DS75161AWM [TI]
OCTAL LINE TRANSCEIVER, PDSO20, PACKAGE-20;
| 型号： | DS75161AWM |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | OCTAL LINE TRANSCEIVER, PDSO20, PACKAGE-20 驱动 光电二极管 接口集成电路 驱动器 |
| 文件： | 总12页 (文件大小：246K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DS75160A,DS75161A
DS75160A/DS75161A IEEE-488 GPIB Transceivers
Literature Number: SNOSBL5A
May 1999
DS75160A/DS75161A
IEEE-488 GPIB Transceivers
General Description
This family of high-speed-Schottky 8-channel bi-directional
transceivers is designed to interface TTL/MOS logic to the
IEEE Standard 488-1978 General Purpose Interface Bus
(GPIB). PNP inputs are used at all driver inputs for minimum
loading, and hysteresis is provided at all receiver inputs for
added noise margin. The IEEE-488 required bus termination
is provided internally with an active turn-off feature which
disconnects the termination from the bus when VCC is re-
moved.
Features
n 8-channel bi-directional non-inverting transceivers
n Bi-directional control implemented with TRI-STATE®
output design
n Meets IEEE Standard 488-1978
n High-speed Schottky design
n Low power consumption
n High impedance PNP inputs (drivers)
n 500 mV (typ) input hysteresis (receivers)
n On-chip bus terminators
n No bus loading when VCC is removed
n Pin selectable open collector mode on DS75160A driver
outputs
The General Purpose Interface Bus is comprised of 16 sig-
nal lines — 8 for data and 8 for interface management. The
data lines are always implemented with DS75160A, and the
management lines are either implemented with DS75161A in
a single-controller system.
n Accommodates multi-controller systems
Connection Diagrams
Dual-In-Line Package
Dual-In-Line Package
DS005804-16
Order Number DS75161AN or DS75161AWM
See NS Package Number M20B or N20B
DS005804-1
Top View
Order Number DS75160AN or DS75160AWM
See NS Package Number M20B or N20A
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 2001 National Semiconductor Corporation
DS005804
www.national.com
Absolute Maximum Ratings (Note 2)
Molded Package
1897 mW
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Min
4.75
0
Max
5.25
70
Units
V
VCC, Supply Voltage
TA, Ambient Temperature
IOL, Output Low Current
Bus
˚C
Supply Voltage, VCC
7.0V
5.5V
Input Voltage
48
16
mA
mA
Storage Temperature Range
Lead Temperature (Soldering, 4 sec.)
−65˚C to +150˚C
260˚C
Terminal
Note 1: Derate molded package 15.2 mW/˚C above 25˚C.
Maximum Power Dissipation (Note 1) at 25˚C
Electrical Characteristics (Notes 3, 4)
Symbol
Parameter
High-Level Input Voltage
Low-Level Input Voltage
Input Clamp Voltage
Conditions
Min
Typ
Max Units
VIH
2
V
VIL
0.8
V
V
VIK
II = −18 mA
−0.8 −1.5
VHYS
VOH
Input Hysteresis
High-Level
Bus
400
2.7
2.5
500
3.5
3.4
mV
V
Terminal
IOH = −800 µA
IOH = −5.2 mA
IOL = 16 mA
IOH = 48 mA
VI = 5.5V
Output Voltage
Low-Level
Bus (Note 4)
Terminal
VOL
0.3
0.4
0.2
0.1
0.5
0.5
100
20
V
µA
µA
V
Output Voltage
High-Level
Bus
IIH
Terminal and
TE, PE, DC,
SC Inputs
Input Current
Low-Level
VI = 2.7V
IIL
VI = 0.5V
−10 −100
Input Current
Terminator Bias
Voltage at Bus Port
Terminator
VBIAS
Driver
II(bus) = 0 (No Load)
2.5
3.0
3.7
Disabled
ILOAD
VI(bus) = −1.5V to 0.4V
VI(bus) = 0.4V to 2.5V
VI(bus) = 2.5V to 3.7V
−1.3
0
Bus Loading
Current
−3.2
2.5
Bus
Driver
mA
Disabled
−3.2
2.5
VI(bus) = 3.7V to 5V
VI(bus) = 5V to 5.5V
0
0.7
2.5
VCC = 0V, VI(bus) = 0V to 2.5V
VI = 2V, VO = 0V (Note 5)
40
µA
IOS
Short-Circuit
Terminal
−15
−35
−35
−75
mA
Output Current
Supply Current
Bus (Note 6)
DS75160A
−75 −150
ICC
Transmit, TE = 2V, PE = 2V, VI = 0.8V
Receive, TE = 0.8V, PE = 2V, VI = 0.8V
TE = 0.8V, DC = 0.8V, VI = 0.8V
VCC = 5V or 0V, VI = 0V to 2V,
f = 1 MHz
85
70
84
20
125
100
125
30
mA
pF
DS75161A
Bus
CIN
Bus-Port
Capacitance
Note 2: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.
Note 3: Unless otherwise specified, min/max limits apply across the 0˚C to +70˚C temperature range and the 4.75V to 5.25V power supply range. All typical values
are for T = 25˚C and V
= 5.0V.
CC
A
Note 4: All currents into device pins are shown as positive; all currents out of device pins are shown as negative; all voltages are referenced to ground, unless
otherwise specified. All values shown as max or min are so classified on absolute value basis.
Note 5: Only one output at a time should be shorted.
Note 6: This characteristic does not apply to outputs on DS75161A that are open collector.
www.national.com
2
Switching Characteristics (Note 7)
±
VCC = 5.0V 5%, TA = 0˚C to 70˚C
Symbol
Parameter
From
To
Conditions
DS75160A
DS75161A
DS75162A Units
Min Typ Max Min Typ Max Min Typ Max
tPLH
tPHL
tPLH
tPHL
tPZH
tPHZ
Propagation Delay Time,
Low to High Level Output
Propagation Delay Time,
High to Low Level Output
Propagation Delay Time,
Low to High Level Output
Propagation Delay Time,
High to Low Level Output
Output Enable Time
VL = 2.3V
RL = 38.3Ω
CL = 30 pF
Figure 1
10 20
14 20
14 20
10 20
19 32
15 22
10 20
14 20
14 20
10 20
23 40
15 25
10 20
14 20
14 20
10 20
23 40
15 25
ns
ns
ns
ns
ns
ns
Terminal Bus
VL = 5.0V
Bus
Terminal RL = 240Ω
CL = 30 pF
Figure 2
VI = 3.0V
to High Level
VL = 0V
Output Disable Time
TE, DC,
or SC
RL = 480Ω
CL = 15 pF
Figure 1
From High Level
tPZL
Output Enable Time
to Low Level
(Note 8)
(Note 9)
Bus
VI = 0V
24 35
17 25
28 48
17 27
28 48
17 27
ns
ns
VL = 2.3V
RL = 38.3Ω
CL = 15 pF
Figure 1
tPLZ
Output Disable Time
From Low Level
tPZH
Output Enable Time
to High Level
VI = 3.0V
VL = 0V
17 33
15 25
18 40
22 33
18 40
22 33
ns
ns
tPHZ
Output Disable Time
From High Level
TE, DC,
or SC
RL = 3 kΩ
Terminal CL = 15 pF
Figure 1
tPZL
Output Enable Time
to Low Level
(Note 8)
(Note 9)
VI = 0V
25 39
15 27
28 52
20 35
28 52
20 35
ns
ns
VL = 5V
tPLZ
Output Disable Time
From Low Level
RL = 280Ω
CL = 15 pF
Figure 1
tPZH
Output Pull-Up Enable
Time (DS75160A Only)
Output Pull-Up Disable
Time (DS75160A Only)
VI = 3V
10 17
10 15
NA
NA
NA
NA
ns
ns
PE
Bus
VL = 0V
tPHZ
(Note 8)
RL = 480Ω
CL = 15 pF
Figure 1
Note 7: Typical values are for V
= 5.0V and T = 25˚C and are meant for reference only.
A
CC
Note 8: Refer to Functional Truth Tables for control input definition.
Note 9: Test configuration should be connected to only one transceiver at a time due to the high current stress caused by the V voltage source when the output
I
connected to that input becomes active.
3
www.national.com
Switching Load Configurations
DS005804-8
V
V
logic high = 3.0V
logic low = 0V
C
C
*C includes jig and probe capacitance
L
DS005804-9
FIGURE 1.
V
V
logic high = 3.0V
logic low = 0V
C
C
*C includes jig and probe capacitance
L
FIGURE 2.
Connection Diagrams
Dual-In-Line Package
DS005804-2
Top View
This device is also an 8-channel bi-directional transceiver
which is specifically configured to implement the eight man-
agement signal lines of the IEEE-488 bus. This device,
paired with the DS75160A, forms the complete 16-line inter-
face between the IEEE-488 bus and a single controller in-
strumentation system. In compliance with the system orga-
nization of the management signal lines, the SRQ, NDAC,
and NRFD bus port outputs are open collector. In contrast to
the DS75160A, these open collector outputs are a fixed
configuration. The direction control is divided into three
groups. The DAV, NDAC, and NRFD transceiver directions
are controlled by the TE input. The ATN, SRQ, REN, and IFC
transceiver directions are controlled by the DC input. The
EOI transceiver direction is a function of both the TE and DC
inputs, as well as the logic level present on the ATN channel.
The port connections to the bus lines have internal termina-
tors identical to the DS75160A.
Functional Description
DS75160A
This device is an 8-channel bi-directional transceiver with
one common direction control input, denoted TE. When used
to implement the IEEE-488 bus, this device is connected to
the eight data bus lines, designated DIO1–DIO8. The port
connections to the bus lines have internal terminators, in
accordance with the IEEE-488 Standard, that are deacti-
vated when the device is powered down. This feature guar-
antees no bus loading when VCC = 0V. The bus port outputs
also have a control mode that either enables or disables the
active upper stage of the totem-pole configuration. When
this control input, denoted PE, is in the high state, the bus
outputs operate in the high-speed totem-pole mode. When
PE is in the low state, the bus outputs operate as open
collector outputs which are necessary for parallel polling.
DS75161A
www.national.com
4
Functional Description (Continued)
Logic Diagrams
Table of Signal Line Abbreviations
DS75160A
Signal Line Mne-
Classi-
fication
monic
Definition
Device
DC
Direction Control
DS75161A
Control
PE
TE
SC
Pull-Up Enable
Talk Enable
DS75160A
All
Signals
System Controller
Data
B1–B8 Bus Side of Device
D1–D8 Terminal Side
of Device
I/O Ports
DS75160A
DS75161A
ATN
DAV
EOI
Attention
Data Valid
End or Identify
Interface Clear
Management IFC
Signals
NDAC Not Data Accepted
NRFD Not Ready for Data
REN Remote Enable
SRQ Service Request
DS005804-4
5
www.national.com
Logic Diagrams (Continued)
DS75161A
DS005804-5
DS005804-7
Switching Waveforms
Transmit Propagation Delays
DS005804-10
www.national.com
6
Switching Waveforms (Continued)
Receive Propagation Delays
DS005804-11
DS005804-12
DS005804-13
Terminal Enable/Disable Times
Bus Enable/Disable Times
*Input signal: f = 1.0 MHz, 50% duty cycle, t = t ≤ 5 ns
r
f
Performance Characteristics
Bus Port Load Characteristics
DS005804-14
Refer to Electrical Characteristics table
7
www.national.com
Functional Truth Tables
DS75160A
Control Input
Data Transceivers
Level
TE
H
PE
H
Direction
Bus Port Configuration
Totem-Pole Output
Open Collector Output
Input
T
T
R
H
L
L
X
DS75161A
Control Input Level
Transceiver Signal Direction
*
TE
H
H
L
DC
H
L
ATN
EOI
REN
IFC
R
SRQ
T
NRFD NDAC
DAV
T
R
T
R
T
R
T
R
T
R
R
T
T
R
R
T
T
T
R
T
H
L
R
T
R
L
T
R
R
H
L
X
H
T
R
R
T
X
H
L
L
X
X
H
L
H = High level input
L = Low level input
X = Don’t care
T = Transmit, i.e., signal outputted to bus
R = Receive, i.e., signal outputted to terminal
*
The ATN signal level is sensed for internal multiplex control of EOI transmission direction logic.
www.national.com
8
Physical Dimensions inches (millimeters) unless otherwise noted
Order Number DS75160AWM
NS Package Number M20B
9
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Molded Dual-In-Line Package (N)
Order Number DS75160AN or DS75161AN
NS Package Number N20A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: support@nsc.com
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明