EMB1428QSQX/NOPB [TI]
用于主动电池均衡的开关矩阵栅极驱动器 | RHS | 48;型号: | EMB1428QSQX/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 用于主动电池均衡的开关矩阵栅极驱动器 | RHS | 48 电池 开关 栅极驱动 驱动器 |
文件: | 总29页 (文件大小:426K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
EMB1428Q Switch Matrix Gate Driver
Check for Samples: EMB1428Q
1
FEATURES
DESCRIPTION
The EMB1428 Switch Matrix Gate Driver IC is
designed to work in conjunction with EMB1499
DC/DC Controller IC to support TI’s switch matrix
based active cell balancing scheme in a battery
management system. The EMB1428 provides 12
floating MOSFET gate drivers necessary for
balancing up to 7 battery cells connected in a series
stack. Multiple EMB1428 ICs may be used together
to balance a stack of more than seven battery cells.
2
•
•
•
60V Maximum Stack Operating Voltage
Twelve (12) Floating Gate Drivers
SPI Bus Interface (for Charge/discharge
Commands and Fault Reporting)
•
•
Low Power Sleep Mode
EMB1428Q is an Automotive Grade Product
that is AEC-Q100 Grade 1 Qualified (-40°C to
+125°C Operating Junction Temperature)
The EMB1428 integrated circuit interfaces with the
EMB1499 DC/DC controller to control and enable
charging and discharging modes. The EMB1428 uses
an SPI bus to accept commands from the main
controller (CPU/MCU) on which battery cell should be
charged or discharged and to report back any faults
to the main controller (CPU/MCU).
APPLICATIONS
•
•
•
Li-Ion Battery Management Systems
Electrical/Hybrid Vehicles
Grid-Power Storage
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012–2013, Texas Instruments Incorporated
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
Typical Application
Vstack
Vstack
°
EMB1499
7-Cell
Half-
Stack
GATE_LS
GATE_HS2
®
GATE_HS1
VSENSE_HS
VSENSE_LS
MOSFET
DRIVER
PWM_CLAMP
CELLPLUS
+12V
VINA
VINP
VINF
PVINF
Floating
12V Supply
PGNDF
GNDF
°
¯
VSET
DAC
EMB1428
EN
DIR
EN
DIR
DIR_RT
DONE
SOURCE[11..0]
GATE[11..0]
DIR_RT
DONE
FAULT2
FAULT1
FAULT0
FAULT2
FAULT1
FAULT0
VDDCP
CEXT2
GNDA GNDP
CEXT1
CPU OR
MCU
SPI BUS
CS
SD0
VSTACK
SDI
+12V
VDD12V
VDDP
SCLK
VDD5V
VDDIO
+5V
+3.3V
TO OTHER BALANCING CIRCUIT
FAULT_INT
RST
GNDP GND
Figure 1. Typical Application
2
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
Connection Diagram
1
2
3
4
5
6
7
36
35
34
33
32
31
30
GND
GNDP
VDDP
RST
VDD12V
VDD5V
VDDIO
FAULT_INT
CS
SOURCE7
GATE7
SOURCE6
GATE6
EMB1428
(Top View)
SOURCE5
8
9
29
28
GATE5
SDO
SDI
SOURCE4
10
11
12
27
26
25
GATE4
SOURCE3
GATE3
SCLK
EN
* Exposed pad must be soldered to ground
Plane to ensure rated performance
DIR
48-Pin WQFN
See RHS Package
Table 1. ORDERING INFORMATION
Order number
Package
Type
Package
Drawing
Supplied As
Features
EMB1428QSQ
EMB1428QSQE
EMB1428QSQX
1000 Units in Tape and Reel
250 Units in Tape and Reel
2500 Units in Tape and Reel
AECQ100 Grade qualified. Automotive
EMB1428QSQE 250 Units in Tape and
Reel Grade Production Flow(1)
WQFN
RHS
(1) Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect
detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC-Q100
standard. Automotive grade products are identified with the letter Q. For more information go to http://www.ti.com/automotive.
PIN DESCRIPTIONS
Pin
1
Name
GNDP
VDDP
Description
Application Information
Ground for charge pump circuitry
12V supply for charge pump circuitry
Connect to stack ground at board level.
2
Connect to 12V supply at board level with
0.1µF bypass cap to GNDP.
3, 5, 7, 9, 11, 14,
16, 18, 37, 39, 41,
43
SOURCE0 to
SOURCE11
Floating driver references
Floating driver outputs
Ground
Connect to FET switch sources.
4, 6, 8, 10, 12, 15,
17, 19, 38, 40, 42,
44
GATE0 to GATE11
Connect to FET switch gates.
13, 36
GND
Internal reference for all analog and digital
circuitry except the charge pump.
20, 21, 22
FAULT[2, 1, 0]
Inputs, three-bit digital fault code from
EMB1499
Fault code is reported to CPU through the
SPI bus. 5V Schmitt-trigger inputs, 12V
signal tolerant.
23
DONE
Input from EMB1499, indicates end of charge 5V Schmitt-trigger input, 12V signal tolerant.
cycle
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
PIN DESCRIPTIONS (continued)
Pin
Name
Description
Application Information
24
DIR_RT
Input from EMB1499, handshake signal,
inverted version of DIR
5V Schmitt-trigger input, 12V signal tolerant.
25
26
DIR
EN
Output to EMB1499, indicates direction of
charging current
'High' indicates charge mode, 'Low' indicates
discharge mode. 5V CMOS output levels.
Output to EMB1499, enable signal for
charge/discharge cycle
'High' signals EMB1499 to begin charge or
discharge cycle, 'Low' signals EMB1499 to
ramp down current and finish present cycle.
5V CMOS levels.
27
SCLK
SPI clock input
1MHz SPI interface, I/O levels are
referenced to the VDDIO supply.
28
29
30
31
32
33
SDI
SDO
SPI data input
SPI data output
CS
SPI chip select input
FAULT_INT
VDDIO
VDD5V
Fault interrupt output to CPU
IO supply for SPI interface circuitry
Referenced to the VDDIO supply.
Connect to CPU supply to match I/O levels.
5V supply for digital core and EMB1499
interface circuitry
34
35
45
VDD12V
RST
12V supply for analog core circuitry
RESET pin
VDDCP
Floating supply input from external charge
pump circuit
Connected to external charge pump circuit
that provides a floating supply referenced to
the top of the battery module (VSTACK).
46, 47
48
CEXT1, CEXT2
VSTACK
Charge pump driver outputs
Buffered, differential 1MHz clock signals for
driving external charge pump circuit.
Supply from the highest voltage in the battery
module
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
4
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
ABSOLUTE MAXIMUM RATINGS(1)
Any SOURCE pin to GND
VSTACK to GND
-0.5V to 70V
-0.5V to 70V
-0.5V to 25V
-0.5V to 90V
-0.5V to 16V
-0.5V to 16V
-0.5V to 0.5V
-0.5V to 16V
-0.5V to 7.5V
-0.5V to 7.5V
±2 kV
VDDCP to VSTACK
VDDCP to GND
VDD12V to GND
VDDP to GNDP
GNDP to GND
FAULTx, DONE, DIR_RT to GND
VDD5V, VDDIO to GND
All other inputs to GND
ESD Rating(2)
Soldering Information
Junction Temperature
Storage Temperature
150°C
-65°C to 150°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the recommended Operating Ratings is not implied. The recommended Operating Ratings
indicate conditions at which the device is functional and should not be operated beyond such conditions.
(2) The human body model is a 100pF capacitor discharged through a 1.5 kΩ resistor into each pin. Test method is per JESD22–A114.
OPERATING RATINGS
VSTACK to GND
VDD12V to GND
VDDP to GNDP
15V to 60V
10.8V to 13.2V
10.8V to 13.2V
4.5V to 5.5V
2.5V to 5.5V
18V to 24V
VDD5V, to GND
VDDIO to GND
VDDCP to VSTACK
Junction Temperature (TJ)
-40°C to 125°C
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
ELECTRICAL CHARACTERISTICS
Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of −40°C
to +125°C. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at TJ = 25°, and are provided for reference purposes only. VSTACK = 60V, SOURCEX = 0V,
VDD12V = VDDP = 12V, VDD5V = 5V, VDDIO = 3.3V unless otherwise indicated in the conditions column.
Symbol
Parameter
Conditions
Min
Typ(1)
Max
Units
System Parameters
ISTACK
Stack supply current
System connected to Cell 1,
EN high
1.57
4
2.4
6
mA
mA
IVDDP
Charge pump driver supply
current
IVDD12V
IVDD5V
12V supply current
VSTACK = 60V
100
135
0.2
125
180
1.8
2.3
0.4
µA
µA
µA
µA
µA
5V supply current
SOURCEx = 60V
IVDDIO
IO supply current
ISTACK_SD
IVDDP_SD
Stack supply current, shutdown
Shutdown (FETs disconnected)
VSTACK = 60V
1.4
Charge pump driver supply
current, shutdown
IVDD12V_SD
IVDD5V_SD
IVDDIO_SD
ISTACK_RST
IVDDP_RST
12V supply current, shutdown
5V supply current, shutdown
IO supply current, shutdown
Stack supply current, reset
SOURCEx = 60V
0.2
11
µA
µA
µA
µA
µA
8.7
0.1
2.3
0.8
RESET
0.28
Charge pump driver supply
current, reset
VSTACK = 60V
IVDD12V_RST
IVDD5V_RST
IVDDIO_RST
12V supply current, reset
5V supply current, reset
IO supply current, reset
SOURCEx = 60V
1.2
28
µA
µA
µA
20
0.5
FET Driver Parameters
tEN
Driver setup time, Cell-to-Cell
Rising edge of DONE to rising edge
of EN
2.4
2.4
500
14
ms
ms
Driver set up time from shutdown Rising edge of CS to rising edge of
EN
1.23
330
12.1
3.5
tPD
Shutdown time
Rising edge of DONE to last clock
pulse on CEXT2
µs
VGSON
ΔVGSON
Driver output 'on' voltage, VGATE
VSOURCE
-
10.8
100
V
VSTACK Line Regulation
VSOURCE Line Regulation
SOURCEx = 0V, VSTACK = 15V to
60V
9
mV/V
mV/V
µA
SOURCEx = 0V to 60V, VSTACK =
60V
5.5
20
IGON
GATE pin output drive current
during FET turn-on transient
(GATE-SOURCE) = VGSON/2
225
16.2
RGSTRANS
Driver output pull-down
(GATE-SOURCE) = VGSON/2
17.5
Ω
resistance during FET turn-off
transient, GATE to SOURCE pin
RGSON
Driver output pull-down
resistance active
100
100
150
150
220
220
Ω
Ω
RGSOFF
Driver output pull-down
resistance after FET turn-off
transient has finished, GATE to
SOURCE pin
(GATE-SOURCE) ≤ 0.2V
ISRC
SOURCE pin bias current, power-
up, driver output on
210
80
µA
µA
nA
SOURCE pin bias current, power-
up, driver output off
ISRC_SD
SOURCE pin bias current, power- Shutdown
down
100
(1) Typical specifications represent the most likely parametric norm at 25°C operation.
Submit Documentation Feedback
6
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
ELECTRICAL CHARACTERISTICS (continued)
Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of −40°C
to +125°C. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at TJ = 25°, and are provided for reference purposes only. VSTACK = 60V, SOURCEX = 0V,
VDD12V = VDDP = 12V, VDD5V = 5V, VDDIO = 3.3V unless otherwise indicated in the conditions column.
Symbol
Parameter
Conditions
Min
Typ(1)
Max
Units
Charge Pump Parameters
VCPO
Charge pump output measured
with respect to VSTACK
VDDP = 12V, System connected to
Cell 1, EN high
23.5
V
ROUT_CP
VCP_UVH
Charge pump output resistance
1.7
16
Ω
Charge pump UVLO upper trip
voltage, VDDCP - VSTACK
V
VCP_UVL
fCLK
Charge pump UVLO lower trip
voltage, VDDCP - VSTACK
14
V
CEXT1,2 pin clock frequency
0.9
1.0
1.15
2.35
MHz
SPI/Microcontroller Interface Input Parameters (CS, SDI, SCLK, RST)
VIH
CS, SDI, SCLK Logic high
threshold
2.25
1.0
V
V
VIL
CS, SDI, SCLK Logic low
threshold
0.95
1.45
VIH-5V
VIL-5V
IIN
CS, SDI, SCLK Logic high
threshold
VDDIO = 5.0V
3.47
1.55
3.6
V
CS, SDI, SCLK Logic low
threshold
V
SDI, SCLK Input bias current
VSDI, VSCLK = VDDIO = 5.0V
0.01
0.1
µA
kΩ
RPUCS
Internal Pull-up resistance from
CS to VDDIO
98
VIH_RST
VIL_RST
RPDRST
Reset Logic high threshold
Reset Logic low threshold
1.0
0.95
98
1.35
V
V
0.55
3.15
Internal Pull-down resistance
from RST to GND
kΩ
SPI/Microcontroller Interface Output Parameters (FAULT_INT, SDO)
VOH
Output High Voltage
ISOURCE = 200µA
ISOURCE = 1mA
ISINK = 200µA
3.19
2.7
V
V
VOL
Output Low Voltage
0.12
0.6
0.155
V
ISINK = 1mA
V
IOZH
IOZL
SDO TRI-STATE Leakage
current (high)
VSDO = 0V or VDDIO
3
µA
SDO TRI-STATE Leakage
current (low)
VSDO = 0V or VDDIO
0.2
µA
SPI/Microcontroller Interface Timing Specifications (Need SPI mode)
fSCLK
DC
Serial clock from CPU
SCLK Duty Cycle
1.0
50
1.1
MHz
%
10
75
tCSU
CS falling edge to SCLK rising
edge
100
ns
tCDSU
CS rising edge to SCLK rising
edge
50
ns
tTRANS
tSU
CS high pulse width
1.5
50
µs
ns
ns
SDI setup to SCLK rising edge
SDO setup from SCLK rising
edge
200
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of −40°C
to +125°C. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at TJ = 25°, and are provided for reference purposes only. VSTACK = 60V, SOURCEX = 0V,
VDD12V = VDDP = 12V, VDD5V = 5V, VDDIO = 3.3V unless otherwise indicated in the conditions column.
Symbol
Parameter
Conditions
Min
200
Typ(1)
Max
Units
tHD
CSand SDI hold time from SCLK
rising edge
ns
SDO hold time from SCLK rising
edge
250
ns
tCS
CS falling edge to SDO enabled
50
60
ns
ns
tDIS
CS rising edge to SDO disabled
(tri-state)
EMB1499 Interface Input Parameters (FAULT0, FAULT1, FAULT2, DIR_RT, DONE)
VIH-EMB1499
VIL-EMB1499
IIN-EMB1499
Logic high threshold
Logic low threshold
Input bias current
3.4
1.6
3.6
V
V
1.4
V(FAULTX, DIR_RT, DONE) = 12V
0.6
µA
1
EMB1499 Interface Output Parameters (EN, DIR)
VOH-EMB1499
Output High Voltage
ISOURCE = 200µA
ISOURCE = 1mA
ISINK = 200µA
ISINK = 1mA
4.86
4.9
4.4
V
V
V
V
VOL-EMB1499
Output Low Voltage
0.11
0.56
0.3
EMB1499 Interface Timing Specifications
tDIR
DIR transition to corresponding
700
ns
DIR_RT
tDIRSU
tINT
DIR setup to EN rising edge
3.4
µs
µs
Any fault condition to FAULT_INT
rising edge
2
tDNL
tFSU
DONE low pulse width
Prior to EMB1499 fault condition
3
1
µs
µs
FAULT[2, 1, 0] setup to DONE
rising edge
EMB1499 reporting a fault condition
tFHD
FAULT[2, 1, 0] hold time from
DONE rising edge
8
µs
8
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
BLOCK DIAGRAM
EXTERNAL CIRCUITRY
FROM TOP OF BATTERY
STACK (60V MAX)
0.01P
0.01P
0.01P
VDDCP
CEXT1
CEXT2
CHARGE PUMP
VSTACK
Approx. VSTACK + (2 X VDDP)
HV CURRENT MIRROR
SOFT
START
VDDP
GNDP
CHARGE
PUMP
UVLO
CLK
LEVEL SHIFT
FLOATING DRIVER 12X
SHUTDOWN BIAS
100 nA
DRIVER BIAS CURRENT
GENERATOR
VDD5V
RST
1 MHz
CLOCK
VDD12V
POR
DRVR
UVLO
LEVEL
SHIFT
DRIVER
GATE
SOURCE
VDDIO
BANDGAP
5V CORE LOGIC
CS
CLK
SDI
SDO
SPI
INTER-
FACE
bg_good
3.3V
I/O
FAULT_INT
VDD5V
STATE
DIR_RT
DONE
FAULT[2..0]
MACHINE
EMB1499
INTER-
FACE
5V
I/O
bg_good
DIR
EN
SWITCH _EN
SLEW
Figure 2. EMB1428 High -Level Block Diagram
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
APPLICATION INFORMATION
The EMB1428 and the EMB1499 work in conjunction to control an active balancing circuit for up to 7 battery cells
connected in series. See Typical Application for the typical system architecture. The EMB1428 provides 12
floating gate drivers that are needed for the control of the FET switch matrix in the circuit. The EMB1499 is a
DC/DC controller that regulates the inductor current in the bi-directional forward converter. In a typical
application, the forward converter has the inductor side connected to the switch matrix and the other side to the
battery stack. With such an arrangement, every cell balancing action is an energy exchange between a cell and
the whole stack. The maximum number of cells in such a stack is constrained by the maximum stack voltage the
EMB1428 can handle (60V). Theoretically the 7 cells associated with an EMB1428 can be anywhere along the
stack. So in the case of a 14-cell stack, one EMB1428 can be used to handle the lower 7 cells (lower half-stack),
and another EMB1428 can be used to handle the upper 7 cells (upper half-stack).
When the EMB1428 receives a cell balance command from the micro controller to charge or discharge a
particular cell, it will first turn off all switches irrelevant to the balancing of that cell and then turn on the switches
that will properly connect the cell to the forward converter. Once the proper switches in the switch matrix have
been turned on, the EMB1428 will signal the EMB1499 to start charging or discharging the cell. The EMB1499
will then ramp the forward converter’s inductor current (positive or negative) to a user-defined magnitude and
keep a current constant. The inductor current is the balancing current the cell receives. Upon receiving a
command from the microcontroller to stop balancing or to switch balancing action to a different cell, the
EMB1428 will inform the EMB1499 to bring the balancing current towards zero. Once the inductor current has
ramped down to zero, the EMB1428 will turn off all the switches that are not needed by the new command and
turn on the switches that are needed (if any). If the new command is to balance a different cell, the EMB1428 will
then signal the EMB1499 to ramp the inductor current again. If the new command is to stop balancing, the
EMB1428 will enter a low power sleep mode, also known as shutdown mode.
The Switch Matrix
The FET switches in a switch matrix fall into two categories. See Figure 3 for a detailed illustration. The switches
directly connected to the battery cells are called the “cell switches”. Each cell switch is comprised of two N-FETs
that are connected in a common source and common gate manner and is capable of blocking current flow in
both directions. The switches directly connected to the DC/DC converter are called the "polarity switches". Each
polarity switch is simply an N-FET and is capable of blocking current flow in one direction only.
Of the 7 cells handled by the EMB1428, assume the bottom cell is Cell 1, the one above it is Cell 2, and so on.
Cell 1 is connected to two cell switches, i.e. Cell Switch 0 and Cell Switch 1 (CSW0 and CSW1). Cell 2 is
connected to CSW1 and CSW2. This pattern repeats through all cell connections. Each cell switch has one drain
node connected to either the EVEN rail (if the switch is even numbered) or the ODD rail (if the switch is odd
numbered). Each of the four polarity switches (PSW0 through PSW3) either has a drain connected to the positive
end of the DC/DC converter and a source connected to the EVEN or ODD rail, or has a source connected to the
negative end of the DC/DC converter and a drain to the EVEN or ODD rail. The function of the cell switches is to
select the chosen cell on the EVEN and ODD rails and the function of the polarity switches is to connect the cell
to the DC/DC converter in a positive-to-positive and negative-to-negative manner.
Each time the EMB1428 tries to charge or discharge a certain cell, it will first turn off all irrelevant switches, and
turn on or keep on relevant cell switches. It will then connect the cell to the EVEN and ODD rails and turn on the
appropriate polarity switches.
10
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
VSTACK
TOP OF STACK
GATE7
GATE11
PSW3
CSW7
CSW6
CSW5
CSW4
CSW3
CSW6
CSW1
CSW0
ODD
SOURCE11
SOURCE 7
GATE6
CELL 7
CELL 6
CELL 5
CELL 4
CELL 3
CELL 2
CELL 1
GATE10
PSW2
SOURCE10
DC/DC
EVEN
SOURCE6
GATE5
CONVERTER
GATE9
PSW1
SOURCE9
SOURCE5
GATE4
GATE8
PSW0
SOURCE8
SOURCE4
GATE3
SOURCE3
GATE6
POLARITY SWITCHES
SOURCE2
GATE1
SOURCE1
GATE0
CELL SWITCHES
SOURCE0
BOTTOM OF STACK
Figure 3. Switch Matrix
Reference Current Generator
A block diagram of the reference current generator is shown in Figure 4. This block generates bias currents that
are used in the 12 floating drivers to create temperature-stable driver output voltages. The main blocks in the
reference current generator are bandgap, opamp, resistor/diode stack, and shutdown bias generator.
The 5V bandgap voltage is forced across a stack of resistors and diodes in the operational amplifier feedback
loop to generate a reference current. The reference current is mirrored from the VDDCP rail to each of the 12
floating drivers.
During sleep mode the bandgap output is held at 0V such that the reference current output is zero. A SOURCE
shutdown bias current, ISRC, is already created by a parallel bias generator that is active any time VSTACK is
greater than 2V typical. The SOURCE shutdown bias current ensures that the driver outputs will be clamped off
during shutdown if there is any significant voltage applied to VSTACK.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
Approx. VSTACK + (2 X VDDP)
HV CURRENT MIRROR
VDDCP
BIAS CURRENTS
TO DRIVERS
Cpgood (From Charge Pump)
SHUTDOWN BIAS
100 nA
VDD12V
BANDGAP
bg_good
Figure 4. Reference Current Generator
The reference generator also monitors the cpgood signal which comes from the charge pump UVLO. If cpgood is
low then the reference generator is held in a standby mode with zero output current until the charge pump has
started. This delay prevents supply headroom issues that can occur if the drivers are turned on before the charge
pump has created a large enough voltage at the VDDCP pin.
The bg_good signal is generated by a Schmitt trigger inverter that is driven by the operational amplifier feedback
loop. This signal indicates that the bandgap has started up, the charge pump is operational, and the reference
current is flowing to the drivers. The digital block monitors the bg_good signal and generates a fault if it is low
when an SPI command is received.
Floating Gate Driver
Figure 5 shows the main blocks in the floating gate driver cell along with a dual-FET load and the built-in bleeder
resistor. Each of the 12 drivers has a floating supply generator, shutdown circuit, UVLO, level-shift, and output
buffer. The SOURCE pin can be up to 60V above ground for a 14 cell pack (14X4.3V) and the GATE pin must be
able to swing 12V above the SOURCE pin (in some cases above the top of the battery stack) to turn on the
external FETs.
The internal 100k bleeder resistors ensure that the FET switches will automatically turn off in the event of a
catastrophic driver failure and that the FET switches are in an off state upon system power-up. The driver is
designed to drive the FET switch directly with no gate-source resistor.
12
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
VDDCP
Reference Current
From IrefGen
Floating
Supply
Generator
External
to
EMB1428
OUTPUT
DRIVER
Level
Shift
Shutdown
UVLO
100 k:
Bleeder
Resistor
SOURCE
Pin
Dual-FET
Switch
bg_good
SWITCH_EN
slew
Level
Shift
SWITCH_EN
Figure 5. Floating Gate Driver
Each driver receives a reference current from the VDDCP rail that must flow out of the SOURCE pin and into the
FET network along with the rest of the driver's bias current. The total SOURCE pin current for each driver with an
off output is ISRC. For drivers with outputs that are 'on', IGON flows through the bleeder resistor and out of the
source connection. For drivers 0 through 7 this current can flow into the battery stack or into the EVEN or ODD
rail depending on which of the two FET body diodes is forward biased. This current helps ensure that the source
connection of the dual-FET switches does not get pulled down such that a drain-source breakdown occurs. For
drivers 8 through 11 this current usually flows into the EVEN or ODD rails, through an 'ON' dual-FET switch, and
back into the battery stack.
Driver Shutdown Circuit
The driver shutdown block is essentially a simple level-shift circuit that monitors the system level shutdown signal
(SWITCH_EN) and the bg_good signal. If shutdown is high and/or bg_good is low then the driver output is forced
low and the driver enters a low power shutdown state. The bg_good signal indicates that the charge pump and
bandgap are powered up and functional. This circuit also indirectly ensures that the drivers will automatically shut
down if either the 5V or 12V supplies are not operational.
Floating Driver UVLO
A UVLO circuit is included in each driver to prevent the driver output from turning on unless its floating supply is
active.
Floating Driver Output Buffer
Figure 6 shows the architecture for the floating driver output buffer along with a dual-FET load. The output buffer
uses a two-stage parallel architecture to help control output currents that must be supplied by the charge pump.
A low-output-drive slewing stage begins every output transition and a parallel high-output-drive latching stage is
activated once the output has slewed to within 300mV(typical) of whichever rail it is approaching. The latching
stage also provides a low output impedance to hold the output on or off in the presence of external noise
transients. This architecture is used because all current provided by the output buffer to charge the external FET
switch gate-source capacitance (i.e. turn a switch 'ON') must be supplied to the VDDCP pin by the charge pump.
Turning a switch off is much simpler: all charge drained from the external FET gate-source capacitance flows into
the GATE pin, through the driver pull-down circuitry, and back out through the SOURCE pin.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
High-Current
Latch Stage
Low-Current
Slew Stage
MP0
MP2
+
-
+300 mV
Fixed 250 PA
Pullup
MP1
+
Comp1
-
External to EMB1428
Comparator
Enable
Signals
-
Comp2
SWITCH_EN
UVLO
+
100 k:
Bleeder
Resistor
MN1
Dual-FET
Switch
Enable
+
-
+300 mV
MN0
SOURCE
Pin
MN2
Slew Current
Level-Shift
Slew Signal
to
Digital Core
Figure 6. Floating Driver Output Buffer
The slewing output stage consists of a pull-up current source (MN0, MP0, and MP2) and a resistive pull-down
circuit (MN2, and 20K resistor). The pull-up slewing current is IGON. The approximate pull-up time can be
estimated using the model shown in Figure 7 where the input is a current step waveform. RBLD is the 100k
bleeder resistance, typical. Vo is the voltage to which the slewing stage pulls the gate voltage up to (12V-0.3V =
11.7V). The equation for the slewing time is:
IGON x RBLD
IGON x RBLD - Vo
tSLEW = Cgs x RBLD x ln(
)
(1)
Using the above equation along with a conservative estimate for the Cgs of the dual-FETs of 5nF gives pull-up
times of 316 µs (RBLD = 100k; Vo = 11.7V ).
The pull-down behavior of the slewing output stage is determined by the RC circuit formed by the 20K resistor,
the 100k bleeder resistor, and the Cgs of the external FETs. Using an analysis very similar to the above
equation, the pull-down time can be estimated at approximately 307 µs.
+
I
R
BLD
C
GS
GON
-
Figure 7. Driver Output Slewing Model
14
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
The latching output stage shown in Figure 6 consists of comparators Comp1 and Comp2 along with output
devices MP1 and MN1. Half of this stage is de-activated each time the output begins a transition so that it does
not conflict with the slewing stage. Comp1 and Comp2 receive an enable signal that switches them between
normal comparator operation and a low-power mode where their outputs are forced high (Comp1) or low
(Comp2) to unlatch. These comparators have a current output that is activated whenever the comparator is in
comparator mode but un-latched (i.e. the output is still slewing). These currents are wire-ORed and processed by
a level-shift circuit to produce a 5V logic slew signal. This slew signal is used by the digital core to control the
timing of the switch enable signals.
Charge Pump
The EMB1428 uses a two-stage charge pump architecture that is shown in Figure 8. The main components of
the charge pump are a soft start generator, clock level shift, output drivers, and a UVLO. This type of charge
pump produces a floating supply voltage, VCPP that is typically (2 x VDDP) - (3 x Vdiode) with no load. The
typical values for C1-C3 are expected to be 0.01 µF.
External to EMB1428
D1
FROM TOP OF BATTERY
STACK (60V)
C3
D2
D3
N2
N1
C1
C2
VDDCP
CEXT1
CEXT2
VSTACK
SOFT
START
VDDP
GNDP
CHARGE
PUMP
UVLO
1 MHz
CLK
LVL SHIFT
Internal
Clock
To Digital Block
Figure 8. Charge Pump
In steady-state, the signals at the CEXT1 and CEXT2 pins are square wave voltages that are 180° out of phase,
with an amplitude equal to the supply voltage VDDP. When CEXT1 is pulled low, C1 is charged through D1 to
VSTACK minus the diode drop. With no loading at the output of the charge pump, the capacitor C1 acts like a
simple electro-static level shift such that the CEXT1 square wave is reproduced at node N1 but switching
between VSTACK and VSTACK+VDDP. During the opposite clock phase, the phase difference between the
CEXT1 and CEXT2 pins allows charge to flow from C1 to C2 through D2 such that C2 is charged to
VSTACK+VDDP when N1 is high and N2 is low. The next phase of the clock causes N2 to be pushed up to
VSTACK + (2 x VDDP) through C2 which reverse biases D2 and forward biases D3. The D3/C3 circuit simply
rectifies this square wave and creates a DC voltage of approximately 2 x VDDP across C3. The voltage
developed across C3 is used as a floating supply for the VDDCP pin that is referenced to VSTACK. The VDDP
supply current is always 2 times the load current pulled from the output of the charge pump.
Charge Pump UVLO
A floating UVLO circuit is connected between the VDDCP and VSTACK pins to monitor the charge pump output.
The output of the UVLO has also been modified to produce the ground-referenced 5V cpgood signal through a
level-shift circuit. The UVLO trip points are listed in the ELECTRICAL CHARACTERISTICS table as VCP_UVH and
VCP_UVL
.
Serial Interface
The serial interface operates on 8-bit transactions. See Figure 9 for proper operation of the serial interface. The
microcontroller must send a 4-bit command on SDI followed by 4 zeros. The EMB1428 will provide fault[3:0] on
SDO (related to the previous command), followed by the 4-bit command that it just received. The EMB1428 will
drive SDO on the falling edge of SCLK and sample SDI on the rising edge of SCLK. The assertion of CS will
cause an internal signal sdo_en to go high and actively drive the SDO pin high or low. A short delay after CS has
been de-asserted, sdo_en will go low and the SDO pin will tri-state and be ready to be driven by other devices
on the SPI bus.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
t
t
t
CDSU
CSU
HD
CS
SCLK
cmd[3]
cmd[2]
fault[2]
cmd[1]
fault[1]
cmd[0]
fault[0]
SDI
SDO
fault[3]
cmd[3]
cmd[2]
cmd[1]
cmd[0]
sdo_en
t
t
HD
SU
t
DIS
Figure 9. Serial Interface (proper operation)
If CS goes high at any point before the 8th rising edge of SDI, the transaction will be considered aborted and the
data that was received on SDI will be discarded. No command change will occur from such a transaction.
However, if FAULT_INT was cleared by the transaction it will remain cleared and the fault data will no longer be
accessible.
t
TRANS
CS
Figure 10. Serial Interface (inter transaction timing)
The serial clock (SCLK) will be gated low outside this block (in the IO). Thus SCLK will always be low when CS
is high.
16
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
t
CDSU
CS
SCLK
cmd[3]
cmd[2]
cmd[1]
cmd[0]
SDI
Figure 11. Serial Interface (aborted transaction)
Command Decoding
The EMB1428 will receive the cmd[3:0] from the SPI interface, synchronize it into the internal clock domain, and
enable the switches according to the following table:
Table 2. Switch Settings for Each Command
SPI Command
cmd[3:0]
0_000
State of Cell Switches
CSW[7:0]
State of Polarity Switches
Description
PSW[3:0]
0000
1001
0110
1001
0110
1001
0110
1001
0000
1001
0110
1001
0110
1001
0110
1001
0000_0000
0000_0011
0000_0110
0000_1100
0001_1000
0011_0000
0110_0000
1100_0000
0000_0000
0000_0011
0000_0110
0000_1100
0001_1000
0011_0000
0110_0000
1100_0000
Open all switches
Connect Cell 1
Connect Cell 2
Connect Cell 3
Connect Cell 4
Connect Cell 5
Connect Cell 6
Connect Cell 7
Test Mode
0_001
0_010
0_011
0_100
0_101
0_110
0_111
1_000
1_001
Connect Cell 1
Connect Cell 2
Connect Cell 3
Connect Cell 4
Connect Cell 5
Connect Cell 6
Connect Cell 7
1_010
1_011
1_100
1_101
1_110
1_111
Power On Reset
The following will be asynchronously reset when the internal POR block is triggered:
1. Serial Interface
2. cmd[3:0] = 4’h0
3. FAULT_INT = 1’b0
4. EN = 1’b0
5. PSW[3:0] = 4’h0
6. CSW[7:0] = 8’h00
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
7. Shutdown Mode = yes
8. Internal Clock = off
9. Normal Mode/Test Mode = Normal Mode
The serial interface is reset so that it is prepared to detect aborted transactions. If POR block isn’t triggered, the
serial interface will still function. However the initial state of the part will be unknown, so the first transaction may
clock out a fault code.
Normal Control Sequencing
30176820
START
Command
Processed
DONE set
Enable FET
Switches for
Selected Cell
Wait for new
command
Reset EN, Wait
for DONE
Set DIR, check
DIR_RT
Internal Fault
Checking
Set EN
STOP
Command
Processed
DONE set
unexpectedly
Open all FET
Switches
Set FAULT_INT
output
Read FAULT
Pins
SLEEP
Figure 12. EMB1428 Flowchart
Switches are turned on one at a time to avoid drawing too much current from the charge pump. The following list
details the normal sequence that will be used for changing the Switch and EMB1499 Controls each time a new
command is received. Exceptions to the sequence (due to errors) will be explained later.
1. Wait for new command.
2. Set EN low.
3. Wait for DONE to be high.
4. Wait for those cell and polarity switches to be turned off as necessitated by the new command.
5. If new command is 4’b0_000 and the EMB1428 is in shutdown mode, go to #1. If new command is not
4’b0_000 and the EMB1428 is in shutdown mode, then exit shutdown mode.
6. Set DIR to be logically equal to the complement of cmd[3]
7. Wait for /DIR_RT to become logically equal to cmd[3]
8. If any switches are currently on, turn off the ones that are not needed for this new command. (All switches
can be turned off at once. Switches that are currently on and needed for the new command will not be turned
off.)
9. If any switches were turned off in #9, wait for them to complete their turn-off process.
10. If the new command is 4’b0_000 (open all switches), enter shutdown mode. Then go to #1. Otherwise,
continue with next step.
11. Turn on next cell switch that is currently off. If all requested cell switches are on, go to #14. (Order for
selecting the next cell switch does not matter.)
12. Wait for the cell switch to fully turn on. Then go to #12.
13. Turn on next polarity switch that is currently off. If all requested polarity switches are on, go to #16. (Order
for selecting the next polarity switch does not matter.)
14. Wait for the polarity switch to fully turn on. Then go to #14.
15. Set EN high.
16. Wait for DONE to go low.
17. Go to #1.
18
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
Any time a new command arrives, the EMB1428 immediately goes back to step #2, regardless of where it was at
in the sequence. Any time an error occurs that causes FAULT_INT to go high, the EMB1428 immediately goes
back to step #1 and acts as if it received a command to open all switches.
Emergency Shutdown
If the EMB1428 receives two consecutive commands to open all switches (no intervening commands), it will
immediately set {CSW[7:0], PSW[3:0]} = 12’h0. This allows all switches to be shut off if there is a problem in the
EMB1499 communication or in the EMB1428 charge pump circuitry.
An emergency shutdown will cause the EMB1428 to enter shutdown mode and turn off its internal clock within a
few clock cycles without waiting for switches to finish turning on or off.
EMB1499 Control Signaling
The DIR_RT from the EMB1499 will be synchronized into the EMB1428’s internal clock domain. On every rising
edge of the internal clock,DIR_RT will be compared to DIR. If they are ever at the same logic level, a fault will be
generated.
t
t
DIRSU
DIRSU
EN
DIR
DIR_RT
t
t
DIR
DIR
Figure 13. Direction Signals
Error Detection
The EMB1428 contains combinatorial circuitry that will monitor the CSW[7:0], PSW[3:0] outputs for any illegal
combination. If an illegal combination occurs, all 12 of the switch control outputs will be forced to zero. The
switch control outputs are allowed to glitch low as long as the glitches are typically less than 10ns in length.
These short glitches will not pass through the switch circuitry and cause a problem. The switch control output will
return to normal operation after the next serial transaction.
This circuitry is included in case the POR circuit does not function or if a radiation event occurs that could be
destructive to the battery pack.
The illegal combinations are:
1. More than two bits of CSW[7:0] set.
2. Two non-consecutive bits of CSW[7:0] set.
3. (PSW3 | PSW0) & (PSW2 | PSW1) = 1
Fault Reporting
The EMB1428 detects and reports faults from various sources. If a fault causes FAULT_INT to go high, the IC
will immediately act as if it received a command to open all switches: EN will go low, all switches will be turned
off, and the IC will enter sleep/shutdown mode. Some faults that are only detected by a subsequent serial
transaction do not trigger FAULT_INT and thus do not cause all switches to be opened.
The fault code should always be interpreted as a problem completing the prior command. Reading the fault code
clears the fault condition. The EMB1428 will always attempt to perform the command that was sent as the fault
code was being read. If two commands are sent in quick succession, a fault may be read when the second
command is sent because the first did not have time to complete. At this point, the EMB1428 will attempt to
perform the second command.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
Serial Interface Faults
If a 9th rising edge of SCLK is detected while CS is low (Figure 14), a fault will be generated and the IC will drive
FAULT_INT high.
CS
SCLK
FAULT_INT
t
INT
Figure 14. Serial Interface (too many clocks)
If SDI clocks in a high during any of the 4 bits when it should be low, a fault will be generated and the IC will
drive FAULT_INT high. See Figure 15.
CS
SCLK
cmd[3]
cmd[2]
cmd[1]
cmd[0]
SDI
FAULT_INT
t
INT
Figure 15. Serial Interface (invalid SDI high)
EMB1499 Control Faults
Incorrect DIR_RT
If DIR_RT matches DIR on any rising edge of the internal clock, a fault will be generated and the IC will drive
FAULT_INT high. This fault will be masked during serial transactions. If DIR_RT is the wrong value only during
the serial transaction, it will be masked and never reported.
20
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
Int. clock
DIR
DIR_RT
FAULT_INT
t
INT
Figure 16. Direction failure (DIR rising case)
EMB1499 Fault
If there is a rising edge on DONE while EN is high, the EMB1428 will detect it as an EMB1499 fault. If this
occurs, the EMB1428 will drive FAULT_INT high. If FAULT[2:0] ≠ 000, then the EMB1428 will output the
corresponding EMB1499 fault code.
The EMB1499 faults are masked during serial transactions. If an EMB1499 failure occurs between the start of a
serial transaction and the falling edge of EN, it will be masked and never reported.
UVLO Tripping
if a UVLO event occurs, the internal signal bg_good will be driven low. If a falling edge is seen on the internal
signal bg_good while the EMB1428 is in active mode, the EMB1428 will drive FAULT_INT high.
Previous Command Not Completed
If CS goes low and the EMB1428 has not completed its sequence from the previous command, this will generate
a fault. These fault conditions will be generated immediately and the fault code will be shifted out in the current
serial transaction. The EMB1428 will not drive FAULT_INT high in any of these situations.
If CS goes low and the EMB1428 is still waiting for DONE to go high (i.e. the EMB1428 is still waiting for the
EMB1499 to stop charging or discharging so it can set up for the command it received on the previous serial
transaction), then the EMB1428 will generate a fault.
If CS goes low and the EMB1428 has set EN high but is still waiting for DONE to go low, the EMB1428 will
generate a fault.
If CS goes low while slew is low or the EMB1428 is waiting for the falling edge of slew, the EMB1428 will
generate a fault.
If CS goes low while bg_good is low and the current command is not 4’h0 (open all switches), the EMB1428 will
generate a fault.
Clearing FAULT_INT
The EMB1428 will clear FAULT_INT between the 4th and 6th rising edges of the SCLK. Faults from the
EMB1499 that occur between the falling edge of CS and the point where DIR is set in the control sequence will
be ignored. This way, the user can be assured that triggered faults are always related to the current serial
command.
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: EMB1428Q
EMB1428Q
SNVS812A –MAY 2012–REVISED MAY 2013
www.ti.com
CS
SCLK
cmd[3]
cmd[2]
cmd[1]
cmd[0]
SDI
FAULT_INT
Figure 17. Clearing FAULT_INT
Generating Fault Codes
The EMB1428 will generate FAULT[3:0] according to the following table. This table is in order of priority. So if
multiple fault conditions occur, the fault code that is higher in the table will be generated.
Table 3. Fault Codes
Failure Description
fault[3:0]
{1’b0, FAULT[2:0]}
1100
FAULT_INT triggered?
DONE went high while EN was high and FAULT[2:0] ≠ 000
DONE went high while EN was high and FAULT[2:0] = 000
SDI sampled high when it should be low
9th SCLK rising edge seen while CS is low
DIR_RT is not the opposite of DIR
yes
yes
yes
1101
1110
1000
yes
no
CS falling edge while the EMB1428 is still waiting for a transition
on DONE (rising or falling edge)
CS falling edge while slew is low or the EMB1428 is waiting for it
to go high
1001
1011
no
no
CS falling edge while bg_good is low and the current command
is not 4’h0 (open all switches)
bg_good went low after it was sampled high
No fault condition
yes
yes
1010
22
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: EMB1428Q
EMB1428Q
www.ti.com
SNVS812A –MAY 2012–REVISED MAY 2013
REVISION HISTORY
Changes from Original (April 2013) to Revision A
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 22
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: EMB1428Q
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
EMB1428QSQ/NOPB
EMB1428QSQE/NOPB
EMB1428QSQX/NOPB
ACTIVE
ACTIVE
ACTIVE
WQFN
WQFN
WQFN
RHS
RHS
RHS
48
48
48
1000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
SN
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
EMB1428Q
SN
SN
EMB1428Q
EMB1428Q
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
EMB1428QSQ/NOPB
EMB1428QSQE/NOPB
EMB1428QSQX/NOPB
WQFN
WQFN
WQFN
RHS
RHS
RHS
48
48
48
1000
250
330.0
178.0
330.0
16.4
16.4
16.4
7.3
7.3
7.3
7.3
7.3
7.3
1.3
1.3
1.3
12.0
12.0
12.0
16.0
16.0
16.0
Q1
Q1
Q1
2500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
EMB1428QSQ/NOPB
EMB1428QSQE/NOPB
EMB1428QSQX/NOPB
WQFN
WQFN
WQFN
RHS
RHS
RHS
48
48
48
1000
250
356.0
208.0
356.0
356.0
191.0
356.0
35.0
35.0
35.0
2500
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号:
EMB19T2R
Small Signal Bipolar Transistor, 0.02A I(C), 50V V(BR)CEO, 2-Element, PNP, Silicon, EMT6, 6 PIN
ROHM
©2020 ICPDF网 联系我们和版权申明