DS25CP102TSQX [TI]
IC,ANALOG SWITCH,SINGLE,2X2 CROSSPOINT,LLCC,16PIN,PLASTIC;型号: | DS25CP102TSQX |
厂家: | TEXAS INSTRUMENTS |
描述: | IC,ANALOG SWITCH,SINGLE,2X2 CROSSPOINT,LLCC,16PIN,PLASTIC 输出元件 |
文件: | 总17页 (文件大小:433K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
National Semiconductor is now part of
Texas Instruments.
Search http://www.ti.com/ for the latest technical
information and details on our current products and services.
March 18, 2009
DS25CP102
3.125 Gbps 2X2 LVDS Crosspoint Switch with Transmit
Pre-Emphasis and Receive Equalization
General Description
Features
The DS25CP102 is a 3.125 Gbps 2x2 LVDS crosspoint switch
optimized for high-speed signal routing and switching over
lossy FR-4 printed circuit board backplanes and balanced ca-
bles. Fully differential signal paths ensure exceptional signal
integrity and noise immunity. The non-blocking architecture
allows connections of any input to any output or outputs.
DC - 3.125 Gbps low jitter, low skew, low power operation
■
■
Pin configurable, fully differential, non-blocking
architecture
Pin selectable transmit pre-emphasis and receive
equalization eliminate data dependant jitter
■
Wide Input Common Mode Voltage Range allows DC-
coupled interface to CML and LVPECL drivers
■
The DS25CP102 features two levels (Off and On) of transmit
pre-emphasis (PE) and two levels (Off and On) of receive
equalization (EQ).
On-chip 100Ω input and output termination minimizes
insertion and return losses, reduces component count and
minimizes board space
■
Wide input common mode range allows the switch to accept
signals with LVDS, CML and LVPECL levels; the output levels
are LVDS. A very small package footprint requires a minimal
space on the board while the flow-through pinout allows easy
board layout. Each differential input and output is internally
terminated with a 100Ω resistor to lower device insertion and
return losses, reduce component count and further minimize
board space.
8 kV ESD on LVDS I/O pins protects adjoining
components
Small 4 mm x 4 mm LLP-16 space saving package
■
■
Applications
High-speed channel select applications
■
■
■
■
Clock and data buffering and muxing
OC-48 / STM-16
SD/HD/3GHD SDI Routers
Typical Application
30008003
© 2009 National Semiconductor Corporation
300080
www.national.com
Ordering Code
NSID
Function
Available Equalization
Levels
Available Pre-Emphasis
Levels
DS25CP102TSQ
Crosspoint Switch
Off / On
Off / On
Block Diagram
Connection Diagram
30008001
30008002
Pin Descriptions
Pin Name
Pin Number I/O, Type
Pin Description
IN0+, IN0- ,
IN1+, IN1-
1, 2,
3, 4
I, LVDS
Inverting and non-inverting high speed LVDS input pins.
OUT0+, OUT0-,
OUT1+, OUT1-
12, 11,
10, 9
O, LVDS
Inverting and non-inverting high speed LVDS output pins.
SEL0, SEL1
EN0, EN1
PE
7, 8
14, 13
15
I, LVCMOS
I, LVCMOS
I, LVCMOS
I, LVCMOS
Power
Switch configuration pins. There is a 20k pulldown resistor on this pin.
Output enable pins. There is a 20k pulldown resistor on this pin.
Transmit Pre-Emphasis select pin. There is a 20k pulldown resistor on this pin.
Receive Equalizaton select pin. There is a 20k pulldown resistor on this pin.
Power supply pin.
EQ
6
VDD
16
GND
5, DAP
Power
Ground pin and Device Attach Pad (DAP) ground.
www.national.com
2
Package Thermal Resistance
Absolute Maximum Ratings (Note 4)
ꢀθJA
+41.8°C/W
+6.9°C/W
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
ꢀθJC
ESD Susceptibility
HBM (Note 1)
Supply Voltage
−0.3V to +4V
−0.3V to (VCC + 0.3V)
−0.3V to +4V
≥8 kV
≥250V
LVCMOS Input Voltage
LVDS Input Voltage
MM (Note 2)
CDM (Note 3)
≥1250V
LVDS Differential Input Voltage
LVDS Output Voltage
0V to 1.0V
−0.3V to (VCC + 0.3V)
0V to 1.0V
Note 1: Human Body Model, applicable std. JESD22-A114C
Note 2: Machine Model, applicable std. JESD22-A115-A
LVDS Differential Output Voltage
Note 3: Field Induced Charge Device Model, applicable std.
JESD22-C101-C
LVDS Output Short Circuit Current
Duration
5 ms
Junction Temperature
Storage Temperature Range
Lead Temperature Range
Soldering (4 sec.)
Maximum Package Power Dissipation at 25°C
SQA Package
+150°C
−65°C to +150°C
Recommended Operating
Conditions
Min
3.0
0
Typ
Max Units
+260°C
Supply Voltage (VCC
)
3.3
3.6
1
V
V
Receiver Differential Input
Voltage (VID)
2.99W
23.9 mW/°C above +25°C
Derate SQA Package
Operating Free Air
Temperature (TA)
−40
+25
+85
°C
DC Electrical Characteristics (Notes 5, 6, 7)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol Parameter Conditions
LVCMOS DC SPECIFICATIONS
Min
Typ
Max
Units
VIH
VIL
IIH
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
2.0
GND
40
VCC
0.8
V
V
VIN = 3.6V
VCC = 3.6V
175
0
250
μA
IIL
Low Level Input Current
VIN = GND
VCC = 3.6V
±10
μA
VCL
Input Clamp Voltage
ICL = −18 mA, VCC = 0V
−0.9
−1.5
V
LVDS INPUT DC SPECIFICATIONS
VID
Input Differential Voltage
0
1
V
mV
mV
V
VCM = +0.05V or VCC-0.05V
VID = 100 mV
VTH
VTL
Differential Input High Threshold
Differential Input Low Threshold
Common Mode Voltage Range
0
0
+100
−100
0.05
VCMR
VCC -
0.05
±10
VIN = +3.6V or 0V
VCC = 3.6V or 0V
±1
μA
IIN
Input Current
CIN
RIN
1.7
pF
Input Capacitance
Any LVDS Input Pin to GND
Between IN+ and IN-
100
Input Termination Resistor
Ω
3
www.national.com
Symbol
Parameter
Conditions
Min
Typ
Max
Units
LVDS OUTPUT DC SPECIFICATIONS
VOD
Differential Output Voltage
250
-35
350
450
35
mV
mV
V
RL = 100Ω
RL = 100Ω
Change in Magnitude of VOD for Complimentary
Output States
ΔVOD
VOS
Offset Voltage
1.05
-35
1.2
1.375
35
Change in Magnitude of VOS for Complimentary
Output States
ΔVOS
mV
IOS
Output Short Circuit Current (Note 8)
OUT to GND
-35
7
-55
55
mA
mA
pF
Ω
OUT to VCC
COUT
ROUT
Output Capacitance
Any LVDS Output Pin to GND
Between OUT+ and OUT-
1.2
100
Output Termination Resistor
SUPPLY CURRENT
ICC
Supply Current
Supply Current with Outputs Disabled
PE = OFF, EQ = OFF
EN0 = EN1 = 0
77
23
90
29
mA
mA
ICCZ
Note 4: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability
and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in
the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the
device should not be operated beyond such conditions.
Note 5: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified
or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed.
Note 6: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD and
ΔVOD
.
Note 7: Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions at the time of
product characterization and are not guaranteed.
Note 8: Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only.
www.national.com
4
AC Electrical Characteristics (Note 11)
Over recommended operating supply and temperature ranges unless otherwise specified. (Notes 9, 10)
Symbol
LVDS OUTPUT AC SPECIFICATIONS
tPLHD Differential Propagation Delay Low to
Parameter
Conditions
Min
Typ
Max
Units
365
345
500
500
ps
ps
High
RL = 100Ω
tPHLD
Differential Propagation Delay High to
Low
tSKD1
tSKD2
tSKD3
tLHT
Pulse Skew |tPLHD − tPHLD| (Note 12)
Channel to Channel Skew (Note 13)
Part to Part Skew , (Note 14)
Rise Time
20
12
50
65
65
7
55
25
ps
ps
ps
ps
ps
150
120
120
20
RL = 100Ω
tHLT
Fall Time
tON
Output Enable Time
Output Disable Time
Select Time
ENn = LH to output active
ENn = HL to output inactive
SELn LH or HL to output
μs
ns
ns
tOFF
tSEL
5
12
3.5
12
JITTER PERFORMANCE WITH EQ = Off, PE = Off (Figure 5)
tRJ1
tRJ2
VID = 350 mV
2.5 Gbps
0.5
0.5
6
1
1
ps
ps
Random Jitter (RMS Value)
No Test Channels
(Note 15)
VCM = 1.2V
3.125 Gbps
2.5 Gbps
Clock (RZ)
tDJ1
tDJ2
VID = 350 mV
VCM = 1.2V
22
ps
Deterministic Jitter (Peak to Peak)
No Test Channels
(Note 16)
3.125 Gbps
2.5 Gbps
6
22
ps
K28.5 (NRZ)
VID = 350 mV
VCM = 1.2V
tTJ1
tTJ2
UIP-P
UIP-P
0.03
0.05
0.08
0.11
Total Jitter (Peak to Peak)
No Test Channels
(Note 17)
3.125 Gbps
PRBS-23 (NRZ)
JITTER PERFORMANCE WITH EQ = Off, PE = On ((Notes 6, 9) )
tRJ1B
tRJ2B
VID = 350 mV
2.5 Gbps
0.5
0.5
3
1
1
ps
ps
Random Jitter (RMS Value)
Test Channel B
(Note 15)
VCM = 1.2V
3.125 Gbps
2.5 Gbps
Clock (RZ)
tDJ1B
tDJ2B
VID = 350 mV
VCM = 1.2V
12
ps
Deterministic Jitter (Peak to Peak)
Test Channel B
(Note 16)
3.125 Gbps
2.5 Gbps
3
12
ps
K28.5 (NRZ)
VID = 350 mV
VCM = 1.2V
tTJ1B
tTJ2B
UIP-P
UIP-P
0.03
0.04
0.06
0.09
Total Jitter (Peak to Peak)
Test Channel B
(Note 17)
3.125 Gbps
PRBS-23 (NRZ)
JITTER PERFORMANCE WITH EQ = On, PE = Off ((Notes 7, 8) )
tRJ1D
tRJ2D
VID = 350 mV
2.5 Gbps
0.5
0.5
1
1
ps
ps
Random Jitter (RMS Value)
Test Channel D
(Note 15)
VCM = 1.2V
3.125 Gbps
2.5 Gbps
Clock (RZ)
tDJ1D
tDJ2D
VID = 350 mV
VCM = 1.2V
16
24
ps
Deterministic Jitter (Peak to Peak)
Test Channel D
(Note 16)
3.125 Gbps
2.5 Gbps
12
24
ps
K28.5 (NRZ)
VID = 350 mV
VCM = 1.2V
tTJ1D
tTJ2D
UIP-P
UIP-P
0.07
0.07
0.11
0.11
Total Jitter (Peak to Peak)
Test Channel D
(Note 17)
3.125 Gbps
PRBS-23 (NRZ)
5
www.national.com
Symbol
Parameter
Conditions
Min
Typ
Max
Units
JITTER PERFORMANCE WITH EQ = On, PE = On ((Notes 9, 9) )
tRJ1BD
tRJ2BD
Random Jitter (RMS Value)
Input Test Channel D
Output Test Channel B
(Note 15)
VID = 350 mV
VCM = 1.2V
Clock (RZ)
2.5 Gbps
0.5
0.5
14
1
1
ps
ps
3.125 Gbps
2.5 Gbps
tDJ1BD
tDJ2BD
Deterministic Jitter (Peak to Peak)
Input Test Channel D
Output Test Channel B
(Note 16)
VID = 350 mV
VCM = 1.2V
31
ps
3.125 Gbps
2.5 Gbps
6
21
ps
K28.5 (NRZ)
tTJ1BD
tTJ2BD
Total Jitter (Peak to Peak)
Input Test Channel D
Output Test Channel B
(Note 17)
VID = 350 mV
VCM = 1.2V
UIP-P
UIP-P
0.08
0.10
0.15
0.16
3.125 Gbps
PRBS-23 (NRZ)
Note 9: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified
or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed.
Note 10: Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions at the time of
product characterization and are not guaranteed.
Note 11: Specification is guaranteed by characterization and is not tested in production.
Note 12: tSKD1, |tPLHD − tPHLD|, Pulse Skew, is the magnitude difference in differential propagation delay time between the positive going edge and the negative
going edge of the same channel.
Note 13: tSKD2, Channel to Channel Skew, is the difference in propagation delay (tPLHD or tPHLD) among all output channels in Broadcast mode (any one input to
all outputs).
Note 14: tSKD3, Part to Part Skew, is defined as the difference between the minimum and maximum differential propagation delays. This specification applies to
devices at the same VCC and within 5°C of each other within the operating temperature range.
Note 15: Measured on a clock edge with a histogram and an acummulation of 1500 histogram hits. Input stimulus jitter is subtracted geometrically.
Note 16: Tested with a combination of the 1100000101 (K28.5+ character) and 0011111010 (K28.5- character) patterns. Input stimulus jitter is subtracted
algebraically.
Note 17: Measured on an eye diagram with a histogram and an acummulation of 3500 histogram hits. Input stimulus jitter is subtracted.
www.national.com
6
DC Test Circuits
30008020
FIGURE 1. Differential Driver DC Test Circuit
AC Test Circuits and Timing Diagrams
30008021
FIGURE 2. Differential Driver AC Test Circuit
30008022
FIGURE 3. Propagation Delay Timing Diagram
30008023
FIGURE 4. LVDS Output Transition Times
7
www.national.com
Pre-Emphasis and Equalization Test Circuits
30008029
FIGURE 5. Jitter Performance Test Circuit
30008027
FIGURE 6. Pre-Emphasis Performance Test Circuit
30008026
FIGURE 7. Equalization Performance Test Circuit
www.national.com
8
30008030
FIGURE 8. Pre-Emphasis and Equalization Performance Test Circuit
30008028
FIGURE 9. Test Channel Block Diagram
stant of 3.7 and Loss Tangent of 0.02). The edge coupled
differential striplines have the following geometries: Trace
Width (W) = 5 mils, Gap (S) = 5 mils, Height (B) = 16 mils.
Test Channel Loss Characteristics
The test channel was fabricated with Polyclad PCL-FR-370-
Laminate/PCL-FRP-370 Prepreg materials (Dielectric con-
Test Channel
Length
Insertion Loss (dB)
(inches)
500 MHz
-1.2
750 MHz
-1.7
1000 MHz
-2.0
1250 MHz
-2.4
1500 MHz
-2.7
1560 MHz
-2.8
A
B
C
D
E
F
10
20
30
15
30
60
-2.6
-3.5
-4.1
-4.8
-5.5
-5.6
-4.3
-5.7
-7.0
-8.2
-9.4
-9.7
-1.6
-2.2
-2.7
-3.2
-3.7
-3.8
-3.4
-4.5
-5.6
-6.6
-7.7
-7.9
-7.8
-10.3
-12.4
-14.5
-16.6
-17.0
9
www.national.com
Functional Description
The DS25CP102 is a 3.125 Gbps 2x2 LVDS digital crosspoint
switch optimized for high-speed signal routing and switching
over lossy FR-4 printed circuit board backplanes and bal-
anced cables.
TABLE 1. Switch Configuration Truth Table
SEL0 OUT1
IN0
SEL1
OUT0
IN0
0
0
1
1
0
1
0
1
IN0
IN1
IN1
IN1
IN0
IN1
TABLE 2. Output Enable Truth Table
EN1
EN0
OUT1
OUT0
0
0
1
1
0
1
0
1
Disabled
Disabled
Enabled
Enabled
Disabled
Enabled
Disabled
Enabled
In addition, the DS25CP102 has a pre-emphasis control pin
for switching the transmit pre-emphasis to ON and OFF set-
ting and an equalization control pin for switching the receive
equalization to ON and OFF setting. The following are the
transmit pre-emphasis and receive equalization truth tables.
Transmit Pre-Emphasis Truth Table
OUTPUTS OUT0 and OUT1
CONTROL Pin (PE) State
Pre-Emphasis Level
0
1
OFF
ON
Transmit Pre-Emphasis Level Selection
Receive Equalization Truth Table
INPUTS IN0 and IN1
CONTROL Pin (EQ) State
Equalization Level
0
1
OFF
ON
Receive Equalization Level Selection
www.national.com
10
drivers (i.e. LVPECL, LVDS, CML). The following three fig-
ures illustrate typical DC-coupled interface to common differ-
ential drivers. Note that the DS25CP102 inputs are internally
terminated with a 100Ω resistor.
Input Interfacing
The DS25CP102 accepts differential signals and allows sim-
ple AC or DC coupling. With a wide common mode range, the
DS25CP102 can be DC-coupled with all common differential
Typical LVDS Driver DC-Coupled Interface to DS25CP102 Input30008031
30008032
Typical CML Driver DC-Coupled Interface to DS25CP102 Input
30008033
Typical LVPECL Driver DC-Coupled Interface to DS25CP102 Input
11
www.national.com
and assumes that the receivers have high impedance inputs.
While most differential receivers have a common mode input
range that can accommodate LVDS compliant signals, it is
recommended to check respective receiver's data sheet prior
to implementing the suggested interface implementation.
Output Interfacing
The DS25CP102 outputs signals that are compliant to the
LVDS standard. Its outputs can be DC-coupled to most com-
mon differential receivers. The following figure illustrates typ-
ical DC-coupled interface to common differential receivers
30008034
Typical DS25CP102 Output DC-Coupled Interface to an LVDS, CML or LVPECL Receiver
www.national.com
12
Typical Performance Characteristics
Total Jitter as a Function of Data Rate30008050
Residual Jitter as a Function of Data Rate, FR43S00t08r0i5p2line
Length and EQ Level
30008058
Total Jitter as a Function of Input Common Mode Voltage
Supply Current as a Function of Data Rate and3P00E080L57evel
Residual Jitter as a Function of Data Rate, FR43S00t08r0i5p1line
Length and PE Level
13
www.national.com
30008060
30008062
A 3.125 Gbps NRZ PRBS-7 without PE or EQ
A 3.125 Gbps NRZ PRBS-7 with PE
After 40" Differential FR-4 Stripline
H: 50 ps / DIV, V: 100 mV / DIV
After 2" Differential FR-4 Stripline
H: 50 ps / DIV, V: 100 mV / DIV
A 3.125 Gbps NRZ PRBS-7 without PE or3E000Q8061
After 40" Differential FR-4 Stripline
H: 50 ps / DIV, V: 100 mV / DIV
www.national.com
14
Physical Dimensions inches (millimeters) unless otherwise noted
Order Number DS25CP102TSQ
NS Package Number SQA16A
(See AN-1187 for PCB Design and Assembly Recommendations)
15
www.national.com
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
Products
www.national.com/amplifiers
Design Support
Amplifiers
WEBENCH® Tools
App Notes
www.national.com/webench
www.national.com/appnotes
www.national.com/refdesigns
www.national.com/samples
www.national.com/evalboards
www.national.com/packaging
www.national.com/quality/green
www.national.com/contacts
Audio
www.national.com/audio
www.national.com/timing
www.national.com/adc
www.national.com/interface
www.national.com/lvds
www.national.com/power
www.national.com/switchers
www.national.com/ldo
Clock and Timing
Data Converters
Interface
Reference Designs
Samples
Eval Boards
LVDS
Packaging
Power Management
Switching Regulators
LDOs
Green Compliance
Distributors
Quality and Reliability www.national.com/quality
LED Lighting
Voltage Reference
PowerWise® Solutions
www.national.com/led
Feedback/Support
Design Made Easy
Solutions
www.national.com/feedback
www.national.com/easy
www.national.com/vref
www.national.com/powerwise
www.national.com/solutions
www.national.com/milaero
www.national.com/solarmagic
www.national.com/AU
Serial Digital Interface (SDI) www.national.com/sdi
Mil/Aero
Temperature Sensors
Wireless (PLL/VCO)
www.national.com/tempsensors SolarMagic™
www.national.com/wireless
Analog University®
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2009 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
Email: support@nsc.com
Tel: 1-800-272-9959
www.national.com
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明