DS90LV027ATMX/NOPB [TI]
600Mbps LVDS 双路高速差动驱动器 | D | 8 | -40 to 85;
| 型号： | DS90LV027ATMX/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 600Mbps LVDS 双路高速差动驱动器 | D | 8 | -40 to 85 驱动 光电二极管 接口集成电路 驱动器 |
| 文件： | 总24页 (文件大小：760K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
DS90LV027A
SNLS026D –MARCH 2000–REVISED JUNE 2016
DS90LV027A LVDS Dual High Speed Differential Driver
1 Features
3 Description
The DS90LV027A is a dual LVDS driver device
1
•
•
•
•
•
•
•
•
•
•
•
•
•
>600-Mbps (300 MHz) Switching Rates
0.3-ns Typical Differential Skew
optimized for high data rate and low-power
applications. The device is designed to support data
rates in excess of 600 Mbps (300 MHz) using Low
Voltage Differential Signaling (LVDS) technology. The
DS90LV027A is a current mode driver allowing power
dissipation to remain low even at high frequency. In
addition, the short circuit fault current is also
minimized.
0.7-ns Maximum Differential Skew
1.5-ns Maximum Propagation Delay
3.3-V Power Supply Design
±360-mV Differential Signaling
Low Power Dissipation (46 mW at 3.3-V Static)
Flow-Through Design Simplifies PCB Layout
Interoperable With Existing 5-V LVDS Devices
Power-Off Protection (Outputs in High Impedance)
Conforms to TIA/EIA-644 Standard
8-Pin SOIC Package Saves Space
The device is in a 8-pin SOIC package. The
DS90LV027A has a flow-through design for easy
printed-circuit board (PCB) layout. The differential
driver outputs provides low EMI with its typical low
output swing of 360 mV. It is perfect for high-speed
transfer of clock and data. The DS90LV027A can be
paired with its companion dual line receiver, the
DS90LV028A, or with any of TI's LVDS receivers, to
provide a high-speed point-to-point LVDS interface.
Industrial Temperature Operating Range: −40°C
to 85°C
2 Applications
Device Information(1)
•
•
•
•
Multi-Function Printers
PART NUMBER
PACKAGE
BODY SIZE (NOM)
LVCMOS-to-LVDS Translation
Building and Factory Automation
Grid Infrastructure
DS90LV027A
SOIC (8)
4.90 mm × 3.91 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
space
Functional Diagrams
DO+ 1
DI 1
D
DO- 1
Copyright © 2016, Texas Instruments Incorporated
DO+ 2
DI 2
D
DO- 2
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
DS90LV027A
SNLS026D –MARCH 2000–REVISED JUNE 2016
www.ti.com
Table of Contents
8.3 Feature Description................................................. 11
8.4 Device Functional Modes........................................ 11
Application and Implementation ........................ 12
9.1 Application Information............................................ 12
9.2 Typical Application .................................................. 12
1
2
3
4
5
6
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions ...................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics .......................................... 5
6.6 Switching Characteristics.......................................... 5
6.7 Typical Characteristics.............................................. 6
Parameter Measurement Information .................. 9
Detailed Description ............................................ 10
8.1 Overview ................................................................. 10
8.2 Functional Block Diagrams ..................................... 10
9
10 Power Supply Recommendations ..................... 13
11 Layout................................................................... 14
11.1 Layout Guidelines ................................................. 14
11.2 Layout Example .................................................... 14
12 Device and Documentation Support ................. 15
12.1 Documentation Support ........................................ 15
12.2 Receiving Notification of Documentation Updates 15
12.3 Community Resources.......................................... 15
12.4 Trademarks........................................................... 15
12.5 Electrostatic Discharge Caution............................ 15
12.6 Glossary................................................................ 15
7
8
13 Mechanical, Packaging, and Orderable
Information ........................................................... 15
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision C (April 2013) to Revision D
Page
•
Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation
section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and
Mechanical, Packaging, and Orderable Information section .................................................................................................. 1
Changes from Revision B (April 2013) to Revision C
Page
•
Changed layout of National Data Sheet to TI format ............................................................................................................. 1
2
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: DS90LV027A
DS90LV027A
www.ti.com
SNLS026D –MARCH 2000–REVISED JUNE 2016
5 Pin Configuration and Functions
D Package
8-Pin SOIC
Top View
V
1
2
3
8
D0- 1
D0+ 1
D0+ 2
D0- 2
CC
DI 1
DI 2
7
6
5
4
GND
Pin Functions
PIN
I/O
DESCRIPTION
NAME
DI
NO.
2, 3
6, 7
5, 8
4
I
TTL/CMOS driver input pins
Noninverting LVDS driver output pin
Inverting LVDS driver output pin
Ground pin
DO+
DO–
GND
VCC
O
O
—
—
1
Positive power supply pin, 3.3 V ± 0.3 V
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: DS90LV027A
DS90LV027A
SNLS026D –MARCH 2000–REVISED JUNE 2016
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
–0.3
–0.3
–0.3
MAX
4
UNIT
V
Supply voltage, VCC
Input voltage, DI
Output voltage, DO±
D package
3.6
V
3.9
V
1190
mW
Maximum package power dissipation at 25°C
Derate D package
9.5 mW/°C
above 25°C
°C
Lead temperature range, soldering (4 s)
Storage temperature, Tstg
260
150
°C
°C
–65
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
±8000
±1000
±1000
±4000
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
EIAJ, 0 Ω, 200 pF
V(ESD)
Electrostatic discharge
V
IEC direct, 330 Ω, 150 pF
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
3
NOM
3.3
MAX
3.6
UNIT
VCC
TA
Supply voltage
V
Operating free-air temperature
–40
25
85
°C
6.4 Thermal Information
DS90LV027A
D (SOIC)
8 PINS
212
THERMAL METRIC(1)
UNIT
Low-K thermal resistance(2)
High-K thermal resistance(2)
RθJA
Junction-to-ambient thermal resistance
°C/W
112
RθJC(top)
RθJB
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
69.1
°C/W
°C/W
°C/W
°C/W
°C/W
47.7
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
15.2
ψJB
47.2
RθJC(bot)
—
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
(2) Tested in accordance with the Low-K or High-K thermal metric definitions of EIA/JESD51-3 for leaded surface-mount packages.
4
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: DS90LV027A
DS90LV027A
www.ti.com
SNLS026D –MARCH 2000–REVISED JUNE 2016
6.5 Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)(1)(2)
PARAMETER
Output differential voltage
VOD magnitude change
Output high voltage
Output low voltage
Offset voltage
TEST CONDITIONS
RL = 100 Ω (see Figure 15), DO+, DO− pins
RL = 100 Ω (see Figure 15), DO+, DO− pins
RL = 100 Ω (see Figure 15), DO+, DO− pins
RL = 100 Ω (see Figure 15), DO+, DO− pins
RL = 100 Ω (see Figure 15), DO+, DO− pins
RL = 100 Ω (see Figure 15), DO+, DO− pins
VOUT = VCC or GND, VCC = 0 V, DO+, DO− pins
DO+, DO− pins
MIN TYP(3)
MAX UNIT
VOD
ΔVOD
VOH
VOL
VOS
ΔVOS
IOXD
IOSD
VIH
250
360
1
450
35
mV
mV
V
1.4
1.1
1.2
3
1.6
0.9
1.125
0
V
1.375
25
V
Offset magnitude change
Power-off leakage
Output short-circuit current
Input high voltage
mV
μA
mA
V
±1
±10
–8
–5.7
DI pin
2
VCC
0.8
VIL
Input low voltage
DI pin
GND
V
IIH
Input high current
VIN = 3.3 V or 2.4 V, DI pin
±2
±1
±10
±10
μA
μA
V
IIL
Input low current
VIN = GND or 0.5 V, DI pin
VCL
Input clamp voltage
ICL = −18 mA, DI pin
–1.5
–0.6
8
No load
VIN = VCC or GND, VCC pin
RL = 100 Ω
14
20
ICC
Power supply current
mA
14
(1) Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground
except VOD
.
(2) The DS90LV027A is a current mode device and only function with datasheet specification when a resistive load is applied to the drivers
outputs.
(3) All typicals are given for: VCC = 3.3 V and TA = 25°C.
6.6 Switching Characteristics
RL = 100 Ω and CL = 15 pF, see Figure 16 and Figure 17 (unless otherwise noted)(1)(2)(3)
PARAMETER
TEST CONDITIONS
MIN TYP(4)
MAX
1.5
1.5
0.7
0.8
1
UNIT
ns
tPHLD
tPLHD
tSKD1
tSKD2
tSKD3
tSKD4
tTLH
Differential propagation delay high to low
0.3
0.3
0
0.8
1.1
0.3
0.4
Differential propagation delay low to high
ns
(5)
Differential pulse skew |tPHLD − tPLHD
Channel to channel skew(6)
Differential part to part skew(7)
Differential part to part skew(8)
Transition low to high time
|
ns
0
ns
0
ns
0
1.2
1
ns
0.2
0.2
0.5
0.5
ns
tTHL
Transition high to low time
1
ns
fMAX
Maximum operating frequency(9)
350
MHz
(1) These parameters are ensured by design. The limits are based on statistical analysis of the device over PVT (process, voltage,
temperature) ranges.
(2) CL includes probe and fixture capacitance.
(3) Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50 Ω, tr ≤ 1 ns, tf ≤ 1 ns (10%-90%).
(4) All typicals are given for: VCC = 3.3 V and TA = 25°C.
(5) tSKD1, |tPHLD − tPLHD|, is the magnitude difference in differential propagation delay time between the positive going edge and the negative
going edge of the same channel.
(6) tSKD2 is the Differential Channel to Channel Skew of any event on the same device.
(7) tSKD3, Differential Part to Part Skew, is defined as the difference between the minimum and maximum specified differential propagation
delays. This specification applies to devices at the same VCC and within 5°C of each other within the operating temperature range.
(8) tSKD4, part to part skew, is the differential channel to channel skew of any event between devices. This specification applies to devices
over recommended operating temperature and voltage ranges, and across process distribution. tSKD4 is defined as |Max − Min|
differential propagation delay.
(9) fMAX generator input conditions: tr = tf < 1 ns (0% to 100%), 50% duty cycle, 0 V to 3 V. Output criteria: duty cycle = 45% / 55%,
VOD > 250 mV, all channels switching.
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: DS90LV027A
DS90LV027A
SNLS026D –MARCH 2000–REVISED JUNE 2016
www.ti.com
6.7 Typical Characteristics
Figure 1. Output High Voltage
vs Power Supply Voltage
Figure 2. Output Low Voltage
vs Power Supply Voltage
Figure 4. Differential Output Voltage
vs Power Supply Voltage
Figure 3. Output Short-Circuit Current
vs Power Supply Voltage
Figure 5. Differential Output Voltage
vs Load Resistor
Figure 6. Offset Voltage
vs Power Supply Voltage
6
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: DS90LV027A
DS90LV027A
www.ti.com
SNLS026D –MARCH 2000–REVISED JUNE 2016
Typical Characteristics (continued)
Figure 7. Power Supply Current
vs Power Supply Voltage
Figure 8. Power Supply Current
vs Ambient Temperature
Figure 9. Differential Propagation Delay
vs Power Supply Voltage
Figure 10. Differential Propagation Delay
vs Ambient Temperature
Figure 11. Differential Skew
vs Power Supply Voltage
Figure 12. Differential Skew
vs Ambient Temperature
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: DS90LV027A
DS90LV027A
SNLS026D –MARCH 2000–REVISED JUNE 2016
www.ti.com
Typical Characteristics (continued)
Figure 13. Transition Time
vs Power Supply Voltage
Figure 14. Transition Time
vs Ambient Temperature
8
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: DS90LV027A
DS90LV027A
www.ti.com
SNLS026D –MARCH 2000–REVISED JUNE 2016
7 Parameter Measurement Information
DO+
RL / 2
2 V
DI
VOD
D
VOS
0.8 V
SI
RL / 2
DO-
Copyright © 2016, Texas Instruments Incorporated
Figure 15. Differential Driver DC Test Circuit
DI
DO+
DO-
Generator
D
CL
RL
50 Ω
Copyright © 2016, Texas Instruments Incorporated
Figure 16. Differential Driver Propagation Delay and Transition Time Test Circuit
3 V
DI
1.5 V
tPLH
1.5 V
tPHLD
0 V
DO-
VOH
VOL
0 V (Differential)
0 V
DO+
80 %
0 V
80 %
VDIFF
0 V
VDIFF = (DO+) œ (DO-)
20 %
20 %
tTHL
tTHL
Figure 17. Differential Driver Propagation Delay and Transition Time Waveforms
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: DS90LV027A
DS90LV027A
SNLS026D –MARCH 2000–REVISED JUNE 2016
www.ti.com
8 Detailed Description
8.1 Overview
LVDS drivers and receivers are intended to be primarily used in an uncomplicated point-to-point configuration as
is shown in Figure 19. This configuration provides a clean signaling environment for the fast edge rates of the
drivers. The receiver is connected to the driver through a balanced media which may be a standard twisted pair
cable, a parallel pair cable, or simply PCB traces. Typically, the characteristic differential impedance of the media
is in the range of 100 Ω. A termination resistor of 100 Ω (selected to match the media), and is placed as close to
the receiver input pins as possible. The termination resistor converts the driver output current (current mode) into
a voltage that is detected by the receiver. Other configurations are possible such as a multi-receiver
configuration, but the effects of a mid-stream connector(s), cable stub(s), and other impedance discontinuities as
well as ground shifting, noise margin limits, and total termination loading must be considered. The DS90LV027A
differential line driver is a balanced current source design. A current mode driver, generally speaking has a high
output impedance and supplies a constant current for a range of loads (a voltage mode driver on the other hand
supplies a constant voltage for a range of loads). Current is switched through the load in one direction to produce
a logic state and in the other direction to produce the other logic state. The output current is typically 3.1 mA, a
minimum of 2.5 mA, and a maximum of 4.5 mA. The current mode driver requires (as discussed above) that a
resistive termination be employed to terminate the signal and to complete the loop as shown in Figure 19. AC or
unterminated configurations are not allowed. The 3.1-mA loop current develops a differential voltage of 310 mV
across the 100-Ω termination resistor which the receiver detects with a 250-mV minimum differential noise
margin, (driven signal minus receiver threshold (250 mV – 100 mV = 150 mV). The signal is centered around 1.2
V (Driver Offset, VOS) with respect to ground as shown in Figure 18.
NOTE
The steady-state voltage (VSS) peak-to-peak swing is twice the differential voltage (VOD)
and is typically 620 mV.
The current mode driver provides substantial benefits over voltage mode drivers, such as an RS-422 driver. Its
quiescent current remains relatively flat versus switching frequency. Whereas the RS-422 voltage mode driver
increases exponentially in most case from 20 MHz to 50 MHz. This is due to the overlap current that flows
between the rails of the device when the internal gates switch. Whereas the current mode driver switches a fixed
current between its output without any substantial overlap current. This is similar to some ECL and PECL
devices, but without the heavy static ICC requirements of the ECL/PECL designs. LVDS requires >80% less
current than similar PECL devices. AC specifications for the driver are a tenfold improvement over other existing
RS-422 drivers.
8.2 Functional Block Diagrams
DO+ 1
DI 1
D
DO- 1
Copyright © 2016, Texas Instruments Incorporated
DO+ 2
DI 2
D
DO- 2
Copyright © 2016, Texas Instruments Incorporated
10
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: DS90LV027A
DS90LV027A
www.ti.com
SNLS026D –MARCH 2000–REVISED JUNE 2016
8.3 Feature Description
8.3.1 LVDS Fail-Safe
This section addresses the common concerns of fail-safe biasing of LVDS interconnects, specifically looking at
the DS90LV027A driver outputs and the DS90LV028A receiver inputs.
The LVDS receiver is a high-gain, high-speed device that amplifies a small differential signal (20 mV) to CMOS
logic levels. Due to the high gain and tight threshold of the receiver, take care to prevent noise from appearing as
a valid signal.
The internal fail-safe circuitry of the receiver is designed to source or sink a small amount of current, providing
fail-safe protection (a stable known state of HIGH output voltage) for floating, terminated, or shorted receiver
inputs.
1. Open Input Pins: The DS90LV028A is a dual receiver device, and if an application requires only 1 receiver,
the unused channel inputs must be left OPEN. Do not tie unused receiver inputs to ground or any other
voltages. The input is biased by internal high value pullup and pulldown resistors to set the output to a HIGH
state. This internal circuitry ensures a HIGH, stable output state for open inputs.
2. Terminated Input: If the DS90LV027A driver is disconnected (cable unplugged), or if the DS90LV027A driver
is in a TRI-STATE or power-off condition, the receiver output is in a HIGH state again, even with the end of
cable 100-Ω termination resistor across the input pins. The unplugged cable can become a floating antenna
which can pick up noise. If the cable picks up more than 10 mV of differential noise, the receiver may see the
noise as a valid signal and switch. To insure that any noise is seen as common-mode and not differential, a
balanced interconnect must be used. Twisted pair cable offers better balance than flat ribbon cable.
3. Shorted Inputs: If a fault condition occurs that shorts the receiver inputs together, thus resulting in a 0-V
differential input voltage, the receiver output remains in a HIGH state. Shorted input fail-safe is not supported
across the common-mode range of the device (GND to 2.4 V). It is only supported with inputs shorted and no
external common-mode voltage applied.
External lower value pullup and pulldown resistors (for a stronger bias) may be used to boost fail-safe in the
presence of higher noise levels. The pullup and pulldown resistors must be in the 5-kΩ to 15-kΩ range to
minimize loading and waveform distortion to the driver. The common-mode bias point must be set to
approximately 1.2 V (less than 1.75 V) to be compatible with the internal circuitry.
3V
DIN
0V
V0H
DOUT-
V0D
V0S (1.2V typical)
V0L
SINGLE-ENDED
DOUT+
+V0D
-V0D
DOUT+ œ DOUT-
VSS
0V
0V (DIFF.)
DIFFERENTIAL OUTPUT
Figure 18. Driver Output Levels
8.4 Device Functional Modes
Table 1 lists the functional modes of the DS90LV027A.
Table 1. Truth Table
INPUT
OUTPUTS
DI
L
DO+
L
DO–
H
H
H
L
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: DS90LV027A
DS90LV027A
SNLS026D –MARCH 2000–REVISED JUNE 2016
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The DS90LV027A has a flow-through pinout that allows for easy PCB layout. The LVDS signals on one side of
the device easily allows for matching electrical lengths of the differential pair trace lines between the driver and
the receiver as well as allowing the trace lines to be close together to couple noise as common-mode. Noise
isolation is achieved with the LVDS signals on one side of the device and the TTL signals on the other side.
General application guidelines and hints for LVDS drivers and receivers may be found in the following application
notes:
•
•
•
•
•
•
•
LVDS Owner's Manual
AN-808 Long Transmission Lines and Data Signal Quality
AN-977 LVDS Signal Quality: Jitter Measurements Using Eye Patterns Test Report
AN-971 An Overview of LVDS Technology
AN-916 A Practical Guide To Cable Selection
AN-805 Calculating Power Dissipation for Differential Line Drivers
AN-903 A Comparison of Differential Termination Techniques
9.2 Typical Application
Any LVDS
Receiver
+
-
DATA
INPUT
DATA
OUTPUT
RT
100W
Copyright © 2016, Texas Instruments Incorporated
Figure 19. LVDS Application Schematic
9.2.1 Design Requirements
When using LVDS devices, it is important to remember to specify controlled impedance PCB traces, cable
assemblies, and connectors. All components of the transmission media must have a matched differential
impedance of about 100 Ω. They must not introduce major impedance discontinuities. Balanced cables (for
example, twisted pair) are usually better than unbalanced cables (ribbon cable) for noise reduction and signal
quality.
Balanced cables tend to generate less EMI due to field canceling effects and also tend to pick up
electromagnetic radiation as common-mode (not differential mode) noise which is rejected by the LVDS receiver.
For cable distances < 0.5 M, most cables can be made to work effectively. For distances 0.5 M ≤ d ≤ 10 M,
CAT5 (Category 5) twisted pair cable works well, is readily available, and relatively inexpensive.
12
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: DS90LV027A
DS90LV027A
www.ti.com
SNLS026D –MARCH 2000–REVISED JUNE 2016
Typical Application (continued)
9.2.2 Detailed Design Procedure
9.2.2.1 Probing LVDS Transmission Lines
Always use high impedance (>100 kΩ), low capacitance (<2 pF) scope probes with a wide bandwidth (1 GHz)
scope. Improper probing gives deceiving results.
A pseudo-random bit sequence (PRBS) of 29−1 bits was programmed into a function generator (Tektronix
HFS9009) and connected to the driver inputs through 50-Ω cables and SMB connectors. An oscilloscope
(Tektronix 11801B) was used to probe the resulting eye pattern, measured differentially at the input to the
receiver. A 100-Ω resistor was used to terminate the pair at the far end of the cable. The measurements were
taken at the far end of the cable, at the input of the receiver, and used for the jitter analysis for Figure 21. The
frequency of the input signal was increased until the measured jitter (ttcs) equaled 20% with respect to the unit
interval (ttui) for the particular cable length under test. Twenty percent jitter is a reasonable place to start with
many system designs. The data used was NRZ. Jitter was measured at the 0-V differential voltage of the
differential eye pattern.
The DS90LV027A and DS90LV028A can be evaluated using the new DS90LV047-048AEVM.
9.2.3 Application Curves
Figure 20. Power Supply Current
vs Frequency
Figure 21. Data Rate
vs Cable Length
10 Power Supply Recommendations
Although the DS90LV027A draws very little power while at rest, at higher switching frequencies there is a
dynamic current component which increases the overall power consumption. The DS90LV027A power supply
connection must take this additional current consumption into consideration for maximum power requirements.
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: DS90LV027A
DS90LV027A
SNLS026D –MARCH 2000–REVISED JUNE 2016
www.ti.com
11 Layout
11.1 Layout Guidelines
•
•
Use at least 4 PCB layers (top to bottom); LVDS signals, ground, power, and TTL signals.
Isolate TTL signals from LVDS signals, otherwise the TTL may couple onto the LVDS lines. Best practice is to
place TTL and LVDS signals on different layers which are isolated by power or ground plane(s).
•
Keep drivers and receivers as close to the (LVDS port side) connectors as possible.
11.2 Layout Example
DS90LV028A
DS90LV027A
1
2
3
4
VCC
16
15
14
13
1
2
3
4
8
7
6
5
RIN1-
RIN1+
RIN2+
RIN2-
DO- 1
DO+ 1
DO+ 2
DO- 2
VCC
DI 1
DI 2
Series Termination (optional)
ROUT1
ROUT2
GND
LVCMOS
Inputs
LVCMOS
Outputs
Decoupling Cap
(Bottom Layer)
GND
Decoupling Cap
(Bottom Layer)
Input Termination
(Required)
Figure 22. Simplified DS90LV027A and DS90LV028A Layout
14
Submit Documentation Feedback
Copyright © 2000–2016, Texas Instruments Incorporated
Product Folder Links: DS90LV027A
DS90LV027A
www.ti.com
SNLS026D –MARCH 2000–REVISED JUNE 2016
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation see the following:
•
•
•
•
•
•
•
LVDS Owner's Manual
AN-808 Long Transmission Lines and Data Signal Quality
AN-977 LVDS Signal Quality: Jitter Measurements Using Eye Patterns Test Report
AN-971 An Overview of LVDS Technology
AN-916 A Practical Guide To Cable Selection
AN-805 Calculating Power Dissipation for Differential Line Drivers
AN-903 A Comparison of Differential Termination Techniques
12.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2000–2016, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: DS90LV027A
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
DS90LV027ATM
NRND
SOIC
SOIC
SOIC
D
D
D
8
8
8
95
Non-RoHS
& Green
Call TI
Level-1-235C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
-40 to 85
LV27A
TM
DS90LV027ATM/NOPB
DS90LV027ATMX/NOPB
ACTIVE
ACTIVE
95
RoHS & Green
SN
SN
LV27A
TM
2500 RoHS & Green
LV27A
TM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
30-Sep-2021
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
DS90LV027ATMX/NOPB SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SOIC
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 35.0
DS90LV027ATMX/NOPB
D
8
2500
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TUBE
T - Tube
height
L - Tube length
W - Tube
width
B - Alignment groove width
*All dimensions are nominal
Device
Package Name Package Type
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
DS90LV027ATM
DS90LV027ATM
D
D
D
SOIC
SOIC
SOIC
8
8
8
95
95
95
495
495
495
8
8
8
4064
4064
4064
3.05
3.05
3.05
DS90LV027ATM/NOPB
Pack Materials-Page 3
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明