DRV777PWR [TI]
7- bit Integrated Motor and Relay Driver; 7位集成电机和继电器驱动器型号: | DRV777PWR |
厂家: | TEXAS INSTRUMENTS |
描述: | 7- bit Integrated Motor and Relay Driver |
文件: | 总17页 (文件大小:905K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DRV777
www.ti.com
SLRS062 –DECEMBER 2012
7- bit Integrated Motor and Relay Driver
Check for Samples: DRV777
1
FEATURES
Functional Diagram
•
•
•
Supports up to 20V Output Pull-up Voltage
–40°C to 125°C Operating Temperature Range
OUT1
16
IN1
IN2
1
2
3
4
5
6
15 OUT2
Supports Wide Range of Stepper Motors, DC
Motors, Relays, and Inductive Coils
14
OUT3
IN3
IN4
OUT4
OUT5
13
12
•
Low Output VOL of 0.4V (Typical) With
IN5
IN6
–
140mA Current Sink per Channel at 5.0V
Logic Input(1)
11
10
OUT6
OUT7
COM
7
8
IN7
–
1A Current Output when all 7 Channels
Tied in Parallel(1)
9
GND
DRV777 TSSOP/SOIC
•
•
•
•
Compatible to 1.8V, 3.3V and 5.0V Micro-
controllers and Logic Interface
DESCRIPTION
DRV777 motor driver features
Internal Free-wheeling Diodes for Inductive
Kick-back Protection
7
low output
impedance drivers that minimize on-chip power
dissipation. DRV777 supports 1.8V to 5V CMOS logic
input interface thus making it compatible to a wide
range of micro-controllers and other logic interfaces.
DRV777 features an improved input interface that
minimizes the input DC current drawn from the
external drivers. Device also features an input RC
snubber that greatly improves its performance in
noisy operating conditions. All channel inputs feature
an internal input pull-down resistor thus allowing input
logic to be tri-stated. DRV777 also supports other
logic input levels, e.g. TTL and 1.8V; see typical
characteristics section for details.
Input Pull-down Resistors Allows Tri-stating
the Input Driver
Input RC-Snubber to Eliminate Spurious
Operation in Noisy Environment
•
•
•
Low Input and Output Leakage Currents
Easy to use Parallel Interface
ESD Protection Exceeds JESD 22
–
2kV HBM, 500V CDM
•
(1)
Available in 16-pin SOIC and TSSOP Packages
Total current sink may be limited by the internal junction
temperature, absolute maximum current levels etc - refer to
the Electrical Specifications section for details.
As shown in the Functional Diagram, each output of
the DRV777 features an internal free-wheeling diode
connected in a common-cathode configuration at the
COM pin.
APPLICATIONS
•
•
•
•
•
•
Unipolar Stepper Motor Drivers
Relay and Inductive Load Drivers
Solenoid Drivers
Device provides flexibility of increasing current sink
capability through combining several adjacent
channels in parallel. Under typical conditions DRV777
can support up to 1.0A of load current when all 7-
channels are connected in parallel. DRV777 is
available in 16-pin SOIC and 16-pin TSSOP
packages.
Lamp and LED Displays
Logic Level Shifter
General Low-Side Switch Applications
Table 1. DRV777 Function Table(1)
INPUT (IN1 – IN7)
OUTPUT (OUT1–OUT7)
L
H
Z
H+(2)
L
H+(2)
(1) L = Low-level (GND); H= High-level; Z= High-impedance;
(2) H+ = Pull-up-level
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
DRV777
SLRS062 –DECEMBER 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION(1)
TJ
PART NUMBER
DRV777DR
PACKAGE
TOP-SIDE MARKING
DRV777
16-Pin SOIC
Reel of 2500
Reel of 2000
–40°C to 125°C
DRV777PWR
16-Pin TSSOP
DRV777
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
DEVICE INFORMATION
COM
1
2
3
16
15
14
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
COM
IN1
IN2
IN3
OUTX
RC Filter/Snubber
16-Pin
SOIC/TSSOP
4
5
6
7
8
13
12
11
10
9
RIN=3kQ
IN4
INX
NFET
IN5
Pull-down
300kQ
IN6
CIN= 9pF
ESD
ESD
IN7
GND
Figure 1. DRV777 PINOUT
Figure 2. Channel Block Diagram
DRV777 PIN DESCRIPTION
NAME
PIN NUMBER
DESCRIPTION
16-SOIC
16-TSSOP
IN1 – IN7
GND
1–7
8
1–7
8
Logic Input Pins IN1 through IN7
Ground Reference Pin
COM
9
9
Internal Free-Wheeling Diode Common Cathode Pin
Channel Output Pins OUT7 through OUT1
OUT7 – OUT1
10–16
10–16
2
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: DRV777
DRV777
www.ti.com
SLRS062 –DECEMBER 2012
ABSOLUTE MAXIMUM RATINGS(1)
Specified at TJ = –40°C to 125°C unless otherwise noted.
VALUE
UNIT
MIN
MAX
5.5
20
VIN
Pins IN1- IN7 to GND voltage
–0.3
V
V
VOUT
VCOM
Pins OUT1 – OUT7 to GND voltage
Pin COM to GND voltage
20
V
Max GND-pin continuous current (100ºC < TJ < +125°C)
Max GND-pin continuous current (TJ < +100°C)
700
1.0
0.86
0.68
2
mA
A
IGND
16 Pin - SOIC
16 Pin - TSSOP
W
W
kV
V
PD
Total device power dissipation at TA = 85°C
ESD Rating – HBM
ESD
ESD Rating – CDM
500
150
150
TJ
Operating virtual junction temperature
Storage temperature range
–55
–55
°C
°C
Tstg
(1) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these conditions is not implied. Exposure to absolute-maximum-rated conditions for
extended periods may affect device reliability.
DISSIPATION RATINGS(1)(2)
(3)
BOARD
PACKAGE
θJC
θJA
DERATING
FACTOR
TA < 25°C
TA = 70°C
TA = 85°C
TA = 105°C
ABOVE TA
25ºC
=
High-K
High-K
16-Pin SOIC
46°C/W
49°C/W
75°C/W
95°C/W
13.33 mW/ºC
10.44 mW/ºC
1.66 W
1.31 W
1.06 W
0.84 W
0.86 W
0.68 W
0.59 W
0.47 W
16-Pin TSSOP
(1) Maximum dissipation values for retaining device junction temperature of 150°C
(2) Refer to TI’s design support web page at www.ti.com/thermal for improving device thermal performance
(3) Operating at the absolute TJ-max of 150°C can affect reliability– for higher reliability it is recommended to ensure TJ < 125°C
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
PARAMETER
Channel off-state output pull-up voltage
COM pin voltage
MIN
TYP
MAX
16
UNIT
V
VOUT
VCOM
16
V
VINx = 3.3V
VINx = 5.0V
100(1)
140(1)
125
IOUT(ON)
TJ
Per channel continuous sink current
Operating junction temperature
mA
ºC
–40
(1) 1) Refer to ABSOLUTE MAXIMUM RATINGS for TJ dependent absolute maximum GND-pin current
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: DRV777
DRV777
SLRS062 –DECEMBER 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
Specified over the recommended junction temperature range TJ = –40°C to 125°C and over recommended operating
conditions unless otherwise noted. Typical values are at TJ = 25°C.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUTS IN1 THROUGH IN7 PARAMETERS
VI(ON)
IN1–IN7 logic high input voltage
Vpull-up = 3.3 V, Rpull-up = 1 kΩ, IOUTX = 3.2 mA
1.65
V
V
Vpull-up = 3.3 V, Rpull-up = 1 kΩ,
(IOUTX < 20 µA)
VI(OFF)
IN1–IN7 logic low input voltage
0.4
12
0.6
II(ON)
IN1–IN7 ON state input current
IN1–IN7 OFF state input leakage
Vpull-up = 3.3 V, VINx = 3.3 V
Vpull-up = 3.3 V, VINx = 0 V
25
uA
nA
II(OFF)
250
OUTPUTS OUT1 THROUGH OUT7 PARAMETERS
VINX = 3.3 V, IOUTX = 100 mA
VINX = 5.0 V, IOUTX = 140 mA
VINX = 3.3 V, VOUTX = 0.4 V
VINX = 5.0 V, VOUTX = 0.4 V
VINX = 0 V, VOUTX = VCOM = 16 V
0.36
0.40
100
140
0.5
0.49
VOL
OUT1–OUT7 low-level output voltage
V
80
95
OUT1–OUT7 ON-state continuous
current(1) (2) at VOUTX = 0.4V
IOUT(ON)
mA
µA
IOUT(OFF)(ICEX)
OUT1–OUT7 OFF-state leakage current
SWITCHING PARAMETERS(3)(4)
tPHL OUT1–OUT7 logic high propagation delay VINX = 3.3V, Vpull-up = 12 V, Rpull-up = 1 kΩ
tPLH
50
70
ns
ns
OUT1–OUT7 logic low propagation delay
Channel to Channel delay
VINX = 3.3V, Vpull-up = 12 V, Rpull-up = 1 kΩ
121
140
Over recommended operating conditions and
with same test conditions on channels.
t CHANNEL
15
50
ns
RPD
ζ
IN1–IN7 input pull-down Resistance
IN1–IN7 Input filter time constant
OUT1–OUT7 output capacitance
210k
300k
9
390k
Ω
ns
pF
COUT
VINX = 3.3 V, VOUTX = 0.4 V
15
FREE-WHEELING DIODE PARAMETERS(5)(4)
VF
Forward voltage drop
IF-peak = 140 mA, VF = VOUTx – VCOM
1.2
V
IF-peak
Diode peak forward current
140
mA
(1) The typical continuous current rating is limited by VOL= 0.4V. Whereas, absolute maximum operating continuous current may be limited
by the Thermal Performance parameters listed in the Dissipation Rating Table and other Reliability parameters listed in the
Recommended Operating Conditions Table.
(2) Refer to the Absolute Maximum Ratings Table for TJ dependent absolute maximum GND-pin current.
(3) Rise and Fall propagation delays, tPHL and tPLH, are measured between 50% values of the input and the corresponding output signal
amplitude transition.
(4) Guaranteed by design only. Validated during qualification. Not measured in production testing.
(5) Not rated for continuous current operation – for higher reliability use an external freewheeling diode for inductive loads resulting in more
than specified maximum free-wheeling. diode peak current across various temperature conditions
4
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: DRV777
DRV777
www.ti.com
SLRS062 –DECEMBER 2012
APPLICATION INFORMATION
TTL and other Logic Inputs
DRV777 input interface is specified for standard 1.8V, 3V and 5V CMOS logic interface. Refer to Figure 8 and
Figure 9 to establish VOL and the corresponding typical load current levels for various input voltage ranges.
Application Information section shows an implementation to drive 1.8V relays using DRV777.
Input RC Snubber
DRV777 features an input RC snubber that helps prevent spurious switching in noisy environment. Connect an
external 1kΩ to 5kΩ resistor in series with the input to further enhance DRV777’s noise tolerance.
High-impedance Input Drivers
DRV777 features a 300kΩ input pull-down resistor. The presence of this resistor allows the input drivers to be tri-
stated. When a high-impedance driver is connected to a channel input the DRV777 detects the channel input as
a low level input and remains in the OFF position. The input RC snubber helps improve noise tolerance when
input drivers are in the high-impedance state.
On-chip Power Dissipation
Use the below equation to calculate DRV777 on-chip power dissipation PD:
N
V
´ILi
P = å
D
OLi
i=1
Where:
N is the number of channels active together.
VOLi is the OUTi pin voltage for the load current ILi.
(1)
Thermal Reliability
It is recommended to limit DRV777 IC’s die junction temperature to less than 125°C. The IC junction temperature
is directly proportional to the on-chip power dissipation. Use the following equation to calculate the maximum
allowable on-chip power dissipation for a target IC junction temperature:
T
J(MAX) - TA
(
)
PD(MAX)
=
qJA
Where:
TJ(MAX) is the target maximum junction temperature.
TA is the operating ambient temperature.
θJA is the package junction to ambient thermal resistance.
(2)
Improving Package Thermal Performance
The package θJA value under standard conditions on a High-K board is listed in the DISSIPATION RATINGS. θJA
value depends on the PC board layout. An external heat sink and/or a cooling mechanism, like a cold air fan, can
help reduce θJA and thus improve device thermal capabilities. Refer to TI’s design support web page at
www.ti.com/thermal for a general guidance on improving device thermal performance.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: DRV777
DRV777
SLRS062 –DECEMBER 2012
www.ti.com
Application Examples
One Amp Unipolar DC Motor Driver
An implementation of DRV777 for driving a uniploar DC motor is shown in Figure 3. With all of the channels tied
together and the input being driven at 5V, the driver can sink 1A of current. With a VOL of 0.4V this creates a
driver with 400mΩ. The input snubber circuitry is great for PWM applications that need high noise immunity.
These two features make DRV777 an ideal choice for power efficient high duty cycle motor driving applications.
Logic Input
DRV777
(5V)
VSUP
IN1
IN2
IN3
IN4
IN5
IN6
IN7
GND
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
COM
+
M
_
VSUP
Figure 3. DRV777 as a DC Motor Driver
6
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: DRV777
DRV777
www.ti.com
SLRS062 –DECEMBER 2012
Unipolar Stepper Motor Driver
Figure 4 shows an implementation of DRV777 for driving a uniploar stepper motor. The unconnected input
channels can be used for other functions. When an input pin is left open the internal 300kΩ pull down resistor
pulls the respective input pin to GND potential. For higher noise immunity use an external short across an
unconnected input and GND pins.
Motor
Motor Supply (Up to 8V)
VSUP
Motor Control Pulses
(3V to 5V)
DRV777
IN1
IN2
IN3
IN4
IN5
IN6
IN7
GND
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
COM
Phase_A
Phase_C
Phase_B
Phase_D
VSUP
Figure 4. DRV777 as a Stepper Motor Driver
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: DRV777
DRV777
SLRS062 –DECEMBER 2012
www.ti.com
Multi-Purpose Sink Driver
When configured as per Figure 5 DRV777 can be used as a multi-purpose driver. The output channels can be
tied together to sink more current. DRV777 can easily drive motors, relays & LEDs with little power dissipation.
The COM pin must be tied to the supply of whichever inductive load is to be protected by the free-wheeling
diode.
VSUP
Logic Inputs
(1.8V to 5V)
+
DRV777
VSUP
M
IN1
IN2
IN3
IN4
IN5
IN6
IN7
GND
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
COM
_
IN1 NOR IN2 NOR IN3
VSUP
Figure 5. DRV777 Multi-Purpose Sink Driver Application
8
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: DRV777
DRV777
www.ti.com
SLRS062 –DECEMBER 2012
1.8V Relay Driver
To drive lower voltage relays, like 1.8V, connect two or more adjacent channels in parallel as shown in Figure 6.
Connecting several channels in parallel lowers the channel output resistance and thus minimizes VOL for a fixed
current. DRV777 can be used for driving 3V, 5V and 12V relays with similar implementation.
VSUP
1.8V Relays
DRV777
IN1
IN2
IN3
IN4
IN5
IN6
IN7
GND
OUT1
OUT2
OUT3
OUT4
OUT5
OUT6
OUT7
COM
1.8V Logic
1.8V Logic
1.8V Logic
VSUP
Figure 6. DRV777 Driving 1.8V Relays
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: DRV777
DRV777
SLRS062 –DECEMBER 2012
www.ti.com
TYPICAL CHARACTERISTICS
TA = +25ºC
Figure 7. Load Current 1-Channel; VOL=0.4V
Figure 8. Load Current 7-Channels in parallel; VOL=0.4V
Figure 9. Freewheeling Diode VF versus IF
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Links: DRV777
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jan-2013
PACKAGING INFORMATION
Orderable Device
DRV777DR
Status Package Type Package Pins Package Qty
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
Top-Side Markings
Samples
Drawing
(1)
(2)
(3)
(4)
ACTIVE
SOIC
D
16
16
2500
2000
Green (RoHS
& no Sb/Br)
CU SN
CU SN
Level-1-260C-UNLIM
DRV777PWR
ACTIVE
TSSOP
PW
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 125
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
DRV777PWR
TSSOP
PW
16
2000
330.0
12.4
7.0
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
TSSOP PW 16
SPQ
Length (mm) Width (mm) Height (mm)
364.0 364.0 27.0
DRV777PWR
2000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明