INA300AIDSQR [TI]
36V 电流感应比较器 | DSQ | 10 | -40 to 125;型号: | INA300AIDSQR |
厂家: | TEXAS INSTRUMENTS |
描述: | 36V 电流感应比较器 | DSQ | 10 | -40 to 125 放大器 光电二极管 比较器 |
文件: | 总44页 (文件大小:2603K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INA300
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
INA300 过流保护、电流检测比较器
1 特性
3 说明
• 宽共模范围:0V 至36V
• 可选响应时间:
– 10µs、50µs、100µs
• 可编程阈值:
– 使用单个电阻调节
– 可编程范围为0mV 到250mV
• 精度:
– 失调电压:±500μV(最大值)
– 失调电压漂移:0.5μV/°C(最大值)
• 可选迟滞:
INA300 为过电流保护应用而设计,是一个电流检测比
较器,通过测量分流电阻器上形成的电压,并将该电压
与阈值电压输入水平进行比较,从而检测过电流。此器
件可在 0V 至 36V 的共模电压范围内测量该差分电压
信号,与电源电压无关。INA300 器件具有可调阈值范
围,此范围由单个外部限值设定电阻器来设置。可选迟
滞功能可调节比较器的运行情况,以适应 0mV 至
250mV 的宽输入信号范围。
器件上的开漏警报输出可配置为透明模式(输出状态与
输入状态保持一致)或锁存模式(清零锁存时清除报警
输出)。器件响应时间设置是可选的,10µs 内即可迅
速发出过流警报。
– 2mV、4mV、8mV
• 有源静态电流:135μA(最大值)
• 可选禁用模式
INA300 器件由 2.7V-5.5V 单电源供电运行,最大电源
电流消耗为 135µA。INA300 器件的额定工作温度范围
为 -40°C 至 +125°C,采用 WSON-10 和 VSSOP-10
封装。
– 已禁用静态电流:3.5μA(最大值)
– 已禁用输入偏置电流:500nA(最大值)
• 锁存模式可用时的开漏输出
2 应用
器件信息
封装(1)
WSON (10)
VSSOP (10)
封装尺寸(标称值)
2.00mm x 2.00mm
3.00mm × 3.00mm
器件型号
INA300
• 过流保护
• 计算机
• 服务器
• 电信设备
• 电源
• 电池充电器
(1) 如需了解所有可用封装,请参阅数据表末尾的封装选项附录。
2.7 V to 5.5 V
CBYPASS
0.1 µF
RPull-up
10 kꢀ
VS
INA300
Processor
GPIO
Power Supply
(0 V to 36 V)
ENABLE
LATCH
ALERT
LIMIT
IN+
GPIO
GPIO
DAC
+
CMP
IN-
œ
DELAY
Load
RLIMIT
HYS
GND
典型应用原理图
本文档旨在为方便起见,提供有关TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SBOS613
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
Table of Contents
7.4 Device Functional Modes..........................................18
8 Application and Implementation..................................22
8.1 Application Information............................................. 22
8.2 Typical Applications.................................................. 22
9 Power Supply Recommendations................................28
10 Layout...........................................................................29
10.1 Layout Guidelines................................................... 29
10.2 Layout Example...................................................... 30
11 Device and Documentation Support..........................32
11.1 Documentation Support.......................................... 32
11.2 接收文档更新通知................................................... 32
11.3 支持资源..................................................................32
11.4 Trademarks............................................................. 32
11.5 Electrostatic Discharge Caution..............................32
11.6 术语表..................................................................... 32
12 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings(1) ....................................4
6.2 ESD Ratings............................................................... 4
6.3 Recommended Operating Conditions.........................4
6.4 Thermal Information....................................................4
6.5 Electrical Characteristics.............................................5
6.6 Timing Requirements..................................................5
6.7 Typical Characteristics................................................6
7 Detailed Description......................................................10
7.1 Overview...................................................................10
7.2 Functional Block Diagram.........................................10
7.3 Feature Description...................................................10
Information.................................................................... 32
4 Revision History
注:以前版本的页码可能与当前版本的页码不同
Changes from Revision B (April 2016) to Revision C (June 2021)
Page
• Changed 图7-6 caption....................................................................................................................................16
Changes from Revision A (March 2014) to Revision B (April 2016)
Page
• 更改了数据表标题...............................................................................................................................................1
• 向数据表添加了VSSOP (DGS) 封装..................................................................................................................1
• 更改了“说明”部分的文本,使之更加清晰....................................................................................................... 1
• Moved storage temperature from Handling Ratings table to Absolute Maximum Ratings table.........................4
• Changed Handling Ratings to ESD Ratings....................................................................................................... 4
• Added DGS data to Thermal Information table ..................................................................................................4
Changes from Revision * (February 2014) to Revision A (March 2014)
Page
• 更改了产品预览数据表........................................................................................................................................1
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
5 Pin Configuration and Functions
IN+
1
2
3
4
5
10 HYS
INœ
9
8
7
6
VS
LIMIT
ENABLE
ALERT
GND
Thermal
Pad
DELAY
LATCH
图5-1. DSQ Package 10-Pin WSON Top View
IN+
INœ
HYS
1
2
3
4
5
10
9
VS
LIMIT
GND
DELAY
LATCH
8
ENABLE
ALERT
7
6
图5-2. DGS Package 10-Pin VSSOP Top View
表5-1. Pin Functions
PIN
NAME
I/O
DESCRIPTION
NO.
1
IN+
Analog input
Analog input
Connect to supply side of shunt resistor.
Connect to load side of shunt resistor.
2
IN–
Alert threshold limit input.
See Setting The Current-Limit Threshold for details on setting limit threshold.
3
LIMIT
Analog input
Digital input
4
5
6
7
8
9
ENABLE
ALERT
LATCH
DELAY
GND
Enable or disable selection input
Digital output Overlimit alert, active-low, open-drain output.
Digital input
Digital input
Analog
Transparent or latch mode selection input.
Response time selection input.
Ground
VS
Analog
Power supply, 2.7 V to 5.5 V.
Hysteresis setting input.
See Selectable Hysteresis for hysteresis settings.
10
HYS
Digital input
Thermal pad
This pad can be connected to ground or left floating.
—
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
6 Specifications
6.1 Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
UNIT
Supply voltage, VS
6
40
V
(2)
Differential (VIN+) –(VIN–
Common-mode (3)
LIMIT
)
–40
V
Analog inputs (IN+, IN–)
40
GND –0.3
GND –0.3
GND –0.3
GND –0.3
–40
Analog input
(VS) + 0.3
(VS) + 0.3
6
V
V
Digital inputs
LATCH, DELAY, ENABLE, HYS
Alert output
V
Operating temperature
Junction temperature, TJ
Storage temperature, Tstg
125
°C
°C
°C
150
150
–65
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) VIN+ and VIN– are the voltages at the IN+ and IN–terminals, respectively.
(3) Input voltage may exceed the voltage shown if the current at that terminal is limited to 5 mA.
6.2 ESD Ratings
VALUE
±2500
±1000
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
V(ESD)
Electrostatic discharge
V
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
2.7
NOM
12
MAX
5.5
UNIT
VCM
VS
Common-mode input voltage
Operating supply voltage
Delay setting
V
V
3.3
100
µs
°C
TA
Operating free-air temperature
125
–40
6.4 Thermal Information
INA300
THERMAL METRIC(1)
DSQ (WSON)
10 PINS
63.5
DGS (VSSOP)
10 PINS
169.4
59.1
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
79.5
33.9
89.6
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
7.8
8.5
ψJT
34.3
88.3
ψJB
RθJC(bot)
7.5
n/a
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
6.5 Electrical Characteristics
at TA = 25°C, VSENSE = VIN+ –VIN– = 0 mV, VS = 3.3 V, VIN+ = 12 V, VLIMIT = 10 mV, and DELAY = 100 µs (unless otherwise
noted)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
INPUT
VCM
Common-mode input voltage
Differential input voltage
0
0
36
V
VIN
250
mV
VIN = VIN+ –VIN–
VIN+ = 0 V to 36 V,
TA= –40°C to 125°C
CMR
VOS
Common-mode rejection
100
120
dB
VS = 3.3 V, DELAY = 100 μs
VS = +3.3 V, DELAY = 50 μs
VS = +3.3 V, DELAY = 10 μs(2)
TA= –40°C to 125°C
–75
–125
–350
0.1
–500
–500
–650
0.5
Offset voltage, RTI(1)
μV
dVOS/dT
PSR
Offset voltage drift, RTI(1)
μV/°C
μV/V
VS = 2.7 V to 5.5 V, VIN+ = 12 V,
TA= –40°C to 125°C
Power-supply rejection ratio
75
150
5
0.05
±0.1
20
10
IB
Input bias current
μA
μA
μA
Disable mode
0.5
IOS
ILIMIT
Input offset current
TA= 25°C
19.9
20.1
Limit threshold output current
19.85
20.15
TA= –40°C to 125°C
DIGITAL INPUT/OUTPUT
Delay = open, overdrive = 1 mV
Delay = GND, overdrive = 1 mV
Delay = VS, overdrive = 1 mV
HYS = open
10
50
100
2
tp
Alert propagation delay
μs
HYS
Hysteresis
HYS = GND
4
mV
HYS = VS
8
Latch, enable
1.4
6
6
VIH
High-level input voltage
Low-level input voltage
V
V
Delay, hysteresis
Latch, enable
VS –0.5
0
0
0.4
0.5
400
1
VIL
Delay, hysteresis
IOL = 3 mA
VOL
Alert low-level output voltage
ALERT terminal leakage input current
Digital leakage input current
50
0.1
1
mV
μA
μA
VOH = 3.3 V
2
0 ≤VIN ≤VS
POWER SUPPLY
VSENSE = 0 mV, TA = 25°C
115
2
135
150
TA = –40°C to 125°C
IQ
Quiescent current
μA
VSENSE = 0 mV, disable mode,
HYS = 2 mV
3.5
(1) RTI = referred-to-input.
(2) Absolute-maximum values are tested with the threshold limit set using the corresponding noise adjustment factor (NAF) value. See 节
7.3.7 for additional information on applying the NAF value.
6.6 Timing Requirements
MIN
NOM
1
MAX
UNIT
ms
µs
Start-up time
Enable time
Disable time
ten
300
20
tdis
µs
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
6.7 Typical Characteristics
at TA = 25°C, VS = 3.3 V, VIN+ = 12 V, alert pull-up resistor = 10 kΩ, and Delay = 100 µs (unless otherwise
noted)
Offset Voltage (µV)
Offset Voltage (µV)
C001
C002
Delay = 10 µs
Delay = 50 µs
图6-1. Input Offset Voltage
图6-2. Input Offset Voltage
0
œ100
œ200
œ300
œ400
œ500
œ600
Delay = 100 µs
Delay = 50 µs
Delay = 10 µs
2.5
3
3.5
4
4.5
5
5.5
Supply Voltage (V)
C004
Offset Voltage (µV)
C003
图6-4. Input Offset Voltage vs Supply Voltage
Delay = 100 µs
图6-3. Input Offset Voltage
0
œ50
2.5
2
œ100
œ150
œ200
œ250
œ300
œ350
œ400
œ450
œ500
1.5
1
0.5
0
œ0.5
œ1
œ1.5
œ2
100 us
50 us
10 us
œ2.5
œ50
œ25
0
25
50
75
100
125
150
œ50
œ25
0
25
50
75
100
125
150
Temperature (°C)
C006
Temperature (°C)
C005
图6-6. Common-Mode Rejection Ratio vs
图6-5. Input Offset Voltage vs Temperature
Temperature
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
6
5
4
3
2
1
0
10
8
6
4
2
0
-2
-4
-6
-8
-10
œ1
0
5
10
15
20
25
30
35
40
0
5
10
15
20
25
30
35
40
Common-Mode Voltage (V)
Common-Mode Voltage (V)
C007
C008
图6-7. Input Bias Current vs Common-Mode
图6-8. Input Bias Current vs Common-Mode
Voltage (Enabled)
Voltage (Disabled)
7
6.5
6
250
200
150
100
5.5
5
IB-
4.5
4
50
0
3.5
3
IB+
œ50
œ50
œ25
0
25
50
75
100
125
150
œ50
œ25
0
25
50
75
100
125
150
Temperature (°C)
Temperature (°C)
C009
C010
图6-9. Input Bias Current vs Temperature
图6-10. Input Bias Current vs Temperature
(Enabled)
(Disabled)
160
140
120
100
80
60
50
40
30
20
10
0
60
40
2.3
2.8
3.3
3.8
4.3
4.8
5.3
5.8
2.3
2.8
3.3
3.8
4.3
4.8
5.3
5.8
Supply Voltage (V)
Supply Voltage (V)
C011
C012
图6-11. Quiescent Current vs Supply Voltage
图6-12. Quiescent Current vs Supply Voltage
(Enabled)
(Disabled)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
180
160
140
120
100
80
6
5
4
3
2
1
0
60
Vs = 5.5V
Vs = 3.3V
Vs = 2.7V
40
Vs = 5.5V
Vs = 3.3V
Vs = 2.7V
20
0
œ50
œ25
0
25
50
75
100
125
150
œ50
œ25
0
25
50
75
100
125
150
Temperature (°C)
Temperature (°C)
C013
C014
图6-13. Quiescent Current vs Temperature
图6-14. Quiescent Current vs Temperature
(Enabled)
(Disabled)
200
10
ZZ
LL
190
9
ZL, LZ
ZL, LZ, HL, LH
180
170
160
150
140
130
120
110
100
ZH, HZ
LL
8
ZZ, ZH, HZ, HH
7
LH, HL
HH
6
5
4
3
2
1
2.5
3
3.5
4
4.5
5
5.5
C025
2.5
3
3.5
4
4.5
5
5.5
C026
Supply Voltage (V)
Supply Voltage (V)
Z = Floating
HYS –DELAY
L = Low
H = High
Z = Floating
L = Low
H = High
HYS –DELAY
图6-15. Quiescent Current vs HYS and DELAY
图6-16. Quiescent Current vs HYS and DELAY
Settings (Enabled)
Settings (Disabled)
20.5
20.25
20
10
9
8
7
6
5
4
3
2
1
0
8 mV Hysteresis
4 mV Hysteresis
2 mV Hysteresis
19.75
19.5
œ50
œ25
0
25
50
75
100
125
150
œ50
œ25
0
25
50
75
100
125
150
Temperature (°C)
Temperature (°C)
C015
C016
图6-17. Limit Current Source vs Temperature
图6-18. Hysteresis vs Temperature
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
Time (25 µs/div)
Time (100 µs/div)
C017
C018
图6-19. Alert Step Response
图6-20. Alert Response (Disable to Enable)
0
5
10
15
20
25
30
Time (µs)
C019
图6-21. Alert Response (Latch Mode to Transparent Mode)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
7 Detailed Description
7.1 Overview
The INA300 INA300 is a 36-V, common-mode comparator designed for overcurrent protection applications. To
reduce the system component count, this device combines the current-sense amplifier and threshold comparison
into a single product for the overcurrent detection function. Programming this comparison threshold is configured
through a single external resistor, which simplifies the current design while allowing for easy adjustments to the
threshold when needed. The threshold setting resistor value is selected based on an internal 20-µA current
source to achieve a corresponding signal to the voltage that develops across the current-sensing or current-
shunt resistor in series with the monitored load current.
The device is designed to accommodate a range of application requirements, including common-mode voltage,
noise thresholds, and signal ranges. A wide signal threshold range reaching up to 250 mV is available to
accommodate both power-sensitive applications requiring small dissipations across a current sense resistor and
larger current-sensing resistors used in lower current applications.
Additional features available with the INA300 INA300 device include a disable mode for reducing the current
consumption of the device to below 10 µA, an output mode selector to enable a latched or transparent alert
output, and a selectable hysteresis value and alert response delay.
The wide signal range of the device is further enhanced with an adjustable hysteresis value to adjust the
characteristics of the comparator, which allows for better accommodation of the full input range. The selectable
alert response delays present in the INA300 INA300 device assist in optimizing device operation to account for
the system noise levels and operating characteristics required from this device. Longer delay settings allow for
added rejection of system noise, thus reducing the potential for false alerts resulting from noise spikes that can
occur in high-speed comparators.
7.2 Functional Block Diagram
VS
VPULL-UP
INA300-Q1
HYS
Level
Detection
Power Supply
(0 V to 36 V)
DELAY
ALERT
IN+
+
Control
Logic
INœ
Load
LATCH
LIMIT
GND ENABLE
Copyright © 2016, Texas Instruments Incorporated
7.3 Feature Description
7.3.1 Selecting a Current-Sensing Resistor
The device measures the differential voltage developed across a resistor when current flows through it to
determine if the monitored current exceeds a defined limit. This resistor is referred to as a current-sensing
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
resistor or a current-shunt resistor, with each term used interchangeably. The flexible design of the device allows
for measuring a wide differential input signal range across this current-sensing resistor, which can extend up to
250 mV.
Selecting the value of this current-sensing resistor is based primarily on two factors: the required accuracy of the
current measurement and the allowable power dissipation across the current-sensing resistor. Larger voltages
developed across this resistor allow more accurate measurements. This large signal accuracy improvement
results from the fixed internal amplifier errors that are dominated by the inherent input offset voltage of the
device. When the input signal decreases, these fixed internal amplifier errors become a larger portion of the
measurement and increase the uncertainty in the measurement accuracy. When the input signal increases, the
measurement uncertainty is reduced because the fixed errors are a smaller percentage of measured signal.
A system design trade-off for improving the measurement accuracy using larger input signals is the increase in
power across the current-sensing resistor. Increasing the value of the current-shunt resistor increases the
differential voltage developed across the resistor when current passes through the component. This increase in
voltage across the resistor increases the power that the resistor must be able to dissipate. Decreasing the value
of the current-shunt resistor value reduces the power dissipation requirements of the resistor, but increases the
measurement errors resulting from the decreased input signal. Selecting the optimal value for the shunt resistor
requires factoring both the accuracy requirement for the specific application and the allowable power dissipation
of this component.
An increasing number of low ohmic-value resistors are becoming available with values as low as 200 µΩ, with
power dissipations of up to 5 W that enable large currents to be monitored with sensing resistors.
7.3.1.1 Selecting a Current-Sensing Resistor: Example
In this example, the trade-offs involved in selecting a current-sensing resistor are discussed. This example
requires a 5% measurement accuracy for detecting a 10-A overcurrent event at a 50-µs delay setting where only
250 mW is allowable for the dissipation across the current-sensing resistor at the full-scale current level.
Although the maximum power dissipation is defined as 250 mW, a lower dissipation is preferred to improve
system efficiency. Some initial assumptions are made that are used in this example: the limit setting resistor,
RLIMIT, is a 1% component and the maximum tolerance specification for the internal threshold setting current
source, 0.5%, is used. Given the total error budget of 5%, up to 3.5% of error is available to be attributed to the
internal offset of the device.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
As shown in 表7-1, the maximum value calculated for the current-sensing resistor with these requirements is 2.5
mΩ. Although this value satisfies the maximum power dissipation requirement of 250 mW, headroom is
available from the 5% maximum total error to reduce the value of the current-sensing resistor and reduce the
power dissipation further. Selecting a 1.5-mΩ, current-sensing resistor value offers a tradeoff for reducing the
power dissipation in this scenario by approximately 40%, while still remaining within the defined accuracy region.
表7-1. Calculating the Current-Sensing Resistor, RSENSE
PARAMETER
EQUATION
VALUE
UNIT
Maximum measurement error
Maximum current
5%
IMAX
10
A
Maximum allowable RSENSE power
dissipation
2
PRSENSE
RSENSE × IMAX
250
mW
Initial error
RLIMIT + ILIMIT tolerances
1.5%
2.5
2
RSENSE_MAX
VSENSE_MAX
VOS Error
Maximum sensing resistor value
Input sense voltage
PRSENSE / IMAX
mΩ
RSENSE_MAX × IMAX
25
mV
Offset voltage error
(VOS / VSENSE_MAX) × 100
Maximum Error –Initial Error
VOS / (Error_Available / 100)
VSENSE_MIN / IMAX
2%
Error_Available
VSENSE_MIN
RSENSE_MIN
PRSENSE_MIN
Maximum allowable offset error
Minimum input sense voltage
Minimum sensing resistor value
Minimum power dissipation
3.5%
14.3
1.43
143
mV
mΩ
mW
2
RSENSE_MIN × IMAX
7.3.2 Setting The Current-Limit Threshold
The device determines if an overcurrent event is present by comparing the measured differential voltage
developed across the current-sensing resistor to the corresponding signal programmed at the LIMIT terminal.
The threshold voltage for the LIMIT terminal can be set using a resistor or an external voltage source.
7.3.2.1 Resistor-Controlled Current Limit
The typical approach for setting the limit threshold voltage is to connect a resistor from the LIMIT terminal to
ground. The value of this resistor, RLIMIT, is chosen to create a corresponding voltage at the LIMIT terminal
equivalent to the voltage, VTRIP, developed by the load current flowing through the current-sensing resistor. An
internal 20-µA current source is present at the LIMIT terminal that creates the corresponding voltage depending
on the value of RLIMIT. In the equations from 表 7-2, VTRIP represents the overcurrent threshold the device is
programmed to monitor for and VLIMIT is the programmed signal set to detect the VTRIP level. The term noise
adjustment factor (NAF) is included in the VLIMIT equation for the 10-µs delay setting. This value is equal to 500
µV and adjusts the operating point for the internal noise in this delay setting. The 50-µs and 100-µs delay
settings do not use the NAF term in calculating the VLIMIT threshold. See Noise Adjustment Factor (NAF) for
more details on the noise adjustment factor.
In 表7-2, the process for calculating the required value for RLIMIT to set the appropriate threshold voltage, VLIMIT
,
is shown. This calculation is based on the 10-µs delay setting so the NAF term is included in the calculation. For
a delay setting of 50 µs or 100 µs, the NAF term is omitted.
表7-2. Calculating the Limit Threshold Setting Resistor, RLIMIT
PARAMETER
EQUATION
VTRIP
VLIMIT
VLIMIT
RLIMIT
RLIMIT
Desired current trip value
Programmed threshold limit voltage
Threshold voltage
ILOAD × RSENSE
VLIMIT = VTRIP
(1)
(1)
(1)
(ILIMIT × RLIMIT) –NAF
(VLIMIT + NAF) / ILIMIT
(VLIMIT + 500 µV) / 20 µA
Threshold limit setting resistor
Limit setting resistor
(1) NAF is used with the 10-µs delay setting. NAF can be omitted in the RLIMIT calculation for the 50-µs and 100-µs delay settings.
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
TI recommends using NAF in calculating the value for VLIMIT and RLIMIT at the 10-µs delay setting. Removing
NAF from the VLIMIT and RLIMIT calculation at the 10-µs delay setting lowers the trigger point of the alert output.
Lowering the trigger point results in the device issuing an overcurrent alert prior to reaching the corresponding
VTRIP threshold. The averaging effect included with the 50-µs and 100-µs delay settings inherently eliminates the
effect internal noise has on the threshold voltage.
7.3.2.2 Voltage Source-Controlled Current Limit
The second method for setting the limit voltage is to connect the LIMIT terminal to a programmable DAC (digital-
to-analog converter) or other external voltage source. The benefit of this method is the ability to adjust the
current limit to account for different threshold voltages that are used for different system operating conditions.
For example, this method can be used in a system that has one current-limit threshold level that must be
monitored during the power-up sequence but different thresholds must be monitored during other system
operating modes.
In 表 7-3, VTRIP represents the overcurrent threshold the device is programmed to monitor for and VSOURCE is
the programmed signal set to detect the VTRIP level. NAF is included in the VSOURCE equation for the 10-µs delay
setting. This value equals 500 µV and is adjusts the operating point for the noise in the delay setting. The 50-µs
and 100-µs delay settings do not use the NAF term in calculating the VSOURCE threshold. For these delay
settings, the NAF term is omitted. See the Noise Adjustment Factor (NAF) section for more details on the noise
adjustment factor.
表7-3. Calculating the Limit Threshold Voltage Source, VSOURCE
PARAMETER
EQUATION
ILOAD × RSENSE
VTRIP + NAF
VTRIP
Desired current trip value
(1)
(1)
VSOURCE
VSOURCE
Programmed threshold limit voltage
Programmed signal set to detect the VTRIP level
VTRIP + 500 µV
(1) NAF is used with the 10-µs delay setting. NAF can be omitted in the VSOURCE calculation for the 50-µs and 100-µs delay settings.
TI recommends using NAF in calculating the value for VSOURCE at the 10-µs delay setting. Removing NAF from
the VSOURCE calculation at the 10-µs delay setting lowers the trigger point of the alert output. Lowering the
trigger point results in the device issuing an overcurrent alert prior to reaching the corresponding VTRIP threshold.
The averaging effect included with the 50-µs and 100-µs delay settings inherently eliminates the effect internal
noise has on the threshold voltage.
7.3.3 Delay Setting
The device response time for overcurrent events is adjustable based on the DELAY terminal setting. Three
response time settings are available, ranging from 10 µs to 100 µs. The primary purpose for the three different
delay settings is to offer a trade-off between a faster alert response and a more precise overcurrent threshold
level detection.
The device has a 10-µs internal comparison window. This single comparison window is the fundamental time
unit used for all three delay settings. For the 10-µs delay setting, the device compares the average of the input
signal during the 10-µs comparison window to the threshold limit programmed at the LIMIT terminal. If the
averaged input signal exceeds the threshold at the end of the 10-µs comparison window, the output alert triggers
and pulls the ALERT terminal low. However, if the averaged input does not exceed the threshold at the end of
the 10-µs comparison window, there is no change in the output alert status, which remains high to indicate that
no overcurrent event is detected.
For the 50-µs delay setting, there must be five consecutive 10-µs comparison windows that result in an average
input signal exceeding the threshold limit in order for the output alert to trigger and pull the ALERT terminal low.
If any single 10-µs comparison window fails to detect an overcurrent condition before reaching five consecutive
overcurrent comparisons, the internal counter is reset and no output alert is issued. With the internal counter
reset, a new group of five consecutive 10-µs comparison windows of overcurrent conditions are required in order
to trigger the alert and pull the ALERT terminal low.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
The 100-µs delay setting operates in the same manner as the 50-µs method, but instead requires ten
consecutive 10-µs comparison windows with an input signal exceeding the threshold limit to issue an output alert
and pull the ALERT terminal low.
Requiring multiple consecutive overcurrent detections aides significantly in reducing the likelihood of system
noise causing false alerts, which can be detrimental to critical system operations. However, by enabling an alert
window equal to the comparison window of 10 µs, the device still has the flexibility to be used in fast overcurrent
detection applications that require quick responses to rapidly changing system operating characteristics.
In 图7-1, the device alert output response is shown for a 10-µs delay setting and a 50-µs delay setting based on
the same input signal condition. The initial increase of the input signal, VIN, above the VLIMIT level remains above
the limit for approximately 30 µs. With the device set to the 10-µs delay setting, the overcurrent condition is
detected and the alert output terminal is pulled low approximately 10 µs later. With the device set to the 50-µs
delay setting, an alert is not issued because five consecutive 10-µs overcurrent measurements are not detected.
With the input signal only being over the limit for 30 µs rather than the corresponding 50 µs needed for this delay
setting, the device does not issue an alert under this condition. For the second instance where VIN rises above
the VLIMIT threshold, the input remains above the limit for more than five consecutive 10-µs measurements,
indicating an overcurrent condition and the alert output terminal is pulled low.
Transparent Mode
VLIMIT
VIN
)
(VIN+ - VIN-
0V
ALERT
(Delay = 10 µs)
10 µs
10 µs
10 µs
10 µs
10 µs
10 µs
ALERT
(Delay = 50 µs)
50 µs
No Alert
50 µs
50 µs
No Alert
10 µs
图7-1. DELAY Terminal Settings
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
As discussed previously, there are three different available delay settings that are configured based on the signal
connected to the DELAY terminal, as shown in 图7-2 and 表7-4. The DELAY terminal must be either connected
directly to ground, directly to supply, or left completely floating. Additional external resistors must not be
connected to this terminal. If a resistance is required by the application to be placed in series with either the
supply or ground connection to the DELAY terminal, this resistance must be limited to 1 kΩ so as to not conflict
with the internal level-detection circuitry.
VS
DELAY
GND
图7-2. Delay Response
表7-4. Delay Settings
DELAY
Open or floating
GND
ALERT DELAY (µs)
10
50
VS
100
7.3.4 Alert Timing Response
The device has a 10-µs internal comparison window where the input signal is measured to compare to the limit
threshold voltage. This window continuously runs internal to the device without any external indicator or control.
A comparison is made at the completion of each 10-µs comparison window to determine if the averaged input
over the comparison window exceeds the limit threshold, thus indicating if an overcurrent event has occurred.
This comparison window is not synchronized with the input signal so there is an unknown timing component
present. With this free-running internal timing window, an overcurrent event can occur anywhere within the 10-µs
comparison window. This condition causes a variation in the amount of time before the alert appears at the
output because the comparison is always made at the end of the 10-µs comparison window. 图 7-3 shows the
variation in time between when the input signal rises above the threshold voltage and when a change at the alert
output terminal occurs.
Limit Threshold
Time (2 µs/div)
C020
图7-3. 10-µs Alert Response Window
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
The delay shown in 图7-3 represents the response time of the device with a 10-µs delay setting. With a
50-µs delay setting, an additional 40 µs is added to the timing response, as shown in 图 7-4. A 100-µs delay
setting adds 90 µs to the response time, as shown in 图7-5.
Limit Threshold
Limit Threshold
Time (10 µs/div)
Time (5 µs/div)
C021
C022
图7-4. 50-µs Alert Response Window
7.3.5 Selectable Hysteresis
图7-5. 100-µs Alert Response Window
Device hysteresis is adjustable based on the setting at the hysteresis (HYS) terminal. The smallest setting for
hysteresis on the device, 2 mV, is enabled by leaving the HYS terminal open and floating. A 4-mV hysteresis is
set by connecting the HYS terminal to ground; connecting this terminal to the supply voltage sets the hysteresis
to 8 mV, as shown in 图 7-6. The HYS terminal must be either connected directly to ground, directly to supply, or
left completely floating. Additional external resistors must not be connected to this terminal. If a resistance is
required by the application to be placed in series with either the supply or ground connections to the HYS
terminal, this resistance must be limited to 1 kΩso as to not conflict with the internal level-detection circuitry.
VS
HYS
GND
图7-6. Hysteresis
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
The wide dynamic input range of the INA300 INA300 necessitates an adjustable hysteresis to ensure that the
device can be appropriately configured based on the specific operating conditions and application requirements.
图 7-7 illustrates the transition locations for the ALERT terminal based on where the input signal, VIN, is
measured relative the limit threshold, VLIMIT. The corresponding hysteresis levels and physical terminal settings
for the device are shown in 表7-5.
VOUT
Alert
Output
VIN
VLIMIT - Hysteresis
VLIMIT
图7-7. Typical Comparator Hysteresis
表7-5. Hysteresis Settings
HYSTERESIS
HYSTERESIS SETTING
Float
GND
VS
2 mV
4 mV
8 mV
7.3.6 Alert Output
The device ALERT terminal is an active-low, open-drain output. This output is designed to be pulled low when
the input conditions are detected as out-of-range. This open-drain output pin is recommended to include a
10-kΩ, pull-up resistor to the supply voltage. This open-drain terminal can be pulled up to a voltage beyond the
supply voltage, VS, but must not exceed 5.5 V.
7.3.7 Noise Adjustment Factor (NAF)
The device is a high-speed, low-noise comparator that is designed to alert when the measured input signal
exceeds the programmed limit level. Internal noise in the device couples into the measurement and can result in
alerts being issued prior to the input signal exceeding the voltage level present at the LIMIT terminal. This known
internal noise component effects the input signal measurement by causing a consistent shift in the device
internal offset, resulting in a shifted trip threshold. NAF adjusts the VLIMIT setting to account for this internal shift,
thus allowing for a more precise level detection of the measured current.
The NAF value is based on the noise contribution on the measurement at the 10-µs delay setting. This value is
equal to 500 µV and is applied in the calculation to adjust the VLIMIT threshold level to allow for a more accurate
alert trip point. The NAF term is only applied in the VLIMIT calculation at the 10-µs delay setting. The averaging
effect included with the 50-µs and 100-µs delay settings inherently eliminates the effect internal noise has on the
threshold voltage. The NAF term can be omitted from the RLIMIT calculation at the 10-µs delay setting with the
effect of a lower trigger point of the alert output. Lowering the trigger point results in an overcurrent alert prior to
reaching the corresponding VTRIP threshold.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
7.4 Device Functional Modes
7.4.1 Alert Mode
The device has two output operating modes that are selected based on the LATCH terminal setting: transparent
mode and latch mode. These modes change how the ALERT terminal responds to the changing input signal
conditions.
7.4.1.1 Transparent Output Mode
The device is set to transparent mode when the LATCH terminal is pulled low, thus allowing the output alert state
to change and follow the input signal with respect to the programmed alert threshold. For example, when the
differential input signal rises above the alert threshold, the alert output terminal is pulled low. When the
differential input signal drops below the alert threshold for 10 µs, the output returns to the default high output
state. A common implementation using the device in transparent mode is to connect the ALERT terminal to a
hardware interrupt input on a controller. As soon as an overcurrent condition is detected in the device and the
ALERT terminal is pulled low, the controller interrupt terminal detects the output state change and can begin
making changes to the system operation needed to address the overcurrent condition.
7.4.1.2 Latch Output Mode
Some applications do not have the functionality available to continuously monitor the state of the output ALERT
terminal to detect an overcurrent condition. A typical example of this application is a system that is only able to
poll the ALERT terminal state periodically to determine if the system is functioning correctly. If the device is set to
transparent mode in this type of application, missing the change in state of the ALERT terminal is possible when
ALERT is pulled low to indicate an out-of-range event if the out-of-range condition does not appear during one of
these periodic polling events.
Latch mode is specifically intended to accommodate these applications. As shown in 表7-6, the device is placed
in latch mode by setting the voltage on the LATCH terminal to a logic high level. The difference between latch
mode and transparent mode is how the alert output responds when an overcurrent event ends. In transparent
mode, when the differential input signal drops below the limit threshold level for 10 µs, the output state returns to
the default high setting to indicate that the overcurrent event had ended.
In latch mode, when an overlimit condition is detected and the ALERT terminal is pulled low, the ALERT terminal
does not return to the default high level when the differential input signal drops below the alert threshold level for
10 µs. To clear the alert the LATCH terminal must be pulled low for at least 20 µs. Pulling the LATCH terminal
low allows the ALERT terminal to return to the default high level, provided that the differential input signal has
dropped below the alert threshold. If the input signal is still above the threshold limit when the LATCH terminal is
pulled low, the ALERT terminal remains low. When the alert condition is detected by the system controller (the
LATCH terminal) can be set back to high in order to place the device back in latch mode.
表7-6. Output Mode Settings
OUTPUT MODE
Transparent mode
Latch mode
LATCH TERMINAL SETTING
LATCH = low
LATCH = high
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
The latch and transparent modes are represented in 图 7-8. In 图 7-8 when VIN drops back below the VLIMIT
threshold for the first time, the LATCH terminal is pulled high. With the LATCH terminal pulled high, the device is
set to latch mode so that the alert output state does not return high when the input signal drops below the VLIMIT
threshold. Only when the LATCH terminal is pulled low does the ALERT terminal return to the default high level,
indicating that the input signal is below the limit threshold. When the input signal drops below the limit threshold
for the second time, the LATCH terminal is already pulled low. The device is set to transparent mode at this point
and the ALERT terminal is pulled back high when the input signal drops below the alert threshold.
VLIMIT
VIN
(VIN+ - VIN-
)
0 V
ALERT
LATCH
图7-8. Transparent vs Latch Mode
7.4.2 Disable Mode
The INA300 INA300 device has an ENABLE terminal that allows the device to be placed into an active enabled
state or a low-power disabled state where less than 10 µA is consumed from all terminals. This disable state
allows the device to be used in applications where low current consumption is required to extend battery life
where constant monitoring is not required. The INA300 device requires approximately 20 µs to enter the low-
power state when the ENABLE terminal transitions from high to low, as shown in 表7-7. To return to the enabled
active state, the INA300 device requires approximately 300 µs to return to normal operation when the ENABLE
terminal transitions from low to high, taking the device out of the low-power state.
表7-7. Enable and Disable Mode Settings
ENABLE MODE
Disable mode
Enable mode
ENABLE TERMINAL SETTING
ENABLE = low
ENABLE = high
The internal counter that determines if the necessary consecutive 10-µs window comparison alert conditions are
reached for the 50-µs and 100-µs delay setting is reset when the device is put into a disabled state. When the
device is re-enabled, the counter restarts.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
7.4.3 Input Filtering
External system noise can have a significant effect in the ability of a comparator to accurately measure and
detect whether input signals exceed the reference threshold levels, indicating an overrange condition. The
device is susceptible to external noise, although the 50-µs and 100-µs delay settings are can mitigate the impact
of noise based on the effective averaging achieved in these modes. The obvious effect that external noise can
have on the operation of a comparator is to cause a false alert condition. If a comparator detects a large noise
transient coupled into the signal, the device can interpret this transient as an overrange condition.
External filtering can help reduce the amount of noise that reaches the comparator inputs, and can reduce the
likelihood of a false alert from occurring. The tradeoff to adding this noise filter is increased comparator response
time, because of the input signal being filtered as well as the noise. 图 7-9 shows the implementation of an input
filter for the device.
+2.7 V to 5.5 V
C
BYPASS
0.1 µF
INA300-Q1
R
VS
Pull-up
10 kꢀ
Power Supply
(0 V to 36 V)
ENABLE
LATCH
IN+
+
ALERT
LIMIT
R
FILTER
≤100 ꢀ
CMP
C
INœ
FILTER
œ
DELAY
Load
R
HYS
GND
LIMIT
Copyright © 2016, Texas Instruments Incorporated
图7-9. Input Filter
Limiting the amount of input resistance used in this filter is important because this resistance can have a
significant effect on the input signal that reaches the device input pins resulting from the device input bias
currents. A typical system implementation involves placing the current-sensing resistor near the device so the
traces are short and the trace impedance is small. This layout helps reduce the ability of coupling additional
noise into the measurement. Under these conditions, the characteristics of the input bias currents have minimal
effect on device performance.
As shown in 图 7-10, the input bias currents increase in opposite directions when the differential input voltage
increases. This increase results from the design of the device, which allows common-mode input voltages to far
exceed the device supply voltage range. With input filter resistors now placed in series with these unequal input
bias currents, there are unequal voltage drops developed across the input resistors. The difference between the
two drops appears as an added signal that (in this case) subtracts from the voltage developed across the
current-sensing resistor, reducing the signal that reaches the device input terminals. Smaller value input resistors
reduce this effect of signal attenuation to allow for a more accurate measurement.
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
30
25
20
15
10
5
IB+
0
IB-
œ5
œ10
œ15
œ20
0
50
100
150
200
250
Differential Input Voltage (mV)
C027
图7-10. Input Bias Current vs Differential Input Voltage
For example, with a differential voltage of 10 mV developed across a current-sensing resistor and using 100-Ω
resistors, the differential signal that reaches the device is 9.8 mV. A measurement error of 2% is created as a
result of the external input filter resistors. Using 10-Ωinput filter resistors instead of the 100-Ωresistors reduces
this added error from 2% to 0.2%.
7.4.4 Using the INA300 INA300 With Common-Mode Transients Above 36 V
With a small amount of additional circuitry, the device can be used in circuits subject to transients higher than
36 V. Use only zener diodes or zener-type transient absorbers (sometimes referred to as Transzorbs). Any other
type of transient absorber has an unacceptable time delay. Start by adding a pair of resistors, as shown in 图
7-11, as a working impedance for the zener diode. Keeping these resistors as small as possible is best,
preferably 100 Ω or less. Larger values can be used with an additional error induced resulting from a reduced
signal that reaches the device input terminals. Because this circuit limits only short-term transients, many
applications are satisfied with a 100-Ω resistor along with conventional zener diodes of the lowest power rating
available. This combination uses the least amount of board space. These diodes can be found in SOT-523 or
SOD-523 packages.
+2.7 V to 5.5 V
C
BYPASS
0.1 µF
TI Device
R
Pull-up
VS
10 k
Power Supply
(0 V to 36 V)
ENABLE
LATCH
IN+
IN–
+
ALERT
LIMIT
R
PROTECT
≤100 Ω
CMP
–
DELAY
Load
R
HYS
GND
LIMIT
图7-11. Transient Protection
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
8 Application and Implementation
Note
以下应用部分中的信息不属于TI 器件规格的范围,TI 不担保其准确性和完整性。TI 的客 户应负责确定
器件是否适用于其应用。客户应验证并测试其设计,以确保系统功能。
8.1 Application Information
The INA300 INA300 is designed to enable configuration for detecting overcurrent conditions in an application.
This device is individually targeted towards overcurrent detection of a single threshold. However, this device can
be paired with additional devices and circuitry to create more complex monitoring functional blocks.
8.2 Typical Applications
8.2.1 Unidirectional Operation
2.7 V to 5.5 V
C
BYPASS
0.1
F
R
PULL-UP
10 k
V
S
TI Device
ENABLE
Processor
GPIO
Power Supply
(0 V to 36 V)
LATCH
IN+
IN–
GPIO
GPIO
DAC
+
–
ALERT
LIMIT
CMP
DELAY
Load
R
LIMIT
HYS
GND
图8-1. Unidirectional Application Schematic
8.2.1.1 Design Requirements
The INA300 device measures current through a resistive shunt with current flowing in one direction, enabling
detection of an overcurrent event only when the differential input voltage exceeds the threshold limit.
8.2.1.2 Detailed Design Procedure
图8-1 shows the basic connections of the INA300 device. The input terminals, IN+ and IN–, must be connected
as closely as possible to the current-sensing resistor to minimize any resistance in series with the shunt
resistance. Additional resistance between the current-sensing resistor and input terminals can result in errors in
the measurement. When input current flows through this external input resistance, the voltage developed across
the shunt resistor can differ from the voltage reaching the input terminals.
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
8.2.1.3 Application Curve
图 8-2 shows the alert response transitioning from a high to a low state following the input signal exceeding the
limit threshold voltage. The time required for the output to respond varies as a result of when the input signal
crosses the threshold limit voltage relative to where in the continuous running internal 10-µs comparison window
the overrange condition occurs. In 图8-2, the output response varies from roughly 2 µs to approximately
12 µs when the input exceeds the threshold level. This variance is a result of where in the 10-µs comparison
window the overrange event occurs. If the overrange event occurs late in the 10-µs comparison window and is
large enough to average the entire window measurement up above the threshold level, the alert appears to
respond very quickly. If the alert occurs late in the 10-µs comparison window and is not large enough to average
the entire window measurement up above the threshold level, the alert does not appear until the next 10-µs
comparison window completes, assuming the input signal remains above the threshold for the entire duration.
Limit Threshold
Time (2 µs/div)
C020
图8-2. Alert Response
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
8.2.2 Bidirectional Operation
CBYPASS
0.1 µF
+2.7 V to 5.5 V
RPull-up
10 kꢀ
VS
IN+
IN-
+
-
OCP+
CMP
Power Supply
(0 V to 36 V)
LIMIT
GND
Output
CBYPASS
0.1 µF
Current
+2.7 V to 5.5 V
RPull-up
10 kꢀ
VS
IN+
IN-
+
-
Load
CMP
OCP-
LIMIT
GND
图8-3. Bidirectional Application
8.2.2.1 Design Requirements
Although the INA300 device is only able to measure current through a current-sensing resistor flowing in one
direction, a second INA300 INA300 device can be used to create a bidirectional monitor.
8.2.2.2 Detailed Design Procedure
With the input terminals of a second INA300 device reversed across the same current-sensing resistor, the
second INA300 device is now able to detect current flowing in the other direction relative to the first device, as
shown in 图 8-3. The outputs of each INA300 device connect to an AND gate to detect if either of the limit
threshold levels are exceeded. The output of the AND gate is high if neither overcurrent limit thresholds are
exceeded. A low output state of the AND gate indicates that either the positive overcurrent limit or the negative
overcurrent limit are surpassed.
表8-1. Bidirectional Overcurrent Output Status
OCP STATUS
OUTPUT
OCP+
0
0
1
OCP–
No OCP
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
8.2.2.3 Application Curve
图 8-4 illustrates two INA300 INA300 devices being used in a bidirectional configuration and an output control
circuit to detect if one of the two alerts is exceeded.
Positive Limit
0V
Negtive Limit
Time (5 ms/div)
C024
图8-4. Bidirectional Application Curve
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
8.2.3 Window Comparator
CBYPASS
0.1µF
+2.7 V to 5.5 V
RPull-up
10 kꢀ
VS
IN+
IN-
+
-
OCP+
CMP
Power Supply
(0 V to 36 V)
LIMIT
GND
Output
CBYPASS
0.1 µF
+2.7 V to 5.5 V
RPull-up
10 kꢀ
VS
IN+
IN-
+
-
Load
CMP
OCP-
LIMIT
GND
图8-5. Window Comparator Application
8.2.3.1 Design Requirements
The INA300 device can be used to create a window comparator function, detecting whether the current being
monitored is within a programmed range or has fallen outside of the expected operating region.
8.2.3.2 Detailed Design Procedure
图 8-5 shows how the window comparator function is setup using two INA300 devices. The input terminals of
each INA300 device are connected to the same current-sensing resistor. The limit threshold for the top device is
set to the upper limit of the window range. The bottom device limit threshold is set to the desired lower limit of
the range. With a logic inverter placed at the output of the device monitoring the lower limit, the OCP– signal is
high when the input signal is above the lower limit threshold. The OCP+ signal is high when the input signal is
below the upper limit threshold. A high value at the output (output of the AND gate) indicates that the monitored
current is operating within the desired window range.
表8-2. Window Comparator Output Status
INPUT CONDITION
Above range
Below range
In range
OUTPUT STATUS
0
0
1
Copyright © 2021 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
8.2.3.3 Application Curve
图8-6 shows the output waveform from the device window comparator application. In 图8-6, the output signal is
high when OCP– is low (the input signal is above the lower limit) and when OCP+ is high (the input signal is
below the upper limit). If the signal rises above the upper limit or drops below the lower limit, the corresponding
OCP output changes state, causing the state of the output (following the AND gate) to change to zero to indicate
an out-of-range condition.
Output
OCP-
OCP+
Upper Limit
Lower Limit
Time (2 ms/div)
C023
图8-6. Output Waveform
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
9 Power Supply Recommendations
The INA300 device input circuitry can accurately measure signals on common-mode voltages beyond the power-
supply voltage, VS. For example, the voltage applied to the VS power-supply terminal can be 5 V, whereas the
load power-supply voltage being monitored (VCM) can be as high as 36 V. Note that the INA300 device can
withstand the full –0.3 V to +36 V range at the input terminals, regardless of whether the device has power
applied or not.
Power-supply bypass capacitors are required for stability and must be placed as closely as possible to the
supply and ground terminals of the device. A typical value for this supply bypass capacitor is 0.1 µF. Applications
with noisy or high-impedance power supplies may require additional decoupling capacitors to reject power-
supply noise.
Copyright © 2021 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
10 Layout
10.1 Layout Guidelines
• The power-supply bypass capacitor must be placed as closely as possible to the supply and ground
terminals. The recommended value of this bypass capacitor is 0.1 µF. Additional decoupling capacitance can
be added to compensate for noisy or high-impedance power supplies.
• The connection of RLIMIT to the ground terminal must be made as direct as possible to limit additional
capacitance on this node. Routing this connection must be limited to the same plane if possible avoiding vias
to internal planes. If the routing cannot be made on the same plane and must pass through vias, ensure that
a path is routed from the RLIMIT back to the ground terminal and that the RLIMIT is not connected directly to a
ground plane.
• The DELAY terminal must be either connected directly to ground, directly to supply, or left completely floating.
Additional external resistors must not be connected to this terminal. If a resistance is required by the
application to be placed in series with either the supply or ground connection to the DELAY terminal, this
resistance must be limited to 1 kΩso as to not conflict with the internal level detection circuitry.
• The HYS terminal must be either connected directly to ground, directly to supply, or left completely floating.
Additional external resistors must not be connected to this terminal. If a resistance is required by the
application to be placed in series with either the supply or ground connections to the HYS terminal, this
resistance must be limited to 1 kΩso as to not conflict with the internal level detection circuitry.
• The open-drain output pin is recommended to be pulled up to the supply voltage rail through a 10-kΩpull-up
resistor.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
10.2 Layout Example
VIA to Power or Ground Plane
VIA to Internal Layer
IN+
HYS
VS
Kelvin Connection
Supply Voltage
IN-
LIMIT
EN
GND
Supply Bypass
Capacitor
DELAY
LATCH
ALERT
Pull-Up Resistor
Limit Resistor
Alert Signal Trace
Digital Control Traces
NOTE: Connect the limit resistor directly to the GND terminal.
图10-1. Recommended Layout for WSON Package
Copyright © 2021 Texas Instruments Incorporated
30
Submit Document Feedback
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
VIA to Power or Ground Plane
VIA to Internal Layer
IN+
IN-
HYS
VS
Kelvin Connection
Supply Voltage
LIMIT
EN
GND
Supply Bypass
Capacitor
DELAY
LATCH
ALERT
Pull-Up Resistor
Limit Resistor
Alert Signal Trace
Digital Control Traces
NOTE: Connect the limit resistor directly to the GND terminal.
图10-2. Recommended Layout for VSSOP Package
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
31
Product Folder Links: INA300
INA300
www.ti.com.cn
ZHCSC46C –FEBRUARY 2014 –REVISED JUNE 2021
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
• INA300EVM User's Guide (SBAU220).
11.2 接收文档更新通知
要接收文档更新通知,请导航至 ti.com 上的器件产品文件夹。点击订阅更新 进行注册,即可每周接收产品信息更
改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
11.3 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料,可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范,并且不一定反映 TI 的观点;请参阅
TI 的《使用条款》。
11.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.6 术语表
TI 术语表
本术语表列出并解释了术语、首字母缩略词和定义。
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
32
Submit Document Feedback
Product Folder Links: INA300
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受TI 的销售条款(https:www.ti.com/legal/termsofsale.html) 或ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI
提供这些资源并不会扩展或以其他方式更改TI 针对TI 产品发布的适用的担保或担保免责声明。重要声明
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021,德州仪器(TI) 公司
PACKAGE OPTION ADDENDUM
www.ti.com
3-Nov-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
INA300AIDGSR
INA300AIDGST
INA300AIDSQR
INA300AIDSQT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
VSSOP
VSSOP
WSON
WSON
DGS
DGS
DSQ
DSQ
10
10
10
10
2500 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
NIPDAUAG | SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
-40 to 125
-40 to 125
12T6
12T6
SKD
SKD
Samples
Samples
Samples
Samples
NIPDAUAG | SN
NIPDAU
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
3-Nov-2022
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA300 :
Automotive : INA300-Q1
•
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Jun-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
INA300AIDGSR
INA300AIDGSR
INA300AIDGST
INA300AIDGST
INA300AIDSQR
INA300AIDSQT
VSSOP
VSSOP
VSSOP
VSSOP
WSON
WSON
DGS
DGS
DGS
DGS
DSQ
DSQ
10
10
10
10
10
10
2500
2500
250
330.0
330.0
330.0
330.0
180.0
180.0
12.4
12.4
12.4
12.4
8.4
5.3
5.3
5.3
5.3
2.3
2.3
3.4
3.4
3.4
3.4
2.3
2.3
1.4
1.4
8.0
8.0
8.0
8.0
4.0
4.0
12.0
12.0
12.0
12.0
8.0
Q1
Q1
Q1
Q1
Q2
Q2
1.4
250
1.4
3000
250
1.15
1.15
8.4
8.0
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Jun-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
INA300AIDGSR
INA300AIDGSR
INA300AIDGST
INA300AIDGST
INA300AIDSQR
INA300AIDSQT
VSSOP
VSSOP
VSSOP
VSSOP
WSON
WSON
DGS
DGS
DGS
DGS
DSQ
DSQ
10
10
10
10
10
10
2500
2500
250
364.0
366.0
366.0
364.0
210.0
210.0
364.0
364.0
364.0
364.0
185.0
185.0
27.0
50.0
50.0
27.0
35.0
35.0
250
3000
250
Pack Materials-Page 2
PACKAGE OUTLINE
DSQ0010A
WSON - 0.8 mm max height
S
C
A
L
E
5
.
0
0
0
PLASTIC SMALL OUTLINE - NO LEAD
2.1
1.9
A
B
PIN 1 INDEX AREA
2.1
1.9
0.8
0.7
C
SEATING PLANE
0.08 C
0.05
0.00
0.9 0.1
SYMM
EXPOSED
THERMAL PAD
(0.2) TYP
5
6
SYMM
1.5 0.1
11
2X 1.6
8X 0.4
1
PIN 1 ID
10
0.25
0.15
10X
0.4
0.2
10X
0.1
C A B
0.05
4218906/A 04/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
DSQ0010A
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
(0.9)
SEE SOLDER MASK
DETAIL
10X (0.5)
10X (0.2)
SYMM
10
1
(1.5)
8X (0.4)
11
SYMM
(0.5)
(R0.05) TYP
5
6
(
0.2) TYP
VIA
(1.9)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL UNDER
SOLDER MASK
METAL EDGE
EXPOSED METAL
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
SOLDER MASK DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4218906/A 04/2019
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
DSQ0010A
WSON - 0.8 mm max height
PLASTIC SMALL OUTLINE - NO LEAD
10X (0.5)
10X (0.2)
(0.85)
10
1
8X (0.4)
11
SYMM
(1.38)
(R0.05) TYP
5
6
SYMM
(1.9)
SOLDER PASTE EXAMPLE
BASED ON 0.125 MM THICK STENCIL
SCALE: 20X
EXPOSED PAD 11
87% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
4218906/A 04/2019
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
PACKAGE OUTLINE
DGS0010A
VSSOP - 1.1 mm max height
S
C
A
L
E
3
.
2
0
0
SMALL OUTLINE PACKAGE
C
SEATING PLANE
0.1 C
5.05
4.75
TYP
PIN 1 ID
AREA
A
8X 0.5
10
1
3.1
2.9
NOTE 3
2X
2
5
6
0.27
0.17
10X
3.1
2.9
1.1 MAX
0.1
C A
B
B
NOTE 4
0.23
0.13
TYP
SEE DETAIL A
0.25
GAGE PLANE
0.15
0.05
0.7
0.4
0 - 8
DETAIL A
TYPICAL
4221984/A 05/2015
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-187, variation BA.
www.ti.com
EXAMPLE BOARD LAYOUT
DGS0010A
VSSOP - 1.1 mm max height
SMALL OUTLINE PACKAGE
10X (1.45)
(R0.05)
TYP
SYMM
10X (0.3)
1
5
10
SYMM
6
8X (0.5)
(4.4)
LAND PATTERN EXAMPLE
SCALE:10X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
NOT TO SCALE
4221984/A 05/2015
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DGS0010A
VSSOP - 1.1 mm max height
SMALL OUTLINE PACKAGE
10X (1.45)
SYMM
(R0.05) TYP
10X (0.3)
8X (0.5)
1
5
10
SYMM
6
(4.4)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:10X
4221984/A 05/2015
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明