DAC7821IPWRG4 [TI]
12-Bit, Parallel Input, Multiplying Digital-to-Analog Converter; 12位并行输入,乘法数位类比转换器型号: | DAC7821IPWRG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | 12-Bit, Parallel Input, Multiplying Digital-to-Analog Converter |
文件: | 总18页 (文件大小:1611K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DAC7821
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
12-Bit, Parallel Input, Multiplying
Digital-to-Analog Converter
FEATURES
DESCRIPTION
•
2.5 V to 5.5 V Supply Operation
The DAC7821 is a CMOS 12-bit current output
digital-to-analog converter (DAC). This device
operates from a single 2.5 V to 5.5 V power supply,
making it suitable to battery-powered and many other
applications.
•
Fast Parallel Interface:
17ns Write Cycle
•
•
•
•
•
Update Rate of 20.4 MSPS
10 MHz Multiplying Bandwidth
±10 V Reference Input
This DAC operates with a fast parallel interface. Data
readback allows the user to read the contents of the
DAC register via the DB pins. On power-up, the
internal register and latches are filled with zeroes and
the DAC outputs are at zero scale.
Low Glitch Energy: 5 nV-s
Extended Temperature Range:
–40°C to +125°C
The
DAC7821
offers
excellent
4-quadrant
•
•
•
•
•
•
•
20-Lead QFN and 20-Lead TSSOP Packages
12-Bit Monotonic
multiplication characteristics, with large signal
multiplying bandwidth of 10 MHz. The applied
external reference input voltage (VREF) determines
the full-scale output current. An integrated feedback
resistor (RFB) provides temperature tracking and
full-scale voltage output when combined with an
external current-to-voltage precision amplifier.
±1 LSB INL
4-Quadrant Multiplication
Power-On Reset with Brownout Detection
Readback Function
Industry-Standard Pin Configuration
The DAC7821 is available in a 20-lead TSSOP
package as well as a small 20-lead QFN package
(available Q2 2006).
APPLICATIONS
•
•
•
•
•
•
•
•
Portable Battery-Powered Instruments
Waveform Generators
Analog Processing
Programmable Amplifiers and Attenuators
Digitally-Controlled Calibration
Programmable Filters and Oscillators
Composite Video
V
DD
V
REF
R
DAC7821
R
FB
I 1
OUT
12-Bit
Power-On
Reset
R-2R DAC
I 2
OUT
Ultrasound
DAC Register
Input Latch
CS
Control
Logic
R/W
Parallel Bus
DB0
DB11
GND
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2006, Texas Instruments Incorporated
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION(1)
SPECIFIED
PACKAGE
DESIGNATOR
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT MEDIA,
QUANTITY
PRODUCT
PACKAGE
DAC7821IPW
DAC7821IPWR
DAC7821IRGPT
DAC7821IRGPR
70, Tube
DAC7821
20-TSSOP
PW
–40°C to +125°C
–40°C to +125°C
DAC7821
DAC7821
2000, Tape and Reel
250, Tape and Reel
3000, Tape and Reel
DAC7821
20-QFN(2)
RGP
(1) For the most current specifications and package information, see the Package Option Addendum located at the end of this data sheet or
refer to our web site at www.ti.com.
(2) Available 2Q 2006.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)(1)
DAC7821
–0.3 to +7.0
–0.3 to VDD + 0.3
–0.3 to VDD + 0.3
–40 to +125
–65 to +150
+150
UNIT
V
VDD to GND
Digital input voltage to GND
VOUT to GND
V
V
Operating temperature range
Storage temperature range
Junction temperature (TJ max)
ESD Rating, HBM
°C
°C
°C
V
3000
ESD Rating, CDM
1000
V
(1) Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. Exposure to absolute
maximum conditions for extended periods may affect device reliability.
2
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
ELECTRICAL CHARACTERISTICS
VDD = +2.5 V to +5.5 V; IOUT1 = Virtual GND; IOUT2 = 0V; VREF = +10 V; TA = full operating temperature. All specifications
–40°C to +125°C, unless otherwise noted.
DAC7821
PARAMETER
STATIC PERFORMANCE
Resolution
CONDITIONS
MIN
TYP
MAX
UNITS
12
Bits
LSB
LSB
nA
Relative accuracy
±1
±1
Differential nonlinearity
Output leakage current
Output leakage current
Full-scale gain error
Full-scale tempco
Data = 000h, TA = +25°C
±10
±20
±10
Data = 000h, TA = TMAX
nA
All ones loaded to DAC register
±5
±5
30
mV
ppm/°C
pF
Output capacitance
REFERENCE INPUT
VREF range
Code dependent
–15
8
15
12
12
V
Input resistance
10
10
kΩ
kΩ
RFB resistance
8
LOGIC INPUTS AND OUTPUT(1)
Input low voltage
VIL VDD = +2.7V
0.6
0.8
V
V
VIL VDD = +5V
VIH VDD = +2.7V
VIH VDD = +5V
IIL
Input high voltage
2.1
2.4
V
V
Input leakage current
Input capacitance
10
10
µA
pF
CIL
POWER REQUIREMENTS
VDD
2.7
5.5
5
V
IDD (normal operation)
VDD = +4.5 V to +5.5 V
VDD = +2.5 V to +3.6 V
AC CHARACTERISTICS
Output voltage settling time
Reference multiplying BW
Logic inputs = 0 V
µA
µA
µA
VIH = VDD and VIL = GND
VIH = VDD and VIL = GND
0.8
0.4
5
2.5
0.2
µs
VREF = 7 VPP, Data = FFFh
10
5
MHz
VREF = 0 V to 10 V,
Data = 7FFh to 800h to 7FFh
DAC glitch impulse
nV-s
Feedthrough error VOUT/VREF
Digital feedthrough
Data = 000h, VREF = 100kHz
–70
2
dB
nV-s
dB
Total harmonic distortion
Output spot noise voltage
–105
18
nV/√Hz
(1) Specified by design and characterization; not production tested.
3
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
TIMING INFORMATION
t
1
t
6
t
t
2
2
R/W
t
7
t
3
CS
t
4
t
8
t
9
t
5
DATA
DATA VALID
DATA VALID
TIMING REQUIREMENTS: 2.5 V to 4.5 V
At tr = tf = 1 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2; VDD = +2.5 V to +4.5 V, VREF = +10 V,
IOUT2 = 0 V. All specifications –40°C to +125°C, unless otherwise noted.
DAC7821
PARAMETER(1)
TEST CONDITIONS
R/W to CS setup time
MIN
0
TYP
MAX
UNIT
ns
t1
t2
t3
t4
t5
t6
t7
t8
t9
R/W to CS hold time
CS low time (write cycle)
Data setup time
0
ns
10
6
ns
ns
Data hold time
0
ns
R/W high to CS low
CS min high time
Data access time
Bus relinquish time
5
ns
9
ns
20
5
40
10
ns
ns
(1) Ensured by design; not production tested.
TIMING REQUIREMENTS: 4.5 V to 5.5 V
At tr = tf = 1 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2; VDD = +4.5 V to +5.5 V, VREF = +10 V,
IOUT2 = 0 V. All specifications –40°C to +125°C, unless otherwise noted.
DAC7821
PARAMETER(1)
TEST CONDITIONS
R/W to CS setup time
MIN
0
TYP
MAX
UNIT
ns
t1
t2
t3
t4
t5
t6
t7
t8
t9
R/W to CS hold time
CS low time (write cycle)
Data setup time
0
ns
10
6
ns
ns
Data hold time
0
ns
R/W high to CS low
CS min high time
Data access time
Bus relinquish time
5
ns
7
ns
10
5
20
10
ns
ns
(1) Ensured by design; not production tested.
4
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
DEVICE INFORMATION
I
1
1
2
3
4
5
6
7
8
9
20
19
18
R
OUT
FB
I
2
V
OUT
REF
GND
DB11 (MSB)
DB10
V
DD
GND
1
2
3
4
5
15 R/W
14 CS
17 R/W
16 CS
DB11
DB10
DB9
DAC7821
13 DB0
12 DB1
11 DB2
DAC7821
DB9
15 DB0 (LSB)
14 DB1
13 DB2
12 DB3
11 DB4
DB8
DB8
DB7
DB6
DB5 10
(1)
QFN-20
TSSOP-20
(1)
QFN-20 package available 2Q 2006.
TERMINAL FUNCTIONS
TERMINAL
TSSOP
NO.
QFN
NO.
NAME
DESCRIPTION
1
2
19
IOUT
IOUT
1
2
DAC current output.
20
DAC analog ground. This pin is normally tied to the analog ground of the system.
Ground pin.
3
1
GND
4–15
2–13
DB11 – DB0 Parallel data bits 11 to 0.
Chip select input. Active low. Used in conjunction with R/W to load parallel data to the input
latch or read data from the DAC register. Rising edge of CS loads data.
16
17
14
15
CS
Read/Write. When low, use in conjunction with CS to load parallel data. When high, use with
CS to read back contents of DAC register.
R/W
18
19
16
17
VDD
Positive power supply input. These parts can be operated from a supply of 2.5 V to 5.5 V.
DAC reference voltage input.
VREF
DAC feedback resistor pin. Establish voltage output for the DAC by connecting to external
amplifier output.
20
18
RFB
5
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
TYPICAL CHARACTERISTICS: VDD = +5 V
At TA = +25°C, unless otherwise noted.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
1.0
0.8
1.0
0.8
T
A
= +25°C
T = +25°C
A
V
REF
= +10 V
V
REF
= +10 V
0.6
0.6
0.4
0.4
0.2
0.2
0
0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
0
0
0
512 1024 1536 2048 2560 3072 3584 4095
0
0
0
512 1024 1536 2048 2560 3072 3584 4095
Digital Input Code
Digital Input Code
Figure 1.
Figure 2.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
1.0
0.8
1.0
0.8
T
A
= -40°C
= +10 V
T
A
= -40°C
= +10 V
REF
V
V
REF
0.6
0.6
0.4
0.4
0.2
0.2
0
0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
512 1024 1536 2048 2560 3072 3584 4095
512 1024 1536 2048 2560 3072 3584 4095
Digital Input Code
Digital Input Code
Figure 3.
Figure 4.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
1.0
0.8
1.0
0.8
T
A
= +125°C
= +10 V
T
A
= +125°C
V = +10 V
REF
V
REF
0.6
0.6
0.4
0.4
0.2
0.2
0
0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
512 1024 1536 2048 2560 3072 3584 4095
512 1024 1536 2048 2560 3072 3584 4095
Digital Input Code
Digital Input Code
Figure 5.
Figure 6.
6
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
TYPICAL CHARACTERISTICS: VDD = +5 V (continued)
At TA = +25°C, unless otherwise noted.
SUPPLY CURRENT
vs LOGIC INPUT VOLTAGE
REFERENCE MULTIPLYING BANDWIDTH
3.0
6
0
0xFFF
0x800
0x400
0x200
0x100
0x080
0x040
0x020
0x010
0x008
0x004
0x002
0x001
V
= 5.0 V
DD
-6
2.5
2.0
1.5
1.0
0.5
0
-12
-18
-24
-30
-36
-42
-48
-56
-60
-66
-72
-78
-84
-90
-96
-102
V
DD
= 3.0 V
V
= 2.5 V
DD
0x000
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
10
100
10k
100k
10M
100M
1k
1M
Logic Input Voltage (V)
Bandwidth (Hz)
Figure 7.
Figure 8.
MIDSCALE DAC GLITCH
MIDSCALE DAC GLITCH
Code 2047 to 2048
Code 2048 to 2047
DAC Update
DAC Update
Time (50ns/div)
Time (50ns/div)
Figure 9.
Figure 10.
DAC SETTLING TIME
GAIN ERROR
vs TEMPERATURE
0
V
= I
OUT
x 100 W
OUT
-0.2
-0.4
-0.6
-0.8
-1.0
-1.2
-1.4
-1.6
-1.8
--2.0
Small Signal Settling
DAC Update
V
= +10 V
REF
Time (20 ns/div)
-40
-20
0
20
40
60
80
100
120
Temperature (°C)
Figure 11.
Figure 12.
7
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
TYPICAL CHARACTERISTICS: VDD = +5 V (continued)
At TA = +25°C, unless otherwise noted.
SUPPLY CURRENT
vs TEMPERATURE
LEAKAGE CURRENT
vs TEMPERATURE
2.0
0.2
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0
V
= +10 V
REF
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
V
= +5.0 V
DD
V
= +2.5 V
DD
-40
-20
0
20
40
60
80
100
120
-40
-20
0
20
40
60
80
100
120
Temperature (°C)
Temperature (°C)
Figure 13.
Figure 14.
8
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
TYPICAL CHARACTERISTICS: VDD = +2.5 V
At TA = +25°C, unless otherwise noted.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
1.0
1.0
0.8
T
A
= +25°C
T = +25°C
A
0.8
V
REF
= +10 V
V
REF
= +10 V
0.6
0.4
0.6
0.4
0.2
0.2
0
0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
0
0
0
512 1024 1536 2048 2560 3072 3584 4095
0
0
0
512 1024 1536 2048 2560 3072 3584 4095
Digital Input Code
Digital Input Code
Figure 15.
Figure 16.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
1.0
0.8
1.0
0.8
T
A
= -40°C
= +10 V
T
A
= -40°C
= +10 V
REF
V
V
REF
0.6
0.6
0.4
0.4
0.2
0.2
0
0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
512 1024 1536 2048 2560 3072 3584 4095
512 1024 1536 2048 2560 3072 3584 4095
Digital Input Code
Digital Input Code
Figure 17.
Figure 18.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
1.0
0.8
1.0
0.8
T
A
= +125°C
= +10 V
T
A
= +125°C
V = +10 V
REF
V
REF
0.6
0.6
0.4
0.4
0.2
0.2
0
0
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
512 1024 1536 2048 2560 3072 3584 4095
512 1024 1536 2048 2560 3072 3584 4095
Digital Input Code
Digital Input Code
Figure 19.
Figure 20.
9
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
TYPICAL CHARACTERISTICS: VDD = +2.5 V (continued)
At TA = +25°C, unless otherwise noted.
MIDSCALE DAC GLITCH
MIDSCALE DAC GLITCH
Code 2047 to 2048
Code 2048 to 2047
DAC Update
DAC Update
Time (50ns/div)
Time (50ns/div)
Figure 21.
Figure 22.
GAIN ERROR
vs TEMPERATURE
LEAKAGE CURRENT
vs TEMPERATURE
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0.2
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
0
V
REF
= +10 V
-40
-20
0
20
40
60
80
100
120
-40
-20
0
20
40
60
80
100
120
Temperature (°C)
Temperature (°C)
Figure 23.
Figure 24.
10
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
THEORY OF OPERATION
The DAC7821 is a single channel current output, 12-bit digital-to-analog converter (DAC). The architecture,
illustrated in Figure 25, is an R-2R ladder configuration with the three MSBs segmented. Each 2R leg of the
ladder is either switched to IOUT1 or the IOUT2 terminal. The IOUT1 terminal of the DAC is held at a virtual GND
potential by the use of an external I/V converter op amp. The R-2R ladder is connected to an external reference
input VREF that determines the DAC full-scale current. The R-2R ladder presents a code-independent load
impedance to the external reference of 10 kΩ ±20%. The external reference voltage can vary over a range of
–15 V to +15 V, thus providing bipolar IOUT current operation. By using an external I/V converter and the
DAC7821 RFB resistor, output voltage ranges of –VREF to VREF can be generated.
R
R
R
R
V
REF
2R
2R
2R
2R
2R
R
FB
I
1
OUT
I
2
OUT
DB11
(MSB)
DB10
DB9
DB0
(LSB)
Figure 25. Equivalent R-2R DAC Circuit
When using an external I/V converter and the DAC7821 RFB resistor, the DAC output voltage is given by
Equation 1:
CODE
4096
(VOUT + ) VREF
(1)
Each DAC code determines the 2R leg switch position to either GND or IOUT. Because the DAC output
impedance as seen looking into the IOUT1 terminal changes versus code, the external I/V converter noise gain
will also change. Because of this, the external I/V converter op amp must have a sufficiently low offset voltage
such that the amplifier offset is not modulated by the DAC IOUT1 terminal impedance change. External op amps
with large offset voltages can produce INL errors in the transfer function of the DAC7821 as a result of offset
modulation versus DAC code.
For best linearity performance of the DAC7821, an op amp with a low input offset voltage (OPA277) is
recommended (see Figure 26). This circuit allows VREF swinging from –10 V to +10 V.
V
DD
15V
V
DD
R
FB
V+
OPA277
V-
DAC7821
I
1
V
OUT
REF
V
OUT
I
2
GND
OUT
-15V
Figure 26. Voltage Output Configuration
11
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
APPLICATION INFORMATION
Stability Circuit
For a current-to-voltage design (see Figure 27), the DAC7821 current output (IOUT) and the connection with the
inverting node of the op amp should be as short as possible and according to correct printed circuit board (PCB)
layout design. For each code change, there is a step function. If the gain bandwidth product (GBP) of the op amp
is limited and parasitic capacitance is excessive at the inverting node, then gain peaking is possible. Therefore,
for circuit stability, a compensation capacitor C1 (1 pF to 5 pF typ) can be added to the design, as shown in
Figure 27.
V
DD
U1
V
DD
R
FB
C
1
I
1
V
V
REF
OUT
REF
V
OUT
I
2
GND
OUT
U2
Figure 27. Gain Peaking Prevention Circuit with Compensation Capacitor
Positive Voltage Output Circuit
As Figure 28 illustrates, in order to generate a positive voltage output, a negative reference is input to the
DAC7821. This design is suggested instead of using an inverting amp to invert the output as a result of resistor
tolerance errors. For a negative reference, VOUT and GND of the reference are level-shifted to a virtual ground
and a –2.5 V input to the DAC7821 with an op amp.
+2.5 V Reference
V
DD
V
V
IN
OUT
GND
V
DD
R
FB
C
1
V
REF
DAC7821
I
1
OPA277
OUT
-2.5V
OPA277
V
OUT
I
2
GND
OUT
0 < V
< +2.5 V
OUT
Figure 28. Positive Voltage Output Circuit
Bipolar Output Section
The DAC7821, as a 2-quadrant multiplying DAC, can be used to generate a unipolar output. The polarity of the
full-scale output IOUT is the inverse of the input reference voltage at VREF
.
Some applications require full 4-quadrant multiplying capabilities or bipolar output swing. As shown in Figure 29,
external op amp U4 is added as a summing amp and has a gain of 2X that widens the output span to 5 V. A
4-quadrant multiplying circuit is implemented by using a 2.5 V offset of the reference voltage to bias U4.
According to the circuit transfer equation given in Equation 2, input data (D) from code 0 to full-scale produces
output voltages of VOUT = –2.5 V to VOUT = +2.5 V.
D
(VOUT
+
)1 VREF
0.5 2N
(2)
12
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
APPLICATION INFORMATION (continued)
External resistance mismatching is the significant error in Figure 29.
10 kW
10 kW
C
2
V
DD
5 kW
U4
OPA277
V
OUT
V
R
FB
C
DD
1
V
I
1
+2.5 V
(+10 V)
DAC7821
REF
OUT
U2
OPA277
I
2
GND
OUT
-2.5 V £ V
£ +2.5 V
OUT
(-10 V £ V
£ +10 V)
OUT
Figure 29. Bipolar Output Circuit
Programmable Current Source Circuit
A DAC7821 can be integrated into the circuit in Figure 30 to implement an improved Howland current pump for
precise voltage-to-current conversions. Bidirectional current flow and high voltage compliance are two features of
the circuit. With a matched resistor network, the load current of the circuit is shown by Equation 3:
(
)
R2 R3 R1
IL +
VREF D
R3
(3)
The value of R3 in the previous equation can be reduced to increase the output current drive of U3. U3 can drive
±20 mA in both directions with voltage compliance limited up to 15 V by the U3 voltage supply. Elimination of the
circuit compensation capacitor C1 in the circuit is not suggested as a result of the change in the output
impedance ZO, according to Equation 4:
(
)
R1 R3 R1 R2
ZO +
(
)
(
)
R1 R2Ȁ R3Ȁ ) R1Ȁ R2 R3
(4)
As shown in Equation 4, with matched resistors, ZO is infinite and the circuit is optimum for use as a current
source. However, if unmatched resistors are used, ZO is positive or negative with negative output impedance
being a potential cause of oscillation. Therefore, by incorporating C1 into the circuit, possible oscillation problems
are eliminated. The value of C1 can be determined for critical applications; for most applications, however, a
value of several pF is suggested.
R2¢
15 kW
C1
10 pF
R1¢
V
R3¢
DD
150 kW
50 W
U3
V
OUT
OPA277
V
R
FB
DD
U1
R3
DAC7821
I
1
V
OUT
REF
U2
OPA277
R1
R2
50 W
I
2
GND
OUT
150 kW
15 kW
I
L
LOAD
Figure 30. Programmable Bidirectional Current Source Circuit
13
DAC7821
www.ti.com
SBAS365A–OCTOBER 2005–REVISED FEBRUARY 2006
APPLICATION INFORMATION (continued)
Parallel Interface
Data is loaded to the DAC7821 as a 12-bit parallel word. The bi-directional bus is controlled with CS and R/W,
allowing data to be written to or read from the DAC register. To write to the device, CS and R/W are brought low,
and data available on the data lines fills the input register. The rising edge of CS latches the data and transfers
the latched data-word to the DAC register. The DAC latches are not transparent; therefore, a write sequence
must consist of a falling and rising edge on CS in order to ensure that data is loaded to the DAC register and its
analog equivalent is reflected on the DAC output.
To read data stored in the device, R/W is held high and CS is brought low. Data is loaded from the DAC register
back to the input register and out onto the data line, where it can be read back to the controller.
Cross-Reference
The DAC7821 has an industry-standard pinout. Table 1 provides the cross-reference information.
Table 1. Cross-Reference
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
PACKAGE
OPTION
CROSS-
REFERENCE PART
PRODUCT
DAC7821
DAC7821
INL (LSB)
DNL (LSB)
±1
±1
±1
±1
–40°C to +125°C
–40°C to +125°C
20-Lead TSSOP
20-Lead QFN(1)
TSSOP-20
QFN-20
AD5445
AD5445
(1) Available 2Q 2006.
14
PACKAGE OPTION ADDENDUM
www.ti.com
3-Apr-2006
PACKAGING INFORMATION
Orderable Device
DAC7821IPW
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
TSSOP
PW
20
20
20
20
78 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
DAC7821IPWG4
DAC7821IPWR
DAC7821IPWRG4
TSSOP
TSSOP
TSSOP
PW
PW
PW
78 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
DAC7821IRGPR
DAC7821IRGPT
PREVIEW
PREVIEW
QFN
QFN
RGP
RGP
20
20
3000
250
TBD
TBD
Call TI
Call TI
Call TI
Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
M
0,10
0,65
14
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°–8°
A
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
8
14
16
20
24
28
DIM
3,10
2,90
5,10
4,90
5,10
4,90
6,60
6,40
7,90
9,80
9,60
A MAX
A MIN
7,70
4040064/F 01/97
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2006, Texas Instruments Incorporated
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明