DS32EL0124SQX/NOPB [TI]
具有 DDR LVDS 并行接口的 125MHz 至 312.5MHz FPGA-Link 解串器 | RHS | 48 | -40 to 85;型号: | DS32EL0124SQX/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有 DDR LVDS 并行接口的 125MHz 至 312.5MHz FPGA-Link 解串器 | RHS | 48 | -40 to 85 双倍数据速率 接口集成电路 |
文件: | 总34页 (文件大小:2178K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
DS32EL0124 , DS32ELX0124 125 MHz - 312.5 MHz FPGA-Link Deserializer with DDR LVDS
Parallel Interface
Check for Samples: DS32EL0124, DS32ELX0124
1
FEATURES
KEY SPECIFICATIONS
2
•
5-bit DDR LVDS Parallel Data Interface
Programmable Receive Equalization
Selectable DC-Balance Decoder
Selectable De-Scrambler
•
•
•
•
•
1.25 to 3.125 Gbps Serial Data Rate
125 to 312.5 MHz DDR Parallel Clock
-40° to +85°C Temperature Range
> 8 kV ESD (HBM) Protection
•
•
•
•
Remote Sense for Automatic Detection and
Negotiation of Link Status
0.5 UI Minimum Input Jitter Tolerance (1.25
Gbps)
•
No External Receiver Reference Clock
Required
DESCRIPTION
The DS32EL0124/DS32ELX0124 integrates clock
and data recovery modules for high-speed serial
communication over FR-4 printed circuit board
backplanes, balanced cables, and optical fiber. This
easy-to-use chipset integrates advanced signal and
clock conditioning functions, with an FPGA friendly
interface.
•
•
•
•
•
•
•
•
•
•
•
LVDS Parallel Interface
Programmable LVDS Output Clock Delay
Supports Output Data-Valid Signaling
Supports Keep-Alive Clock Output
On Chip LC VCOs
Redundant Serial Input (ELX device only)
Retimed Serial Output (ELX device only)
Configurable PLL Loop Bandwidth
Configurable via SMBus
The DS32EL0124/DS32ELX0124 deserializes up to
3.125 Gbps of high speed serial data to 5 LVDS
outputs without the need for an external reference
clock. With DC-balance decoding enabled, the
application payload of 2.5 Gbps is deserialized to 4
LVDS outputs.
Loss of Lock and Error Reporting
48-pin WQFN Package with Exposed DAP
The
DS32EL0124/DS32ELX01214
deserializers
feature a remote sense capability to automatically
signal link status conditions to its companion
DS32EL0421/ELX0421 serializers without requiring
an additional feedback path.
APPLICATIONS
•
•
•
•
•
•
Imaging: Industrial, Medical Security, Printers
Displays: LED Walls, Commercial
Video Transport
The parallel LVDS interface of these devices reduce
FPGA I/O pins, board trace count and alleviates EMI
issues, when compared to traditional single-ended
wide bus interfaces.
Communication Systems
Test and Measurement
Industrial Bus
The DS32EL0124/ELX0124 is programmable through
a SMBus interface as well as through control pins.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
Typical Application
FPGA
FPGA
DS32ELX0421
DS32ELX0124
5 LVDS
5 LVDS
3.125 Gbps Data Payload
D0
D1
R0
R1
Redundant
Driver
Redundant Link
Retimed
Output
RT0
PLL
LVDS
Clock
LVDS
Clock
PLL
Control
Control
Control
Control
SMBus
SMBus
Connection Diagrams
VDD33
1
2
36
VDD33
VDD25
SMB_CS
SCK
N/C
GPIO0
GPIO1
DC_B
RS
35
34
33
32
31
30
29
28
27
26
25
49 DAP = GND
3
4
5
SDA
6
LOCK
DS32EL0124
VDD25
N/C
7
RESET
N/C
8
N/C
9
VDDPLL
LF_CP
LF_REF
VDD25
N/C
10
11
12
GPIO2
N/C
Figure 1. WQFN Package
Package Number RHS0048A
2
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
VDD33
LT_EN
GPIO0
GPIO1
DC_B
1
2
36
35
34
33
32
31
30
29
28
27
26
25
VDD33
VDD25
SMB_CS
SCK
49 DAP = GND
3
4
5
SDA
RS
6
LOCK
DS32ELX0124
VDD25
N/C
7
RESET
N/C
8
N/C
9
VDDPLL
LF_CP
LF_REF
VDD25
N/C
10
11
12
GPIO2
RX_MUX_SEL
Figure 2. WQFN Package
Package Number RHS0048A
PIN DESCRIPTIONS
Pin Name
VDD33
Pin Number
I/O, Type
Description
1, 15, 18, 36
I, VDD
I, VDD
I, VDD
Analog
Analog
GND
3.3V supply
VDD25
7, 25, 35
2.5V supply
VDD_PLL
LF_CP
28
27
26
49
3.3V supply
Loop filter capacitor connection
Loop filter ground reference
LF_REF
Exposed Pad
CML I/O
Exposed Pad must be connected to GND by 9 vias.
RxIN0+
RxIN0-
16
17
I, CML
I, CML
O, CML
Non-inverting and inverting high speed CML differential inputs of the
deserializer. These inputs are internally terminated.
RxIN1+
RxIN1-
19
20
DS32ELX0124 only. Non-inverting and inverting high speed CML
differential inputs of the deserializer. These inputs are internally terminated.
TxOUT+
TxOUT-
21
22
DS32ELX0124 only. Retimed serialized high speed output. Non-inverting
and inverting speed CML differential outputs of the deserializer. These
outputs are internally terminated.
LVDS Parallel Data Bus
RxCLKOUT+
RxCLKOUT-
37
38
O, LVDS
O, LVDS
Deserializer output clock. RxCLKOUT+/- are the non-inverting and inverting
LVDS recovered clock output pins.
RxOUT[0:4]+/-
39, 40, 41, 42, 43, 44, 45,
46, 47, 48
Deserializer output data. RxOUT[0:4]+/- are the non-inverting and inverting
LVDS deserialized output data pins.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
PIN DESCRIPTIONS (continued)
Pin Name
Control Pins
LT_EN
Pin Number
I/O, Type
Description
2
I, LVCMOS
I, LVCMOS
DS32ELX0124 only. When held high, retimed serialized high speed output
is enabled.
RX_MUX_SEL
VOD_CTRL
12
DS32ELX0124 only. RX_MUX_SEL selects the input of the deserializer.
0 = RxIN0+/- selected
1 = RxIN1+/- selected
14
I, LVCMOS
DS32ELX0124 only. VOD control. The deserializer loop through output
amplitude can be adjusted by connecting this pin to a pull-down resistor.
The value of the pull-down resistor determines the VOD. See LOOP
THROUGH DRIVER LAUNCH AMPLITUDE for more details.
DC_B
RS
5
6
I, LVCMOS
I, LVCMOS
DC-balance and Remote Sense pins. See Applications Information for
device behavior.
RESET
30
Reset pin. When held low, reset the device.
0 = Device Reset
1 = Normal operation
LOCK
31
O, LVCMOS Lock indication output. pin goes low when the deserializer is locked to the
incoming data stream and begins to output data and clock on RxOUT and
RxCLKOUT respectively.
0 = Deserializer locked
1 = Deserializer not locked
SMBus
SCK
I, SMBus
I/O, SMBus
I, SMBus
33
32
34
SMBus compatible clock.
SDA
SMBus compatible data line.
SMB_CS
SMBus chip select. When held high, SMBus management control is
enabled.
Other
GPIO0
GPIO1
GPIO2
NC
3
I/O, LVCMOS Software configurable IO pins.
I/O, LVCMOS Software configurable IO pins.
I/O, LVCMOS Software configurable IO pins.
4
11
2 ,8, 9, 10, 12, 13, 14, 19,
20, 21, 22, 23, 24, 29
Misc.
No Connect, for DS32EL0124
8, 9, 10, 13, 23, 24, 29
Misc
No Connect, for DS32ELX0124
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
4
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
Absolute Maximum Ratings(1)(2)
Supply Voltage (VDD33
)
−0.3V to +4V
-0.3V to +3.0V
Supply Voltage (VDD25
)
LVCMOS Input Voltage
LVCMOS Output Voltage
CML Input/Output Voltage
LVDS Output Voltage
Junction Temperature
Storage Temperature Range
Lead Temperature Range
Soldering (4 sec.)
−0.3V to (VDD33 + 0.3V)
-0.3V to (VDD33 + 0.3V)
-0.3V to 3.6V
-0.3V to +3.6V
+125°C
−65°C to +150°C
+260°C
+25.0°C/W
≥8 kV
Package Thermal Resistance
θJA
ESD Susceptibility
HBM
(1) “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating
Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Recommended Operating Conditions
Min
Typ
3.3
2.5
Max
3.465
2.625
100
Units
V
Supply Voltage (VDD33
Supply Voltage (VDD25
)
)
3.135
2.375
V
Supply Noise Amplitude from 10 Hz to 50 MHz
Ambient Temperature (TA)
mVP-P
°C
−40
+25
+85
SMBus Pull–Up Resistor to VSDD Value
1000
Ω
Table 1. Power Supply Characteristics
Symbol
Parameter
Condition
1.25 Gbps
2.5 Gbps
Min
Typ
50
Max
Unit
IDD25
2.5V supply current
59
Loop Through Driver Disabled
62
73
3.125 Gbps
1.25 Gbps
2.5 Gbps
69
79
mA
2.5V supply current
Loop Through Driver Enabled
88
99
100
107
105
105
105
111
111
111
475
500
520
590
620
640
112
120
121
121
121
127
127
127
560
600
620
690
730
750
3.125 Gbps
1.25 Gbps
2.5 Gbps
IDD33
3.3V supply current
Loop Through Driver Disabled
3.125 Gbps
1.25 Gbps
2.5 Gbps
mA
3.3V supply current
Loop Through Driver Enabled
3.125 Gbps
1.25 Gbps
2.5 Gbps
PD
Power Consumption
Loop Through Driver Disabled
3.125 Gbps
1.25 Gbps
2.5 Gbps
mW
Power Consumption
Loop Through Driver Enabled
3.125 Gbps
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
LVCMOS Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified. Applies to LT_EN, GPIO0, GPIO1,
(1) (2) (3)
GPIO2, RX_MUX_SEL, DC_B, RESET, RS, LOCK.
Symbol
VIH
Parameter
High Level Input Voltage
Conditions
Min
2.0
Typ
Max
VDD
0.8
Units
V
VIL
Low Level Input Voltage
High Level Output Voltage
Low Level Output Voltage
Input Clamp Voltage
GND
2.7
V
VOH
VOL
VCL
IIN
IOH = -2mA
IOL = 2mA
3.2
-0.9
-45
V
0.3V
−1.5
40
V
ICL = −18 mA
V
Input Current
VIN = 0.4V, 2.5V, or VDD33
-40
μA
mA
IOS
Output Short Circuit Current
VOUT = 0V
(4)
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground
except VOD and ΔVOD
.
(3) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(4) Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only.
SMBus Electrical Specifications
Over recommended operating supply and temperature ranges unless otherwise specified.
(1) (2)
Symbol
VSIL
Parameter
Data, Clock Input Low Voltage
Data, Clock Input High Voltage
Nominal Bus Voltage
Conditions
Min
Typ
Max
0.8
Units
V
VSIH
2.1
VSDD
3.465
V
VSDD
2.375
V
ISLEAKB
ISLEAKP
CSI
Input Leakage Per Bus Segment
Input Leakage Per Pin
SCK and SDA pins
±200
±10
10
µA
µA
pF
Capacitance for SDA and SCK
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
SMBus Timing Specifications
Over recommended operating supply and temperature ranges unless otherwise specified.
(1) (2)
Symbol
fSMB
Parameter
Bus Operating Frequency
Conditions
Min
10
Typ
Max
Units
kHz
μs
100
tBUF
Bus free time between top and start condition
4.7
4.0
tHD:STA
Hold time after (repeated) start condition. After this
period, the first clock is generated
µs
(3)
(3)
tSU:STA
tHD:DAT
tSU:DAT
tLOW
Repeated Start Condition Setup Time
Data Hold Time
4.7
300
250
4.7
4.0
30
µs
ns
ns
µs
µs
ns
Data Setup Time
Clock Low Time
tHIGH
Clock High Time
50
(3)
tSU:CS
SMB_CS Setup Time
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Parameter is specified by characterization and is not tested at production.
6
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
SMBus Timing Specifications (continued)
Over recommended operating supply and temperature ranges unless otherwise specified. (1) (2)
Symbol
tHS:CS
tPOR
Parameter
Conditions
Min
Typ
Max
Units
ns
(3)
(3)
SMB_CS Hold Time
100
Time in which the device must be operational after
power on
500
ms
LVDS Electrical Specifications
Over recommended operating supply and temperature ranges unless otherwise specified.
(1) (2)
Symbol
Parameter
Differential Output Voltage
Conditions
Min
Typ
Max
310
35
Units
mV
VOD
RL = 100Ω
230
Changes in VOD between complimentary output
states
mV
ΔVOD
VOS
ΔVOS
IOS
Offset Voltage
1.125
-50
1.25
1.375
35
V
Change in VOS between complimentary states
Output Short Circuit Current
mV
mA
VOUT = 0V, RL = 100Ω
(3)
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only.
LVDS Timing Specifications
Over recommended operating supply and temperature ranges unless otherwise specified.
(1) (2)
Symbol
tROTR
tROTF
tROCP
tRODC
tRBIT
Parameter
LVDS low-to-high transition time
LVDS high-to-low transition time
LVDS output clock period
Conditions
Min
Typ
300
300
2T
Max
Units
ps
ps
ns
RxCLKOUT Duty Cycle
45
50
55
%
LVDS output bit width
T
ns
tROSC
tROHC
tRODJ
RxOUT Setup to RxCLKOUT OUT
RxOUT Hold to RxCLKOUT OUT
LVDS Output Deterministic Jitter
650
650
800
800
18
ps
ps
RxCLKOUT
(3)
ps
ps
ps
RxOUT0–4
43
2.5
2.5
51
(3)
tRORJ
LVDS Output Random Jitter
RxCLKOUT
(3)
RxOUT0–4
(3)
tROTJ
Peak-to-Peak LVDS Output Jitter
RxCLKOUT
(3)
RxOUT0–4
70
(3)
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Parameter is specified by characterization and is not tested at production.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
LVDS Timing Specifications (continued)
Over recommended operating supply and temperature ranges unless otherwise specified. (1) (2)
Symbol
Parameter
Deserializer Lock Time
Conditions
Min
Typ
Max
Units
ms
(3)
tRLA
1.25 Gbps
2.5 Gbps
3.125 Gbps
22
90
115
20
tLVSK
LVDS Output Skew
LVDS Differential Output Skew
between + and - pins
ps
CML Input Timing Specifications
Over recommended operating supply and temperature ranges unless otherwise specified.
(1) (2)
Symbol
Parameter
Serial Input Jitter Tolerance
Conditions
Min
Typ
Max
Units
TOLJIT
RJ = 0.18 UI
DJ = 0.37 UI
SJ increased until failure
1.25 Gbps
f < 10 kHz
30
f > 1 MHz
0.5
UI
2.5 Gbps
f < 10 kHz
f > 1 MHz
50
0.3
3.125 Gbps
f < 10 kHz
f > 1 MHz
70
0.3
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
CML Input Electrical Specifications
Over recommended operating supply and temperature ranges unless otherwise specified.
(1) (2)
Symbol
VID
Parameter
Differential input voltage
Conditions
Min
230
115
-300
84
Typ
Max
2200
1100
50
Units
mV
mV
μA
(3)
(3)
VIN
Single ended input voltage
Input Current
IIN
RIT
Input Termination
100
116
Ω
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Parameter is specified by characterization and is not tested at production.
8
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
CML Retimed Loop Through Output Electrical Specifications, DS32ELX0124 Only
(1) (2)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Output differential voltage
Conditions
Min
Typ
Max
Units
VLTOD
VOD_CTRL resistor = 9.09 kΩ
1.15
1.45
V
(3)
RLTOT
Output termination
50Ω
75Ω
40
60
50
75
5
60
90
Ω
ΔRLTOT
Mismatch in output termination resistors
%
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Parameter is specified by characterization and is not tested at production.
CML Retimed Loop Through Output Timing Specifications, DS32ELX0124 Only
(1) (2)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
tJIT
Parameter
Conditions
Min
Typ
24
Max
35
Units
ps
(3)
(3)
(3)
Additive Output Jitter
Output Overshoot
tOS
1.5
74
8
%
tLTR
Retimed output driver differential low to high
transition time
105
ps
ps
(3)
(3)
tLTF
Retimed output driver differential high to low
transition time
74
105
15
tLTRFMM
tLTDE
Mismatch in Rise/Fall Time
5
1
%
Retimed driver de-emphasis width
UI
(1) The Electrical and Timing Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except
as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only
and are not ensured.
(2) Typical values represent most likely parametric norms for VCC = +3.3V and TA = +25°C, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Parameter is specified by characterization and is not tested at production.
Timing Diagrams
SMB_CS
t
SU:CS
t
LOW
t
HIGH
t
R
SCK
SDA
t
t
t
t
SU:STA
F
HD:STA
HD:DAT
t
BUF
t
SU:STO
t
SU:DAT
ST
SP
SP
ST
Figure 3. SMBus Timing Parameters
80%
80%
RXCLK
(diff)
20%
ROTR
20%
t
t
ROTF
Figure 4. LVDS Output Transition Time
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
t
/2
ROCP
+100 mV
-100 mV
RXCLK
t
, t
ROCH ROCL
t
ROHC
t
ROSC
Setup
Hold
RX[4:0]
Figure 5. Deserializer (LVDS Interface) Setup/Hold and High/Low Times
3.0V
RESET
t
RPLLS
RxIN
RxCLKOUT
LOCK
t
RLAPL
t
RLA
Figure 6. Reset to Lock Time
Symbol N-1
Symbol N+1
Symbol N+3
Symbol N+4
Symbol N
Symbol N+2
RXIN
t
RD
RXCLK
Symbol N-4
Symbol N-3
Symbol N-2
Symbol N-1
Symbol N
RX[0..4]
Figure 7. Deserializer Propagation Delay
10
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
Last Bit In
First Bit In
High Speed Serial CML Input
Previous Cycle
Current Cycle
Next Cycle
Output Receive Clock
LVDS Data-0
LVDS Data-1
LVDS Data-2
LVDS Data-3
LVDS Data-4
A0
B0
C0
D0
E0
A1
B1
C1
D1
E1
A2
B2
C2
D2
E2
A3
B3
C3
D3
E3
Figure 8. CML to LVDS Bit Map
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
FUNCTIONAL DESCRIPTION
POWER SUPPLIES
The DS32EL0124 and DS32ELX0124 have several power supply pins, at 2.5V as well as 3.3V. It is important
that these pins all be connected and properly bypassed. Bypassing should consist of parallel 4.7μF and 0.1μF
capacitors as a minimum, with a 0.1μF capacitor on each power pin. A 22 μF capacitor is required on the
VDDPLL pin which is connected to the 3.3V rail.
These devices have a large contact in the center on the bottom of the package. This contact must be connected
to the system GND as it is the major ground connection for the device.
POWER UP
It is recommended, although not necessary, to bring up the 3.3V power supply before the 2.5V supply. If the 2.5V
supply is powered up first, an initial current draw of approximately 600mA from the 2.5V rail may occur before
settling to its final value. Regardless of the sequence, both power rails should monotonically ramp up to their final
values.
POWER MANAGEMENT
These devices have two methods to reduce power consumption. To enter the first power save mode, the on
board host FPGA or controlling device can cease to output the DDR transmit clock. To further reduce power, a
write to the power down register will put the device in its lowest power mode.
RESET
There are three ways to reset these devices. A reset occurs automatically during power-up. The device can also
be reset by pulling the RESET pin low, with normal operation resuming when the pin is driven high again. The
device can also be reset by writing to the reset register. This reset will put all of the register values back to their
default values, except it will not affect the address register value if the SMBus default address has been
changed.
LVDS OUTPUTS
The DS32EL0124 and DS32ELX0124 has standard LVDS outputs, compatible with ANSI/TIA/EIA-644. It is
recommended that the PCB trace between the FPGA and the deserializer output be no more than 40-inches.
Longer PCB traces may introduce signal degradation as well as channel skew which could cause serialization
errors. The connection between the host and the DS32EL0124 or DS32ELX0124 should be over a controlled
impedance transmission line with impedance that matches the termination resistor – usually 100Ω. Setup and
hold times are specified in the LVDS Switching Characteristics table, however the clock delay can be adjusted by
writing to register 30’h.
LOOP FILTER
The DS32EL0124 and DSELX0124 have an internal clock data recovery module (CDR), which is used to recover
the input serial data. The loop filter for this CDR is external, and for optimum results, a 30nF capacitor should be
connected between pins 26 and 27. See the Typical Interface Circuit (Figure 14).
LOOP THROUGH DRIVER LAUNCH AMPLITUDE
The launch amplitude of the retimed CML loop through driver is controlled by placing a single resistor from the
VOD_CTRL pin to ground. Use the following equation to obtain the desired VLTOD by selecting the corresponding
resistor value.
R = (1400 mV / VLTOD) x 9.1 kΩ
(1)
The retimed CML loop through driver launch amplitude can also be adjusted by writing to SMBus register 49'h,
bits 3:1. This register is meant to assist system designers during the initial prototype design phase. For final
production, it is recommended that the appropriate resistor value be selected for the desired VLTOD and that
register 49'h be left to its default value.
12
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
REMOTE SENSE
The remote sense feature can be used when a DS32EL0421 or DS32ELX0421 serializer is directly connected to
a DS32EL0124 or DS32ELX0124 deserializer. Active components in the signal path between the serializer and
the deserializer may interfere with the back channel signaling of the devices.
When remote sense is enabled, the deserializer will cycle through five states to successfully establish a link and
align the data. The state diagram for the deserialiezr is shown in Figure 9. The deserialzer will remain in the low
power IDLE state until it receives an input signal. Once the CDR of the deserializer has locked to the input clock,
the device will enter the LINK DETECT state. While in this state, the deserializer will monitor the line to see if the
serializer is sending the training pattern. While in this state, the deserializer will periodically send a link detect
signal upstream to notify the serializer that it can now send the training pattern. When the deserializer detects
that data coming in on the serial line, it will proceed to the CLOCK ACQUISITION state. While in this state the
deserializer will monitor the incoming data for set periods of time in an attempt to extract the clock from the data.
Once, the deserializer has successfully extracted the clock the device will proceed to the LINK ACQUISITION
STATE. In this state the deserializer will perform lane alignment based on the expected training pattern and then
enter the NORMAL state. If the deserializer is unable to successfully lock or maintain lock, it will break the link
sending the serializer back to the IDLE or LINK DETECT states.
DC-BALANCE DECODER
The DS32EL0124 and DS32ELX0124 have a built-in DC-balance decoder to support AC-coupled applications.
When enabled, the output signal RxOUT4+/-, is treated as a data valid bit. If RxOUT4+/- is low, then the data
output from RxOUT0 - RxOUT3 has been successfully decoded using the 8b/10b coding scheme. If RxOUT4+/-
is high and the outputs RxOUT0 - RxOUT3 are high then an invalid 8b/10b code was received, signifying a bit
error. If RxOUT4+/- is high and the outputs RxOUT0 - RxOUT3 are low then an idle character has been
received. The default idle character is a K28.5 code. In order to properly receive other K codes, they must first be
programmed into the deserializer via the SMBus. The SMBus registers allow for only a single programmable
character.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
RxIN does not Exist
or
CDR Not Locked
or
Link Not Acquired
Or
Excessive Bit Errors
Power-On/Reset
IDLE
RxIN
detected
RxIN detected
and
(RS:1, DC_B:0
or
RS:1, DC_B:1)
LINK DETECT
CLOCK
ACQUISITION
Clock
Recovered
CDR Locked
and
(RS:1, DC_B:0
or
RS:1, DC_B:1)
LINK
ACQUISITION
Link
Acquired
NORMAL
Figure 9. Deserializer State Diagram
DESCRAMBLER AND NRZI DECODER
The CDR of the deserializer expects a transition density of 20% for a period of 200 μs. To improve the transition
density of the data, the scrambler and NRZI encoder, which are integrated features in the DS32EL0421 and
DS32ELX0421, serializers can be enabled. If the descrambler is enabled, the serialized data is descrambled
after being recovered by the CDR to according to the polynomial specified in the DS32EL0421 datasheet. Using
the scrambler/descrambler helps to lower EMI emissions by spreading the spectrum of the data. Scrambling also
creates transitions for a deserializer’s CDR to properly lock onto.
The scrambler is enabled or disabled by default depending on how the DC_B and RS pins are configured. To
override the default scrambler setting two register writes must be performed. First, write to register 22’h and set
bit 5 to unlock the descrambler register. Next write to register 21’h and change bit 5 to the desired value. Please
note that NRZI decoder has its own control bits in registers 22'h and 21'h.
14
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
CML INPUT INTERFACING
The DS32ELX0124 has two inputs to support redundancy and failover applications. Either input can be selected
by using the RX_MUX_SEL pin or internal control registers. Whichever input is selected will be routed to the
CDR of the deserializer. Only one input may be selected at a time. Within the CDR, the data is strobed at the
center of the eye diagram(i.e. 0.5UI).
The input stage is self-biased and does not need any external bias circuitry. The DS32EL0124 and
DS32ELX0124 include integrated input termination resistors. These deserializers also support a wide common
mode input from 50mV to Vcc - 50mV and can be DC-coupled where there is no significant Ground potential
difference between the interfacing systems. The serial inputs also provides input equalization control in order to
compensate for loss from the media. The level of equalization is controlled by the SMBus interface. For the
DS32ELX0124, each input can have its own independent equalizer settings.
It is recommended to use RxIN0+/- as the primary input. Due to its close proximity to the loop through driver,
RxIN1 has a typical performance less than RxIN0, with regards to cable length performance. When interfacing to
RxIN1+/- and transmitting with the loop through driver on TxOUT+/-, it is important to follow good layout practices
as described in the LAYOUT GUIDELINES section and in the LVDS Owner’s Manual. Poor layout techniques
can result in excessive cross talk coupled into RxIN1.
CML OUTPUT INTERFACING (DS32ELX0124 ONLY)
The retimed loop through serial outputs of the DS32ELX0124 provide low-skew differential signals. Internal
resistors connected from TxOUT+ and TxOUT- to VDD25 terminate the outputs. The output level can be set by
adjusting the pull-down resistor to the VOD_CTRL pin. The output terminations can also be programmed to be
either 50 or 75 ohms.
The output buffer consists of a current mode logic(CML) driver with user configurable de-emphasis control, which
can be used to optimize performance over a wide range of transmission line lengths and attenuation distortions
resulting from low cost CAT(-5, -6, -7) cable or FR4 backplane. Output de-emphasis is user programmable
through SMBus interface. Users can control the strength of the de-emphasis to optimize for a specific system
environment. Please see the Register Map, register 67'h bits 6:5, for details.
DEVICE CONFIGURATION
There are four ways to configure the DS32EL0124 and DS32ELX0124 devices, these combinations are shown in
Table 2. Refer to Figure 9 to see how the combinations of the RS and DC_B pins change the link startup
behavior of the deserializers. When connecting to a serializer other than the DS32EL0421 or DS32ELX0421,
Remote Sense should be disabled. The descrambler and NRZI decoder shown in Table 2 can be enabled or
disabled through register programming.
When Remote Sense is enabled, with RS pin tied low, the deserializer must be connected directly to a
DS32EL0421/DS32ELX0421 serializer without any active components between them. The Remote Sense
module features both an upstream and downstream communication method for the serializer to detect a
deserializer and vice versa. This feature is used to pass link status information between the 2 devices.
If DC-Balance is enabled, the maximum number of parallel LVDS lanes is four. The fifth lane becomes a Data
Valid signal (TXIN4±). If the Data Valid input to the serializer is logic high, then SYNC characters are transmitted.
If the deserializer receives a SYNC character, then the LVDS data outputs will all be logic low and the Data Valid
outputs will be logic high. If the deserializer detects a DC-Balance code error, the output data pins will be set to
logic high with the Data Valid output also set to logic high.
In the case where DC-Balance is enabled and Remote Sense is disabled, with RS set to high and DC_B set to
low, an external device should toggle the Data Valid input to the serializer periodically to ensure constant lock.
With these pin settings the devices can interface with other active component in the high speed signal path, such
as fiber modules. Every time
a
DS32EL0421/DS32ELX0421 serializer establishes
a
link to
a
DS32EL0124/DS32ELX0124 deserializer with DC-Balance enabled and Remote Sense disabled, the Data Valid
input to the serializer must be held high for 110 LVDS clock periods. This allows the deserializer to extract the
clock and perform lane alignment while skipping the LINK ACQUISITION state.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
When both Remote Sense and DC-Balance are disabled, RS and DC_B pins set to high, the LVDS lane
alignment is not maintained. In this configuration, data formatting is handled by an FPGA or external source. In
this mode the deserializer locks to incoming random data. To achieve lock during the clock acquisition phase, the
incoming data should have a transition density of approximately 20% for a period of 200 µs. Scrambling and
NRZI encoding can be implemented to help improve the transition density of the data. This pin setting also allows
for the devices to interface with other active components in the high speed signal path.
Table 2. Device Configuration Table
Remote Sense Pin (RS)
DC-Balance Pin (DC_B)
Configuration
0
0
1
1
0
1
0
1
Remote Sense enabled
DC-Balance enabled
Data Alignment
De-Scrambler and NRZI decoder disabled by default
Remote Sense enabled
DC-Balance disabled
Data Alignment
De-Scrambler and NRZI decoder enabled by default
Remote Sense disabled
DC-Balance enabled
Data Alignment
De-Scrambler and NRZI decoder enabled by default
Remote Sense disabled
DC-Balance disabled
No Data Alignment
De-Scrambler and NRZI decoder disabled by default
SMBus INTERFACE
The System Management Bus interface is compatible to SMBus 2.0 physical layer specification. The use of the
Chip Select signal is required. Holding the SMB_CS pin HIGH enables the SMBus port, allowing access to the
configuration registers. Holding the SMB_CS pin LOW disables the device's SMBus, allowing communication
from the host to other slave devices on the bus. In the STANDBY state, the System Management Bus remains
active. When communication to other devices on the SMBus is active, the SMB_CS signal for the deserializer
must be driven LOW.
The address byte for all DS32EL0124 and DS32ELX0124 devices is B0'h. Based on the SMBus 2.0
specification, these devices have a 7-bit slave address of 1011000'b. The LSB is set to 0'b (for a WRITE), thus
the 8-bit value is 1011 0000'b or B0'h.
The SCK and SDA pins are 3.3V LVCMOS signaling and include high-Z internal pull up resistors. External low
impedance pull up resistors maybe required depending upon SMBus loading and speed. Note, these pins are not
5V tolerant.
Transfer of Data via the SMBus
During normal operation the data on SDA must be stable during the time when SCK is HIGH.
There are three unique states for the SMBus:
START
STOP
IDLE
A HIGH to LOW transition on SDA while SCK is HIGH indicates a message START condition.
A LOW to HIGH transition on SDA while SCK is HIGH indicates a message STOP condition.
If SCK and SDA are both HIGH for a time exceeding tBUF from the last detected STOP condition or if they are HIGH for a total
exceeding the maximum specification for tHIGH then the bus will transfer to the IDLE state.
SMBus Transactions
The devices support WRITE and READ transactions. See Register Map for register address, type (Read/ Write,
Read Only), default value and function information.
Writing to a Register
The devices support WRITE and READ transactions. See Register Map for register address, type (Read/ Write,
Read Only), default value and function information.
16
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
1. The Host (Master) selects the device by driving its SMBus Chip Select (SMB_CS) signal HIGH.
2. The Host drives a START condition, the 7-bit SMBus address, and a “0” indicating a WRITE.
3. The Device (Slave) drives the ACK bit (“0”).
4. The Host drives the 8-bit Register Address.
5. The Device drives an ACK bit (“0”).
6. The Host drive the 8-bit data byte.
7. The Device drives an ACK bit (“0”).
8. The Host drives a STOP condition.
9. The Host de-selects the device by driving its SMBus CS signal Low.
The WRITE transaction is completed, the bus goes IDLE and communication with other SMBus devices may
now occur.
Reading a Register
To read a register, the following protocol is used (see SMBus 2.0 specification).
1. The Host (Master) selects the device by driving its SMBus Chip Select (SMB_CS) signal HIGH.
2. The Host drives a START condition, the 7-bit SMBus address, and a “0” indicating a WRITE.
3. The Device (Slave) drives the ACK bit (“0”).
4. The Host drives the 8-bit Register Address.
5. The Device drives an ACK bit (“0”).
6. The Host drives a START condition.
7. The Host drives the 7-bit SMBus Address, and a “1” indicating a READ.
8. The Device drives an ACK bit “0”.
9. The Device drives the 8-bit data value (register contents).
10. The Host drives a NACK bit “1”indicating end of the READ transfer.
11. The Host drives a STOP condition.
12. The Host de-selects the device by driving its SMBus CS signal Low.
The READ transaction is completed, the bus goes IDLE and communication with other SMBus devices may now
occur.
SMBus Configurations
Many different configurations of the SMBus are possible and depend upon the specific requirements of the
applications. Several possible applications are described.
Configuration 1
The deserializer SMB_CS may be tied High (always enabled) since it is the only device on the SMBus. See
Figure 10.
Configuration2
Since the multiple SER devices have the same address, the use of the individual SMB_CS signals is required.
To communicate with a specific device, its SMB_CS is driven High to select the device. After the transaction is
complete, its SMB_CS is driven Low to disable its SMB interface. Other devices on the bus may now be selected
with their respective chip select signals and communicated with. See Figure 11.
Configuration 3
The addressing field is limited to 7-bits by the SMBus protocol. Thus it is possible that multiple devices may
share the same 7-bit address. An optional feature in the SMBus 2.0 specification supports an Address Resolution
Protocol (ARP). This optional feature is not supported by the DS32EL0124/DS32ELX0124 devices. Solutions for
this include: the use of the independent SMB_CS signals, independent SMBus segments, or other means.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
3V3
SMBus
Device
FPGA
Host
3V3
Figure 10. SMBus Configuration 1
SMBus
Device
SMBus
Device
SMBus
Device
FPGA
Host
3V3
Figure 11. SMBus Configuration 2
SMBus
Device
SMBus
Device
SMBus
Device
FPGA
Host
3V3
3V3
3V3
3V3
Figure 12. SMBus Configuration 3
18
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
PROPAGATION DELAY
Once the deserializer is locked, the amount of time it takes for a signal to travel from the high speed CML serial
input through the device and out via the DDR LVDS interface is defined to be the propagation delay. The
propagation delay through the DS32EL0124/DS32ELX0124 due to the analog circuitry is considered negligible
compared to the time delay caused by the digital components. The information presented in this section allows
system designers to predict the propagation delay through the device in terms of clock cycles which are
proportional to the high speed serial line rate.
Each clock cycle shown inFigure 13 is defined to be 1/20th of the high speed serial bit rate. For example, at a
serial line rate of 3.125 Gbps the clock frequency of each delay cycle would be 156.25 MHz. Note, this is not the
same frequency as the LVDS outputs, which would be 312.5 MHz for a serial line rate of 3.125 Gbps. Dashed
lines in Figure 13 indicate that the feature is disabled by default in that mode and therefore add no more time to
the total propagation delay. In the last row, bypassed indicates that the data is sampled even though the feature
is disabled by default. The sampling of the data results in an added amount of propagation delay as specified in
the box.
Lane
Alignment
Logic
Total
Propagation
Delay
Config Pins
(RS, DC_B)
DC Balance
Decoder
LVDS
Interface
NRZ Decoder
Descrambler
CML Interface
Data Flow
0, 0
2 clocks
2 clocks
3 clocks
3 clocks
1 clock
1 clock
3-4 clocks
3-4 clocks
3-4 clocks
3-4 clocks
9-10 clocks
11-12 clocks
10-11 clocks
10-11 clocks
0, 1
1, 0
1, 1
1 clock
1 clock
1 clock
1 clock
2 clocks
2 clocks
3 clocks
3 clocks
1 clock
(bypassed)
1 clock
(bypassed)
Figure 13. Deserializer Propagation Delay
PROPAGATION DELAY FOR RETIMED LOOP THROUGH DRIVER — DS32ELX0124 ONLY
If the loop through driver is enabled in the DS32ELX0124, the propagation delay can also be defined as the
amount of time it takes a signal to pass from the high speed CML serial input to the retimed loop through driver
output. This time delay is measured in CDR clock cycles. The CDR clock frequency is equal to high speed serial
line rate or one high speed serial bit width. For example, if the high speed serial line rate is 3.125 Gbps, then the
CDR clock frequency is 3.125 GHz. The propagation delay from the high speed input to the loop through driver
output is 1 CDR clock.
Applications Information
GPIO PINS
The GPIO pins can be useful tools when debugging or evaluating the system. For specific GPIO configurations
and functions refer to registers 2, 3, 4, 5 and 6 in the device register map.
GPIO pins are commonly used when there are multiple deserializers on the same SMBus. In order to program
individual settings into each serializer, they will each need to have a unique SMBus address. To reprogram
multiple deserializers on a single SMBus, configure the first deserializer such that the SMBus lines are connected
to the FPGA or host controller. The CS pin of the second serializer should be tied to GPIO0 of the first
deserializer, with the CS pin of the next deseriazlier tied to GPIO0 of its preceding deserializer. By holding all of
the GPIO0 pins low, the first deserializer’s address may now be reprogrammed by writing to register 0. The first
deserializer’s GPIO pin can now be asserted and the second deserializer’s address may now be reprogrammed.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
HIGH SPEED COMMUNICATION MEDIA
Using the deserializer’s integrated equalizer blocks in combination with the DS32EL0421 or DS32ELX0421’s
integrated de-emphasis block allows data to be transmitted across a variety of media at high speeds. Factors
that can limit device performance include excessive input clock jitter, noisy power rails, EMI from nearby noisy
components and poor layout techniques. Although many cables contain wires of similar gauge and shielding,
performance can vary greatly depending on the quality of the connector.
The DS32ELX0124 also has a programmable de-emphasis block on its retimed loop through output TxOUT+/-.
The de-emphasis setting for the loop through driver is programmed through the SMBus.
REDUNDANCY APPLICATIONS
The DS32ELX0124 has two high speed CML serial inputs. SMBus register control allows the host device to
monitor for errors or link loss on the active input channel. This enables the host device, usually an FPGA, to
switch to the secondary input if problems occur with the primary input.
LINK AGGREGATION
Multiple DS32EL0421/DS32ELX0421 serializers and D32EL0124/DS32ELX0124 deserializers can be
aggregated together if an application requires a data throughput of more than 3.125 Gbps. By utilizing the data
valid signal of each device, the system can be properly deskewed to allow for a single cable, such as CAT-6,
DVI-D, or HDMI, to carry data payloads beyond 3.125 Gbps.
Link aggregation configurations can also be implemented in applications which require longer cable lengths. In
these type of applications the data rate of each serializer and deserializer chipset can be reduced, such that the
applications' net data throughput is still the same. Since each high speed channel is now operating at a fraction
of the original data rate, the loss over the cable is reduced, allowing for greater lengths of cable to be used in the
system.
For more information regarding link aggregation please see Application Note 1887, Expanding the Payload with
TI's FPGA-Link DS32ELX0421 and DS32ELX0124 Serializer and Deserializer.
REACH EXTENSION
The DS32ELX0124 deserializer contains a retimed loop through CML serial output. The loop through driver also
has programmable de-emphasis making this device capable of reach extension applications.
DAISY CHAINING
The loop through driver of the DS32ELX0124 deserializer can be used to string together deserializers in a daisy
chain configuration. This allows a single data source such as a DS32EL0421 serializer to communicate to
multiple receiving systems.
LAYOUT GUIDELINES
It is important to follow good layout practices for high speed devices. The length of LVDS input traces should not
exceed 40 inches. In noisy environments the LVDS traces may need to be shorter to prevent data corruption due
to EMI. Noisy components should not be placed next to the LVDS or CML traces. The LVDS and CML traces
must have a controlled differential impedance of 100Ω. Do not place termination resistors at the CML inputs or
output, the DS32EL0124 and DS32ELX0124 have internal termination resistors. It is recommended to avoid
using vias. Each pair of vias creates an impedance mismatch in the transmission line and result in reflections,
which can greatly lower the maximum distance of the high speed data link. If vias are required, they should be
placed symmetrically on each side of the differential pair. For more tips and detailed suggestions regarding high
speed board layout principles, please consult the LVDS Owner’s Manual.
20
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
2.5V 3.3V
0.1 mF
0.1 mF
7, 25,
35
1, 15, 18,
28, 36
49
16
47
+
+
-
RXIN0
RXOUT4
-
48
45
17
19
+
-
RXOUT3
RXOUT2
RXOUT1
RXOUT0
+
RXIN1
46
43
-
20
+
-
3.3V
44
41
28
VDDPLL
+
-
42
39
22 mF
DS32ELX0124
+
-
9.1 kW
40
37
14
VOD_CTRL
+
-
RXCLKOUT
38
27
26
LF_CP
30 nF
30
31
RESET
LOCK
LF_REF
3
4
GPIO0
GPIO1
GPIO2
32
33
34
SDA
SCK
11
SMB_CS
5
6
21
22
3.3V
3.3V
0.1 mF
0.1 mF
Figure 14. Typical Interface Circuit
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics
The eye diagrams shown below illustrate the typical performance of the DS32ELX0124/DS32EL0124 configured with RS = 0,
DC_B = 0, for the conditions listed below each figure. The PRBS-15 data was generated by a low cost FPGA, which used an
LMK03000C to generate the various clock frequencies. The data was then sent to a DS32ELX0421 configured with RS = 0,
DC_B = 0, which transmitted the data across the specified cable type and length at the specified data rate. The signal
conditioning settings used for each measurement are also listed below the figures.
Figure 15. LVDS RxCLKOUT Output
(1.25 Gbps, 40m CAT-5e, 0x000 DS32ELX0124 EQ setting,
0x10 DS32EL0421 De-Emphasis setting)
Figure 16. LVDS RxOUT0 Output
(1.25 Gbps, 40m CAT-5e, 0x000 DS32ELX0124 EQ setting,
0x10 DS32EL0421 De-Emphasis setting)
Figure 17. LVDS RxCLKOUT Output
(3.125 Gbps, 20m CAT-6 SCTP, 0x001 DS32ELX0124 EQ
setting, 0x10 DS32EL0421 De-Emphasis setting)
Figure 18. LVDS RxOUT0 Output
(3.125 Gbps, 20m CAT-6 SCTP, 0x001 DS32ELX0124 EQ
setting, 0x10 DS32EL0421 De-Emphasis setting)
22
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
Typical Performance Characteristics (continued)
The eye diagrams shown below illustrate the typical performance of the DS32ELX0124/DS32EL0124 configured with RS = 0,
DC_B = 0, for the conditions listed below each figure. The PRBS-15 data was generated by a low cost FPGA, which used an
LMK03000C to generate the various clock frequencies. The data was then sent to a DS32ELX0421 configured with RS = 0,
DC_B = 0, which transmitted the data across the specified cable type and length at the specified data rate. The signal
conditioning settings used for each measurement are also listed below the figures.
Figure 19. Retimed Loop Through Output
(1.25 Gbps, 40m CAT-5e, 0x000 DS32ELX0124 EQ setting,
0x10 DS32EL0421 De-Emphasis setting)
Figure 20. Retimed Loop Through Output
(3.125 Gbps, 20m CAT-6 SCTP, 0x001 DS32ELX0124 EQ
setting, 0x10 DS32EL0421 De-Emphasis setting)
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
Register Map
The register information for the deserializer is shown in the table below. Some registers have been omitted or
marked as reserved; these are for internal testing and should not be written to. Some register bits require an
override bit to be set before they can be written to.
Addr (Hex)
00
Name
Bits
7:1
Field
R/W
R/W
Default
58'h
Description
Device ID
SMBus Address
Some systems will use all 8 bits as the device
ID. This will shift the value from 58’h to B0’h
0
Reserved
0
0
0
0
01
02
Reset
7:1
0
Reserved
Software Reset
GPIO0 Mode
R/W
R/W
Reset the device. Does not affect device ID.
GPIO0 Config 7:4
0000: GP Out
0001: Signal Detect RxIN0
0010: BIST Status
All Others: Reserved
3:2
GPIO0 R Enable
R/W
01'b
00: Pullup/Pulldown disabled
01: Pulldown Enabled
10: Pullup Enabled
11: Reserved
1
0
Input Enable
Output Enable
GPIO1 Mode
R/W
R/W
R/W
0
0: Input buffer disabled
1: Input buffer enabled
1'b
0
0: Output Tri-State™
1: Output enabled
03
GPIO1 Config 7:4
0000: Power On Reset
0001: GP Out
0010: Signal Detect RxIN1
0011:CDR Lock
All Others: Reserved
3:2
GPIO1 R Enable
R/W
01'b
00: Pullup/Pulldown disabled
01: Pulldown Enabled
10: Pullup Enabled
11: Reserved
1
0
Input Enable
Output Enable
GPIO2 Mode
R/W
R/W
R/W
0
1
0
0: Input buffer disabled
1: Input buffer enabled
0: Output Tri-State™
1: Output enabled
04
GPIO2 Config 7:4
0000: GP Out
0001: Always on Clock Out
0010: LVDS Tx CLK
0011: CDR CLK
All Others: Reserved
3:2
GPIO2 R Enable
R/W
01'b
00: Pullup/Pulldown disabled
01: Pulldown Enabled
10: Pullup Enabled
11: Reserved
1
0
Input Enable
R/W
R/W
0
0: Input buffer disabled
1: Input buffer enabled
Output Enable
1'b
0: Output Tri-State™
1: Output enabled
05
06
GP In
7:3
2
Reserved
GP In 2
R
R
R
0
0
0
0
0
0
0
Input value on GPIO2
Input value on GPIO1
Input value on GPIO0
1
GP In 1
0
GP In 0
GP Out
7:3
2
Reserved
GP Out 2
GP Out 1
GP Out 0
R/W
R/W
R/W
Output value on GPIO2
Output value on GPIO1
Output value on GPIO0
1
0
07 — 1F Reserved
24 Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
Addr (Hex)
Name
Bits
Field
R/W
Default
Description
20
Device Config
0
7
LVDS Always On Clock R/W
0
1: Disable
0: When not locked switch to Always On
Clock
6:3
2
Reserved
0
0
Reverse Data Order
R/W
0: Normal
1: Reverse output data order
1
0
Reset Channel
R/W
R/W
0
0
Reset input high speed channel
Digital Power Down
Power down parallel, seria-to-parallell, and
always on clock
21
Device Config
1
7
6
Reserved
0
0
NRZI Decode Enable
R/W
R/W
R/W
R/W
R/W
R/W
Enable NRZI decoding of incoming data;
requires an override bit
5
Descramble Enable
Rx Mux
0
0
0
0
0
Enabled the descrambler, requires an
override bit
4
RX_MUX_SEL control register. requires an
override bit
3
Decode Bypass
Bypass DC Balance decoder. requires an
override bit
2
Training Sequence
Enable
Enable training sequence. requires an
override bit
1:0
Device Configuartion
MSB: Remote Sense enable, active low
LSB: DC balance encoder enable, active low
requires an override bit
22
Device Config
Override
7
6
5
4
3
2
1
0
Reserved
0
0
0
0
0
0
0
0
NRZ Override
Descramble Override
Rx Mux Override
Reserved
R/W
R/W
R/W
Unlock bit 6 of register 21'h
Unlock bit 5 of register 21'h
Unlock bit 4 of register 21'h
Decode Bypass Override R/W
Unlock bit 3 of register 21'h
Unlock bit 2 of register 21'h
Unlock bits 1 and 0 of register 21'h
Traning Override
R/W
R/W
Device Config Override
23 — 26 Reserved
27 LVDS Per
7
LVDS VOD High
R/W
0
0: LVDS VOD normal operation. Setting used
in Electrical Characteristics Table
1: Increases VOD. Allows for longer traces to
be driven, but consume more power
Channel
Enable
6
LVDS Control
R/W
0
1: Allow SMBus to control LVDS per channel
enable
5
4
3
2
1
0
7
6
5
RxCLKOUT Enable
RxOUT4 Enable
RxOUT3 Enable
RxOUT2 Enable
RxOUT1 Enable
RxOUT0 Enable
Reserved
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
1
Enables RxCLKOUT output driver
Enables RxOUT4 output driver
Enables RxOUT3 output driver
Enables RxOUT2 output driver
Enables RxOUT1 output driver
Enables RxOUT0 output driver
28
LVDS Config
LVDS Reset
R/W
R/W
Resets LVDS block
LVDS Clock Rate
0:RxCLKOUT is DDR/2
1: RxCLKOUT is DDR
4
LVDS Clock Invert
LVDS Clock Delay
R/W
R/W
0
Inverts the polarity of the RxCLKOUT signal
3:2
10'b
00: 160 ps
11: -80 ps
80 ps step size
1:0
Reserved
0
29 — 2A Reserved
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
Addr (Hex)
2B
Name
Bits
7:4
Field
R/W
Default
Description
Event Config
Reserved
Event Count Select
0
0
3
R/W
0: Select CDR Event Counter for reading.
Events include loss of signal detect or loss of
CDR lock.
1: Select Data Event Counter for reading
2
1
0
Reset CDR Error Count R/W
0
0
0
Resets CDR event count
Reset data event count
Enable event coutners
Reset Link Error Count
Enable Count
R/W
R/W
2C
2D
Reserved
Error Monitor
7:5
4
Reserved
0
0
0
Accumulate Error Enable R/W
1: Enable counting accumulation of errors
3
8b/10b Error disable
Clear Event Counter
Select Error Count
R/W
R/W
R/W
1: Disables 8b/10b decode errors from being
counted or flagged on LOCK pin
2
1
0
0
1: clears errors in both the current and
previous state of teh errors count
0: Number of errors in current run
1: Number of errors within the selected timing
window
0
Normal Error Disable
Error Threshold
R/W
R/W
0
1: Disable exiting NORMAL state when the
number of errors exceeds the error threshold
2E
2F
Error
Threshold
LSBs
7:0
10'h
0
Error threshold above which part stops
transmittion of data — LSB
Error
7:0
Error Threshold
R/W
Error threshold above which part stops
transmittion of data — MSB
Threshold
MSBs
30 — 3A Reserved
3B
Data Rate
7
Reserved
0
6:4
Frequency Range
R
111'b
001: Reserved
010: 1 — 1.3 Gbps
011: 1.2 — 1.8 Gbps
100: 1.5 — 2.1 Gbps
101: 1.9 — 2.7 Gbps
110: 2.4 — 3.2 Gbps
111: No Lock
3:2
BIST Status
R
0
00: BIST passed
01: BIST failed to capture PREAMBLE
10: BIST pattern mode failed
11: BIST data sequence failed
1
0
BIST Done
R
R
0
0
BIST pattern done. Set when not using
repeat.
BIST Allign Done
Alignment of incoming data done
3C
3D
3E
Reserved
Event Status
7:0
7:0
Event Count
R
R
0
0
Count of errors that caused a loss of link
Number of errors in data — LSB
Error Status
LSBs
Data Error Count
3F
Errors Status
MSBs
7:0
Data Error Count
R
0
Number of errors in data — MSB
40 — 49 Reserved
26
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
www.ti.com
SNLS284K –MAY 2008–REVISED APRIL 2013
Addr (Hex)
Name
Bits
Field
R/W
Default
Description
49
Loop Through 7:5
Reserved
Termination Select
0
1
Driver Config
4
R/W
0: 75Ω
1: 50 Ω
3:1
Output Amplitude Adjust R/W
011'b
000: Level 7
001: Level 8 (Highest output)
010: Level 5
011: Level 6 (Normal output)
100: Level 4
101: Level 3
110: Level 2
111: Level 1 (Lowest output)
0
Reserved
Reserved
0
0
0
0
0
60
EQ Attenuator 7:4
3
2
1
Attenuator 0 Override
Attenuator 1 Override
Attenuator 0 Enable
R/W
R/W
R/W
Overrides attenuation control in EQ 0
Overrides attenuation control in EQ 1
1: enables attenuatorfor for EQ 0. Requires bit
3 to be set
0
Attenuator 1 Enable
EQ 0 Boost Control
R/W
0
0
Enables attenuato for EQ 1. Requires bit 2 to
be set.r
61
EQ Boost
Control
7:5
4:2
1:0
Sets EQ level for RxIN0. Requires override bit
000: Off
x10: Low (or 110)
x01: Mid (or 101)
x11: High (or 111)
EQ 1 Boost Control
Reserved
0
Sets EQ level for RxIN1. Requires override bit
000: Off
x10: Low (or 110)
x01: Mid (or 101)
x11: High (or 111)
0
62
63
Reserved
EQ Override
Control
7
Reserved
1
1
1
0
0
6
Reserved
5
EQ 0 Enable
EQ 1 Enable
Reserved
R/W
R/W
1: Enables EQ for RxIN0
1: Enables EQ for RxIN1
4
3:0
64 — 66 Reserved
67 LT De-
7
Reserved
0
0
Emphasis
Control
6:5
De-Emphasis Setting
00: Off
01: Low
10: Med
11: Max
4:0
Reserved
0
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Links: DS32EL0124 DS32ELX0124
DS32EL0124, DS32ELX0124
SNLS284K –MAY 2008–REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision J (April 2013) to Revision K
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 24
28
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: DS32EL0124 DS32ELX0124
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
DS32EL0124SQ/NOPB
DS32EL0124SQE/NOPB
DS32EL0124SQX/NOPB
DS32ELX0124SQE/NOPB
DS32ELX0124SQX/NOPB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
WQFN
WQFN
WQFN
WQFN
WQFN
RHS
RHS
RHS
RHS
RHS
48
48
48
48
48
1000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
SN
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-3-260C-168 HR
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
32EL0124
SN
SN
SN
SN
32EL0124
32EL0124
32ELX0124
32ELX0124
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
DS32EL0124SQ/NOPB
WQFN
RHS
RHS
RHS
RHS
RHS
48
48
48
48
48
1000
250
330.0
178.0
330.0
178.0
330.0
16.4
16.4
16.4
16.4
16.4
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
7.3
1.3
1.3
1.3
1.3
1.3
12.0
12.0
12.0
12.0
12.0
16.0
16.0
16.0
16.0
16.0
Q1
Q1
Q1
Q1
Q1
DS32EL0124SQE/NOPB WQFN
DS32EL0124SQX/NOPB WQFN
DS32ELX0124SQE/NOPB WQFN
DS32ELX0124SQX/NOPB WQFN
2500
250
2500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
DS32EL0124SQ/NOPB
DS32EL0124SQE/NOPB
DS32EL0124SQX/NOPB
DS32ELX0124SQE/NOPB
DS32ELX0124SQX/NOPB
WQFN
WQFN
WQFN
WQFN
WQFN
RHS
RHS
RHS
RHS
RHS
48
48
48
48
48
1000
250
356.0
208.0
356.0
208.0
356.0
356.0
191.0
356.0
191.0
356.0
35.0
35.0
35.0
35.0
35.0
2500
250
2500
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明