DAC908U/1KG4 [TI]
8-Bit, 165MSPS DIGITAL-TO-ANALOG CONVERTER; 8位, 165MSPS数位类比转换器![DAC908U/1KG4](http://pdffile.icpdf.com/pdf2/p00207/img/icpdf/DAC908_1170723_icpdf.jpg)
型号: | DAC908U/1KG4 |
厂家: | ![]() |
描述: | 8-Bit, 165MSPS DIGITAL-TO-ANALOG CONVERTER |
文件: | 总23页 (文件大小:789K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
DAC908
8
0
9
C
A
D
SBAS109B – JUNE 2003
TM
8-Bit, 165MSPS
DIGITAL-TO-ANALOG CONVERTER
FEATURES
● SINGLE +5V OR +3V OPERATION
APPLICATIONS
● MEDICAL INSTRUMENTATION
Ultrasound (DBF)
●
HIGH SFDR: 5.04MHz Output at 100MSPS: 67dBc
● VIDEO, DIGITAL TV
● LOW GLITCH: 3pV-s
● WAVEFORM GENERATION
● LOW POWER: 170mW at +5V
Direct Digital Synthesis (DDS)
● INTERNAL REFERENCE:
Optional Ext. Reference
Adjustable Full-Scale Range
Multiplying Option
Arbitrary Waveform Generation (ARB)
● TEST INSTRUMENTATION
● COMMUNICATIONS
For noncontinuous operation of the DAC908, a power-down mode
results in only 45mW of standby power.
DESCRIPTION
The DAC908 is a high-speed, Digital-to-Analog Converter (DAC)
offering an 8-bit resolution option within the SpeedPlus family of
high-performance converters. Featuring pin compatibility among
family members, the DAC900, DAC902, and DAC904 provide a
component selection option to an 10-, 12-, and 14-bit resolution,
respectively. All models within this family of DACs support update
rates in excess of 165MSPS with excellent dynamic performance,
and are especially suited to fulfill the demands of a variety of
applications.
The DAC908 comes with an integrated 1.24V bandgap reference
and edge-triggered input latches, offering a complete converter
solution. Both +3V and +5V CMOS logic families can be inter-
faced to the DAC908.
The reference structure of the DAC908 allows for additional
flexibility by utilizing the on-chip reference, or applying an exter-
nal reference. The full-scale output current can be adjusted over a
span of 2mA to 20mA, with one external resistor, while maintain-
ing the specified dynamic performance.
The advanced segmentation architecture of the DAC908 is opti-
mized to provide a high Spurious-Free Dynamic Range (SFDR) for
single-tone, as well as for multi-tone signals—essential when used
for the transmit signal path of communication systems.
The DAC908 is available in the SO-28 and TSSOP-28 packages.
+VA
BW
+VD
DAC908
The DAC908 has a high impedance (200kΩ) current output with a
nominal range of 20mA and an output compliance of up to 1.25V.
The differential outputs allow for both a differential or single-
ended analog signal interface. The close matching of the current
outputs ensures superior dynamic performance in the differential
configuration, which can be implemented with a transformer.
IOUT
IOUT
BYP
LSB
Switches
FSA
Current
Sources
REFIN
Segmented
Switches
INT/EXT
Utilizing a small geometry CMOS process, the monolithic DAC908
can be operated on a wide, single-supply range of +2.7V to +5.5V.
Its low power consumption allows for use in portable and battery-
operated systems. Further optimization can be realized by lowering
the output current with the adjustable full-scale option.
Latches
PD
+1.24V Ref.
8-Bit Data Input
D7...D0
AGND
CLK
DGND
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2002-2003, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ABSOLUTE MAXIMUM RATINGS
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instru-
mentsrecommendsthatallintegratedcircuitsbehandledwith
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
+VA to AGND ........................................................................ –0.3V to +6V
+VD to DGND ........................................................................ –0.3V to +6V
AGND to DGND ................................................................. –0.3V to +0.3V
+VA to +VD ............................................................................... –6V to +6V
CLK, PD to DGND ..................................................... –0.3V to VD + 0.3V
D0-D7 to DGND ......................................................... –0.3V to VD + 0.3V
IOUT, IOUT to AGND ........................................................ –1V to VA + 0.3V
BW, BYP to AGND ..................................................... –0.3V to VA + 0.3V
REFIN, FSA to AGND ................................................. –0.3V to VA + 0.3V
INT/EXT to AGND ...................................................... –0.3V to VA + 0.3V
Junction Temperature .................................................................... +150°C
Case Temperature ......................................................................... +100°C
Storage Temperature .................................................................... +125°C
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
PACKAGE
DRAWING
NUMBER
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(1)
TRANSPORT
MEDIA
PRODUCT
PACKAGE
DAC908U
SO-28
217
"
360
"
–40°C to +85°C
DAC908U
DAC908U
DAC908U/1K
DAC908E
Rails
Tape and Reel
Rails
"
DAC908E
"
"
"
"
TSSOP-28
–40°C to +85°C
DAC908E
"
"
"
DAC908E/2K5
Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces
of “DAC908E/2K5” will get a single 2500-piece Tape and Reel.
DEMO BOARD ORDERING INFORMATION
DEMO BOARD
PRODUCT
ORDERING NUMBER
COMMENT
DAC908U
DAC908E
DEM-DAC90xU
DEM-DAC908E
Populated evaluation board without DAC. Order sample of desired DAC90x model separately.
Populated evaluation board including the DAC908E.
ELECTRICAL CHARACTERISTICS
At TA = full specified temperature range, +VA = +5V, +VD = +5V, differential transformer coupled output, 50Ω doubly terminated, unless otherwise specified.
DAC908U/E
PARAMETER
RESOLUTION
CONDITIONS
MIN
TYP
MAX
UNITS
8
Bits
OUTPUT UPDATE RATE
Output Update Rate (fCLOCK
Full Specified Temperature Range, Operating
2.7V to 3.3V
4.5V to 5.5V
Ambient, TA
125
165
–40
165
200
MSPS
MSPS
°C
)
+85
STATIC ACCURACY(1)
TA = +25°C
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)
fCLOCK = 25MSPS, fOUT = 1.0MHz
–0.5
–0.5
±0.25
±0.25
+0.5
+0.5
LSB
LSB
DYNAMIC PERFORMANCE
TA = +25°C
Spurious-Free Dynamic Range (SFDR)
fOUT = 1.0MHz, fCLOCK = 25MSPS
fOUT = 2.1MHz, fCLOCK = 50MSPS
fOUT = 5.04MHz, fCLOCK = 50MSPS
fOUT = 5.04MHz, fCLOCK = 100MSPS
fOUT = 20.2MHz, fCLOCK = 100MSPS
fOUT = 25.3MHz, fCLOCK = 125MSPS
fOUT = 41.5MHz, fCLOCK = 125MSPS
fOUT = 27.4MHz, fCLOCK = 165MSPS
fOUT = 54.8MHz, fCLOCK = 165MSPS
Spurious-Free Dynamic Range within a Window
fOUT = 2.1MHz, fCLOCK = 50MSPS
fOUT = 5.04MHz, fCLOCK = 100MSPS
Total Harmonic Distortion (THD)
To Nyquist
64
70
69
67
67
61
57
51
58
52
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
2MHz Span
4MHz Span
70
69
dBc
dBc
fOUT = 2.1MHz, fCLOCK = 50MSPS
fOUT = 5.04MHz, fCLOCK = 100MSPS
fOUT = 20.2MHz, fCLOCK = 100MSPS
–72
–66
–60
dBc
dBc
dBc
DAC908
2
SBAS109B
ELECTRICAL CHARACTERISTICS (Cont.)
At TA = +25°C, +VA = +5V, +VD = +5V, differential transformer coupled output, 50Ω doubly terminated, unless otherwise specified.
DAC908U/E
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
DYNAMIC PERFORMANCE (Cont.)
Output Settling Time(2)
Output Rise Time(2)
to 0.1%
10% to 90%
10% to 90%
30
2
2
ns
ns
ns
Output Fall Time(2)
Glitch Impulse
3
pV-s
DC-ACCURACY
Full-Scale Output Range(3)(FSR)
Output Compliance Range
Gain Error
Gain Error
Gain Drift
All Bits High, IOUT
2.0
–1.0
–10
–10
20.0
+1.25
+10
mA
V
With Internal Reference
With External Reference
With Internal Reference
With Internal Reference
With Internal Reference
±1
±2
±120
%FSR
%FSR
ppmFSR/°C
%FSR
ppmFSR/°C
%FSR/V
%FSR/V
pA/√Hz
kΩ
+10
Offset Error
Offset Drift
–0.025
+0.025
±0.1
Power-Supply Rejection, +VA
Power- Supply Rejection, +VD
Output Noise
Output Resistance
Output Capacitance
–0.2
–0.025
+0.2
+0.025
I
OUT = 20mA, RLOAD = 50Ω
50
200
12
I
OUT, IOUT to Ground
pF
REFERENCE
Reference Voltage
Reference Tolerance
+1.24
±5
V
%
Reference Voltage Drift
Reference Output Current
Reference Input Resistance
Reference Input Compliance Range
Reference Small-Signal Bandwidth(4)
±50
10
1
ppmFSR/°C
µA
MΩ
V
0.1
1.25
1.3
MHz
DIGITAL INPUTS
Logic Coding
Straight Binary
Latch Command
Rising Edge of Clock
Logic High Voltage, VIH
Logic Low Voltage, VIL
Logic High Voltage, VIH
Logic Low Voltage, VIL
+VD = +5V
+VD = +5V
+VD = +3V
+VD = +3V
+VD = +5V
+VD = +5V
3.5
2
5
0
3
V
V
V
1.2
0.8
0
V
(5)
Logic High Current, IIH
±20
±20
5
µA
µA
pF
Logic Low Current, IIL
Input Capacitance
POWER SUPPLY
Supply Voltages
+VA
+VD
+2.7
+2.7
+5
+5
+5.5
+5.5
V
V
Supply Current(6)
IVA
24
1.1
8
170
50
45
30
2
15
230
mA
mA
mA
mW
mW
mW
IVA, Power-Down Mode
IVD
Power Dissipation
+5V, IOUT = 20mA
+3V, IOUT = 2mA
Power Dissipation, Power-Down Mode
Thermal Resistance, θJA
SO-28
75
50
°C/W
°C/W
TSSOP-28
NOTES: (1) At output IOUT, while driving a virtual ground. (2) Measured single-ended into 50Ω Load. (3) Nominal full-scale output current is 32x IREF; see Application
Section for details. (4) Reference bandwidth depends on size of external capacitor at the BW pin and signal level. (5) Typically 45µA for the PD pin, which has an
internal pull-down resistor. (6) Measured at fCLOCK = 50MSPS and fOUT = 1.0MHz.
DAC908
SBAS109B
3
PIN CONFIGURATION
PIN DESCRIPTIONS
PIN
DESIGNATOR
DESCRIPTION
Top View
SO, TSSOP
1
2
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8
NC
Data Bit 1 (D7), MSB
Data Bit 2 (D6)
Data Bit 3 (D5)
Data Bit 4 (D4)
Data Bit 5 (D3)
Data Bit 6 (D2)
Data Bit 7 (D1)
Data Bit 8 (D0), LSB
No Connection
No Connection
No Connection
No Connection
No Connection
No Connection
3
4
5
(MSB) Bit 1
Bit 2
1
2
3
4
5
6
7
8
9
28 CLK
27 +VD
6
7
8
Bit 3
26 DGND
25 NC(1)
24 +VA
9
10
11
12
13
14
15
NC
Bit 4
NC
NC
Bit 5
NC
Bit 6
23 BYP
22 IOUT
NC
PD
Power Down, Control Input; Active
HIGH. Contains internal pull-down circuit;
may be left unconnected if not used.
Reference Select Pin; Internal (= 0) or
External (= 1) Reference Operation.
Reference Input/Ouput. See Applications
section for further details.
Bit 7
DAC908
(LSB) Bit 8
NC(1)
21 IOUT
16
17
INT/EXT
REFIN
20 AGND
19 BW
NC(1) 10
NC(1) 11
NC(1) 12
NC(1) 13
NC(1) 14
18
19
FSA
BW
Full-Scale Output Adjust
Bandwidth/Noise Reduction Pin:
Bypass with 0.1µF to +VA for Optimum
Performance.
18 FSA
17 REFIN
16 INT/EXT
15 PD
20
21
22
23
24
25
26
27
28
AGND
IOUT
Analog Ground
Complementary DAC Current Output
DAC Current Output
IOUT
BYP
+VA
Bypass Node: Use 0.1µF to AGND
Analog Supply Voltage, 2.7V to 5.5V
No Connection
NOTE: (1) NC pins should be left unconnected or grounded.
NC
DGND
+VD
Digital Ground
Digital Supply Voltage, 2.7V to 5.5V
Clock Input
CLK
TYPICAL CONNECTION CIRCUIT
+5V
+5V
0.1µF
+VA
DAC908
+VD
BW
IOUT
IOUT
1:1
LSB
FSA
Switches
BYP
Current
Sources
REFIN
Segmented
MSB
50Ω
0.1µF
20pF
50Ω
20pF
RSET
Switches
0.1µF
INT/EXT
PD
Latches
+1.24V Ref.
AGND
8-Bit Data Input
D7.......D0
CLK
DGND
DAC908
4
SBAS109B
TIMING DIAGRAM
t2
t1
CLOCK
t S
t H
Data changes
Data changes
Stable, Valid
Data
D13- D0
t PD
t SET
Iout
or
Iout
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
t1
t2
tS
tH
tPD
tSET
Clock Pulse HIGH Time
Clock Pulse LOW Time
Data Setup Time
Data Hold Time
Propagation Delay Time
Output Settling Time to 0.1%
3
3
1.0
1.5
1
ns
ns
ns
ns
ns
ns
30
DAC908
SBAS109B
5
TYPICAL CHARACTERISTICS: VD = VA = +5V
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
SFDR vs fOUT AT 25MSPS
SFDR vs fOUT AT 50MSPS
85
80
75
70
65
60
55
85
80
75
70
65
60
55
–6dBFS
–6dBFS
0dBFS
0dBFS
0
2.0
4.0
6.0
8.0
10.0
12.0
0
5.0
10.0
15.0
20.0
25.0
Frequency (MHz)
Frequency (MHz)
SFDR vs fOUT AT 100MSPS
SFDR vs fOUT AT 125MSPS
85
80
75
70
65
60
55
50
45
85
80
75
70
65
60
55
50
45
–6dBFS
–6dBFS
0dBFS
0dBFS
0
10.0
20.0
30.0
40.0
50.0
0
10.0
20.0
30.0
40.0
50.0
60.0
Frequency (MHz)
Frequency (MHz)
SFDR vs IOUTFS and fOUT AT 100MSPS
SFDR vs fOUT AT 165MSPS
80
75
70
65
60
55
50
45
40
80
75
70
65
60
55
50
45
40
2.1MHz
5.04MHz
–6dBFS
10.1MHz
20.2MHz
0dBFS
40.4MHz
X
X
X
X
2
5
10
20
0
10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0
Frequency (MHz)
I
OUTFS (mA)
DAC908
6
SBAS109B
TYPICAL CHARACTERISTICS: VD = VA = +5V (Cont.)
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
SFDR vs TEMPERATURE AT 100MSPS, 0dBFS
THD vs fCLOCK AT fOUT = 2.1MHz
85
80
75
70
65
60
55
50
45
–70
–75
–80
–85
–90
–95
–100
2HD
2.1MHz
3HD
5.04MHz
X
X
X
X
X
X
X
X
X
20.2MHz
X
X
4HD
–40
–20
0
25
50
70
85
0
25
50
100
125
150
Temperature (°C)
f
CLOCK (MSPS)
SINGLE-TONE OUTPUT SPECTRUM
SINGLE-TONE OUTPUT SPECTRUM
10
0
10
0
fCLOCK = 50MSPS
fOUT = 2.1MHz
fCLOCK = 100MSPS
fOUT = 5.04MHz
–10
–20
–30
–40
–50
–60
–70
–80
–90
–10
–20
–30
–40
–50
–60
–70
–80
–90
SFDR = 69dBc
Amplitude = 0dBFS
SFDR = 67dBc
Amplitude = 0dBFS
0
5
10
15
20
25
0
5
10
15 20
25
30
35
40
45 50
Frequency (MHz)
Frequency (MHz)
SINGLE-TONE OUTPUT SPECTRUM
10
0
fCLOCK = 125MSPS
fOUT = 25.3MHz
–10
–20
–30
–40
–50
–60
–70
–80
–90
SFDR = 57dBc
Amplitude = 0dBFS
0
12.5
25.0
37.5
50.0
62.5
Frequency (MHz)
DAC908
SBAS109B
7
TYPICAL CHARACTERISTICS: VD = VA = +3V
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
SFDR vs fOUT AT 25MSPS
SFDR vs fOUT AT 50MSPS
85
80
75
70
65
60
55
85
80
75
70
65
60
55
–6dBFS
0dBFS
0dBFS
–6dBFS
0
2.0
4.0
6.0
8.0
10.0
12.0
0
5.0
10.0
15.0
20.0
25.0
Frequency (MHz)
Frequency (MHz)
SFDR vs fOUT AT 100MSPS
SFDR vs fOUT AT 125MSPS
85
80
75
70
65
60
55
50
45
85
80
75
70
65
60
55
50
45
–6dBFS
–6dBFS
0dBFS
0dBFS
0
10.0
20.0
30.0
40.0
50.0
0
10.0
20.0
30.0
40.0
50.0
60.0
Frequency (MHz)
Frequency (MHz)
SFDR vs IOUTFS and fOUT AT 100MSPS, 0dBFS
2.1MHz
SFDR vs fOUT AT 165MSPS
80
75
70
65
60
55
50
45
40
80
75
70
65
60
55
50
45
40
5.04MHz
10.1MHz
–6dBFS
20.2MHz
0dBFS
X
X
40.4MHz
X
X
0
10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0
Frequency (MHz)
2
5
10
20
IOUTFS (mA)
DAC908
8
SBAS109B
TYPICAL CHARACTERISTICS: VD = VA = +3V (Cont.)
At TA = +25°C, differential transformer coupled output, 50Ω doubly terminated, and SFDR up to Nyquist, unless otherwise noted.
SFDR vs TEMPERATURE AT 100MSPS, 0dBFS
THD vs fCLOCK AT fOUT = 2.1MHz
85
80
75
70
65
60
55
50
45
–70
–75
–80
–85
–90
–95
–100
2HD
2.1MHz
5.04MHz
X
X
3HD
4HD
X
X
X
X
X
20.2MHz
–40
–20
0
25
50
70
85
0
25
50
100
125
150
Temperature (°C)
f
CLOCK (MSPS)
DAC908
SBAS109B
9
DAC TRANSFER FUNCTION
APPLICATION INFORMATION
THEORY OF OPERATION
The total output current, IOUTFS, of the DAC908 is the
summation of the two complementary output currents:
The architecture of the DAC908 uses the current steering
technique to enable fast switching and a high update rate. The
core element within the monolithic DAC is an array of
segmented current sources that are designed to deliver a full-
scale output current of up to 20mA, as shown in Figure 1. An
internal decoder addresses the differential current switches
each time the DAC is updated and a corresponding output
current is formed by steering all currents to either output
summing node, IOUT or IOUT. The complementary outputs
deliver a differential output signal that improves the dynamic
performance through reduction of even-order harmonics,
common-mode signals (noise), and double the peak-to-peak
output signal swing by a factor of two, compared to single-
ended operation.
IOUTFS = IOUT + IOUT
(1)
The individual output currents depend on the DAC code and
can be expressed as:
IOUT = IOUTFS • (Code/256)
(2)
(3)
IOUT = IOUTFS • (255 – Code/256)
where ‘Code’ is the decimal representation of the DAC data
input word. Additionally, IOUTFS is a function of the refer-
ence current IREF, which is determined by the reference
The segmented architecture results in a significant reduc-
tion of the glitch energy, and improves the dynamic perfor-
mance (SFDR) and DNL. The current outputs maintain a
very high output impedance of greater than 200kΩ.
voltage and the external setting resistor, RSET
.
IOUTFS = 32 • IREF = 32 • VREF/RSET
(4)
The full-scale output current is determined by the ratio of
the internal reference voltage (1.24V) and an external
resistor, RSET. The resulting IREF is internally multiplied by
a factor of 32 to produce an effective DAC output current
that can range from 2mA to 20mA, depending on the value
In most cases the complementary outputs will drive resistive
loads or a terminated transformer. A signal voltage will
develop at each output according to:
of RSET
.
VOUT = IOUT • RLOAD
VOUT = IOUT • RLOAD
(5)
(6)
The DAC908 is split into a digital and an analog portion,
each of which is powered through its own supply pin. The
digital section includes edge-triggered input latches and the
decoder logic, while the analog section comprises the cur-
rent source array with its associated switches and the
reference circuitry.
+3V to +5V
Digital
+3V to +5V
Analog
0.1µF
Bandwidth
Control
BW
+VA
+VD
DAC908
Full-Scale
Adjust
Resistor
IOUT
IOUT
1:1
VOUT
LSB
Switches
FSA
PMOS
Current
Source
Array
Ref
Control
Amp
Ref
Input REFIN
Segmented
MSB
Switches
50Ω
400pF
RSET
2kΩ
20pF
50Ω
20pF
0.1µF
0.1µF
BYP
INT/EXT
Ref
Buffer
Latches and Switch
Decoder Logic
PD
Power Down
(internal pull-down)
+1.24V Ref
8-Bit Data Input
D7...D0
AGND
Analog
CLK
DGND
Clock
Input
Digital
Ground
Ground
NOTE: Supply bypassing not shown.
FIGURE 1. Functional Block Diagram of the DAC908.
10
DAC908
SBAS109B
The value of the load resistance is limited by the output
compliance specification of the DAC908. To maintain speci-
fied linearity performance, the voltage for IOUT and IOUT
should not exceed the maximum allowable compliance range.
IOUT and IOUT. Furthermore, using the differential output
configuration in combination with a transformer will be
instrumental for achieving excellent distortion performance.
Common-mode errors, such as even-order harmonics or
noise, can be substantially reduced. This is particularly the
case with high output frequencies and/or output amplitudes
below full-scale.
The two single-ended output voltages can be combined to
find the total differential output swing:
(2 • Code – 255)
For those applications requiring the optimum distortion and
noise performance, it is recommended to select a full-scale
output of 20mA. A lower full-scale range down to 2mA may
be considered for applications that require a low power
consumption, but can tolerate a reduced performance level.
VOUTDIFF = VOUT – VOUT
=
• IOUTFS • RLOAD
(7)
256
ANALOG OUTPUTS
The DAC908 provides two complementary current outputs,
IOUT and IOUT. The simplified circuit of the analog output
stage representing the differential topology is shown in
Figure 2. The output impedance of 200kΩ || 12pF for IOUT
and IOUT results from the parallel combination of the differ-
ential switches, along with the current sources and associ-
ated parasitic capacitances.
INPUT CODE (D7 - D0)
IOUT
IOUT
1111 1111
1000 0000
0000 0000
20mA
10mA
0mA
0mA
10mA
20mA
TABLE I. Input Coding vs Analog Output Current.
OUTPUT CONFIGURATIONS
The current output of the DAC908 allows for a variety of
configurations, some of which are illustrated below. As
mentioned previously, utilizing the converter’s differential
outputs will yield the best dynamic performance. Such a
differential output circuit may consist of an RF transformer
(see Figure 3) or a differential amplifier configuration (see
Figure 4). The transformer configuration is ideal for most
applications with ac coupling, while op amps will be suitable
for a DC-coupled configuration.
+VA
DAC908
The single-ended configuration (see Figure 6) may be consid-
ered for applications requiring a unipolar output voltage.
Connecting a resistor from either one of the outputs to ground
will convert the output current into a ground-referenced volt-
age signal. To improve on the DC linearity an I-to-V converter
can be used instead. This will result in a negative signal
excursion and, therefore, requires a dual supply amplifier.
IOUT
RL
IOUT
RL
FIGURE 2. Equivalent Analog Output.
DIFFERENTIAL WITH TRANSFORMER
The signal voltage swing that may develop at the two
outputs, IOUT and IOUT, is limited by a negative and positive
compliance. The negative limit of –1V is given by the
breakdown voltage of the CMOS process, and exceeding it
will compromise the reliability of the DAC908, or even
cause permanent damage. With the full-scale output set to
20mA, the positive compliance equals 1.25V, operating with
+VD = 5V. Note that the compliance range decreases to
about 1V for a selected output current of IOUTFS = 2mA.
Care should be taken that the configuration of DAC908 does
not exceed the compliance range to avoid degradation of the
distortion performance and integral linearity.
Using an RF transformer provides a convenient way of
converting the differential output signal into a single-ended
signal while achieving excellent dynamic performance (see
Figure 3). The appropriate transformer should be carefully
selected based on the output frequency spectrum and imped-
ance requirements. The differential transformer configura-
tion has the benefit of significantly reducing common-mode
signals, thus improving the dynamic performance over a
wide range of frequencies. Furthermore, by selecting a
suitable impedance ratio (winding ratio), the transformer can
be used to provide optimum impedance matching while
controlling the compliance voltage for the converter outputs.
The model shown in Figure 3 has a 1:1 ratio and may be used
to interface the DAC908 to a 50Ω load. This results in a 25Ω
load for each of the outputs, IOUT and IOUT. The output
signals are ac coupled and inherently isolated because of the
transformer's magnetic coupling.
Best distortion performance is typically achieved with the
maximum full-scale output signal limited to approximately
0.5V. This is the case for a 50Ω doubly-terminated load and
a 20mA full-scale output current. A variety of loads can be
adapted to the output of the DAC908 by selecting a suitable
transformer while maintaining optimum voltage levels at
DAC908
SBAS109B
11
As shown in Figure 3, the transformer’s center tap must be
connected to ground to enable the necessary DC-current
flow for both outputs. Some applications may require a solid
termination, in which case a differential resistor, RDIFF, may
be inserted as shown. Note that this will reduce the available
signal power by approximately one half.
of the resistors typically sets the limit for the achievable
common-mode rejection. An improvement can be obtained
by fine tuning resistor R4.
This configuration typically delivers a lower level of ac
performance than the previously discussed transformer solu-
tion because the amplifier introduces another source of
distortion. Suitable amplifiers should be selected based on
their slew-rate, harmonic distortion, and output swing capa-
bilities. High-speed amplifiers like the OPA680 or OPA687
may be considered. The ac performance of this circuit may
be improved by adding a small capacitor, CDIFF, between the
ADT1-1WT
(Mini-Circuits)
1:1
IOUT
outputs IOUT and IOUT, as shown in Figure 4. This will intro-
50Ω
Optional
RDIFF
DAC908
RL
duce a real pole to create a low-pass filter in order to slew-
limit the DACs fast output signal steps, which otherwise
could drive the amplifier into slew-limitations or into an
overload condition; both would cause excessive distortion.
The difference amplifier can easily be modified to add a
level shift for applications requiring the single-ended output
voltage to be unipolar, i.e., swing between 0V and +2V.
IOUT
50Ω
FIGURE 3. Differential Output Configuration Using an RF
Transformer.
DUAL TRANSIMPEDANCE OUTPUT CONFIGURATION
The circuit example of Figure 5 shows the signal output
currents connected into the summing junction of the
OPA2680, which is set up as a transimpedance stage, or
I-to-V converter. With this circuit, the DAC’s output will be
kept at a virtual ground, minimizing the effects of output
impedance variations, and resulting in the best DC linearity
(INL). However, as mentioned previously, the amplifier
may be driven into slew-rate limitations, and produce un-
wanted distortion. This may occur especially at high DAC
update rates.
DIFFERENTIAL CONFIGURATION USING AN OP AMP
If the application requires a DC-coupled output, a difference
amplifier may be considered, as shown in Figure 4. Four
external resistors are needed to configure the voltage-feed-
back op amp OPA680 as a difference amplifier performing
the differential to single-ended conversion. Under the shown
configuration, the DAC908 generates a differential output
signal of 0.5Vp-p at the load resistors, RL. The resistor
values shown were selected to result in a symmetric 25Ω
loading for each of the current outputs since the input
impedance of the difference amplifier is in parallel to resis-
tors RL, and should be considered.
+5V
50Ω
1/2
OPA2680
–VOUT = IOUT • RF
R2
402Ω
RF1
CF1
DAC908
R1
200Ω
IOUT
IOUT
CD1
VOUT
DAC908
IOUT
OPA680
R3
200Ω
CDIFF
RF2
CF2
–5V +5V
RL
28.7Ω
R4
402Ω
RL
26.1Ω
CD2
IOUT
1/2
OPA2680
–VOUT = IOUT • RF
FIGURE 4. Difference Amplifier Provides Differential to
Single-Ended Conversion and DC-Coupling.
50Ω
–5V
The OPA680 is configured for a gain of two. Therefore,
operating the DAC908 with a 20mA full-scale output will
produce a voltage output of ±1V. This requires the amplifier
to operate off of a dual power supply (±5V). The tolerance
FIGURE 5. Dual, Voltage-Feedback Amplifier OPA2680
Forms Differential Transimpedance Amplifier.
DAC908
12
SBAS109B
INTERNAL REFERENCE OPERATION
The DC gain for this circuit is equal to feedback resistor RF.
At high frequencies, the DAC output impedance (CD1, CD2)
will produce a zero in the noise gain for the OPA2680 that
may cause peaking in the closed-loop frequency response.
CF is added across RF to compensate for this noise-gain
peaking. To achieve a flat transimpedance frequency re-
sponse, the pole in each feedback network should be set to:
The DAC908 has an on-chip reference circuit that comprises
a 1.24V bandgap reference and a control amplifier. Ground-
ing pin 16, INT/EXT, enables the internal reference opera-
tion. The full-scale output current, IOUTFS, of the DAC908 is
determined by the reference voltage, VREF, and the value of
resistor RSET. IOUTFS can be calculated by:
IOUTFS = 32 • IREF = 32 • VREF / RSET
(10)
1
GBP
=
(8)
2πRFCF 4πRFCD
As shown in Figure 7, the external resistor RSET connects to
the FSA pin (Full-Scale Adjust). The reference control am-
plifier operates as a V-to-I converter producing a reference
current, IREF, which is determined by the ratio of VREF and
RSET, as shown in Equation 10. The full-scale output current,
IOUTFS, results from multiplying IREF by a fixed factor of 32.
with GBP = Gain Bandwidth Product of OPA
which will give a corner frequency f-3dB of approximately:
GBP
f−3dB
=
(9)
2πRFCD
+5V
CCOMPEXT
0.1µF
The full-scale output voltage is defined by the product of
IOUTFS • RF, and has a negative unipolar excursion. To
improve on the ac performance of this circuit, adjustment of
RF and/or IOUTFS should be considered. Further extensions of
this application example may include adding a differential
filter at the OPA2680’s output followed by a transformer, in
order to convert to a single-ended signal.
BW
+VA
DAC908
VREF
RSET
IREF
=
FSA
Ref
Control
Amp
Current
Sources
REFIN
RSET
2kΩ
SINGLE-ENDED CONFIGURATION
CCOMP
400pF
0.1µF
Using a single load resistor connected to the one of the DAC
outputs, a simple current-to-voltage conversion can be ac-
complished. The circuit in Figure 6 shows a 50Ω resistor
connected to IOUT, providing the termination of the further
connected 50Ω cable. Therefore, with a nominal output
current of 20mA, the DAC produces a total signal swing of
0V to 0.5V into the 25Ω load.
INT/EXT
+1.24V Ref.
FIGURE 7. Internal Reference Configuration.
Using the internal reference, a 2kΩ resistor value results in a
20mA full-scale output. Resistors with a tolerance of 1% or
better should be considered. Selecting higher values, the con-
verter output can be adjusted from 20mA down to 2mA.
Operating the DAC908 at lower than 20mA output currents
may be desirable for reasons of reducing the total power
consumption, improving the distortion performance, or observ-
ing the output compliance voltage limitations for a given load
condition.
IOUTFS = 20mA
VOUT = 0V to +0.5V
IOUT
DAC908
IOUT
50Ω
50Ω
25Ω
It is recommended to bypass the REFIN pin with a ceramic chip
capacitor of 0.1µF or more. The control amplifier is internally
compensated, and its small signal bandwidth is approximately
1.3MHz. To improve the ac performance, an additional capaci-
tor (CCOMPEXT) should be applied between the BW pin and the
analog supply, +VA, as shown in Figure 7. Using a 0.1µF
capacitor, the small-signal bandwidth and output impedance of
the control amplifier is further diminished, reducing the noise
that is fed into the current source array. This also helps shunting
feedthrough signals more effectively, and improving the noise
performance of the DAC908.
FIGURE 6. Driving a Doubly-Terminated 50Ω Cable Directly.
Different load resistor values may be selected as long as the
output compliance range is not exceeded. Additionally, the
output current, IOUTFS, and the load resistor may be mutually
adjusted to provide the desired output signal swing and
performance.
DAC908
SBAS109B
13
EXTERNAL REFERENCE OPERATION
POWER-DOWN MODE
The DAC908 features a power-down function which can be
used to reduce the supply current to less than 9mA over the
specified supply range of 2.7V to 5.5V. Applying a logic
High to the PD pin will initiate the power-down mode, while
a logic Low enables normal operation. When left uncon-
nected, an internal active pull-down circuit will enable the
normal operation of the converter.
The internal reference can be disabled by applying a logic
HIGH (+VA) to pin INT/EXT. An external reference voltage
can then be driven into the REFIN pin, which in this case
functions as an input, as shown in Figure 8. The use of an
external reference may be considered for applications that
require higher accuracy and drift performance, or to add the
ability of dynamic gain control.
While a 0.1µF capacitor is recommended to be used with the
internal reference, it is optional for the external reference
operation. The reference input, REFIN, has a high input
impedance (1MΩ) and can easily be driven by various
sources. Note that the voltage range of the external reference
should stay within the compliance range of the reference
input (0.1V to 1.25V).
GROUNDING, DECOUPLING AND
LAYOUT INFORMATION
Proper grounding and bypassing, short lead length, and the
use of ground planes are particularly important for high
frequency designs. Multilayer pc-boards are recommended
for best performance since they offer distinct advantages
such as minimization of ground impedance, separation of
signal layers by ground layers, etc.
DIGITAL INPUTS
The DAC908 uses separate pins for its analog and digital
supply and ground connections. The placement of the decou-
pling capacitor should be such that the analog supply (+VA)
is bypassed to the analog ground (AGND), and the digital
supply bypassed to the digital ground (DGND). In most
cases 0.1uF ceramic chip capacitors at each supply pin are
adequate to provide a low impedance decoupling path. Keep
in mind that their effectiveness largely depends on the
proximity to the individual supply and ground pins. There-
fore, they should be located as close as physically possible
to those device leads. Whenever possible, the capacitors
should be located immediately under each pair of supply/
ground pins on the reverse side of the pc-board. This layout
approach will minimize the parasitic inductance of compo-
nent leads and pcb runs.
The digital inputs, D0 (LSB) through D7 (MSB) of the
DAC908 accepts standard-positive binary coding. The digi-
tal input word is latched into a master-slave latch with the
rising edge of the clock. The DAC output becomes updated
with the following falling clock edge (refer to the specifica-
tion table and timing diagram for details). The best perfor-
mance will be achieved with a 50% clock duty cycle,
however, the duty cycle may vary as long as the timing
specifications are met. Additionally, the setup and hold
times may be chosen within their specified limits.
All digital inputs are CMOS compatible. The logic thresh-
olds depend on the applied digital supply voltage such that
they are set to approximately half the supply voltage;
Vth = +VD/2 (±20% tolerance). The DAC908 is designed to
operate over a supply range of 2.7V to 5.5V.
+5V
CCOMPEXT
0.1µF
BW
+VA
DAC908
VREF
RSET
IREF
=
FSA
Ref
Control
Amp
Current
Sources
REFIN
External
Reference
CCOMP
400pF
INT/EXT
RSET
+5V
+1.24V Ref.
FIGURE 8. External Reference Configuration.
DAC908
14
SBAS109B
Further supply decoupling with surface mount tantalum
capacitors (1uF to 4.7uF) may be added as needed in
proximity of the converter.
The power to the DAC908 should be provided through the
use of wide pcb runs or planes. Wide runs will present a
lower trace impedance, further optimizing the supply decou-
pling. The analog and digital supplies for the converter
should only be connected together at the supply connector of
the pc-board. In the case of only one supply voltage being
available to power the DAC, ferrite beads along with bypass
capacitors may be used to create an LC filter. This will
generate a low-noise analog supply voltage that can then be
connected to the +VA supply pin of the DAC908.
Low noise is required for all supply and ground connections
to the DAC908. It is recommended to use a multilayer pc-
board utilizing separate power and ground planes. Mixed
signal designs require particular attention to the routing of
the different supply currents and signal traces. Generally,
analog supply and ground planes should only extend into
analog signal areas, such as the DAC output signal and the
reference signal. Digital supply and ground planes must be
confined to areas covering digital circuitry, including the
digital input lines connecting to the converter, as well as the
clock signal. The analog and digital ground planes should be
joined together at one point underneath the DAC. This can
be realized with a short track of approximately 1/8" (3mm).
While designing the layout, it is important to keep the analog
signal traces separate from any digital line, in order to
prevent noise coupling onto the analog signal path.
DAC908
SBAS109B
15
PACKAGE OPTION ADDENDUM
www.ti.com
21-May-2010
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
DAC908E
DAC908E/2K5
DAC908E/2K5G4
DAC908EG4
DAC908U
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
TSSOP
TSSOP
TSSOP
TSSOP
SOIC
PW
PW
PW
PW
DW
DW
DW
DW
28
28
28
28
28
28
28
28
50
2500
2500
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
20
Green (RoHS
& no Sb/Br)
DAC908U/1K
DAC908U/1KG4
DAC908UG4
SOIC
1000
1000
20
Green (RoHS
& no Sb/Br)
SOIC
Green (RoHS
& no Sb/Br)
SOIC
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
21-May-2010
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
DAC908E/2K5
DAC908U/1K
TSSOP
SOIC
PW
DW
28
28
2500
1000
330.0
330.0
16.4
32.4
6.9
10.2
1.8
3.1
12.0
16.0
16.0
32.0
Q1
Q1
11.35 18.67
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
DAC908E/2K5
DAC908U/1K
TSSOP
SOIC
PW
DW
28
28
2500
1000
367.0
367.0
367.0
367.0
38.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明