DLP9000XUVFLS [TI]
DLP® 0.90 高速 WQXGA UV A 型 DMD | FLS | 355 | 20 to 30;
| 型号： | DLP9000XUVFLS |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | DLP® 0.90 高速 WQXGA UV A 型 DMD | FLS | 355 | 20 to 30 商用集成电路 |
| 文件： | 总54页 (文件大小：2533K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DLP9000XUV
DLPS158 –DECEMBER 2019
DLP9000XUV 0.9 UV WQXGA Type A DMD
1 Features
–
–
–
Laser marking and repair systems
Computer to plate printers
3D printers
1
•
High resolution 2560 × 1600 (WQXGA) Array
–
–
–
–
–
–
> 4 Million micromirrors
•
Medical
7.56-µm micromirror pitch
–
–
Ophthalmology
Photo therapy
0.9-Inch micromirror array diagonal
±12° micromirror tilt angle
Designed for corner illumination
Integrated micromirror driver circuitry
3 Description
Featuring over
4
million micromirrors, the
•
•
DLP9000XUV with the DLPC910 controller
DLP9000XUV digital micromirror device (DMD)
enables high resolution and high performance spatial
light modulation of UV wavelengths from 355 nm to
420 nm. The DLP9000XUV is designed with a special
UV optimized window to support numerous
applications in the industrial and medical markets.
Reliable operation of the DLP9000XUV chipset
requires the DMD be driven by the DLPC910
Controller. The DLP9000XUV chipset's architecture
enables continuous data streaming for very high
speed lithographic applications. The 4.1 megapixel
resolution of the DMD enables large 3D print build
sizes and results in fine detail for Digital Lithography.
–
–
–
–
480-MHz input data clock rate
Streams up to 61 gigapixels per second
1-Bit binary patterns up to 14,989 Hz
8-Bit gray patterns up to 1,873 Hz (coupled
with Illumination Modulation)
Designed to steer UV wavelengths from 355 to
420 nm
–
–
–
–
Window transmission 98% (per window pass)
Micromirror reflectivity 88% (nominal)
Array diffraction efficiency 85% (nominal)
Array fill factor 92% (nominal)
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
2 Applications
42.20 mm x 42.20 mm x
7.00 mm
DLP9000XUV
FLS (355)
•
Industrial
Direct imaging lithography
–
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Application Schematic
Illumination
Driver
Illumination
Sensor
LVDS Interface
DCLKIN (A,B,C,D), DVALID (A,B,C,D), DIN(A,B,C,D)
Row and Block Signals
ROWMD (1:0), ROWAD (10:0), BLKMD (1:0), BLKAD (3:0), RST2BLKZ
USER
Interface
DOUT(A,B,C,D)[15:0]
DCLKOUT (A,B,C,D)
APPS
FPGA
Control Signals
COMP_DATA.NS_FLIP,WDT_ENBLZ,PWR_FLOAT
SCTRL (A,B,C,D)
Status Signals
RST_ACTIVE, INIT_ACTIVE, ECP2_FINISHED
Connectivity
USB
Ethernet
RESET_ADDR (3:0)
RESET_MODE (1:0)
RESET_SEL (1:0)
JTAG(3:0)
DLP9000XUV
DLPC910
RESET_STRB
RESET_OEZ
Volatile
And
PGM(4:0)
DLPR910
Non-Volatile
Storage
RESET_IRQZ
CTRL_RSTZ
I2C
SCP BUS (3:0)
RESETZ
VLED0
VLED1
OSC
50 MHz
Power Management
Power In
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
Table of Contents
8.5 Window Characteristics and Optics ....................... 29
8.6 Micromirror Array Temperature Calculation............ 30
8.7 Micromirror Landed-On/Landed-Off Duty Cycle ..... 31
Application and Implementation ........................ 33
9.1 Application Information............................................ 33
9.2 Typical Applications ................................................ 34
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications....................................................... 10
6.1 Absolute Maximum Ratings .................................... 10
6.2 Storage Conditions.................................................. 10
6.3 ESD Ratings............................................................ 11
6.4 Recommended Operating Conditions..................... 11
6.5 Thermal Information................................................ 13
6.6 Electrical Characteristics......................................... 13
6.7 Timing Requirements.............................................. 14
9
10 Power Supply Requirements ............................. 36
10.1 DMD Power Supply Requirements ...................... 36
10.2 DMD Power Supply Power-Up Procedure ........... 36
10.3 DMD Mirror Park Sequence (Power_Float)
Requirements........................................................... 37
10.4 DMD Power Supply Power-Down Procedure ...... 37
11 Layout................................................................... 40
11.1 Layout Guidelines ................................................. 40
11.2 Layout Example .................................................... 42
12 Device and Documentation Support ................. 45
12.1 Device Support...................................................... 45
12.2 Documentation Support ........................................ 46
12.3 Support Resources ............................................... 46
12.4 Trademarks........................................................... 46
12.5 Electrostatic Discharge Caution............................ 46
12.6 Glossary................................................................ 46
6.8 Capacitance at Recommended Operating
Conditions ................................................................ 18
6.9 Typical Characteristics............................................ 18
6.10 System Mounting Interface Loads ........................ 19
6.11 Micromirror Array Physical Characteristics........... 20
6.12 Micromirror Array Optical Characteristics ............. 21
6.13 Optical and System Image Quality........................ 22
6.14 Window Characteristics......................................... 22
6.15 Chipset Component Usage Specification ............. 22
Parameter Measurement Information ................ 23
Detailed Description ............................................ 24
8.1 Overview ................................................................. 24
8.2 Functional Block Diagram ....................................... 25
8.3 Feature Description................................................. 26
8.4 Device Functional Modes........................................ 29
13 Mechanical, Packaging, and Orderable
7
8
Information ........................................................... 46
13.1 Thermal Characteristics ........................................ 46
13.2 Package Thermal Resistance ............................... 46
13.3 Case Temperature ................................................ 46
13.4 Package Option Addendum .................................. 47
4 Revision History
DATE
REVISION
NOTES
December 2019
*
Initial Release.
2
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
5 Pin Configuration and Functions
FLS Package Connector Terminals
355-Pin CLGA
Bottom View
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
TRACE
Pin Functions
(1)
PIN
TYPE
(I/O/P)
DATA
INTERNAL
SIGNAL
DESCRIPTION
(2)
(3)
(4)
RATE
TERM
(mils)
NAME
NO.
DATA BUS A
D_AN(0)
D_AN(1)
D_AN(2)
D_AN(3)
D_AN(4)
D_AN(5)
D_AN(6)
D_AN(7)
D_AN(8)
D_AN(9)
D_AN(10)
D_AN(11)
D_AN(12)
D_AN(13)
D_AN(14)
D_AN(15)
D_AP(0)
D_AP(1)
D_AP(2)
D_AP(3)
D_AP(4)
D_AP(5)
D_AP(6)
D_AP(7)
D_AP(8)
D_AP(9)
D_AP(10)
D_AP(11)
D_AP(12)
D_AP(13)
D_AP(14)
D_AP(15)
DATA BUS B
D_BN(0)
D_BN(1)
D_BN(2)
D_BN(3)
D_BN(4)
D_BN(5)
D_BN(6)
D_BN(7)
H10
G3
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
737
737
737
738
739
739
737
737
739
736
743
737
739
740
737
737
737
738
737
736
739
738
737
737
739
737
741
737
739
739
737
737
G9
F4
F10
E3
E9
D2
J5
C9
F14
B8
G15
B14
H16
D16
H8
G5
G11
F2
F8
E5
E11
D4
J3
C11
F16
B10
H14
B16
G17
D14
AD8
AE3
AF8
AF2
AG5
AH8
AG9
AH2
Input
Input
Input
Input
Input
Input
Input
Input
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
739
737
736
739
737
737
737
739
(1) The following power supplies are required to operate the DMD: VCC, VCCI, VOFFSET, VBIAS, and VRESET. VSS must also be connected.
(2) DDR = Double data rate.
SDR = Single data rate.
Refer to the Timing Requirements regarding specifications and relationships.
(3) Internal term = CMOS level internal termination. Refer to Recommended Operating Conditions regarding differential termination
specification.
(4) Dielectric constant for the DMD type A ceramic package is approximately 9.6.
For the package trace lengths shown:
Propagation speed = 11.8 / sqrt(9.6) = 3.808 in/ns.
Propagation delay = 0.262 ns/in = 262 ps/in = 10.315 ps/mm.
4
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Pin Functions (continued)
(1)
PIN
TYPE
(I/O/P)
DATA
RATE
INTERNAL
TERM
TRACE
(mils)
SIGNAL
DESCRIPTION
(2)
(3)
(4)
NAME
NO.
AL9
D_BN(8)
D_BN(9)
D_BN(10)
D_BN(11)
D_BN(12)
D_BN(13)
D_BN(14)
D_BN(15)
D_BP(0)
D_BP(1)
D_BP(2)
D_BP(3)
D_BP(4)
D_BP(5)
D_BP(6)
D_BP(7)
D_BP(8)
D_BP(9)
D_BP(10)
D_BP(11)
D_BP(12)
D_BP(13)
D_BP(14)
D_BP(15)
DATA BUS C
D_CN(0)
D_CN(1)
D_CN(2)
D_CN(3)
D_CN(4)
D_CN(5)
D_CN(6)
D_CN(7)
D_CN(8)
D_CN(9)
D_CN(10)
D_CN(11)
D_CN(12)
D_CN(13)
D_CN(14)
D_CN(15)
D_CP(0)
D_CP(1)
D_CP(2)
D_CP(3)
D_CP(4)
D_CP(5)
D_CP(6)
D_CP(7)
D_CP(8)
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
737
738
736
737
740
737
738
738
738
737
737
738
737
737
737
740
736
739
737
737
737
737
740
739
AJ11
AF14
AE11
AH16
AD14
AG17
AD16
AD10
AE5
AF10
AF4
AG3
AH10
AG11
AH4
AL11
AJ9
AF16
AE9
AH14
AE15
AG15
AE17
C15
E15
A17
F20
B20
G21
D22
E23
B26
F28
C27
J29
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
737
737
736
737
738
737
737
737
739
737
737
737
737
739
736
737
738
737
735
737
737
737
737
737
739
D26
H26
E29
G29
C17
E17
A15
F22
B22
H20
D20
E21
B28
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
TRACE
Pin Functions (continued)
(1)
PIN
TYPE
(I/O/P)
DATA
INTERNAL
SIGNAL
DESCRIPTION
(2)
(3)
(4)
RATE
TERM
(mils)
NAME
NO.
D_CP(9)
F26
C29
J27
Input
Input
Input
Input
Input
Input
Input
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
DDR
DDR
DDR
DDR
DDR
DDR
DDR
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
735
737
737
736
739
736
737
D_CP(10)
D_CP(11)
D_CP(12)
D_CP(13)
D_CP(14)
D_CP(15)
DATA BUS D
D_DN(0)
D28
H28
E27
G27
AJ15
AC27
AK16
AE29
AE21
AF20
AL15
AG29
AD22
AG21
AJ23
AJ29
AF28
AK22
AD28
AK28
AJ17
AC29
AK14
AE27
AD20
AF22
AL17
AG27
AE23
AG23
AJ21
AJ27
AF26
AK20
AD26
AK26
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, negative
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
Differential Data, positive
737
737
738
738
737
738
737
738
739
738
736
737
737
741
739
739
737
737
738
737
737
738
737
738
739
738
736
737
737
740
739
739
D_DN(1)
D_DN(2)
D_DN(3)
D_DN(4)
D_DN(5)
D_DN(6)
D_DN(7)
D_DN(8)
D_DN(9)
D_DN(10)
D_DN(11)
D_DN(12)
D_DN(13)
D_DN(14)
D_DN(15)
D_DP(0)
D_DP(1)
D_DP(2)
D_DP(3)
D_DP(4)
D_DP(5)
D_DP(6)
D_DP(7)
D_DP(8)
D_DP(9)
D_DP(10)
D_DP(11)
D_DP(12)
D_DP(13)
D_DP(14)
D_DP(15)
SERIAL CONTROL
SCTRL_AN
SCTRL_BN
SCTRL_CN
SCTRL_DN
SCTRL_AP
SCTRL_BP
SCTRL_CP
SCTRL_DP
D8
Input
Input
Input
Input
Input
Input
Input
Input
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
DDR
DDR
DDR
DDR
DDR
DDR
DDR
DDR
Differential Serial control, negative
Differential Serial control, negative
Differential Serial control, negative
Differential Serial control, negative
Differential Serial control, positive
Differential Serial control, positive
Differential Serial control, positive
Differential Serial control, positive
736
739
737
739
736
739
739
739
AK8
G23
AH28
D10
AK10
H22
AH26
6
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Pin Functions (continued)
(1)
PIN
TYPE
(I/O/P)
DATA
RATE
INTERNAL
TERM
TRACE
(mils)
SIGNAL
DESCRIPTION
(2)
(3)
(4)
NAME
NO.
CLOCKS
DCLK_AN
DCLK_BN
DCLK_CN
DCLK_DN
DCLK_AP
DCLK_BP
DCLK_CP
DCLK_DP
H2
AJ5
Input
Input
Input
Input
Input
Input
Input
Input
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
LVDS
Differential Clock, negative
Differential Clock, negative
Differential Clock, negative
Differential Clock, negative
Differential Clock, positive
Differential Clock, positive
Differential Clock, positive
Differential Clock, positive
740
740
736
736
740
740
736
738
C23
AH22
H4
AJ3
C21
AH20
SERIAL COMMUNICATIONS PORT (SCP)
SCP_DO
SCP_DI
AC3
AD2
AE1
AD4
Output
Input
Input
Input
LVCMOS
LVCMOS
LVCMOS
LVCMOS
SDR
SDR
Serial communications port output
Pull-Down Serial communications port data input
Pull-Down Serial communications port clock
SCP_CLK
SCP_ENZ
Pull-Down Active-low serial communications port enable
MICROMIRROR RESET CONTROL
RESET_ADDR(0)
RESET_ADDR(1)
RESET_ADDR(2)
RESET_ADDR(3)
RESET_MODE(0)
RESET_MODE(1)
RESET_SEL(0)
H12
C5
Input
Input
Input
Input
Input
Input
Input
Input
Input
LVCMOS
LVCMOS
LVCMOS
LVCMOS
LVCMOS
LVCMOS
LVCMOS
LVCMOS
LVCMOS
Pull-Down Reset driver address select
Pull-Down Reset driver address select
Pull-Down Reset driver address select
Pull-Down Reset driver address select
Pull-Down Reset driver mode select
Pull-Down Reset driver mode select
Pull-Down Reset driver level select
Pull-Down Reset driver level select
B6
A19
J1
G1
AK4
AL13
H6
RESET_SEL(1)
RESET_STROBE
Pull-Down Reset address, mode, and level latched on
rising-edge
ENABLES AND INTERRUPTS
PWRDNZ
B4
Input
Input
LVCMOS
LVCMOS
Active-low device reset
RESET_OEZ
AK24
Pull-Down Active-low output enable for DMD reset
driver circuits
RESETZ
AL19
Input
LVCMOS
LVCMOS
Pull-Down Active-low sets reset circuits in known
VOFFSET state
RESET_IRQZ
C3
Output
Active-low, output interrupt to ASIC
VOLTAGE REGULATOR MONITORING
PG_BIAS
J19
Input
Input
LVCMOS
LVCMOS
Pull-Up
Pull-Up
Active-low fault from external VBIAS regulator
PG_OFFSET
A13
Active-low fault from external VOFFSET
regulator
PG_RESET
EN_BIAS
AC19
J15
Input
LVCMOS
LVCMOS
LVCMOS
LVCMOS
Pull-Up
Active-low fault from external VRESET
regulator
Output
Output
Output
Active-high enable for external VBIAS
regulator
EN_OFFSET
EN_RESET
H30
J17
Active-high enable for external VOFFSET
regulator
Active-high enable for external VRESET
regulator
LEAVE PIN UNCONNECTED
MBRST(0)
MBRST(1)
MBRST(2)
MBRST(3)
MBRST(4)
MBRST(5)
MBRST(6)
MBRST(7)
L5
M28
P4
Output
Output
Output
Output
Output
Output
Output
Output
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
P30
L3
P28
P2
T28
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
TRACE
Pin Functions (continued)
(1)
PIN
TYPE
(I/O/P)
DATA
INTERNAL
SIGNAL
DESCRIPTION
(2)
(3)
(4)
RATE
TERM
(mils)
NAME
NO.
MBRST(8)
MBRST(9)
MBRST(10)
MBRST(11)
MBRST(12)
MBRST(13)
MBRST(14)
MBRST(15)
MBRST(16)
MBRST(17)
MBRST(18)
MBRST(19)
MBRST(20)
MBRST(21)
MBRST(22)
MBRST(23)
MBRST(24)
MBRST(25)
MBRST(26)
MBRST(27)
MBRST(28)
MBRST(29)
MBRST(30)
MBRST(31)
M4
L29
T4
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Output
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
N29
N3
L27
R3
V28
V4
R29
Y4
AA27
W3
W27
AA3
W29
U5
U29
Y2
AA29
U3
Y30
AA5
R27
LEAVE PIN UNCONNECTED
RESERVED_PFE
RESERVED_TM
RESERVED_XI0
RESERVED_XI1
RESERVED_XI2
RESERVED_TP0
RESERVED_TP1
RESERVED_TP2
J11
Input
Input
Input
Input
Input
Input
Input
Input
LVCMOS
LVCMOS
LVCMOS
LVCMOS
LVCMOS
Analog
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
Pull-Down For proper DMD operation, do not connect
For proper DMD operation, do not connect
AC7
AC25
AC23
J23
AC9
AC11
AC13
Analog
For proper DMD operation, do not connect
Analog
For proper DMD operation, do not connect
LEAVE PIN UNCONNECTED
RESERVED_BA
RESERVED_BB
RESERVED_BC
RESERVED_BD
RESERVED_TS
AC15
Output
Output
Output
Output
Output
LVCMOS
LVCMOS
LVCMOS
LVCMOS
LVCMOS
For proper DMD operation, do not connect
For proper DMD operation, do not connect
For proper DMD operation, do not connect
For proper DMD operation, do not connect
For proper DMD operation, do not connect
J13
AC21
J21
AC17
LEAVE PIN UNCONNECTED
NO CONNECT
NO CONNECT
NO CONNECT
J7
J9
For proper DMD operation, do not connect
For proper DMD operation, do not connect
For proper DMD operation, do not connect
J25
8
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Pin Functions
PIN
TYPE
(I/O/P)
SIGNAL
DESCRIPTION
(1)
NAME
NO.
Supply voltage for positive bias level of micromirror reset
signal.
VBIAS
A3, A9, A5, A11, A7, B2
L1, N1, R1
Power
Power
Power
Power
Power
Analog
Analog
Analog
Analog
Analog
Supply voltage for HVCMOS logic.
Supply voltage for stepped high voltage at micromirror
address electrodes.
VOFFSET
U1, W1
AC1, AA1
Supply voltage for offset level of MBRST(31:0).
L31, N31, R31, U31, W31,
AA31
Supply voltage for negative reset level of micromirror reset
signal.
VRESET
A21, A23, A25, A27, A29,
C1, C31, E31, G31, J31, K2,
AC31, AE31, AG1, AG31,
AJ31, AK2, AK30, AL3, AL5,
AL7, AL21, AL23, AL25,
AL27
Supply voltage for LVCMOS core logic.
Supply voltage for normal high level at micromirror address
electrodes.
VCC
Power
Power
Analog
Analog
H18, H24, M6, M26, P6, P26,
T6, T26, V6, V26, Y6, Y26,
AD6, AD12, AD18, AD24
VCCI
Supply voltage for LVDS receivers.
A1, B12, B18, B24, B30, C7,
C13, C19, C25, D6, D12,
D18, D24, D30, E1, E7, E13,
E19, E25, F6, F12, F18, F24,
F30, G7, G13, G19, G25, K4,
K6, K26, K28, K30, M2, M30,
N5, N27, R5, T2, T30, U27,
V2, V30, W5, Y28, AB2, AB4,
AB6, AB26, AB28, AB30,
AC5, AD30, AE7, AE13,
VSS
Power
Analog
Device ground. Common return for all power.
AE19, AE25, AF6, AF12,
AF18, AF24, AF30, AG7,
AG13, AG19, AG25, AH6,
AH12, AH18, AH24, AH30,
AJ1, AJ7, AJ13, AJ19, AJ25,
AK6, AK12, AK18, AL29
(1) The following power supplies are required to operate the DMD: VCC, VCCI, VOFFSET, VBIAS, and VRESET. VSS must also be connected.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
(1)
See
.
MIN
MAX
UNIT
SUPPLY VOLTAGES
(2)
VCC
Supply voltage for LVCMOS core logic
–0.5
–0.5
4
4
V
V
(2)
VCCI
Supply voltage for LVDS receivers
Supply voltage for HVCMOS and micromirror
electrode
VOFFSET
–0.5
9
V
(2) (3)
(2)
VBIAS
Supply voltage for micromirror electrode
–0.5
–11
17
0.5
V
V
V
V
(2)
VRESET
Supply voltage for micromirror electrode
(4)
|VCC – VCCI
|VBIAS – VOFFSET
INPUT VOLTAGES
|
Supply voltage delta (absolute value)
0.3
(5)
|
Supply voltage delta (absolute value)
8.75
(2)
Input voltage for all other LVCMOS input pins
–0.5
–0.5
VCC + 0.3
VCCI + 0.3
700
V
V
(2) (6)
Input voltage for all other LVDS input pins
(7)
|VID
|
Input differential voltage (absolute value)
mV
mA
(7)
IID
Input differential current
7
CLOCKS
Clock frequency for LVDS interface, DCLK_A
Clock frequency for LVDS interface, DCLK_B
Clock frequency for LVDS interface, DCLK_C
Clock frequency for LVDS interface, DCLK_D
500
500
500
500
ƒclock
MHz
ENVIRONMENTAL
(8)
Array temperature: Operational
20
–40
20
30
90
30
90
TARRAY
ºC
ºC
(8)
Array temperature: Non–operational
Window temperature: Operational
TWINDOW
Window temperature: Non–operational
–40
Absolute temperature delta between the window test
points and the ceramic test point TP1(9)
|TDELTA
|
10
95
ºC
%
RH
Relative humidity, operating and non–operating
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure above Recommended Operating Conditions for extended periods may affect device reliability.
(2) All voltages are referenced to common ground VSS. Supply voltages VCC, VCCI, VOFFSET, VBIAS, and VRESET are all required for proper
DMD operation. VSS must also be connected.
(3) VOFFSET supply transients must fall within specified voltages.
(4) To prevent excess current, the supply voltage delta |VCCI – VCC| must be less than specified limit.
(5) To prevent excess current, the supply voltage delta |VBIAS – VOFFSET| must be less than specified limit. Refer to Power Supply
Requirements for additional information.
(6) This maximum LVDS input voltage rating applies when each input of a differential pair is at the same voltage potential.
(7) LVDS differential inputs must not exceed the specified limit or damage may result to the internal termination resistors.
(8) The highest temperature of the active array as calculated by the Micromirror Array Temperature Calculation using ceramic test point 1
(TP1) in Figure 15.
(9) Temperature delta is the highest difference between the ceramic test point TP1 and window test points TP2 and TP3 in Figure 15.
6.2 Storage Conditions
Applicable for the DMD as a component or non-operating in a system.
MIN
MAX
80
UNIT
°C
TDMD
RH
DMD storage temperature
–40
Relative humidity, (non-condensing)
95
%
10
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
6.3 ESD Ratings
VALUE
UNIT
(1)
V(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins
±2000
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.4 Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted)(1)
MIN
NOM
MAX
UNIT
(2)
SUPPLY VOLTAGES
VCC
Supply voltage for LVCMOS core logic
3.3
3.3
3.45
3.45
8.5
3.6
3.6
V
V
V
V
V
V
V
VCCI
Supply voltage for LVDS receivers
(3)
VOFFSET
VBIAS
VRESET
Supply voltage for HVCMOS and micromirror electrodes
8.25
15.5
–9.5
8.75
16.5
–10.5
0.3
16
Supply voltage for micromirror electrodes
–10
(4)
|VCCI–VCC
|
Supply voltage delta (absolute value)
(5)
|VBIAS–VOFFSET
|
Supply voltage delta (absolute value)
8.75
LVCMOS PINS
VIH
(6)
High level Input voltage
1.7
2.5
VCC + 0.3
V
V
(6)
VIL
Low level Input voltage
–0.3
0.7
–20
15
IOH
High level output current at VOH = 2.4 V
Low level output current at VOL = 0.4 V
mA
mA
ns
IOL
(7)
TPWRDNZ
SCP INTERFACE
ƒclock
PWRDNZ pulse width
10
(8)
SCP clock frequency
500
800
700
kHz
ns
(9)
tSCP_SKEW
tSCP_DELAY
tSCP_BYTE_INTERVAL
tSCP_NEG_ENZ
tSCP_PW_ENZ
tSCP_OUT_EN
ƒclock
Time between valid SCPDI and rising edge of SCPCLK
Time between valid SCPDO and rising edge of SCPCLK
Time between consecutive bytes
–800
(9)
ns
1
30
1
µs
Time between falling edge of SCPENZ and the first rising edge of SCPCLK
SCPENZ inactive pulse width (high level)
ns
µs
Time required for SCP output buffer to recover after SCPENZ (from tri-state)
1.5
ns
(10)
SCP circuit clock oscillator frequency
9.6
11.1
MHz
(1) The functional performance of the device specified in this data sheet is achieved when operating the device within the limits defined by
this table. No level of performance is implied when operating the device above or below these limits.
(2) Supply voltages VCC, VCCI, VOFFSET, VBIAS, and VRESET are all required for proper DMD operation. VSS must also be connected. All
voltages are referenced to common ground VSS
.
(3) VOFFSET supply transients must fall within specified max voltages.
(4) To prevent excess current, the supply voltage delta |VCCI – VCC| must be less than the specified limit.
(5) To prevent excess current, the supply voltage delta |VBIAS – VOFFSET| must be less than the specified limit. Refer to Power Supply
Requirements for additional information.
(6) Tester conditions for VIH and VIL:
Frequency = 60 MHz. Maximum rise time = 2.5 ns at (20% to 80%)
Frequency = 60 MHz. Maximum fall time = 2.5 ns at (80% to 20%)
(7) PWRDNZ input pin resets the SCP and disables the LVDS receivers. PWRDNZ input pin overrides SCPENZ input pin and tri-states the
SCPDO output pin.
(8) The SCP clock is a gated clock. Duty cycle shall be 50% ± 10%. SCP parameter is related to the frequency of DCLK.
(9) Refer to Figure 1.
(10) SCP internal oscillator is specified to operate all SCP registers. For all SCP operations, DCLK is required.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
Recommended Operating Conditions (continued)
Over operating free-air temperature range (unless otherwise noted)(1)
MIN
NOM
MAX
UNIT
LVDS INTERFACE
(11)
ƒclock
|VID
Clock frequency DCLK
400
100
400 or 480
400
480
600
MHz
mV
mV
mV
ns
(12)
|
Input differential voltage (absolute value)
(12)
VCM
Common mode
1200
(12)
VLVDS
tLVDS_RSTZ
ZIN
LVDS voltage
0
2000
10
Time required for LVDS receivers to recover from PWRDNZ
Internal differential termination resistance
95
90
105
110
Ω
ZLINE
Line differential impedance (PWB/trace)
100
Ω
ENVIRONMENTAL(13)
Total combined <353 nm(15)
10
2.5
5.8
2.5
5.8
5
mW/cm2
W/cm2
W
Max per single wavelength(16)
355 nm to 365 nm
W/cm2
W
Total Combined
355 nm to 365 nm
W/cm2
W
Max per single wavelength(16)
365 nm to 400 nm
11.6
10
W/cm2
W
Total Combined
365 nm to 400 nm
Illumination power density and illumination
ILLPD and ILLTP
total power on the array(14)
23.3
15
W/cm2
W
Max per single wavelength(16)
400 nm to 420 nm
34.8
15
W/cm2
W
Total Combined
400 nm to 420 nm
34.8
15
W/cm2
W
Total Combined
355 nm to 420 nm
34.8
Thermally
Limited
Total Combined >420 nm(17)
W/cm2
(19)
TARRAY
Array temperature(18)
20
20
30
30
°C
°C
TWINDOW
Window temperature measured at test points TP2 and TP3
Absolute temperature delta between the window test points (TP2, TP3) and the
ceramic test point TP1.(20)
|TDELTA
|
10
95
°C
RH
Relative Humidity (non-condensing)
Operating Landed Duty Cycle(21)
%
%
50
(11) The DLP9000XUV DMD, coupled with the DLPC910, is designed for operation at 2 specific DCLK frequencies only: 400 MHz or 480
MHz, but not random values in between.
(12) Refer to Figure 2, Figure 3, and Figure 4.
(13) Optimal, long-term performance and optical efficiency of the digital micromirror device (DMD) can be affected by various application
parameters, including illumination spectrum, illumination power density, micromirror landed duty-cycle, ambient temperature (storage
and operating), DMD temperature, ambient humidity (storage and operating), and power on or off duty cycle. TI recommends that
application-specific effects be considered as early as possible in the design cycle.
(14) This is the illumination power density and illumination total power input to the DMD micromirror array and does not include illumination
overfill of the DMD device outside the active array.
(15) Any 355 nm or higher illumination source must use a cutoff filter to be at or below this power level by 353 nm. Illumination power from
355 nm down to 353 nm is expected to be diminishing such that the maximum power limit at 353 nm can be achieved.
(16) Integrated power in any single 3 nm band.
(17) Limited by the resulting micromirror array temperature. Refer to TARRAY, |TDELTA|, and Micromirror Array Temperature Calculation for
information related to verifying the DMD temperature meets its requirements.
(18) The array temperature cannot be measured directly and must be computed analytically from the temperature measured at test point 1
(TP1) shown in Figure 15 and the package thermal resistance in Thermal Information using Micromirror Array Temperature Calculation.
(19) Simultaneous exposure of the DMD to the maximum Recommended Operating Conditions for temperature and UV illumination will
reduce device lifetime.
(20) Temperature delta is the highest difference between the ceramic test point (TP1) and window test points (TP2) and (TP3) in Figure 15.
(21) Landed duty cycle refers to the percentage of time an individual micromirror spends landed in one state (12° or –12°) versus the
opposite state (–12° or 12°). 50% equates to a 50/50 duty cycle where the mirror has been landed 50% in the On-state and 50% in the
Off-state. See Micromirror Landed-On/Landed-Off Duty Cycle for more information on Landed Duty Cycle.
12
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
6.5 Thermal Information
DLP9000XUV
(1)
THERMAL METRIC
FLS (CLGA)
355 PINS
0.5
UNIT
Thermal resistance, active area to test point 1 (TP1)
°C/W
(1) The DMD is designed to conduct absorbed and dissipated heat to the back of the package where it can be removed by an appropriate
heat sink. The heat sink and cooling system must be capable of maintaining the package within the temperature range specified in the
Recommended Operating Conditions. The total heat load on the DMD is largely driven by the incident light absorbed by the active area,
although other contributions include light energy absorbed by the window aperture and electrical power dissipation of the array. Optical
systems should be designed to minimize the light energy falling outside the window clear aperture since any additional thermal load in
this area can significantly degrade the reliability of the device.
6.6 Electrical Characteristics
Over operating free-air temperature range (unless otherwise noted)
(1)
PARAMETER
TEST CONDITIONS
VCC = 3.0 V, IOH = –20 mA
MIN TYP
MAX UNIT
VOH
High-level output voltage
Low level output voltage
2.4
V
VOL
VCC = 3.6 V, IOL = 15 mA
VCC = 3.6 V, VI = VCC
VCC = 3.6 V, VI = 0
VCC = 3.6 V
0.4
V
(2) (3)
IIH
High–level input current
Low level input current
250
µA
µA
µA
IlL
–250
IOZ
High–impedance output current
10
CURRENT
ICC
VCC = 3.6 V, DCLK = 480 MHz
VCCI = 3.6 V, DCLK = 480 MHz
VOFFSET = 8.75 V
1850
1100
25
(4)
Supply current
mA
mA
mA
ICCI
IOFFSET
IBIAS
(5)
Supply current
VBIAS = 16.5 V
14
IRESET
ITOTAL
POWER
PCC
VRESET = –10.5 V
11
Supply current
DLP9000XUV Total Sum
3000
VCC = 3.6 V
6660
3960
219
mW
mW
mW
mW
mW
mW
PCCI
VCCI = 3.6 V
POFFSET
PBIAS
PRESET
PTOTAL
CAPACITANCE
CI
Supply power dissipation
Supply power dissipation
VOFFSET = 8.75 V
VBIAS = 16.5 V
231
VRESET = –10.5 V
Total sum, DCLK = 480 MHz
115
11185
Input capacitance
Output capacitance
ƒ = 1 MHz
ƒ = 1 MHz
10
10
pF
pF
CO
Reset group capacitance
MBRST(31:0)
ƒ = 1 MHz; 2560 × 50 micromirrors
230
290
pF
(1) All voltages are referenced to common ground VSS. Supply voltages VCC, VCCI, VOFFSET, VBIAS, and VRESET are all required for proper
DMD operation. VSS must also be connected.
(2) Applies to LVCMOS input pins only. Does not apply to LVDS pins and MBRST pins.
(3) LVCMOS input pins utilize an internal 18000 Ω passive resistor for pull-up and pull-down configurations. Refer to Pin Configuration and
Functions to determine pull-up or pull-down configuration used.
(4) To prevent excess current, the supply voltage delta |VCCI – VCC| must be less than the specified limit.
(5) To prevent excess current, the supply voltage delta |VBIAS – VOFFSET| must be less than the specified limit.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
6.7 Timing Requirements
Over Recommended Operating Conditions (unless otherwise noted)
(1)
MIN
NOM
MAX
UNIT
(2)
SCP INTERFACE
tr
Rise time
20% to 80%
80% to 20%
200
200
ns
ns
tƒ
Fall time
(2)
LVDS INTERFACE
tr
Rise time
20% to 80%
80% to 20%
100
100
400
400
ps
ps
tƒ
Fall time
(3)
LVDS CLOCKS
DCLK_A, 50% to 50%
DCLK_B, 50% to 50%
DCLK_C, 50% to 50%
DCLK_D, 50% to 50%
DCLK_A, 50% to 50%
DCLK_B, 50% to 50%
DCLK_C, 50% to 50%
DCLK_D, 50% to 50%
2.083
2.083
2.083
2.083
1.031
1.031
1.031
1.031
tc
Cycle time
ns
ns
1.042
1.042
1.042
1.042
tw
Pulse duration
(3)
LVDS INTERFACE
D_A(15:0) before rising or falling edge of DCLK_A
D_B(15:0) before rising or falling edge of DCLK_B
D_C(15:0) before rising or falling edge of DCLK_C
D_D(15:0) before rising or falling edge of DCLK_D
D_A(15:0) after rising or falling edge of DCLK_A
D_B(15:0) after rising or falling edge of DCLK_B
D_C(15:0) after rising or falling edge of DCLK_C
D_D(15:0) after rising or falling edge of DCLK_D
0.2
0.2
0.2
0.2
0.4
0.4
0.4
0.4
tsu
Setup time
ns
ns
th
Hold time
(3)
LVDS INTERFACE
Channel A includes the following LVDS pairs:
DCLK_AP and DCLK_AN
SCTRL_AP and SCTRL_AN
D_AP(15:0) and D_AN(15:0)
–1.04
1.04
ns
Channel B includes the following LVDS pairs:
DCLK_BP and DCLK_BN
SCTRL_BP and SCTRL_BN
D_BP(15:0) and D_BN(15:0)
tskew
Skew time
Channel C includes the following LVDS pairs:
DCLK_CP and DCLK_CN
SCTRL_CP and SCTRL_CN
D_CP(15:0) and D_CN(15:0)
–1.04
1.04
ns
Channel D includes the following LVDS pairs:
DCLK_DP and DCLK_DN
SCTRL_DP and SCTRL_DN
D_DP(15:0) and D_DN(15:0)
(1) Refer to Pin Configuration and Functions for pin details.
(2) Refer to Figure 5.
(3) Refer to Figure 6.
14
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
t
c
f = 1 / t
clock c
SCPCLK
50%
50%
tSCP_SKEW
SCPDI
50%
tSCP_DELAY
SCPD0
50%
Not to scale.
Refer to SCP Interface section of the Recommended Operating Conditions.
Figure 1. SCP Timing Parameters
(VIP + VIN) / 2
DCLK_P , SCTRL_P , D_P(15:0)
LVDS
Receiver
VID
VIP
DCLK_N , SCTRL_N , D_N(15:0)
VCM
VIN
Refer to LVDS Interface section of the Recommended Operating Conditions table.
Refer to Pin Configuration and Functions for a list of LVDS pins.
Figure 2. LVDS Voltage Definitions (References)
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
VLVDS max = VCM max + | 1/2 * VID max
|
VCM
VID
VLVDS min = VCM min œ | 1/2 * VID max
|
Not to scale.
Refer to LVDS Interface section of the Recommended Operating Conditions table.
Figure 3. LVDS Voltage Parameters
DCLK_P , SCTRL_P , D_P(15:0)
ESD
Internal
Termination
LVDS
Receiver
DCLK_N , SCTRL_N , D_N(15:0)
ESD
Refer to LVDS Interface section of the Recommended Operating Conditions table.
Refer to Pin Configuration and Functions for list of LVDS pins.
Figure 4. LVDS Equivalent Input Circuit
LVDS Interface
SCP Interface
1.0 * VCC
1.0 * V
ID
V
CM
0.0 * VCC
0.0 * V
ID
tr
tf
tr
tf
Not to scale.
Refer to the Timing Requirements in Timing Requirements.
Refer to Pin Configuration and Functions for a list of LVDS pins and SCP pins.
Figure 5. Rise Time and Fall Time
16
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Not to scale.
Refer to LVDS INTERFACE section in the Timing Requirements table.
Figure 6. Timing Requirement Parameter Definitions
Not to scale.
Refer to LVDS INTERFACE section in the Timing Requirements table.
Figure 7. LVDS Interface Channel Skew Definition
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
6.8 Capacitance at Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
PARAMETER
Input capacitance
TEST CONDITIONS
ƒ = 1 MHz
MIN
MAX
10
UNIT
pF
CI
CO
CIM
Output capacitance
ƒ = 1 MHz
10
pF
MBRST(31:0) input capacitance
ƒ = 1 MHz. All inputs interconnected.
230
290
pF
6.9 Typical Characteristics
When the DLP9000XUV DMD is controlled by the DLPC910 controller, the digital controller offers streaming 1-bit
binary patterns to the DMD at speeds greater than 61 Gigabits per second (Gbps). The patterns are streamed
from a customer designed applications processor into the DLPC910 input LVDS data interface. Table 1 shows
the pattern rates for the different DMD reset modes.
Table 1. DLPC910 with DLP9000XUV DMD Pattern Rates versus Reset Mode
(3)
RESET MODE(1)
Global
MAX PIXEL DATA RATE (Gbps)(2)
MAX PATTERN RATE (Hz)
53.42
56.46
59.89
61.39
13043
Single
13783(4)
14624(4)
14989(4)
Dual
Quad
(1) Refer to the DLPC910 data sheet in Related Documentation for a description of the reset modes.
(2) Pixel data rates are based on continuous streaming.
(3) Increasing exposure periods may be necessary for a desired application but may decrease pattern rate.
(4) This reset mode typically requires pulsed illumination such as a laser or LED.
18
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
6.10 System Mounting Interface Loads
PARAMETER
MIN
NOM
MAX UNIT
Thermal interface area (See Figure 8)(1)(2)
156
1334
712
N
N
N
Maximum system mounting interface
load to be applied to the:
(1)(2)
Electrical interface area
(1)(2)
Datum A interface area
(1) Refer to the DMD Mounting Concepts guide in Related Documentation for more DMD mounting information.
(2) Combined loads of the thermal and electrical interface areas in excess of Datum “A” load shall be evenly distributed outside the Datum
A area (1334 + 156 – Datum A).
Thermal
Interface Area
Electrical
Interface Area
Other Area
Datum ‘A’ Area
Figure 8. System Mounting Interface Loads
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
6.11 Micromirror Array Physical Characteristics
VALUE
2560
UNIT
M
N
P
Number of active columns
Number of active rows
micromirrors
1600
micromirrors
Micromirror (pixel) pitch
Micromirror active array width
Micromirror active array height
Micromirror active border
Micromirror total area
See Figure 9
7.56
µm
M × P
19.3536
12.096
14
mm
mm
N × P
(1)
Pond of micromirror (POM)
P2 × M × N (converted to cm)
micromirrors/side
cm2
2.341
(1) The structure and qualities of the border around the active array includes a band of partially functional micromirrors called the POM.
These micromirrors are structurally and/or electrically prevented from tilting toward the bright or ON state, but still require an electrical
bias to tilt toward OFF.
0
1
2
3
DMD Active Array
N x P
M x N Micromirrors
N œ 4
N œ 3
N œ 2
N œ 1
M x P
P
Border micromirrors omitted for clarity.
Details omitted for clarity.
P
Not to scale.
P
P
Refer to section Micromirror Array Physical Characteristics table for M, N, and P specifications.
Figure 9. Micromirror Array Physical Characteristics
20
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
6.12 Micromirror Array Optical Characteristics
Refer to Optical Interface and System Image Quality for important information.
PARAMETER
TEST CONDITIONS
MIN
NOM
MAX
UNIT
Micromirror Landed
(1)
α
β
Micromirror tilt angle
12
degree
(2)
State
(1)(2) (3) (4) (5) (6)
Micromirror tilt angle range tolerance
-1
1
46
0
degree
degree
(7)
Micromirror Hinge Axis Orientation
See Figure 10 and
Figure 13
44
45
Adjacent micromirrors
(8)
Number of out-of-specification micromirrors
micromirrors
Non-adjacent
micromirrors
10
(9) (10)
Micromirror crossover time
Typical performance
2.5
μs
DMD efficiency within the wavelength range 355 nm to 420 nm
68%
(11)
(1) α and β are an average of 5 measured locations on the DMD.
(2) Measured relative to the plane formed by the overall micromirror array.
(3) Additional variation exists between the micromirror array and the package datums.
(4) Represents the landed tilt angle variation relative to the nominal landed tilt angle.
(5) Represents the positive tilt angle variation that can occur between any two individual micromirrors, located on the same device.
(6) For some applications, it is critical to account for the micromirror tilt angle variation in the overall system optical design. With some
system optical designs, the micromirror tilt angle variation within a device may result in perceivable non-uniformities in the light field
reflected from the micromirror array. With some system optical designs, the micromirror tilt angle variation between devices may result in
colorimetry variations, system efficiency variations, or system contrast variations.
(7) When the micromirror array is landed (not parked), the tilt direction of each individual micromirror is dictated by the binary contents of
the CMOS memory cell associated with each individual micromirror. A binary value of 1 results in a micromirror landing in the ON State
direction. A binary value of 0 results in a micromirror landing in the OFF State direction.
(8) An out-of-specification micromirror is defined as a micromirror that is unable to transition between the two landed states within the
specified micromirror switching time.
(9) Micromirror crossover time is primarily a function of the natural response time of the micromirrors.
(10) Performance as measured at the start of life.
(11) Efficiency numbers assume 24-degree illumination angle, F/2.4 illumination and collection cones, uniform source spectrum, and uniform
pupil illumination. Efficiency numbers assume 100% electronic mirror duty cycle and do not include optical overfill loss. Note that this
number is specified under conditions described above and deviations from the specified conditions could result in decreased efficiency.
illumination
Not To Scale
0
1
2
3
On-State
Tilt Direction
Off-State
45°
Tilt Direction
N œ 4
N œ 3
N œ 2
N œ 1
Refer to section Micromirror Array Physical Characteristics table for M, N, and P specifications.
Figure 10. Micromirror Landed Orientation and Tilt
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
6.13 Optical and System Image Quality
Optimizing system optical performance and image quality strongly relate to optical system design parameter
trades. Although it is not possible to anticipate every conceivable application, optical performance is contingent
on compliance to the optical system operating conditions described in a) through c) below:
a. Numerical Aperture and Stray Light Control: The angle defined by the numerical aperture of the
illumination and projection optics at the DMD optical area should be the same. This angle should not exceed
the nominal device mirror tilt angle unless appropriate apertures are added in the illumination and/or
projection pupils to block out flat-state and stray light from the projection lens. The mirror tilt angle defines
DMD capability to separate the "ON" optical path from any other light path, including undesirable flat-state
specular reflections from the DMD window, DMD border structures, or other system surfaces near the DMD
such as prism or lens surfaces. If the numerical aperture exceeds the mirror tilt angle, or if the projection
numerical aperture angle is more than two degrees larger than the illumination numerical aperture angle,
artifacts could occur in the projected image of the DMD border region and/or active area.
b. Pupil Match: TI’s optical and image quality specifications assume that the exit pupil of the illumination optics
is nominally centered within two degrees of the entrance pupil of the projection optics. Misalignment of pupils
can create artifacts in the projection of the DMD border region and/or active area which may require
additional system apertures to control, especially if the numerical aperture of the system exceeds the pixel tilt
angle.
c. Illumination Overfill: Overfill light illuminating the DMD area far enough outside the active array may strike
mechanical features that surround the active array or other surface anomalies resulting in scattered or
reflected light which may impact the projected image performance in certain customer applications. The
illumination optical system should be designed to limit these artifacts by minimizing the amount of light
incident outside the active array to the point where the image performance is in line with the expected
application image performance. The design also needs to take into account the particular system’s optical
architecture and light engine assembly tolerances.
NOTE
TI ASSUMES NO RESPONSIBILITY FOR IMAGE QUALITY ARTIFACTS OR DMD
FAILURES CAUSED BY OPTICAL SYSTEM OPERATING CONDITIONS EXCEEDING
LIMITS DESCRIBED ABOVE.
6.14 Window Characteristics
(1)
PARAMETER
Window material designation
Window refractive index
Window aperture
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Corning 7056
1.487
At wavelength 589 nm
(2)
See
Illumination overfill
Refer to Illumination Overfill
Window Artifact Size
Area within the window aperture only.
400
μm
Window transmittance, single–pass
through both surfaces and glass
Minimum within the wavelength range 355 nm to 420 nm.
Applies to all angles 0° to 30° AOI.
97%
(3)
(1) Refer to Window Characteristics and Optics for more information.
(2) For details regarding the size and location of the window aperture, refer to the package mechanical characteristics listed in the
Mechanical ICD in the Mechanical, Packaging, and Orderable Information section.
(3) Refer to the TI application report DLPA031, Wavelength Transmittance Considerations for DLP DMD Window.
6.15 Chipset Component Usage Specification
The DMD is a component of one or more DLP® chipsets. Reliable function and operation of the DMD requires
that it be used in conjunction with the other components of the applicable DLP chipset, including those
components that contain or implement TI DMD control technology. TI DMD control technology consists of the TI
technology and devices for operating or controlling a DMD.
22
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
7 Parameter Measurement Information
The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its
transmission line effects must be taken into account. Figure 11 shows an equivalent test load circuit for the
output under test. The load capacitance value stated is only for characterization and measurement of AC timing
signals. This load capacitance value does not indicate the maximum load the device is capable of driving.
Timing reference loads are not intended as a precise representation of any particular system environment or
depiction of the actual load presented by a production test. System designers should use IBIS or other simulation
tools to correlate the timing reference load to a system environment. Refer to the Application and Implementation
section.
Device Pin
Tester Channel
Output Under Test
CLOAD
Figure 11. Test Load Circuit
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
8 Detailed Description
8.1 Overview
The DMD is a 0.9 inch diagonal spatial light modulator which consists of an array of highly reflective aluminum
micromirrors. Pixel array size and square grid pixel arrangement are shown in Figure 9.
The DMD is an electrical input, optical output micro-electrical-mechanical system (MEMS). The electrical
interface is Low Voltage Differential Signaling (LVDS), Double Data Rate (DDR).
The DMD consists of a two-dimensional array of 1-bit CMOS memory cells. The array is organized in a grid of M
memory cell columns by N memory cell rows. Refer to the Functional Block Diagram.
The positive or negative deflection angle of the micromirrors can be individually controlled by changing the
address voltage of underlying CMOS addressing circuitry and micromirror reset signals (MBRST).
Each cell of the M × N memory array drives its true and complement (‘Q’ and ‘QB’) data to two electrodes
underlying one micromirror, one electrode on each side of the diagonal axis of rotation. Refer to Micromirror
Array Optical Characteristics. The micromirrors are electrically tied to the micromirror reset signals (MBRST) and
the micromirror array is divided into reset groups.
Electrostatic potentials between a micromirror and its memory data electrodes cause the micromirror to tilt
toward the illumination source in a DLP projection system or away from it, thus reflecting its incident light into or
out of an optical collection aperture. The positive (+) tilt angle state corresponds to an 'on' pixel, and the negative
(–) tilt angle state corresponds to an 'off' pixel.
Refer to Micromirror Array Optical Characteristics for the ± tilt angle specifications. Refer to Pin Configuration
and Functions for more information on micromirror reset control.
24
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
8.2 Functional Block Diagram
Not to Scale. Details Omitted for Clarity. See Accompanying Notes in this Section.
Channel A
Interface
Channel C
Interface
Control
Column Read & Write
Control
(0,0)
Word Lines
Word Lines
Voltages
Row
Row
Micromirror Array
Voltage
Generators
Voltage
Generators
Voltages
(M-1, N-1)
Control
Column Read & Write
Control
Channel B
Interface
Channel D
Interface
For pin details on Channels A, B, C, and D, refer to Pin Configuration and Functions and LVDS Interface section of
Timing Requirements.
Figure 12. Functional Block Diagram
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
8.3 Feature Description
The DMD consists of 4096000 highly reflective, digitally switchable, micrometer-sized mirrors (micromirrors)
organized in a two-dimensional orthogonal pixel array. Refer to Figure 9 and Figure 13.
Each aluminum micromirror is switchable between two discrete angular positions, –α and +α. The angular
positions are measured relative to the micromirror array plane, which is parallel to the silicon substrate. Refer to
Micromirror Array Optical Characteristics and Figure 14.
The parked position of the DMD micromirrors is not an operational mode which is electrostatically driven.
Therefore, the DMD micromirrors are not driven to a known landed position and the individual micromirror flat-
state angular positions may vary from the DMD array plane. Tilt direction of the micromirror is perpendicular to
the hinge-axis. The on-state landed position is directed toward the left-top edge of the package, as shown in
Figure 13.
Each individual micromirror is positioned over a corresponding CMOS memory cell. The angular position of a
specific micromirror is determined by the binary state (logic 0 or 1) of the corresponding CMOS memory cell
contents, after the mirror clocking pulse is applied. The angular position (–α and +α) of the individual micromirrors
changes synchronously with a micromirror clocking pulse, rather than being coincident with the CMOS memory
cell data update.
Writing logic 1 into a memory cell followed by a mirror clocking pulse results in the corresponding micromirror
switching to a +α position. Writing logic 0 into a memory cell followed by a mirror clocking pulse results in the
corresponding micromirror switching to a – α position.
Updating the angular position of the micromirror array consists of two steps. First, update the contents of the
CMOS memory. Second, apply a micromirror reset (also referred as Mirror Clocking Pulse) to all or a portion of
the micromirror array (depending upon the configuration of the system). Micromirror reset pulses are generated
internally by the DMD, with application of the pulses being coordinated by the DLPC910 digital controller.
For more information, refer to the TI application report DLPA008, DMD101: Introduction to Digital Micromirror
Device (DMD) Technology.
26
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Feature Description (continued)
Incident
Illumination
Package Pin
A1 Corner
Details Omitted For Clarity.
Not To Scale.
DMD
Micromirror
Array
Active Micromirror Array
(Border micromirrors eliminated for clarity)
0
Nœ1
Micromirror Pitch
Micromirror Hinge-Axis Orientation
P (um)
—On-State“
Tilt Direction
45°
—Off-State“
Tilt Direction
P (um)
Refer to Micromirror Array Physical Characteristics, Figure 9, and Figure 10.
Figure 13. Micromirror Array, Pitch, Hinge Axis Orientation
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
Feature Description (continued)
Details Omitted For Clarity.
Not To Scale.
Package Pin
A1 Corner
DMD
Incident
Illumination
Two
Two
—On-State“ —Off-State“
Micromirrors Micromirrors
For Reference
Flat-State
( —parked“ )
Micromirror Position
a
b
-a
b
Silicon Substrate
Silicon Substrate
—On-State“
Micromirror
—Off-State“
Micromirror
Micromirror States: On, Off, Flat
Figure 14. Micromirror States: On, Off, Flat
28
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
8.4 Device Functional Modes
The DLP9000XUV DMD is controlled by one DLPC910 digital controller. The digital controller offers high speed
streaming mode where 1-bit binary patterns are accepted at the LVDS interface input, and then streamed to the
DMD. To ensure reliable operation, the DLP9000XUV DMD must always be used with the DLPC910 controller.
For more information, refer to the DLPC910 data sheet listed under Related Documentation.
8.5 Window Characteristics and Optics
NOTE
TI assumes no responsibility for image quality artifacts or DMD failures caused by optical
system operating conditions exceeding limits described previously.
8.5.1 Optical Interface and System Image Quality
TI assumes no responsibility for end-equipment optical performance. Achieving the desired end-equipment
optical performance involves making trade-offs between numerous component and system design parameters.
Optimizing system optical performance and image quality strongly relate to optical system design parameter
trades. Although it is not possible to anticipate every conceivable application, projector image quality and optical
performance is contingent on compliance to the optical system operating conditions described in the following
sections.
8.5.2 Numerical Aperture and Stray Light Control
The angle defined by the numerical aperture of the illumination and projection optics at the DMD optical area
should be the same. This angle should not exceed the nominal device mirror tilt angle unless appropriate
apertures are added in the illumination and/or projection pupils to block out flat-state and stray light from the
projection lens. The mirror tilt angle defines DMD capability to separate the "ON" optical path from any other light
path, including undesirable flat-state specular reflections from the DMD window, DMD border structures, or other
system surfaces near the DMD such as prism or lens surfaces. If the numerical aperture exceeds the mirror tilt
angle, or if the projection numerical aperture angle is more than two degrees larger than the illumination
numerical aperture angle, objectionable artifacts in the display’s border and/or active area could occur.
8.5.3 Pupil Match
TI’s optical specifications assume that the exit pupil of the illumination optics is nominally centered within 2° (two
degrees) of the entrance pupil of the projection optics. Misalignment of pupils can create objectionable artifacts in
the display’s border and/or active area, which may require additional system apertures to control, especially if the
numerical aperture of the system exceeds the pixel tilt angle.
8.5.4 Illumination Overfill
The active area of the device is surrounded by an aperture on the inside DMD window surface that masks
structures of the DMD device assembly from normal view. The aperture is sized to anticipate several optical
operating conditions. Overfill light illuminating the window aperture can create artifacts from the edge of the
window aperture opening and other surface anomalies that may be visible on the screen. The illumination optical
system should be designed to limit light flux incident anywhere on the window aperture from exceeding
approximately 10% of the average flux level in the active area. Depending on the particular system’s optical
architecture, overfill light may have to be further reduced below the suggested 10% level in order to be
acceptable.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
8.6 Micromirror Array Temperature Calculation
Figure 15. DMD Thermal Test Points
Micromirror array temperature can be computed analytically from measurement points on the outside of the
package, the package thermal resistance, the electrical power, and the illumination heat load. The relationship
between micromirror array temperature and the reference ceramic temperature is provided by the following
equations:
TARRAY = T CERAMIC + (QARRAY × RARRAY-TO-CERAMIC
QARRAY = QELECTRICAL + QILLUMINATION
)
)
where:
•
•
•
•
•
•
•
•
TARRAY = Computed array temperature (°C)
TCERAMIC = Measured ceramic temperature (°C) (TP1 location)
RARRAY-TO-CERAMIC = Thermal resistance of DMD package from array to ceramic TP1 (°C/W)
QARRAY = Total DMD power (electrical and absorbed) on the array (Watts)
QELECTRICAL = Nominal electrical power (Watts)
QINCIDENT = Incident Illumination optical power (W)
QILLUMINATION = (DMD average thermal absorptivity x QINCIDENT) (W)
DMD average thermal absorptivity = 0.39
The electrical power dissipation of the DMD is variable and depends on the voltages, data rates, and pattern
rates of the DMD within the intended application. For the example array temperature calculation shown below,
the maximum value of 11.2 W is used for the electrical power dissipation. Since the electrical power dissipation
of the DMD is application dependent, customers will want to test and use their own application dependent power
values in their array temperature calculation. The absorbed power from the illumination source is variable and
depends on the operating state of the micromirrors and the intensity of the light source. The equations shown
above are valid for each DMD chip in a system. The absorption factor of 0.39 assumes the array is fully
illuminated with an illumination distribution of 90% on the active array and 10% overfill on the array border. It is
strongly recommended to minimize illumination overfill as much as possible which will, in turn, maximize the
active array illumination, increase overall system efficiency, and reduce DMD thermal heating.
The following is a sample Calculation for each DMD in a system with a measured illumination power density:
•
•
•
•
•
TCeramic = 15°C (measured)
ILLDENSITY = 15 Watts per cm2 (optical power on DMD per unit area) (measured)
Overfill = 10% (optical design)
QELECTRICAL = 11.2 Watts
RARRAY-TO-CERAMIC = 0.5 °C/W
30
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Micromirror Array Temperature Calculation (continued)
•
•
•
•
•
Area of array = ( 1.9354 cm x 1.2096 cm ) = 2.34 cm2
ILLAREA = 2.34 cm2 / (90%) = 2.6 cm2
QINCIDENT =15 W/cm2 x 2.6 cm2 = 39.0 W
QARRAY = 11.2 W + (0.39 x 39.0 W) = 26.4 W
TARRAY =15°C + (26.4 W x 0.5 °C) = 28.2 °C
8.7 Micromirror Landed-On/Landed-Off Duty Cycle
8.7.1 Definition of Micromirror Landed-On/Landed-Off Duty Cycle
The micromirror landed-on/landed-off duty cycle (landed duty cycle) denotes the amount of time (as a
percentage) that an individual micromirror is landed in the On–state versus the amount of time the same
micromirror is landed in the Off–state.
As an example, a landed duty cycle of 100/0 indicates that the referenced pixel is in the On-state 100% of the
time (and in the Off-state 0% of the time); whereas 0/100 would indicate that the pixel is in the Off-state 100% of
the time. Likewise, 50/50 indicates that the pixel is On 50% of the time and Off 50% of the time.
Note that when assessing landed duty cycle, the time spent switching from one state (ON or OFF) to the other
state (OFF or ON) is considered negligible and is thus ignored.
Since a micromirror can only be landed in one state or the other (On or Off), the two numbers (percentages)
always add to 100.
8.7.2 Landed Duty Cycle and Useful Life of the DMD
Knowing the long-term average landed duty cycle (of the end product or application) is important because
subjecting all (or a portion) of the DMD’s micromirror array (also called the active array) to an asymmetric landed
duty cycle for a prolonged period of time can reduce the DMD’s usable life.
Note that it is the symmetry/asymmetry of the landed duty cycle that is of relevance. The symmetry of the landed
duty cycle is determined by how close the two numbers (percentages) are to being equal. For example, a landed
duty cycle of 50/50 is perfectly symmetrical whereas a landed duty cycle of 100/0 or 0/100 is perfectly
asymmetrical.
Individual DMD mirror duty cycles vary by application as well as the mirror location on the DMD within any
specific application. DMD mirror useful life are maximized when every individual mirror within a DMD approaches
50/50 (or 1/1) duty cycle. For the DLPC910 and DLP9000XUV chipset, it is recommended the controlling
applications processor provide a 50/50 pattern sequence to the DLPC910 for display on the DLP9000XUV DMD
as often as possible. The pattern provides a 50/50 duty cycle across the entire DMD mirror array, where the
mirrors are continuously flipped between the on and off states.
8.7.3 Landed Duty Cycle and Operational DMD Temperature
Operational DMD Temperature and Landed Duty Cycle interact to affect the DMD’s usable life.
8.7.4 Estimating the Long-Term Average Landed Duty Cycle of a Product or Application
During a given period of time, the Landed Duty Cycle of a given pixel follows from the image content being
displayed by that pixel.
For example, in the simplest case, when displaying pure-white on a given pixel for a given time period, that pixel
will experience a 100/0 Landed Duty Cycle during that time period. Likewise, when displaying pure-black, the
pixel will experience a 0/100 Landed Duty Cycle.
Between the two extremes (ignoring for the moment color and any image processing that may be applied to an
incoming image), the Landed Duty Cycle tracks one-to-one with the gray scale value, as shown in Table 2.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
Micromirror Landed-On/Landed-Off Duty Cycle (continued)
Table 2. Grayscale Value and Landed Duty Cycle
GRAYSCALE VALUE
LANDED DUTY CYCLE
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
0/100
10/90
20/80
30/70
40/60
50/50
60/40
70/30
80/20
90/10
100/0
32
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The DLP9000XUV DMD is controlled by the DLPC910 controller, where the DLPC910 is configured by the
program content in the DLPR910. This chipset offers streaming 1-bit binary patterns to the DMD at speeds
greater than 61 Gigabits per second (Gbps). The patterns are streamed from a customer designed processor into
the LVDS input data interface of the DLPC910 Controller.
The DLP9000XUV chipset provides solutions for many varied applications including structured light,
3D printing, video projection, and high speed lithography. The DMD is a spatial light modulator, which reflects
incoming light from an illumination source to one of two directions, with the primary direction being into a
projection or collection optic. Each application is derived primarily from the optical architecture of the system and
the format of the data being used.
9.1.1 DMD Reflectivity Characteristics
Under long term UVA illumination, many elements of optical systems can experience degradation, including
illuminators, lenses, etc. TI assumes no responsibility for DMD reflectivity performance which affects end-
equipment performance over time. Achieving the desired end-equipment reflectivity performance involves making
trade-offs between numerous component and system design parameters and validating the performance for the
end equipment prior to production. DMD reflectivity includes both micromirror surface reflectivity and DMD
window transmission. DMD reflectivity was characterized over time using 365 nm, 385 nm, and 405 nm high
power LEDs directly illuminating the DMD at various DMD array temperatures. Nominal DMD Reflectivity
characteristics over Total UV Exposure Times at maximum power densities for given wavelengths are
represented in the following figures. (Contact your local Texas Instruments representative for additional
information about power density measurements.)
Figure 16. Relative Reflectivity @ 355nm
Figure 17. Relative Reflectivity @ 365nm
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
Application Information (continued)
Figure 18. Relative Reflectivity @ 385nm
Figure 19. Relative Reflectivity @ 405nm
9.1.1.1 Design Considerations Influencing DMD Reflectivity
Optimal, long-term performance of the digital micromirror device (DMD) can be affected by various customer
selected application and design parameters. The following list identifies some of these parameters and includes
high level design recommendations that may help extend relative DMD reflectivity from time zero:
•
Illumination spectrum – use longer wavelengths for the application whenever possible while filtering or
preventing shorter wavelengths from striking the DMD
•
•
Illumination power density – use the lowest illumination power density possible for the application
DMD temperature – always operate the DMD within its array temperature specification and toward the lower
end when at all possible
•
•
Cumulative incident illumination – minimize the total hours of UV illumination exposure. In the application,
when the DMD is not actively required to steer UV light, disable the solid-state illumination or shutter the
illumination.
Micromirror landed duty cycles – during periods of system inactivity, turn off the illuminators and rapidly apply
repeating 50/50 duty cycle patterns to the DMD.
9.2 Typical Applications
High-end lithography is benefitting from the conversion from mask-based imaging to digital mask-less imaging.
Instead of stopping the lithography process to change out expensive masks, mask-less lithography offers a
continuous run of printing by changing the imaged patterns digitally without stopping the imaging process. The
programmable nature of the DMD supports real-time correction of optical and imaged surface distortions.
Figure 20 shows a system where a DLPC910 digital controller is coupled with the DLP9000XUV DMD. These
components enable a high speed digital imaging system that takes in digital images at 2560 × 1600 in resolution
at speeds of more than 61 Gbps and projects them at pattern rates nearing 15 kHz. For more information, refer
to the DLPC910 digital controller data sheet listed under Related Documentation.
9.2.1 Design Requirements
Detailed design requirements are located in the DLPC910 digital controller data sheets. Refer to the data sheets
listed under Related Documentation.
9.2.2 Detailed Design Procedure
TIDA-00570 is a TI reference design which provides detailed information to assist customers in implementing a
DLPC910 based system using the DLP9000X DMD. The reference design is also applicable to using the
DLPC910 with the DLP9000XUV DMD instead of the DLP9000X DMD. This reference material includes
reference board schematics, PCB layouts, and Bills of Materials. Layout guidelines for boards utilizing these
controllers and DMDs can also be found in the DLPC910 Controller and DLP9000X(UV) data sheets. For more
information, please refer to the individual data sheets listed under Related Documentation.
34
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Typical Applications (continued)
Illumination
Driver
Illumination
Sensor
LVDS Interface
DCLKIN (A,B,C,D), DVALID (A,B,C,D), DIN(A,B,C,D)
Row and Block Signals
ROWMD (1:0), ROWAD (10:0), BLKMD (1:0), BLKAD (3:0), RST2BLKZ
USER
Interface
DOUT(A,B,C,D)[15:0]
DCLKOUT (A,B,C,D)
APPS
FPGA
Control Signals
COMP_DATA.NS_FLIP,WDT_ENBLZ,PWR_FLOAT
SCTRL (A,B,C,D)
Status Signals
RST_ACTIVE, INIT_ACTIVE, ECP2_FINISHED
Connectivity
USB
Ethernet
RESET_ADDR (3:0)
RESET_MODE (1:0)
RESET_SEL (1:0)
JTAG(3:0)
DLP9000XUV
DLPC910
RESET_STRB
RESET_OEZ
Volatile
And
PGM(4:0)
DLPR910
Non-Volatile
Storage
RESET_IRQZ
CTRL_RSTZ
I2C
SCP BUS (3:0)
RESETZ
VLED0
VLED1
OSC
50 MHz
Power Management
Power In
Figure 20. DLP9000XUV DMD - Typical Application Schematic
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
35
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
10 Power Supply Requirements
10.1 DMD Power Supply Requirements
The following power supplies are all required to operate the DMD: VCC, VCCI, VOFFSET, VBIAS, and VRESET. VSS
must also be connected. DMD power-up and power-down sequencing is strictly controlled by the DLPC910
Controllers within their associated reference designs.
CAUTION
For reliable operation of the DMD, the following power supply sequencing
requirements must be followed. Failure to adhere to the prescribed power-up and
power-down procedures may affect device reliability. VCC, VCCI, VOFFSET, VBIAS, and
VRESET power supplies have to be coordinated during power-up and power-down
operations. VSS must also be connected. Failure to meet any of the below
requirements will result in a significant reduction in the DMD’s reliability and lifetime.
Refer to Figure 21.
10.2 DMD Power Supply Power-Up Procedure
•
During power-up, VCC and VCCI must always start and settle before VOFFSET, VBIAS, and VRESET voltages are
applied to the DMD.
•
During power-up, it is a strict requirement that the delta between VBIAS and VOFFSET must be within the
specified limit shown in Recommended Operating Conditions. During power-up, VBIAS does not have to start
after VOFFSET
.
•
•
During power-up, there is no requirement for the relative timing of VRESET with respect to VOFFSET and VBIAS
.
Power supply slew rates requirements during power-up are flexible, provided that the transient voltage levels
follow the requirements listed in Absolute Maximum Ratings, in Recommended Operating Conditions, and in
Figure 21.
•
During power-up, LVCMOS input pins shall not be driven high until after VCC and VCCI have settled at
operating voltages listed in Recommended Operating Conditions.
36
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
10.3 DMD Mirror Park Sequence (Power_Float) Requirements
For correct power down operation of the DLP9000XUV DMD, the following power down procedure must be
executed.
Prior to an anticipated power removal, assert the PWR_FLOAT signal to the DLPC910 for a minimum of 500 μs
to allow the DLPC910 to complete the power down procedure. This procedure will assure the DMD mirrors are in
the unbiased parked state. Following this procedure, the power can be safely removed.
In the event of an unanticipated power loss, the power management system must detect the input power loss,
immediately assert PWR_FLOAT to the DLPC910, and maintain all operating power levels of the DLPC910 and
the DLP9000XUV DMD for a minimum of 500 μs to allow the DLPC910 to complete the power down procedure.
Refer to the DLPC910 datasheet for more details on power down requirements.
To restart the DLPC910 and DLP9000XUV after assertion of PWR_FLOAT, the DLPC910 must be reset by
setting CTRL_RSTZ low (logic 0) for 50 ms and then back to high (logic 1), or the power to the DLPC910 must
be cycled.
10.4 DMD Power Supply Power-Down Procedure
•
During power-down, VCC and VCCI must be supplied until after VBIAS, VRESET, and VOFFSET are discharged to
within the specified limit of ground. Refer to Table 3.
•
During power-down, it is a strict requirement that the delta between VBIAS and VOFFSET must be within the
specified limit shown in Recommended Operating Conditions. During power-down, it is not mandatory to stop
driving VBIAS prior to VOFFSET
During power-down, there is no requirement for the relative timing of VRESET with respect to VOFFSET and
VBIAS
Power supply slew rates during power-down are flexible, provided that the transient voltage levels follow the
requirements listed in Absolute Maximum Ratings, in Recommended Operating Conditions, and in Figure 21.
.
•
•
•
.
During power-down, LVCMOS input pins must be less than specified in Recommended Operating Conditions.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
37
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
DMD Power Supply Power-Down Procedure (continued)
EN_BIAS, EN_OFFSET, and EN_RESET are disabled by DLP controller software or PWRDNZ signal control
VBIAS, VOFFSET, and VRESET are disabled by DLP controller software
Note 3
Power Off
VCC / VCCI
Mirror Park Sequence
RESET_OEZ
Note 6
VSS
VSS
VSS
¸ ¸
VCC / VCCI
PWRDNZ
¸ ¸
VSS
VCC / VCCI
VCC
VCCI
VSS
¸ ¸
VSS
VSS
EN_BIAS
VCC / VCCI
EN_OFFSET
¸ ¸
Note 3
EN_RESET
VSS
VBIAS
VBIAS
¸ ¸
VBIAS
VBIAS < Specification
Note 1
Note 1
∆V < Specification
Note 4
∆V < Specification
VSS
VSS
VOFFSET
VOFFSET
¸ ¸
VOFFSET < Specification
VOFFSET
Note 4
VSS
VSS
VSS
Note 5
Refer to specifications listed in Recommended Operating Conditions.
Waveforms are not to scale. Details are omitted for clarity.
VRESET < Specification
Note 4
VSS
VRESET
VRESET > Specification
VRESET
VCC
VRESET
¸ ¸
¸ ¸
LVCMOS
Inputs
VSS
VSS
VSS
VSS
Note 2
Note 2
LVDS
Inputs
¸ ¸
Figure 21. DMD Power Supply Sequencing Requirements
38
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
DMD Power Supply Power-Down Procedure (continued)
1. To prevent excess current, the supply voltage delta |VBIAS – VOFFSET| must be less than specified in
Recommended Operating Conditions. OEMs may find that the most reliable way to ensure this is to power
VOFFSET prior to VBIAS during power-up and to remove VBIAS prior to VOFFSET during power-down.
2. During power-up, the LVDS signals are less than the input differential voltage (VID) maximum specified in
Recommended Operating Conditions. During power-down, LVDS signals are less than the high level input
voltage (VIH) maximum specified in Recommended Operating Conditions.
3. When system power is interrupted, the DLPC910 controllers initiate a hardware power-down that activates
PWRDNZ and disables VBIAS, VRESET and VOFFSET after the micromirror park sequence. Software power-
down disables VBIAS, VRESET, and VOFFSET after the micromirror park sequence through software control. For
either case, enable signals EN_BIAS, EN_OFFSET, and EN_RESET are used to disable VBIAS, VOFFSET, and
VRESET, respectively.
4. Refer to Table 3.
5. Figure not to scale. Details have been omitted for clarity. Refer to Recommended Operating Conditions.
6. Refer to DMD Mirror Park Sequence (Power_Float) Requirements for details on powering down the DMD.
Table 3. DMD Power-Down Sequence Requirements
PARAMETER
MIN
MAX
4.0
UNIT
VBIAS
V
V
V
VOFFSET
VRESET
Supply voltage level during power–down sequence
4.0
–4.0
0.5
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
39
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
11 Layout
11.1 Layout Guidelines
Each chipset provides a solution for many applications including digital lithography and 3D printing. This section
provides layout guidelines for the DMD.
11.1.1 General PCB Recommendations
The PCB shall be designed to IPC2221 and IPC2222, Class 2, Type Z, at level B producibility and built to
IPC6011 and IPC6012, class 2. The PCB board thickness to be 0.062 inches ±10%, using a dielectric material
with a low loss-tangent, for example: Hitachi 679gs or equivalent.
Two-ounce copper planes are recommended in the PCB design in order to achieve needed thermal connectivity.
Refer to the digital controller data sheets listed under Related Documentation regarding DMD Interface
Considerations.
High-speed interface waveform quality and timing on the digital controllers (that is, the LVDS DMD interface) is
dependent on the following factors:
•
•
•
•
•
Total length of the interconnect system
Spacing between traces
Characteristic impedance
Etch losses
How well matched the lengths are across the interface
Thus, ensuring positive timing margin requires attention to many factors.
As an example, DMD interface system timing margin can be calculated as follows:
•
Setup Margin = (controller output setup) – (DMD input setup) – (PCB routing mismatch) – (PCB SI
degradation)
•
Hold-time Margin = (controller output hold) – (DMD input hold) – (PCB routing mismatch) – (PCB SI
degradation)
The PCB SI degradation is the signal integrity degradation due to PCB effects which includes simultaneously
switching output (SSO) noise, crosstalk, and inter-symbol-interference (ISI) noise.
DLPC910 I/O timing parameters can be found in their respective data sheets. Similarly, PCB routing mismatch
can be easily budgeted and met via controlled PCB routing. However, PCB SI degradation is not as easy to
determine.
In an attempt to minimize the signal integrity analysis that would otherwise be required, the following PCB design
guidelines provide a reference of an interconnect system that satisfies both waveform quality and timing
requirements (accounting for both PCB routing mismatch and PCB SI degradation). Deviation from these
recommendations should be confirmed with PCB signal integrity analysis or lab measurements.
11.1.2 Power Planes
Signal routing is NOT allowed on the power and ground planes. All device pin and via connections to this plane
shall use a thermal relief with a minimum of four spokes. The power plane shall clear the edge of the PCB by
0.2".
Prior to routing, vias connecting all digital ground layers (GND) should be placed around the edge of the rigid
PWB regions 0.025” from the board edges with a 0.100” spacing. It is also desirable to have all internal digital
ground (GND) planes connected together in as many places as possible. If possible, all internal ground planes
should be connected together with a minimum distance between connections of 0.5". Extra vias are not required
if there are sufficient ground vias due to normal ground connections of devices. NOTE: All signal routing and
signal vias should be inside the perimeter ring of ground vias.
Power and Ground pins of each component shall be connected to the power and ground planes with one via for
each pin. Trace lengths for component power and ground pins should be minimized (ideally, less than 0.100”).
Unused or spare device pins that are connected to power or ground may be connected together with a single via
to power or ground. Ground plane slots are NOT allowed.
Route VOFFSET, VBIAS, and VRESET as a wide trace >20 mils (wider if space allows) with 20 mils spacing.
40
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Layout Guidelines (continued)
11.1.3 LVDS Signals
The LVDS signals shall be first. Each pair of differential signals must be routed together at a constant separation
such that constant differential impedance (as in section Board Stack and Impedance Requirements) is
maintained throughout the length. Avoid sharp turns and layer switching while keeping lengths to a minimum.
The distance from one pair of differential signals to another shall be at least 2 times the distance within the pair.
11.1.4 Critical Signals
The critical signals on the board must be hand routed in the order specified below. In case of length matching
requirements, the longer signals should be routed in a serpentine fashion, keeping the number of turns to a
minimum and the turn angles no sharper than 45 degrees. Avoid routing long trace all around the PCB.
Table 4. Timing Critical Signals
GROUP
SIGNAL
CONSTRAINTS
ROUTING LAYERS
D_AP(0:15), D_AN(0:15), DCLK_AP,
DCLK_AN, SCTRL_AN, SCTRL_AP,
D_BP(0:15), D_BN(0:15), DCLK_BP,
DCLK_BN, SCTRL_BN, SCTRL_BP,
D_CP(0:15), D_CN(0:15), DCLK_CP,
DCLK_CN, SCTRL_CN, SCTRL_CP,
D_DP(0:15), D_DN(0:15), DCLK_DP,
DCLK_DN, SCTRL_DN, SCTRL_DP.
Internal signal layers. Avoid layer switching
when routing these signals.
1
Refer to Table 5 and Table 6
RESET_ADDR_(0:3),
RESET_MODE_(0:1),
RESET_OEZ,
Internal signal layers. Top and bottom as
required.
2
RESET_SEL_(0:1)
RESET_STROBE,
RESET_IRQZ.
SCP_CLK, SCP_DO,
SCP_DI, SCP_DMD_CSZ.
3
4
Any
Any
Others
No matching/length requirement
11.1.5 Flex Connector Plating
Plate all the of pad area on the top layer of the flex connection with a minimum of 35 and of maximum 50 micro-
inches of electrolytic hard gold over a minimum of 150 micro-inches of electrolytic nickel.
11.1.6 Device Placement
Unless otherwise specified, all major components should be placed on the top layer. Small components such as
ceramic, non-polarized capacitors, resistors, and resistor networks can be placed on the bottom layer. All high
frequency de-coupling capacitors for the ICs shall be placed near the parts. Distribute the capacitors evenly
around the IC and place them as close to the device’s power pins as possible (preferably with no vias). In the
case where an IC has multiple de-coupling capacitors with different values, alternate the values of those that are
side by side as much as possible and place the smaller value capacitor closer to the device.
11.1.7 Device Orientation
It is desirable to have all polarized capacitors oriented with their positive terminals in the same direction. If
polarized capacitors are oriented both horizontally and vertically, then all horizontal capacitors should be oriented
with the “+” terminal facing the same direction and likewise for the vertically oriented ones.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
41
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
11.2 Layout Example
11.2.1 Board Stack and Impedance Requirements
Refer to Figure 22 regarding guidance on the parameters.
PCB design:
Configuration:
Asymmetric dual stripline
Etch thickness (T):
1.0-oz copper (1.2 mil)
0.5-oz copper (0.6 mil)
50 Ω (±10%)
Flex etch thickness (T):
Single-ended signal impedance:
Differential signal impedance:
100 Ω (±10%)
PCB stack-up:
Reference plane 1 is assumed to be a ground plane for the proper return path.
Reference plane 2 is assumed to be the I/O power plane or ground.
Dielectric material with a low loss-tangent, for
example: Hitachi 679gs or equivalent.
(Er): 3.8 (nominal)
Signal trace distance to reference plane 1 (H1): 5.0 mil (nominal)
Signal trace distance to reference plane 2 (H2): 34.2 mil (nominal)
Figure 22. PCB Stack Geometries
42
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
Layout Example (continued)
Table 5. General PCB Routing (Applies to All Corresponding PCB Signals)
PARAMETER
APPLICATION
SINGLE-ENDED SIGNALS
DIFFERENTIAL PAIRS
UNIT
4 .4
(0.1)
4 .3
(0.1)
mil
(mm)
Escape routing in ball field
7
4.25
(0.11)
mil
(mm)
Line width (W)
PCB etch data or control
PCB etch clocks
(0.18)
7
4.25
(0.11)
mil
(mm)
(0.18)
5.75(1)
–0.15
5.75(1)
–0.15
mil
(mm)
PCB etch data or control
PCB etch clocks
N/A
N/A
N/A
N/A
Differential signal pair spacing (S)
mil
(mm)
20
(0.51)
mil
(mm)
PCB etch data or control
PCB etch clocks
Minimum differential pair-to-pair
spacing (S)
20
(0.51)
mil
(mm)
4
(0.1)
4
(0.1)
mil
(mm)
Escape routing in ball field
PCB etch data or control
PCB etch clocks
10
(0.25)
20
(0.51)
mil
(mm)
Minimum line spacing to other
signals (S)
20
(0.51)
20
(0.51)
mil
(mm)
10
–0.25
mil
(mm)
Maximum differential pair P-to-N
length mismatch
Total data
N/A
N/A
10
–0.25
mil
(mm)
Total data
(1) Spacing may vary to maintain differential impedance requirements.
Table 6. DMD Interface Specific Routing
SIGNAL GROUP LENGTH MATCHING
INTERFACE
SIGNAL GROUP
REFERENCE SIGNAL
MAX MISMATCH
UNIT
± 50
(± 1.3)
mil
(mm)
SCTRL_AN / SCTRL_AP
D_AP(15:0)/ D_AN(15:0)
DMD (LVDS)
DCLK_AP/ DCLK_AN
± 50
(± 1.3)
mil
(mm)
SCTRL_BN/ SCTRL_BP
D_BP(15:0)/ D_BN(15:0)
DMD (LVDS)
DMD (LVDS)
DMD (LVDS)
DCLK_BP/ DCLK_BN
DCLK_CP/ DCLK_CN
DCLK_DP/ DCLK_DN
± 50
(± 1.3)
mil
(mm)
SCTRL_CN/ SCTRL_CP
D_CP(15:0)/ D_CN(15:0)
± 50
(± 1.3)
mil
(mm)
SCTRL_DN/ SCTRL_DP
D_DP(15:0)/ D_DN(15:0)
Number of layer changes:
•
•
Single-ended signals: Minimize.
Differential signals: Individual differential pairs can be routed on different layers but the signals of a given pair
should not change layers.
(1)
Table 7. DMD Signal Routing Length
BUS
MIN
MAX
UNIT
DMD (LVDS)
50
375
mm
(1) Max signal routing length includes escape routing.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
43
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
Stubs: Stubs should be avoided.
Termination Requirements (DMD interface): None – The DMD receiver is differentially terminated to 100 Ω
internally.
Connector (DMD-LVDS interface bus only):
High-speed connectors that meet the following requirements should be used:
•
•
Differential crosstalk: <5%
Differential impedance: 75 to 125 Ω
Routing requirements for right-angle connectors: When using right-angle connectors, P-N pairs should be routed
in the same row to minimize delay mismatch. When using right-angle connectors, propagation delay difference
for each row should be accounted for on associated PCB etch lengths. Voltage or low frequency signals should
be routed on the outer layers. Signal trace corners shall be no sharper than 45 degrees. Adjacent signal layers
shall have the predominant traces routed orthogonal to each other.
44
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
12 Device and Documentation Support
12.1 Device Support
12.1.1 Device Nomenclature
Figure 23 provides a legend for reading the complete device name for any DLP device.
xDLP9000XUV_FLS
Package Type
Revision
Wavelength
Device Descriptor
Device Status
x œ prototype device
blank œ production device
Figure 23. Device Nomenclature
12.1.2 Device Markings
The device marking will include both human-readable information and a 2-dimensional matrix code. The human-
readable information is described in Figure 24. The 2-dimensional matrix code is an alpha-numeric character
string that contains the DMD part number, Part 1 of Serial Number, and Part 2 of Serial Number. The first
character of the DMD Serial Number (part 1) is the manufacturing year. The second character of the DMD Serial
Number (part 1) is the manufacturing month.
TI Internal Numbering
2 Dimensional Matrix Code
(DMD Part Number and
DMD Part Number
Serial Number)
YYYYYYY
DLP9000XUVFLS
GHXXXXX LLLLLLM
LLLLLL
Part 2 of Serial Number
(7 characters)
Part 1 of Serial Number
(7 characters)
TI Internal Numbering
Figure 24. DMD Markings
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
45
Product Folder Links: DLP9000XUV
DLP9000XUV
DLPS158 –DECEMBER 2019
www.ti.com
12.2 Documentation Support
12.2.1 Related Documentation
The following documents contain additional information related to the use of the DLP9000XUV:
•
•
•
DLPC910 Digital Controller Data Sheet (DLPS064)
DLPR910 Configuration PROM Data Sheet (DLPS065)
DLP9000 DLP9500 Type A Mounting Concept (DLPR014)
12.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
DLP is a registered trademark of Texas Instruments.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
13.1 Thermal Characteristics
Achieving optimal DMD performance requires proper management of the maximum DMD case temperature, the
maximum temperature of any individual micromirror in the active array and the temperature gradient between
any two points on or within the package.
Refer to Absolute Maximum Ratings and Recommended Operating Conditions regarding applicable temperature
limits.
13.2 Package Thermal Resistance
The DMD is designed to conduct the absorbed and dissipated heat back to the series FLS package where it can
be removed by an appropriate thermal management system. The thermal management system must be capable
of maintaining the package within the specified operational temperatures at the thermal test point locations (refer
to Figure 15 or Micromirror Array Temperature Calculation). The total heat load on the DMD is typically driven by
the incident light absorbed by the active area; although other contributions can include light energy absorbed by
the window aperture, electrical power dissipation of the array, and parasitic heating. For the thermal resistance,
refer to Thermal Information.
13.3 Case Temperature
The temperature of the DMD case can be measured directly. For consistency, a thermal test point location is
defined as shown in Figure 15 and Micromirror Array Temperature Calculation.
46
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
Product Folder Links: DLP9000XUV
DLP9000XUV
www.ti.com
DLPS158 –DECEMBER 2019
13.4 Package Option Addendum
13.4.1 Packaging Information
Package
Package
Drawing
Package
Qty
(1)
(2)
(3)
Orderable Device
Status
Pins
Eco Plan
Lead/Ball Finish MSL Peak Temp
Op Temp (°C)
Device Marking(4)(5)
Type
CLGA
CLGA
xDLP9000XUVFLS
DLP9000XUVFLS
PREVIEW
PREVIEW
FLS
FLS
355
355
1
1
RoHS & Green
RoHS & Green
NI-PD-AU
NI-PD-AU
N / A for Pkg Type
N / A for Pkg Type
20°C to 30°C
20°C to 30°C
See Data Sheet
See Data Sheet
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PRE_PROD Unannounced device, not in production, not available for mass market, nor on the web, samples not available.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
space
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest
availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the
requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified
lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used
between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by
weight in homogeneous material)
space
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
space
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device
space
(5) Multiple Device markings will be inside parentheses. Only on Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer: The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief
on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third
parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Copyright © 2019, Texas Instruments Incorporated
Submit Documentation Feedback
47
Product Folder Links: DLP9000XUV
PACKAGE OPTION ADDENDUM
www.ti.com
9-Sep-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
DLP9000XUVFLS
ACTIVE
CLGA
FLS
355
12
RoHS & Green
NI-PD-AU
N / A for Pkg Type
20 to 30
Samples
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Sep-2022
TRAY
L - Outer tray length without tabs
KO -
Outer
tray
height
W -
Outer
tray
width
Text
P1 - Tray unit pocket pitch
CW - Measurement for tray edge (Y direction) to corner pocket center
CL - Measurement for tray edge (X direction) to corner pocket center
Chamfer on Tray corner indicates Pin 1 orientation of packed units.
*All dimensions are nominal
Device
Package Package Pins SPQ Unit array
Max
matrix temperature
(°C)
L (mm)
W
K0
P1
CL
CW
Name
Type
(mm) (µm) (mm) (mm) (mm)
DLP9000XUVFLS
FLS
CLGA
355
12
4 x 5
60
254.76 221.74 48590 48.59 30.22 31.98
Pack Materials-Page 1
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明