit is set.
STAT
G1
SCL
SDA
A3
B3
A3
B3
DI
I2C Interface clock. Connect SCL to the logic rail through a 10-kΩ resistor.
I2C Interface data. Connect SDA to the logic rail through a 10-kΩ resistor.
DIO
Open-drain Interrupt Output. Connect the INT to a logic rail via 10-kΩ resistor. The INT pin sends
active low, 256-μs pulse to host to report charger device status and fault.
INT
F2
C4
F2
C4
DO
DI
Active high enable pin during boost mode. Deleted text form the OTG pin Description "OTG = High,
IINLIM is set to USB500 mode". The boost mode is activated when OTG_CONFIG =1 and OTG pin
is highChanged the Description of the OTG pin in the Pin Functions table.
OTG
(1) DI (Digital Input), DO (Digital Output), DIO (Digital Input/Output), AI (Analog Input), AO (Analog Output), AIO (Analog Input/Output)
Copyright © 2016–2017, Texas Instruments Incorporated
5
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
Pin Functions (continued)
PIN
TYPE(1)
DESCRIPTION
NAME
bq25898
bq25898D
Active low Charge Enable pin. Battery charging is enabled when CHG_CONFIG = 1 and CE pin =
Low. CE pin must be pulled High or Low.
CE
B4
B4
DI
Input current limit Input. ILIM pin sets the maximum input current and can be used to monitor input
current ILIM pin sets the maximum input current limit by regulating the ILIM voltage at 0.8 V. A
resistor is connected from ILIM pin to ground to set the maximum limit as IINMAX = KILIM/RILIM. The
actual input current limit is the lower limit set by ILIM pin (when EN_ILIM bit is high) or IIINLIM
register bits. Input current limit of less than 500 mA is not support on ILIM pin. ILIM pin can also be
used to monitor input current when the voltage is below 0.8V. The input current is proportional to
the voltage on ILIM pin and can be calculated by IIN = (KILIM x VILIM) / (RILIM x 0.8) The ILIM pin
function can be disabled when EN_ILIM bit is 0.
ILIM
TS
G2
A4
G2
A4
AI
AI
Temperature qualification voltage input. Connect a negative temperature coefficient thermistor.
Program temperature window with a resistor divider from REGN to TS to GND. Charge suspends
when either TS pin is out of range. Recommend 103AT-2 thermistor.
BATFET enable/reset control input. When BATFET is in ship mode, a logic low of tSHIPMODE (typical
1sec) duration turns on BATFET to exit shipping mode. . When VBUS is not plugged-in, a logic low
of tQON_RST (typical 19.5sec) duration resets SYS (system power) by turning BATFET off for
tBATFET_RST (typical 0.325sec) and then re-enable BATFET to provide full system power reset. The
pin contains an internal pull-up to maintain default high logic
QON
BAT
B6
B6
DI
P
Battery connection point to the positive terminal of the battery pack. The internal BATFET is
connected between BAT and SYS. Connect a 10uF closely to the BAT pin.
A1-E1
A1-E1
System connection point. The internal BATFET is connected between BAT and SYS. When the
battery falls below the minimum system voltage, switch-mode converter keeps SYS above the
minimum system voltage. Connect a 20uF closely to the SYS pin.
SYS
PGND
SW
A2-E2
C6-G6
C5-G5
A2-E2
C6-G6
C5-G5
P
P
P
Power ground connection for high-current power converter node.
Switching node connecting to output inductor. Internally SW is connected to the source of the n-
channel HSFET and the drain of the n-channel LSFET. Connect the 0.047μF bootstrap capacitor
from SW to BTST.
PWM high side driver positive supply. Internally, the BTST is connected to the cathode of the
boost-strap diode. Connect the 0.047μF bootstrap capacitor from SW to BTST.
BTST
A6
A5
A6
A5
P
P
PWM low side driver positive supply output. Internally, REGN is connected to the anode of the
boost-strap diode. Connect a 4.7 µF (10 V rating) ceramic capacitor from REGN to analog GND.
The capacitor should be placed close to the IC. REGN also serves as bias rail of TS pin.
REGN
Connected to the drain of the reverse blocking MOSFET (RBFET) and the drain of HSFET. Given
the total input capacitance, put 1µF on VBUS to PGND, and the rest capacitance on PMID to
PGND.
PMID
DSEL
D4-G44
–
D4-G4
B5
DO
DO
Active high D+/D- multiplexer selection control. Connect a 47-nF (6V rating) ceramic capacitor from
DSEL to analog GND. The pin is normally low. During input source type detection, the pin drives
high to indicate the bq25890 D+/D- detection is in progress and needs to take control of D+, D-
signals. When detection is completed, the pin keeps high when DCP, MaxCharge or HVDCP is
detected. The pin returns to low when other input source type is detected
VOK
B5
F1
–
DO
AI
LDO output to driver USB PHY/MUX. Connect a 47nF ceramic capacitor from VOK to analog GND.
Remote battery sense input. The typical pin resistance is 800 kΩ. Connect as close to battery as
possible.
BATSEN
F1
6
Copyright © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
8 Specifications
8.1 Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–2
MAX
22
22
20
7
VALUE
V
VBUS (converter not switching)
PMID (converter not switching)
STAT
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
–3
V
V
PG (bq25898)
V
PSEL (bq25898)
7
V
VOK (bq25898)
7
V
DSEL (bq25898D)
7
V
D+, D– (bq25898D)
7
V
Voltage range (with respect to GND)
BTST
20
16
6
V
SW
V
BAT, SYS (converter not switching)
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
V
SDA, SCL, INT, OTG, REGN, TS, CE, QON
7
V
BTST TO SW
PGND to GND
BATSEN
7
V
0.3
7
V
V
ILIM
5
V
INT, STAT
6
mA
mA
mA
mA
°C
°C
PG (bq25898)
Output sink current
6
DSEL (bq25898D)
5
VOK (bq25898)
Junction temperature
5
–40
–65
150
150
Storage temperature range, Tstg
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage
values are with respect to the network ground terminal unless otherwise noted.
8.2 ESD Ratings
VALUE
UNIT
(1)
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001
±2000
V
VESD
Electrostatic discharge
Charged device model (CDM), per JEDEC specification
JESD22-C101(2)
±250
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
Copyright © 2016–2017, Texas Instruments Incorporated
7
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
MAX UNIT
8.3 Recommended Operating Conditions
MIN
VIN
Input voltage
3.9
14(1)
V
A
A
V
A
A
IIN
Input current (VBUS)
Output current (SW)
Battery voltage
3.25
ISYS
VBAT
4
4.608
4
Fast charging current
Up to 6 (continuos)
IBAT
Discharging current with internal MOSFET
Operating free-air temperature range
9 (peak)
(Up to 1 sec duration)
A
TA
–40
85
°C
(1) The inherent switching noise voltage spikes should not exceed the absolute maximum rating on either the BTST or SW pins. A tight
layout minimizes switching noise.
8.4 Thermal Information
bq25898,
bq25898D
THERMAL METRIC(1)
UNIT
YFF (DSBGA)
42-BALL
53.5
0.2
RθJA
Junction-to-ambient thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJCtop
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
8.2
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.9
ψJB
8.2
RθJCbot
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
8.5 Electrical Characteristics
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
QUIESCENT CURRENTS
VBAT = 4.2 V, V(VBUS) < V(UVLO), leakage
between BAT and VBUS
5
µA
µA
High-Z Mode, No VBUS, BATFET Disabled
(REG09[5] = 1), Battery Monitor Disabled, TJ
< 85°C
12
32
23
IBAT
Battery discharge current (BAT, SW, SYS) in buck mode
High-Z Mode, No VBUS, BATFET Enabled
(REG09[5] = 0), Battery Monitor Disabled, TJ
< 85°C
60
µA
V(VBUS)= 5 V, High-Z Mode, No Battery,
Battery Monitor Disabled
15
25
1.5
3
35
50
3
µA
µA
Input supply current (VBUS) in buck mode when High-Z mode
is enabled
I(VBUS_HIZ)
V(VBUS)= 12 V, High-Z Mode, No Battery,
Battery Monitor Disabled
VBUS > V(UVLO), VBUS > VBAT, Converter not
switching
mA
mA
mA
mA
VBUS > V(UVLO), VBUS > VBAT, Converter
switching, VBAT = 3.2V, ISYS = 0A
I(VBUS)
Input supply current (VBUS) in buck mode
Battery discharge current in boost mode
VBUS > V(UVLO), VBUS > VBAT, Converter
switching, VBAT = 3.8 V, ISYS = 0 A
3
VBAT = 4.2 V, Boost mode, I(VBUS)= 0 A,
Converter switching
I(BOOST)
5
VBUS/BAT POWER UP
V(VBUS_OP)
VBUS operating range
3.9
3.6
14
V
V
VBUS for active I2C, no battery
Sleep mode falling threshold
Sleep mode rising threshold
V(VBUS_UVLOZ)
V(SLEEP)
25
65
120
370
mV
mV
V(SLEEPZ)
130
250
8
Copyright © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
Electrical Characteristics (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values (unless
otherwise noted)
PARAMETER
VBUS over-voltage rising threshold
VBUS over-voltage falling threshold
ACOV rising deglitch
TEST CONDITIONS
MIN
13.9
13.3
TYP
MAX
14.6
13.9
UNIT
V
V(ACOV)
V
tACOV_RISING
VVBUS rising
VVBUS falling
1
1
µs
tACOV_FALLING
ACOV falling deglitch
ms
Battery for active I2C, no VBUS
Battery depletion falling threshold
Battery depletion rising threshold
Bad adapter detection threshold
Bad adapter detection current source
VBAT(UVLOZ)
2.3
V
VBAT(DPL)
VBAT(DPLZ)
V(VBUSMIN)
I(BADSRC)
2.15
2.35
2.5
2.7
V
V
3.8
30
V
mA
POWER-PATH MANAGEMENT
I(SYS) = 0 A, VBAT> VSYS(MIN), BATFET
Disabled (REG09[5]=1)
VBAT
50 mV
+
V
V
V
V
VSYS
Typical system regulation voltage
Isys = 0 A, VBAT< VSYS(MIN), BATFET
Disabled (REG09[5]=1)
VSYS(MIN)
250 mV
+
VBAT< VSYS(MIN), SYS_MIN = 3.5 V
(REG03[3:1] = 101), ISYS= 0 A
VSYS(MIN)
VSYS(MAX)
Minimum DC system voltage output
Maximum DC system voltage output
3.60
3.75
4.40
VBAT = 4.35 V, SYS_MIN = 3.5 V
(REG03[3:1] = 101), ISYS= 0 A
4.42
TJ = -40°C - 85°C
28
28
24
24
12
12
30
40
47
33
40
18
21
mΩ
mΩ
mΩ
mΩ
mΩ
mΩ
mV
Top reverse blocking MOSFET(RBFET) on-resistance between
VBUS and PMID
RON(RBFET)
RON(HSFET)
RON(LSFET)
TJ = -40°C - 125°C
TJ = -40°C - 85°C
Top switching MOSFET (HSFET) on-resistance between PMID
and SW
TJ = -40°C - 125°C
TJ = -40°C - 85°C
Bottom switching MOSFET (LSFET) on-resistance between
SW and GND
TJ = -40°C - 125°C
BAT discharge current 10 mA
V(FWD)
BATFET forward voltage in supplement mode
BATTERY CHARGER
VBAT(REG_RANGE)
VBAT(REG_STEP)
Typical charge voltage range
Typical charge voltage step
3.840
4.608
V
16
64
mV
VBAT = 4.208 V (REG06[7:2] = 010111) or
VBAT = 4.352 V (REG06[7:2] = 100000)
TJ = -40°C - 85°C
VBAT(REG)
Charge voltage resolution accuracy
-0.5%
0
0.5%
4032
I(CHG_REG_RANGE)
I(CHG_REG_STEP)
Typical fast charge current regulation range
Typical fast charge current regulation step
mA
mA
VBAT= 3.1 V or 3.8 V, ICHG = 256 mA
TJ = -40°C - 85°C
-20%
-5%
2.6
20%
5%
I(CHG_REG_ACC)
Fast charge current regulation accuracy
VBAT= 3.1 V or 3.8 V, ICHG = 1792 mA
TJ = -40°C - 85°C
Fast charge to precharge, BATLOWV
(REG06[1]) = 1
Battery LOWV falling threshold
Battery LOWV rising threshold
Battery LOWV falling threshold
Battery LOWV rising threshold
2.8
3.0
2.6
2.8
2.9
V
V
V
V
Precharge to fast charge, BATLOWV
(REG06[1]) = 1
(Typical 200-mV hysteresis)
2.8
2.5
3.15
2.7
VBAT(LOWV)
Fast charge to precharge, BATLOWV
(REG06[1]) = 0
Precharge to fast charge, BATLOWV
(REG06[1]) = 0
(Typical 200-mV hysteresis)
2.7
64
2.9
I(PRECHG_RANGE)
I(PRECHG_STEP)
I(PRECHG_ACC)
I(TERM_RANGE)
I(TERM_STEP)
Precharge current range
1024
mA
mA
Typical precharge current step
Precharge current accuracy
Termination current range
Typical termination current step
64
64
VBAT = 2.6 V, IPRECHG = 256 mA
–20%
64
20%
1024
mA
mA
ITERM = 256 mA, ICHG≤ 1344 mA
TJ = -20°C - 85°C
-20%
-20%
20%
20%
I(TERM_ACC)
Termination current accuracy
ITERM = 256 mA, ICHG> 1344 mA
TJ = -20°C - 85°C
V(SHORT)
Battery short voltage
VBAT falling
VBAT rising
VBAT < 2.2 V
2.0
200
110
V
V(SHORT_HYST)
I(SHORT)
Battery short voltage hysteresis
Battery short current
mV
mA
Copyright © 2016–2017, Texas Instruments Incorporated
9
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
Electrical Characteristics (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VBAT falling, VRECHG (REG06[0] = 0) = 0
VBAT falling, VRECHG (REG06[0] = 0) = 1
VBAT = 4.2 V
MIN
TYP
100
200
MAX
UNIT
mV
mV
mA
mA
mΩ
mΩ
kΩ
V(RECHG)
Recharge threshold below VBATREG
IBAT(LOAD)
ISYS(LOAD)
Battery discharge load current
System discharge load current
15
30
VSYS = 4.2 V
TJ = 25°C
5
5
7
RON(BATFET)
RBATSEN
SYS-BAT MOSFET (BATFET) on-resistance
BATSEN input resistance
TJ = -40°C - 125°C
10
800
INPUT VOLTAGE / CURRENT REGULATION
VIN(DPM_RANGE)
VIN(DPM_STEP)
VIN(DPM_ACC)
IIN(DPM_RANGE)
IIN(DPM_STEP)
Typical input voltage regulation range
3.9
15.3
V
Typical input voltage regulation step
Input voltage regulation accuracy
Typical input current regulation range
Typical input current regulation step
100
mV
VINDPM = 4.4 V, 7.8 V, 10.8 V
IINLIM (REG00[5:0]) = 100 mA
-3%
100
3%
3250
mA
mA
50
90
Input current 100mA regulation accuracy
VBAT = 5V, current pulled from SW
IIN(DPM100_ACC)
85
100
mA
USB150, IINLIM (REG00[5:0]) = 150 mA
USB500, IINLIM (REG00[5:0]) = 500 mA
USB900, IINLIM (REG00[5:0]) = 900 mA
125
440
750
135
470
825
150
500
900
mA
mA
mA
Input current regulation accuracy
VBAT = 5V, current pulled from SW
IIN(DPM_ACC)
Adapter 1.5 A, IINLIM (REG00[5:0]) = 1500
mA
1300
1400
1500
200
mA
mA
IIN(START)
KILIM
Input current regulation during system start up
VSYS = 2.2 V, IINLIM (REG00[5:0]) ≥ 200 mA
IINMAX = KILIM/RILIM, Input Current regulation
by ILIM pin = 1.5 A
290
320
350
A x Ω
VOK (bq25898)/DSEL (bq25898D)
VBUS > 6 V I(VOK) = 20 mA and I(REGN) =
30 mA
4.75
4.35
5.25
V
VVOK_OH
Voltage
VBUS = 5 V I(VOK) = 5 mA and I(REGN) =
30 mA
4.8
0.4
V
V
V
VVOK_OL
Voltage
Voltage
Battery only VBAT = 3.8 V, I(VOK) = -10 mA
I(DSEL) = 20 mA and I(REGN) = 30 mA,
VBUS = 5 V
VDSEL_OH
1.3
I(DSEL) = -10 mA and I(REGN) = 30 mA,
VBUS = 5 V
VDSEL_OL
Voltage
0.4
V
D+/D- DETECTION (bq25898D)
I(10UA_ISRC)
D+ connection check current source
7
50
10
14
150
1
µA
µA
µA
µA
mA
kΩ
I(100UA_ISINK)
D+/D- current sink (100 µA)
100
D–, switch open
D+, switch open
–1
I(DPDM_LKG)
D+/D- Leakage current
–1
1
I(1P6MA_ISINK)
R(D–_DWN)
D+/D- current sink (1.6 mA)
1.35
14.25
1.60
HIZ
1.75
24.8
D– pulldown for connection check
REG01[7:5] = 000 (default) or REG01[4:2] =
000 (default)
VFLOAT_VDPSRC
D+/D- Voltage source (HIZ)
V
V0P0_VDSRC
V0P6_VDSRC
V1P2_DPVSRC
V2P0_DPVSRC
V2P7_DPVSRC
D+/D- Voltage source (0 V)
D+/D- Voltage source (0.6 V)
D+/D- Voltage source (1.2 V)
D+/D- Voltage source (2.0 V)
D+/D- Voltage source (2.7 V)
REG01[7:5] = 001 or REG01[4:2] = 001
REG01[7:5] = 010 or REG01[4:2] = 010
REG01[7:5] = 011 or REG01[4:2] = 011
REG01[7:5] = 100 or REG01[4:2] = 100
REG01[7:5] = 101 or REG01[4:2] = 101
0
0.5
0.15
0.7
V
V
V
V
V
0.6
1.2
2
1.075
1.875
2.575
1.325
2.125
2.825
2.7
REG01[7:5] = 110 or REG01[4:2] = 110 or
REG01[4:2] = 111
V3P3_DPVSRC
D+/D- Voltage source (3.3 V)
3.15
3.3
3.45
V
RDPDM_SHORT
V(0P4_VTH)
V(0P8_VTH)
V(2P7_VTH)
D+/D- Short REG01[7:5] = 111
D+/D- low comparator threshold
D+ low comparator threshold
200
400
0.8
Ω
mV
V
250
D+/D- comparator threshold for non-standard adapter detection
(Divider 1, 3,or 4)
2.55
1.85
1.05
2.85
V
V(2P0_VTH)
V(1P2_VTH)
D+/D- comparator threshold for non-standard adapter detection
(Divider 1, 3)
2.15
1.35
V
V
D+/D- comparator threshold for non-standard adapter detection
(Divider 2)
10
Copyright © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
Electrical Characteristics (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
BAT OVER-VOLTAGE/CURRENT PROTECTION
VBAT(OVP)
Battery over-voltage threshold
Battery over-voltage hysteresis
System over-current threshold
VBAT rising, as percentage of VBAT(REG)
VBAT falling, as percentage of VBAT(REG)
104%
2%
VBAT(OVP_HYST)
IBAT(FET_OCP)
9
A
THERMAL REGULATION AND THERMAL SHUTDOWN
TREG
Junction temperature regulation accuracy
Thermal shutdown rising temperature
Thermal shutdown hysteresis
REG08[1:0] = 11
Temperature rising
Temperature falling
120
160
30
°C
°C
°C
TSHUT
TSHUT(HYS)
JEITA THERMISTOR COMPARATOR (BUCK MODE)
T1 (0°C) threshold, charge suspended T1 below this
temperature.
V(T1)
As percentage to V(REGN)
As Percentage to V(REGN)
As Percentage to V(REGN)
As Percentage to V(REGN)
As percentage to V(REGN)
As Percentage to V(REGN)
As Percentage to V(REGN)
As Percentage to V(REGN)
72.75%
67.75%
44.25v
73.25%
1.4%
73.75%
68.75%
45.25%
34.875%
Charge back to ICHG/2 (REG04[6:0]) and VREG (REG06[7:2])
above this temperature.
V(T1_HYS)
V(T2)
V(T2_HYS)
V(T3)
V(T3_HYS)
V(T5)
T2 (10°C) threshold, charge back to ICHG/2 (REG04[6:0]) and
VREG (REG06[7:2]) below this temperature.
68.25%
1.4%
Charge back to ICHG (REG04[6:0]) and VREG (REG06[7:2])
above this temperature.
T3 (45°C) threshold,charge back to ICHG (REG04[6:0]) and
VREG-200mV (REG06[7:2]) above this temperature.
44.75%
1%
Charge back to ICHG (REG04[6:0]) and VREG (REG06[7:2])
below this temperature.
T5 (60°C) threshold, charge suspended above this
temperature.
33.875%
34.375%
1.25%
Charge back to ICHG (REG04[6:0]) and VREG-200mV
(REG06[7:2]) below this temperature.
V(T5_HYS)
COLD/HOT THERMISTOR COMPARATOR (BOOST MODE)
As percentage to VREGN REG01[5] = 1
(Approx. -20°C w/ 103AT)
V(BCOLD1)
Cold temperature threshold 1, TS pin voltage rising threshold
79.5%
80%
1%
80.5%
V(BCOLD1_HYS)
V(BHOT2)
Cold temperature threshold 1, TS pin voltage falling threshold
Hot temperature threshold 2, TS pin voltage falling threshold
Hot temperature threshold 2, TS pin voltage rising threshold
As percentage to VREGN REG01[5] = 1
As percentage to VREGN REG01[7:6] = 10
(Approx. 65°C w/ 103AT)
30.75%
31.25%
3%
31.75%
V(BHOT2_HYS)
PWM
As percentage to VREGN REG01[7:6] = 10
FSW
PWM switching frequency, and digital clock
Maximum PWM duty cycle
Oscillator frequency
1.32
1.68
MHz
DMAX
97%
64
BOOST MODE OPERATION
V(OTG_REG_RANGE) Typical boost mode regulation voltage range
V(OTG_REG_STEP)
4.55
-3%
5.55
3%
V
Typical boost Mode Regulation voltage step
Boost mode regulation voltage accuracy
mV
I(VBUS) = 0 A, BOOSTV = 4.998 V
(REG0A[7:4] = 0111)
V(OTG_REG_ACC)
BAT falling, REG03[0] = 0
BAT falling, REG03[0] = 1
2.7
2.4
0.5
1.5
5.8
2.9
2.6
V
V
A
A
V
V(OTG_BAT)
Battery voltage exiting boost mode
I(OTG)
Typical boost mode output current range
Boost mode RBFET over-current protection accuracy
Boost mode over-voltage threshold
2.45
2.0
I(OTG_OCP_ACC)
V(OTG_OVP)
REGN LDO
BOOST_LIM = 1.5 A (REG0A[2:0] = 100)
Rising threshold
6
V(VBUS) = 9 V, I(REGN) = 40 mA
V(VBUS) = 5 V, I(REGN) = 20 mA
V(VBUS) = 9 V, V(REGN) = 3.8 V
5.6
4.7
50
6
6.4
V
V
V(REGN)
I(REGN)
REGN LDO output voltage
REGN LDO current limit
4.8
mA
ANALOG-TO-DIGITAL CONVERTER (ADC)
RES
Resolution
Rising threshold
7
bits
V
V(VBUS) > VBAT + V(SLEEP) or OTG mode is
enabled
2.304
4.848
4.848
VBAT(RANGE)
Typical battery voltage range
Typical battery voltage resolution
V(VBUS) < VBAT + V(SLEEP) and OTG mode is
disabled
VSYS_MIN
V
V(BAT_RES)
20
mV
Copyright © 2016–2017, Texas Instruments Incorporated
11
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
Electrical Characteristics (continued)
VVBUS_UVLOZ < VVBUS < VACOV and VVBUS > VBAT + VSLEEP, TJ = –40°C to 125°C and TJ = 25°C for typical values (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
V(VBUS) > VBAT + V(SLEEP) or OTG mode is
enabled
2.304
4.848
V
V(SYS_RANGE)
Typical system voltage range
V(VBUS) < VBAT + V(SLEEP) and OTG mode is
disabled
VSYS_MIN
4.848
15.3
V
mV
V
V(SYS_RES)
Typical system voltage resolution
Typical VVBUS voltage range
20
V(VBUS) > VBAT + V(SLEEP) or OTG mode is
enabled
V(VBUS_RANGE)
V(VBUS_RES)
IBAT(RANGE)
2.6
Typical VVBUS voltage resolution
Typical battery charge current range
100
mV
A
V(VBUS) > VBAT + V(SLEEP) and VBAT
VBAT(SHORT)
>
0
4.032
80%
IBAT(RES)
Typical battery charge current resolution
Typical TS voltage range
50
mA
V(TS_RANGE)
V(TS_RES)
21%
Typical TS voltage resolution
0.47%
LOGIC I/O PIN (OTG, CE, PSEL, QON)
VIH
Input high threshold level
1.3
V
V
VIL
Input low threshold level
High level leakage current
0.4
1
IIN(BIAS)
Pull-up rail 1.8 V
Battery only mode
V(VBUS) = 9 V
µA
V
BAT
5.8
V(QON)
Internal /QON pull-up
V
V(VBUS) = 5 V
4.3
V
R(QON)
Internal /QON pull-up resistance
200
kΩ
LOGIC I/O PIN (INT, STAT, PG)
VOL
Output low threshold level
High level leakage current
Sink Current = 5 mA, Sink current
Pull-up rail 1.8 V
0.4
1
V
IOUT_BIAS
µA
I2C INTERFACE (SCL, SDA)
VIH
Input high threshold level, SCL and SDA
Pull-up rail 1.8 V
1.3
V
V
VIL
Input low threshold level
Output low threshold level
High level leakage current
Pull-up rail 1.8 V
0.4
0.4
1
VOL
IBIAS
Sink Current = 5 mA, Sink current
Pull-up rail 1.8 V
V
µA
8.6 Timing Requirements
MIN
NOM
MAX UNIT
VBUS/BAT POWER UP
tBADSRC
Bad adapter detection duration
30
msec
BAT OVER-VOLTAGE PROTECTION
Battery over-voltage deglitch time to disable
charge
tBATOVP
1
µs
BATTERY CHARGER
tRECHG
Recharge deglitch time
20
msec
Current Pulse Control
tPUMPX_STOP
tPUMPX_ON1
tPUMPX_ON2
tPUMPX_OFF
tPUMPX_DLY
Current pulse control stop pulse
430
240
70
570 msec
360 msec
130 msec
130 msec
225 msec
Current pulse control long on pulse
Current pulse control short on pulse
Current pulse control off pulse
70
Current pulse control stop start delay
80
BATTERY MONITOR
tCONV
Conversion time
CONV_RATE(REG02[6]) = 0
TJ = -10°C - 60°C
8
1000 msec
QON and SHIPMODE TIMING
QON low time to turn on BATFET and exit ship
mode
tSHIPMODE
0.8
1.3
23
sec
sec
tQON_RST
QON low time to enable full system reset
BATFET off time during full system reset
TJ = -10°C - 60°C
TJ = -10°C - 60°C
15.5
250
tBATFET_RST
400 msec
12
Copyright © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
Timing Requirements (continued)
MIN
NOM
MAX UNIT
tSM_DLY
Enter ship mode delay
SCL clock frequency
TJ = -10°C - 60°C
10
15
sec
I2C INTERFACE
fSCL
400
KHz
DIGITAL CLOCK and WATCHDOG TIMER
fLPDIG
fDIG
Digital low power clock
Digital clock
REGN LDO disabled
REGN LDO enabled
18
30
45
KHz
KHz
1320
1500
1680
WATCHDOG
(REG07[5:4])=11, REGN LDO
disabled
100
136
160
160
sec
sec
tWDT
Watchdog reset time
WATCHDOG
(REG07[5:4])=11, REGN LDO
enabled
版权 © 2016–2017, Texas Instruments Incorporated
13
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
8.7 Typical Characteristics
96
94
92
90
88
86
84
82
80
95
93
91
89
87
85
83
81
79
77
75
VBUS = 5V
VBUS = 9V
VBUS = 12V
VBUS = 5V
VBUS = 9V
VBUS = 12V
0
0.5
1
1.5
2
2.5
3
3.5
4
0
0.5
1
1.5
2
Charge Current (A)
System Load Current (A)
D001
D001
VBAT = 3.8 V
DCR = 10 mΩ
图 1. Charge Efficiency vs Charge Current
图 2. System Light Load Efficiency vs System Light Load
Current
96
94
92
90
88
86
84
82
80
8
6
4
2
0
-2
-4
-6
-8
VBAT = 3.1V
VBAT = 3.8V
VBAT = 3.1V
VBAT = 3.8V
0
0.5
1
1.5
VBUS (A)
2
2.5
0.5
1
1.5
2
2.5
3
3.5
4
Charge Current (A)
D001
D001
VBUS = 5 V
图 3. Boost Mode Efficiency vs VBUS Load Current
图 4. Charge Current Accuracy vs Charge Current I2C
Setting
3.82
3.78
3.74
3.70
3.66
3.62
3.58
3.54
3.50
4.5
4.45
4.4
4.35
4.3
4.25
4.2
4.15
4.1
4.05
4
0.0
0.5
1.0
1.5
2.0
2.5
3.0
0
0.5
1
1.5
2
2.5
3
Load Current (A)
Load Current (A)
D001
D001
VBAT = 2.6 V
VBUS = 5 V
SYSMIN = 3.5 V
VBAT = 4.2 V
图 6. SYS Voltage Regulation vs System Load Current
图 5. SYS Voltage Regulation vs System Load Current
14
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
Typical Characteristics (接下页)
4.30
4.28
4.26
4.24
4.22
4.20
4.18
4.16
4.14
4.12
4.10
1600
1400
1200
1000
800
600
400
200
0
IINLIM = 500mA
IINLIM = 900mA
IINLIM = 1.5A
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (oC)
-40 -25 -10
5
20 35 50 65 80 95 110 125
Temperature (oC)
D001
D001
VBUS = 5 V
图 7. BAT Voltage vs Temperature
图 8. Input Current Limit vs Temperature
96
94
92
90
88
86
84
82
80
-0.10
-0.15
-0.20
-0.25
-0.30
VBUS = 5V
VBUS = 9V
VBUS = 12V
VBUS = 5V
VBUS = 9V
VBUS = 12
0.5
1
1.5
2
2.5
3
3.8 3.85 3.9 3.95
4
4.05 4.1 4.15 4.2 4.25
Charge Current (A)
Battery Charge Voltage (V)
D001
D001
图 9. Charge Efficiency
图 10. Charge Voltage Accuracy
版权 © 2016–2017, Texas Instruments Incorporated
15
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9 Detailed Description
The device is a highly integrated 4-A switch-mode battery charger for single cell Li-Ion and Li-polymer battery. It
is highly integrated with the input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2) ,
low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4). The device also integrates the boostrap
diode for the high-side gate drive.
9.1 Functional Block Diagram
VBUS
RBFET
PMID
(Q1)
VVBUS_UVLOZ
UVLO
Q1 Gate
Control
V
BATZ +80mV
SLEEP
ACOV
REGN
BTST
REGN
LDO
EN_HIZ
V
ACOV
FBO
VBUS
VBUS_OVP_BOOST
Q2_UCP_BOOST
V OTG_OVP
IQ2
VINDPM
V OTG_HSZCP
SW
IQ3
VOTG_BAT
Q3_OCP_BOOST
HSFET (Q2)
REGN
CONVERTER
CONTROL
IINDPM
BAT
BATOVP
IC TJ
TREG
104%xVBAT_REG
BAT
I LSFET_UCP
LSFET (Q3)
V BAT_REG
PGND
UCP
IQ2
Q2_OCP
IQ3
SYS
I HSFET_OCP
VSYSMIN
EN_HIZ
EN_CHARGE
EN_BOOST
V BTST -VSW
ICHG_REG
REFRESH
VBTST_REFRESH
SYS
ICHG
REF
DAC
V BAT_REG
I CHG_REG
Q4 Gate
Control
IBADSRC
BATFET
(Q4)
BAD_SRC
IDC
ILIM
DSEL(bq25898D)
VOK(bq25898)
Converter
Control State
Machine
IC TJ
TSHUT
TSHUT
BAT
VQON
BAT
D+ (bq25898D)
Dœ (bq25898D)
PSEL(bq25898)
OTG
BAT_GD
Input
Source
Detection
VBATGD
/QON
ICHG
USB
ADC Control
Adapter
VBUS
BAT
SYS
TS
-VRECHG
VREG
BAT
RECHRG
ADC
INT
ICHG
TERMINATION
BATLOWV
CHARGE
CONTROL
STATE
ITERM
V BATLOWV
BAT
STAT
MACHINE
V SHORT
BAT
I2C
Interface
BATSHORT
SUSPEND
/PG (bq25898)
Battery
Sensing
TS
Thermistor
SCL SDA /CE BATSEN
Copyright © 2016, Texas Instruments Incorporated
16
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.2 Feature Description
9.2.1 Device Power-On-Reset (POR)
The internal bias circuits are powered from the higher voltage of VBUS and BAT. When VBUS rises above
VVBUS_UVLOZ or BAT rises above VBAT_UVLOZ , the sleep comparator, battery depletion comparator and BATFET
driver are active. I2C interface is ready for communication and all the registers are reset to default value. The
host can access all the registers after POR.
9.2.2 Device Power Up from Battery without Input Source
If only battery is present and the voltage is above depletion threshold (VBAT_DPLZ), the BATFET turns on and
connects battery to system. The REGN LDO stays off to minimize the quiescent current. The low RDS(ON) of
BATFET and the low quiescent current on BAT minimize the conduction loss and maximize the battery run time.
The device always monitors the discharge current through BATFET (see Supplement Mode). When the system is
overloaded or shorted (IBAT > IBATFET_OCP), the device turns off BATFET immediately and sets BATFET_DIS bit
to indicate BATFET is disabled until the input source plugs in again or one of the methods describe in BATFET
Enable (Exit Shipping Mode) is applied to re-enable BATFET.
9.2.3 Device Power Up from Input Source
When an input source is plugged in, the device checks the input source voltage to turn on REGN LDO and all the
bias circuits. It detects and sets the input current limit before the buck converter is started when
AUTO_DPDM_EN bit is set. The power up sequence from input source is as listed:
1. Power Up REGN LDO
2. Poor Source Qualification
3. Input Source Type Detection based on D+/D- (bq25898D) or PSEL (bq25898) to set default Input Current
Limit (IINLIM) register and input source type
4. Input Voltage Limit Threshold Setting (VINDPM threshold)
5. Converter Power-up
9.2.3.1 Power Up REGN Regulation (LDO)
The REGN LDO supplies internal bias circuits as well as the HSFET and LSFET gate drive. The LDO also
provides bias rail to TS external resistors. The pull-up rail of STAT and PG can be connected to REGN as well.
The REGN is enabled when all the below conditions are valid.
1. VBUS above VVBUS_UVLOZ
2. VBUS above VBAT + VSLEEPZ in buck mode or VBUS below VBAT + VSLEEP in boost mode
3. After 220 ms delay is completed
If one of the above conditions is not valid, the device is in high impedance mode (HIZ) with REGN LDO off. The
device draws less than IVBUS_HIZ from VBUS during HIZ state. The battery powers up the system when the device
is in HIZ.
9.2.3.2 Poor Source Qualification
After REGN LDO powers up, the device checks the current capability of the input source. The input source has
to meet the following requirements in order to start the buck converter.
1. VBUS voltage below VACOV
2. VBUS voltage above VVBUSMIN when pulling IBADSRC (typical 30mA)
Once the input source passes all the conditions above, the status register bit VBUS_GD is set high and the INT
pin is pulsed to signal to the host. If the device fails the poor source detection, it repeats poor source qualification
every 2 seconds.
9.2.3.3 Input Source Type Detection
After the VBUS_GD bit is set and REGN LDO is powered, the charger device runs Input Source Type Detection
when AUTO_DPDM_EN bit is set.
版权 © 2016–2017, Texas Instruments Incorporated
17
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
Feature Description (接下页)
The bq25898D follows the USB Battery Charging Specification 1.2 (BC1.2) and to detect input source
(SDP/CDP/DCP) and non-standard adapter through USB D+/D- lines. In addition, when USB DCP is detected, it
initiates adjustable high voltage adapter handshake on D+/D-. The device supports MaxCharge™ handshake
when MAXC_EN or HVDCP_EN is set. The bq25898 sets input current limit through PSEL and OTG pins.
After input source type detection, an INT pulse is asserted to the host. In addition, the following registers and pin
are changed:
1. Input Current Limit (IINLIM) register is changed to set current limit
2. PG_STAT bit is set
3. PG pin goes low (bq25898)
The host can over-write IINLIM register to change the input current limit if needed. The charger input current is
always limited by the lower of IINLIM register or ILIM pin at all-time regardless of Input Current Optimizer (ICO) is
enable or disabled.
When AUTO_DPDM_EN is disabled, the Input Source Type Detection is bypassed. The Input Current Limit
(IINLIM) register, VBUS_STAT, and SPD_STAT bits are unchanged from previous values.
9.2.3.3.1 D+/D– Detection Sets Input Current Limit (bq25898D)
The bq25898D contains a D+/D– based input source detection to set the input current limit automatically. The
D+/D- detection includes standard USB BC1.2, non-standard adapter, and adjustable high voltage adapter
detections. When input source is plugged-in, the device starts standard USB BC1.2 detections. The USB BC1.2
is capable to identify Standard Downstream Port (SDP), Charging Downstream Port (CDP), and Dedicated
Charging Port (DCP). When the Data Contact Detection (DCD) timer of 500ms is expired, the non-standard
adapter detection is applied to set the input current limit.
When DCP is detected, the device initates adjustable high voltage adapter handshake including MaxCharge™,
etc. The handshake connects combinations of voltage source(s) and/or current sink on D+/D- to signal input
source to raise output voltage from 5 V to 9 V / 12 V. The adjustable high voltage adapter handshake can be
disabled by clearing MAXC_EN and/or HVDCP_EN bits .
Non-Standard Adapter
(Divider 1: 2.1A)
(Divider 2: 2A)
(Divider 3: 1A)
Non-Standard
Adapter
(Divider 4: 2.4A)
Adapter Plug-in
USB BC1.2
Detection
Ajustable High Voltage Adapter
Handshake
or
EN_DPDM
SDP (USB500)
(500mA)
CDP
(1.5A)
MaxCharge™ Apapter
(1.5A)
DCP
(3.25A)
图 11. USB D+/D- Detection
18
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
表 1. Non-Standard Adapter Detection
NON-STANDARD
ADAPTER
D+ THRESHOLD
D- THRESHOLD
INPUT CURRENT LIMIT
Divider 1
Divider 2
Divider 3
Divider 4
VD+ within V2P7_VTH
VD+ within V1P2_VTH
VD+ within V2P0_VTH
VD+ within V2P7_VTH
VD- within V2P0_VTH
VD- within V1P2_VTH
VD- within V2P7_VTH
VD- within V2P7_VTH
2.1A
2A
1A
2.4A
表 2. Adjustable High Voltage Adapter D+/D- Output Configurations
ADJUSTABLE HIGH VOLTAGE
D+
D-
OUTPUT
HANDSHAKE
MaxCharge (12V)
MaxCharge (9V)
I1P6MA_ISINK
V3p45_VSRC
V3p45_VSRC
I1P6MA_ISINK
12 V
9 V
After the Input Source Type Detection is done, an INT pulse is asserted to the host. In addition, the following
registers including Input Current Limit register (IINLIM), VBUS_STAT, and SDP_STAT are updated as below:
表 3. bq25898D Result
INPUT CURRENT LIMIT
D+/D- DETECTION
SDP_STAT
VBUS_STAT
(IINLIM)
500 mA
1.5 A
USB SDP (USB500)
USB CDP
1
1
1
1
1
1
1
1
1
001
010
011
110
110
110
110
100
101
USB DCP
3.25 A
1 A
Divider 3
Divider 1
2.1 A
Divider 4
2.4 A
Divider 2
2 A
MaxCharge
Unknown Adapter
1.5 A
500 mA
9.2.3.3.2 PSEL Pin Sets Input Current Limit (bq25898)
The bq25898 has PSEL interface for input current limit setting to interface with USB PHY. It directly takes the
USB PHY device output to decide whether the input is USB host or charging port. To implement USB100 in the
system, the host can enter HiZ mode by setting EN_HIZ bit after 2 min charging with 500 mA input current limit.
表 4. bq25898 Result
INPUT CURRENT LIMIT
INPUT DETECTION
BAT VOLTAGE
PSEL PIN
SDP_STAT
VBUS_STAT
(IINLIM)
500 mA
3.25 A
USB SDP (USB500)
Adapter
X
X
High
Low
1
1
001
010
9.2.3.3.3 Force Input Current Limit Detection
In host mode, the host can force the device to run by setting FORCE_DPDM bit. After the detection is completed,
FORCE_DPDM bit returns to 0 by itself and Input Result is updated.
9.2.3.4 Input Voltage Limit Threshold Setting (VINDPM Threshold)
The device supports wide range of input voltage limit (3.9 V – 14 V) for high voltage charging and provides two
methods to set Input Voltage Limit (VINDPM) threshold to facilitate autonomous detection.
1. Absolute VINDPM (FORCE_VINDPM=1)
By setting FORCE_VINDPM bit to 1, the VINDPM threshold setting algorithm is disabled. Register VINDPM
is writable and allows host to set the absolute threshold of VINDPM function.
2. Relative VINDPM based on VINDPM_OS registers (FORCE_VINDPM=0) (Default)
版权 © 2016–2017, Texas Instruments Incorporated
19
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
When FORCE_VINDPM bit is 0 (default), the VINDPM threshold setting algorithm is enabled. The VINDPM
register is read only and the charger controls the register by using VINDPM Threshold setting algorithm. The
algorithm allows a wide range of adapter (VVBUS_OP) to be used with flexible VINDPM threshold.
After Input Voltage Limit Threshold is set, an INT pulse is generated to signal to the host.
9.2.3.5 Converter Power-Up
After the input current limit is set, the converter is enabled and the HSFET and LSFET start switching. If battery
charging is disabled, BATFET turns off. Otherwise, BATFET stays on to charge the battery.
The device provides soft-start when system rail is ramped up. When the system rail is below 2.2 V, the input
current limit is forced to the lower of 200 mA or IINLIM register setting. After the system rises above 2.2 V, the
device limits input current to the lower value of ILIM pin and IILIM register (ICO_EN = 0) or IDPM_LIM register
(ICO_EN = 1).
As a battery charger, the device deploys a highly efficient 1.5 MHz step-down switching regulator. The fixed
frequency oscillator keeps tight control of the switching frequency under all conditions of input voltage, battery
voltage, charge current and temperature, simplifying output filter design.
A type III compensation network allows using ceramic capacitors at the output of the converter. An internal saw-
tooth ramp is compared to the internal error control signal to vary the duty cycle of the converter. The ramp
height is proportional to the PMID voltage to cancel out any loop gain variation due to a change in input voltage.
In order to improve light-load efficiency, the device switches to PFM control at light load when battery is below
minimum system voltage setting or charging is disabled. During the PFM operation, the switching duty cycle is
set by the ratio of SYS and VBUS.
9.2.4 Input Current Optimizer (ICO)
The device provides innovative Input Current Optimizer (ICO) to identify maximum power point without overload
the input source. The algorithm automatically identify maximum input current limit of power source without
entering VINDPM to avoid input source overload.
This feature is enabled by default (ICO_EN=1) and can be disabled by setting ICO_EN bit to 0. After DCP or
MaxCharge type input source is detected based on the procedures previously described (Input Source Type
Detection ). The algorithm runs automatically when ICO_EN bit is set. The algorithm can also be forced to
execute by setting FORCE_ICO bit regardless of input source type detected.
The actual input current limit used by the Dynamic Power Management is reported in IDPM_LIM register while
Input Current Optimizer is enabled (ICO_EN = 1) or set by IINLIM register when the algorithm is disabled
(ICO_EN = 0). In addition, the current limit is clamped by ILIM pin unless EN_ILIM bit is 0 to disable ILIM pin
function.
9.2.5 Boost Mode Operation from Battery
The device supports boost converter operation to deliver power from the battery to other portable devices
through USB port. The boost mode output current rating meets the USB On-The-Go 500 mA (BOOST_LIM bits =
000) output requirement. The maximum output current is up to 2.4 A. The boost operation can be enabled if the
conditions are valid:
1. BAT above BATLOWV
2. VBUS less than BAT+VSLEEP (in sleep mode)
3. Boost mode operation is enabled (OTG pin HIGH and OTG_CONFIG bit =1)
4. Voltage at TS (thermistor) pin is within range configured by Boost Mode Temperature Monitor as configured
by BHOT and BCOLD bits
5. After 30 ms delay from boost mode enable
In boost mode, the device employs a 500 KHz or 1.5 MHz (selectable using BOOST_FREQ bit) step-up
switching regulator based on system requirements. To avoid frequency change during boost mode operations,
write to boost frequency configuration bit (BOOST_FREQ) is ignored when OTG_CONFIG is set.
During boost mode, the status register VBUS_STAT bits is set to 111, the VBUS output is 5V by default
(selectable via BOOSTV register bits) and the output current can reach up to 2.4 A, selected via I2C
(BOOST_LIM bits). The boost output is maintained when BAT is above VOTG_BAT threshold.
20
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.2.6 Power Path Management
The device accommodates a wide range of input sources from USB, wall adapter, to car battery. The device
provides automatic power path selection to supply the system (SYS) from input source (VBUS), battery (BAT), or
both.
9.2.6.1 Narrow VDC Architecture
The device deploys Narrow VDC architecture (NVDC) with BATFET separating system from battery. The
minimum system voltage is set by SYS_MIN bits. Even with a fully depleted battery, the system is regulated
above the minimum system voltage (default 3.5 V).
When the battery is below minimum system voltage setting, the BATFET operates in linear mode (LDO mode),
and the system is regulated above the minimum system voltage setting. As the battery voltage rises above the
minimum system voltage, BATFET is fully on and the voltage difference between the system and battery is the
VDS of BATFET. The status register VSYS_STAT bit goes high when the system is in minimum system voltage
regulation.
4.4
Minimum System Voltage
SYS (Charge Disabled)
SYS (Charge Enabled)
4.2
4
3.8
3.6
3.4
2.7
2.9
3.1
3.3
3.5
3.7
3.9
4.1
4.3
BAT (V)
D011
图 12. V(SYS) vs V(BAT)
9.2.6.2 Dynamic Power Management
To meet maximum current limit in USB spec and avoid over loading the adapter, the device features Dynamic
Power Management (DPM), which continuously monitors the input current and input voltage. When input source
is over-loaded, either the current exceeds the input current limit (IINLIM or IDPM_LIM) or the voltage falls below
the input voltage limit (VINDPM). The device then reduces the charge current until the input current falls below
the input current limit and the input voltage rises above the input voltage limit.
When the charge current is reduced to zero, but the input source is still overloaded, the system voltage starts to
drop. Once the system voltage falls below the battery voltage, the device automatically enters the Supplement
Mode where the BATFET turns on and battery starts discharging so that the system is supported from both the
input source and battery.
During DPM mode, the status register bits VDPM_STAT (VINDPM) and/or IDPM_STAT (IINDPM) is/are set high.
图 13 shows the DPM response with 9V/1.2A adapter, 3.2-V battery, 2.8-A charge current and 3.4-V minimum
system voltage setting.
版权 © 2016–2017, Texas Instruments Incorporated
21
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
ëoltage
VBUS
SYS
BAT
3.6V
3.4V
3.2V
3.18V
/urrent
4A
ICHG
IIN
3.2A
2.8A
ISYS
DPM
1.2A
1.0A
0.5A
-0.6A
DPM
Supplement
图 13. DPM Response
9.2.6.3 Supplement Mode
When the system voltage falls below the battery voltage, the BATFET turns on and the BATFET gate is
regulated the gate drive of BATFET so that the minimum BATFET VDS stays at 30 mV when the current is low.
This prevents oscillation from entering and exiting the Supplement Mode. As the discharge current increases, the
BATFET gate is regulated with a higher voltage to reduce RDS(ON) until the BATFET is in full conduction. At this
point onwards, the BATFET VDS linearly increases with discharge current. 图 14 shows the V-I curve of the
BATFET gate regulation operation. BATFET turns off to exit Supplement Mode when the battery is below battery
depletion threshold.
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
5
10 15 20 25 30 35 40 45 50 55
V(BAT_SYS) (mV)
D010
图 14. BATFET V-I Curve
9.2.7 Battery Charging Management
The device charges 1-cell Li-Ion battery with up to 4-A charge current for high capacity battery. The 5-mΩ
BATFET improves charging efficiency and minimize the voltage drop during discharging.
9.2.7.1 Autonomous Charging Cycle
With battery charging enabled (CHG_CONFIG bit = 1 and CE pin is low), the device autonomously completes a
charging cycle without host involvement. The device default charging parameters are listed in 表 5. The host can
always control the charging operations and optimize the charging parameters by writing to the corresponding
registers through I2C.
22
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
表 5. Charging Parameter Default Setting
DEFAULT MODE
Charging Voltage
Charging Current
bq25898D
4.208 V
2.048 A
128 mA
256 mA
JEITA
bq25898
4.208 V
2.048 A
128 mA
256 mA
JEITA
Pre-charge Current
Termination Current
Temperature Profile
Safety Timer
12 hour
12 hour
A new charge cycle starts when the following conditions are valid:
•
•
•
•
•
Converter starts
Battery charging is enabled by setting CHG_CONFIG bit, /CE pin is low and ICHG register is not 0 mA
No thermistor fault on TS pin
No safety timer fault
BATFET is not forced to turn off (BATFET_DIS bit = 0)
The charger device automatically terminates the charging cycle when the charging current is below termination
threshold, charge voltage is above recharge threshold, and device not in DPM mode or thermal regulation. When
a full battery voltage is discharged below recharge threshold (threshold selectable via VRECHG bit), the device
automatically starts a new charging cycle. After the charge is done, either toggle CE pin or CHG_CONFIG bit
can initiate a new charging cycle.
The STAT output indicates the charging status of charging (LOW), charging complete or charge disable (HIGH)
or charging fault (Blinking). The STAT output can be disabled by setting STAT_DIS bit. In addition, the status
register (CHRG_STAT) indicates the different charging phases: 00-charging disable, 01-precharge, 10-fast
charge (constant current) and constant voltage mode, 11-charging done. Once a charging cycle is completed, an
INT is asserted to notify the host.
9.2.7.2 Battery Charging Profile
The device charges the battery in three phases: preconditioning, constant current and constant voltage. At the
beginning of a charging cycle, the device checks the battery voltage and regulates current / voltage.
表 6. Charging Current Setting
VBAT
< 2 V
CHARGING CURRENT
IBATSHORT
REG DEFAULT SETTING
CHRG_STAT
–
01
01
10
2 V – 3 V
> 3 V
IPRECHG
0 mA (precharge disabled)
2048 mA
ICHG
版权 © 2016–2017, Texas Instruments Incorporated
23
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
If the charger device is in DPM regulation or thermal regulation during charging, the charging current can be less
than the programmed value. In this case, termination is temporarily disabled and the charging safety timer is
counted at half the clock rate.
wegulation ëoltage
(3.84ë t 4.608ë)
ꢀattery ëoltage
Cast /harge /urrent
(128m!-4032m!)
/harge /urrent
ë
ꢀ!Ç_[ꢁíë (2.8ëꢂ3ë
or 2.6ëꢂ2.8ë)
ë
ꢀ!Ç_{IꢁwÇ (2ë)
L
ꢃw9/I!wD9 (64m!-1024m!)
Ç9wꢄLb!ÇLꢁb (64m!-1024m!)
ꢀ!Ç{IꢁwÇ (100m!)
L
L
Cast /harge and ëoltage wegulation
Çrickle /harge
ꢃre-charge
{afety Çimer
9xpiration
图 15. Battery Charging Profile
9.2.7.3 Charging Termination
The device terminates a charge cycle when the battery voltage is above recharge threshold, and the current is
below termination current. After the charging cycle is completed, the BATFET turns off. The converter keeps
running to power the system, and BATFET can turn on again to engage Supplement Mode.
When termination occurs, the status register CHRG_STAT is set to 11, and an INT pulse is asserted to the host.
Termination is temporarily disabled when the charger device is in input current, voltage or thermal regulation.
Termination can be disabled by writing 0 to EN_TERM bit prior to charge termination.
9.2.7.4 Resistance Compensation (IRCOMP)
For high current charging system, resistance between charger output and battery cell terminal such as board
routing, connector, MOSFETs and sense resistor can force the charging process to move from constant current
to constant voltage too early and increase charge time. To speed up the charging cycle, the device provides
resistance compensation (IRCOMP) feature which can extend the constant current charge time to delivery
maximum power to battery.
The device allows the host to compensate for the resistance by increasing the voltage regulation set point based
on actual charge current and the resistance as shown below. For safe operation, the host should set the
maximum allowed regulation voltage register (VCLAMP) and the minimum resistance compensation (BATCOMP).
VREG_ACTUAL = VREG + min(ICHRG_ACTUAL x BATCOMP, VCLAMP
)
(1)
9.2.7.5 Thermistor Qualification
9.2.7.5.1 JEITA Guideline Compliance in Charge Mode
To improve the safety of charging Li-ion batteries, JEITA guideline was released on April 20, 2007. The guideline
emphasized the importance of avoiding a high charge current and high charge voltage at certain low and high
temperature ranges.
24
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
The device continuously monitors battery temperature by measuring the voltage between the TS pins and
ground, typically determined by a negative temperature coefficient thermistor (NTC) and an external voltage
divider. The device compares this voltage against its internal thresholds to determine if charging is allowed. To
initiate a charge cycle, the voltage on TS pin must be within the VT1 to VT5 thresholds. If TS voltage exceeds the
T1–T5 range, the controller suspends charging and waits until the battery temperature is within the T1 to T5
range. At cool temperature (T1–T2), JEITA recommends the charge current to be reduced to at least half of the
charge current or lower. At warm temperature (T3–T5), JEITA recommends charge voltage below nominal
charge voltage.
The device provides flexible voltage/current settings beyond the JEITA requirement. The voltage setting at warm
temperature (T3–T5) can be 200 mV below charge voltage (JEITA_VSET=0). The current setting at cool
temperature (T1–T2) can be further reduced to 20% or 50% of fast charge current (JEITA_ISET bit).
REGN
bq25898x
RT1
TS
RTH
RT2
103AT
图 16. TS Resistor Network
VREG
VREG - 200 mV
图 17. Charging Values
Assuming a 103AT NTC thermistor on the battery pack as shown in 图 16, the value RT1 and RT2 can be
determined by using 公式 2:
1
1
æ
ö
VVREGN ´RTHCOLD ´RTHHOT
´
-
VT1 VT5
ç
÷
è
ø
RT2 =
V
V
æ
ö
æ
ö
VREGN
VREGN
RTHHOT
´
-1 - RTHCOLD
´
ç
-1
÷
ç
÷
VT5
VT1
è
ø
è
ø
VVREGN
VT1
-1
RT1=
1
1
+
RT2 RTHCOLD
(2)
25
Select 0°C to 60°C range for Li-ion or Li-polymer battery,
RTHT1 = 27.28 kΩ
RTHT5 = 3.02 kΩ
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
RT1 = 5.24 kΩ
RT2 = 30.31 kΩ
During JEITA cool, the bq25898x terminates when the charge current has reached 20% or 50% of termination
current setting, depending on the JT_IREDUCE bit. During JEITA warm, the bq25898x terminates when the
charge current reaches the termination current setting.
9.2.7.5.2 Cold/Hot Temperature Window in Boost Mode
For battery protection during boost mode, the device monitors the battery temperature to be within the VBCOLD1 to
VBHOT2 thresholds unless boost mode temperature is disabled by setting BHOT bits to 11. When temperature is
outside of the temperature thresholds, the boost mode is suspended. Once temperature is within thresholds, the
boost mode is recovered.
Temperature Range to
Boost
VREGN
Boost Disable
V
BCOLDx
(-
20ºC)
Boost Enable
V
BHOTx
(65ºC)
Boost Disable
AGND
图 18. TS Pin Thermistor Sense Thresholds in Boost Mode
9.2.7.6 Charging Safety Timer
The device has built-in safety timer to prevent extended charging cycle due to abnormal battery conditions. The
safety timer is 4 hours when the battery is below VBATLOWV threshold. The user can program fast charge safety
timer through I2C (CHG_TIMER bits). When safety timer expires, the fault register CHRG_FAULT bits are set to
11 and an INT is asserted to the host. The safety timer feature can be disabled via I2C by setting EN_TIMER bit.
During input voltage, current or thermal regulation, the safety timer counts at half clock rate as the actual charge
current is likely to be below the register setting. For example, if the charger is in input current regulation
(IDPM_STAT = 1) throughout the whole charging cycle, and the safety time is set to 5 hours, the safety timer will
expire in 10 hours. This half clock rate feature can be disabled by writing 0 to TMR2X_EN bit.
9.2.8 Battery Monitor
The device includes a battery monitor to provide measurements of VBUS voltage, battery voltage, system
voltage, thermistor ratio, and charging current, and charging current based on the device’s modes of operation.
The measurements are reported in Battery Monitor Registers (REG0E-REG12). The battery monitor can be
configured as two conversion modes by using CONV_RATE bit: one-shot conversion (default) and 1 second
continuous conversion.
For one-shot conversion (CONV_RATE = 0), the CONV_START bit can be set to start the conversion. During the
conversion, the CONV_START is set and it is cleared by the device when conversion is completed. The
conversion result is ready after tCONV (maximum 1 second).
For continuous conversion (CONV_RATE = 1), the CONV_RATE bit can be set to initiate the conversion. During
active conversion, the CONV_START is set to indicate conversion is in progress. The battery monitor provides
conversion result every 1 second automatically. The battery monitor exits continuous conversion mode when
CONV_RATE is cleared.
26
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
When battery monitor is active, the REGN power is enabled and can increase device quiescent current.
表 7. Battery Monitor Modes of Operation
MODES OF OPERATION
PARAMETER
REGISTER
CHARGE
MODE
DISABLE CHARGE
MODE
BATTERY ONLY
MODE
BOOST MODE
Battery Voltage (VBAT
)
REG0E
REG0F
REG10
REG11
REG12
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
NA
Yes
Yes
Yes
Yes
NA
Yes
Yes
Yes
NA
System Voltage (VSYS
Temperature (TS) Voltage (VTS
VBUS Voltage (VVBUS
Charge Current (IBAT
)
)
)
)
NA
9.2.9 Status Outputs (PG, STAT, and INT)
9.2.9.1 Power Good Indicator (PG)
In bq25898, the PG goes LOW to indicate a good input source when:
1. VBUS above VVBUS_UVLO
2. VBUS above battery (not in sleep)
3. VBUS below VACOV threshold
4. VBUS above VVBUSMIN (typical 3.8 V) when IBADSRC (typical 30 mA) current is applied (not a poor source)
5. Completed Input Source Type Detection
9.2.9.2 Charging Status Indicator (STAT)
The device indicates charging state on the open drain STAT pin. The STAT pin can drive LED as shown in 图
49. The STAT pin function can be disable by setting STAT_DIS bit.
表 8. STAT Pin State
CHARGING STATE
Charging in progress (including recharge)
STAT INDICATOR
LOW
HIGH
HIGH
Charging complete
Sleep mode, charge disable
Charge suspend (Input overvoltage, TS fault, timer fault, input or system overvoltage)
Boost Mode suspend (due to TS Fault)
blinking at 1 Hz
9.2.9.3 Interrupt to Host (INT)
In some applications, the host does not always monitor the charger operation. The INT notifies the system on the
device operation. The following events will generate 256-µs INT pulse.
•
•
USB/adapter source identified (through PSEL or DPDM detection, with OTG pin)
Good input source detected
–
–
–
VBUS above battery (not in sleep)
VBUS below VACOV threshold
VBUS above VVBUSMIN (typical 3.8 V) when IBADSRC (typical 30 mA) current is applied (not a poor source)
•
•
•
Input removed
Charge Complete
Any FAULT event in REG0C
When a fault occurs, the charger device sends out INT and keeps the fault state in REG0C until the host reads
the fault register. Before the host reads REG0C and all the faults are cleared, the charger device would not send
any INT upon new faults. To read the current fault status, the host has to read REG0C two times consecutively.
The 1st read reports the pre-existing fault register status and the 2nd read reports the current fault register status.
版权 © 2016–2017, Texas Instruments Incorporated
27
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.2.10 BATFET (Q4) Control
9.2.10.1 BATFET Disable Mode (Shipping Mode)
To extend battery life and minimize power when system is powered off during system idle, shipping, or storage,
the device can turn off BATFET so that the system voltage is zero to minimize the battery leakage current. When
the host set BATFET_DIS bit, the charger can turn off BATFET immediately or delay by tSM_DLY as configurated
by BATFET_DLY bit.
9.2.10.2 BATFET Enable (Exit Shipping Mode)
When the BATFET is disabled (in shipping mode) and indicated by setting BATFET_DIS, one of the following
events can enable BATFET to restore system power:
1. Plug in adapter
2. Clear BATFET_DIS bit
3. Set REG_RST bit to reset all registers including BATFET_DIS bit to default (0)
4. A logic high to low transition on QON pin with tSHIPMODE deglitch time to enable BATFET to exit shipping
mode
9.2.10.3 BATFET Full System Reset
The BATFET functions as a load switch between battery and system when input source is not plugged-in. By
changing the state of BATFET from off to on, system connects to SYS can be effectively have a power-on-reset.
The QON pin supports push-button interface to reset system power without host by change the state of BATFET.
When the QON pin is driven to logic low for tQON_RST (typical 15 seconds) while input source is not plugged in
and BATFET is enabled (BATFET_DIS=0), the BATFET is turned off for tBATFET_RST and then it is re-enabled to
reset system power. This function can be disabled by setting BATFET_RST_EN bit to 0.
9.2.11 Current Pulse Control Protocol
The device provides the control to generate the VBUS current pulse protocol to communicate with adjustable
high voltage adapter in order to signal adapter to increase or decrease output voltage. To enable the interface,
the EN_PUMPX bit must be set. Then the host can select the increase/decrease voltage pulse by setting one of
the PUMPX_UP or PUMPX_DN bit (but not both) to start the VBUS current pulse sequence. During the current
pulse sequence, the PUMPX_UP and PUMPX_DN bits are set to indicate pulse sequence is in progress and the
device pulses the input current limit between current limit set forth by IINLIM or IDPM_LIM register and the
100mA current limit (IINDPM100_ACC). When the pulse sequence is completed, the input current limit is returned to
value set by IINLIM or IDPM_LIM register and the PUMPX_UP or PUMPX_DN bit is cleared. In addition, the
EN_PUMPX can be cleared during the current pulse sequence to terminate the sequence and force charger to
return to input current limit as set forth by the IINLIM or IDPM_LIM register immediately. When EN_PUMPX bit is
low, write to PUMPX_UP and PUMPX_DN bit would be ignored and have no effect on VBUS current limit.
9.2.12 Input Current Limit on ILIM
For safe operation, the device has an additional hardware pin on ILIM to limit maximum input current on ILIM pin.
The input maximum current is set by a resistor from ILIM pin to ground as:
K
ILIM
I
=
INMAX
R
ILIM
(3)
The actual input current limit is the lower value between ILIM setting and register setting (IINLIM). For example, if
the register setting is 111111 for 3.25 A, and ILIM has a 232-Ω resistor (KILIM = 350 max.) to ground for 1.5 A,
the input current limit is 1.5 A. ILIM pin can be used to set the input current limit rather than the register settings
when EN_ILIM bit is set. The device regulates ILIM pin at 0.8 V. If ILIM voltage exceeds 0.8 V, the device enters
input current regulation (Refer to Dynamic Power Management section).
The ILIM pin can also be used to monitor input current when EN_ILIM is enabled. The voltage on ILIM pin is
proportional to the input current. ILIM pin can be used to monitor the input current following 公式 4:
K
x V
ILIM
ILIM
I
=
IN
R
x 0.8 V
ILIM
(4)
28
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
For example, if ILIM pin is set with 260-Ω resistor, and the ILIM voltage is 0.4 V, the actual input current 0.557 A
- 0.67 A (based on KILM specified). If ILIM pin is open, the input current is limited to zero since ILIM voltage
floats above 0.8 V. If ILIM pin is short, the input current limit is set by the register.
The ILIM pin function can be disabled by setting EN_ILIM bit to 0. When the pin is disabled, both input current
limit function and monitoring function are not available.
9.2.13 Thermal Regulation and Thermal Shutdown
9.2.13.1 Thermal Protection in Buck Mode
The device monitors the internal junction temperature TJ to avoid overheat the chip and limits the IC surface
temperature in buck mode. When the internal junction temperature exceeds the preset thermal regulation limit
(TREG bits), the device lowers down the charge current. The wide thermal regulation range from 60ºC to 120ºC
allows the user to optimize the system thermal performance.
During thermal regulation, the actual charging current is usually below the programmed battery charging current.
Therefore, termination is disabled, the safety timer runs at half the clock rate, and the status register
THERM_STAT bit goes high.
Additionally, the device has thermal shutdown to turn off the converter and BATFET when IC surface
temperature exceeds TSHUT. The fault register CHRG_FAULT is set to 10 and an INT is asserted to the host. The
BATFET and converter is enabled to recover when IC temperature is below TSHUT_HYS
.
9.2.13.1.1 Thermal Protection in Boost Mode
The device monitors the internal junction temperature to provide thermal shutdown during boost mode. When IC
surface temperature exceeds TSHUT, the boost mode is disabled (converter is turned off) by setting
OTG_CONFIG bit low and BATFET is turned off. When IC surface temperature is below TSHUT_HYS, the BATFET
is enabled automatically to allow system to restore and the host can re-enable OTG_CONFIG bit to recover.
9.2.14 Voltage and Current Monitoring in Buck and Boost Mode
9.2.14.1 Voltage and Current Monitoring in Buck Mode
The device closely monitors the input and system voltage, as well as HSFET current for safe buck and boost
mode operations.
9.2.14.1.1 Input Overvoltage (ACOV)
The input voltage for buck mode operation is VVBUS_OP. If VBUS voltage exceeds VACOV, the device stops
switching immediately. During input over voltage (ACOV), the fault register CHRG_FAULT bits sets to 01. An INT
is asserted to the host.
9.2.14.1.2 System Overvoltage Protection (SYSOVP)
The charger device clamps the system voltage during load transient so that the components connect to system
would not be damaged due to high voltage. When SYSOVP is detected, the converter stops immediately to
clamp the overshoot.
9.2.14.2 Voltage and Current Monitoring in Boost Mode
The device closely monitors the VBUS voltage, as well as RBFET and LSFET current to ensure safe boost mode
operation.
9.2.14.2.1 VBUS Overcurrent Protection
The charger device closely monitors the RBFET (Q1), and LSFET (Q3) current to ensure safe boost mode
operation. During overcurrent condition when output current exceed (IOTG_OCP) the device operates in hiccup
mode for protection. While in hiccup mode cycle, the device turns off RBFET for tOTG_OCP_OFF (30 ms typical) and
turns on RBFET for tOTG_OCP_ON (250 µs typical) in an attempt to restart. If the overcurrent condition is removed,
the boost converter returns to normal operation. When overcurrent condition continues to exist, the device
repeats the hiccup cycle until overcurrent condition is removed. When overcurrent condition is detected the fault
register bit BOOST_FAULT is set high to indicate fault in boost operation. An INT is also asserted to the host.
版权 © 2016–2017, Texas Instruments Incorporated
29
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.2.14.2.2 Boost Mode Overvoltage Protection
When the VBUS voltage rises above regulation target and exceeds VOTG_OVP, the device enters overvoltage
protection which stops switching, clears OTG_CONFIG bit and exits boost mode. During the overvoltage
duration, the fault register bit (BOOST_FAULT) is set high to indicate fault in boost operation. An INT is also
asserted to the host.
9.2.15 Battery Protection
9.2.15.1 Battery Overvoltage Protection (BATOVP)
The battery overvoltage limit is clamped at 4% above the battery regulation voltage. When battery over voltage
occurs, the charger device immediately disables charge. The fault register BAT_FAULT bit goes high and an INT
is asserted to the host.
9.2.15.2 Battery Over-Discharge Protection
When battery is discharged below VBAT_DPL, the BATFET is turned off to protect battery from over discharge. To
recover from over-discharge, an input source is required at VBUS. When an input source is plugged in, the
BATFET turns on. Thy is charged with IBATSHORT (typically 100 mA) current when the VBAT < VSHORT, or
precharge current as set in IPRECHG register when the battery voltage is between VSHORT and VBATLOWV
.
9.2.15.3 System Overcurrent Protection
When the system is shorted or significantly overloaded (IBAT > IBATOP) so that its current exceeds the overcurrent
limit, the device latches off BATFET. Section BATFET Enable (Exit Shipping Mode) can reset the latch-off
condition and turn on BATFET.
9.2.16 Serial Interface
The device uses I2C compatible interface for flexible charging parameter programming and instantaneous device
status reporting. I2C is a bi-directional 2-wire serial interface. Only two open-drain bus lines are required: a serial
data line (SDA) and a serial clock line (SCL). Devices can be considered as masters or slaves when performing
data transfers. A master is the device which initiates a data transfer on the bus and generates the clock signals
to permit that transfer. At that time, any device addressed is considered a slave.
The device operates as a slave device with address 6BH, receiving control inputs from the master device like
micro controller or a digital signal processor through REG00-REG14. Register read beyond REG14 (0x14)
returns 0xFF. The I2C interface supports both standard mode (up to 100 kbits), and fast mode (up to 400 kbits).
When the bus is free, both lines are HIGH. The SDA and SCL pins are open drain and must be connected to the
positive supply voltage via a current source or pull-up resistor.
9.2.16.1 Data Validity
The data on the SDA line must be stable during the HIGH period of the clock. The HIGH or LOW state of the
data line can only change when the clock signal on the SCL line is LOW. One clock pulse is generated for each
data bit transferred.
SDA
SCL
Change
of data
allowed
Data line stable;
Data valid
图 19. Bit Transfer on the I2C Bus
30
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.2.16.2 START and STOP Conditions
All transactions begin with a START (S) and can be terminated by a STOP (P). A HIGH to LOW transition on the
SDA line while SCl is HIGH defines a START condition. A LOW to HIGH transition on the SDA line when the
SCL is HIGH defines a STOP condition.
START and STOP conditions are always generated by the master. The bus is considered busy after the START
condition, and free after the STOP condition.
{5!
{/[
{5!
{/[
{Çht (t)
{Ç!wÇ ({)
图 20. START and STOP conditions
9.2.16.3 Byte Format
Every byte on the SDA line must be 8 bits long. The number of bytes to be transmitted per transfer is
unrestricted. Each byte has to be followed by an Acknowledge bit. Data is transferred with the Most Significant
Bit (MSB) first. If a slave cannot receive or transmit another complete byte of data until it has performed some
other function, it can hold the clock line SCL low to force the master into a wait state (clock stretching). Data
transfer then continues when the slave is ready for another byte of data and release the clock line SCL.
!cknoꢁledgement
signal from revceiver
!cknoꢁledgement
signal from slave
ꢀ{.
1
ꢂ or
{r
{ or {r
2
7
8
9
!/Y
1
2
8
9
!/Y
{Ç!wÇ or
wepeated
{Ç!wÇ
{Çhꢂ or
wepeated
{Ç!wÇ
图 21. Data Transfer on the I2C Bus
9.2.16.4 Acknowledge (ACK) and Not Acknowledge (NACK)
The acknowledge takes place after every byte. The acknowledge bit allows the receiver to signal the transmitter
that the byte was successfully received and another byte may be sent. All clock pulses, including the
acknowledge 9th clock pulse, are generated by the master.
The transmitter releases the SDA line during the acknowledge clock pulse so the receiver can pull the SDA line
LOW and it remains stable LOW during the HIGH period of this clock pulse.
When SDA remains HIGH during the 9th clock pulse, this is the Not Acknowledge signal. The master can then
generate either a STOP to abort the transfer or a repeated START to start a new transfer.
9.2.16.5 Slave Address and Data Direction Bit
After the START, a slave address is sent. This address is 7 bits long followed by the eighth bit as a data direction
bit (bit R/W). A zero indicates a transmission (WRITE) and a one indicates a request for data (READ).
版权 © 2016–2017, Texas Instruments Incorporated
31
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
{5!
{
8
9
8
9
8
9
t
{/[
1-7
1-7
1-7
{Ç!wÇ
!55wꢀ{{
wꢁí !/Y
5!Ç!
!/Y
5!Ç!
!/Y
{Çht
图 22. Complete Data Transfer
9.2.16.6 Single Read and Write
1
8
1
1
7
1
0
1
1
8
Slave Address
ACK
Reg Addr
ACK
P
S
ACK
Data Addr
图 23. Single Write
1
8
1
1
1
7
1
0
1
1
1
7
Slave Address
ACK
Reg Addr
ACK
S
S
ACK
Slave Address
1
1
8
P
Data
NCK
图 24. Single Read
If the register address is not defined, the charger IC send back NACK and go back to the idle state.
9.2.16.7 Multi-Read and Multi-Write
The charger device supports multi-read and multi-write on REG00 through REG14 except REG0C.
图 25. Multi-Write
图 26. Multi-Read
32
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
REG0C is a fault register. It keeps all the fault information from last read until the host issues a new read. For
example, if Charge Safety Timer Expiration fault occurs but recovers later, the fault register REG0C reports the
fault when it is read the first time, but returns to normal when it is read the second time. In order to get the fault
information at present, the host has to read REG0C for the second time. The only exception is NTC_FAULT
which always reports the actual condition on the TS pin. In addition, REG0C does not support multi-read and
multi-write.
9.3 Device Functional Modes
9.3.1 Host Mode and Default Mode
The device is a host controlled charger, but it can operate in default mode without host management. In default
mode, the device can be used an autonomous charger with no host or while host is in sleep mode. When the
charger is in default mode, WATCHDOG_FAULT bit is HIGH. When the charger is in host mode,
WATCHDOG_FAULT bit is LOW.
After power-on-reset, the device starts in default mode with watchdog timer expired, or default mode. All the
registers are in the default settings.
In default mode, the device keeps charging the battery with 12-hour fast charging safety timer. At the end of the
12-hour, the charging is stopped and the buck converter continues to operate to supply system load. Any write
command to device transitions the charger from default mode to host mode. All the device parameters can be
programmed by the host. To keep the device in host mode, the host has to reset the watchdog timer by writing 1
to WD_RST bit before the watchdog timer expires (WATCHDOG_FAULT bit is set), or disable watchdog timer by
setting WATCHDOG bits=00.
When the watchdog timer (WATCHDOG_FAULT bit = 1) is expired, the device returns to default mode and all
registers are reset to default values except IINLIM, VINDPM, VINDPM_OS, BATFET_RST_EN, BATFET_DLY,
and BATFET_DIS bits.
thw
ꢀaꢁcꢂdog ꢁimer expired
weseꢁ regisꢁers
L2/ inꢁerface enabled
Iosꢁ ꢃode
{ꢁarꢁ ꢀaꢁcꢂdog ꢁimer
ò
L2/ íriꢁe?
Iosꢁ programs regisꢁers
ꢄ
5efaulꢁ ꢃode
weseꢁ ꢀaꢁcꢂdog ꢁimer
weseꢁ selecꢁive regisꢁers
ò
í5_w{Ç biꢁ = 1?
ꢄ
ò
ꢄ
L2/ íriꢁe?
ò
ꢄ
íaꢁcꢂdog Çimer
9xpired?
图 27. Watchdog Timer Flow Chart
版权 © 2016–2017, Texas Instruments Incorporated
33
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4 Register Map
I2C Slave Address: 6AH (1101010B + R/W) (bq25898D)
I2C Slave Address: 6BH (1101011B + R/W) (bq25898)
9.4.1 REG00
图 28. REG00
7
0
6
1
5
0
4
0
3
1
2
0
1
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 9. REG00
Bit
Field
Type
Reset
Description
Enable HIZ Mode
0 – Disable (default)
1 – Enable
by REG_RST
by Watchdog
7
EN_HIZ
R/W
Enable ILIM Pin
0 – Disable
1 – Enable (default: Enable ILIM pin (1))
by REG_RST
by Watchdog
6
EN_ILIM
R/W
5
4
3
2
1
IINLIM[5]
IINLIM[4]
IINLIM[3]
IINLIM[2]
IINLIM[1]
R/W
R/W
R/W
R/W
R/W
by REG_RST
by REG_RST
by REG_RST
by REG_RST
by REG_RST
1600mA
800mA
400mA
200mA
100mA
Input Current Limit bq25898D
USB Host SDP = 500mA
USB CDP = 1.5A
USB DCP = 3.25A
Adjustable High Voltage (MaxCharge) DCP = 1.5A
Unknown Adapter = 500mA
Non-Standard Adapter = 1A/2A/2.1A/2.4A
bq25898
PSEL= Hi (USB500) = 500mA
PSEL= Lo = 3.25A
0
IINLIM[0]
R/W
by REG_RST
50mA
34
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.4.2 REG01
图 29. REG01
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 10. REG01
Bit
7
Field
Type
R/W
R/W
Reset
Description
DPLUS_DAC[2]
DPLUS_DAC[1]
by Software
by Software
D+ Output Driver (default 000)
000 – HiZ
001 – 0V
6
010 – 0.6V
011 – 1.2V
100 – 2.0V
101 – 2.7V
5
DPLUS_DAC[0]
R/W
by Software
110 – 3.3V
111 – D+/D- Short (D+ and D- driver are disabled)
4
3
DMINUS_DAC[2]
DMINUS_DAC[1]
R/W
R/W
by Software
by Software
D- Output Driver (default 000)
000 – HiZ
001 – 0V
010 – 0.6V
011 – 1.2V
100 – 2.0V
2
DMINUS_DAC[0]
R/W
by Software
101 – 2.7V
110 or 111 – 3.3V
0 – Disable 12V for MaxCharge and HVDCP (default)
1 – Enable 12V for MaxCharge and HVDCP
1
0
EN_12V
R/W
R/W
by Software
by Software
0 – 400mA offset
1 – 600mA offset (default)
VDPM_OS[0]
版权 © 2016–2017, Texas Instruments Incorporated
35
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4.3 REG02
图 30. REG02
7
0
6
0
5
0
4
1
3
1
2
1
1
0
0
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 11. REG02
Bit
Field
Type
Reset
Description
ADC Conversion Start Control
0 – ADC conversion not active (default).
1 – Start ADC Conversion
This bit is read-only when CONV_RATE = 1. The bit stays high during
ADC conversion and during input source detection.
by REG_RST
by Watchdog
7
CONV_START
R/W
ADC Conversion Rate Selection
0 – One shot ADC conversion (default)
1 – Start 1s Continuous Conversion
by REG_RST
by Watchdog
6
5
CONV_RATE
R/W
R/W
Boost Mode Frequency Selection
0 – 1.5MHz (default)
1 – 500KHz
by REG_RST
by Watchdog
BOOST_FREQ
Note: Write to this bit is ignored when OTG_CONFIG is enabled.
Input Current Optimizer (ICO) Enable
0 – Disable ICO Algorithm
1 – Enable ICO Algorithm (default)
4
3
2
1
0
ICO_EN
R/W
R/W
R/W
R/W
R/W
by REG_RST
by REG_RST
by REG_RST
High Voltage DCP Enable (bq25898D only)
0 – Disable HVDCP handshake
1 – Enable HVDCP handshake (default)
HVDCP_EN
MAXC_EN
MaxCharge Adapter Enable (bq25898D only)
0 – Disable MaxCharge handshake
1 – Enable MaxCharge handshake (default)
Force D+/D- Detection
0 – Not in D+/D- or PSEL detection (default)
1 – Force D+/D- detection
by REG_RST
by Watchdog
FORCE_DPDM
AUTO_DPDM_EN
Automatic D+/D- Detection Enable
0 –Disable D+/D- or PSEL detection when VBUS is plugged-in
1 –Enable D+/D- or PEL detection when VBUS is plugged-in (default)
by REG_RST
36
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.4.4 REG03
图 31. REG03
7
0
6
0
5
0
4
1
3
1
2
0
1
1
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 12. REG03
Bit
Field
Type
Reset
Description
0 – Disabled,
VOK = 0
(default)
1. Adapter Plug-in VOK_OTG_EN = x and VOK = 1
2. OTG if VOK_OTG_EN = 1 ≥ VOK = 1 if
VOK_OTG_EN = 0 ≥ VOK = 0
VOK_OTG_EN (bq25898 only)
R/W
by Software
1 – Enabled,
VOK = 1
3. Battery Only (non-OTG) VOK_OTG_EN = x and
VOK = 0
1. Adaptor Plug-in DSEL= 1 when:
1) During AUTO_DPDM, FORCE_DPDM, DCP,
HVDCP, MaxCharge and FORCE_DSEL = x
or
7
0 – Allow DSEL
= 0 (default)
2) Other input source and FORCE_DSEL = 1 DSEL
FORCE_DSEL (bq25898D only)
R/W
R/W
by Software
1 – Force DSEL = 0 when other input source and FORCE_DSEL = 0
= 1
2. OTG if FORCE_DSEL = 1 ≥ DSEL = 1 if
FORCE_DSEL = 0 ≥ DSEL = 0
3. Battery only (non-OTG) DSEL = 0 and
FORCE_DSEL = x
I2C Watchdog Timer Reset
0 – Normal (default)
1 – Reset (Back to 0 after timer reset)
by Software
by Watchdog
6
WD_RST
Charger Configuration
Boost (OTG) Mode Configuration
0 – OTG Disable (default)
1 – OTG Enable
by REG_RST
by Watchdog
5
4
OTG_CONFIG
R/W
R/W
Charge Enable Configuration
0 - Charge Disable
1- Charge Enable (default)
by REG_RST
by Watchdog
CHG_CONFIG
Minimum System Voltage Limit
3
2
1
SYS_MIN[2]
SYS_MIN[1]
SYS_MIN[0]
R/W
R/W
R/W
by REG_RST
by REG_RST
by REG_RST
0.4V
0.2V
0.1V
Minimum System Voltage Limit
Offset: 3.0V
Range 3.0V-3.7V
Default: 3.5V (101)
0 – 2.9V BAT falling (default = 0)
1 – 2.5V BAT falling
0
MIN_VBAT_SEL
R/W
by REG_RST
版权 © 2016–2017, Texas Instruments Incorporated
37
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4.5 REG04
图 32. REG04
7
0
6
0
5
1
4
0
3
0
2
0
1
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 13. REG04
Bit
Field
Type
Reset
Description
Current pulse control Enable
0 - Disable Current pulse control (default)
1- Enable Current pulse control (PUMPX_UP and PUMPX_DN)
by REG_RST
by Watchdog
7
EN_PUMPX
R/W
by REG_RST
by Watchdog
6
5
4
3
2
1
0
ICHG[6]
ICHG[5]
ICHG[4]
ICHG[3]
ICHG[2]
ICHG[1]
ICHG[0]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
4096mA
by REG_RST
by Watchdog
2048mA
Fast Charge Current Limit
Offset: 0mA
Range: 0mA (0000000) – 4032mA (011111) Default:
2048mA (0100000)
Note:
ICHG=000000 (0mA) disables charge
ICHG > 011111 (4032mA) is clamped to register value
011111 (4032mA)
by REG_RST
by Watchdog
1024mA
512mA
256mA
128mA
64mA
by REG_RST
by Watchdog
by REG_RST
by Watchdog
by REG_RST
by Watchdog
by REG_RST
by Watchdog
38
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.4.6 REG05
图 33. REG05
7
0
6
0
5
0
4
1
3
0
2
0
1
1
0
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 14. REG05
Bit
Field
Type
Reset
Description
by REG_RST
by Watchdog
7
IPRECHG[3]
R/W
512mA
by REG_RST
by Watchdog
Precharge Current Limit
Offset: 64mA
Range: 64mA – 1024mA
6
5
4
3
2
1
0
IPRECHG[2]
IPRECHG[1]
IPRECHG[0]
ITERM[3]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
256mA
128mA
64mA
by REG_RST
by Watchdog
Default: 0mA when REG04[5:0] = 000000
by REG_RST
by Watchdog
by REG_RST
by Watchdog
512mA
256mA
128mA
64mA
by REG_RST
by Watchdog
Termination Current Limit
Offset: 64mA
Range: 64mA – 1024mA
Default: 256mA (0011)
ITERM[2]
by REG_RST
by Watchdog
ITERM[1]
by REG_RST
by Watchdog
ITERM[0]
版权 © 2016–2017, Texas Instruments Incorporated
39
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4.7 REG06
图 34. REG06
7
0
6
1
5
0
4
1
3
1
2
1
1
1
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 15. REG06
Bit
Field
Type
Reset
Description
by REG_RST
by Watchdog
7
VREG[5]
R/W
512mV
by REG_RST
by Watchdog
6
5
4
3
2
VREG[4]
VREG[3]
VREG[2]
VREG[1]
VREG[0]
R/W
R/W
R/W
R/W
R/W
256mV
128mV
64mV
32mV
16mV
Charge Voltage Limit
Offset: 3.840V
Range: 3.840V – 4.608V (110000)
Default: 4.208V (010111)
Note:
by REG_RST
by Watchdog
by REG_RST
by Watchdog
VREG > 110000 (4.608V) is clamped to register value
110000 (4.608V)
by REG_RST
by Watchdog
by REG_RST
by Watchdog
Battery Precharge to Fast Charge Threshold
0 – 2.8V
1 – 3.0V (default)
by REG_RST
by Watchdog
1
0
BATLOWV
VRECHG
R/W
R/W
Battery Recharge Threshold Offset
(below Charge Voltage Limit)
0 – 100mV (VRECHG) below VREG (REG06[7:2]) (default)
1 – 200mV (VRECHG) below VREG (REG06[7:2])
by REG_RST
by Watchdog
40
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.4.8 REG07
图 35. REG07
7
1
6
0
5
0
4
1
3
1
2
1
1
0
0
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 16. REG07
Bit
Field
Type
Reset
Description
Charging Termination Enable
0 – Disable
1 – Enable (default)
by REG_RST
by Watchdog
7
EN_TERM
R/W
STAT Pin Disable
0 – Enable STAT pin function (default)
1 – Disable STAT pin function
by REG_RST
by Watchdog
6
STAT_DIS
R/W
by REG_RST
by Watchdog
I2C Watchdog Timer Setting
00 – Disable watchdog timer
01 – 40s (default)
10 – 80s
5
4
WATCHDOG[1]
WATCHDOG[0]
R/W
R/W
by REG_RST
by Watchdog
11 – 160s
Charging Safety Timer Enable
0 – Disable
1 – Enable (default)
by REG_RST
by Watchdog
3
EN_TIMER
R/W
by REG_RST
by Watchdog
Fast Charge Timer Setting
00 – 5 hrs
01 – 8 hrs
10 – 12 hrs (default)
11 – 20 hrs
2
1
CHG_TIMER[1]
CHG_TIMER[0]
R/W
R/W
by REG_RST
by Watchdog
JEITA Low Temperature Current Setting
0 – 50% of ICHG (REG04[6:0])
1 – 20% of ICHG (REG04[6:0]) (default)
by REG_RST
by Watchdog
0
JEITA_ISET (0C-10C)
R/W
版权 © 2016–2017, Texas Instruments Incorporated
41
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4.9 REG08
图 36. REG08
7
0
6
0
5
0
4
0
3
0
2
0
1
1
0
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 17. REG08
Bit
Field
Type
Reset
Description
by REG_RST
by Watchdog
7
BAT_COMP[2]
R/W
80mΩ
IR Compensation Resistor Setting
Range: 0 – 140mΩ
Default: 0Ω (000) (i.e. Disable IRComp)
by REG_RST
by Watchdog
6
5
4
3
2
1
BAT_COMP[1]
BAT_COMP[0]
VCLAMP[2]
VCLAMP[1]
VCLAMP[0]
TREG[1]
R/W
R/W
R/W
R/W
R/W
R/W
40mΩ
20mΩ
128mV
64mV
32mV
by REG_RST
by Watchdog
by REG_RST
by Watchdog
IR Compensation Voltage Clamp
above VREG (REG06[7:2])
Offset: 0mV
Range: 0-224mV
Default: 0mV (000)
by REG_RST
by Watchdog
by REG_RST
by Watchdog
by REG_RST
by Watchdog
Thermal Regulation Threshold
00 – 60°C
01 – 80°C
10 – 100°C
11 – 120°C (default)
by REG_RST
by Watchdog
0
TREG[0]
R/W
42
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.4.10 REG09
图 37. REG09
7
0
6
1
5
0
4
0
3
0
2
1
1
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 18. REG09
Bit
Field
Type
Reset
Description
Force Start Input Current Optimizer (ICO)
0 – Do not force ICO (default)
1 – Force ICO
by REG_RST
by Watchdog
7
FORCE_ICO
R/W
Note:
This bit is can only be set only and always returns to 0 after ICO starts
Safety Timer Setting during DPM or Thermal Regulation
0 – Safety timer not slowed by 2X during input DPM or thermal
regulation
1 – Safety timer slowed by 2X during input DPM or thermal regulation
(default)
by REG_RST
by Watchdog
6
TMR2X_EN
R/W
Force BATFET off to enable ship mode with tSM_DLY delay time
0 – Allow BATFET turn on (default)
1 – Force BATFET off
5
4
BATFET_DIS
R/W
R/W
by REG_RST
JEITA High Temperature Voltage Setting
0 – Set Charge Voltage to VREG-200mV during JEITA hig temperature
(default)
by REG_RST
by Watchdog
JEITA_VSET (45C-60C)
1 – Set Charge Voltage to VREG during JEITA high temperature
BATFET turn off delay control
3
2
BATFET_DLY
R/W
R/W
by REG_RST
by REG_RST
0 – BATFET turn off immediately when BATFET_DIS bit is set (default)
1 – BATFET turn off delay by tSM_DLY when BATFET_DIS bit is set
BATFET full system reset enable
0 – Disable BATFET full system reset
1 – Enable BATFET full system reset (default)
BATFET_RST_EN
Current pulse control voltage up enable
0 – Disable (default)
by REG_RST
by Watchdog
1 – Enable
Note:
1
0
PUMPX_UP
PUMPX_DN
R/W
R/W
This bit is can only be set when EN_PUMPX bit is set and returns to 0
after current pulse control sequence is completed
Current pulse control voltage down enable
0 – Disable (default)
1 – Enable
Note:
by REG_RST
by Watchdog
This bit is can only be set when EN_PUMPX bit is set and returns to 0
after current pulse control sequence is completed
版权 © 2016–2017, Texas Instruments Incorporated
43
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4.11 REG0A
图 38. REG0A
7
0
6
1
5
1
4
1
3
0
2
1
1
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 19. REG0A
Bit
Field
Type
Reset
Description
by REG_RST
by Watchdog
7
BOOSTV[3]
R/W
512mV
by REG_RST
by Watchdog
Boost Voltage Control
Offset: 4.55V
Range: 4.55V – 5.51V
Default:4.998V(0111)
6
5
4
3
BOOSTV[2]
BOOSTV[1]
BOOSTV[0]
PFM_OTG_DIS
R/W
R/W
R/W
R/W
256mV
128mV
64mV
by REG_RST
by Watchdog
by REG_RST
by Watchdog
0 – Enable (default = 0)
1 – Disable
by REG_RST
Boost Current Limit
by REG_RST
by Watchdog
000: 0.5A
001: 0.8A
010: 1.0A
011: 1.2A
100: 1.5A
101: 1.8A
110: 2.1A
111: 2.4A
2
1
BOOST_LIM[2]
R/W
R/W
by REG_RST
by Watchdog
Boost Mode Current Limit
Default: 1.5A (100)
BOOST_LIM[1]
BOOST_LIM[0]
by REG_RST
by Watchdog
0
R/W
44
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.4.12 REG0B
图 39. REG0B
7
x
6
x
5
x
4
x
3
x
2
x
1
x
0
x
R
R
R
R
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 20. REG0B
Bit
7
Field
Type
R
Reset
N/A
Description
VBUS_STAT[2]
VBUS_STAT[1]
VBUS Status register
bq25898D
000: No Input 001: USB Host SDP
010: USB CDP (1.5A)
6
R
N/A
011: USB DCP (3.25A)
100: Adjustable High Voltage DCP (MaxCharge) (1.5A)
101: Unknown Adapter (500mA)
110: Non-Standard Adapter (1A/2A/2.1A/2.4A)
111: OTG
bq25898
5
VBUS_STAT[0]
R
N/A
000: No Input
001: USB Host SDP
010: Adapter (3.25A)
111: OTG
Note: Software current limit is reported in IINLIM register
4
3
CHRG_STAT[1]
CHRG_STAT[0]
R
R
N/A
N/A
Charging Status
00 – Not Charging
01 – Pre-charge ( < VBATLOWV
10 – Fast Charging
)
11 – Charge Termination Done
Power Good Status
0 – Not Power Good
1 – Power Good
2
1
0
PG_STAT
Reserved
R
R
R
N/A
N/A
N/A
Reserved: Always reads 1
VSYS Regulation Status
0 – Not in VSYSMIN regulation (BAT > VSYSMIN)
1 – In VSYSMIN regulation (BAT < VSYSMIN)
VSYS_STAT
版权 © 2016–2017, Texas Instruments Incorporated
45
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4.13 REG0C
图 40. REG0C
7
x
6
x
5
x
4
x
3
x
2
x
1
x
0
x
R
R
R
R
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 21. REG0C
Bit
Field
Type
Reset
Description
Watchdog Fault Status
Status 0 – Normal
7
WATCHDOG_FAULT
R
N/A
1- Watchdog timer expiration
Boost Mode Fault Status
0 – Normal
1 – VBUS overloaded in OTG, or VBUS OVP, or battery is too low in
boost mode
6
5
BOOST_FAULT
CHRG_FAULT[1]
R
R
N/A
N/A
Charge Fault Status
00 – Normal
01 – Input fault (VBUS > VACOV or VBAT < VBUS < VVBUSMIN(typical 3.8V)
)
4
CHRG_FAULT[0]
R
N/A
10 - Thermal shutdown
11 – Charge Safety Timer Expiration
Battery Fault Status
0 – Normal
3
BAT_FAULT
R
N/A
1 – BATOVP (VBAT > VBATOVP
)
2
1
NTC_FAULT[2]
NTC_FAULT[1]
R
R
N/A
N/A
NTC Fault Status
Buck Mode:
000 – Normal
010 – TS Warm
011 – TS Cool
101 – TS Cold
110 – TS Hot
Boost Mode:
0
NTC_FAULT[0]
R
N/A
000 – Normal
101 – TS Cold
110 – TS Hot
46
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.4.14 REG0D
图 41. REG0D
7
0
6
0
5
0
4
1
3
0
2
0
1
1
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 22. REG0D
Bit
Field
Type
Reset
Description
VINDPM Threshold Setting Method
7
FORCE_VINDPM
R/W
by REG_RST
0 – Run Relative VINDPM Threshold (default)
1 – Run Absolute VINDPM Threshold
6
5
4
3
2
1
0
VINDPM[6]
VINDPM[5]
VINDPM[4]
VINDPM[3]
VINDPM[2]
VINDPM[1]
VINDPM[0]
R/W
R/W
R/W
R/W
R/W
R/W
R/W
by REG_RST
by REG_RST
by REG_RST
by REG_RST
by REG_RST
by REG_RST
by REG_RST
6400mV
3200mV
1600mV
800mV
400mV
200mV
100mV
Absolute VINDPM Threshold
Offset: 2.6V
Range: 3.9V (0001101) – 15.3V (1111111)
Default: 4.4V (0010010)
Note:
Value < 0001101 is clamped to 3.9V (0001101)
Register is read only when FORCE_VINDPM=0 and can
be written by internal control based on relative VINDPM
threshold setting
Register can be read/write when FORCE_VINDPM = 1
9.4.15 REG0E
图 42. REG0E
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
R
R
R
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 23. REG0E
Bit
Field
Type
Reset
Description
Thermal Regulation Status
0 – Normal
7
THERM_STAT
R
N/A
1 – In Thermal Regulation
6
5
4
3
2
1
0
BATV[6]
BATV[5]
BATV[4]
BATV[3]
BATV[2]
BATV[1]
BATV[0]
R
R
R
R
R
R
R
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1280mV
640mV
320mV
160mV
80mV
40mV
20mV
ADC conversion of Battery Voltage (VBAT
Offset: 2.304V
Range: 2.304V (0000000) – 4.848V (1111111)
Default: 2.304V (0000000)
)
版权 © 2016–2017, Texas Instruments Incorporated
47
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4.16 REG0F
图 43. REG0F
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
R
R
R
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 24. REG0F
Bit
7
Field
Type
R
Reset
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Description
Reserved
SYSV[6]
SYSV[5]
SYSV[4]
SYSV[3]
SYSV[2]
SYSV[1]
SYSV[0]
Reserved: Always reads 0
1280mV
6
R
5
R
640mV
4
R
320mV
160mV
80mV
40mV
20mV
ADC conversion of System Voltage (VSYS
Offset: 2.304V
Range: 2.304V (0000000) – 4.848V (1111111)
Default: 2.304V (0000000)
)
3
R
2
R
1
R
0
R
9.4.17 REG10
图 44. REG10
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
R
R
R
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 25. REG10
Bit
7
Field
Type
R
Reset
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Description
Reserved
TSPCT[6]
TSPCT[5]
TSPCT[4]
TSPCT[3]
TSPCT[2]
TSPCT[1]
TSPCT[0]
Reserved: Always reads 0
29.76%
6
R
5
R
14.88%
4
R
7.44%
3.72%
1.86%
0.93%
0.465%
ADC conversion of TS Voltage (TS) as percentage of REGN
Offset: 21%
Range 21% (0000000) – 80% (1111111)
Default: 21% (0000000)
3
R
2
R
1
R
0
R
48
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
9.4.18 REG11
图 45. REG11
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
R
R
R
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 26. REG11
Bit
Field
Type
Reset
Description
VBUS Good Status
0 – Not VBUS attached
1 – VBUS Attached
7
VBUS_GD
R
N/A
6
5
4
3
2
1
0
VBUSV[6]
VBUSV[5]
VBUSV[4]
VBUSV[3]
VBUSV[2]
VBUSV[1]
VBUSV[0]
R
R
R
R
R
R
R
N/A
N/A
N/A
N/A
N/A
N/A
N/A
6400mV
3200mV
1600mV
800mV
400mV
200mV
100mV
ADC conversion of VBUS voltage (VBUS
Offset: 2.6V
Range 2.6V (0000000) – 15.3V (1111111)
Default: 2.6V (0000000)
)
9.4.19 REG12
图 46. REG12
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
R
R
R
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 27. REG12
Bit
7
Field
Type
R
Reset
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Description
Always reads 0
3200mA
Unused
6
ICHGR[6]
ICHGR[5]
ICHGR[4]
ICHGR[3]
ICHGR[2]
ICHGR[1]
ICHGR[0]
R
5
R
1600mA
800mA
400mA
200mA
100mA
50mA
ADC conversion of Charge Current (IBAT) when VBAT
VBATSHORT
Offset: 0mA
Range 0mA (0000000) – 6350mA (1111111)
Default: 0mA (0000000)
>
4
R
3
R
2
R
Note:
This register returns 0000000 for VBAT < VBATSHORT
1
R
0
R
版权 © 2016–2017, Texas Instruments Incorporated
49
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
9.4.20 REG13
图 47. REG13
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
R
R
R
R
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 28. REG13
Bit
Field
Type
Reset
Description
VINDPM Status
0 – Not in VINDPM
1 – VINDPM
7
VDPM_STAT
R
N/A
IINDPM Status
0 – Not in IINDPM
1 – IINDPM
6
IDPM_STAT
R
N/A
5
4
3
2
1
0
IDPM_LIM[5]
IDPM_LIM[4]
IDPM_LIM[3]
IDPM_LIM[2]
IDPM_LIM[1]
IDPM_LIM[0]
R
R
R
R
R
R
N/A
N/A
N/A
N/A
N/A
N/A
1600mA
800mA
Input Current Limit in effect while Input Current Optimizer
(ICO) is enabled
Offset: 100mA (default)
400mA
200mA
100mA
50mA
Range 100mA (0000000) – 3.25mA (1111111)
9.4.21 REG14
图 48. REG14
7
0
6
0
5
X
R
4
X
R
3
X
R
2
1
1
0
0
1
R/W
R
R
R
R
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
表 29. REG14
Bit
Field
Type
Reset
Description
Register Reset
0 – Keep current register setting (default)
7
REG_RST
R/W
N/A
1 – Reset to default register value and reset safety timer
Note:
Reset to 0 after register reset is completed
Input Current Optimizer (ICO) Status
0 – Optimization is in progress
6
ICO_OPTIMIZED
R
N/A
1 – Maximum Input Current Detected
5
4
3
PN[2]
PN[1]
PN[0]
R
R
R
N/A
N/A
N/A
Device Configuration
010: bq25898D
000: bq25898
Temperature Profile
1- JEITA (default)
2
TS_PROFILE
R
N/A
1
0
DEV_REV[1]
DEV_REV[0]
R
R
N/A
N/A
Device Revision: 01
50
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
10 Application and Implementation
注
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
A typical application consists of the device configured as an I2C controlled power path management device and a
single cell battery charger for Li-Ion and Li-polymer batteries used in a wide range of smartphones and other
portable devices. It integrates an input reverse-block FET (RBFET, Q1), high-side switching FET (HSFET, Q2),
low-side switching FET (LSFET, Q3), and BATFET (Q4) between the system and battery. The device also
integrates a bootstrap diode for the high-side gate drive.
10.2 Typical Application Diagram
Input
3.9Vœ14V at 3A
OTG
5V at 2.4A
1uH
VBUS
PMID
SW
1uF
8.2uF
10uF
10uF
BTST
DSEL
D+
USB
REGN
D-
PGND
SYS
ILIM
SYS
Ichg=4A
BAT
BATSEN
VREF
10uF
/QON
STAT
Host
SDA
SCL
INT
REGN
OTG
/CE
TS
bq25898D
Copyright © 2016, Texas Instruments Incorporated
VREF is the pull up voltage of I2C communication interface
图 49. bq25898D Application Diagram with PSEL with Interface and USB On-The-Go (OTG)
10.2.1 Design Requirements
For this design example, use the parameters shown in 表 30.
表 30. Design Parameters
PARAMETER
Input voltage range
Input current limit
Fast charge current
Output voltage
VALUE
3.9 V to 14 V
1.5 A
4032 mA
4.208 V
版权 © 2016–2017, Texas Instruments Incorporated
51
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
10.2.2 Detailed Design Procedure
10.2.2.1 Inductor Selection
The device has 1.5 MHz switching frequency to allow the use of small inductor and capacitor values. The
Inductor saturation current should be higher than the charging current (ICHG) plus half the ripple current (IRIPPLE):
I
³ I
+ (1/2) I
BAT
CHG
RIPPLE
(5)
The inductor ripple current depends on input voltage (VBUS), duty cycle (D = VBAT/VVBUS), switching frequency (fs)
and inductance (L):
V
x D x (1-D)
BUS
I
=
RIPPLE
f s x L
(6)
The maximum inductor ripple current happens with D = 0.5 or close to 0.5. Usually inductor ripple is designed in
the range of (20–40%) maximum charging current as a trade-off between inductor size and efficiency for a
practical design.
10.2.2.2 Buck Input Capacitor
Input capacitor should have enough ripple current rating to absorb input switching ripple current. The worst case
RMS ripple current is half of the charging current when duty cycle is 0.5. If the converter does not operate at
50% duty cycle, then the worst case capacitor RMS current IPMID occurs where the duty cycle is closest to 50%
and can be estimated by 公式 7:
I
= I x D x (1 - D)
CHG
PMID
(7)
Low ESR ceramic capacitor such as X7R or X5R is preferred for input decoupling capacitor and should be
placed to the drain of the high side MOSFET and source of the low side MOSFET as close as possible. Voltage
rating of the capacitor must be higher than normal input voltage level. 25 V rating or higher capacitor is preferred
for up to 14-V input voltage. 8.2-μF capacitance is suggested for typical of 3 A – 5 A charging current.
10.2.2.3 System Output Capacitor
Output capacitor also should have enough ripple current rating to absorb output switching ripple current. The
output capacitor RMS current ICOUT is given:
I
RIPPLE
I
=
» 0.29 x I
RIPPLE
CSYS
2 x
3
(8)
The output capacitor voltage ripple can be calculated as follows:
æ
ö
÷
÷
÷
V
V
SYS
SYS
ç
DV
=
ç1-
O
ç
ç
è
2
÷
ø
V
BUS
8 LC
SYS
f s
(9)
At certain input/output voltage and switching frequency, the voltage ripple can be reduced by increasing the
output filter LC. The charger device has internal loop compensator. To get good loop stability, 1-µH and minimum
of 20-µF output capacitor is recommended. The preferred ceramic capacitor is 6V or higher rating, X7R or X5R.
52
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
10.2.3 Application Curves
VBAT = 3.2 V,
VBUS = 5 V
VBAT = 3.2 V,
VBUS = 5 V
图 50. Power Up with Charge Disabled
图 51. Power Up with Charge Enabled
VBUS = 5 V
VBUS = 5 V
图 52. Charge Enable
图 53. Charge Disable
VBUS = 5 V
IIN = 3 A
Charge Disable
VBUS = 9 V
ICHG = 2 A
IIN = 1.5 A
VBAT = 3.8 V
ISYS = 0 A - 4 A
图 54. Input Current DPM Response without Battery
图 55. Load Transient During Supplement Mode
版权 © 2016–2017, Texas Instruments Incorporated
53
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
VBUS = 12 V
VBAT = 3.8 V
ICHG = 3 A
VBUS = 9V
No Battery
ISYS = 20 mA,
Charge Disable
图 56. PWM Switching Waveform
图 57. PFM Switching Waveform
VBAT = 3.8 V
ILOAD = 1 A
VBAT = 3.8 V
ILOAD = 0 A - 1 A
图 58. Boost Mode Switching Waveform
图 59. Boost Mode Load Transient
VBAT = 3.2 V
VBUS = 12 V
VBUS = 12 V
图 60. Power Up with Charge Disabled
图 61. Charge Enable
54
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
VBUS = 12 V
VBUS = 12 V
VBAT = 3.8 V
ICHG = 3 A
图 62. Charge Disable
图 63. PWM Switching Waveform
VBUS = 12 V
ISYS = 7 mA
Charge Disable
图 64. PFM Switching Waveform
版权 © 2016–2017, Texas Instruments Incorporated
55
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
10.3 System Example
Input
3.9Vœ14V at 3A
OTG
5V at 2.4A
SYS 3.5V œ 4.5V
1ꢀH
VBUS
PMID
SW
1ꢀF
C1
47nF
USB
10ꢀF 10ꢀF
BTST
REGN
VOK
47nF
4.7ꢀF
PSEL
ILIM
PHY
260Q
PGND
SYS
BAT
Ichg=4A
10uF
SYS
SYS
BATSEN
VREF
2.2YQ
2.2YQ
/QON
STAT
/PG
10YQ 10YQ 10YQ
Host
Optional
REGN
SDA
SCL
INT
OTG
/CE
5.23YQ
TS
10YQ
30.1YQ
bq25898
Copyright © 2016, Texas Instruments Incorporated
C1 = 8.2µF (OTG ≤ 1.8A) or 20µF (OTG ≤ 2.4A) is recommended
图 65. bq25898 with PSEL Interface and USB On-The-Go (OTG)
56
版权 © 2016–2017, Texas Instruments Incorporated
bq25898, bq25898D
www.ti.com.cn
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
11 Power Supply Recommendations
In order to provide an output voltage on SYS, the device requires a power supply between 3.9 V and 14 V input
with at least 100-mA current rating connected to VBUS or a single-cell Li-Ion battery with voltage > VBATUVLO
connected to BAT. The source current rating needs to be at least 3 A in order for the buck converter of the
charger to provide maximum output power to SYS.
12 Layout
12.1 Layout Guidelines
The switching node rise and fall times should be minimized for minimum switching loss. Proper layout of the
components to minimize high frequency current path loop (see 图 66) is important to prevent electrical and
magnetic field radiation and high frequency resonant problems. Here is a PCB layout priority list for proper
layout. Layout PCB according to this specific order is essential.
1. Place input capacitor as close as possible to PMID pin and GND pin connections and use shortest copper
trace connection or GND plane.
2. Put output capacitor near to the inductor and the IC.
3. Decoupling capacitors should be placed next to the IC pins and make trace connection as short as possible.
4. Place inductor input terminal to SW pin as close as possible. Minimize the copper area of this trace to lower
electrical and magnetic field radiation but make the trace wide enough to carry the charging current. Do not
use multiple layers in parallel for this connection. Minimize parasitic capacitance from this area to any other
trace or plane.
5. Connect all grounds together to reduce PCB size and improve thermal dissipation.
6. Avoid ground planes in parallel with high frequency traces in other layers.
12.2 Layout Example
图 66. High Frequency Current Path
版权 © 2016–2017, Texas Instruments Incorporated
57
bq25898, bq25898D
ZHCSG50B –MARCH 2016–REVISED MARCH 2017
www.ti.com.cn
13 器件和文档支持
13.1 器件支持
13.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
13.2 相关链接
下面的表格列出了快速访问链接。类别包括技术文档、支持与社区资源、工具和软件,以及申请样片或购买产品的
快速链接。
表 31. 相关链接
器件
产品文件夹
请单击此处
请单击此处
立即订购
请单击此处
请单击此处
技术文档
请单击此处
请单击此处
工具和软件
请单击此处
请单击此处
支持和社区
请单击此处
请单击此处
bq25898
bq25898D
13.3 接收文档更新通知
要接收文档更新通知,请导航至 TI.com 上的器件产品文件夹。请单击右上角的通知我 进行注册,即可收到任意产
品信息更改每周摘要。有关更改的详细信息,请查看任意已修订文档中包含的修订历史记录。
13.4 社区资源
下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范,
并且不一定反映 TI 的观点;请参阅 TI 的 《使用条款》。
TI E2E™ 在线社区 TI 的工程师对工程师 (E2E) 社区。此社区的创建目的在于促进工程师之间的协作。在
e2e.ti.com 中,您可以咨询问题、分享知识、拓展思路并与同行工程师一道帮助解决问题。
设计支持
TI 参考设计支持 可帮助您快速查找有帮助的 E2E 论坛、设计支持工具以及技术支持的联系信息。
13.5 商标
MaxCharge, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
13.6 静电放电警告
这些装置包含有限的内置 ESD 保护。 存储或装卸时,应将导线一起截短或将装置放置于导电泡棉中,以防止 MOS 门极遭受静电损
伤。
13.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 机械、封装和可订购信息
以下页面包括机械、封装和可订购信息。这些信息是指定器件的最新可用数据。这些数据发生变化时,我们可能不
会另行通知或修订此文档。如欲获取此产品说明书的浏览器版本,请参见左侧的导航栏。
58
版权 © 2016–2017, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
BQ25898DYFFR
BQ25898DYFFT
BQ25898YFFR
BQ25898YFFT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
42
42
42
42
3000 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
BQ25898D
SNAGCU
SNAGCU
SNAGCU
BQ25898D
BQ25898
BQ25898
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
BQ25898DYFFR
BQ25898DYFFT
BQ25898YFFR
BQ25898YFFT
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
42
42
42
42
3000
250
180.0
180.0
180.0
180.0
8.4
8.4
8.4
8.4
2.66
2.66
2.66
2.66
2.95
2.95
2.95
2.95
0.81
0.81
0.81
0.81
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
Q1
Q1
Q1
Q1
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jun-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
BQ25898DYFFR
BQ25898DYFFT
BQ25898YFFR
BQ25898YFFT
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
42
42
42
42
3000
250
182.0
182.0
182.0
182.0
182.0
182.0
182.0
182.0
20.0
20.0
20.0
20.0
3000
250
Pack Materials-Page 2
PACKAGE OUTLINE
YFF0042
DSBGA - 0.625 mm max height
S
C
A
L
E
4
.
5
0
0
DIE SIZE BALL GRID ARRAY
B
E
A
BUMP A1
CORNER
D
C
0.625 MAX
SEATING PLANE
0.05 C
BALL TYP
0.30
0.12
2 TYP
SYMM
G
F
E
D
C
D: Max = 2.852 mm, Min =2.792 mm
E: Max = 2.558 mm, Min =2.498 mm
SYMM
2.4
TYP
0.3
0.2
42X
B
A
0.015
C A
B
0.4 TYP
1
2
3
4
5
6
0.4 TYP
4222067/A 05/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
YFF0042
DSBGA - 0.625 mm max height
DIE SIZE BALL GRID ARRAY
(0.4) TYP
3
42X ( 0.23)
(0.4) TYP
1
2
4
5
6
A
B
C
SYMM
D
E
F
G
SYMM
LAND PATTERN EXAMPLE
SCALE:25X
0.05 MAX
0.05 MIN
(
0.23)
(
0.23)
METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
NON-SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
NOT TO SCALE
4222067/A 05/2015
NOTES: (continued)
3. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
For more information, see Texas Instruments literature number SNVA009 (www.ti.com/lit/snva009).
www.ti.com
EXAMPLE STENCIL DESIGN
YFF0042
DSBGA - 0.625 mm max height
DIE SIZE BALL GRID ARRAY
(0.4) TYP
42X ( 0.25)
(R0.05) TYP
1
2
3
4
5
6
A
(0.4)
TYP
B
METAL
TYP
C
D
E
F
SYMM
G
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
SCALE:30X
4222067/A 05/2015
NOTES: (continued)
4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022,德州仪器 (TI) 公司
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明