INA302A1QPWRQ1 [TI]
具有双比较器的 AEC-Q100、36V、双向、550kHz、4V/µs 高精度电流感应放大器 | PW | 14 | -40 to 125;型号: | INA302A1QPWRQ1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有双比较器的 AEC-Q100、36V、双向、550kHz、4V/µs 高精度电流感应放大器 | PW | 14 | -40 to 125 放大器 比较器 |
文件: | 总39页 (文件大小:1846K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
具有两个窗口比较器的INA30x-Q1 符合AEC-Q100 标准的36V、双向、
550kHz、4V/µs、高精度电流感应放大器
1 特性
3 说明
• 符合面向汽车应用的AEC-Q100 标准
INA302-Q1 和 INA303-Q1 (INA30x-Q1) 器件具有一个
高共模、双向、电流感应放大器和两个高速比较器,用
于检测超出范围的电流状况。INA302-Q1 比较器配置
为检测和响应过流状况。INA303-Q1 比较器在窗口配
置中配置为响应过流和欠流状况。这些器件使用外部限
位设置电阻器,对每个比较器设置都具有可调限位阈值
范围。这些电流分流监控器可在独立于电源的 –0.1V
至+36V 共模电压范围内测量差动电压信号。此外,这
些器件还将承受高达40V 的共模电压。
– 温度等级1:-40°C ≤TA ≤+125°C
– HBM ESD 分类等级2
– CDM ESD 分类等级C6
• 提供功能安全
– 可帮助进行功能安全系统设计的文档
• 宽共模输入范围:-0.1V 至+36V
• 两个比较器输出:
– INA302-Q1:两个独立的超限警报
– INA303-Q1:窗口比较器
– 阈值电平单独设置
开漏极警报输出可配置为在透明模式(输出状态与输入
状态保持一致)或锁存模式(警报输出在锁存复位时清
除)下运行。比较器1 的警报响应时间小于1µs,而比
较器 2 的警报响应时间通过外部电容器进行设置,范
围介于2µs 至10s 之间。
– 比较器1 警报响应:1µs
– 比较器2 可调延迟:2µs 至10s
– 具有独立锁存控制模式的开漏极输出
• 高准确度放大器:
这些器件由单个 2.7V 至 5.5V 电源供电,消耗的最大
电源电流为 950μA。这些器件具有 –40°C 至
+125°C 的扩展额定工作温度范围,并且采用 14 引脚
TSSOP 封装。
– 失调电压:30µV(最大值,A3 版本)
– 失调电压漂移:0.5µV/°C(最大值)
– 增益误差:0.15%(最大值,A3 版本)
– 增益误差漂移:10ppm/°C
• 可用放大器增益:
器件信息
– INA302A1-Q1,INA303A1-Q1:20V/V
– INA302A2-Q1,INA303A2-Q1:50V/V
– INA302A3-Q1,INA303A3-Q1:100V/V
封装尺寸(标称值)
器件型号
INA302-Q1
封装
TSSOP (14)
4.40mm × 5.00mm
INA303-Q1
2 应用
• 系统故障检测
• 电机控制和保护
• 泵控制和保护
• 直流/直流转换器
• 车身控制模块
2.7 V to 5.5 V
CBYPASS
0.1 …F
RPULL-UP
10 kꢀ
VS
INA30x-Q1
RLIMIT1
LIMIT1
COMP1
Microcontroller
Supply
(0 V to 36 V)
+
ALERT1
LATCH1
GPIO
GPIO
IN+
+
OUT
ADC
COMP2
IN-
(
)
+
-
ALERT2
LATCH2
GPIO
GPIO
Load
(
)
-
+
DELAY
LIMIT2
CDELAY
GND
RLIMIT2
Reference Voltage
典型应用
本文档旨在为方便起见,提供有关TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SBOS977
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
Table of Contents
8 Application and Implementation..................................23
8.1 Application Information............................................. 23
8.2 Typical Application.................................................... 29
9 Power Supply Recommendations................................31
10 Layout...........................................................................32
10.1 Layout Guidelines................................................... 32
10.2 Layout Example...................................................... 32
11 Device and Documentation Support..........................33
11.1 Documentation Support.......................................... 33
11.2 接收文档更新通知................................................... 33
11.3 支持资源..................................................................33
11.4 Related Links.......................................................... 33
11.5 Trademarks............................................................. 33
11.6 Electrostatic Discharge Caution..............................33
11.7 术语表..................................................................... 33
12 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings........................................ 4
6.2 ESD Ratings............................................................... 4
6.3 Recommended Operating Conditions.........................4
6.4 Thermal Information....................................................4
6.5 Electrical Characteristics.............................................5
6.6 Typical Characteristics................................................7
7 Detailed Description......................................................14
7.1 Overview...................................................................14
7.2 Functional Block Diagram.........................................14
7.3 Feature Description...................................................15
7.4 Device Functional Modes..........................................21
Information.................................................................... 33
4 Revision History
Changes from Revision * (March 2019) to Revision A (May 2021)
Page
• 更新了整个文档中的表格、图和交叉参考的编号格式.........................................................................................1
• 添加了“功能安全”要点.................................................................................................................................... 1
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
5 Pin Configuration and Functions
VS
OUT
1
14
13
12
11
10
9
IN+
2
3
4
5
6
7
INœ
LIMIT1
REF
ALERT1
ALERT2
DELAY
LIMIT2
NC
GND
LATCH1
LATCH2
8
Not to scale
图5-1. PW Package 14-Pin TSSOP Top View
表5-1. Pin Functions
PIN
TYPE
DESCRIPTION
NO.
NAME
VS
1
2
Analog
Power supply, 2.7 V to 5.5 V
Output voltage
OUT
Analog output
ALERT1 threshold limit input; see the Setting Alert Thresholds section for details on
setting the limit threshold
3
LIMIT1
Analog input
4
5
6
7
8
REF
Analog input
Analog
Reference voltage, 0 V to VS
Ground
GND
LATCH1
LATCH2
NC
Digital input
Digital input
—
Transparent or latch mode selection input
Transparent or latch mode selection input
No internal connection
ALERT2 threshold limit input; see the Setting Alert Thresholds section for details on
setting the limit threshold
9
LIMIT2
DELAY
ALERT2
Analog input
Analog input
Analog output
Delay timing input; see the Alert Outputs section for details on setting the delayed
alert response for comparator 2
10
11
Open-drain output; active-low. This pin is an overlimit alert for the INA302-Q1 and an
underlimit alert for the INA303-Q1.
12
13
14
ALERT1
IN–
Analog output
Analog input
Analog input
Open-drain output, active-low overlimit alert
Connect to load side of the current-sensing resistor
Connect to supply side of the current-sensing resistor
IN+
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
UNIT
VS
Supply voltage
6
40
V
(2)
Differential (VIN+) –(VIN–
)
–40
GND –0.3
GND –0.3
GND –0.3
GND –0.3
GND –0.3
V
Analog inputs (IN+, IN–)
Common-mode(3)
40
Analog input
LIMIT1, LIMIT2, DELAY, REF
OUT
(VS) + 0.3
(VS) + 0.3
(VS) + 0.3
6
V
V
Analog output
Digital input
LATCH1, LATCH2
ALERT1, ALERT2
V
Digital output
V
TJ
Junction temperature
Storage temperature
150
°C
°C
Tstg
150
–65
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
(2) VIN+ and VIN– are the voltages at the IN+ and IN–pins, respectively.
(3) Input voltage can exceed the voltage shown without causing damage to the device if the current at that pin is limited to 5 mA.
6.2 ESD Ratings
VALUE
±3000
±1500
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
V(ESD)
Electrostatic discharge
V
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
–0.1
2.7
NOM
12
MAX
36
UNIT
VCM
VS
Common-mode input voltage
Operating supply voltage
V
V
5
5.5
TA
Operating free-air temperature
125
°C
–40
6.4 Thermal Information
INA30x-Q1
THERMAL METRIC(1)
PW (TSSOP)
14 PINS
110.2
35.1
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
53.2
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
2.3
ψJT
52.4
ψJB
RθJC(bot)
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6.5 Electrical Characteristics
at TA = 25°C, VSENSE = 0 V, VREF = VS / 2, VS = 5 V, VIN+ = 12 V, VLIMIT1 = 3 V, and VLIMIT2 = 3 V (INA302-Q1) or 2 V
(INA303-Q1) (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUT
VIN = VIN+ –VIN–, VREF = VS / 2,
A1 versions
0
0
±125
±50
VIN = VIN+ –VIN–, VREF = VS / 2,
A2 versions
VIN
Differential input voltage range
mV
VIN = VIN+ –VIN–, VREF = VS / 2,
A3 versions
0
±25
VIN+ = 0 V to 36 V,
TA = –40°C to +125°C, A1 versions
100
106
110
114
118
120
VIN+ = 0 V to 36 V, TA = –40°C to
+125°C, A2 versions
CMRR
Common-mode rejection ratio
Offset voltage, RTI(1)
dB
µV
VIN+ = 0 V to 36 V,
TA = –40°C to +125°C, A3 versions
A1 versions
±15
±10
±5
±80
±50
±30
0.25
VOS
A2 versions
A3 versions
dVOS/dT
PSRR
Offset voltage drift, RTI(1)
0.02
µV/°C
µV/V
TA= –40°C to +125°C
VS = 2.7 V to 5.5 V, VIN+ = 12 V,
TA = –40°C to +125°C
Power-supply rejection ratio
±0.3
±5
IB
Input bias current
Input offset current
IB+, IB–
115
µA
µA
IOS
VSENSE = 0 mV
±0.01
OUTPUT
A1 versions
20
50
G
Gain
A2 versions
V/V
A3 versions
100
±0.02%
±0.05%
±0.1%
3
±0.075%
±0.1%
±0.15%
10
VOUT = 0.5 V to VS –0.5 V, A1 versions
VOUT = 0.5 V to VS –0.5 V, A2 versions
VOUT = 0.5 V to VS –0.5 V, A3 versions
TA= –40°C to +125°C
Gain error
ppm/°C
pF
Nonlinearity error
±0.01%
500
VOUT = 0.5 V to VS –0.5 V
No sustained oscillation
Maximum capacitive load
VOLTAGE OUTPUT
Swing to VS power-supply rail
RL = 10 kΩto GND,
TA = –40°C to +125°C
V
VS –0.05
VS –0.1
RL = 10 kΩto GND,
TA = –40°C to +125°C
Swing to GND
VGND + 15
VGND + 30
mV
FREQUENCY RESPONSE
A1 versions, COUT = 500 pF
A2 versions, COUT = 500 pF
A3 versions, COUT = 500 pF
550
440
400
4
BW
Bandwidth
kHz
V/µs
SR
Slew rate
NOISE, RTI(1)
Voltage noise density
30
nV/√Hz
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
at TA = 25°C, VSENSE = 0 V, VREF = VS / 2, VS = 5 V, VIN+ = 12 V, VLIMIT1 = 3 V, and VLIMIT2 = 3 V (INA302-Q1) or 2 V
(INA303-Q1) (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMPARATOR
Comparator 1, input overdrive = 1 mV
0.6
1
2
tp
Total alert propagation delay
µs
Comparator 2, input overdrive = 1 mV,
delay = 100 kΩto VS
1.25
Comparator 1, VOUT step = 0.5 V to 4.5 V,
VLIMIT = 4 V
1
1.5
2.5
Comparator 2 (INA302-Q1),
VOUT step = 0.5 V to 4.5 V, VLIMIT = 4 V,
delay = 100 kΩto VS
1.5
Slew-rate-limited tp
µs
Comparator 2 (INA303-Q1),
VOUT step = 4.5 V to 0.5 V, VLIMIT = 1 V,
delay = 100 kΩto VS
1.5
80
2.5
79.2
78.4
79.7
79.2
80.8
81.6
80.4
80.8
TA = 25°C, VLIMIT1 < VS –0.6 V
Limit threshold output current,
comparator 1
ILIMIT1
µA
µA
TA = –40°C to +125°C,
VLIMIT1 < VS –0.6 V
80
TA = 25°C, VLIMIT2 < VS –0.6 V
Limit threshold output current,
comparator 2
ILIMIT2
TA = –40°C to +125°C,
VLIMIT2 < VS –0.6 V
A1 versions
0.5
0.5
3.5
3.5
4.0
VOS
Offset voltage, both comparators
A2 versions
mV
mV
A3 versions
0.5
HYS
Hysteresis
comparator 1, comparator 2
TA = –40°C to +125°C
TA = –40°C to +125°C
TA = –40°C to +125°C, VDELAY = 0.6 V
100
Internal programmable delay error
Delay threshold voltage
4%
1.23
5.15
V
VTH
ID
1.21
4.85
1.22
5
µA
Delay charging current
RD
VIH
VIL
VOL
Delay discharge resistance
LATCH1, LATCH2 high-level input voltage
LATCH1, LATCH2 low-level input voltage
Alert low-level output voltage
70
Ω
1.4
0
6
0.4
V
TA = –40°C to +125°C
V
TA = –40°C to +125°C
70
400
mV
IOL = 3 mA, TA = –40°C to +125°C
ALERT1, ALERT2 pin leakage input
current
VOH = 3.3 V
0.1
1
µA
µA
LATCH1, LATCH2 digital leakage input
current
1
0 V ≤VLATCH1 , VLATCH2 ≤VS
POWER SUPPLY
TA = 25°C
850
950
IQ
Quiescent current
µA
1150
TA = –40°C to +125°C
(1) RTI = referred-to-input.
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6.6 Typical Characteristics
at TA = 25°C, VREF = VS / 2, VSENSE = 0 V, VS = 5 V, VIN+ = 12 V, and ALERT1, ALERT2 pullup resistors = 10 kΩ(unless
otherwise noted)
Input Offset Voltage (mV)
Input Offset Voltage (mV)
图6-1. Input Offset Voltage Distribution (INA30xA1-Q1)
图6-2. Input Offset Voltage Distribution (INA30xA2-Q1)
20
INA30xA1-Q1
INA30xA2-Q1
INA30xA3-Q1
15
10
5
0
-5
-10
-15
-20
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
D004
Input Offset Voltage (mV)
图6-4. Input Offset Voltage vs. Temperature
图6-3. Input Offset Voltage Distribution (INA30xA3-Q1)
Common-Mode Rejection Ratio (mV/V)
Common-Mode Rejection Ratio (mV/V)
图6-5. CMRR Distribution (INA30xA1-Q1)
图6-6. CMRR Distribution (INA30xA2-Q1)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6.6 Typical Characteristics (continued)
at TA = 25°C, VREF = VS / 2, VSENSE = 0 V, VS = 5 V, VIN+ = 12 V, and ALERT1, ALERT2 pullup resistors = 10 kΩ(unless
otherwise noted)
0
-0.2
-0.4
-0.6
-0.8
-1
-1.2
-1.4
-1.6
INA30xA1-Q1
INA30xA2-Q1
-1.8
INA30xA3-Q1
-2
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
D008
Common-Mode Rejection Ratio (mV/V)
图6-8. CMRR vs. Temperature
图6-7. CMRR Distribution (INA30xA3-Q1)
140
120
100
80
INA30xA1-Q1
INA30xA2-Q1
INA30xA3-Q1
60
40
10
100
1000 10000
Frequency (Hz)
100000
1000000
D009
Gain Error (%)
图6-9. CMRR vs. Frequency
图6-10. Gain Error Distribution (INA30xA1-Q1)
Gain Error (%)
Gain Error (%)
图6-11. Gain Error Distribution (INA30xA2-Q1)
图6-12. Gain Error Distribution (INA30xA3-Q1)
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6.6 Typical Characteristics (continued)
at TA = 25°C, VREF = VS / 2, VSENSE = 0 V, VS = 5 V, VIN+ = 12 V, and ALERT1, ALERT2 pullup resistors = 10 kΩ(unless
otherwise noted)
0.5
0.4
0.3
0.2
0.1
0
50
40
30
20
10
0
INA30xA1-Q1
INA30xA2-Q1
INA30xA3-Q1
-0.1
-0.2
-0.3
-0.4
-0.5
INA30xA1-Q1
INA30xA2-Q1
INA30xA3-Q1
-10
-20
-50
-25
0
25
50
75
100
125
150
10
100
1k
10k 100k
Frequency (Hz)
1m
10m
Temperature (èC)
D013
D014
图6-13. Gain Error vs. Temperature
图6-14. Gain vs. Frequency
140
VS
120
100
80
V
S - 1
VS - 2
GND + 3
GND + 2
GND + 1
GND
60
125ºC
25ºC
-40ºC
40
0
2
4
6
8
10
12
14
20
Output Current (mA)
1
10
100
1k 10k
Frequency (Hz)
100k
1M
10M
图6-16. Output Voltage Swing vs. Output Current
图6-15. PSRR vs. Frequency
225
200
175
150
125
100
75
150
125
100
75
50
50
25
25
0
0
-25
-25
-5
0
5
10
Common-Mode Voltage (V)
15
20
25
30
35
40
-5
0
5
10
Common-Mode Voltage (V)
15
20
25
30
35
40
VS = 5 V
VS = 0 V
图6-17. Input Bias Current vs. Common-Mode Voltage
图6-18. Input Bias Current vs. Common-Mode Voltage
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6.6 Typical Characteristics (continued)
at TA = 25°C, VREF = VS / 2, VSENSE = 0 V, VS = 5 V, VIN+ = 12 V, and ALERT1, ALERT2 pullup resistors = 10 kΩ(unless
otherwise noted)
145
140
135
130
125
120
115
110
105
100
1000
950
900
850
800
750
700
650
600
-50
-25
0
25
50
75
100
125
150
2.7
3
3.3 3.6 3.9 4.2 4.5 4.8 5.1 5.4 5.7
Supply Voltage (V)
Temperature (èC)
图6-19. Input Bias Current vs. Temperature
图6-20. Quiescent Current vs. Supply Voltage
1000
1050
1000
950
900
850
800
750
700
700
500
300
200
100
70
50
30
20
10
1000 2000 5000 10000
100000
1000000
-50
-25
0
25
50
75
100
125
150
Frequency (Hz)
Temperature (èC)
图6-22. Input-Referred Voltage Noise vs. Frequency
图6-21. Quiescent Current vs. Temperature
Input
Output
Time (1 s/div)
Time (1 ms/div)
.
4-VPP output step
图6-23. 0.1-Hz to 10-Hz Voltage Noise (Referred to Input)
图6-24. Voltage Output Rising Step Response
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6.6 Typical Characteristics (continued)
at TA = 25°C, VREF = VS / 2, VSENSE = 0 V, VS = 5 V, VIN+ = 12 V, and ALERT1, ALERT2 pullup resistors = 10 kΩ(unless
otherwise noted)
Input
Output
VCM
VOUT
Time (1 ms/div)
Time (5ms/div)
4-VPP output step
.
图6-26. Common-Mode Voltage Transient Response
图6-25. Voltage Output Falling Step Response
80.8
80.6
80.4
80.2
80
79.8
79.6
79.4
79.2
VSUPPLY
VOUT
Time (5 ms/div)
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
.
图6-28. LIMIT1 Current Source vs. Temperature
图6-27. Start-Up Response
80.8
80.6
80.4
80.2
80
5.3
5.2
5.1
5
79.8
79.6
79.4
79.2
4.9
4.8
4.7
-50
-25
0
25
50
75
100
125
150
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
Temperature (èC)
图6-29. LIMIT2 Current Source vs. Temperature
图6-30. DELAY Current vs. Temperature
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6.6 Typical Characteristics (continued)
at TA = 25°C, VREF = VS / 2, VSENSE = 0 V, VS = 5 V, VIN+ = 12 V, and ALERT1, ALERT2 pullup resistors = 10 kΩ(unless
otherwise noted)
9.5
8.5
7.5
6.5
5.5
4.5
3.5
2.5
1.5
0.5
-0.5
0.5
0.4
0.3
0.2
0.1
0
VOUT
VLIMIT2
ALERT2
VSENSE
VOUT
VLIMIT1
ALERT1
VSENSE
-0.1
-0.2
-0.3
-0.4
-0.5
-5E-7
7E-7
1.9E-6 3.1E-6
Time (200 ns/div)
4.3E-6
5.5E-6
Time (600 ns/div)
D031
DELAY = open
图6-32. Comparator 2 Total Propagation Delay (INA303-Q1)
.
图6-31. Comparator 1 Total Propagation Delay (INA30x-Q1)
VOUT
VLIMIT2
ALERT2
VSENSE
VOUT
VLIMIT2
ALERT2
VSENSE
Time (600 ns/div)
Time (600 ns/div)
DELAY = open
DELAY = 100 kΩto VS
图6-33. Comparator 2 Total Propagation Delay (INA303-Q1)
图6-34. Comparator 2 Total Propagation Delay (INA302-Q1)
1000
VOUT
VLIMIT2
ALERT2
VSENSE
800
600
400
200
0
Time (600 ns/div)
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
.
VOD = 1 mV
DELAY = 100 kΩto VS
图6-36. Comparator 1 Propagation Delay vs. Temperature
图6-35. Comparator 2 Total Propagation Delay (INA302-Q1)
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
6.6 Typical Characteristics (continued)
at TA = 25°C, VREF = VS / 2, VSENSE = 0 V, VS = 5 V, VIN+ = 12 V, and ALERT1, ALERT2 pullup resistors = 10 kΩ(unless
otherwise noted)
2200
2000
1800
1600
1400
1200
110
100
90
80
70
60
50
40
30
20
10
0
ALERT1 VOL
ALERT2 VOL
0
0.5
1
1.5
2
2.5
3
3.5
Low-Level Output Current (mA)
4
4.5
5
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
.
VOD = 1 mV
图6-38. Comparator Alert VOL vs. IOL
图6-37. Comparator 2 Propagation Delay vs. Temperature
120
120
100
80
100
80
60
40
20
0
60
40
INA30xA1-Q1
INA30xA2-Q1
INA30xA3-Q1
INA30xA1-Q1
INA30xA2-Q1
INA30xA3-Q1
20
0
-50
-25
0
25
50
75
100
125
150
-50
-25
0
25
50
75
100
125
150
Temperature (èC)
Temperature (èC)
D039
D040
图6-39. Comparator 1 Hysteresis vs. Temperature
图6-40. Comparator 2 Hysteresis vs. Temperature
1000
LATCH1, LATCH2
ALERT1, ALERT2
A1
A2
A3
A4
500
200
100
50
20
10
5
2
1
0.5
0.2
0.1
10
100
1k
10k
Frequency (Hz)
100k
1M
10M
Time (2 ms/div)
D033
.
图6-42. Output Impedance vs. Frequency
图6-41. Comparator Latch Response
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
7 Detailed Description
7.1 Overview
The INA30x-Q1 feature a zero-drift, 36-V, common-mode, bidirectional, current-sensing amplifier, and two high-
speed comparators that can detect multiple out-of-range current conditions. These specially designed, current-
sensing amplifiers can be used in both low-side or high-side applications where common-mode voltages far
exceed the supply voltage of the device. Currents are measured by accurately sensing voltages developed
across current-sensing resistors (also known as current-shunt resistors). Current can be measured on input
voltage rails as high as 36 V, and the device can be powered from supply voltages as low as 2.7 V.
The zero-drift topology enables high-precision measurements with maximum input offset voltages as low as
30 μV (max) with a temperature contribution of only 0.25 μV/°C (max) over the full temperature range of –
40°C to +125°C. The low total offset voltage of the INA302-Q1 enables smaller current-sense resistor values to
be used, improving power-efficiency without sacrificing measurement accuracy resulting from the smaller input
signal.
Both devices use a single external resistor to set each out-of-range threshold. The INA302-Q1 allows for two
overcurrent thresholds, and the INA303-Q1 allows for both an undercurrent and overcurrent threshold. The
response time of the ALERT1 threshold is fixed and is less than 1 μs. The response time of the ALERT2
threshold can be set with an external capacitor. The combination of a precision current-sense amplifier with
onboard comparators creates a highly-accurate solution that is capable of fast detection of multiple out-of-range
conditions. The ability to detect when currents are out-of-range allows the system to take corrective actions to
prevent potential component or system-wide damage.
7.2 Functional Block Diagram
2.7 V to 5.5 V
CBYPASS
RLIMIT1
0.1 mF
LIMIT1
VS
INA30x-Q1
RPULL-UP1
10 kW
RPULL-UP2
10 kW
ILIMIT1
Power Supply
0 V to 36 V
+
-
ALERT1
LATCH1
IN+
IN-
+
OUT
Gain = 20,
50, 100
RSENSE
ILIMIT2
LATCH2
ALERT2
DELAY
+ (-)
- (+)
LOAD
REF
LIMIT2
GND
CDELAY
Reference Voltage
RLIMIT2
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
7.3 Feature Description
7.3.1 Bidirectional Current Sensing
The INA30x-Q1 sense current flow through a sense resistor in both directions. The bidirectional current-sensing
capability is achieved by applying a voltage at the REF pin to offset the output voltage. A positive differential
voltage sensed at the inputs results in an output voltage that is greater than the applied reference voltage.
Likewise, a negative differential voltage at the inputs results in output voltage that is less than the applied
reference voltage. The equation for the output voltage of the current-sense amplifier is shown in 方程式1.
VOUT = ILOADì RSENSE ìGAIN + V
REF
(1)
where
• ILOAD is the load current to be monitored.
• RSENSE is the current-sense resistor.
• GAIN is the gain option of the device selected.
• VREF is the voltage applied to the REF pin.
7.3.2 Out-of-Range Detection
The INA303-Q1 detects when negative currents are out-of-range by setting a voltage at the LIMIT2 pin that is
less than the applied reference voltage. The limit voltage is set with an external resistor or externally driven by a
voltage source or digital-to-analog converter (DAC); see the Setting Alert Thresholds section for additional
information. A typical application using the INA303-Q1 to detect negative overcurrent conditions is illustrated in
the Typical Application section.
7.3.3 Alert Outputs
Both ALERTx pins are active-low, open-drain outputs that pull low when the sensed current is detected to be out
of range. Both open-drain ALERTx pins require an external pullup resistor to an external supply. The external
supply for the pullup voltage can exceed the supply voltage, VS, but is restricted from operating at greater than
5.5 V. The pullup resistance is selected based on the capacitive load and required rise time; however, a 10-kΩ
resistor value is typically sufficient for most applications. The response time of the ALERT1 output to an out-of-
range event is less than 1 μs, and the response time of the ALERT2 output is proportional to the value of the
external CDELAY capacitor. The equation to calculate the delay time for the ALERT2 output is given in 方程式2:
If DELAY is connected to VS with 100 kW
1.5 ms
tDELAY
=
CDELAY ì VTH
If CDELAY > 47 pF
+ 2.5 ms
ID
(2)
where
• CDELAY is the external delay capacitor.
• VTH is the delay threshold voltage.
• ID is the DELAY pin current for comparator 2.
For example, if a delay time of 10 µs is desired, the calculated value for CDELAY is 30.7 pF. The closest standard
capacitor value to the calculated value is 30 pF. If a delay time greater than 2.5 µs on the ALERT2 output is not
needed, the CDELAY capacitor can be omitted. To achieve minimum delay on the ALERT2 output, connect a 100-
kΩ resistor from the DELAY pin to the VS pin. Both comparators in the INA30x-Q1 have hysteresis to avoid
oscillations in the ALERTx outputs. The effect hysteresis has on the comparator behavior is described in the
Hysteresis section.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
图 7-1 shows the alert output response of the internal comparators for the INA302-Q1. When the output voltage
of the current-sense amplifier is less than the voltage developed on either limit pin, both ALERTx outputs are in
the default high state. When the current sense amplifier output is greater than the threshold voltage set by the
LIMIT2 pin, the ALERT2 output pulls low after a delay time set by the external delay capacitor. The lower
overcurrent threshold is commonly referred to as the overcurrent warning threshold. If the current continues to
rise until the current-sense amplifier output voltage exceeds the threshold voltage set at the LIMIT1 pin, then the
ALERT1 output becomes active and immediately pulls low. The low voltage on ALERT1 indicates that the
measured signal at the amplifier input has exceeded the programmed threshold level, indicating an overcurrent
condition has occurred. The upper threshold is commonly referred to as the fault or system critical threshold.
Systems often initiate protection procedures (such as a system shutdown) when the current exceeds this
threshold.
Power Supply
0 V to 36 V
2.7 V to 5.5 V
Fault/Critical Threshold
Supply
INA302-Q1
VS
Warning Threshold
INPUT SIGNAL
RPULL-UP1
ALERT1
LIMIT1
RLIMIT1
LATCH1
IN+
+
VLIMIT1
OUT
RSENSE
Supply
IN-
VLIMIT2
RPULL-UP2
VOUT
ALERT2
LIMIT2
DELAY
Load
RLIMIT2
ALERT1
ALERT2
CDELAY
LATCH2
REF
GND
GND
tDELAY
图7-1. Out-of-Range Alert Responses for the INA302-Q1
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
图7-2 shows the alert output response of the internal comparators for the INA303-Q1. Both ALERTx outputs are
in the default high state when the output voltage of the current-sense amplifier is less than the voltage developed
at the LIMIT1 pin and is greater than the voltage developed at the LIMIT2 pin. The ALERT1 output becomes
active and pulls low when the current-sense amplifier output voltage exceeds the threshold voltage set at the
LIMIT1 pin. The low voltage on ALERT1 indicates that the measured signal at the amplifier input has exceeded
the programmed threshold level, indicating an overcurrent or out-of-range condition has occurred. When the
current-sense amplifier output is less than the threshold voltage set by the LIMIT2 pin, the ALERT2 output pulls
low after the delay time set by the external delay capacitor expires. The delay time for the ALERT2 output is
proportional to the value of the external CDELAY capacitor, and is calculated by 方程式2.
Power Supply
Overcurrent
0 V to 36 V
2.7 V to 5.5 V
Threshold
Supply
INA303-Q1
VS
Undercurrent
Threshold
RPULL-UP1
Input Signal
ALERT1
LIMIT1
RLIMIT1
LATCH1
IN+
+
VLIMIT1
VOUT
OUT
RSENSE
Supply
IN-
VLIMIT2
RPULL-UP2
ALERT2
LIMIT2
DELAY
ALERT1
ALERT2
RLIMIT2
Load
CDELAY
LATCH2
REF
GND
tDELAY
图7-2. Out-of-Range Alert Responses for the INA303-Q1
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
图 7-3 shows the alert output response of the INA303-Q1 when the two ALERTx pins are connected together.
When configured in this manner, the INA303-Q1 can provide a single signal to indicate when the sensed current
is operating either outside the normal operating bands or within a normal operational window. Both ALERT1 and
ALERT2 outputs behave the same in regard to the alert mode. The difference with ALERT2 is that the transition
of the output state is delayed by the time set by the external delay capacitor. If the overcurrent or undercurrent
event is not present when the delay time expires, ALERT2 does not respond.
Power Supply
0 V to 36 V
2.7 V to 5.5 V
Supply
Normal Operating Region
VS
INA303-Q1
RPULL-UP
INPUT SIGNAL
ALERT1
LIMIT1
ALERT
RLIMIT1
LATCH1
IN+
+
OUT
VLIMIT1
VOUT
RSENSE
Normal Operating
Region
IN-
VLIMIT2
ALERT2
LIMIT2
DELAY
Load
RLIMIT2
ALERT
LATCH2
GND
图7-3. Current Window Comparator Implementation With the INA303-Q1
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
7.3.3.1 Setting Alert Thresholds
The INA30x-Q1 family of devices determines if an out-of-range event is present by comparing the amplifier
output voltage to the voltage at the corresponding LIMITx pin. The threshold voltage for the LIMITx pins can be
set using a single external resistor or by connecting an external voltage source to each pin. The INA302-Q1
allows setting limits for two overcurrent conditions. Generally, the lower overcurrent threshold is referred to as a
warning limit and the higher overcurrent threshold is referred to as the critical or fault limit. The INA303-Q1
allows setting thresholds to detect both undercurrent and overcurrent limit conditions.
7.3.3.1.1 Resistor-Controlled Current Limit
The typical approach to set the limit threshold voltage is to connect resistors from the two LIMITx pins to ground.
The voltage developed across the RLIMIT1, RLIMIT2 resistors represents the desired fault current value at which
the corresponding ALERTx pin becomes active. The values for the RLIMIT1, RLIMIT2 resistors are calculated using
方程式3:
I
TRIP ì RSENSE ìGAIN + V
(
)
REF
RLIMIT
=
ILIMIT
(3)
where
• ITRIP is the desired out-of-range current threshold.
• RSENSE is the current-sensing resistor.
• GAIN is the gain option of the device selected.
• VREF is the voltage applied to the REF pin.
• ILIMIT is the limit threshold output current for the selected comparator, typically 80 µA.
Note
When solving for the value of RLIMIT, the voltage at the corresponding LIMITx pin as determined by the
product of RLIMIT and ILIMIT must not exceed the compliance voltage of VS –0.6 V.
7.3.3.1.1.1 Resistor-Controlled Current Limit: Example
For example, if the current level indicating an out-of-range condition (ITRIP) is 20 A and the current-sense resistor
value (RSENSE) is 10 mΩ, then the input threshold signal is 200 mV. The INA302A1-Q1 has a gain of 20, so the
resulting output voltage at the 20-A input condition is 4 V at the output of the current-sense amplifier when the
REF pin is grounded. The value for RLIMIT is selected to allow the device to detect this 20-A threshold, indicating
that an overcurrent event has occurred. When the INA302-Q1 detects this out-of-range condition, the ALERTx
pin asserts and pulls low. For this example, the value of RLIMIT to detect a 4-V level is calculated to be 50 kΩ.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
7.3.3.1.2 Voltage-Source-Controlled Current Limit
The second method for setting the out-of-range threshold is to directly drive the LIMITx pins with a
programmable DAC or other external voltage source. The benefit of this method is the ability to adjust the
current-limit threshold to account for different threshold voltages used for different system operating conditions.
For example, this method can be used in a system with one current-limit threshold level that must be monitored
during a power-up sequence, but different threshold levels must be monitored during other system operating
modes.
The voltage applied at the LIMITx pins sets the threshold voltage for out-of-range detection. The value of the
voltage for a given desired current trip point is calculated using 方程式4:
VSOURCE = ITRIP ì RSENSE ìGAIN + V
REF
(4)
where
• ITRIP is the desired out-of-range current threshold.
• RSENSE is the current-sensing resistor.
• GAIN is the gain option of the device selected.
• VREF is the voltage applied to the REF pin.
Note
The maximum voltage that can be applied to the LIMIT2 pin is VS – 0.6 V and the maximum voltage
that can be applied to the LIMIT1 pin must not exceed VS.
7.3.3.2 Hysteresis
The hysteresis included in the comparators of the INA30x-Q1 reduces the possibility of oscillations in the alert
outputs when the measured signal level is near the overlimit threshold level. For overrange events, the
corresponding ALERTx pin is asserted when the output voltage (VOUT) exceeds the threshold set at either
LIMITx pin. The output voltage must drop to less than the LIMITx pin threshold voltage by the hysteresis value in
order for the ALERTx pin to deassert and return to the nominal high state. Likewise for underrange events, the
corresponding ALERTx pin is also pulled low when the output voltage drops to less than the threshold set by
either LIMITx pin. The ALERTx pin is released when the output voltage of the current-sense amplifier rises to
greater than the set threshold plus hysteresis. Hysteresis functionality for both overrange and underrange events
is shown in 图7-4 and 图7-5 for the INA302-Q1 and INA303-Q1, respectively.
Overcurrent Threshold
Critical Threshold
VLIMIT1
VLIMIT1
VLIMIT1 - VHYS
VLIMIT1 - VHYS
Warning Threshold
VLIMIT2
VLIMIT2 - VHYS
VOUT
VOUT
VLIMIT2 + VHYS
VLIMIT2
Undercurrent
Threshold
ALERT1
ALERT1
ALERT2
ALERT2
图7-5. Comparator Hysteresis Behavior (INA303-
图7-4. Comparator Hysteresis Behavior (INA302-
Q1)
Q1)
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
7.4 Device Functional Modes
7.4.1 Alert Operating Modes
Each comparator has two output operating modes: transparent and latched. These modes determine how the
ALERTx pins respond when an out-of-range condition is removed. The device is placed into either transparent or
latched state based on the voltage applied to the corresponding LATCHx pin, as shown in 表7-1.
表7-1. Output Mode Settings
OUTPUT MODE
ALERTx transparent mode
ALERTx latch mode
LATCHx PINS SETTINGS
LATCHx = low
LATCHx = high
7.4.1.1 Transparent Output Mode
The comparators are set to transparent output mode when the corresponding LATCHx pin is pulled low. When
set to transparent mode, the output of the comparators changes and follows the input signal with respect to the
programmed alert threshold. For example, when the amplifier output violates the set limit value, the ALERTx
output pin is pulled low. As soon as the differential input signal drops to less than the alert threshold, the output
returns to the default high output state. A common implementation using the device in transparent mode is to
connect the ALERTx pins to a hardware interrupt input on a microcontroller. The ALERTx pin is pulled low as
soon as an out-of-range condition is detected, thus notifying the microcontroller. The microcontroller immediately
reacts to the alert and takes action to address the overcurrent condition. In transparent output mode, there is no
need to latch the state of the alert output because the microcontroller responds as soon as the out-of-range
condition occurs.
7.4.1.2 Latch Output Mode
The comparators are set to latch output mode when the corresponding LATCHx pin is pulled high. Some
applications do not continuously monitor the state of the ALERTx pins as described in the Transparent Output
Mode section. For example, if the device is set to transparent output mode in an application that only polls the
state of the ALERTx pins periodically, then the transition of the ALERTx pins can be missed when the out-of-
range condition is not present during one of these periodic polling events. Latch output mode allows the output
of the comparators to latch the output of the range condition so that the transition of the ALERTx pins is not
missed when the status of the comparator ALERTx pins is polled.
The difference between latch mode and transparent mode is how the alert output responds when an overcurrent
condition is removed. In transparent mode (LATCH1, LATCH2 = low), when the differential input signal drops to
within normal operating range, the ALERTx pin returns to the default high setting to indicate that the overcurrent
event has ended.
In latch mode (LATCHx = high), when an out-of-range condition is detected and the corresponding ALERTx pin
is pulled low; the ALERTx pin does not return to the default high state when the out-of-range condition is
removed. In order to clear the alert, the corresponding LATCHx pin must be pulled low for at least 100 ns. Pulling
the LATCHx pins low allows the corresponding ALERTx pin to return to the default high level, provided the out-
of-range condition is no longer present. If the out-of-range condition is still present when the LATCHx pins are
pulled low, then the corresponding ALERTx pin remains low. The ALERTx pins can be cleared (reset to high) by
toggling the corresponding LATCHx pin when the alert condition is detected by the system controller.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
The latch and transparent modes are illustrated in 图7-6. As illustrated in this figure, at time t1, the current-sense
amplifier exceeds the limit threshold. During this time the LATCH1 pin is toggled with no affect to the ALERT1
output. The state of the LATCH1 pin only matters when the output of the current-sense amplifier returns to the
normal operating region, as shown at t2. At this time the LATCH1 pin is high and the overcurrent condition is
latched on the ALERT1 output. As shown in the time interval between t2 and t3, the latch condition is cleared
when the LATCHx pin is pulled low. At time t4, the LATCH1 pin is already pulled low when the amplifier output
drops below the limit threshold for the second time. The device is set to transparent mode at this point and the
ALERT1 pin is pulled back high as soon as the output of the current-sense amplifier drops below the alert
threshold.
VLIMIT1
VOUT
(VIN+ - VIN-) x GAIN
0 V
t1
t2
t3
t4
t5
Latch Mode
LATCH1
ALERT1
Transparent Mode
Alert Clears
Alert Does Not Clear
图7-6. Transparent vs. Latch Mode
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
8 Application and Implementation
Note
以下应用部分中的信息不属于TI 器件规格的范围,TI 不担保其准确性和完整性。TI 的客 户应负责确定
器件是否适用于其应用。客户应验证并测试其设计,以确保系统功能。
8.1 Application Information
8.1.1 Selecting a Current-Sensing Resistor (RSENSE
)
Selecting the value of this current-sensing resistor is based primarily on two factors: the required accuracy of the
current measurement and the allowable power dissipation across the current-sensing resistor. Larger voltages
developed across this resistor allow for more accurate measurements to be made. Amplifiers have fixed internal
errors that are largely dominated by the inherent input offset voltage. When the input signal decreases, these
fixed internal amplifier errors become a larger portion of the measurement and increase the uncertainty in the
measurement accuracy. When the input signal increases, the measurement uncertainty is reduced because the
fixed errors are a smaller percentage of the signal being measured. Therefore, the use of larger-value, current-
sensing resistors inherently improves measurement accuracy.
However, a system design trade-off must be evaluated through the use of larger input signals for improving
measurement accuracy. Increasing the current-sense resistor value results in an increase in power dissipation
across the current-sensing resistor. Increasing the value of the current-shunt resistor increases the differential
voltage developed across the resistor when current passes through the component. This increase in voltage
across the resistor increases the power that the resistor must be able to dissipate. Decreasing the value of the
current-shunt resistor value reduces the power dissipation requirements of the resistor, but increases the
measurement errors resulting from the decreased input signal. Selecting the optimal value for the shunt resistor
requires factoring both the accuracy requirement for the specific application and the allowable power dissipation
of this component.
An increasing number of very low ohmic-value resistors are becoming more widely available with values
reaching down to 200 µΩ or lower, with power dissipations of up to 5 W that enable large currents to be
accurately monitored with sensing resistors.
8.1.1.1 Selecting a Current-Sensing Resistor: Example
In this example, the trade-offs involved in selecting a current-sensing resistor are discussed. This example
requires 2.5% accuracy for detecting a 10-A overcurrent event where only 250 mW is allowed for the dissipation
across the current-sensing resistor at the full-scale current level. Although the maximum power dissipation is
defined as 250 mW, a lower dissipation is preferred to improve system efficiency. Some initial assumptions are
made that are used in this example: the limit-setting resistor (RLIMIT) is a 1% component, and the maximum
tolerance specification for the internal threshold setting current source (1%) is used. Given the total error budget
of 2.5%, up to 0.5% of error can be attributed to the measurement error of the device under these conditions.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
As shown in 表8-1, the maximum value calculated for the current-sensing resistor with these requirements is 2.5
mΩ. Although this value satisfies the maximum power dissipation requirement of 250 mW, headroom is
available from the 2.5% maximum total overcurrent detection error to reduce the value of the current-sensing
resistor and to further reduce power dissipation. Selecting a 1.5-mΩ, current-sensing resistor value offers a
good tradeoff for reducing the power dissipation in this scenario by approximately 40% and stays within the
accuracy region.
表8-1. Calculating the Current-Sensing Resistor, RSENSE
PARAMETER
EQUATION
VALUE
UNIT
DESIGN TARGETS
IMAX
Maximum current
10
A
PD_MAX
Maximum allowable power dissipation
Allowable current threshold accuracy
250
mW
2.5%
DEVICE PARAMETERS
VOS
Offset voltage
30
µV
EG
Gain error
0.15%
CALCULATIONS
RSENSE_MAX
VOS_ERROR
ERRORTOTAL
ERRORINITIAL
ERRORAVAILABLE
VOS_ERROR_MAX
VDIFF_MIN
2
Maximum allowable RSENSE
Initial offset voltage error
PD_MAX / IMAX
2.5
0.12%
0.19%
2%
mΩ
(VOS / (RSENSE_MAX × IMAX ) × 100
√(VOS_ERROR 2 + EG
)
2
Total measurement error
Initial threshold error
ILIMIT tolerance + RLIMIT tolerance
Maximum allowable measurement error
Maximum allowable offset error
Minimum differential voltage
Minimum sense resistor value
Lowest-possible power dissipation
1%
Maximum error –ERRORINITIAL
√(ERRORAVAILABLE 2 –EG
VOS / VOS_ERROR_MAX (1%)
VDIFF_MIN / IMAX
)
2
0.48%
6.3
mV
mΩ
mW
RSENSE_MIN
PD_MIN
0.63
63
2
RSENSE_MIN × IMAX
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
8.1.2 Input Filtering
The integrated comparators in the INA30x-Q1 are very accurate at detecting out-of-range events because of the
low offset voltage; however, noise present at the input of the current-sense amplifier and noise internal to the
device can make the offset appear larger than specified. The most obvious effect that external noise can have
on the operation of a comparator is to cause a false alert condition. If a comparator detects a large noise
transient coupled into the signal, the device can easily falsely interpret this transient as an overrange condition.
External filtering helps reduce the amount of noise that reaches the comparator and reduce the likelihood of a
false alert from occurring because of external noise. The trade-off to adding this noise filter is that the alert
response time is increased because the input signal and the noise are filtered. 图 8-1 shows the implementation
of an input filter for the device.
2.7 V to 5.5 V
CBYPASS
0.1 mF
RLIMIT1
LIMIT1
VS
RPULL-UP1
RPULL-UP2
10 kW
10 kW
ILIMIT1
Power Supply
0 V to 36 V
+
ALERT1
LATCH1
IN+
+
CFILTER
RFILTER
< 10 W
OUT
Gain = 20,
50, 100
RSENSE
ILIMIT2
IN-
LATCH2
ALERT2
DELAY
+
LOAD
CDELAY
REF
LIMIT2
GND
RLIMIT2
Reference Voltage
图8-1. Input Filter Implementation
Limiting the amount of input resistance used in this filter is important because this resistance can have a
significant effect on the input signal that reaches the device input pins by adversely affecting the gain error of the
device. A typical system implementation involves placing the current-sensing resistor very near the device so the
traces are very short and the trace impedance is very small. This layout helps reduce coupling of additional
noise into the measurement. Under these conditions, the characteristics of the input bias currents have minimal
effect on device performance.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
As shown in 图 8-2, the input bias currents increase in opposite directions when the differential input voltage
increases. This increase results from the design of the device that allows common-mode input voltages to far
exceed the device supply voltage range. When input filter resistors are placed in series with the unequal input
bias currents, unequal voltage drops are developed across the input resistors. The difference between these two
drops appears as an added signal that (in this case) subtracts from the voltage developed across the current-
sensing resistor, thus reducing the signal that reaches the device input pins. Smaller-value input resistors reduce
this effect of signal attenuation to allow for a more accurate measurement.
160
140
120
100
80
IB+
IB-
60
-125 -100 -75 -50 -25
0
25
50
Differential Input Voltage (mV)
75 100 125
图8-2. Input Bias Current vs Differential Input Voltage
The internal bias network present at the input pins shown in 图 8-3 is responsible for the mismatch in input bias
currents that is shown in 图 8-2. If additional external series filter resistors are added to the circuit, the mismatch
in bias currents results in a mismatch of voltage drops across the filter resistors. This mismatch creates a
differential error voltage that subtracts from the voltage developed at the shunt resistor. This error results in a
voltage at the device input pins that is different than the voltage developed across the shunt resistor. Without the
additional series resistance, the mismatch in input bias currents has little effect on device operation. The amount
of error these external filter resistors add to the measurement is calculated using 方程式 6, where the gain error
factor is calculated using 方程式5.
V+
VCM
RS < 10 W
RINT
VOUT
RSHUNT
Bias
CF
RS < 10 W
VREF
RINT
Load
Comparators omitted for simplicity.
图8-3. Filter at Input Pins
The amount of variance in the differential voltage present at the device input relative to the voltage developed at
the shunt resistor is based both on the external series resistance value as well as the internal input resistors, R3
and R4 (or RINT as illustrated in 图 8-3). The reduction of the shunt voltage reaching the device input pins
appears as a gain error when comparing the output voltage relative to the voltage across the shunt resistor. A
factor can be calculated to determine the amount of gain error that is introduced by the addition of external
Copyright © 2021 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
series resistance. The equation used to calculate the expected deviation from the shunt voltage to what is
measured at the device input pins is given in 方程式5:
(1250 ´ RINT
)
Gain Error Factor =
(1250 ´ RS) + (1250 ´ RINT) + (RS ´ RINT
)
(5)
where
• RINT is the internal input resistor (R3 and R4).
• RS is the external series resistance.
With the adjustment factor from 方程式 5, including the device internal input resistance, this factor varies with
each gain version, as shown in 表8-2. Each individual device gain error factor is shown in 表8-3.
表8-2. Input Resistance
PRODUCT
INA30xA1-Q1
INA30xA2-Q1
INA30xA3-Q1
GAIN
RINT (kΩ)
20
12.5
5
50
100
2.5
表8-3. Device Gain Error Factor
PRODUCT
SIMPLIFIED GAIN ERROR FACTOR
12,500
INA30xA1-Q1
11ìR +12,500
(
)
S
1000
INA30xA2-Q1
INA30xA3-Q1
RS +1000
2500
3ìR + 2500
(
)
S
The gain error that is expected from the addition of the external series resistors is then calculated based on 方程
式6:
Gain Error (%) = 100 - (100 ´ Gain Error Factor)
(6)
For example, using an INA302A2-Q1 and the corresponding gain error equation from 表 8-3, a series resistance
of 10 Ω results in a gain error factor of 0.99. The corresponding gain error is then calculated using 方程式 6,
resulting in a gain error of approximately 1% solely because of the external 10-Ωseries resistors.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
8.1.3 Using the INA30x-Q1 With Common-Mode Transients Greater Than 36 V
With a small amount of additional circuitry, these devices can be used in circuits subject to transients higher than
36 V. Use only zener diodes or zener-type transient absorbers (sometimes referred to as transzorbs). Any other
type of transient absorber has an unacceptable time delay. Start by adding a pair of resistors as a working
impedance for the zener diode, as shown in 图8-4. Keep these resistors as small as possible, preferably 10 Ω or
less. Larger values can be used with an additional induced error resulting from a reduced signal that actually
reaches the device input pins. Many applications are satisfied with a 10-Ω resistor along with conventional zener
diodes of the lowest power rating available because this circuit limits only short-term transients. This combination
uses the least amount of board space. These diodes can be found in packages as small as SOT-523 or
SOD-523.
2.7 V to 5.5 V
CBYPASS
0.1 mF
RLIMIT1
RPULL-UP1
10 kW
RPULL-UP2
LIMIT1
VS
10 kW
ILIMIT1
Power Supply
0 V to 36 V
+
ALERT1
LATCH1
IN+
+
RPROTECT
< 10 W
OUT
Gain = 20,
50, 100
RSENSE
ILIMIT2
IN-
LATCH2
ALERT2
DELAY
+
LOAD
CDELAY
REF
LIMIT2
GND
RLIMIT2
Reference
Voltage
图8-4. Transient Protection
Copyright © 2021 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
8.2 Typical Application
The INA30x-Q1 are designed to be easily configured for detecting multiple out-of-range current conditions in an
application. These devices are capable of monitoring and providing overcurrent detection of bidirectional
currents. By using the REF pin of the INA303-Q1, both positive and negative overcurrent events can be
detected.
(+)
) ( -
Bidirectional
Current Monitoring
RSENSE
2.7 V to 5.5 V
CBYPASS
0.1 µF
RLIMIT1
RPULL-UP
RD
LIMIT1
INA303-Q1
VS
100 kW
10 kW
ILIMIT1
+
-
ALERT1
LATCH1
System
Alert
IN+
+
OUT
Current
Sense
VS
CBYP
0.1 µF
ILIMIT2
IN-
LATCH2
ALERT2
DELAY
-
GND
+
R1
100 kW
LIMIT2
GND
REF
TLV313-Q1
+
RLIMIT2
R2
CFLT
0.1 mF
100 kW
图8-5. Bidirectional Application
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
8.2.1 Design Requirements
To allow for bidirectional monitoring, the INA303-Q1 requires a voltage applied to the REF pin. A voltage that is
half of the supply voltage is usually preferred to allow for maximum output swing in both the positive and
negative current direction. To reduce the errors in the reference voltage, drive the REF pin with a low-impedance
source (such as an op amp or external reference). A low-value resistor divider can be used at the expense of
quiescent current and accuracy. For this design, a single alert output is preferred, so both ALERT1 and ALERT2
are connected together and use a single pullup resistor.
8.2.2 Detailed Design Procedure
To achieve bidirectional monitoring, drive the reference pin halfway between the supply with a resistor divider
buffered by an op amp, as shown in 表 8-4. To reduce the current draw from the supply, use 100-kΩresistors to
create the divide-by-two voltage divider. The TLV313-Q1 is selected to buffer the voltage divider because this
device can operate from a single-supply rail with low IQ and offset voltage. To minimize the response time of the
ALERT2 output, a 100-kΩ pullup resistor was added from the DELAY pin to the VS pin. Select values for
RSENSE, RLIMIT2, and RLIMIT1 based on the desired current-sense levels and trip thresholds using the information
in the Resistor-Controlled Current Limit and Selecting a Current-Sensing Resistor (RSENSE) sections. For this
example, the values of RLIMIT1 and RLIMIT2 were selected so that the positive and negative overcurrent
thresholds are the same. 表 8-4 shows the alert output of the INA303-Q1 application circuit with the capability to
detect both positive and negative overcurrent conditions.
表8-4. Bidirectional Overcurrent Output Status
OVERCURRENT PROTECTION (OCP)
OUTPUT
STATUS
Positive overcurrent detection (OCP+)
Negative overcurrent detection (OCP–)
Normal operation (no OCP)
0
0
1
8.2.3 Application Curve
图 8-6 shows the INA303-Q1 device being used in a bidirectional configuration to detect both negative and
positive overcurrent events.
Positive Limit
0 V
Negative Limit
Time (5 ms/div)
图8-6. Bidirectional Application Curve
Copyright © 2021 Texas Instruments Incorporated
30
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
9 Power Supply Recommendations
The device input circuitry accurately measures signals on common-mode voltages beyond the power-supply
voltage, VS. For example, the voltage applied to the VS power-supply pin can be 5 V, whereas the load power-
supply voltage being monitored (VCM) can be as high as 36 V. At power-up, for applications where the common-
mode voltage (VCM) slew rate is greater than 6 V/μs with a final common-mode voltage greater than 20 V, the
VS supply is recommended to be present before VCM. If the use case requires VCM to be present before VS with
VCM under these same slewing conditions, then a 331-Ωresistor must be added between the VS supply and the
VS pin bypass capacitor.
Power-supply bypass capacitors are required for stability, and must be placed as close as possible to the supply
and ground pins of the device. A typical value for this supply bypass capacitor is 0.1 µF. Applications with noisy
or high-impedance power supplies may require additional decoupling capacitors to reject power-supply noise.
During slow power-up events, current flow through the sense resistor or voltage applied to the REF pin can
result in the output voltage momentarily exceeding the voltage at the LIMITx pins, resulting in an erroneous
indication of an out-of-range event on the ALERTx output. When powering the device with a slow ramping power
rail where an input signal is already present, all alert indications should be disregarded until the supply voltage
has reached the final value.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
31
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
10 Layout
10.1 Layout Guidelines
• Apply connections to the current-sense resistor, RSENSE, on the inside of the resistor pads to avoid additional
voltage losses incurred by the high current traces to the resistor. Route the traces from the current-sense
resistor symmetrically and side-by-side back to the input of the INA to minimize common-mode errors and
noise pickup.
• Place the power-supply bypass capacitor as closely as possible to the supply and ground pins. The
recommended value of this bypass capacitor is 0.1 µF. Additional decoupling capacitance can be added to
compensate for noisy or high-impedance power supplies.
• Make the connection of RLIMIT to the ground pin as direct as possible to limit additional capacitance on this
node. Routing this connection must be limited to the same plane if possible to avoid vias to internal planes. If
the routing can not be made on the same plane and must pass through vias, make sure that a path is routed
from RLIMIT back to the ground pin, and that RLIMIT is not simply connected directly to a ground plane.
• Routing to the delay capacitor must be short and direct. Keep the routing trace from the DELAY pin to the
delay capacitor away from the ALERT2 trace (or any other noisy signals) to minimize any coupling effects. If
no delay capacitor is used do not have any connection to the DELAY pin. Long trace lengths on the DELAY
pin can cause noise to couple to the device, resulting in false trips.
• Pull up the open-drain output pins to the supply voltage rail; a 10-kΩpullup resistor is recommended.
10.2 Layout Example
SYSALERT2
SYSALERT1
Supply Voltage
Power
Supply
RPULL-UP1
Bottom or
mid-layer
trace
CBYPASS
RPULL-UP2
VIA to Power
Ground Plane
1
2
3
4
5
6
7
14
13
12
11
10
9
VS
IN+
RSENSE
Current Sense
Output
OUT
IN-
ALERT1
ALERT2
DELAY
LIMIT2
NC
LIMIT1
REF
RLIMIT1
CDELAY
INA30x-Q1
GND
LATCH1
LATCH2
VIA to Analog
Ground Plane
8
RLIMIT2
Load
Connect the limit resistors and delay capacitors directly to the GND pin; leave the DELAY pin unconnected or connected to VS through
a pullup resistor if no delay is needed.
图10-1. Recommended Layout
Copyright © 2021 Texas Instruments Incorporated
32
Submit Document Feedback
Product Folder Links: INA302-Q1 INA303-Q1
INA302-Q1, INA303-Q1
ZHCSJJ1A –MARCH 2019 –REVISED MAY 2021
www.ti.com.cn
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
• Texas Instruments, TLVx313-Q1 Low Power Rail-to-Rail In/Out 750-µV Typical Offset Op Amps data sheet
• Texas Instruments, Monitoring Current for Multiple Out-of-Range Conditions application report
11.2 接收文档更新通知
要接收文档更新通知,请导航至 ti.com 上的器件产品文件夹。点击订阅更新 进行注册,即可每周接收产品信息更
改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
11.3 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料,可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范,并且不一定反映 TI 的观点;请参阅
TI 的《使用条款》。
11.4 Related Links
表 11-1 lists quick access links. Categories include technical documents, support and community resources,
tools and software, and quick access to order now.
表11-1. Related Links
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
PARTS
PRODUCT FOLDER
ORDER NOW
INA302-Q1
INA303-Q1
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
11.5 Trademarks
TI E2E™ is a trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
11.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.7 术语表
TI 术语表
本术语表列出并解释了术语、首字母缩略词和定义。
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
33
Product Folder Links: INA302-Q1 INA303-Q1
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受TI 的销售条款(https:www.ti.com/legal/termsofsale.html) 或ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI
提供这些资源并不会扩展或以其他方式更改TI 针对TI 产品发布的适用的担保或担保免责声明。重要声明
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021,德州仪器(TI) 公司
PACKAGE OPTION ADDENDUM
www.ti.com
23-Mar-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
INA302A1QPWRQ1
INA302A2QPWRQ1
INA302A3QPWRQ1
INA303A1QPWRQ1
INA303A2QPWRQ1
INA303A3QPWRQ1
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
TSSOP
TSSOP
TSSOP
TSSOP
TSSOP
TSSOP
PW
PW
PW
PW
PW
PW
14
14
14
14
14
14
2000 RoHS & Green
2000 RoHS & Green
2000 RoHS & Green
2000 RoHS & Green
2000 RoHS & Green
2000 RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
I302A1Q
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
I302A2Q
I302A3Q
I303A1Q
I303A2Q
I303A3Q
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Mar-2021
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA302-Q1, INA303-Q1 :
Catalog : INA302, INA303
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他 TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款 (https:www.ti.com.cn/zh-cn/legal/termsofsale.html) 或 ti.com.cn 上其他适用条款/TI 产品随附的其他适用条款
的约束。TI 提供这些资源并不会扩展或以其他方式更改 TI 针对 TI 产品发布的适用的担保或担保免责声明。IMPORTANT NOTICE
邮寄地址:上海市浦东新区世纪大道 1568 号中建大厦 32 楼,邮政编码:200122
Copyright © 2021 德州仪器半导体技术(上海)有限公司
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明