COP888CG-XXX/N [TI]
8-BIT, MROM, 4MHz, MICROCONTROLLER, PDIP40, DIP-40;型号: | COP888CG-XXX/N |
厂家: | TEXAS INSTRUMENTS |
描述: | 8-BIT, MROM, 4MHz, MICROCONTROLLER, PDIP40, DIP-40 光电二极管 外围集成电路 |
文件: | 总55页 (文件大小:625K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
COP888XG/CS
COP888xG/CS Family 8-Bit CMOS ROM Based Microcontrollers with 4k to 24k
Memory, Comparators and USART
Literature Number: SNOS874
July 1999
COP888xG/CS Family
8-Bit CMOS ROM Based Microcontrollers with 4k to 24k
Memory, Comparators and USART
Programmable) versions are available (COP8SGx7 Family).
Erasable windowed versions are available for use with a
range of software and hardware development tools.
General Description
Note: COP8SG devices are form-fit-function compatible su-
persets of the COP888xG/CL/CS Family devices, and are
Family features include an 8-bit memory mapped architec-
replacements for these in new designs, and design up-
ture, 10 MHz CKI with 1µs instruction cycle, three multi-
grades with minimum effort.
function 16-bit timer/counters, full-duplex USART,
The COP888xG ROM based microcontrollers are highly inte-
™
MICROWIRE/PLUS serial I/O, two Analog comparators,
™
grated COP8 Feature core devices with larger memory (4k
two power saving HALT/IDLE modes, idle timer, MIWU, high
current outputs, software selectable I/O options, WATCH-
to 24k) and advanced features including two Analog com-
parators. These single-chip CMOS devices are suited for
more complex applications requiring a full featured controller
with a range of memory sizes, low EMI (except EG), com-
parators, and a full-duplex USART. Pin and software com-
patible (different VCC range) 8k toor 32k OTP (One Time
™
DOG timer and Clock Monitor, low EMI 2.5V to 5.5V opera-
tion, and 28/40/44 pin packages.
Devices included in this datasheet are:
Memory
(bytes)
RAM
(bytes)
192
I/O
Device
Packages
28 DIP/SOIC
Temperature
Comments
4.5V - 5.5V
Pins
COP684CS 4k ROM
COP884CS 4k ROM
COP984CS 4k ROM
COP688CS 4k ROM
COP888CS 4k ROM
COP988CS 4k ROM
COP884CG 4k ROM
COP888CG 4k ROM
COP684EG 4k ROM
COP884EG 4k ROM
COP984EG 4k ROM
COP688EG 8k ROM
COP888EG 8k ROM
24
-55 to +125˚C
-40 to +85˚C
-0 to +70˚C
192
24
28 DIP/SOIC
192
24
28 DIP/SOIC
2.5V - 4.0V, CSH=4.0V - 6.0V
4.5V - 5.5V
192
36/40
36/40
36/40
24
40 DIP, 44 PLCC
40 DIP, 44 PLCC
40 DIP, 44 PLCC
28 DIP/SOIC
-55 to +125˚C
-40 to +85˚C
-0 to +70˚C
192
192
2.5V - 4.0V, CSH=4.0V - 6.0V
2.5V - 6.0V
128
-40 to +85˚C
-40 to +85˚C
-55 to +125˚C
-40 to +85˚C
0 to +70˚C
128
34/38
24
40 DIP, 44 PLCC
28 DIP, SOIC
2.5V - 6.0V
256
4.5V - 5.5V
256
24
28 DIP, SOIC
256
24
28 DIP, SOIC
2.5V - 4.0V, EGH=4.0 - 6.0V
4.5V - 5.5V
256
36/40
36/40
40 DIP, 44 PLCC
-55 to +125˚C
-40 to +85˚C
256
40 DIP, 44
PLCC/PQFP
COP988EG 8k ROM
COP688GG 16k ROM
256
512
36/40
36/40
40 DIP, 44 PLCC
0 to +70˚C
2.5V - 4.0V, EGH=4.0 - 6.0V
4.5V - 5.5V
40 DIP, 44
-55 to +125˚C
PLCC/PQFP
COP888GG 16k ROM
512
36/40
40 DIP, 44
-40 to +85˚C
PLCC/PQFP
COP688HG 20k ROM
COP888HG 20k ROM
COP688KG 24k ROM
COP888KG 24k ROM
512
512
512
512
36/40
36/40
36/40
36/40
40 DIP, 44 PLCC
40 DIP, 44 PLCC
40 DIP, 44 PLCC
40 DIP, 44 PLCC
-55 to +125˚C
-40 to +85˚C
-55 to +125˚C
-40 to +85˚C
4.5V - 5.5V
4.5V - 5.5V
— External Event counter mode
— Input Capture mode
n Quiet design (low radiated emissions)
n 4 to 24 kbytes on-board ROM
n 128 to 512 bytes on-board RAM
Key Features
n Full duplex USART
n Three 16-bit timers, each with two 16-bit registers
supporting:
— Processor Independent PWM mode
™
™
™
COP8 , MICROWIRE/PLUS , and WATCHDOG are trademarks of National Semiconductor Corporation.
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
iceMASTER® is a registered trademark of MetaLink Corporation.
© 2000 National Semiconductor Corporation
DS012829
www.national.com
n Up to fourteen multi-source vectored interrupts servicing
— External Interrupt with selectable edge
— Idle Timer T0
— Three Timers (one timer for the CS series)(each with
2 interrupts)
— MICROWIRE/PLUS
— Multi-Input Wake-Up
— Software Trap
— USART (2)
Key Features (Continued)
Additional Peripheral Features
n Idle Timer
n Multi-Input Wake-Up (MIWU) with optional interrupts (8)
n Two analog comparators (one for the CS series)
n WATCHDOG and Clock Monitor logic
n MICROWIRE/PLUS serial I/O
— Default VIS (default interrupt)
n 8-bit Stack Pointer SP—(stack in RAM)
n Two 8-bit Register Indirect Data Memory Pointers
(B and X)
I/O Features
n Memory mapped I/O
n Software selectable I/O options (TRI-STATE® Output,
Push-Pull Output, Weak Pull-Up Input, High Impedance
Input)
n Up to 8 high current outputs
n Schmitt trigger inputs on ports G and L
n Packages:
Fully Static CMOS
n Two power saving modes: HALT and IDLE
<
n Low current drain (typically 1 µA)
n Single supply operation: 2.5V–5.5V (COP88x)
— 44 PQFP with 40 I/O pins
— 44 PLCC with 40 I/O pins
— 40 DIP with 36 I/O pins
n Temperature ranges:
0˚C to +70˚C, −40˚C to +85˚C, and −55˚C to +125˚C
— 28 DIP/SOIC with 24 I/O pins
Development Support
n Emulation and OTP devices
CPU/Instruction Set Features
n 1 µs instruction cycle time
n Real time emulation and full program debug offered by
MetaLink’s Development System
n Versatile and easy to use instruction set
Block Diagram
DS012829-1
FIGURE 1. COP888xG Block Diagram
www.national.com
2
Connection Diagrams
Dual-In-Line Package
DS012829-46
Top View
Order Number COP884CS-XXX/WM,
COP984CS-XXX/WM,
COP984CSH-XXX/WM, COP684CS-XXX/WM,
COP884CG-XXX/WM,
DS012829-3
COP884EG-XXX/WM or
Top View
COP884CS-XXX/N, COP984CS-XXX/N,
COP984CSH-XXX/N, COP884CG-XXX/N,
COP884EG-XXX/N
Order Number COP888CS-XXX/N, COP988CS-XXX/N,
COP688CS-XXX/N,
COP988CSH-XXX/N, COP888CG-XXX/N,
COP688EG-XXX/N, COP888GG-XXX/N,
COP688GG-XXX/N, COP888GG-XXX/N,
COP688HG-XXX/N, COP888HG-XXX/N,
COP688KG-XXX/N, or COP888KG-XXX/N
See NS Package Number N40A
See NS Package Number M28B or N28A
Plastic Chip Carrier
DS012829-2
Top View
Order Number COP688CS-XXX/V, COP888CS-XXX/V,
COP988CS/CSH-XXX/V, COP688EG-XXX/V,
COP888EG-XXX/V, COP988EG-XXX/V,
COP888CG-XXX/V,
DS012829-45
COP688GG-XXX/V, COP888GG-XXX/V,
COP688HG-XXX/V, COP888HG-XXX/V,
COP688KG-XXX/V, or COP888KG-XXX/V
See NS Package Number V44A
Top View
Order Number COP888EG-XXX/VEJ,
COP688GG-XXX/VEJ, COP888GG-XXX/VEJ,
See NS Package Number VEJ44A
FIGURE 2. Connection Diagrams
3
www.national.com
Connection Diagrams (Continued)
Pinouts for 28-, 40- and 44-Pin Packages
28-Pin
DIP/SO
11
12
13
14
15
16
17
18
25
26
27
28
1
40-Pin
DIP
17
18
19
20
21
22
23
24
35
36
37
38
3
44-Pin
PLCC
17
18
19
20
25
26
27
28
39
40
41
42
3
44-Pin
PQFP
11
12
13
14
19
20
21
22
33
34
35
36
41
42
43
44
23
24
25
26
7
Port
L0
Type
I/O
Alt. Fun
MIWU
Alt. Fun
L1
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
WDOUT
I/O
I/O
I/O
I/O
I
MIWU
MIWU
MIWU
MIWU
MIWU
MIWU
MIWU
INT
CKX
TDX
RDX
T2A*
T2B*
T3A*
T3B*
L2
L3
L4
L5
L6
L7
G0
G1
G2
G3
G4
G5
G6
G7
D0
D1
D2
D3
D4
D5
D6
D7
I0
T1B
T1A
SO
SK
2
4
4
SI
3
5
5
I/CKO
O
HALT Restart
4
6
6
19
20
21
22
25
26
27
28
29
30
31
32
9
29
30
31
32
33
34
35
36
9
O
O
O
O
O
8
O
9
O
10
27
28
29
30
3
I
7
8
I1
I
COMP1IN−
COMP1IN+
COMP1OUT
COMP2IN−*
COMP2IN+*
COMP2OUT*
10
11
12
13
14
15
16
39
40
1
10
11
12
13
14
15
16
43
44
1
I2
I
9
I3
I
10
I4
I
I5
I
4
I6
I
5
I7
I
6
C0
C1
C2
C3
C4
C5
C6
C7
VCC
GND
CKI
RESET
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
37
38
39
40
15
16
17
18
2
2
2
21
22
23
24
8
6
23
5
8
33
7
37
7
31
1
24
34
38
32
*
Note 1: Not available on the CS series
www.national.com
4
Absolute Maximum Ratings (Note 4)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Total Current into VCC Pin (Source)
Total Current out of GND Pin (Sink)
Storage Temperature Range
Note 2: Absolute maximum ratings indicate limits beyond which damage to
the device may occur. DC and AC electrical specifications are not ensured
when operating the device at absolute maximum ratings.
100 mA
110 mA
−65˚C to +140˚C
Supply Voltage (VCC
Voltage at Any Pin
)
7V
−0.3V to VCC + 0.3V
DC Electrical Characteristics 98xEG and 98xCS:
0˚C ≤ TA ≤ +70˚C unless otherwise specified
Parameter
Operating Voltage
Conditions
Min
Typ
Max
Units
COP98xCS, COP98xEG
COP98xCSH, COP98xEGH
Power Supply Ripple (Note 6)
Supply Current (Note 7)
CKI = 10 MHz
2.5
4.0
4.0
6.0
V
V
V
Peak-to-Peak
0.1 VCC
VCC = 6.0V, tc = 1 µs
VCC = 6.0V, tc = 2.5 µs
VCC = 4V, tc = 2.5 µs
VCC = 4V, tc = 10 µs
VCC = 6.0V, CKI = 0 MHz
VCC = 4V, CKI = 0 MHz
12.5
5.5
2.5
1.4
8
mA
mA
mA
mA
µA
CKI = 4 MHz
CKI = 4 MHz
CKI = 1 MHz
<
<
HALT Current (Note 8)
0.7
0.3
4
µA
IDLE Current
CKI = 10 MHz
CKI = 4 MHz
CKI = 1 MHz
Input Levels (VIH, VIL)
RESET
VCC = 6.0V, tc = 1 µs
VCC = 6.0V, tc = 2.5 µs
VCC = 4V, tc = 10 µs
3.5
2.5
0.7
mA
mA
mA
Logic High
0.8 VCC
V
V
Logic Low
0.2 VCC
CKI (External adn Crystal Osc.
Modes)
Logic High
0.7 VCC
0.7 VCC
V
V
Logic Low
0.2 VCC
All Other Inputs
Logic High
V
V
Logic Low
0.2 VCC
+1
Hi-Z Input Leakage
Input Pullup Current
G and L Port Input Hysteresis
Output Current Levels
D Outputs
VCC = 6.0V, VIN = 0V
VCC = 6.0V, VIN = 0V
(Note 10)
−1
µA
µA
V
−40
−250
0.35 VCC
Source
VCC = 4V, VOH = 3.3V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOL = 1V
−0.4
−0.2
10
mA
mA
mA
mA
Sink
VCC = 2.5V, VOL = 0.4V
2.0
All Others
Source (Weak Pull-Up Mode)
VCC = 4V, VOH = 2.7V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOH = 3.3V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOL = 0.4V
VCC = 2.5V, VOL = 0.4V
−10
−2.5
−0.4
−0.2
1.6
−100
−33
µA
µA
Source (Push-Pull Mode)
Sink (Push-Pull Mode)
mA
mA
mA
mA
0.7
5
www.national.com
DC Electrical Characteristics 98xEG and 98xCS: (Continued)
0˚C ≤ TA ≤ +70˚C unless otherwise specified
Parameter
TRI-STATE Leakage
Allowable Sink/Source
Current per Pin
Conditions
Min
Typ
Max
Units
VCC = 6.0V
−1
+1
µA
D Outputs (Sink)
15
3
mA
mA
All others
Maximum Input Current
without Latchup (Notes 9, 10)
RAM Retention Voltage, Vr
Input Capacitance
±
TA = 25˚
500 ns Rise and Fall Time (min)
100
mA
V
2
7
pF
pF
Load Capacitance on D2
1000
AC Electrical Characteristics 98xEG and 98xCS:
0˚C ≤ TA ≤ +70˚C unless otherwise specified
Parameter
Instruction Cycle Time (tc)
Conditions
Min
Typ
Max
Units
Crystal, Resonator
4V ≤ VCC ≤ 6.0V
2.5
1.0
7.5
3.0
DC
DC
DC
DC
µs
µs
µs
µs
<
2.5V ≤ VCC 4V
R/C Oscillator
4V ≤ VCC ≤ 6.0V
<
2.5V ≤ VCC 4V
Inputs
tSETUP
4V ≤ VCC ≤ 6.0V
200
500
60
ns
ns
ns
ns
<
2.5V ≤ VCC 4V
tHOLD
4V ≤ VCC ≤ 6.0V
<
2.5V ≤ VCC 4V
150
Output Propagation Delay
RL = 2.2k, CL = 100 pF
tPD1, tPD0
SO, SK
4V ≤ VCC ≤ 6.0V
0.7
1.75
1
µs
µs
µs
µs
ns
ns
ns
<
2.5V ≤ VCC 4V
All Others
4V ≤ VCC ≤ 6.0V
<
2.5V ≤ VCC 4V
2.5
MICROWIRE Setup Time (tUWS) (Note 10)
MICROWIRE Hold Time (tUWH) (Note 10)
MICROWIRE Output Propagation Delay (tUPD
Input Pulse Width (Note 11)
20
56
)
220
Interrupt Input High Time
1
1
1
1
1
tc
tc
Interrupt Input Low Time
Timer 1, 2, 3 Input High Time
Timer 1, 2, 3 Input Low Time
Reset Pulse Width
tc
tc
µs
www.national.com
6
Absolute Maximum Ratings (Note 4)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Total Current into VCC Pin (Source)
Total Current out of GND Pin (Sink)
Storage Temperature Range
Note 3: Absolute maximum ratings indicate limits beyond which damage to
the device may occur. DC and AC electrical specifications are not ensured
when operating the device at absolute maximum ratings.
100 mA
110 mA
−65˚C to +140˚C
Supply Voltage (VCC
Voltage at Any Pin
)
7V
−0.3V to VCC + 0.3V
DC Electrical Characteristics 88xCG, 88xCS, and 88xEG:
−40˚C ≤ TA ≤ +85˚C unless otherwise specified
Parameter
Operating Voltage
Conditions
Min
Typ
Max
Units
Power Supply Ripple (Note 6)
Supply Current (Note 7)
CKI = 10 MHz
Peak-to-Peak
0.1 VCC
V
VCC = 6.0V, tc = 1 µs
VCC = 6.0V, tc = 2.5 µs
VCC = 4V, tc = 2.5 µs
12.5
5.5
mA
mA
mA
CKI = 4 MHz
CKI = 4 MHz
2.5
(88xCG & 88xEG only)
CKI = 1 MHz
VCC = 4V, tc = 10 µs
1.4
mA
(88xCG & 88xEG only)
<
<
HALT Current (Note 8)
(88xCG & 88xEG only)
IDLE Current
VCC = 6.0V, CKI = 0 MHz
VCC = 4V, CKI = 0 MHz
1.0
0.5
8
4
µA
µA
CKI = 10 MHz
VCC = 6.0V, tc = 1 µs
VCC = 6.0V, tc = 2.5 µs
VCC = 4V, tc = 10 µs
3.5
2.5
0.7
mA
mA
mA
CKI = 4 MHz
CKI = 1 MHz
(88xCG & 88xEG only)
Input Levels (VIH, VIL)
RESET
Logic High
0.8 VCC
V
V
Logic Low
0.2 VCC
CKI (External adn Crystal Osc.
Modes)
Logic High
0.7 VCC
0.7 VCC
V
V
Logic Low
0.2 VCC
All Other Inputs
Logic High
V
V
Logic Low
0.2 VCC
+2
Hi-Z Input Leakage
Input Pullup Current
G and L Port Input Hysteresis
Output Current Levels
D Outputs
VCC = 6.0V
−2
µA
µA
V
VCC = 6.0V, VIN = 0V
(Note 10)
−40
−250
0.35 VCC
Source
VCC = 4V, VOH = 3.3V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOL = 1V
−0.4
−0.2
10
mA
mA
mA
mA
Sink
VCC = 2.5V, VOL = 0.4V
2.0
All Others
Source (Weak Pull-Up Mode)
VCC = 4V, VOH = 2.7V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOH = 3.3V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOL = 0.4V
−10
−2.5
−0.4
−0.2
1.6
−100
−33
µA
µA
Source (Push-Pull Mode)
Sink (Push-Pull Mode)
mA
mA
mA
7
www.national.com
DC Electrical Characteristics 88xCG, 88xCS, and 88xEG: (Continued)
−40˚C ≤ TA ≤ +85˚C unless otherwise specified
Parameter
Conditions
VCC = 2.5V, VOL = 0.4V
VCC = 6.0V
Min
0.7
−1
Typ
Max
Units
mA
TRI-STATE Leakage
Allowable Sink/Source
Current per Pin
+1
µA
D Outputs (Sink)
15
3
mA
mA
All others
Maximum Input Current
without Latchup (Notes 9, 10)
RAM Retention Voltage, Vr
Input Capacitance
±
TA = 25˚
100
mA
V
500 ns Rise and Fall Time (min)
2
7
pF
pF
Load Capacitance on D2
1000
AC Electrical Characteristics 888EG, 88xCS, and 88xCG:
−40˚C ≤ TA ≤ +85˚C unless otherwise specified
Parameter
Instruction Cycle Time (tc)
Conditions
Min
Typ
Max
Units
Crystal, Resonator
4V ≤ VCC ≤ 6.0V
1.0
2.5
3.0
7.5
DC
DC
DC
DC
µs
µs
µs
µs
<
2.5V ≤ VCC 4V
R/C Oscillator
4V ≤ VCC ≤ 6.0V
<
2.5V ≤ VCC 4V
Inputs
tSETUP
4V ≤ VCC ≤ 6.0V
200
500
60
ns
ns
ns
ns
<
2.5V ≤ VCC 4V
tHOLD
4V ≤ VCC ≤ 6.0V
<
2.5V ≤ VCC 4V
150
Output Propagation Delay
RL = 2.2k, CL = 100 pF
tPD1, tPD0
SO, SK
4V ≤ VCC ≤ 6.0V
0.7
1.75
1
µs
µs
µs
µs
ns
ns
ns
<
2.5V ≤ VCC 4V
All Others
4V ≤ VCC ≤ 6.0V
<
2.5V ≤ VCC 4V
2.5
MICROWIRE Setup Time (tUWS) (Note 10)
MICROWIRE Hold Time (tUWH) (Note 10)
MICROWIRE Output Propagation Delay (tUPD
Input Pulse Width (Note 11)
20
56
)
220
Interrupt Input High Time
1
1
1
1
1
tc
tc
Interrupt Input Low Time
Timer 1, 2, 3 Input High Time
Timer 1, 2, 3 Input Low Time
Reset Pulse Width
tc
tc
µs
www.national.com
8
Absolute Maximum Ratings (Note 4)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Total Current into VCC Pin (Source)
Total Current out of GND Pin (Sink)
Storage Temperature Range
Note 4: Absolute maximum ratings indicate limits beyond which damage to
the device may occur. DC and AC electrical specifications are not ensured
when operating the device at absolute maximum ratings.
100 mA
110 mA
−65˚C to +140˚C
Supply Voltage (VCC
Voltage at Any Pin
)
7V
−0.3V to VCC + 0.3V
DC Electrical Characteristics 888GG, 888HG, and 888KG:
−40˚C ≤ TA ≤ +85˚C unless otherwise specified
Parameter
Operating Voltage
Conditions
Min
Typ
Max
5.5
Units
2.5
V
V
Power Supply Ripple (Note 6)
Supply Current (Note 7)
CKI = 10 MHz
Peak-to-Peak
0.1 VCC
VCC = 5.5V, tc = 1 µs
VCC = 5.5V, tc = 2.5 µs
VCC = 4V, tc = 2.5 µs
VCC = 4V, tc = 10 µs
VCC = 5.5V, CKI = 0 MHz
VCC = 4V, CKI = 0 MHz
12.5
5.5
2.5
1.4
10
mA
mA
mA
mA
µA
CKI = 4 MHz
CKI = 4 MHz
CKI = 1 MHz
<
HALT Current (Note 8)
1
<
0.5
6
µA
IDLE Current
CKI = 10 MHz
CKI = 4 MHz
VCC = 5.5V, tc = 1 µs
VCC = 5.5V, tc = 2.5 µs
VCC = 4V, tc = 10 µs
3.5
2.5
0.7
mA
mA
mA
CKI = 1 MHz
Input Levels (VIH, VIL)
RESET
Logic High
0.8 VCC
0.7 VCC
V
V
Logic Low
0.2 VCC
CKI, All Other Inputs
Logic High
V
V
Logic Low
0.2 VCC
+2
Hi-Z Input Leakage
Input Pullup Current
G and L Port Input Hysteresis
Output Current Levels
D Outputs
VCC = 5.5V, VIN = 0V
VCC = 5.5V, VIN = 0V
(Note 10)
−2
µA
µA
V
−40
−250
0.35 VCC
Source
VCC = 4V, VOH = 3.3V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOL = 1V
−0.4
−0.2
10
mA
mA
mA
mA
Sink
VCC = 2.5V, VOL = 0.4V
2.0
All Others
Source (Weak Pull-Up Mode)
VCC = 4V, VOH = 2.7V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOH = 3.3V
VCC = 2.5V, VOH = 1.8V
VCC = 4V, VOL = 0.4V
VCC = 2.5V, VOL = 0.4V
VCC = 5.5V
−10
−2.5
−0.4
−0.2
1.6
−100
−33
µA
µA
Source (Push-Pull Mode)
Sink (Push-Pull Mode)
mA
mA
mA
mA
µA
0.7
TRI-STATE Leakage
Allowable Sink/Source
Current per Pin
−2
+2
D Outputs (Sink)
All others
15
3
mA
mA
Maximum Input Current
9
www.national.com
DC Electrical Characteristics 888GG, 888HG, and 888KG: (Continued)
−40˚C ≤ TA ≤ +85˚C unless otherwise specified
Parameter
without Latchup (Notes 9, 10)
RAM Retention Voltage, Vr
Input Capacitance
Conditions
Room Temperature
Min
Typ
Max
Units
mA
V
±
100
500 ns Rise and Fall Time (min)
2
7
pF
Load Capacitance on D2
(Note 10)
1000
pF
AC Electrical Characteristics 888GG, 888HG, and 888KG:
−40˚C ≤ TA ≤ +85˚C unless otherwise specified
Parameter
Conditions
Min
Typ
Max
Units
(88xCG & 88xEG only)
Instruction Cycle Time (tc)
<
Crystal, Resonator
R/C Oscillator
2.5V ≤ VCC 4V
1.0
2.5
3.0
7.5
DC
DC
DC
DC
µs
µs
µs
µs
4V ≤ VCC ≤ 5.5V
<
2.5V ≤ VCC 4V
4V ≤ VCC ≤ 5.5V
Inputs
tSETUP
4V ≤ VCC ≤ 5.5V
200
500
60
ns
ns
ns
ns
<
2.5V ≤ VCC 4V
tHOLD
4V ≤ VCC ≤ 5.5V
<
2.5V ≤ VCC 4V
150
Output Propagation Delay
RL = 2.2k, CL = 100 pF
tPD1, tPD0
SO, SK
4V ≤ VCC ≤ 5.5V
0.7
1.75
1
µs
µs
µs
µs
ns
ns
ns
<
2.5V ≤ VCC 4V
All Others
4V ≤ VCC ≤ 5.5V
<
2.5V ≤ VCC 4V
2.5
MICROWIRE Setup Time (tUWS) (Note 10)
MICROWIRE Hold Time (tUWH) (Note 10)
MICROWIRE Output Propagation Delay (tUPD
Input Pulse Width (Note 11)
VCC ≥ 4V
VCC ≥ 4V
VCC ≥ 4V
20
56
)
220
Interrupt Input High Time
1
1
1
1
1
tc
tc
Interrupt Input Low Time
Timer 1, 2, 3 Input High Time
Timer 1, 2, 3 Input Low Time
Reset Pulse Width
tc
tc
µs
www.national.com
10
Absolute Maximum Ratings (Note 5)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Total Current into VCC Pin (Source)
Total Current out of GND Pin (Sink)
Storage Temperature Range
Note 5: Absolute maximum ratings indicate limits beyond which damage to
the device may occur. DC and AC electrical specifications are not ensured
when operating the device at absolute maximum ratings.
100 mA
110 mA
−65˚C to +140˚C
Supply Voltage (VCC
Voltage at Any Pin
)
7V
−0.3V to VCC + 0.3V
DC Electrical Characteristics 68xCS and 68xxG:
−55˚C ≤ TA ≤ +125˚C unless otherwise specified
Parameter
Operating Voltage
Conditions
Min
Typ
Max
5.5
Units
4.5
V
V
Power Supply Ripple (Note 6)
Supply Current (Note 7)
CKI = 10 MHz
Peak-to-Peak
0.1 VCC
VCC = 5.5V, tc = 1 µs
VCC = 5.5V, tc = 2.5 µs
VCC = 5.5V, CKI = 0 MHz
12.5
5.5
30
mA
mA
µA
CKI = 4 MHz
<
HALT Current (Note 8)
IDLE Current
10
CKI = 10 MHz
VCC = 5.5V, tc = 1 µs
VCC = 5.5V, tc = 2.5 µs
3.5
2.5
mA
mA
CKI = 4 MHz
Input Levels (VIH, VIL)
RESET
Logic High
0.8 VCC
0.7 VCC
0.7 VCC
V
V
Logic Low
0.2 VCC
0.2 VCC
CKI (68xCS & 68xEG only)
Logic High
V
V
Logic Low
All Other Inputs
Logic High
V
V
Logic Low
0.2 VCC
+5
Hi-Z Input Leakage
Input Pullup Current
G and L Port Input Hysteresis
Output Current Levels
D Outputs
VCC = 5.5V, VIN = 0V
VCC = 5.5V, VIN = 0V
(Note 10)
−5
µA
µA
V
−35
−400
0.35 VCC
Source
VCC = 4.5V, VOH = 3.3V
VCC = 4.5V, VOL = 1V
−0.4
9
mA
mA
Sink
All Others
Source (Weak Pull-Up Mode)
Source (Push-Pull Mode)
Sink (Push-Pull Mode)
TRI-STATE Leakage
Allowable Sink/Source
Current per Pin
VCC = 4.5V, VOH = 2.7V
VCC = 4.5V, VOH = 3.3V
VCC = 4.5V, VOL = 0.4V
VCC = 5.5V
−9
−0.4
1.4
−5
−140
+5
µA
mA
mA
µA
D Outputs (Sink)
All others
12
mA
mA
2.5
Maximum Input Current
without Latchup (Notes 9, 10)
RAM Retention Voltage, Vr
Input Capacitance
Load Capacitance on D2
±
Room Temp
100
7
mA
V
500 ns Rise and Fall Time (min)
(Note 10)
2
pF
pF
(Note 10)
1000
11
www.national.com
AC Electrical Characteristics 68xCS and 68xxG:
−55˚C ≤ TA ≤ +125˚C unless otherwise specified
Parameter
Instruction Cycle Time (tc)
Conditions
Min
Typ
Max
Units
Crystal, Resonator
VCC ≥ 4.5V
1.0
3.0
DC
DC
µs
µs
R/C Oscillator
VCC ≥ 4.5V
68xCS & 68xEG only)
Inputs
tSETUP
VCC ≥ 4.5V
200
60
ns
ns
tHOLD
VCC ≥ 4.5V
Output Propagation Delay
RL = 2.2k, CL = 100 pF
tPD1, tPD0
SO, SK
VCC ≥ 4.5V
VCC ≥ 4.5V
0.7
1
µs
µs
ns
ns
ns
All Others
™
MICROWIRE Setup Time (tUWS) (Note 10)
MICROWIRE Hold Time (tUWH) (Note 10)
MICROWIRE Output Propagation Delay (tUPD
Input Pulse Width (Note 11)
20
56
)
220
Interrupt Input High Time
1
1
1
1
1
tc
tc
Interrupt Input Low Time
Timer 1, 2, 3 Input High Time
Timer 1, 2, 3 Input Low Time
Reset Pulse Width
tc
tc
µs
Note 6: Maximum rate of voltage change must be less than 0.5 V/ms.
Note 7: Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 8: The HALT mode will stop CKI from oscillating in the RC and the Crystal configurations. Measurement of IDD HALT is done with device neither sourcing or
sinking current; with L, C, and G0–G5 programmed as low outputs and not driving a load; all outputs programmed low and not driving a load; all inputs tied to V
;
CC
clock monitor and comparators disabled. Parameter refers to HALT mode entered via setting bit 7 of the G Port data register. Part will pull up CKI during HALT in crys-
tal clock mode.
Note 9: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages greater than V
and the pins will have sink current
CC
to V when biased at voltages greater than V (the pins do not have source current when biased at a voltage below V ). The effective resistance to V is 750Ω
CC
CC
CC
CC
(typical). These two pins will not latch up. The voltage at the pins must be limited to less than 14V. WARNING: Voltages in excess of 14V will cause damage to the
pins. This warning excludes ESD transients.
Note 10: Parameter characterized but not tested.
Note 11: t = Instruction Cycle Time
c
Comparators AC and DC Characteristics
VCC = 5V, −40˚C ≤ TA ≤ +85˚C.
Parameter
Conditions
Min
Typ
Max
Units
mV
V
±
±
25
Input Offset Voltage
0.4V ≤ VIN ≤ VCC − 1.5V
10
Input Common Mode Voltage Range
Voltage Gain
0.4
VCC − 1.5
300k
V/V
mA
mA
µA
Low Level Output Current
High Level Output Current
DC Supply Current per Comparator (When Enabled)
Response Time
VOL = 0.4V
VOH = 4.6V
1.6
1.6
250
1
100 mV Overdrive,
100 pF Load
µs
www.national.com
12
Comparators AC and DC Characteristics (Continued)
DS012829-4
FIGURE 3. MICROWIRE/PLUS Timing
Typical Performance Characteristics (−55˚C ≤ TA = +125˚C)
DS012829-30
DS012829-31
DS012829-32
DS012829-33
13
www.national.com
Typical Performance Characteristics (−55˚C ≤ TA = +125˚C) (Continued)
DS012829-35
DS012829-34
DS012829-36
DS012829-38
DS012829-37
DS012829-39
www.national.com
14
Typical Performance Characteristics (−55˚C ≤ TA = +125˚C) (Continued)
DS012829-40
DS012829-41
L2 MIWU or TDX
Pin Descriptions
L1 MIWU or CKX
VCC and GND are the power supply pins. All VCC and GND
L0 MIWU
pins must be connected.
Port G is an 8-bit port with 5 I/O pins (G0, G2–G5), an input
pin (G6), and a dedicated output pin (G1). Pins G0 and
G2–G6 all have Schmitt Triggers on their inputs. Pin G1
serves as the dedicated WDOUT WATCHDOG output, while
pin G7 is either input or output depending on the oscillator
mask option selected. With the crystal oscillator option se-
lected, G7 serves as the dedicated output pin for the CKO
clock output. With the single-pin R/C oscillator mask option
selected, G7 serves as a general purpose input pin but is
also used to bring the device out of HALT mode with a low to
high transition on G7. There are two registers associated
with the G Port, a data register and a configuration register.
Therefore, each of the 5 I/O bits (G0, G2–G5) can be indi-
vidually configured under software control.
CKI is the clock input. This can come from an R/C generated
oscillator, or a crystal oscillator (in conjunction with CKO).
See Oscillator Description section.
RESET is the master reset input. See Reset Description sec-
tion.
The device contains three bidirectional 8-bit I/O ports (C, G
and L), where each individual bit may be independently con-
figured as an input (Schmitt Trigger inputs on ports L and G),
output or TRI-STATE under program control. Three data
memory address locations are allocated for each of these
I/O ports. Each I/O port has two associated 8-bit memory
mapped registers, the CONFIGURATION register and the
output DATA register. A memory mapped address is also re-
served for the input pins of each I/O port. (See the memory
map for the various addresses associated with the I/O ports.)
Figure 4 shows the I/O port configurations. The DATA and
CONFIGURATION registers allow for each port bit to be in-
dividually configured under software control as shown below:
Since G6 is an input only pin and G7 is the dedicated CKO
clock output pin (crystal clock option) or general purpose in-
put (R/C clock option), the associated bits in the data and
configuration registers for G6 and G7 are used for special
purpose functions as outlined on the next page. Reading the
G6 and G7 data bits will return zeros.
CONFIGURATION
DATA
Register
0
Port Set-Up
Register
0
Hi-Z Input
(TRI-STATE Output)
Input with Weak Pull-Up
Push-Pull Zero Output
Push-Pull One Output
0
1
1
1
0
1
PORT L is an 8-bit I/O port. All L-pins have Schmitt triggers
on the inputs.
The Port L supports Multi-Input Wake Up on all eight pins. L1
is used for the USART external clock. L2 and L3 are used for
the USART transmit and receive. L4 and L5 are used for the
timer input functions T2A and T2B. L6 and L7 are used for
the timer input functions T3A and T3B (execpt on the CS se-
ries).
DS012829-5
FIGURE 4. I/O Port Configurations
The Port L has the following alternate features:
L7 MIWU or T3B
Note that the chip will be placed in the HALT mode by writing
a “1” to bit 7 of the Port G Data Register. Similarly the chip
will be placed in the IDLE mode by writing a “1” to bit 6 of the
Port G Data Register.
L6 MIWU or T3A
L5 MIWU or T2B
L4 MIWU or T2A
Writing a “1” to bit 6 of the Port G Configuration Register en-
ables the MICROWIRE/PLUS to operate with the alternate
L3 MIWU or RDX
15
www.national.com
SP is the 8-bit stack pointer, which points to the subroutine/
interrupt stack (in RAM). The SP is initialized to RAM ad-
dress 06F with reset.
Pin Descriptions (Continued)
phase of the SK clock. The G7 configuration bit, if set high,
enables the clock start up delay after HALT when the R/C
clock configuration is used.
S is the 8-bit Data Segment Address Register used to extend
the lower half of the address range (00 to 7F) into 256 data
segments of 128 bytes each.
Config Reg.
CLKDLY
Alternate SK
Data Reg.
HALT
IDLE
All the CPU registers are memory mapped with the excep-
tion of the Accumulator (A) and the Program Counter (PC).
G7
G6
PROGRAM MEMORY
Port G has the following alternate features:
G6 SI (MICROWIRE Serial Data Input)
G5 SK (MICROWIRE Serial Clock)
G4 SO (MICROWIRE Serial Data Output)
G3 T1A (Timer T1 I/O)
The program memory consists of up to 24 kbytes of ROM.
These bytes may hold program instructions or constant data
(data tables for the LAID instruction, jump vectors for the JID
instruction, and interrupt vectors for the VIS instruction). The
program memory is addressed by the 15-bit program
counter (PC). All interrupts in the devices vector to program
memory location 0FF Hex.
G2 T1B (Timer T1 Capture Input)
G0 INTR (External Interrupt Input)
Port G has the following dedicated functions:
DATA MEMORY
G7 CKO Oscillator dedicated output or general purpose
input
The data memory address space includes the on-chip RAM
and data registers, the I/O registers (Configuration, Data and
Pin), the control registers, the MICROWIRE/PLUS SIO shift
register, and the various registers, and counters associated
with the timers (with the exception of the IDLE timer). Data
memory is addressed directly by the instruction or indirectly
by the B, X, SP pointers and S register.
G1 WDOUT WATCHDOG and/or Clock Monitor dedi-
cated output
Port C is an 8-bit I/O port. The 40-pin device does not have
a full complement of Port C pins. The unavailable pins are
not terminated. A read operation for these unterminated pins
will return unpredicatable values.
The data memory consists of up to 512 bytes of RAM. Six-
teen bytes of RAM are mapped as “registers” at addresses
0F0 to 0FF Hex. These registers can be loaded immediately,
and also decremented and tested with the DRSZ (decrement
register and skip if zero) instruction. The memory pointer
registers X, SP, B and S are memory mapped into this space
at address locations 0FC to 0FF Hex respectively, with the
other registers being available for general usage.
Port I is an eight-bit Hi-Z input port.
Port I1–I3 are used for Comparator 1. Port I4–I6 are used for
Comparator 2.
The Port I has the following alternate features:
I6 COMP2OUT (Comparator 2 Output)
I5 COMP2+IN (Comparator 2 Positive Input)
I4 COMP2−IN (Comparator 2 Negative Input)
I3 COMP1OUT (Comparator 1 Output)
The instruction set permits any bit in memory to be set, reset
or tested. All I/O and registers (except A and PC) are
memory mapped; therefore, I/O bits and register bits can be
directly and individually set, reset and tested. The accumula-
tor (A) bits can also be directly and individually tested.
Note: RAM contents are undefined upon power-up.
I2 COMP1+IN (Comparator 1 Positive Input)
I1 COMP1−IN (Comparator 1 Negative Input)
Port D is an 8-bit output port that is preset high when RESET
goes low. The user can tie two or more D port outputs (ex-
cept D2) together in order to get a higher drive.
Data Memory Segment RAM
Extension
Data memory address 0FF is used as a memory mapped lo-
cation for the Data Segment Address Register (S).
Functional Description
The architecture of the device is modified Harvard architec-
ture. With the Harvard architecture, the control store pro-
gram memory (ROM) is separated from the data store
memory (RAM). Both ROM and RAM have their own sepa-
rate addressing space with separate address buses. The ar-
chitecture, though based on Harvard architecture, permits
transfer of data from ROM to RAM.
The data store memory is either addressed directly by a
single byte address within the instruction, or indirectly rela-
tive to the reference of the B, X, or SP pointers (each con-
tains a single-byte address). This single-byte address allows
an addressing range of 256 locations from 00 to FF hex. The
upper bit of this single-byte address divides the data store
memory into two separate sections as outlined previously.
With the exception of the RAM register memory from ad-
dress locations 00F0 to 00FF, all RAM memory is memory
mapped with the upper bit of the single-byte address being
equal to zero. This allows the upper bit of the single-byte ad-
dress to determine whether or not the base address range
(from 0000 to 00FF) is extended. If this upper bit equals one
(representing address range 0080 to 00FF), then address
extension does not take place. Alternatively, if this upper bit
equals zero, then the data segment extension register S is
used to extend the base address range (from 0000 to 007F)
from XX00 to XX7F, where XX represents the 8 bits from the
S register. Thus the 128-byte data segment extensions are
located from addresses 0100 to 017F for data segment 1,
CPU REGISTERS
The CPU can do an 8-bit addition, subtraction, logical or shift
operation in one instruction (tc) cycle time.
There are six CPU registers:
A is the 8-bit Accumulator Register
PC is the 15-bit Program Counter Register
PU is the upper 7 bits of the program counter (PC)
PL is the lower 8 bits of the program counter (PC)
B is an 8-bit RAM address pointer, which can be optionally
post auto incremented or decremented.
X is an 8-bit alternate RAM address pointer, which can be
optionally post auto incremented or decremented.
www.national.com
16
Data Memory Segment RAM
Extension (Continued)
0200 to 027F for data segment 2, etc., up to FF00 to FF7F
for data segment 255. The base address range from 0000 to
007F represents data segment 0.
Figure 5 illustrates how the S register data memory exten-
sion is used in extending the lower half of the base address
range (00 to 7F hex) into 256 data segments of 128 bytes
each, with a total addressing range of 32 kbytes from XX00
to XX7F. This organization allows a total of 256 data seg-
ments of 128 bytes each with an additional upper base seg-
ment of 128 bytes. Furthermore, all addressing modes are
available for all data segments. The S register must be
changed under program control to move from one data seg-
ment (128 bytes) to another. However, the upper base seg-
ment (containing the 16 memory registers, I/O registers,
control registers, etc.) is always available regardless of the
contents of the S register, since the upper base segment
(address range 0080 to 00FF) is independent of data seg-
ment extension.
The instructions that utilize the stack pointer (SP) always ref-
erence the stack as part of the base segment (Segment 0),
regardless of the contents of the S register. The S register is
not changed by these instructions. Consequently, the stack
(used with subroutine linkage and interrupts) is always lo-
cated in the base segment. The stack pointer will be intitial-
ized to point at data memory location 006F as a result of re-
set.
DS012829-6
*
Reads as all ones.
FIGURE 5. RAM Organization
Reset
The 128 bytes of RAM contained in the base segment are
split between the lower and upper base segments. The first
112 bytes of RAM are resident from address 0000 to 006F in
the lower base segment, while the remaining 16 bytes of
RAM represent the 16 data memory registers located at ad-
dresses 00F0 to 00FF of the upper base segment. No RAM
is located at the upper sixteen addresses (0070 to 007F) of
the lower base segment.
The RESET input when pulled low initializes the microcon-
troller. Initialization will occur whenever the RESET input is
pulled low. Upon initialization, the data and configuration
registers for ports L, G and C are cleared, resulting in these
Ports being initialized to the TRI-STATE mode. Pin G1 of the
G Port is an exception (as noted below) since pin G1 is dedi-
cated as the WATCHDOG and/or Clock Monitor error output
pin. Port D is set high. The PC, PSW, ICNTRL, CNTRL,
T2CNTRL and T3CNTRL control registers are cleared. The
USART registers PSR, ENU (except that TBMT bit is set),
ENUR and ENUI are cleared. The Comparator Select Regis-
ter is cleared. The S register is initialized to zero. The
Multi-Input Wakeup registers WKEN and WKEDG are
cleared. Wakeup register WKPND is unknown. The stack
pointer, SP, is initialized to 6F hex.
Additional RAM beyond these initial 128 bytes, however, will
always be memory mapped in groups of 128 bytes (or less)
at the data segment address extensions (XX00 to XX7F) of
the lower base segment. The additional bytes of RAM are
memory mapped from segment 1 up through segment 3 (see
Figure 5).
The device comes out of reset with both the WATCHDOG
logic and the Clock Monitor detector armed, with the
WATCHDOG service window bits set and the Clock Monitor
bit set. The WATCHDOG and Clock Monitor circuits are in-
hibited during reset. The WATCHDOG service window bits
being initialized high default to the maximum WATCHDOG
service window of 64k tC clock cycles. The Clock Monitor bit
being initialized high will cause a Clock Monitor error follow-
ing reset if the clock has not reached the minimum specified
frequency at the termination of reset. A Clock Monitor error
will cause an active low error output on pin G1. This error
output will continue until 16 tC–32 tC clock cycles following
the clock frequency reaching the minimum specified value,
at which time the G1 output will enter the TRI-STATE mode.
The external RC network shown in Figure 6 should be used
to ensure that the RESET pin is held low until the power sup-
ply to the chip stabilizes.
17
www.national.com
Reset (Continued)
R1
R2
C1
C2
(pF)
CKI Freq Conditions
(MHz)
(kΩ) (MΩ) (pF)
0
0
1
1
30
30–36
4
VCC = 5V
200 100–150
0.455
VCC = 2.5V
TABLE 2. RC Oscillator Configuration, TA = 25˚C
R
C
CKI Freq
(MHz)
Instr. Cycle Conditions
(µs)
(kΩ) (pF)
DS012829-7
3.3
5.6
6.8
82
2.2 to 2.7
1.1 to 1.3
0.9 to 1.1
3.7 to 4.6
7.4 to 9.0
8.8 to 10.8
VCC = 5V
VCC = 5V
VCC = 5V
>
RC 5 x Power Supply Rise Time
100
100
FIGURE 6. Recommended Reset Circuit
Note: 3k ≤ R ≤ 200k
50 pF ≤ C ≤ 200 pF
Oscillator Circuits
The chip can be driven by a clock input on the CKI input pin
which can be between DC and 10 MHz. The CKO output
clock is on pin G7 (crystal configuration). The CKI input fre-
quency is divided down by 10 to produce the instruction
cycle clock (1/tc).
CONTROL REGISTERS
CNTRL Register (Address X'00EE)
T1C3 T1C2 T1C1 T1C0 MSEL IEDG
Bit 7
SL1
SL0
Figure 7 shows the Crystal and R/C oscillator diagrams.
Bit 0
CRYSTAL OSCILLATOR
The Timer1 (T1) and MICROWIRE/PLUS control register
contains the following bits:
CKI and CKO can be connected to make a closed loop crys-
tal (or resonator) controlled oscillator.
T1C3
T1C2
T1C1
T1C0
Timer T1 mode control bit
Timer T1 mode control bit
Timer T1 mode control bit
Timer T1 Start/Stop control in timer
Table 1 shows the component values required for various
standard crystal values.
R/C OSCILLATOR
modes 1 and 2, T1 Underflow Interrupt
Pending Flag in timer mode 3
By selecting CKI as a single pin oscillator input, a single pin
R/C oscillator circuit can be connected to it. CKO is available
as a general purpose input, and/or HALT restart input.
MSEL
IEDG
Selects G5 and G4 as MICROWIRE/PLUS
signals SK and SO respectively
Table 2 shows the variation in the oscillator frequencies as
functions of the component (R and C) values.
External interrupt edge polarity select
(0 = Rising edge, 1 = Falling edge)
SL1 & SL0 Select the MICROWIRE/PLUS clock divide
by (00 = 2, 01 = 4, 1x = 8)
PSW Register (Address X'00EF)
HC
C
T1PNDA T1ENA EXPND BUSY EXEN GIE
Bit 0
Bit 7
The PSW register contains the following select bits:
HC
C
Half Carry Flag
Carry Flag
DS012829-8
T1PNDA Timer T1 Interrupt Pending Flag (Autoreload
RA in mode 1, T1 Underflow in Mode 2, T1A
capture edge in mode 3)
T1ENA
Timer T1 Interrupt Enable for Timer Underflow
or T1A Input capture edge
EXPND External interrupt pending
BUSY
EXEN
GIE
MICROWIRE/PLUS busy shifting flag
DS012829-9
Enable external interrupt
FIGURE 7. Crystal and R/C Oscillator Diagrams
Global interrupt enable (enables interrupts)
The Half-Carry flag is also affected by all the instructions that
affect the Carry flag. The SC (Set Carry) and R/C (Reset
Carry) instructions will respectively set or clear both the carry
flags. In addition to the SC and R/C instructions, ADC,
SUBC, RRC and RLC instructions affect the Carry and Half
Carry flags.
TABLE 1. Crystal Oscillator Configuration, TA = 25˚C
R1
(kΩ) (MΩ) (pF)
30
R2
C1
C2
(pF)
CKI Freq Conditions
(MHz)
0
1
30–36
10
VCC = 5V
www.national.com
18
CONTROL REGISTERS (Continued)
Timers
These devices contain a very versatile set of timers (T0, T1,
T2, T3 for all except the CS series, which only use T0 and
T1). All timers and associated autoreload/capture registers
power up containing random data.
ICNTRL Register (Address X'00E8)
Reserved
Bit 7
LPEN
T0PND
T0EN µWPND µWEN T1PNDB
T1ENB
Bit 0
The ICNTRL register contains the following bits:
Reserved This bit is reserved and should be zero
TIMER T0 (IDLE TIMER)
The device supports applications that require maintaining
real time and low power with the IDLE mode. This IDLE
mode support is furnished by the IDLE timer T0, which is a
16-bit timer. The Timer T0 runs continuously at the fixed rate
of the instruction cycle clock, tc. The user cannot read or
write to the IDLE Timer T0, which is a count down timer.
LPEN
L Port Interrupt Enable (Multi-Input Wakeup/
Interrupt)
T0PND
T0EN
Timer T0 Interrupt pending
Timer T0 Interrupt Enable (Bit 12 toggle)
MICROWIRE/PLUS interrupt pending
Enable MICROWIRE/PLUS interrupt
µWPND
µWEN
The Timer T0 supports the following functions:
j
j
j
Exit out of the Idle Mode (See Idle Mode description)
WATCHDOG logic (See WATCHDOG description)
Start up delay out of the HALT mode
T1PNDB Timer T1 Interrupt Pending Flag for T1B cap-
ture edge
T1ENB
Timer T1 Interrupt Enable for T1B Input cap-
ture edge
The IDLE Timer T0 can generate an interrupt when the thir-
teenth bit toggles. This toggle is latched into the T0PND
pending flag, and will occur every 4 ms at the maximum
clock frequency (tc = 1 µs). A control flag T0EN allows the in-
terrupt from the thirteenth bit of Timer T0 to be enabled or
disabled. Setting T0EN will enable the interrupt, while reset-
ting it will disable the interrupt.
T2CNTRL Register (Address X'00C6)
T2C3
Bit 7
T2C2
T2C1
T2C0
T2PNDA
T2ENA
T2PNDB
T2ENB
Bit 0
The T2CNTRL control register contains the following bits:
T2C3
T2C2
T2C1
T2C0
Timer T2 mode control bit
Timer T2 mode control bit
Timer T2 mode control bit
TIMER T1, TIMER T2 AND TIMER T3
These devices can have a set of up to three powerful timer/
counter blocks, T1, T2 and T3. The associated features and
functioning of a timer block are described by referring to the
timer block Tx. Since the three timer blocks, T1, T2 and T3
are identical, all comments are equally applicable to any of
the three timer blocks.
Timer T2 Start/Stop control in timer
modes 1 and 2, T2 Underflow Interrupt Pend-
ing Flag in timer mode 3
T2PNDA Timer T2 Interrupt Pending Flag (Autoreload
RA in mode 1, T2 Underflow in mode 2, T2A
capture edge in mode 3)
Each timer block consists of a 16-bit timer, Tx, and two sup-
porting 16-bit autoreload/capture registers, RxA and RxB.
Each timer block has two pins associated with it, TxA and
TxB. The pin TxA supports I/O required by the timer block,
while the pin TxB is an input to the timer block. The powerful
and flexible timer block allows the device to easily perform all
timer functions with minimal software overhead. The timer
block has three operating modes: Processor Independent
PWM mode, External Event Counter mode, and Input Cap-
ture mode.
T2ENA
Timer T2 Interrupt Enable for Timer Underflow
or T2A Input capture edge
T2PNDB Timer T2 Interrupt Pending Flag for T2B cap-
ture edge
T2ENB
Timer T2 Interrupt Enable for Timer Underflow
or T2B Input capture edge
Note: The T2CNTRL register is not available on the CS series.
T3CNTRL Register (Address X'00B6)
The control bits TxC3, TxC2, and TxC1 allow selection of the
different modes of operation.
T3C3
Bit 7
T3C2
T3C1
T3C0
T3PNDA
T3ENA
T3PNDB
T3ENB
Bit 0
Mode 1. Processor Independent PWM Mode
The T3CNTRL control register contains the following bits:
As the name suggests, this mode allows the device to gen-
erate a PWM signal with very minimal user intervention. The
user only has to define the parameters of the PWM signal
(ON time and OFF time). Once begun, the timer block will
continuously generate the PWM signal completely indepen-
dent of the microcontroller. The user software services the
timer block only when the PWM parameters require updat-
ing.
T3C3
T3C2
T3C1
T3C0
Timer T3 mode control bit
Timer T3 mode control bit
Timer T3 mode control bit
Timer T3 Start/Stop control in timer
modes 1 and 2, T3 Underflow Interrupt Pend-
ing Flag in timer mode 3
T3PNDA Timer T3 Interrupt Pending Flag (Autoreload
RA in mode 1, T3 Underflow in mode 2, T3A
capture edge in mode 3)
In this mode the timer Tx counts down at a fixed rate of tc.
Upon every underflow the timer is alternately reloaded with
the contents of supporting registers, RxA and RxB. The very
first underflow of the timer causes the timer to reload from
the register RxA. Subsequent underflows cause the timer to
be reloaded from the registers alternately beginning with the
register RxB.
T3ENA
Timer T3 Interrupt Enable for Timer Underflow
or T3A Input capture edge
T3PNDB Timer T3 Interrupt Pending Flag for T3B cap-
ture edge
T3ENB
Timer T3 Interrupt Enable for Timer Underflow
or T3B Input capture edge
The Tx Timer control bits, TxC3, TxC2 and TxC1 set up the
timer for PWM mode operation.
Note: The T3CNTRL regoster os mpt avao;ab;e pm tje CS series.
Figure 8 shows a block diagram of the timer in PWM mode.
19
www.national.com
Timers (Continued)
The underflows can be programmed to toggle the TxA output
pin. The underflows can also be programmed to generate in-
terrupts.
Underflows from the timer are alternately latched into two
pending flags, TxPNDA and TxPNDB. The user must reset
these pending flags under software control. Two control en-
able flags, TxENA and TxENB, allow the interrupts from the
timer underflow to be enabled or disabled. Setting the timer
enable flag TxENA will cause an interrupt when a timer un-
derflow causes the RxA register to be reloaded into the timer.
Setting the timer enable flag TxENB will cause an interrupt
when a timer underflow causes the RxB register to be re-
loaded into the timer. Resetting the timer enable flags will
disable the associated interrupts.
DS012829-11
FIGURE 9. Timer in External Event Counter Mode
Either or both of the timer underflow interrupts may be en-
abled. This gives the user the flexibility of interrupting once
per PWM period on either the rising or falling edge of the
PWM output. Alternatively, the user may choose to interrupt
on both edges of the PWM output.
Mode 3. Input Capture Mode
The device can precisely measure external frequencies or
time external events by placing the timer block, Tx, in the in-
put capture mode.
In this mode, the timer Tx is constantly running at the fixed tc
rate. The two registers, RxA and RxB, act as capture regis-
ters. Each register acts in conjunction with a pin. The register
RxA acts in conjunction with the TxA pin and the register RxB
acts in conjunction with the TxB pin.
The timer value gets copied over into the register when a
trigger event occurs on its corresponding pin. Control bits,
TxC3, TxC2 and TxC1, allow the trigger events to be speci-
fied either as a positive or a negative edge. The trigger con-
dition for each input pin can be specified independently.
The trigger conditions can also be programmed to generate
interrupts. The occurrence of the specified trigger condition
on the TxA and TxB pins will be respectively latched into the
pending flags, TxPNDA and TxPNDB. The control flag Tx-
ENA allows the interrupt on TxA to be either enabled or dis-
abled. Setting the TxENA flag enables interrupts to be gener-
ated when the selected trigger condition occurs on the TxA
pin. Similarly, the flag TxENB controls the interrupts from the
TxB pin.
DS012829-10
FIGURE 8. Timer in PWM Mode
Mode 2. External Event Counter Mode
This mode is quite similar to the processor independent
PWM mode described above. The main difference is that the
timer, Tx, is clocked by the input signal from the TxA pin. The
Tx timer control bits, TxC3, TxC2 and TxC1 allow the timer to
be clocked either on a positive or negative edge from the
TxA pin. Underflows from the timer are latched into the TxP-
NDA pending flag. Setting the TxENA control flag will cause
an interrupt when the timer underflows.
Underflows from the timer can also be programmed to gen-
erate interrupts. Underflows are latched into the timer TxC0
pending flag (the TxC0 control bit serves as the timer under-
flow interrupt pending flag in the Input Capture mode). Con-
sequently, the TxC0 control bit should be reset when enter-
ing the Input Capture mode. The timer underflow interrupt is
enabled with the TxENA control flag. When a TxA interrupt
occurs in the Input Capture mode, the user must check both
the TxPNDA and TxC0 pending flags in order to determine
whether a TxA input capture or a timer underflow (or both)
caused the interrupt.
In this mode the input pin TxB can be used as an indepen-
dent positive edge sensitive interrupt input if the TxENB con-
trol flag is set. The occurrence of a positive edge on the TxB
input pin is latched into the TxPNDB flag.
Figure 9 shows a block diagram of the timer in External
Event Counter mode.
Figure 10 shows a block diagram of the timer in Input Cap-
ture mode.
Note: The PWM output is not available in this mode since the TxA pin is being
used as the counter input clock.
www.national.com
20
Timers (Continued)
DS012829-12
FIGURE 10. Timer in Input Capture Mode
TIMER CONTROL FLAGS
The control bits and their functions are summarized below.
TxC3
TxC2
TxC1
TxC0
Timer mode control
Timer mode control
Timer mode control
Timer Start/Stop control in Modes 1 and 2 (Pro-
cessor Independent PWM and External Event
Counter), where 1 = Start, 0 = Stop
Timer Underflow Interrupt Pending Flag in
Mode 3 (Input Capture)
TxPNDA Timer Interrupt Pending Flag
TxENA
Timer Interrupt Enable Flag
1 = Timer Interrupt Enabled
0 = Timer Interrupt Disabled
TxPNDB Timer Interrupt Pending Flag
TxENB
Timer Interrupt Enable Flag
1 = Timer Interrupt Enabled
0 = Timer Interrupt Disabled
21
www.national.com
Timers (Continued)
The timer mode control bits (TxC3, TxC2 and TxC1) are detailed below:
Interrupt A
Source
Interrupt B
Source
Timer
Mode
TxC3
TxC2
TxC1
Description
Counts On
1
1
0
0
1
0
PWM: TxA Toggle
Autoreload RA
Autoreload RA
Autoreload RB
Autoreload RB
tC
1
PWM: No TxA
Toggle
tC
0
0
0
0
0
1
0
1
0
External Event
Counter
Timer
Underflow
Pos. TxB Edge
Pos. TxB Edge
Pos. TxB Edge
Pos. TxA
Edge
2
External Event
Counter
Timer
Underflow
Pos. TxA
Edge
Captures:
Pos. TxA Edge
or Timer
tC
tC
tC
tC
TxA Pos. Edge
TxB Pos. Edge
Captures:
Underflow
1
0
1
1
1
1
0
1
1
Pos. TxA
Neg. TxB
Edge
TxA Pos. Edge
TxB Neg. Edge
Captures:
Edge or Timer
Underflow
3
Neg. TxA
Neg. TxB
Edge
TxA Neg. Edge
TxB Neg. Edge
Captures:
Edge or Timer
Underflow
Neg. TxA
Neg. TxB
Edge
TxA Neg. Edge
TxB Neg. Edge
Edge or Timer
Underflow
running immediately since crystal oscillators and ceramic
resonators have a delayed start up time to reach full ampli-
tude and frequency stability. The IDLE timer is used to gen-
erate a fixed delay to ensure that the oscillator has indeed
stabilized before allowing instruction execution. In this case,
upon detecting a valid Wakeup signal, only the oscillator cir-
cuitry is enabled. The IDLE timer is loaded with a value of
256 and is clocked with the tc instruction cycle clock. The tc
clock is derived by dividing the oscillator clock down by a fac-
tor of 10. The Schmitt trigger following the CKI inverter on
the chip ensures that the IDLE timer is clocked only when the
oscillator has a sufficiently large amplitude to meet the
Schmitt trigger specifications. This Schmitt trigger is not part
of the oscillator closed loop. The startup timeout from the
IDLE timer enables the clock signals to be routed to the rest
of the chip.
Power Save Modes
The device offers the user two power save modes of opera-
tion: HALT and IDLE. In the HALT mode, all microcontroller
activities are stopped. In the IDLE mode, the on-board oscil-
lator circuitry and timer T0 are active but all other microcon-
troller activities are stopped. In either mode, all on-board
RAM, registers, I/O states, and timers (with the exception of
T0) are unaltered.
HALT MODE
The device can be placed in the HALT mode by writing a “1”
to the HALT flag (G7 data bit). All microcontroller activities,
including the clock and timers, are stopped. The WATCH-
DOG logic on the device is disabled during the HALT mode.
However, the clock monitor circuitry if enabled remains ac-
tive and will cause the WATCHDOG output pin (WDOUT) to
go low. If the HALT mode is used and the user does not want
to activate the WDOUT pin, the Clock Monitor should be dis-
abled after the device comes out of reset (resetting the Clock
Monitor control bit with the first write to the WDSVR register).
In the HALT mode, the power requirements of the device are
minimal and the applied voltage (VCC) may be decreased to
Vr (Vr = 2.0V) without altering the state of the machine.
If an RC clock option is being used, the fixed delay is intro-
duced optionally. A control bit, CLKDLY, mapped as configu-
ration bit G7, controls whether the delay is to be introduced
or not. The delay is included if CLKDLY is set, and excluded
if CLKDLY is reset. The CLKDLY bit is cleared on reset.
The device has two mask options associated with the HALT
mode. The first mask option enables the HALT mode feature,
while the second mask option disables the HALT mode. With
the HALT mode enable mask option, the device will enter
and exit the HALT mode as described above. With the HALT
disable mask option, the device cannot be placed in the
HALT mode (writing a “1” to the HALT flag will have no effect,
the HALT flag will remain “0”).
The device supports three different ways of exiting the HALT
mode. The first method of exiting the HALT mode is with the
Multi-Input Wakeup feature on the L port. The second
method is with a low to high transition on the CKO (G7) pin.
This method precludes the use of the crystal clock configura-
tion (since CKO becomes a dedicated output), and so may
only be used with an RC clock configuration. The third
method of exiting the HALT mode is by pulling the RESET
pin low.
IDLE MODE
The device is placed in the IDLE mode by writing a “1” to the
IDLE flag (G6 data bit). In this mode, all activities, except the
associated on-board oscillator circuitry and the IDLE Timer
T0, are stopped. The power supply requirements of the
Since a crystal or ceramic resonator may be selected as the
oscillator, the Wakeup signal is not allowed to start the chip
www.national.com
22
device will first execute the Timer T0 interrupt service routine
and then return to the instruction following the “Enter Idle
Mode” instruction.
Power Save Modes (Continued)
micro-controller in this mode of operation are typically
around 30% of normal power requirement of the microcon-
troller.
Alternatively, the user can enter the IDLE mode with the
IDLE Timer T0 interrupt disabled. In this case, the device will
resume normal operation with the instruction immediately
following the “Enter IDLE Mode” instruction.
Note: It is necessary to program two NOP instructions following both the set
HALT mode and set IDLE mode instructions. These NOP instructions
are necessary to allow clock resynchronization following the HALT or
IDLE modes.
As with the HALT mode, the device can be returned to nor-
mal operation with a reset, or with a Multi-Input Wakeup from
the L Port. Alternately, the microcontroller resumes normal
operation from the IDLE mode when the thirteenth bit (repre-
senting 4.096 ms at internal clock frequency of 10 MHz, tc =
1 µs) of the IDLE Timer toggles.
This toggle condition of the thirteenth bit of the IDLE Timer
T0 is latched into the T0PND pending flag.
Multi-Input Wakeup
The Multi-Input Wakeup feature is ued to return (wakeup) the
device from either the HALT or IDLE modes. Alternately
Multi-Input Wakeup/Interrupt feature may also be used to
generate up to 8 edge selectable external interrupts.
The user has the option of being interrupted with a transition
on the thirteenth bit of the IDLE Timer T0. The interrupt can
be enabled or disabled via the T0EN control bit. Setting the
T0EN flag enables the interrupt and vice versa.
Figure 11 shows the Multi-Input Wakeup logic.
The user can enter the IDLE mode with the Timer T0 inter-
rupt enabled. In this case, when the T0PND bit gets set, the
DS012829-13
FIGURE 11. Multi-Input Wake Up Logic
The Multi-Input Wakeup feature utilizes the L Port. The user
selects which particular L port bit (or combination of L Port
bits) will cause the device to exit the HALT or IDLE modes.
The selection is done through the Register WKEN. The Reg-
ister WKEN is an 8-bit read/write register, which contains a
control bit for every L port bit. Setting a particular WKEN bit
enables a Wakeup from the associated L port pin.
an edge select entails several steps in order to avoid a
Wakeup condition as a result of the edge change. First, the
associated WKEN bit should be reset, followed by the edge
select change in WKEDG. Next, the associated WKPND bit
should be cleared, followed by the associated WKEN bit be-
ing re-enabled.
An example may serve to clarify this procedure. Suppose we
wish to change the edge select from positive (low going high)
to negative (high going low) for L Port bit 5, where bit 5 has
previously been enabled for an input interrupt. The program
would be as follows:
The user can select whether the trigger condition on the se-
lected L Port pin is going to be either a positive edge (low to
high transition) or a negative edge (high to low transition).
This selection is made via the Register WKEDG, which is an
8-bit control register with a bit assigned to each L Port pin.
Setting the control bit will select the trigger condition to be a
negative edge on that particular L Port pin. Resetting the bit
selects the trigger condition to be a positive edge. Changing
RBIT 5, WKEN
; Disable MIWU
SBIT 5, WKEDG ; Change edge polarity
RBIT 5, WKPND ; Reset pending flag
SBIT 5, WKEN
; Enable MIWU
23
www.national.com
The Wakeup signal will not start the chip running immedi-
ately since crystal oscillators or ceramic resonators have a fi-
nite start up time. The IDLE Timer (T0) generates a fixed de-
lay to ensure that the oscillator has indeed stabilized before
allowing the device to execute instructions. In this case,
upon detecting a valid Wakeup signal, only the oscillator cir-
cuitry and the IDLE Timer T0 are enabled. The IDLE Timer is
Multi-Input Wakeup (Continued)
If the L port bits have been used as outputs and then
changed to inputs with Multi-Input Wakeup/Interrupt, a safety
procedure should also be followed to avoid wakeup condi-
tions. After the selected L port bits have been changed from
output to input but before the associated WKEN bits are en-
abled, the associated edge select bits in WKEDG should be
set or reset for the desired edge selects, followed by the as-
sociated WKPND bits being cleared.
loaded with a value of 256 and is clocked from the t
c instruc-
tion cycle clock. The tc clock is derived by dividing down the
oscillator clock by a factor of 10. A Schmitt trigger following
the CKI on-inverter ensures that the IDLE timer is clocked
only when the oscillator has a sufficiently large amplitude to
meet the Schmitt trigger specifications. This Schmitt trigger
is not part of the oscillator closed loop. The start-up time-out
from the IDLE timer enables the clock signals to be routed to
the rest of the chip.
This same procedure should be used following reset, since
the L port inputs are left floating as a result of reset.
The occurrence of the selected trigger condition for
Multi-Input Wakeup is latched into a pending register called
WKPND. The respective bits of the WKPND register will be
set on the occurrence of the selected trigger edge on the cor-
responding Port L pin. The user has the responsibility of
clearing these pending flags. Since WKPND is a pending
register for the occurrence of selected wakeup conditions,
the device will not enter the HALT mode if any Wakeup bit is
both enabled and pending. Consequently, the user must
clear the pending flags before attempting to enter the HALT
mode.
If the RC clock option is used, the fixed delay is under soft-
ware control. A control flag, CLKDLY, in the G7 configuration
bit allows the clock start up delay to be optionally inserted.
Setting CLKDLY flag high will cause clock start up delay to
be inserted and resetting it will exclude the clock start up de-
lay. The CLKDLY flag high will cause clock start up delay.
The CLKDLY flag is cleared during reset, so the clock start
up delay is not present following reset with the RC clock op-
tions.
WKEN, WKPND and WKEDG are all read/write registers,
and are cleared at reset.
USART
PORT L INTERRUPTS
Port L provides the user with an additional eight fully select-
able, edge sensitive interrupts which are all vectored into the
same service subroutine.
The device contains a full-duplex software programmable
USART. The USART (Figure 12) consists of a transmit shift
register, a receive shift register and seven addressable reg-
isters, as follows: a transmit buffer register (TBUF), a re-
ceiver buffer register (RBUF), a USART control and status
register (ENU), a USART receive control and status register
(ENUR), a USART interrupt and clock source register
(ENUI), a prescaler select register (PSR) and baud (BAUD)
register. The ENU register contains flags for transmit and re-
ceive functions; this register also determines the length of
the data frame (7, 8 or 9 bits), the value of the ninth bit in
transmission, and parity selection bits. The ENUR register
flags framing, data overrun and parity errors while the US-
ART is receiving.
The interrupt from Port L shares logic with the wake up cir-
cuitry. The register WKEN allows interrupts from Port L to be
individually enabled or disabled. The register WKEDG speci-
fies the trigger condition to be either a positive or a negative
edge. Finally, the register WKPND latches in the pending
trigger conditions.
The GIE (Global Interrupt Enable) bit enables the interrupt
function.
A control flag, LPEN, functions as a global interrupt enable
for Port L interrupts. Setting the LPEN flag will enable inter-
rupts and vice versa. A separate global pending flag is not
needed since the register WKPND is adequate.
Other functions of the ENUR register include saving the
ninth bit received in the data frame, enabling or disabling the
USART’s attention mode of operation and providing addi-
tional receiver/transmitter status information via RCVG and
XMTG bits. The determination of an internal or external clock
source is done by the ENUI register, as well as selecting the
number of stop bits and enabling or disabling transmit and
receive interrupts. A control flag in this register can also se-
lect the USART mode of operation: asynchronous or
synchronous.
Since Port L is also used for waking the device out of the
HALT or IDLE modes, the user can elect to exit the HALT or
IDLE modes either with or without the interrupt enabled. If he
elects to disable the interrupt, then the device will restart ex-
ecution from the instruction immediately following the in-
struction that placed the microcontroller in the HALT or IDLE
modes. In the other case, the device will first execute the in-
terrupt service routine and then revert to normal operation.
(See HALT MODE for clock option wakeup information.)
www.national.com
24
USART (Continued)
DS012829-14
FIGURE 12. USART Block Diagram
USART CONTROL AND STATUS REGISTERS
PEN = 1
Parity enabled.
The operation of the USART is programmed through three
registers: ENU, ENUR and ENUI.
PSEL1, PSEL0: Parity select bits. Read/Write, cleared on
reset.
PSEL1 = 0, PSEL0 = 0
PSEL1 = 0, PSEL0 = 1
PSEL1 = 1, PSEL0 = 0
PSEL1 = 1, PSEL0 = 1
Odd Parity (if Parity enabled)
Even Parity (if Parity enabled)
Mark(1) (if Parity enabled)
Space(0) (if Parity enabled)
DESCRIPTION OF USART REGISTER BITS
ENU-USART Control and Status Register (Address at 0BA)
PEN PSEL1 XBIT9/ CHL1
CHL0
ERR
RBFL TBMT
PSEL0
XBIT9/PSEL0: Programs the ninth bit for transmission when
the USART is operating with nine data bits per frame. For
seven or eight data bits per frame, this bit in conjunction with
PSEL1 selects parity. Read/Write, cleared on reset.
Bit 7
Bit 0
PEN: This bit enables/disables Parity (7- and 8-bit modes
only). Read/Write, cleared on reset.
PEN = 0
Parity disabled.
25
www.national.com
RCVG: This bit is set high whenever a framing error occurs
and goes low when RDX goes high. Read only, cleared on
reset.
USART (Continued)
CHL1, CHL0: These bits select the character frame format.
Parity is not included and is generated/verified by hardware.
Read/Write, cleared on reset.
ENUI-USART Interrupt and Clock Source Register
(Address at 0BC)
CHL1 = 0, CHL0 = 0
CHL1 = 0, CHL0 = 1
The frame contains eight data bits.
STP2 STP78 ETDX SSEL XRCLK XTCLK
Bit 7
ERI
ETI
The frame contains seven data
bits.
Bit 0
STP2: This bit programs the number of Stop bits to be trans-
mitted. Read/Write, cleared on reset.
CHL1 = 1, CHL0 = 0
CHL1 = 1, CHL0 = 1
The frame contains nine data bits.
Loopback Mode selected. Trans-
mitter output internally looped back
to receiver input. Nine bit framing
format is used.
STP2 = 0
STP2 = 1
One Stop bit transmitted.
Two Stop bits transmitted.
STP78: This bit is set to program the last Stop bit to be 7/8th
ERR: This bit is a global USART error flag which gets set if
any or a combination of the errors (DOE, FE, PE) occur.
Read only; it cannot be written by software, cleared on reset.
of a bit in length. Read/Write, cleared on reset.
ETDX: TDX (USART Transmit Pin) is the alternate function
assigned to Port L pin L2; it is selected by setting ETDX bit.
To simulate line break generation, software should reset
ETDX bit and output logic zero to TDX pin through Port L
data and configuration registers. Read/Write, cleared on re-
set.
RBFL: This bit is set when the USART has received a com-
plete character and has copied it into the RBUF register. It is
automatically reset when software reads the character from
RBUF. Read only; it cannot be written by software, cleared
on reset.
SSEL: USART mode select. Read/Write, cleared on reset.
TBMT: This bit is set when the USART transfers a byte of
data from the TBUF register into the TSFT register for trans-
mission. It is automatically reset when software writes into
the TBUF register. Read only, bit is set to “one” on reset; it
cannot be written by software.
SSEL = 0
SSEL = 1
Asynchronous Mode.
Synchronous Mode.
XRCLK: This bit selects the clock source for the receiver
section. Read/Write, cleared on reset.
XRCLK = 0
The clock source is selected through the
PSR and BAUD registers.
ENUR-USART Receive Control and Status Register
(Address at 0BB)
XRCLK = 1
Signal on CKX (L1) pin is used as the clock.
DOE FE PE Reserved RBIT9 ATTN XMTG RCVG
(Note 12)
XTCLK: This bit selects the clock source for the transmitter
section. Read/Write, cleared on reset.
Bit 7
Bit 0
XTCLK = 0
The clock source is selected through the
PSR and BAUD registers.
Note 12: Bit is reserved for future use. User must set to zero.
XTCLK = 1
Signal on CKX (L1) pin is used as the clock.
DOE: Flags a Data Overrun Error. Read only, cleared on
read, cleared on reset.
ERI: This bit enables/disables interrupt from the receiver
section. Read/Write, cleared on reset.
DOE = 0
Indicates no Data Overrun Error has been de-
tected since the last time the ENUR register
was read.
ERI = 0
ERI = 1
Interrupt from the receiver is disabled.
Interrupt from the receiver is enabled.
DOE = 1
Indicates the occurrence of a Data Overrun Er-
ror.
ETI: This bit enables/disables interrupt from the transmitter
section. Read/Write, cleared on reset.
FE: Flags a Framing Error. Read only, cleared on read,
cleared on reset.
ETI = 0
ETI = 1
Interrupt from the transmitter is disabled.
Interrupt from the transmitter is enabled.
FE = 0
FE = 1
Indicates no Framing Error has been detected
since the last time the ENUR register was read.
Associated I/O Pins
Indicates the occurrence of a Framing Error.
Data is transmitted on the TDX pin and received on the RDX
pin. TDX is the alternate function assigned to Port L pin L2;
it is selected by setting ETDX (in the ENUI register) to one.
RDX is an inherent function of Port L pin L3, requiring no
setup.
PE: Flags a Parity Error. Read only, cleared on read, cleared
on reset.
PE = 0
Indicates no Parity Error has been detected since
the last time the ENUR register was read.
PE = 1
Indicates the occurrence of a Parity Error.
The baud rate clock for the USART can be generated
on-chip, or can be taken from an external source. Port L pin
L1 (CKX) is the external clock I/O pin. The CKX pin can be
either an input or an output, as determined by Port L Con-
figuration and Data registers (Bit 1). As an input, it accepts a
clock signal which may be selected to drive the transmitter
and/or receiver. As an output, it presents the internal Baud
Rate Generator output.
SPARE: Reserved for future use. Read/Write, cleared on re-
set.
RBIT9: Contains the ninth data bit received when the US-
ART is operating with nine data bits per frame. Read only,
cleared on reset.
ATTN: ATTENTION Mode is enabled while this bit is set.
This bit is cleared automatically on receiving a character with
data bit nine set. Read/Write, cleared on reset.
XMTG: This bit is set to indicate that the USART is transmit-
ting. It gets reset at the end of the last frame (end of last Stop
bit). Read only, cleared on reset.
www.national.com
26
output at the CKX pin. The internal baud rate generator is
used to produce the synchronous clock. Data transmit and
receive are performed synchronously with this clock.
USART Operation
The USART has two modes of operation: asynchronous
mode and synchronous mode.
FRAMING FORMATS
ASYNCHRONOUS MODE
The USART supports several serial framing formats (Figure
13). The format is selected using control bits in the ENU,
ENUR and ENUI registers.
This mode is selected by resetting the SSEL (in the ENUI
register) bit to zero. The input frequency to the USART is 16
times the baud rate.
The first format (1, 1a, 1b, 1c) for data transmission (CHL0 =
1, CHL1 = 0) consists of Start bit, seven Data bits (excluding
parity) and 7/8, one or two Stop bits. In applications using
parity, the parity bit is generated and verified by hardware.
The TSFT and TBUF registers double-buffer data for trans-
mission. While TSFT is shifting out the current character on
the TDX pin, the TBUF register may be loaded by software
with the next byte to be transmitted. When TSFT finishes
transmitting the current character the contents of TBUF are
transferred to the TSFT register and the Transmit Buffer
Empty Flag (TBMT in the ENU register) is set. The TBMT
flag is automatically reset by the USART when software
loads a new character into the TBUF register. There is also
the XMTG bit which is set to indicate that the USART is
transmitting. This bit gets reset at the end of the last frame
(end of last Stop bit). TBUF is a read/write register.
The second format (CHL0 = 0, CHL1 = 0) consists of one
Start bit, eight Data bits (excluding parity) and 7/8, one or
two Stop bits. Parity bit is generated and verified by hard-
ware.
The third format for transmission (CHL0 = 0, CHL1 = 1) con-
sists of one Start bit, nine Data bits and 7/8, one or two Stop
bits. This format also supports the USART “ATTENTION”
feature. When operating in this format, all eight bits of TBUF
and RBUF are used for data. The ninth data bit is transmitted
and received using two bits in the ENU and ENUR registers,
called XBIT9 and RBIT9. RBIT9 is a read only bit. Parity is
not generated or verified in this mode.
The RSFT and RBUF registers double-buffer data being re-
ceived. The USART receiver continually monitors the signal
on the RDX pin for a low level to detect the beginning of a
Start bit. Upon sensing this low level, it waits for half a bit
time and samples again. If the RDX pin is still low, the re-
ceiver considers this to be a valid Start bit, and the remaining
bits in the character frame are each sampled a single time, at
the mid-bit position. Serial data input on the RDX pin is
shifted into the RSFT register. Upon receiving the complete
character, the contents of the RSFT register are copied into
the RBUF register and the Received Buffer Full Flag (RBFL)
is set. RBFL is automatically reset when software reads the
character from the RBUF register. RBUF is a read only reg-
ister. There is also the RCVG bit which is set high when a
framing error occurs and goes low once RDX goes high.
TBMT, XMTG, RBFL and RCVG are read only bits.
For any of the above framing formats, the last Stop bit can
be programmed to be 7/8th of a bit in length. If two Stop bits
are selected and the 7/8th bit is set (selected), the second
Stop bit will be 7/8th of a bit in length.
The parity is enabled/disabled by PEN bit located in the ENU
register. Parity is selected for 7- and 8-bit modes only. If par-
ity is enabled (PEN = 1), the parity selection is then per-
formed by PSEL0 and PSEL1 bits located in the ENU regis-
ter.
Note that the XBIT9/PSEL0 bit located in the ENU register
serves two mutually exclusive functions. This bit programs
the ninth bit for transmission when the USART is operating
with nine data bits per frame. There is no parity selection in
this framing format. For other framing formats XBIT9 is not
needed and the bit is PSEL0 used in conjunction with PSEL1
to select parity.
SYNCHRONOUS MODE
In this mode data is transferred synchronously with the
clock. Data is transmitted on the rising edge and received on
the falling edge of the synchronous clock.
The frame formats for the receiver differ from the transmitter
in the number of Stop bits required. The receiver only re-
quires one Stop bit in a frame, regardless of the setting of the
Stop bit selection bits in the control register. Note that an im-
plicit assumption is made for full duplex USART operation
that the framing formats are the same for the transmitter and
receiver.
This mode is selected by setting SSEL bit in the ENUI regis-
ter. The input frequency to the USART is the same as the
baud rate.
When an external clock input is selected at the CKX pin, data
transmit and receive are performed synchronously with this
clock through TDX/RDX pins.
If data transmit and receive are selected with the CKX pin as
clock output, the device generates the synchronous clock
27
www.national.com
USART Operation (Continued)
DS012829-15
FIGURE 13. Framing Formats
USART INTERRUPTS
the basic baud clock is created from the oscillator frequency
through a two-stage divider chain consisting of a 1–16 (in-
crements of 0.5) prescaler and an 11-bit binary counter. (Fig-
ure 14). The divide factors are specified through two read/
write registers shown in Figure 15. Note that the 11-bit Baud
Rate Divisor spills over into the Prescaler Select Register
(PSR). PSR is cleared upon reset.
The USART is capable of generating interrupts. Interrupts
are generated on Receive Buffer Full and Transmit Buffer
Empty. Both interrupts have individual interrupt vectors. Two
bytes of program memory space are reserved for each inter-
rupt vector. The two vectors are located at addresses 0xEC
to 0xEF Hex in the program memory space. The interrupts
can be individually enabled or disabled using Enable Trans-
mit Interrupt (ETI) and Enable Receive Interrupt (ERI) bits in
the ENUI register.
As shown in Table 6, a Prescaler Factor of 0 corresponds to
NO CLOCK. This condition is the USART power down mode
where the USART clock is turned off for power saving pur-
pose. The user must also turn the USART clock off when a
different baud rate is chosen.
The interrupt from the Transmitter is set pending, and re-
mains pending, as long as both the TBMT and ETI bits are
set. To remove this interrupt, software must either clear the
ETI bit or write to the TBUF register (thus clearing the TBMT
bit).
The correspondences between the 5-bit Prescaler Select
and Prescaler factors are shown in Table 6. There are many
ways to calculate the two divisor factors, but one particularly
effective method would be to achieve a 1.8432 MHz fre-
quency coming out of the first stage. The 1.8432 MHz pres-
caler output is then used to drive the software programmable
baud rate counter to create a 16x clock for the following baud
rates: 110, 134.5, 150, 300, 600, 1200, 1800, 2400, 3600,
4800, 7200, 9600, 19200 and 38400 (Table 1). Other baud
rates may be created by using appropriate divisors. The 16x
clock is then divided by 16 to provide the rate for the serial
shift registers of the transmitter and receiver.
The interrupt from the receiver is set pending, and remains
pending, as long as both the RBFL and ERI bits are set. To
remove this interrupt, software must either clear the ERI bit
or read from the RBUF register (thus clearing the RBFL bit).
Baud Clock Generation
The clock inputs to the transmitter and receiver sections of
the USART can be individually selected to come either from
an external source at the CKX pin (port L, pin L1) or from a
source selected in the PSR and BAUD registers. Internally,
www.national.com
28
Baud Clock Generation (Continued)
DS012829-16
FIGURE 14. USART BAUD Clock Generation
DS012829-17
FIGURE 15. USART BAUD Clock Divisor Registers
TABLE 3. Baud Rate Divisors
(1.8432 MHz Prescaler Output)
Prescaler
Select
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
10010
10011
10100
10101
10110
10111
11000
11001
11010
11011
11100
11101
11110
11111
Prescaler
Factor
4.5
5
Baud
Rate
Baud Rate
Divisor − 1
(N-1)
5.5
6
110
1046
(110.03)
6.5
7
134.5
855
(134.58)
7.5
8
150
300
767
383
191
95
63
47
31
23
15
11
5
8.5
9
600
1200
1800
2400
3600
4800
7200
9600
19200
38400
9.5
10
10.5
11
11.5
12
12.5
13
2
13.5
14
Note: The entries in Table 4 assume a prescaler output of 1.8432 MHz. In the
asynchronous mode the baud rate could be as high as 625k.
14.5
15
TABLE 4. Prescaler Factors
Prescaler
Select
00000
00001
00010
00011
00100
00101
00110
00111
Prescaler
15.5
16
Factor
NO CLOCK
1
1.5
2
2.5
3
3.5
4
29
www.national.com
cause of the finite start up time requirement of the crystal os-
cillator. The idle timer (T0) generates a fixed (256 tc) delay to
ensure that the oscillator has indeed stabilized before allow-
ing the device to execute code. The user has to consider this
delay when data transfer is expected immediately after exit-
ing the HALT mode.
Baud Clock Generation (Continued)
As an example, considering Asynchronous Mode and a CKI
clock of 4.608 MHz, the prescaler factor selected is:
4.608/1.8432 = 2.5
The 2.5 entry is available in Table 4. The 1.8432 MHz pres-
caler output is then used with proper Baud Rate Divisor
(Table 3) to obtain different baud rates. For a baud rate of
19200 e.g., the entry in Table 3 is 5.
Diagnostic
Bits CHARL0 and CHARL1 in the ENU register provide a
loopback feature for diagnostic testing of the USART. When
these bits are set to one, the following occur: The receiver in-
put pin (RDX) is internally connected to the transmitter out-
put pin (TDX); the output of the Transmitter Shift Register is
“looped back” into the Receive Shift Register input. In this
mode, data that is transmitted is immediately received. This
feature allows the processor to verify the transmit and re-
ceive data paths of the USART.
N − 1 = 5 (N − 1 is the value from Table 3)
N = 6 (N is the Baud Rate Divisor)
Baud Rate = 1.8432 MHz/(16 x 6) = 19200
The divide by 16 is performed because in the asynchronous
mode, the input frequency to the USART is 16 times the
baud rate. The equation to calculate baud rates is given be-
low.
The actual Baud Rate may be found from:
BR = Fc/(16 x N x P)
Note that the framing format for this mode is the nine bit for-
mat; one Start bit, nine data bits, and 7/8, one or two Stop
bits. Parity is not generated or verified in this mode.
Where:
BR is the Baud Rate
Attention Mode
Fc is the CKI frequency
N is the Baud Rate Divisor (Table 3).
The USART Receiver section supports an alternate mode of
operation, referred to as ATTENTION Mode. This mode of
operation is selected by the ATTN bit in the ENUR register.
The data format for transmission must also be selected as
having nine Data bits and either 7/8, one or two Stop bits.
P is the Prescaler Divide Factor selected by the value in the
Prescaler Select Register (Table 4)
Note: In the Synchronous Mode, the divisor 16 is replaced by two.
Example:
The ATTENTION mode of operation is intended for use in
networking the device with other processors. Typically in
such environments the messages consists of device ad-
dresses, indicating which of several destinations should re-
ceive them, and the actual data. This Mode supports a
scheme in which addresses are flagged by having the ninth
bit of the data field set to a 1. If the ninth bit is reset to a zero
the byte is a Data byte.
Asynchronous Mode:
Crystal Frequency = 5 MHz
Desired baud rate = 9600
Using the above equation N x P can be calculated first.
N x P = (5 x 106)/(16 x 9600) = 32.552
Now 32.552 is divided by each Prescaler Factor (Table 4) to
obtain a value closest to an integer. This factor happens to
be 6.5 (P = 6.5).
While in ATTENTION mode, the USART monitors the com-
munication flow, but ignores all characters until an address
character is received. Upon receiving an address character,
the USART signals that the character is ready by setting the
RBFL flag, which in turn interrupts the processor if USART
Receiver interrupts are enabled. The ATTN bit is also cleared
automatically at this point, so that data characters as well as
address characters are recognized. Software examines the
contents of the RBUF and responds by deciding either to ac-
cept the subsequent data stream (by leaving the ATTN bit re-
set) or to wait until the next address character is seen (by
setting the ATTN bit again).
N = 32.552/6.5 = 5.008 (N = 5)
The programmed value (from Table 3) should be 4 (N − 1).
Using the above values calculated for N and P:
BR = (5 x 106)/(16 x 5 x 6.5) = 9615.384
% error = (9615.385 − 9600)/9600 x 100 = 0.16%
Effect of HALT/IDLE
The USART logic is reinitialized when either the HALT or
IDLE modes are entered. This reinitialization sets the TBMT
flag and resets all read only bits in the USART control and
status registers. Read/Write bits remain unchanged. The
Transmit Buffer (TBUF) is not affected, but the Transmit Shift
register (TSFT) bits are set to one. The receiver registers
RBUF and RSFT are not affected.
Operation of the USART Transmitter is not affected by selec-
tion of this Mode. The value of the ninth bit to be transmitted
is programmed by setting XBIT9 appropriately. The value of
the ninth bit received is obtained by reading RBIT9. Since
this bit is located in ENUR register where the error flags re-
side, a bit operation on it will reset the error flags.
The device will exit from the HALT/IDLE modes when the
Start bit of a character is detected at the RDX (L3) pin. This
feature is obtained by using the Multi-Input Wakeup scheme
provided on the device.
Comparators
The device contains two differential comparators, each with
a pair of inputs (positive and negative) and an output. Ports
I1–I3 and I4–I6 are used for the comparators. The following
is the Port I assignment:
Before entering the HALT or IDLE modes the user program
must select the Wakeup source to be on the RDX pin. This
selection is done by setting bit 3 of WKEN (Wakeup Enable)
register. The Wakeup trigger condition is then selected to be
high to low transition. This is done via the WKEDG register
(Bit 3 is one.)
I6 Comparator2 output
I5 Comparator2 positive input
I4 Comparator2 negative input
I3 Comparator1 output
If the device is halted and crystal oscillator is used, the
Wakeup signal will not start the chip running immediately be-
www.national.com
30
bit are associated with each comparator. The comparator re-
sult bits (CMP1RD and CMP2RD) are read only bits which
will read as zero if the associated comparator is not enabled.
The Comparator Select Register is cleared with reset, result-
ing in the comparators being disabled. The comparators
should also be disabled before entering either the HALT or
IDLE modes in order to save power. The configuration of the
CMPSL register is as follows:
Comparators (Continued)
I2 Comparator1 positive input
I1 Comparator1 negative input
Only Comparator 1 is available on the CS series.
A Comparator Select Register (CMPSL) is used to enable
the comparators, read the outputs of the comparators inter-
nally, and enable the outputs of the comparators to the pins.
Two control bits (enable and output enable) and one result
CMPSL REGISTER (ADDRESS X’00B7)
Reserved
Bit 7
CMP20E
CMP2RD
CMP2EN
CMP10E
CMP1RD
CMP1EN
Reserved
Bit 0
The CMPSL register contains the following bits:
Interrupts
Reserved These bits are reserved and must be zero
INTRODUCTION
CMP20E Selects pin I6 as comparator 2 output provided
that CMP2EN is set to enable the comparator
Each device supports thirteen vectored interrupts. Interrupt
sources include Timer 0, Timer 1, Timer 2, Timer 3, Port L
Wakeup, Software Trap, MICROWIRE/PLUS, and External
Input.
CMP2RD Comparator 2 result (this is a read only bit, which
will read as 0 if the comparator is not enabled)
CMP2EN Enable comparator 2
All interrupts force a branch to location 00FF Hex in program
memory. The VIS instruction may be used to vector to the
appropriate service routine from location 00FF Hex.
CMP10E Selects pin I3 as comparator 1 output provided
that CMPIEN is set to enable the comparator
CMP1RD Comparator 1 result (this is a read only bit, which
will read as 0 if the comparator is not enabled)
The Software trap has the highest priority while the default
VIS has the lowest priority.
CMP1EN Enable comparator 1
Each of the 13 maskable inputs has a fixed arbitration rank-
ing and vector.
Note: For compatibility with existing code and with existing Mask ROMMed
devices the bits of the CMPSL register will take precedence over the
associated Port F configuration and data output bits.
Figure 16 shows the Interrupt Block Diagram.
DS012829-42
FIGURE 16. Interrupt Block Diagram
31
www.national.com
interrupt, and jump to the interrupt handling routine corre-
sponding to the highest priority enabled and active interrupt.
Alternately, the user may choose to poll all interrupt pending
and enable bits to determine the source(s) of the interrupt. If
more than one interrupt is active, the user’s program must
decide which interrupt to service.
Interrupts (Continued)
MASKABLE INTERRUPTS
All interrupts other than the Software Trap are maskable.
Each maskable interrupt has an associated enable bit and
pending flag bit. The pending bit is set to 1 when the interrupt
condition occurs. The state of the interrupt enable bit, com-
bined with the GIE bit determines whether an active pending
flag actually triggers an interrupt. All of the maskable inter-
rupt pending and enable bits are contained in mapped con-
trol registers, and thus can be controlled by the software.
Within a specific interrupt service routine, the associated
pending bit should be cleared. This is typically done as early
as possible in the service routine in order to avoid missing
the next occurrence of the same type of interrupt event.
Thus, if the same event occurs a second time, even while the
first occurrence is still being serviced, the second occur-
rence will be serviced immediately upon return from the cur-
rent interrupt routine.
A maskable interrupt condition triggers an interrupt under the
following conditions:
1. The enable bit associated with that interrupt is set.
2. The GIE bit is set.
An interrupt service routine typically ends with an RETI in-
struction. This instruction sets the GIE bit back to 1, pops the
address stored on the stack, and restores that address to the
program counter. Program execution then proceeds with the
next instruction that would have been executed had there
been no interrupt. If there are any valid interrupts pending,
the highest-priority interrupt is serviced immediately upon re-
turn from the previous interrupt.
3. The device is not processing a non-maskable interrupt.
(If
a non-maskable interrupt is being serviced, a
maskable interrupt must wait until that service routine is
completed.)
An interrupt is triggered only when all of these conditions are
met at the beginning of an instruction. If different maskable
interrupts meet these conditions simultaneously, the highest
priority interrupt will be serviced first, and the other pending
interrupts must wait.
VIS INSTRUCTION
The general interrupt service routine, which starts at address
00FF Hex, must be capable of handling all types of inter-
rupts. The VIS instruction, together with an interrupt vector
table, directs the device to the specific interrupt handling rou-
tine based on the cause of the interrupt.
Upon Reset, all pending bits, individual enable bits, and the
GIE bit are reset to zero. Thus, a maskable interrupt condi-
tion cannot trigger an interrupt until the program enables it by
setting both the GIE bit and the individual enable bit. When
enabling an interrupt, the user should consider whether or
not a previously activated (set) pending bit should be ac-
knowledged. If, at the time an interrupt is enabled, any pre-
vious occurrences of the interrupt should be ignored, the as-
sociated pending bit must be reset to zero prior to enabling
the interrupt. Otherwise, the interrupt may be simply en-
abled; if the pending bit is already set, it will immediately trig-
ger an interrupt. A maskable interrupt is active if its associ-
ated enable and pending bits are set.
VIS is a single-byte instruction, typically used at the very be-
ginning of the general interrupt service routine at address
00FF Hex, or shortly after that point, just after the code used
for context switching. The VIS instruction determines which
enabled and pending interrupt has the highest priority, and
causes an indirect jump to the address corresponding to that
interrupt source. The jump addresses (vectors) for all pos-
sible interrupts sources are stored in a vector table.
The vector table may be as long as 32 bytes (maximum of 16
vectors) and resides at the top of the 256-byte block contain-
ing the VIS instruction. However, if the VIS instruction is at
the very top of a 256-byte block (such as at 00FF Hex), the
vector table resides at the top of the next 256-byte block.
Thus, if the VIS instruction is located somewhere between
00FF and 01DF Hex (the usual case), the vector table is lo-
cated between addresses 01E0 and 01FF Hex. If the VIS in-
struction is located between 01FF and 02DF Hex, then the
vector table is located between addresses 02E0 and 02FF
Hex, and so on.
An interrupt is an asychronous event which may occur be-
fore, during, or after an instruction cycle. Any interrupt which
occurs during the execution of an instruction is not acknowl-
edged until the start of the next normally executed instruction
is to be skipped, the skip is performed before the pending in-
terrupt is acknowledged.
At the start of interrupt acknowledgment, the following ac-
tions occur:
1. The GIE bit is automatically reset to zero, preventing any
subsequent maskable interrupt from interrupting the cur-
rent service routine. This feature prevents one maskable
interrupt from interrupting another one being serviced.
Each vector is 15 bits long and points to the beginning of a
specific interrupt service routine somewhere in the 32 kbyte
memory space. Each vector occupies two bytes of the vector
table, with the higher-order byte at the lower address. The
vectors are arranged in order of interrupt priority. The vector
of the maskable interrupt with the lowest rank is located to
0yE0 (higher-order byte) and 0yE1 (lower-order byte). The
next priority interrupt is located at 0yE2 and 0yE3, and so
forth in increasing rank. The Software Trap has the highest
rank and its vector is always located at 0yFE and 0yFF. The
number of interrupts which can become active defines the
size of the table.
2. The address of the instruction about to be executed is
pushed onto the stack.
3. The program counter (PC) is loaded with 00FF Hex,
causing a jump to that program memory location.
The device requires seven instruction cycles to perform the
actions listed above.
If the user wishes to allow nested interrupts, the interrupts
service routine may set the GIE bit to 1 by writing to the PSW
register, and thus allow other maskable interrupts to interrupt
the current service routine. If nested interrupts are allowed,
caution must be exercised. The user must write the program
in such a way as to prevent stack overflow, loss of saved
context information, and other unwanted conditions.
Table 5 shows the types of interrupts, the interrupt arbitration
ranking, and the locations of the corresponding vectors in
the vector table.
The vector table should be filled by the user with the memory
locations of the specific interrupt service routines. For ex-
The interrupt service routine stored at location 00FF Hex
should use the VIS instruction to determine the cause of the
www.national.com
32
gram context (A, B, X, etc.) and executing the RETI instruc-
tion, an interrupt service routine can be terminated by return-
ing to the VIS instruction. In this case, interrupts will be
serviced in turn until no further interrupts are pending and
the default VIS routine is started. After testing the GIE bit to
ensure that execution is not erroneous, the routine should
restore the program context and execute the RETI to return
to the interrupted program.
Interrupts (Continued)
ample, if the Software Trap routine is located at 0310 Hex,
then the vector location 0yFE and -0yFF should contain the
data 03 and 10 Hex, respectively. When a Software Trap in-
terrupt occurs and the VIS instruction is executed, the pro-
gram jumps to the address specified in the vector table.
The interrupt sources in the vector table are listed in order of
rank, from highest to lowest priority. If two or more enabled
and pending interrupts are detected at the same time, the
one with the highest priority is serviced first. Upon return
from the interrupt service routine, the next highest-level
pending interrupt is serviced.
This technique can save up to fifty instruction cycles (t
c), or
more, (50µs at 10 MHz oscillator) of latency for pending in-
terrupts with a penalty of fewer than ten instruction cycles if
no further interrupts are pending.
To ensure reliable operation, the user should always use the
VIS instruction to determine the source of an interrupt. Al-
though it is possible to poll the pending bits to detect the
source of an interrupt, this practice is not recommended. The
use of polling allows the standard arbitration ranking to be al-
tered, but the reliability of the interrupt system is compro-
mised. The polling routine must individually test the enable
and pending bits of each maskable interrupt. If a Software
Trap interrupt should occur, it will be serviced last, even
though it should have the highest priority. Under certain con-
ditions, a Software Trap could be triggered but not serviced,
resulting in an inadvertent “locking out” of all maskable inter-
rupts by the Software Trap pending flag. Problems such as
this can be avoided by using VIS instruction.
If the VIS instruction is executed, but no interrupts are en-
abled and pending, the lowest-priority interrupt vector is
used, and a jump is made to the corresponding address in
the vector table. This is an unusual occurrence, and may be
the result of an error. It can legitimately result from a change
in the enable bits or pending flags prior to the execution of
the VIS instruction, such as executing a single cycle instruc-
tion which clears an enable flag at the same time that the
pending flag is set. It can also result, however, from inadvert-
ent execution of the VIS command outside of the context of
an interrupt.
The default VIS interrupt vector can be useful for applica-
tions in which time critical interrupts can occur during the
servicing of another interrupt. Rather than restoring the pro-
TABLE 5. Interrupt Vector Table
Vector Address (Note *NO
TARGET FOR FNXref NS7955*)
(Hi-Low Byte)
0yFE–0yFF
Arbitration
Source
Description
Ranking
(1) Highest
(2)
Software
INTR Instruction
Reserved
External
0yFC–0yFD
(3)
G0
0yFA–0yFB
(4)
Timer T0
Underflow
T1A/Underflow
T1B
0yF8–0yF9
(5)
Timer T1
0yF6–0yF7
(6)
Timer T1
0yF4–0yF5
(7)
MICROWIRE/PLUS
Reserved
UART
BUSY Low
0yF2–0yF3
(8)
0yF0–0yF1
(9)
Receive
0yEE–0yEF
(10)
(11)
(12)
(13)
(14)
(15)
(16) Lowest
UART
Transmit
T2A/Underflow
T2B
0yEC–0yED
Timer T2 *
Timer T2 *
Timer T3 *
Timer T3 *
Port L/Wakeup
Default VIS
0yEA–0yEB
0yE8–0yE9
T2A/Underflow
T3B
0yE6–0yE7
0yE4–0yE5
Port L Edge
Reserved
0yE2–0yE3
0yE0–0yE1
Note 13: y is a variable which represents the VIS block. VIS and the vector table must be located in the same 256-byte block except if VIS is located at the last ad-
dress of a block. In this case, the table must be in the next block.
*
Reserved on the CS series.
33
www.national.com
Interrupts (Continued)
VIS Execution
When the VIS instruction is executed it activates the arbitra-
tion logic. The arbitration logic generates an even number
between E0 and FE (E0, E2, E4, E6 etc...) depending on
which active interrupt has the highest arbitration ranking at
the time of the 1st cycle of VIS is executed. For example, if
the software trap interrupt is active, FE is generated. If the
external interrupt is active and the software trap interrupt is
not, then FA is generated and so forth. If the only active inter-
rupt is software trap, than E0 is generated. This number re-
places the lower byte of the PC. The upper byte of the PC re-
mains unchanged. The new PC is therefore pointing to the
vector of the active interrupt with the highest arbitration rank-
ing. This vector is read from program memory and placed
into the PC which is now pointed to the 1st instruction of the
service routine of the active interrupt with the highest arbitra-
tion ranking.
Figure 17 illustrates the different steps performed by the VIS
instruction. Figure 18 shows a flowchart for the VIS instruc-
tion.
The non-maskable interrupt pending flag is cleared by the
RPND (Reset Non-Maskable Pending Bit) instruction (under
certain conditions) and upon RESET.
DS012829-43
FIGURE 17. VIS Operation
www.national.com
34
Interrupts (Continued)
DS012829-44
FIGURE 18. VIS Flowchart
35
www.national.com
Interrupts (Continued)
Programming Example: External Interrupt
PSW
CNTRL
RBIT
RBIT
SBIT
SBIT
SBIT
JP
=00EF
=00EE
0,PORTGC
0,PORTGD
IEDG, CNTRL
EXEN, PSW
GIE, PSW
WAIT
; G0 pin configured Hi-Z
; Ext interrupt polarity; falling edge
; Enable the external interrupt
; Set the GIE bit
WAIT:
; Wait for external interrupt
.
.
.
.=0FF
VIS
; The interrupt causes a
; branch to address 0FF
; The VIS causes a branch to
;interrupt vector table
.
.
.
.=01FA
.ADDRW SERVICE
; Vector table (within 256 byte
; of VIS inst.) containing the ext
; interrupt service routine
.
.
INT_EXIT:
SERVICE:
RETI
.
.
RBIT
EXPND, PSW
; Interrupt Service Routine
; Reset ext interrupt pend. bit
.
.
.
JP
INT_EXIT
; Return, set the GIE bit
www.national.com
36
flag; upon return to the first Software Trap routine, the
STPND flag will have the wrong state. This will allow
maskable interrupts to be acknowledged during the servicing
of the first Software Trap. To avoid problems such as this, the
user program should contain the Software Trap routine to
perform a recovery procedure rather than a return to normal
execution.
Interrupts (Continued)
NON-MASKABLE INTERRUPT
Pending Flag
There is a pending flag bit associated with the non-maskable
interrupt, called STPND. This pending flag is not memory-
mapped and cannot be accessed directly by the software.
Under normal conditions, the STPND flag is reset by a
RPND instruction in the Software Trap service routine. If a
programming error or hardware condition (brownout, power
supply glitch, etc.) sets the STPND flag without providing a
way for it to be cleared, all other interrupts will be locked out.
To alleviate this condition, the user can use extra RPND in-
structions in the main program and in the WATCHDOG ser-
vice routine (if present). There is no harm in executing extra
RPND instructions in these parts of the program.
The pending flag is reset to zero when a device Reset oc-
curs. When the non-maskable interrupt occurs, the associ-
ated pending bit is set to 1. The interrupt service routine
should contain an RPND instruction to reset the pending flag
to zero. The RPND instruction always resets the STPND
flag.
Software Trap
The Software Trap is a special kind of non-maskable inter-
rupt which occurs when the INTR instruction (used to ac-
knowledge interrupts) is fetched from program memory and
placed in the instruction register. This can happen in a vari-
ety of ways, usually because of an error condition. Some ex-
amples of causes are listed below.
PORT L INTERRUPTS
Port L provides the user with an additional eight fully select-
able, edge sensitive interrupts which are all vectored into the
same service subroutine.
The interrupt from Port L shares logic with the wake up cir-
cuitry. The register WKEN allows interrupts from Port L to be
individually enabled or disabled. The register WKEDG speci-
fies the trigger condition to be either a positive or a negative
edge. Finally, the register WKPND latches in the pending
trigger conditions.
If the program counter incorrectly points to a memory loca-
tion beyond the available program memory space, the non-
existent or unused memory location returns zeroes which is
interpreted as the INTR instruction.
If the stack is popped beyond the allowed limit (address 06F
Hex), a 7FFF will be loaded into the PC, if this last location in
program memory is unprogrammed or unavailable, a Soft-
ware Trap will be triggered.
The GIE (Global Interrupt Enable) bit enables the interrupt
function.
A control flag, LPEN, functions as a global interrupt enable
for Port L interrupts. Setting the LPEN flag will enable inter-
rupts and vice versa. A separate global pending flag is not
needed since the register WKPND is adequate.
A Software Trap can be triggered by a temporary hardware
condition such as a brownout or power supply glitch.
The Software Trap has the highest priority of all interrupts.
When a Software Trap occurs, the STPND bit is set. The GIE
bit is not affected and the pending bit (not accessible by the
user) is used to inhibit other interrupts and to direct the pro-
gram to the ST service routine with the VIS instruction. Noth-
ing can interrupt a Software Trap service routine except for
another Software Trap. The STPND can be reset only by the
RPND instruction or a chip Reset.
Since Port L is also used for waking the device out of the
HALT or IDLE modes, the user can elect to exit the HALT or
IDLE modes either with or without the interrupt enabled. If he
elects to disable the interrupt, then the device will restart ex-
ecution from the instruction immediately following the in-
struction that placed the microcontroller in the HALT or IDLE
modes. In the other case, the device will first execute the in-
terrupt service routine and then revert to normal operation.
(See HALT MODE for clock option wakeup information.)
The Software Trap indicates an unusual or unknown error
condition. Generally, returning to normal execution at the
point where the Software Trap occurred cannot be done re-
liably. Therefore, the Software Trap service routine should
reinitialize the stack pointer and perform a recovery proce-
dure that restarts the software at some known point, similar
to a device Reset, but not necessarily performing all the
same functions as a device Reset. The routine must also ex-
ecute the RPND instruction to reset the STPND flag. Other-
wise, all other interrupts will be locked out. To the extent pos-
sible, the interrupt routine should record or indicate the
context of the device so that the cause of the Software Trap
can be determined.
INTERRUPT SUMMARY
The device uses the following types of interrupts, listed be-
low in order of priority:
1. The Software Trap non-maskable interrupt, triggered by
the INTR (00 opcode) instruction. The Software Trap is
acknowledged immediately. This interrupt service rou-
tine can be interrupted only by another Software Trap.
The Software Trap should end with two RPND instruc-
tions followed by a restart procedure.
2. Maskable interrupts, triggered by an on-chip peripheral
block or an external device connected to the device. Un-
der ordinary conditions, a maskable interrupt will not in-
If the user wishes to return to normal execution from the
point at which the Software Trap was triggered, the user
must first execute RPND, followed by RETSK rather than
RETI or RET. This is because the return address stored on
the stack is the address of the INTR instruction that triggered
the interrupt. The program must skip that instruction in order
to proceed with the next one. Otherwise, an infinite loop of
Software Traps and returns will occur.
terrupt any other interrupt routine in progress.
maskable interrupt routine in progress can be inter-
rupted by the non-maskable interrupt request.
maskable interrupt routine should end with an RETI in-
struction or, prior to restoring context, should return to
execute the VIS instruction. This is particularly useful
when exiting long interrupt service routiness if the time
between interrupts is short. In this case the RETI instruc-
tion would only be executed when the default VIS rou-
tine is reached.
A
A
Programming a return to normal execution requires careful
consideration. If the Software Trap routine is interrupted by
another Software Trap, the RPND instruction in the service
routine for the second Software Trap will reset the STPND
37
www.national.com
occur after coming out of reset, if the instruction cycle clock
frequency has not reached a minimum specified value, in-
cluding the case where the oscillator fails to start.
WATCHDOG
The device contains a WATCHDOG and clock monitor. The
WATCHDOG is designed to detect the user program getting
stuck in infinite loops resulting in loss of program control or
“runaway” programs. The Clock Monitor is used to detect the
absence of a clock or a very slow clock below a specified
rate on the CKI pin.
The WDSVR register can be written to only once after reset
and the key data (bits 5 through 1 of the WDSVR Register)
must match to be a valid write. This write to the WDSVR reg-
ister involves two irrevocable choices: (i) the selection of the
WATCHDOG service window (ii) enabling or disabling of the
Clock Monitor. Hence, the first write to WDSVR Register in-
volves selecting or deselecting the Clock Monitor, select the
WATCHDOG service window and match the WATCHDOG
key data. Subsequent writes to the WDSVR register will
compare the value being written by the user to the WATCH-
DOG service window value and the key data (bits 7 through
1) in the WDSVR Register. Table 8 shows the sequence of
events that can occur.
The WATCHDOG consists of two independent logic blocks:
WD UPPER and WD LOWER. WD UPPER establishes the
upper limit on the service window and WD LOWER defines
the lower limit of the service window.
Servicing the WATCHDOG consists of writing a specific
value to a WATCHDOG Service Register named WDSVR
which is memory mapped in the RAM. This value is com-
posed of three fields, consisting of a 2-bit Window Select, a
5-bit Key Data field, and the 1-bit Clock Monitor Select field.
Table 6 shows the WDSVR register.
The user must service the WATCHDOG at least once before
the upper limit of the service window expires. The WATCH-
DOG may not be serviced more than once in every lower
limit of the service window. The user may service the
WATCHDOG as many times as wished in the time period be-
tween the lower and upper limits of the service window. The
first write to the WDSVR Register is also counted as a
WATCHDOG service.
TABLE 6. WATCHDOG Service Register (WDSVR)
Window
Select
Key Data
Clock
Monitor
X
X
6
0
5
1
4
1
3
0
2
0
1
Y
0
The WATCHDOG has an output pin associated with it. This
is the WDOUT pin, on pin 1 of the port G. WDOUT is active
low. The WDOUT pin is in the high impedance state in the in-
active state. Upon triggering the WATCHDOG, the logic will
pull the WDOUT (G1) pin low for an additional 16 tc–32 tc
cycles after the signal level on WDOUT pin goes below the
lower Schmitt trigger threshold. After this delay, the device
will stop forcing the WDOUT output low.
7
The lower limit of the service window is fixed at 2048 instruc-
tion cycles. Bits 7 and 6 of the WDSVR register allow the
user to pick an upper limit of the service window.
Table 7 shows the four possible combinations of lower and
upper limits for the WATCHDOG service window. This flex-
ibility in choosing the WATCHDOG service window prevents
any undue burden on the user software.
The WATCHDOG service window will restart when the WD-
OUT pin goes high. It is recommended that the user tie the
WDOUT pin back to VCC through a resistor in order to pull
WDOUT high.
Bits 5, 4, 3, 2 and 1 of the WDSVR register represent the
5-bit Key Data field. The key data is fixed at 01100. Bit 0 of
the WDSVR Register is the Clock Monitor Select bit.
A WATCHDOG service while the WDOUT signal is active will
be ignored. The state of the WDOUT pin is not guaranteed
on reset, but if it powers up low then the WATCHDOG will
time out and WDOUT will enter high impedance state.
TABLE 7. WATCHDOG Service Window Select
WDSVR WDSVR
Clock
Service Window
(Lower-Upper Limits)
2048–8k tC Cycles
Bit 7
Bit 6
Monitor
The Clock Monitor forces the G1 pin low upon detecting a
clock frequency error. The Clock Monitor error will continue
until the clock frequency has reached the minimum specified
value, after which the G1 output will enter the high imped-
ance TRI-STATE mode following 16 tc–32 tc clock cycles.
The Clock Monitor generates a continual Clock Monitor error
if the oscillator fails to start, or fails to reach the minimum
specified frequency. The specification for the Clock Monitor
is as follows:
0
0
1
1
x
x
0
1
0
1
x
x
x
x
x
x
0
1
2048–16k tC Cycles
2048–32k tC Cycles
2048–64k tC Cycles
Clock Monitor Disabled
Clock Monitor Enabled
>
1/tc 10 kHz—No clock rejection.
Clock Monitor
<
1/tc 10 Hz—Guaranteed clock rejection.
The Clock Monitor aboard the device can be selected or de-
selected under program control. The Clock Monitor is guar-
anteed not to reject the clock if the instruction cycle clock (1/
tc) is greater or equal to 10 kHz. This equates to a clock input
rate on CKI of greater or equal to 100 kHz.
WATCHDOG AND CLOCK MONITOR SUMMARY
The following salient points regarding the WATCHDOG and
CLOCK MONITOR should be noted:
•
Both the WATCHDOG and CLOCK MONITOR detector
circuits are inhibited during RESET.
WATCHDOG Operation
•
Following RESET, the WATCHDOG and CLOCK MONI-
TOR are both enabled, with the WATCHDOG having he
maximum service window selected.
The WATCHDOG and Clock Monitor are disabled during re-
set. The device comes out of reset with the WATCHDOG
armed, the WATCHDOG Window Select bits (bits 6, 7 of the
WDSVR Register) set, and the Clock Monitor bit (bit 0 of the
WDSVR Register) enabled. Thus, a Clock Monitor error will
•
The WATCHDOG service window and CLOCK MONI-
TOR enable/disable option can only be changed once,
during the initial WATCHDOG service following RESET.
www.national.com
38
The subroutine stack grows down for each call (jump to sub-
routine), interrupt, or PUSH, and grows up for each return or
POP. The stack pointer is initialized to RAM location 06F Hex
during reset. Consequently, if there are more returns than
calls, the stack pointer will point to addresses 070 and 071
Hex (which are undefined RAM). Undefined RAM from ad-
dresses 070 to 07F (Segment 0), and all other segments
(i.e., Segments 4 … etc.) is read as all 1’s, which in turn will
cause the program to return to address 7FFF Hex. This is an
undefined ROM location and the instruction fetched (all 0’s)
from this location will generate a software interrupt signaling
an illegal condition.
WATCHDOG Operation (Continued)
•
•
•
The initial WATCHDOG service must match the key data
value in the WATCHDOG Service register WDSVR in or-
der to avoid a WATCHDOG error.
Subsequent WATCHDOG services must match all three
data fields in WDSVR in order to avoid WATCHDOG er-
rors.
The correct key data value cannot be read from the
WATCHDOG Service register WDSVR. Any attempt to
read this key data value of 01100 from WDSVR will read
as key data value of all 0’s.
Thus, the chip can detect the following illegal conditions:
1. Executing from undefined ROM
•
•
The WATCHDOG detector circuit is inhibited during both
the HALT and IDLE modes.
2. Over “POP”ing the stack by having more returns than
calls.
The CLOCK MONITOR detector circuit is active during
both the HALT and IDLE modes. Consequently, the de-
vice inadvertently entering the HALT mode will be de-
tected as a CLOCK MONITOR error (provided that the
CLOCK MONITOR enable option has been selected by
the program).
When the software interrupt occurs, the user can re-initialize
the stack pointer and do a recovery procedure before restart-
ing (this recovery program is probably similar to that follow-
ing reset, but might not contain the same program initializa-
tion procedures). The recovery program should reset the
software interrupt pending bit using the RPND instruction.
•
•
With the single-pin R/C oscillator mask option selected
and the CLKDLY bit reset, the WATCHDOG service win-
dow will resume following HALT mode from where it left
off before entering the HALT mode.
MICROWIRE/PLUS
With the crystal oscillator mask option selected, or with
the single-pin R/C oscillator mask option selected and the
CLKDLY bit set, the WATCHDOG service window will be
set to its selected value from WDSVR following HALT.
Consequently, the WATCHDOG should not be serviced
for at least 2048 instruction cycles following HALT, but
must be serviced within the selected window to avoid a
WATCHDOG error.
MICROWIRE/PLUS is a serial synchronous communications
interface. The MICROWIRE/PLUS capability enables the de-
vice to interface with any of National Semiconductor’s MI-
CROWIRE peripherals (i.e. A/D converters, display drivers,
E2PROMs etc.) and with other microcontrollers which sup-
port the MICROWIRE interface. It consists of an 8-bit serial
shift register (SIO) with serial data input (SI), serial data out-
put (SO) and serial shift clock (SK). Figure 19 shows a block
diagram of the MICROWIRE/PLUS logic.
•
•
The IDLE timer T0 is not initialized with RESET.
The user can sync in to the IDLE counter cycle with an
IDLE counter (T0) interrupt or by monitoring the T0PND
flag. The T0PND flag is set whenever the thirteenth bit of
the IDLE counter toggles (every 4096 instruction cycles).
The user is responsible for resetting the T0PND flag.
•
•
A hardware WATCHDOG service occurs just as the de-
vice exits the IDLE mode. Consequently, the WATCH-
DOG should not be serviced for at least 2048 instruction
cycles following IDLE, but must be serviced within the se-
lected window to avoid a WATCHDOG error.
Following RESET, the initial WATCHDOG service (where
the service window and the CLOCK MONITOR enable/
disable must be selected) may be programmed any-
where within the maximum service window (65,536 in-
struction cycles) initialized by RESET. Note that this initial
WATCHDOG service may be programmed within the ini-
tial 2048 instruction cycles without causing a WATCH-
DOG error.
DS012829-19
FIGURE 19. MICROWIRE/PLUS Block Diagram
The shift clock can be selected from either an internal source
or an external source. Operating the MICROWIRE/PLUS ar-
rangement with the internal clock source is called the Master
mode of operation. Similarly, operating the MICROWIRE/
PLUS arrangement with an external shift clock is called the
Slave mode of operation.
Detection of Illegal Conditions
The device can detect various illegal conditions resulting
from coding errors, transient noise, power supply voltage
drops, runaway programs, etc.
The CNTRL register is used to configure and control the
MICROWIRE/PLUS mode. To use the MICROWIRE/PLUS,
the MSEL bit in the CNTRL register is set to one. In the mas-
ter mode, the SK clock rate is selected by the two bits, SL0
and SL1, in the CNTRL register. Table 9 details the different
clock rates that may be selected.
Reading of undefined ROM gets zeros. The opcode for soft-
ware interrupt is zero. If the program fetches instructions
from undefined ROM, this will force a software interrupt, thus
signaling that an illegal condition has occurred.
39
www.national.com
MICROWIRE/PLUS (Continued)
TABLE 8. WATCHDOG Service Actions
Key
Window
Clock
Monitor
Match
Action
Data
Data
Match
Match
Valid Service: Restart Service Window
Error: Generate WATCHDOG Output
Error: Generate WATCHDOG Output
Error: Generate WATCHDOG Output
Don’t Care
Mismatch
Don’t Care
Mismatch
Don’t Care
Don’t Care
Don’t Care
Don’t Care
Mismatch
onto the G Port. The SK pin must be selected as an input
and the SO pin is selected as an output pin by setting and re-
setting the appropriate bits in the Port G configuration regis-
ter. Table 10 summarizes the settings required to enter the
Slave mode of operation.
TABLE 9. MICROWIRE/PLUS
Master Mode Clock Select
SL1
0
SL0
SK
0
1
x
2 x tc
4 x tc
8 x tc
The user must set the BUSY flag immediately upon entering
the Slave mode. This will ensure that all data bits sent by the
Master will be shifted properly. After eight clock pulses the
BUSY flag will be cleared and the sequence may be re-
peated.
0
1
Where tc is the instruction cycle clock
MICROWIRE/PLUS OPERATION
Setting the BUSY bit in the PSW register causes the
MICROWIRE/PLUS to start shifting the data. It gets reset
when eight data bits have been shifted. The user may reset
the BUSY bit by software to allow less than 8 bits to shift. If
enabled, an interrupt is generated when eight data bits have
been shifted. The device may enter the MICROWIRE/PLUS
mode either as a Master or as a Slave. Figure 20 shows how
two microcontroller devices and several peripherals may be
interconnected using the MICROWIRE/PLUS arrangements.
Alternate SK Phase Operation
The device allows either the normal SK clock or an alternate
phase SK clock to shift data in and out of the SIO register. In
both the modes the SK is normally low. In the normal mode
data is shifted in on the rising edge of the SK clock and the
data is shifted out on the falling edge of the SK clock. The
SIO register is shifted on each falling edge of the SK clock.
In the alternate SK phase operation, data is shifted in on the
falling edge of the SK clock and shifted out on the rising edge
of the SK clock.
Warning:
A control flag, SKSEL, allows either the normal SK clock or
the alternate SK clock to be selected. Resetting SKSEL
causes the MICROWIRE/PLUS logic to be clocked from the
normal SK signal. Setting the SKSEL flag selects the alter-
nate SK clock. The SKSEL is mapped into the G6 configura-
tion bit. The SKSEL flag will power up in the reset condition,
selecting the normal SK signal.
The SIO register should only be loaded when the SK clock is
low. Loading the SIO register while the SK clock is high will
result in undefined data in the SIO register. SK clock is nor-
mally low when not shifting.
Setting the BUSY flag when the input SK clock is high in the
MICROWIRE/PLUS slave mode may cause the current SK
clock for the SIO shift register to be narrow. For safety, the
BUSY flag should only be set when the input SK clock is low.
TABLE 10. MICROWIRE/PLUS Mode Settings
This table assumes that the control flag MSEL is set.
MICROWIRE/PLUS Master Mode Operation
In the MICROWIRE/PLUS Master mode of operation the
shift clock (SK) is generated internally by the device. The MI-
CROWIRE Master always initiates all data exchanges. The
MSEL bit in the CNTRL register must be set to enable the
SO and SK functions onto the G Port. The SO and SK pins
must also be selected as outputs by setting appropriate bits
in the Port G configuration register. Table 10 summarizes the
bit settings required for Master mode of operation.
G4 (SO)
Config. Bit
1
G5 (SK)
Config. Bit
1
G4
Fun.
SO
G5
Fun.
Int.
Operation
MICROWIRE/PLUS
Master
SK
0
1
0
1
0
0
TRI-
STATE
SO
Int.
MICROWIRE/PLUS
Master
SK
Ext. MICROWIRE/PLUS
SK Slave
Ext. MICROWIRE/PLUS
SK Slave
MICROWIRE/PLUS Slave Mode Operation
TRI-
In the MICROWIRE/PLUS Slave mode of operation the SK
clock is generated by an external source. Setting the MSEL
bit in the CNTRL register enables the SO and SK functions
STATE
www.national.com
40
MICROWIRE/PLUS (Continued)
DS012829-20
FIGURE 20. MICROWIRE/PLUS Application
Memory Map
All RAM, ports and registers (except A and PC) are mapped into data memory address space.
Address
Contents
Address
Contents
S/ADD REG
S/ADD REG
0000 to 006F
0070 to 007F
xxBC
UART Interrupt and Clock Source
Register (Reg:ENUI)
On-Chip RAM bytes (112 bytes)
Unused RAM Address Space (Reads As
All Ones)
xxBD
xxBE
UART Baud Register (Reg:BAUD)
UART Prescale Select Register
(Reg:PSR)
xx80 to xx93
Unused RAM Address Space (Reads
Undefined Data)
xxBF
xxC0
xxC1
xxC2
Reserved for UART
Timer T2 Lower Byte
Timer T2 Upper Byte
xx94
Port F data register, PORTFD
xx95
Port F configuration register, PORTFC
Port F input pins (read only), PORTFP
xx96
Timer T2 Autoload Register T2RA Lower
Byte
xx97 to xxAF
Unused address space (Reads
Undefined Data)
xxC3
xxC4
xxC5
Timer T2 Autoload Register T2RA Upper
Byte
xxB0
xxB1
xxB2
Timer T3 Lower Byte
Timer T3 Upper Byte
Timer T2 Autoload Register T2RB Lower
Byte
Timer T3 Autoload Register T3RA Lower
Byte
Timer T2 Autoload Register T2RB Upper
Byte
xxB3
xxB4
xxB5
Timer T3 Autoload Register T3RA Upper
Byte
xxC6
xxC7
Timer T2 Control Register
Timer T3 Autoload Register T3RB Lower
Byte
WATCHDOG Service Register
(Reg:WDSVR)
Timer T3 Autoload Register T3RB Upper
Byte
xxC8
MIWU Edge Select Register
(Reg:WKEDG)
xxB6
xxB7
Timer T3 Control Register
xxC9
xxCA
MIWU Enable Register (Reg:WKEN)
MIWU Pending Register (Reg:WKPND)
Comparator Select Register
(Reg:CMPSL)
xxCB to xxCF Reserved
xxB8
xxB9
xxBA
UART Transmit Buffer (Reg:TBUF)
UART Receive Buffer (Reg:RBUF)
xxD0
xxD1
xxD2
xxD3
xxD4
xxD5
Port L Data Register
Port L Configuration Register
Port L Input Pins (Read Only)
Reserved for Port L
UART Control and Status Register
(Reg:ENU)
xxBB
UART Receive Control and Status
Register (Reg:ENUR)
Port G Data Register
Port G Configuration Register
41
www.national.com
Memory Map (Continued)
Address
S/ADD REG
xxEC
Contents
Address
Contents
Timer T1 Autoload Register T1RA Lower
Byte
S/ADD REG
xxD6
xxD7
Port G Input Pins (Read Only)
xxED
Timer T1 Autoload Register T1RA Upper
Byte
Port I Input Pins (Read Only) (Actually
reads Port F input pins)
xxEE
CNTRL Control Register
PSW Register
xxD8
xxD9
xxDA
xxDB
xxDC
Port C Data Register
Port C Configuration Register
Port C Input Pins (Read Only)
Reserved for Port C
Port D
xxEF
xxF0 to FB
xxFC
On-Chip RAM Mapped as Registers
X Register
xxFD
SP Register
xxFE
B Register
xxDD to xxDF Reserved for Port D
xxFF
S Register
xxE0 to xxE5
xxE6
Reserved for EE Control Registers
0100–017F
0200–027F
On-Chip 128 RAM Bytes
Timer T1 Autoload Register T1RB Lower
Byte
On-Chip 128 RAM Bytes (Reads as
undefined data on COP8SGE)
xxE7
Timer T1 Autoload Register T1RB Upper
Byte
0300–037F
On-Chip 128 RAM Bytes (Reads as
undefined data on COP8SGE)
xxE8
xxE9
xxEA
xxEB
ICNTRL Register
Note: Reading memory locations 0070H–007FH (Segment 0) will return all
ones. Reading unused memory locations 0080H–00AFH (Segment 0)
will return undefined data. Reading memory locations from other Seg-
ments (i.e., Segment 2, Segment 3, … etc.) will return undefined data.
MICROWIRE/PLUS Shift Register
Timer T1 Lower Byte
Timer T1 Upper Byte
Addressing Modes
There are ten addressing modes, six for operand addressing
TRANSFER OF CONTROL ADDRESSING MODES
Relative
and four for transfer of control.
OPERAND ADDRESSING MODES
Register Indirect
This mode is used for the JP instruction, with the instruction
field being added to the program counter to get the new pro-
gram location. JP has a range from −31 to +32 to allow a
1-byte relative jump (JP + 1 is implemented by a NOP in-
struction). There are no “pages” when using JP, since all 15
bits of PC are used.
This is the “normal” addressing mode. The operand is the
data memory addressed by the B pointer or X pointer.
Register Indirect (with auto post increment or
decrement of pointer)
This addressing mode is used with the LD and X instruc-
tions. The operand is the data memory addressed by the B
pointer or X pointer. This is a register indirect mode that au-
tomatically post increments or decrements the B or X regis-
ter after executing the instruction.
Absolute
This mode is used with the JMP and JSR instructions, with
the instruction field of 12 bits replacing the lower 12 bits of
the program counter (PC). This allows jumping to any loca-
tion in the current 4k program memory segment.
Direct
Absolute Long
The instruction contains an 8-bit address field that directly
points to the data memory for the operand.
This mode is used with the JMPL and JSRL instructions, with
the instruction field of 15 bits replacing the entire 15 bits of
the program counter (PC). This allows jumping to any loca-
tion up to 32k in the program memory space.
Immediate
The instruction contains an 8-bit immediate field as the oper-
and.
Short Immediate
Indirect
This addressing mode is used with the Load B Immediate in-
struction. The instruction contains a 4-bit immediate field as
the operand.
This mode is used with the JID instruction. The contents of
the accumulator are used as a partial address (lower 8 bits of
PC) for accessing a location in the program memory. The
contents of this program memory location serve as a partial
address (lower 8 bits of PC) for the jump to the next instruc-
tion.
Note: The VIS is a special case of the Indirect Transfer of Control addressing
mode, where the double byte vector associated with the interrupt is
transferred from adjacent addresses in the program memory into the
program counter (PC) in order to jump to the associated interrupt ser-
vice routine.
Indirect
This addressing mode is used with the LAID instruction. The
contents of the accumulator are used as a partial address
(lower 8 bits of PC) for accessing a data operand from the
program memory.
www.national.com
42
Instruction Set
Register and Symbol Definition
Registers
A
8-Bit Accumulator Register
8-Bit Address Register
B
X
8-Bit Address Register
S
8-Bit Segment Register
SP
PC
PU
PL
C
8-Bit Stack Pointer Register
15-Bit Program Counter Register
Upper 7 Bits of PC
Lower 8 Bits of PC
1 Bit of PSW Register for Carry
1 Bit of PSW Register for Half Carry
HC
GIE
1 Bit of PSW Register for Global Interrupt
Enable
VU
VL
Interrupt Vector Upper Byte
Interrupt Vector Lower Byte
Symbols
[B]
Memory Indirectly Addressed by B Register
Memory Indirectly Addressed by X Register
Direct Addressed Memory
[X]
MD
Mem
Meml
Direct Addressed Memory or [B]
Direct Addressed Memory or [B] or
Immediate Data
Imm
Reg
8-Bit Immediate Data
Register Memory: Addresses F0 to FF
(Includes B, X and SP)
Bit
←
↔
Bit Number (0 to 7)
Loaded with
Exchanged with
43
www.national.com
Instruction Set (Continued)
INSTRUCTION SET
←
←
ADD
ADC
A,Meml
A,Meml
ADD
A
A
A + Meml
A + Meml + C, C Carry
←
ADD with Carry
←
HC Half Carry
← ←
A − MemI + C, C Carry
SUBC
A,Meml
Subtract with Carry
A
←
HC Half Carry
←
AND
ANDSZ
OR
A,Meml
A,Imm
A,Meml
A,Meml
MD,Imm
A,Meml
A,Meml
A,Meml
#
Logical AND
A
A and Meml
Logical AND Immed., Skip if Zero
Logical OR
Skip next if (A and Imm) = 0
←
←
A
A
A or Meml
XOR
IFEQ
IFEQ
IFNE
IFGT
IFBNE
DRSZ
SBIT
RBIT
IFBIT
RPND
X
Logical EXclusive OR
IF EQual
A xor Meml
Compare MD and Imm, Do next if MD = Imm
Compare A and Meml, Do next if A = Meml
IF EQual
≠
Compare A and Meml, Do next if A Meml
IF Not Equal
>
IF Greater Than
Compare A and Meml, Do next if A Meml
≠
If B Not Equal
Do next if lower 4 bits of B Imm
←
Reg
Decrement Reg., Skip if Zero
Set BIT
Reg Reg − 1, Skip if Reg = 0
#
#
#
,Mem
,Mem
,Mem
1 to bit, Mem (bit = 0 to 7 immediate)
0 to bit, Mem
Reset BIT
IF BIT
If bit in A or Mem is true do next instruction
Reset Software Interrupt Pending Flag
Reset PeNDing Flag
EXchange A with Memory
EXchange A with Memory [X]
LoaD A with Memory
LoaD A with Memory [X]
LoaD B with Immed.
LoaD Memory Immed
LoaD Register Memory Immed.
EXchange A with Memory [B]
EXchange A with Memory [X]
LoaD A with Memory [B]
LoaD A with Memory [X]
LoaD Memory [B] Immed.
CLeaR A
↔
↔
←
←
←
A,Mem
A,[X]
A
A
A
A
B
Mem
[X]
X
LD
A,Meml
A,[X]
Meml
[X]
LD
LD
B,Imm
Imm
←
Mem Imm
LD
Mem,Imm
Reg,Imm
←
Reg Imm
LD
↔
↔
←
←
±
±
±
±
X
A, [B
A, [X
]
]
A
A
A
A
[B], (B
[X], (X
B
X
B
1)
1)
1)
←
X
←
←
±
±
LD
A, [B ]
[B], (B
←
±
±
LD
A, [X ]
[X], (X X 1)
←
←
±
±
LD
[B ],Imm
[B] Imm, (B B 1)
←
←
←
←
←
→
CLR
INC
A
A
A
A
A
A
A
A
C
C
0
INCrement A
A + 1
DEC
LAID
DCOR
RRC
RLC
SWAP
SC
DECrement A
A − 1
Load A InDirect from ROM
Decimal CORrect A
Rotate A Right thru C
Rotate A Left thru C
SWAP nibbles of A
Set C
ROM (PU,A)
A
A
A
A
BCD correction of A (follows ADC, SUBC)
→
←
→
←
→
←
A7
A7
…
…
A0
A0
C
C
←
↔
A7…A4 A3…A0
←
←
←
←
C
C
1, HC
0, HC
1
0
RC
Reset C
IFC
IF C
IF C is true, do next instruction
IFNC
POP
PUSH
VIS
IF Not C
If C is not true, do next instruction
← ←
SP SP + 1, A [SP]
A
A
POP the stack into A
PUSH A onto the stack
Vector to Interrupt Service Routine
Jump absolute Long
Jump absolute
←
←
[SP] A, SP SP − 1
←
←
PU [VU], PL [VL]
←
PC ii (ii = 15 bits, 0 to 32k)
JMPL
JMP
JP
Addr.
Addr.
Disp.
←
PC9…0 i (i = 12 bits)
←
PC PC + r (r is −31 to +32, except 1)
Jump relative short
www.national.com
44
Instruction Set (Continued)
INSTRUCTION SET (Continued)
← ← ←
[SP] PL, [SP−1] PU,SP−2, PC ii
JSRL
JSR
Addr.
Addr
Jump SubRoutine Long
Jump SubRoutine
Jump InDirect
←
←
←
[SP] PL, [SP−1] PU,SP−2, PC9…0
i
←
PL ROM (PU,A)
JID
← ←
SP + 2, PL [SP], PU [SP−1]
RET
RETurn from subroutine
RETurn and SKip
←
←
RETSK
SP + 2, PL [SP],PU [SP−1],
skip next instruction
←
←
←
RETI
INTR
NOP
RETurn from Interrupt
Generate an Interrupt
No OPeration
SP + 2, PL [SP],PU [SP−1],GIE
1
←
←
←
[SP] PL, [SP−1] PU, SP−2, PC 0FF
←
PC PC + 1
45
www.national.com
Instructions Using A & C
Instruction Execution Time
CLRA
INCA
DECA
LAID
1/1
1/1
1/1
1/3
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/3
1/3
2/2
Most instructions are single byte (with immediate addressing
mode instructions taking two bytes).
Most single byte instructions take one cycle time to execute.
Skipped instructions require x number of cycles to be
skipped, where x equals the number of bytes in the skipped
instruction opcode.
DCOR
RRCA
RLCA
SWAPA
SC
Bytes and Cycles per Instruction
The following table shows the number of bytes and cycles for
each instruction in the format of byte/cycle.
RC
Arithmetic and Logic Instructions
IFC
[B]
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Direct
3/4
Immed.
2/2
IFNC
ADD
ADC
SUBC
AND
OR
PUSHA
POPA
ANDSZ
3/4
2/2
3/4
2/2
3/4
2/2
3/4
2/2
Transfer of Control Instructions
XOR
IFEQ
IFNE
IFGT
IFBNE
DRSZ
SBIT
RBIT
IFBIT
3/4
2/2
JMPL
JMP
JP
3/4
2/3
1/3
3/5
2/5
1/3
1/5
1/5
1/5
1/5
1/7
1/1
3/4
2/2
3/4
2/2
3/4
2/2
JSRL
JSR
1/3
3/4
3/4
3/4
JID
1/1
1/1
1/1
VIS
RET
RETSK
RETI
INTR
NOP
RPND
1/1
Memory Transfer Instructions
Register
Indirect
Direct
Immed.
Register Indirect
Auto Incr. & Decr.
[B]
[X]
1/3
1/3
[B+, B−]
1/2
[X+, X−]
1/3
X A, (Note 14)
LD A, (Note 14)
LD B, Imm
1/1
1/1
2/3
2/3
2/2
1/1
2/2
1/2
1/3
<
(IF B 16)
>
(IF B 15)
LD B, Imm
LD Mem, Imm
LD Reg, Imm
IFEQ MD, Imm
2/2
3/3
2/3
3/3
2/2
>
Memory location addressed by B or X or directly.
Note 14:
=
www.national.com
46
Instruction Execution Time (Continued)
N i b b l e L o w e r
47
www.national.com
•
•
COP8–EVAL-ICUxx: Very Low cost evaluation and de-
sign test board for COP8ACC and COP8SGx Families,
from ICU. Real-time environment with add-on A/D, D/A,
and EEPROM. Includes software routines and reference
designs.
Mask Options
The mask programmable options are shown below. The op-
tions are programmed at the same time as the ROM pattern
submission.
OPTION 1: CLOCK CONFIGURATION
= 1 Crystal Oscillator (CKI/10)
G7 (CKO) is clock generator output to crystal/
resonator with CKI being the clock input
= 2 Single-pin RC controlled oscillator (CKI/10)
G7 is available as a HALT restart and/or
general purpose input
Manuals, Applications Notes, Literature: Available free
from our web site at: www.national.com/cop8.
COP8 Integrated Software/Hardware Design Develop-
ment Kits
•
COP8-EPU: Very Low cost Evaluation & Programming
Unit. Windows based development and hardware-
simulation tool for COPSx/xG families, with COP8 device
programmer and samples. Includes COP8-NSDEV,
Driveway COP8 Demo, MetaLink Debugger, cables and
power supply.
OPTION 2: HALT
= 1 Enable HALT mode
•
COP8-DM: Moderate cost Debug Module from MetaLink.
A Windows based, real-time in-circuit emulation tool with
COP8 device programmer. Includes COP8-NSDEV,
DriveWay COP8 Demo, MetaLink Debugger, power sup-
ply, emulation cables and adapters.
= 2 Disable HALT mode
OPTION 3: BONDING OPTIONS
= 1 44-Pin PLCC
= 2 40-Pin DIP
= 3 N/A
COP8 Development Languages and Environments
= 4 28-DIP
•
COP8-NSASM: Free COP8 Assembler v5 for Win32.
Macro assembler, linker, and librarian for COP8 software
development. Supports all COP8 devices. (DOS/Win16
v4.10.2 available with limited support). (Compatible with
WCOP8 IDE, COP8C, and DriveWay COP8).
= 5 28-Pin SO
Some device can be driven by a clock input on the CKI input
pin which can be between DC and 10 MHz. The CKO output
clock is on pin G7 (if clock option=1 has been selected). The
CKI input frequency is divided down by 10 to produce the in-
struction cycle clock (1/tc).
•
•
COP8-NSDEV: Very low cost Software Development
Package for Windows. An integrated development envi-
ronment for COP8, including WCOP8 IDE, COP8-
NSASM, COP8-MLSIM.
Not all packages are available for all devices, please check
order information.
COP8C: Moderately priced C Cross-Compiler and Code
Development System from Byte Craft (no code limit). In-
cludes BCLIDE (Byte Craft Limited Integrated Develop-
ment Environment) for Win32, editor, optimizing C Cross-
Compiler, macro cross assembler, BC-Linker, and
MetaLink tools support. (DOS/SUN versions available;
Compiler is installable under WCOP8 IDE; Compatible
with DriveWay COP8).
Development Support
OVERVIEW
National is engaged with an international community of inde-
pendent 3rd party vendors who provide hardware and soft-
ware development tool support. Through National’s interac-
tion and guidance, these tools cooperate to form a choice of
tools that fits each developer’s needs.
•
•
EWCOP8-KS: Very Low cost ANSI C-Compiler and Em-
bedded Workbench from IAR (Kickstart version:
COP8Sx/Fx only with 2k code limit; No FP). A fully inte-
grated Win32 IDE, ANSI C-Compiler, macro assembler,
editor, linker, Liberian, C-Spy simulator/debugger, PLUS
MetaLink EPU/DM emulator support.
This section provides a summary of the tool and develop-
ment kits currently available. Up-to-date information, selec-
tion guides, free tools, demos, updates, and purchase infor-
mation can be obtained at our web site at:
www.national.com/cop8.
EWCOP8-AS: Moderately priced COP8 Assembler and
Embedded Workbench from IAR (no code limit). A fully in-
tegrated Win32 IDE, macro assembler, editor, linker, li-
brarian, and C-Spy high-level simulator/debugger with
I/O and interrupts support. (Upgradeable with optional
C-Compiler and/or MetaLink Debugger/Emulator sup-
port).
SUMMARY OF TOOLS
COP8 Evaluation Tools
•
COP8–NSEVAL: Free Software Evaluation package for
Windows. A fully integrated evaluation environment for
COP8, including versions of WCOP8 IDE (Integrated De-
velopment Environment), COP8-NSASM, COP8-MLSIM,
•
•
EWCOP8-BL: Moderately priced ANSI C-Compiler and
Embedded Workbench from IAR (Baseline version: All
COP8 devices; 4k code limit; no FP). A fully integrated
Win32 IDE, ANSI C-Compiler, macro assembler, editor,
linker, librarian, and C-Spy high-level simulator/debugger.
(Upgradeable; CWCOP8-M MetaLink tools interface sup-
port optional).
™
COP8C, DriveWay COP8, Manuals, and other COP8
information.
•
•
COP8–MLSIM: Free Instruction Level Simulator tool for
Windows. For testing and debugging software instruc-
tions only (No I/O or interrupt support).
COP8–EPU: Very Low cost COP8 Evaluation & Pro-
gramming Unit. Windows based evaluation and
hardware-simulation tool, with COP8 device programmer
and erasable samples. Includes COP8-NSDEV, Drive-
way COP8 Demo, MetaLink Debugger, I/O cables and
power supply.
EWCOP8: Full featured ANSI C-Compiler and Embed-
ded Workbench for Windows from IAR (no code limit). A
fully integrated Win32 IDE, ANSI C-Compiler, macro as-
sembler, editor, linker, librarian, and C-Spy high-level
simulator/debugger. (CWCOP8-M MetaLink tools inter-
face support optional).
www.national.com
48
COP8 Real-Time Emulation Tools
Development Support (Continued)
•
COP8-DM: MetaLink Debug Module. A moderately
•
EWCOP8-M: Full featured ANSI C-Compiler and Embed-
ded Workbench for Windows from IAR (no code limit). A
fully integrated Win32 IDE, ANSI C-Compiler, macro as-
sembler, editor, linker, librarian, C-Spy high-level
simulator/debugger, PLUS MetaLink debugger/hardware
interface (CWCOP8-M).
priced real-time in-circuit emulation tool, with COP8 de-
vice programmer. Includes MetaLink Debugger, power
supply, emulation cables and adapters.
•
IM-COP8: MetaLink iceMASTER®. A full featured, real-
time in-circuit emulator for COP8 devices. Includes
COP8-NSDEV, Driveway COP8 Demo, MetaLink Win-
dows Debugger, and power supply. Package-specific
probes and surface mount adaptors are ordered sepa-
rately.
COP8 Productivity Enhancement Tools
•
WCOP8 IDE: Very Low cost IDE (Integrated Develop-
ment Environment) from KKD. Supports COP8C, COP8-
NSASM, COP8-MLSIM, DriveWay COP8, and MetaLink
debugger under a common Windows Project Manage-
ment environment. Code development, debug, and emu-
lation tools can be launched from the project window
framework.
COP8 Device Programmer Support
•
MetaLink’s EPU and Debug Module include development
device programming capability for COP8 devices.
•
Third-party programmers and automatic handling equip-
ment cover needs from engineering prototype and pilot
production, to full production environments.
•
DriveWay-COP8: Low cost COP8 Peripherals Code
Generation tool from Aisys Corporation. Automatically
generates tested and documented C or Assembly source
code modules containing I/O drivers and interrupt han-
dlers for each on-chip peripheral. Application specific
code can be inserted for customization using the inte-
grated editor. (Compatible with COP8-NSASM, COP8C,
and WCOP8 IDE.)
•
Factory programming available for high-volume require-
ments.
TOOLS ORDERING NUMBERS FOR THE COP888xG/CS
FAMILY DEVICES
The COP888xG/CS devices are compatible with the
COP8SGx devices, and the SGx tools can be also used for
development.
•
•
COP8-UTILS: Free set of COP8 assembly code ex-
amples, device drivers, and utilities to speed up code de-
velopment.
COP8-MLSIM: Free Instruction Level Simulator tool for
Windows. For testing and debugging software instruc-
tions only (No I/O or interrupt support).
Vendor
Tools
Order Number
COP8-NSEVAL
Cost
Notes
National COP8-NSEVAL
COP8-NSASM
Free Web site download
COP8-NSASM
Free Included in EPU and DM. Web site download
Free Included in EPU and DM. Web site download
COP8-MLSIM
COP8-MLSIM
COP8-NSDEV
COP8-NSDEV
VL
VL
Included in EPU and DM. Order CD from website
COP8-EPU
COP8SG-EPU (-1 or -2)
-1 = 110V, -2 = 220V; Included p/s, 40 pin DIP target
cable, manuals, software, 16/20/28/40 DIP OTP
programming socket; add DM target adapter or OTP
adapter (if needed)
COP8-DM
COP8SG-DM (10 MHz)
M
Included p/s, 28/40/44 pin DIP/SO/PLCC target
cables, manuals, software, 16/20/28/40 DIP/SO and
44 PLCC programming socket; add OTP adapter or
target adapter (if needed)
DM Target
Adapters
DM-COP8/28D-SO
DM-COP8/44P-44Q
VL
L
28 pin DIP to SO converter
44 pin PLCC to 44 QFP converter
8k or 32k Eraseable or OTP devices
Development
Devices
COP8FGx7 (15 MHz)
COP8SGx7 (10 MHz)
VL
OTP
Programming
Adapters
COP8SA-PGMA
COP8-PGMA-44QFP
COP8-PGMA-28SO
Call MetaLink
L
For programming 28 SOIC and 44 PLCC on the EPU
For programming 44 QFP on any programmer
L
VL
For programming 16/20/28 SOIC on any programmer
IM-COP8
49
www.national.com
Development Support (Continued)
MetaLink COP8-EPU
EPU-8SGx (-1 or -2)
VL
M
1 = 110V, 2 = 220V; included p/s, 40 pin DIP target
cable, manuals, software, 16/20/28/40 DIP OTP
programming socket; add DM target adapter or OTP
adapter (if needed)
COP8-DM
DM4-COP8-888xG (x = C,
E, G, H, K) or
Included p/s (PS-10), target cable of choice (DIP or
PLCC; i.e. DM-COP8/28D), 16/20/28/40 DIP/SO and
44 PLCC programming sockets. Add OTP adapter (if
needed) and target adapter (if needed)
DM5-COP8-FGx (15
MHz) or DM4-COP8-SGx
(10 MHz), plus PS-10,
plus DM-COP8/xxx (ie.
28D)
DM Target
Adapters
MHW-CNVxx (xx = 33, 34
etc.)
L
L
DM target converters for
16DIP/20SO/28SO/44QFP/28CSP; (i.e. MHW-CNV38
for 20 pin DIP to SO package converter)
OTP
Programming
Adapters
MHW-COP8-PGMA-DS
For programming 16/20/28 SOIC and 44 PLCC on the
EPU
MHW-COP8-PGMA-44QFP
MHW-COP8-PGMA-28CSP
L
L
For programming 44 QFP on any programmer
For programming 28 CSP on any programmer
IM-COP8
IM-COP8-AD-464 (-220)
(10 MHz maximum)
H
Base unit 10 MHz; -220 = 220V; add probe card
(required) and target adapter (if needed); included
software and manuals
IM Probe Card
PC-8884xG28DW-AD-10
(x = C, E, G, K)
M
M
M
L
10 MHz 28 DIP probe card; 2.5V to 6.0V
10 MHz 40 DIP probe card; 2.5V to 6.0V
10 MHz 44 PLCC probe card; 2.5V to 6.0V
16 or 20 or 28 pin SOIC adapter for probe card
PC-888xG40DW-AD-10
(x = C, E, G, K)
PC-888xG44PW-AD-10
(x = C, E, G, K)
IM Probe Target
Adapters
MHW-SOICxx (xx = 16,
20, 28)
MHW-CONV33
L
44 pin QFP adapter for 44 PLCC probe card
No power supply
COP8-EVAL-ICUxx ICU-303
L
ICU or
National
COP8-EVAL-ICUSG
WCOP8-IDE
L
No power supply
KKD
IAR
WCOP8-IDE
EWCOP8-xx
COP8C
VL
Included in EPU and DM
See summary above
COP8C
L - H Included all software and manuals
Byte
Craft
M
Included all software and manuals
Aisys
DriveWay COP8
DriveWay COP8
Contact vendors
L
Included all software and manuals
OTP Programmers
L - H For approved programmer listings and vendor
inforamtion go to our OTP support page at:
www.national.com/cop8
<
Cost: Free; VL = $100; L = $100 - $300; M = $300 - $1k; H = $1k - $3k; VH = $3k - $5k
www.national.com
50
Development Support (Continued)
WHERE TO GET TOOLS
Tools are ordered directly from the following vendors. Please go to the vendor’s web site for current listings of distributors.
Vendor
Home Office
U.S.A.: Santa Clara, CA
1-408-327-8820
Electronic Sites
Other Main Offices
Distributors
Aisys
www.aisysinc.com
@
info aisysinc.com
fax: 1-408-327-8830
U.S.A.
Byte Craft
IAR
www.bytecraft.com
Distributors
@
1-519-888-6911
info bytecraft.com
fax: 1-519-746-6751
Sweden: Uppsala
+46 18 16 78 00
fax: +46 18 16 78 38
www.iar.se
U.S.A.: San Francisco
1-415-765-5500
@
info iar.se
@
info iar.com
fax: 1-415-765-5503
U.K.: London
@
info iarsys.co.uk
@
info iar.de
+44 171 924 33 34
fax: +44 171 924 53 41
Germany: Munich
+49 89 470 6022
fax: +49 89 470 956
Switzeland: Hoehe
+41 34 497 28 20
fax: +41 34 497 28 21
ICU
Sweden: Polygonvaegen
+46 8 630 11 20
www.icu.se
@
support icu.se
@
fax: +46 8 630 11 70
Denmark:
support icu.ch
KKD
www.kkd.dk
MetaLink
U.S.A.: Chandler, AZ
1-800-638-2423
www.metaice.com
Germany: Kirchseeon
80-91-5696-0
@
sales metaice.com
@
fax: 1-602-926-1198
support metaice.com
fax: 80-91-2386
@
bbs: 1-602-962-0013
www.metalink.de
islanger metalink.de
Distributors Worldwide
National
U.S.A.: Santa Clara, CA
1-800-272-9959
www.national.com/cop8
Europe: +49 (0) 180 530 8585
fax: +49 (0) 180 530 8586
Distributors Worldwide
@
support nsc.com
@
fax: 1-800-737-7018
europe.support nsc.com
The following companies have approved COP8 program-
mers in a variety of configurations. Contact your local office
or distributor. You can link to their web sites and get the lat-
est listing of approved programmers from National’s COP8
OTP Support page at: www.national.com/cop8.
CUSTOMER SUPPORT
Complete product information and technical support is avail-
able from National’s customer response centers, and from
our on-line COP8 customer support sites.
Advantech; Advin; BP Microsystems; Data I/O; Hi-Lo Sys-
tems; ICE Technology; Lloyd Research; Logical Devices;
MQP; Needhams; Phyton; SMS; Stag Programmers; Sys-
tem General; Tribal Microsystems; Xeltek.
51
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
Molded Dual-In-Line Package (N)
Order Number COP688KG-XXX/N, COP888KG-XXX/N
NS Package Number N40A
Plastic Leaded Chip Carrier (V)
Order Number COP688KG-XXXV, COP888KG-XXX/V
NS Package Number V44A
www.national.com
52
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明