DRV8832DRCT [TI]
LOW-VOLTAGE MOTOR DRIVER IC; 低压马达驱动器IC![DRV8832DRCT](http://pdffile.icpdf.com/pdf1/p00173/img/icpdf/DRV88_969818_icpdf.jpg)
型号: | DRV8832DRCT |
厂家: | ![]() |
描述: | LOW-VOLTAGE MOTOR DRIVER IC |
文件: | 总19页 (文件大小:785K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
DRV8832
www.ti.com
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
LOW-VOLTAGE MOTOR DRIVER IC
Check for Samples: DRV8832
1
FEATURES
2
•
H-Bridge Voltage-Controlled Motor Driver
•
•
Fault Output
Thermally Enhanced Surface Mount Packages
–
–
–
Drives DC Motor, One Winding of a Stepper
Motor, or Other Actuators/Loads
APPLICATIONS
Efficient PWM Voltage Control for Constant
Motor Speed With Varying Supply Voltages
•
Battery-Powered:
Low MOSFET On-Resistance:
–
–
–
–
–
Printers
Toys
HS + LS 450 mΩ
•
•
1-A Maximum DC/RMS or Peak Drive Current
Robotics
Cameras
Phones
2.75-V to 6.8-V Operating Supply Voltage
Range
•
•
•
300-nA (Typical) Sleep Mode Current
Reference Voltage Output
Current Limit Circuit
•
Small Actuators, Pumps, etc.
DESCRIPTION
The DRV8832 provides an integrated motor driver solution for battery-powered toys, printers, and other
low-voltage or battery-powered motion control applications. The device has one H-bridge driver, and can drive
one DC motor or one winding of a stepper motor, as well as other loads like solenoids. The output driver block
consists of N-channel and P-channel power MOSFET’s configured as an H-bridge to drive the motor winding.
Provided with sufficient PCB heatsinking, the DRV8832 can supply up to 1-A of DC/RMS or peak output current.
It operates on power supply voltages from 2.75 V to 6.8 V.
To maintain constant motor speed over varying battery voltages while maintaining long battery life, a PWM
voltage regulation method is provided. An input pin allows programming of the regulated voltage. A built-in
voltage reference output is also provided.
Internal protection functions are provided for over current protection, short circuit protection, under voltage
lockout and overtemperature protection.
The DRV8832 also provides a current limit function to regulate the motor current during conditions like motor
startup or stall, as well as a fault output pin to signal a host processor of a fault condition.
The DRV8832 is available in tiny 3-mm x 3-mm 10-pin MSOP and WSON packages with PowerPAD™
(Eco-friendly: RoHS & no Sb/Br).
ORDERING INFORMATION(1)
ORDERABLE PART
NUMBER
TOP-SIDE
MARKING
PACKAGE(2)
PowerPAD™ (MSOP) - DGQ
Reel of 2500
Tube of 80
DRV8832DGQR
DRV8832DGQ
DRV8832DRCR
DRV8832DRCT
8832
8832
8832
8832
Reel of 3000
Reel of 250
PowerPAD™ (WSON) - DRC
(1) For the most current packaging and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
(2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2012, Texas Instruments Incorporated
DRV8832
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
DEVICE INFORMATION
Functional Block Diagram
Battery
VCC
VCC
VCC
OCP
-
Integ.
Comp
Gate
Drive
OUT1
+
Ref
VREF
VSET
DCM
VCC
Logic
IN1
IN2
OCP
Gate
Drive
OUT2
Over-
Temp
Osc
FAULTn
Current
Sense
ISENSE
GND
2
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): DRV8832
DRV8832
www.ti.com
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
Table 1. TERMINAL FUNCTIONS
EXTERNAL COMPONENTS
OR CONNECTIONS
NAME
GND
VCC
PIN
5
I/O(1)
DESCRIPTION
Device ground
-
-
Bypass to GND with a 0.1-μF (minimum)
ceramic capacitor.
4
Device and motor supply
IN1
IN2
9
10
8
I
I
Bridge A input 1
Logic high sets OUT1 high
Bridge A input 2
Logic high sets OUT2 high
VREF
VSET
O
I
Reference voltage output
Voltage set input
Reference voltage output
7
Input voltage sets output regulation voltage
Open-drain output driven low if fault condition
present
FAULTn
6
OD
Fault output
OUT1
OUT2
3
1
O
O
Bridge output 1
Bridge output 2
Connect to motor winding
Connect to motor winding
Connect current sense resistor to GND.
Resistor value sets current limit level.
ISENSE
2
IO
Current sense resistor
(1) Directions: I = input, O = output, OZ = tri-state output, OD = open-drain output, IO = input/output
DGQ OR DRC PACKAGE
(TOP VIEW)
1
OUT2
ISENSE
OUT1
10
9
IN2
IN1
VREF
VSET
2
3
4
GND
(PPAD)
8
7
VCC
5
6
GND
FAULTn
ABSOLUTE MAXIMUM RATINGS(1)(2)
VALUE
–0.3 to 7
–0.5 to 7
UNIT
VCC
Power supply voltage range
V
V
A
A
Input pin voltage range
Peak motor drive output current(3)
Continuous motor drive output current(3)
Continuous total power dissipation
Operating virtual junction temperature range
Storage temperature range
Internally limited
1
See Dissipation Ratings table
TJ
–40 to 150
–60 to 150
°C
°C
Tstg
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
(3) Power dissipation and thermal limits must be observed.
Copyright © 2010–2012, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): DRV8832
DRV8832
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
www.ti.com
UNITS
THERMAL INFORMATION
DRV8832
DGQ
10 PINS
69.3
DRV8832
DRC
10 PINS
50.2
THERMAL METRIC(1)
θJA
Junction-to-ambient thermal resistance(2)
θJCtop
θJB
Junction-to-case (top) thermal resistance(3)
Junction-to-board thermal resistance(4)
Junction-to-top characterization parameter(5)
Junction-to-board characterization parameter(6)
Junction-to-case (bottom) thermal resistance(7)
63.5
78.4
51.6
18.8
°C/W
ψJT
1.5
1.1
ψJB
23.2
17.9
θJCbot
9.5
5.1
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
(3) The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific
JEDEC-standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
(4) The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
(5) The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7).
(6) The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7).
(7) The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific
JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
2.75
0
NOM
MAX
6.8
1
UNIT
V
VCC
IOUT
Motor power supply voltage range
Continuous or peak H-bridge output current(1)
A
(1) Power dissipation and thermal limits must be observed.
4
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): DRV8832
DRV8832
www.ti.com
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
ELECTRICAL CHARACTERISTICS
VCC = 2.75 V to 6.8 V, TA = -40°C to 85°C (unless otherwise noted)
PARAMETER
POWER SUPPLIES
TEST CONDITIONS
MIN
TYP
MAX
UNIT
IVCC
VCC operating supply current
VCC = 5 V
1.4
0.3
2
1
mA
IVCCQ
VCC sleep mode supply current VCC = 5 V, TA = 25°C
μA
VCC rising
VCC falling
2.575
2.47
2.75
VCC undervoltage lockout
voltage
VUVLO
V
LOGIC-LEVEL INPUTS
VIL
VIH
VHYS
IIL
Input low voltage
0.25 x VCC
-10
0.38 x VCC
0.46 x VCC
0.08 x VCC
V
V
Input high voltage
Input hysteresis
Input low current
Input high current
0.5 x VCC
V
VIN = 0
10
50
μA
μA
IIH
VIN = 3.3 V
LOGIC-LEVEL OUTPUTS (FAULTn)
VOL Output low voltage
H-BRIDGE FETS
VCC = 5 V, IOL = 4 mA(1)
0.5
V
VCC = 5 V, I O = 0.8 A, TJ = 85°C
VCC = 5 V, I O = 0.8 A, TJ = 25°C
VCC = 5 V, I O = 0.8 A, TJ = 85°C
VCC = 5 V, I O = 0.8 A, TJ = 25°C
290
250
230
200
400
320
20
RDS(ON)
HS FET on resistance
mΩ
RDS(ON)
IOFF
LS FET on resistance
mΩ
μA
Off-state leakage current
–20
MOTOR DRIVER
tR
Rise time
VCC = 3 V, load = 4 Ω
VCC = 3 V, load = 4 Ω
50
50
300
300
ns
ns
tF
Fall time
fSW
Internal PWM frequency
44.5
kHz
PROTECTION CIRCUITS
IOCP
tOCP
TTSD
Overcurrent protection trip level
1.3
150
3
180
A
OCP deglitch time
2
μs
°C
Thermal shutdown temperature
Die temperature(1)
160
VOLTAGE CONTROL
VREF
Reference output voltage
1.235
1.285
1.335
V
VCC = 3.3 V to 6 V, VOUT = 3 V(1)
IOUT = 500 mA
ΔVLINE
Line regulation
Load regulation
±1
%
VCC = 5 V, VOUT = 3 V
ΔVLOAD
±1
%
IOUT = 200 mA to 800 mA(1)
CURRENT LIMIT
VILIM Current limit sense voltage
tILIM
160
0
200
275
240
1
mV
ms
Current limit fault deglitch time
Current limit set resistance
(external resistor value)
RISEN
Ω
(1) Not production tested.
Copyright © 2010–2012, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): DRV8832
DRV8832
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
www.ti.com
TYPICAL PERFORMANCE GRAPHS
EFFICIENCY
vs
LOAD CURRENT
(VIN = 5 V, VOUT = 3 V)
100%
95%
90%
85%
80%
75%
70%
65%
60%
55%
50%
0.2
0.4
0.6
0.8
LOAD - A
Figure 1.
EFFICIENCY
vs
OUTPUT VOLTAGE
(VIN = 5 V, IOUT = 500 mA)
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
0%
Linear Regulator
DRV8832
0.5
1.5
2.5
3.5
VOUT - V
Figure 2.
4.5
5.5
FUNCTIONAL DESCRIPTION
PWM Motor Driver
The DRV8832 contains an H-bridge motor driver with PWM voltage-control circuitry with current limit circuitry. A
block diagram of the motor control circuitry is shown below.
6
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): DRV8832
DRV8832
www.ti.com
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
VCC
VCC
OCP
IN1
OUT1
Pre-
drive
IN2
PWM
DCM
OUT2
+
VSET
COMP
-
OCP
DIFF
/4
Integrator
ISEN
ITRIP
+
COMP
-
REF
Figure 3. Motor Control Circuitry
Bridge Control
The IN1 and IN2 control bits in the serial interface register enable the H-bridge outputs. The following table
shows the logic:
Table 2. H-Bridge Logic
IN1
0
IN2
0
OUT1
OUT2
Function
Standby/coast
Reverse
Z
L
Z
H
L
0
1
1
0
H
H
Forward
1
1
H
Brake
When both bits are zero, the output drivers are disabled and the device is placed into a low-power shutdown
state. The current limit fault condition (if present) is also cleared. Note that when transitioning from either brake
or standby mode to forward or reverse, the voltage control PWM starts at zero duty cycle. The duty cycle slowly
ramps up to the commanded voltage. This can take up to 12 ms to go from standby to 100% duty cycle. Because
of this, high-speed PWM signals cannot be applied to the IN1 and IN2 pins. To control motor speed, use the
VSET pin as described below.
Voltage Regulation
The DRV8832 provides the ability to regulate the voltage applied to the motor winding. This feature allows
constant motor speed to be maintained even when operating from a varying supply voltage such as a
discharging battery.
The DRV8832 uses a pulse-width modulation (PWM) technique instead of a linear circuit to minimize current
consumption and maximize battery life.
The circuit monitors the voltage difference between the output pins and integrates it, to get an average DC
voltage value. This voltage is divided by 4 and compared to the VSET pin voltage. If the averaged output voltage
(divided by 4) is lower than VSET, the duty cycle of the PWM output is increased; if the averaged output voltage
(divided by 4) is higher than VSET, the duty cycle is decreased.
Copyright © 2010–2012, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): DRV8832
DRV8832
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
www.ti.com
During PWM regulation, the H-bridge is enabled to drive current through the motor winding during the PWM on
time. This is shown in the diagram below as case 1. The current flow direction shown indicates the state when
IN1 is high and IN2 is low.
Note that if the programmed output voltage is greater than the supply voltage, the device will operate at 100%
duty cycle and the voltage regulation feature will be disabled. In this mode the device behaves as a conventional
H-bridge driver.
During the PWM off time, winding current is re-circulated by enabling both of the high-side FETs in the bridge.
This is shown as case 2 below.
VCC
2
1
Shown with
IN1=1, IN2=0
OUT1
OUT2
1
2
PWM on
PWM off
Figure 4. Voltage Regulation
Reference Output
The DRV8832 includes a reference voltage output that can be used to set the motor voltage. Typically for a
constant-speed application, VSET is driven from VREF through a resistor divider to provide a voltage equal to
1/4 the desired motor drive voltage.
For example, if VREF is connected directly to VSET, the voltage will be regulated at 5.14 V. If the desired motor
voltage is 3 V, VREF should be 0.75 V. This can be obtained with a voltage divider using 53 kΩ from VREF to
VSET, and 75 kΩ from VSET to GND.
8
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): DRV8832
DRV8832
www.ti.com
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
Current Limit
A current limit circuit is provided to protect the system in the event of an overcurrent condition, such as what
would be encountered if driving a DC motor at start-up or with an abnormal mechanical load (stall condition).
The motor current is sensed by monitoring the voltage across an external sense resistor. When the voltage
exceeds a reference voltage of 200 mV for more than approximately 3 µs, the PWM duty cycle is reduced to limit
the current through the motor to this value. This current limit allows for starting the motor while controlling the
current.
If the current limit condition persists for some time, it is likely that a fault condition has been encountered, such
as the motor being run into a stop or a stalled condition. An overcurrent event must persist for approximately
275 ms before the fault is registered. After approximately 275 ms, a fault signaled to the host by driving the
FAULTn signal low. Operation of the motor driver will continue.
The current limit fault condition is cleared by taking both IN1 and IN2 low to disable the motor current, or by
removing and re-applying power to the device.
The resistor used to set the current limit must be less than 1 Ω. Its value may be calculated as follows:
200 mV
RISENSE =
ILIMIT
(1)
Where:
RISENSE is the current sense resistor value.
ILIMIT is the desired current limit (in mA).
If the current limit feature is not needed, the ISENSE pin may be directly connected to ground.
Protection Circuits
The DRV8832 is fully protected against undervoltage, overcurrent and overtemperature events.
Overcurrent Protection (OCP)
An analog current limit circuit on each FET limits the current through the FET by removing the gate drive. If this
analog current limit persists for longer than the OCP time, all FETs in the H-bridge will be disabled, and the
FAULTn signal will be driven low. The device will remain disabled until VCC is removed and re-applied.
Overcurrent conditions are sensed independently on both high and low side devices. A short to ground, supply,
or across the motor winding will all result in an overcurrent shutdown. Note that OCP is independent of the
current limit function, which is typically set to engage at a lower current level; the OCP function is intended to
prevent damage to the device under abnormal (e.g., short-circuit) conditions.
Thermal Shutdown (TSD)
If the die temperature exceeds safe limits, all FETs in the H-bridge will be disabled, the FAULTn signal will be
driven low, and the FAULT and OTS bits in the serial interface register will be set. Once the die temperature has
fallen to a safe level operation will automatically resume.
Undervoltage Lockout (UVLO)
If at any time the voltage on the VCC pins falls below the undervoltage lockout threshold voltage, all circuitry in
the device will be disabled, the FAULTn signal will be driven low, and internal logic will be reset. Operation will
resume when VCC rises above the UVLO threshold.
Copyright © 2010–2012, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): DRV8832
DRV8832
SLVSAB3F –MAY 2010–REVISED FEBRUARY 2012
www.ti.com
THERMAL INFORMATION
Thermal Protection
The DRV8832 has thermal shutdown (TSD) as described above. If the die temperature exceeds approximately
160°C, the device will be disabled until the temperature drops to a safe level.
Any tendency of the device to enter TSD is an indication of either excessive power dissipation, insufficient
heatsinking, or too high an ambient temperature.
Power Dissipation
Power dissipation in the DRV8832 is dominated by the power dissipated in the output FET resistance, or RDS(ON)
.
Average power dissipation when running a stepper motor can be roughly estimated by Equation 2.
2
· ·
PTOT = 2 RDS(ON) (IOUT(RMS)
)
(2)
where PTOT is the total power dissipation, RDS(ON) is the resistance of each FET, and IOUT(RMS) is the RMS output
current being applied to each winding. IOUT(RMS) is equal to the approximately 0.7x the full-scale output current
setting. The factor of 2 comes from the fact that at any instant two FETs are conducting winding current for each
winding (one high-side and one low-side).
The maximum amount of power that can be dissipated in the device is dependent on ambient temperature and
heatsinking.
Note that RDS(ON) increases with temperature, so as the device heats, the power dissipation increases. This must
be taken into consideration when sizing the heatsink.
Heatsinking
The PowerPAD™ package uses an exposed pad to remove heat from the device. For proper operation, this pad
must be thermally connected to copper on the PCB to dissipate heat. On a multi-layer PCB with a ground plane,
this can be accomplished by adding a number of vias to connect the thermal pad to the ground plane. On PCBs
without internal planes, copper area can be added on either side of the PCB to dissipate heat. If the copper area
is on the opposite side of the PCB from the device, thermal vias are used to transfer the heat between top and
bottom layers.
For details about how to design the PCB, refer to TI application report SLMA002, " PowerPAD™ Thermally
Enhanced Package" and TI application brief SLMA004, " PowerPAD™ Made Easy", available at www.ti.com.
In general, the more copper area that can be provided, the more power can be dissipated.
10
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): DRV8832
PACKAGE OPTION ADDENDUM
www.ti.com
5-Jun-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
DRV8832DGQ
DRV8832DGQR
DRV8832DRCR
DRV8832DRCT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
MSOP-
PowerPAD
DGQ
DGQ
DRC
DRC
10
10
10
10
80
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSOP-
PowerPAD
2500
3000
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
CU NIPDAU Level-2-260C-1 YEAR
SON
Green (RoHS
& no Sb/Br)
SON
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Jun-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
DRV8832DGQR
MSOP-
Power
PAD
DGQ
10
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
DRV8832DRCR
DRV8832DRCT
SON
SON
DRC
DRC
10
10
3000
250
330.0
180.0
12.4
12.4
3.3
3.3
3.3
3.3
1.1
1.1
8.0
8.0
12.0
12.0
Q2
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Jun-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
DRV8832DGQR
DRV8832DRCR
DRV8832DRCT
MSOP-PowerPAD
DGQ
DRC
DRC
10
10
10
2500
3000
250
346.0
346.0
210.0
346.0
346.0
185.0
29.0
29.0
35.0
SON
SON
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明