首页 |元器件品牌

DS26LS31MW-QMLV [TI]

QUAD LINE DRIVER, CDFP16, CERAMIC, DFP-16;
DS26LS31MW-QMLV
型号： DS26LS31MW-QMLV
厂家： TEXAS INSTRUMENTS    TEXAS INSTRUMENTS
描述：

QUAD LINE DRIVER, CDFP16, CERAMIC, DFP-16

驱动 CD 接口集成电路 驱动器
文件： 总14页 (文件大小：641K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
DS26LS31MQML  
DS26LS31MQML Quad High Speed Differential Line Driver  
Literature Number: SNOSAM5A  
March 2006  
DS26LS31MQML  
Quad High Speed Differential Line Driver  
General Description  
Features  
n Operation from single 5V supply  
n Outputs won’t load line when VCC = 0V  
The DS26LS31MQML is a quad differential line driver de-  
signed for digital data transmission over balanced lines. The  
DS26LS31MQML meets all the requirements of EIA Stan-  
dard RS-422 and Federal Standard 1020. It is designed to  
provide unipolar differential drive to twisted-pair or parallel-  
wire transmission lines.  
n Four line drivers in one package for maximum package  
density  
n Output short-circuit protection  
n Complementary outputs  
The circuit provides an enable and disable function common  
to all four drivers. The DS26LS31MQML features TRI-  
STATE outputs and logically ANDed complementary out-  
puts. The inputs are all LS compatible and are all one unit  
load.  
n Meets the requirements of EIA Standard RS-422  
n Pin compatible with AM26LS31  
n Glitch free power up/down  
®
The DS26LS31 features a power up/down protection circuit  
which keeps the output in a high impedance stat (TRI-  
STATE) during power up or down preventing erroneous  
glitches on the transmission lines.  
Ordering Information  
NS PART NUMBER  
SMD PART NUMBER  
5962F7802301Q2A  
300k rd(Si)  
NS PACKAGE NUMBER  
PACKAGE DISCRIPTION  
DS26LS31MEFQML  
20LD Ceramic Leadless Chip Carrier  
E20A  
E20A  
J16A  
J16A  
J16A  
J16A  
W16A  
W16A  
W16A  
DS26LS31ME-SMD  
DS26LS31MJFQML  
5962-7802301Q2A  
5962F7802301MEA  
300k rd(Si)  
20LD Ceramic Leadless Chip Carrier  
16LD Ceramic Dual-In-Line  
DS26LS31MJ-SMD  
5962-7802301MEA  
5962F7802301VEA  
300k rd(Si)  
16LD Ceramic Dual-In-Line  
16LD Ceramic Dual-In-Line  
DS26LS31MJFQMLV  
DS26LS31MJ-QMLV  
DS26LS31MWFQML  
5962-7802301VEA  
5962F7802301MFA  
300k rd(Si)  
16LD Ceramic Dual-In-Line  
16LD Ceramic Flatpak  
DS26LS31MW-SMD  
DS26LS31MWFQMLV  
5962-7802301MFA  
5962F7802301VFA  
300k rd(Si)  
16LD Ceramic Flatpak  
16LD Ceramic Flatpak  
DS26LS31MW-QMLV  
DS26LS31MJ/883  
DS26LS31MW/883  
5962-7802301VFA  
W16A  
J16A  
16LD Ceramic Flatpak  
16LD Ceramic Dual-in-line  
16LD Ceramic Flatpak  
W16A  
TRI-STATE® is a registered trademark of National Semiconductor Corporation.  
© 2006 National Semiconductor Corporation  
DS201412  
www.national.com  
Logic and Connection Diagrams  
20141201  
Dual-In-Line Package  
20141202  
Top View  
See NS Package E20A, J16A or W16A  
www.national.com  
2
Absolute Maximum Ratings (Note 1)  
Supply Voltage  
7V  
7V  
Input Voltage  
Output Voltage  
5.5V  
Output Voltage (Power OFF)  
Maximum Power Dissipation at 25˚C  
(Note 2)  
−0.25 to 6V  
J Package  
1400 mW  
1600 mW  
850 mW  
+150˚C  
LCC Package  
W Package  
Junction Temperature (TJ)  
Thermal Resistance, Junction-to-Ambient  
θJA  
J Package  
94˚C/W derate above +25˚C at 10.6 mW/˚C  
83˚C/W derate above +25˚C at 12 mW/˚C  
163˚C/W derate above +25˚C at 6.1 mW/˚C  
LCC Package  
W Package  
Thermal Resistance, Junction-to-Case  
θJC  
J Package  
16˚C/W  
19˚C/W  
14˚C/W  
2500V  
LCC Package  
W Package  
ESD Tolerance  
Recommended Operating  
Conditions  
Supply Voltage, VCC  
Temperature, TA  
4.5 V to 5.5 V  
−55˚C to +125˚C  
Radiation Features  
DS26LS31MEFQML  
DS26LS31MJFQML  
DS26LS31MJFQMLV  
DS26LS31MWFQML  
DS26LS31MWFQMLV  
300 Krads (Si)  
300 Krads (Si)  
300 Krads (Si)  
300 Krads (Si)  
300 Krads (Si)  
3
www.national.com  
Quality Conformance Inspection  
MIL-STD-883, Method 5005 - Group A  
Subgroup  
Description  
Static tests at  
Temp (˚C)  
+25  
1
2
Static tests at  
+125  
-55  
3
Static tests at  
4
Dynamic tests at  
Dynamic tests at  
Dynamic tests at  
Functional tests at  
Functional tests at  
Functional tests at  
Switching tests at  
Switching tests at  
Switching tests at  
+25  
5
+125  
-55  
6
7
+25  
8A  
8B  
9
+125  
-55  
+25  
10  
11  
+125  
-55  
DS26LS31M - SMD, QMLV & RH Electrical Characteristics  
DC Parameters  
The following conditions apply, unless otherwise specified. +V = 5V, VCM = 0V. (Note 5)  
Sub-  
Symbol  
Parameters  
Conditions  
Notes  
(Notes 3,  
4)  
Min Max  
Units  
groups  
VIH  
Logical "1" Input Voltage  
VCC = 4.5V  
2
V
1, 2, 3  
1, 2, 3  
(Notes 3,  
4)  
VIL  
Logical "0" Input Voltage  
VCC = 5.5V  
.8  
V
VOH  
VOL  
IIH  
Logical "1" Output Voltage  
Logical "0" Output Voltage  
Logical "1" Input Current  
Logical "0" Input Current  
Input Reverse Current  
VCC = 4.5V, IOH = -20mA  
VCC = 4.5V, IOL = 20mA  
VCC = 5.5V, VIN= 2.7V  
VCC = 5.5V, VIN = .4V  
VCC = 5.5V, VIN = 7V  
VCC = 5.5V, VO = .5V  
VCC = 5.5V, VO = 2.5V  
VCC = 4.5V, IIN = -18mA  
VCC = 5.5V  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
2.5  
.5  
V
V
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
-2.0  
20  
uA  
uA  
mA  
uA  
uA  
V
IIL  
100 -360  
II  
-.01  
-30  
.1  
-20  
20  
IO  
TRI-STATE Output Current  
VIC  
IOS  
Input Clamp Voltage  
-1.5  
-150  
Output Short Circuit Current  
mA  
VCC = 5.5V, All Outputs  
Disabled or Active  
ICC  
Power Supply Current  
(Note 4)  
80  
mA  
1, 2, 3  
AC Parameters - Propagation Delay Time  
The following conditions apply, unless otherwise specified. VCC = 5V, VIN = 1.3V to VO = 1.3V, V (pulse) = 0 to 3V. (Note 5)  
Sub-  
Symbol  
Parameters  
Conditions  
Notes  
Min Max  
Unit  
nS  
nS  
nS  
nS  
nS  
nS  
groups  
9
20  
30  
20  
30  
6
tPLH  
Input to Output  
CL = 30 pF  
(Note 4)  
10, 11  
9
tPHL  
Input to Output  
CL = 30 pF  
CL = 30 pF  
(Note 4)  
(Note 4)  
10, 11  
9
tSkew  
Output to Output  
9
10, 11  
www.national.com  
4
DS26LS31M - SMD, QMLV & RH Electrical Characteristics (Continued)  
AC Parameters - Propagation Delay Time (Continued)  
The following conditions apply, unless otherwise specified. VCC = 5V, VIN = 1.3V to VO = 1.3V, V (pulse) = 0 to 3V. (Note 5)  
Sub-  
Symbol  
Parameters  
Conditions  
Notes  
Min Max  
Unit  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
groups  
35  
53  
35  
53  
30  
45  
30  
45  
45  
68  
45  
68  
40  
60  
40  
60  
9
10, 11  
9
S2 Open, Enable, CL = 10 pF  
(Note 4)  
tPLZ  
Enable to Output  
S2 Open, Enable, CL = 10 pF  
S1 Open, Enable, CL = 10 pF  
S1 Open, Enable, CL = 10 pF  
S2 Open, Enable, CL = 30 pF  
S2 Open, Enable, CL = 30 pF  
S1 Open, Enable, CL = 30 pF  
S1 Open, Enable, CL = 30 pF  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
10, 11  
9
10, 11  
9
tPHZ  
tPZL  
tPZH  
Enable to Output  
Enable to Output  
Enable to Output  
10, 11  
9
10, 11  
9
10, 11  
9
10, 11  
9
10, 11  
DC Parameters - Drift Values  
The following conditions apply, unless otherwise specified. Delta calculations performed on QMLV only devices after burn-in  
and at Group B5.  
Sub-  
Symbol  
VOL  
Parameters  
Conditions  
Notes  
(Note 4)  
(Note 4)  
Min Max  
-50 50  
-250 250  
Units  
mV  
groups  
Output Low Voltage  
Output High Voltage  
VCC = 4.5, IOL = 20 mA  
VCC = 4.5, IOH = -20 mA  
VCC = 5.5, All outputs disabled  
or active  
1
1
VOH  
mV  
ICC  
Power Supply Current  
(Note 4)  
-8  
8
mA  
1
5
www.national.com  
DS26LS31M - 883 Electrical Characteristics  
DC Parameters  
Sub-  
groups  
Symbol  
Parameters  
Conditions  
Notes  
Min Max  
Unit  
V
(Notes 3,  
4)  
VIH  
Logical "1" Input Voltage  
Logical "0" Input Voltage  
2
1, 2, 3  
1, 2, 3  
(Notes 3,  
4)  
VIL  
.8  
V
VOH  
VOL  
IIH  
Logical "1" Output Voltage  
Logical "0" Output Voltage  
Logical "1" Input Current  
Logical "0" Input Current  
Input Reverse Current  
VCC = 4.5V, IOH = -20mA  
VCC = 4.5V, IOL = 20mA  
VCC = 5.5V, VIN = 2.7V  
VCC = 5.5V, VIN = .4V  
VCC = 5.5V, VIN = 7V  
VCC = 5.5V, VO = .5V  
VCC = 5.5V, VO = 2.5V  
VCC = 4.5V, IIN = -18mA  
VCC = 5.5V  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
(Note 4)  
2.5  
.5  
V
V
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
1, 2, 3  
20  
uA  
uA  
mA  
uA  
uA  
V
IIL  
-200  
.1  
II  
-20  
20  
IO  
TRI-STATE Output Current  
VIC  
Input Clamp Voltage  
-1.5  
-30  
-150  
IOS (min)  
IOS (max)  
Output Short Circuit Current  
Output Short Circuit Current  
mA  
mA  
VCC = 5.5V  
VCC = 5.5V, All Outputs  
Disabled or Active  
ICC  
Power Supply Current  
(Note 4)  
60  
mA  
1, 2, 3  
AC Parameters - Propagation Delay Time  
The following conditions apply, unless otherwise specified. VCC = 5V, CL = 50pF or equivalent impedance provided by diode  
load.  
Sub-  
groups  
Symbol  
tPLH  
Parameters  
Conditions  
Notes  
Min Max  
Unit  
15  
30  
15  
30  
6
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
nS  
9
(Notes 4,  
6)  
Input to Output  
Input to Output  
Output to Output  
10, 11.  
9
(Notes 4,  
6)  
tPHL  
10, 11.  
9
(Notes 4,  
6)  
tSkew  
9
10, 11.  
35  
53  
35  
53  
25  
45  
25  
45  
30  
68  
30  
68  
30  
60  
30  
60  
9
10, 11.  
9
(Notes 4,  
6)  
S2 Open, Enable  
S2 Open, /Enable  
S1 Open, Enable  
S1 Open, /Enable  
S2 Open, Enable  
S2 Open, /Enable  
S1 Open, Enable  
S1 Open, /Enable  
tPLZ  
tPHZ  
tPZL  
tPZH  
Enable to Output  
Enable to Output  
Enable to Output  
Enable to Output  
(Notes 4,  
6)  
10, 11.  
9
(Notes 4,  
6)  
10, 11.  
9
(Notes 4,  
6)  
10, 11.  
9
(Notes 4,  
6)  
10, 11.  
9
(Notes 4,  
6)  
10, 11.  
9
(Notes 4,  
6)  
10, 11.  
9
(Notes 4,  
6)  
10, 11.  
www.national.com  
6
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices  
should be operated at these limits. The tables of “Electrical Characteristics” provide conditions for actual device operation.  
Note 2: Derate CDip = 11.5 mW/˚C, CLCC = 13mW/˚C, Cerpack = 7.4mW/˚C above 25˚C.  
Note 3: Parameter tested go-no-go only.  
Note 4: Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures.  
Note 5: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate sensitive in a space  
environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified  
in MIL-STD 883, Method 1019, Condition A.  
Note 6: Subgroup 10 and 11 guaranteed but not tested.  
AC Test Circuit and Switching Time Waveforms  
20141203  
S1 and S2 of load circuit are closed except where shown.  
FIGURE 1. AC Test Circuit  
20141204  
f = 1 MHz, t ≤ 15 ns, t ≤ 6 ns  
r
f
FIGURE 2. Propagation Delays  
20141205  
f = 1 MHz, t ≤ 15 ns, t ≤ 6 ns  
r
f
FIGURE 3. Enable and Disable Times  
7
www.national.com  
Typical Applications  
Two-Wire Balanced System, RS-422  
20141206  
Note 7: R is optional although highly recommended to reduce reflection.  
T
Typical Performance Characteristics  
DS26LS31MQMLCN Unloaded IC vs Frequency vs TA  
DS26LS31MQML ICC vs VCC vs TA  
20141207  
20141208  
DS26LS31MQMLCN VOH vs IOH vs TA  
DS26LS31MQMLCN VOL vs IOL vs TA  
20141210  
20141209  
www.national.com  
8
Typical Performance Characteristics (Continued)  
DS26LS31MQMLCN VOD vs IO vs TA  
20141211  
9
www.national.com  
Revision History Section  
Date  
Revision  
Released  
Section  
Originator  
Changes  
08/04/05  
A
New Release, Corporate format  
R. Malone  
2 MDS data sheets converted into a Corp.  
data sheet format. Following MDS data  
sheets will be Archived  
MDDS26LS31M-X-RH, Rev.2A0,  
MNDS26LS31M-X, Rev. 0A0  
03/01/06  
B
Ordering Info. Table, Absolute  
Ratings, Maximum Operating  
Conditions, New Radiation Section.  
Typo’s in QMLV & RH, 883 AC  
Electrical Characteristics Parameters  
Column  
R. Malone  
Added: Juction temp., Thermal Resistance  
θJA and θJC. Added a Radiation Section.  
Changed: Maximum Operating Conditions to  
Recommended Operating Conditions,  
Enable and Disable Time to Enable to  
Output. Revision A will be archived.  
www.national.com  
10  
Physical Dimensions inches (millimeters) unless otherwise noted  
16 Lead Ceramic Flatpak (W)  
NS Package Number W16A  
16 Lead Ceramic Dual-in-Line Package (J)  
NS Package Number J16A  
11  
www.national.com  
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)  
20 Lead Ceramic Leadless Chip Carrier (E)  
NS Package Number E20A  
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves  
the right at any time without notice to change said circuitry and specifications.  
For the most current product information visit us at www.national.com.  
LIFE SUPPORT POLICY  
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS  
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR  
CORPORATION. As used herein:  
1. Life support devices or systems are devices or systems  
which, (a) are intended for surgical implant into the body, or  
(b) support or sustain life, and whose failure to perform when  
properly used in accordance with instructions for use  
provided in the labeling, can be reasonably expected to result  
in a significant injury to the user.  
2. A critical component is any component of a life support  
device or system whose failure to perform can be reasonably  
expected to cause the failure of the life support device or  
system, or to affect its safety or effectiveness.  
BANNED SUBSTANCE COMPLIANCE  
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products  
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain  
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.  
Leadfree products are RoHS compliant.  
National Semiconductor  
Americas Customer  
Support Center  
National Semiconductor  
Europe Customer Support Center  
Fax: +49 (0) 180-530 85 86  
National Semiconductor  
Asia Pacific Customer  
Support Center  
National Semiconductor  
Japan Customer Support Center  
Fax: 81-3-5639-7507  
Email: new.feedback@nsc.com  
Tel: 1-800-272-9959  
Email: europe.support@nsc.com  
Deutsch Tel: +49 (0) 69 9508 6208  
English Tel: +44 (0) 870 24 0 2171  
Français Tel: +33 (0) 1 41 91 8790  
Email: ap.support@nsc.com  
Email: jpn.feedback@nsc.com  
Tel: 81-3-5639-7560  
www.national.com  
IMPORTANT NOTICE  
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,  
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should  
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are  
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.  
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard  
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where  
mandated by government requirements, testing of all parameters of each product is not necessarily performed.  
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and  
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide  
adequate design and operating safeguards.  
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,  
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information  
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a  
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual  
property of the third party, or a license from TI under the patents or other intellectual property of TI.  
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied  
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive  
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional  
restrictions.  
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all  
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not  
responsible or liable for any such statements.  
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably  
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing  
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and  
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products  
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be  
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in  
such safety-critical applications.  
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are  
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military  
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at  
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.  
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are  
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated  
products in automotive applications, TI will not be responsible for any failure to meet such requirements.  
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:  
Products  
Audio  
Applications  
www.ti.com/audio  
amplifier.ti.com  
dataconverter.ti.com  
www.dlp.com  
Communications and Telecom www.ti.com/communications  
Amplifiers  
Data Converters  
DLP® Products  
DSP  
Computers and Peripherals  
Consumer Electronics  
Energy and Lighting  
Industrial  
www.ti.com/computers  
www.ti.com/consumer-apps  
www.ti.com/energy  
dsp.ti.com  
www.ti.com/industrial  
www.ti.com/medical  
www.ti.com/security  
Clocks and Timers  
Interface  
www.ti.com/clocks  
interface.ti.com  
logic.ti.com  
Medical  
Security  
Logic  
Space, Avionics and Defense www.ti.com/space-avionics-defense  
Transportation and Automotive www.ti.com/automotive  
Power Mgmt  
Microcontrollers  
RFID  
power.ti.com  
microcontroller.ti.com  
www.ti-rfid.com  
Video and Imaging  
www.ti.com/video  
OMAP Mobile Processors www.ti.com/omap  
Wireless Connectivity www.ti.com/wirelessconnectivity  
TI E2E Community Home Page  
e2e.ti.com  
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265  
Copyright © 2011, Texas Instruments Incorporated  

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明