LM20323MH/NOPB [TI]
4.5-36V 3A 电流模式同步降压稳压器 | PWP | 20 | -40 to 125;型号: | LM20323MH/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 4.5-36V 3A 电流模式同步降压稳压器 | PWP | 20 | -40 to 125 稳压器 |
文件: | 总30页 (文件大小:1399K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
LM20323 36V, 3A 500 kHz Synchronous Buck Regulator
Check for Samples: LM20323
1
FEATURES
APPLICATIONS
2
•
•
•
•
4.5V to 36V Input Voltage Range
•
•
•
Simple to Design, high Efficiency Point of
Load Regulation from a 4.5V to 36V Bus
3A Output Current, 5.2A Peak Current
130 mΩ/110 mΩ Integrated Power MOSFETs
High Performance DSPs, FPGAs, ASICs and
Microprocessors
93% Peak Efficiency with Synchronous
Rectification
Communications Infrastructure, Automotive
DESCRIPTION
•
•
1.5% Feedback Voltage Accuracy
The LM20323 is a full featured 500kHz synchronous
buck regulator capable of delivering up to 3A of load
current. The current mode control loop is externally
compensated with only two components, offering both
high performance and ease of use. The device is
optimized to work over the input voltage range of
4.5V to 36V making it well suited for high voltage
systems.
Current Mode Control, Selectable
Compensation
•
•
•
•
Fixed 500 kHz Switching Frequency
Adjustable Output Voltage Down to 0.8V
Compatible with Pre-biased Loads
Programmable Soft-start with External
Capacitor
The device features internal Over Voltage Protection
(OVP) and Over Current Protection (OCP) circuits for
increased system reliability. A precision Enable pin
and integrated UVLO allows the turn-on of the device
to be tightly controlled and sequenced. Startup inrush
currents are limited by both an internally fixed and
externally adjustable soft-start circuit. Fault detection
and supply sequencing are possible with the
integrated power good (PGOOD) circuit.
•
•
•
Precision Enable Pin with Hysteresis
Integrated OVP, UVLO, PGOOD
Internally Protected with Peak Current Limit,
Thermal Shutdown and Restart
•
Accurate Current Limit Minimizes Inductor
Size
•
•
Non-linear Current Mode Slope Compensation
20-Pin HTSSOP Exposed Pad Package
Simplified Application Circuit
LM20323
BOOT
C
BOOT
L
V
SW
V
IN
OUT
VIN
D1
(Optional)
C
IN
R
FB1
C
OUT
EN
FB
R
FB2
COMP
PGOOD
SS/TRK
AGND
VCC
GND
R
C
C1
C
VCC
C1
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
DESCRIPTION (CONTINUED)
The LM20323 is designed to work well in multi-rail power supply architectures. The output voltage of the device
can be configured to track a higher voltage rail using the SS/TRK pin. If the output of the LM20323 is pre-biased
at startup it will not sink current to pull the output low until the internal soft-start ramp exceeds the voltage at the
feedback pin.
The LM20323 is offered in an exposed pad 20-pin HTSSOP package that can be soldered to the PCB,
eliminating the need for bulky heatsinks.
Connection Diagram
SS/TRK
FB
1
2
3
4
5
6
7
8
9
20 NC
19 EN
PGOOD
COMP
VIN
18 VCC
17 BOOT
16 VIN
15 VIN
14 SW
13 SW
12 AGND
11 GND
EP
VIN
SW
SW
GND
GND 10
Figure 1. 20-Pin HTSSOP, Top View
See PWP0020A Package
PIN DESCRIPTIONS
Pin(s)
Name
Description
Application Information
1
SS/TRK Soft-Start or Tracking control input
An internal 4.5 µA current source charges an external capacitor to set
the soft-start rate. The PWM can track to an external voltage ramp with
a low impedance source. If left open, an internal 1 ms SS ramp is
activated.
2
3
4
FB
Feedback input to the error amplifier
from the regulated output
This pin is connected to the inverting input of the internal
transconductance error amplifier. An 800 mV reference is internally
connected to the non-inverting input of the error amplifier.
PGOOD Power good output signal
Open drain output indicating the output voltage is regulating within
tolerance. A pull-up resistor of 10 kΩ to 100 kΩ is recommended if this
function is used.
COMP
Output of the internal error amplifier and The loop compensation network should be connected between the
input to the Pulse Width Modulator
Input supply voltage
Switch pin
COMP pin and the AGND pin.
5,6,15,16
7,8,13,14
VIN
SW
Nominal operating range: 4.5V to 36V.
The drain terminal of the internal Synchronous Rectifier power
NMOSFET and the source terminal of the internal Control power
NMOSFET.
9,10,11
12
GND
AGND
BOOT
Ground
Internal reference for the power MOSFETs.
Analog ground
Internal reference for the regulator control functions.
17
Boost input for bootstrap capacitor
An internal diode from VCC to BOOT charges an external capacitor
required from SW to BOOT to power the Control MOSFET gate driver.
18
19
VCC
EN
Output of the high voltage linear
regulator. The VCC voltage is regulated to approximately 5.5 Volts. A 0.1 µF to 1 µF ceramic decoupling
to approximately 5.5V.
VCC tracks VIN up to about 7.2V. Above VIN = 7.2V, VCC is regulated
capacitor is required. The VCC pin is an output only.
Enable or UVLO input
An external voltage divider can be used to set the line undervoltage
lockout threshold. If the EN pin is left unconnected, a 2 µA pull-up
current source pulls the EN pin high to enable the regulator.
20
NC
No Connection
Recommend connecting this pin to GND.
EP
Exposed Exposed pad
Pad
Exposed metal pad on the underside of the package with a weak
electrical connection to GND. Connect this pad to the PC board ground
plane in order to improve heat dissipation.
2
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
VIN to GND
-0.3V to +38V
-0.3V to +43V
-0.3V to +7V
-0.5V to +38V
-1.5V (< 20 ns)
-0.3V to +6V
-0.3V to +8V
-65°C to 150°C
2kV
BOOT to GND
BOOT to SW
SW to GND
SW to GND (Transient)
FB, EN, SS/TRK, COMP, PGOOD to GND
VCC to GND
Storage Temperature
ESD Rating
Human Body Model(3)
(1) Absolute Maximum Ratings indicate limits beyond witch damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but do not ensure specific performance limits. For ensured specifications and test
conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor to each pin.
Operating Ratings
VIN to GND
+4.5V to +36V
Junction Temperature
−40°C to + 125°C
Electrical Characteristics
Unless otherwise stated, the following conditions apply: VVIN = 12V. Limits in standard type are for TJ = 25°C only, limits in
bold face type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and maximum limits are
specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C,
and are provided for reference purposes only.
Symbol
Parameter
Conditions
VVIN = 4.5V to 36V
ISW = 3A
Min
Typ
0.8
130
110
2.3
150
4.25
350
5.5
4.5
5
Max
0.812
225
190
3
Units
V
VFB
Feedback Pin Voltage
0.788
RHSW-DS(ON) High-Side MOSFET On-Resistance
mΩ
mΩ
mA
µA
V
RLSW-DS(ON)
IQ
Low-Side MOSFET On-Resistance
Operating Quiescent Current
Shutdown Quiescent Current
VIN Under Voltage Lockout
VIN Under Voltage Lockout Hysteresis
VCC Voltage
ISW = 3A
VVIN = 4.5V to 36V
VEN = 0V
ISD
180
4.5
VUVLO
Rising VVIN
4
VUVLO(HYS)
VVCC
450
mV
V
IVCC = -5 mA, VEN = 5V
VSS = 0V
ISS
Soft-Start Pin Source Current
Soft-Start/Track Pin Accuracy
BOOT Diode Leakage
2
7
µA
mV
nA
V
VTRKACC
IBOOT
VSS = 0.4V
-10
15
VBOOT = 4V
10
VF-BOOT
Powergood
VFB(OVP)
BOOT Diode Forward Voltage
IBOOT = -100 mA
0.9
1.1
Over Voltage Protection Rising Threshold
VFB(OVP) / VFB
ΔVFB(OVP) / VFB
VFB(PG) / VFB
ΔVFB(PG) / VFB
107
93
110
2
112
3
%
%
VFB(OVP-HYS) Over Voltage Protection Hysteresis
VFB(PG)
VFB(PG-HYS)
TPGOOD
PGOOD Threshold, VOUT Rising
PGOOD Hysteresis
95
2
97
3
%
%
PGOOD Delay
20
1
µs
mA
nA
IPGOOD(SNK)
IPGOOD(SRC)
PGOOD Low Sink Current
PGOOD High Leakage Current
VPGOOD = 0.5V
VPGOOD = 5V
0.6
5
200
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
Electrical Characteristics (continued)
Unless otherwise stated, the following conditions apply: VVIN = 12V. Limits in standard type are for TJ = 25°C only, limits in
bold face type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and maximum limits are
specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C,
and are provided for reference purposes only.
Symbol
Oscillator
FSW1
Parameter
Conditions
Min
Typ
Max
Units
Switching Frequency
Maximum Duty Cycle
470
520
70
570
kHz
%
DMAX
IOUT = 3A
Error Amplifier
IFB
Feedback Pin Bias Current
VFB = 1V
50
400
350
515
2000
7
nA
µA
ICOMP(SRC)
ICOMP(SNK)
gm
COMP Output Source Current
COMP Output Sink Current
VFB = 0V, VCOMP = 0V
VFB = 1.6V, VCOMP = 1.6V
ICOMP = -50 µA to +50 µA
COMP pin open
200
200
450
µA
Error Amplifier DC Transconductance
Error Amplifier Voltage Gain
600
6.0
1.3
µmho
V/V
MHz
AVOL
GBW
Error Amplifier Gain-Bandwidth Product
COMP pin open
Current Limit
ILIM
Cycle By Cycle Positive Current Limit
Cycle By Cycle Negative Current Limit
Cycle By Cycle Current Limit Delay
4.3
1.2
5.2
2.8
150
A
A
ILIMNEG
TILIM
ns
Enable
VIH_EN
EN Pin Rising Threshold
EN Pin Hysteresis
1.25
50
2
V
VEN(HYS)
IEN
mV
µA
EN Source Current
VEN = 0V, VVIN = 12V
Thermal Shutdown
TSD
Thermal Shutdown
Thermal Shutdown Hysteresis
170
20
°C
°C
TSD(HYS)
Thermal Resistance
θJC
θJA
Junction to Case
Junction to Ambient(1)
5.6
27
°C/W
°C/W
0 LFM airflow
(1) Measured on a 4 layer 2" x 2" PCB with 1 oz. copper weight inner layers and 2 oz. outer layers.
4
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
Typical Performance Characteristics
Unless otherwise specified: VVIN = 12V, VOUT = 3.3V, L= 5.6 µH, CSS = 100nF, TA = 25°C for efficiency curves, loop gain plots
and waveforms, and TJ = 25°C for all others.
Efficiency
vs.
Load Current
Error Amplifier Gain
Figure 2.
Figure 3.
Error Amplifier Phase
Line Regulation
Figure 4.
Figure 5.
VCC
vs.
VIN
Load Regulation
Figure 6.
Figure 7.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified: VVIN = 12V, VOUT = 3.3V, L= 5.6 µH, CSS = 100nF, TA = 25°C for efficiency curves, loop gain plots
and waveforms, and TJ = 25°C for all others.
Non-Switching IQ
Shutdown IQ
vs.
VIN
vs.
VIN
Figure 8.
Figure 9.
PGOOD Output Low Level Voltage
Enable Threshold and Hysteresis
vs.
vs.
IPGOOD
Temperature
Figure 10.
Figure 11.
UVLO Threshold and Hysteresis
Enable Current
vs.
Temperature
vs.
Temperature
Figure 12.
Figure 13.
6
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
Typical Performance Characteristics (continued)
Unless otherwise specified: VVIN = 12V, VOUT = 3.3V, L= 5.6 µH, CSS = 100nF, TA = 25°C for efficiency curves, loop gain plots
and waveforms, and TJ = 25°C for all others.
Oscillator Frequency
High-Side FET Resistance
vs.
VIN
vs.
Temperature
Figure 14.
Figure 15.
Low-Side FET Resistance
vs.
Load Transient Response
Temperature
Figure 16.
Figure 17.
Peak Current Limit
vs.
Temperature
Startup with Prebiased Output
Figure 18.
Figure 19.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified: VVIN = 12V, VOUT = 3.3V, L= 5.6 µH, CSS = 100nF, TA = 25°C for efficiency curves, loop gain plots
and waveforms, and TJ = 25°C for all others.
Startup with CSS = 0
Startup with CSS = 100 nF
Figure 20.
Figure 21.
Startup with Applied Track Signal
Figure 22.
8
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
Block Diagram
VCC_INT
BOOT
INTERNAL
+5.5V
REGULATOR
BOOT
VCC
VCC
+5.5V
REGULATOR
ENABLE_INT
VIN
UVLO
+
-
2.7V
4.25V
+2.7V
SLOPE COMP
REGULATOR
COMP
2.7V
CURRENT SENSE
+
4.5 mA
DISCHARGE
ERROR AMP
SS/TRK
FB
g
= 515 mmho
m
+
DISCHARGE
CURRENT LIMIT
-
BOOT
+
-
+
5.2A
VREF
800 mV
+
-
+
-
PWM COMPARATOR
NEGATIVE
CURRENT LIMIT
+
+
-
OVERVOLTAGE
PG-L
-
-2.8A
880 mV
740 mV
CONTROL
LOGIC
SW
+
-
UNDERVOLTAGE
VCC
VCC_INT
2 mA
THERMAL
PROTECTION
ENABLE_INT
+
-
1.25V
EN
500 kHz
OSCILLATOR
GND
PGOOD
PG-L
AGND
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
OPERATION DESCRIPTION
GENERAL
The LM20323 switching regulator features all of the functions necessary to implement an efficient buck regulator
using a minimum number of external components. This easy to use regulator features two integrated switches
and is capable of supplying up to 3A of continuous output current. The regulator utilizes peak current mode
control with nonlinear slope compensation to optimize stability and transient response over the entire output
voltage range. Peak current mode control also provides inherent line feed-forward, cycle-by-cycle current limiting
and easy loop compensation. The 500kHz switching frequency minimizes the inductor size while keeping
switching losses low allowing use of a small inductor while still achieving efficiencies as high as 93%. The
precision internal voltage reference allows the output to be set as low as 0.8V. Fault protection features include:
current limiting, thermal shutdown, over voltage protection, and shutdown capability. The device is available in
the HTSSOP package featuring an exposed pad to aid thermal dissipation. The typical application circuit for the
LM20323 is shown in Figure 23 in the design guide.
PRECISION ENABLE
The enable (EN) pin allows the output of the device to be enabled or disabled with an external control signal.
This pin is a precision analog input that enables the device when the voltage exceeds 1.25V (typical). The EN pin
has 50 mV of hysteresis and will disable the output when the enable voltage falls below 1.2V (typical). If the EN
pin is not used, it should be disconnected so the internal 2 µA pull-up will default this function to the enabled
condition. Since the enable pin has a precise turn-on threshold it can be used along with an external resistor
divider network from VIN to configure the device to turn-on at a precise input voltage. The precision enable
circuitry will remain active even when the device is disabled.
PEAK CURRENT MODE CONTROL
In most cases, the peak current mode control architecture used in the LM20323 only requires two external
components to achieve a stable design. The compensation can be selected to accommodate any capacitor type
or value. The external compensation also allows the user to set the crossover frequency and optimize the
transient performance of the device.
For duty cycles above 50% all peak current mode control buck converters require the addition of an artificial
ramp to avoid sub-harmonic oscillation. This artificial linear ramp is commonly referred to as slope compensation.
What makes the LM20323 unique is the amount of slope compensation will change depending on the output
voltage. When operating at high output voltages the device will have more slope compensation than when
operating at lower output voltages. This is accomplished in the LM20323 by using a non-linear parabolic ramp for
the slope compensation. The parabolic slope compensation of the LM20323 is an improvement over the
traditional linear slope compensation because it optimizes the stability of the device over the entire output voltage
range.
CURRENT LIMIT
The precise current limit enables the device to operate with smaller inductors that have lower saturation currents.
When the peak inductor current reaches the current limit threshold, an over current event is triggered and the
internal high-side FET turns off and the low-side FET turns on, allowing the inductor current to ramp down until
the next switching cycle. For each sequential over-current event, the reference voltage is decremented and PWM
pulses are skipped resulting in a current limit that does not aggressively fold back for brief over-current events,
while at the same time providing frequency and voltage foldback protection during hard short circuit conditions.
SOFT-START AND VOLTAGE TRACKING
The SS/TRK pin is a dual function pin that can be used to set the startup time or track an external voltage
source. The startup or soft-start time can be adjusted by connecting a capacitor from the SS/TRK pin to ground.
The soft-start feature allows the regulator output to gradually reach the steady state operating point, thus
reducing stresses on the input supply and controlling startup current. If no soft-start capacitor is used the device
defaults to the internal soft-start circuitry resulting in a startup time of approximately 1 ms. For applications that
require a monotonic startup or utilize the PGOOD pin, an external soft-start capacitor is recommended. The
SS/TRK pin can also be set to track an external voltage source. The tracking behavior can be adjusted by two
external resistors connected to the SS/TRK pin as shown in Figure 28 in the design guide.
10
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
PRE-BIAS STARTUP CAPABILITY
The LM20323 is in a pre-biased state when it starts up with an output voltage greater than zero. This often
occurs in many multi-rail applications such as when powering an FPGA, ASIC, or DSP. In these applications the
output can be pre-biased through parasitic conduction paths from one supply rail to another. Even though the
LM20323 is a synchronous converter, it will not pull the output low when a pre-bias condition exists. During start
up the LM20323 will not sink current until the soft-start voltage exceeds the voltage on the FB pin. Since the
device cannot sink current, it protects the load from damage that might otherwise occur if current is conducted
through the parasitic paths of the load.
POWER GOOD AND OVER VOLTAGE FAULT HANDLING
The LM20323 has built in under and over voltage comparators that control the power switches. Whenever there
is an excursion in output voltage above the set OVP threshold, the part will terminate the present on-pulse, turn-
on the low-side FET, and pull the PGOOD pin low. The low-side FET will remain on until either the FB voltage
falls back into regulation or the negative current limit is triggered which in turn tri-states the FETs. If the output
reaches the UVP threshold the part will continue switching and the PGOOD pin will be deasserted and go low.
Typical values for the PGOOD resistor are on the order of 100 kΩ or less. To avoid false tripping during transient
glitches the PGOOD pin has 20 µs of built in deglitch time to both rising and falling edges.
UVLO
The LM20323 has an internal under-voltage lockout protection circuit that keeps the device from switching until
the input voltage reaches 4.25V (typical). The UVLO threshold has 350 mV of hysteresis that keeps the device
from responding to power-on glitches during start up. If desired the turn-on point of the supply can be changed
by using the precision enable pin and a resistor divider network connected to VIN as shown in Figure 27 in the
design guide.
THERMAL PROTECTION
Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum
junction temperature is exceeded. When activated, typically at 170°C, the LM20323 tri-states the power FETs
and resets soft-start. After the junction cools to approximately 150°C, the part starts up using the normal start up
routine. This feature is provided to prevent catastrophic failures from accidental device overheating.
Design Guide
This section walks the designer through the steps necessary to select the external components to build a fully
functional power supply. As with any DC-DC converter numerous trade-offs are possible to optimize the design
for efficiency, size, or performance. These will be taken into account and highlighted throughout this discussion.
To facilitate component selection discussions the circuit shown in Figure 23 below may be used as a reference.
Unless otherwise indicated, all formulas assume units of amps (A) for current, farads (F) for capacitance, henries
(H) for inductance and volts (V) for voltages.
LM20323
BOOT
C
BOOT
L
V
SW
FB
V
IN
VIN
OUT
D1
(Optional)
C
C
IN2
IN1
R
R
FB1
C
OUT
EN
V
PULLUP
FB2
COMP
R
PG
PGOOD
VCC
R
C
C1
SS/TRK
AGND GND
C
SS
C
VCC
C1
Figure 23. Typical Application Circuit
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
The first equation to calculate for any buck converter is duty-cycle. Ignoring conduction losses associated with
the FETs and parasitic resistances it can be approximated by:
VOUT
D =
VIN
(1)
INDUCTOR SELECTION (L)
The inductor value is determined based on the operating frequency, load current, ripple current and duty cycle.
The inductor selected should have a saturation current rating greater than the peak current limit of the device.
Keep in mind the specified current limit does not account for delay of the current limit comparator, therefore the
current limit in the application may be higher than the specified value. To optimize the performance and prevent
the device from entering current limit at maximum load, the inductance is typically selected such that the ripple
current, ΔiL, is not greater than 30% of the rated output current. Figure 24 illustrates the switch and inductor
ripple current waveforms. Once the input voltage, output voltage, operating frequency and desired ripple current
are known, the minimum value for the inductor can be calculated by the formula shown below:
(VIN - VOUT) x D
LMIN
=
DiL x f
SW
(2)
V
SW
V
IN
Time
I
L
I
= I
OUT
DiL
L AVG
Time
Figure 24. Switch and Inductor Current Waveforms
If needed, slightly smaller value inductors can be used, however, the peak inductor current, IOUT + ΔiL/2, should
be kept below the peak current limit of the device. In general, the inductor ripple current, ΔiL, should be more
than 10% of the rated output current to provide adequate current sense information for the current mode control
loop. If the ripple current in the inductor is too low, the control loop will not have sufficient current sense
information and can be prone to instability.
OUTPUT CAPACITOR SELECTION (COUT
)
The output capacitor, COUT, filters the inductor ripple current and provides a source of charge for transient load
conditions. A wide range of output capacitors may be used with the LM20323 that provide excellent performance.
The best performance is typically obtained using ceramic, SP or OSCON type chemistries. Typical trade-offs are
that the ceramic capacitor provides extremely low ESR to reduce the output ripple voltage and noise spikes,
while the SP and OSCON capacitors provide a large bulk capacitance in a small volume for transient loading
conditions.
When selecting the value for the output capacitor, the two performance characteristics to consider are the output
voltage ripple and transient response. The output voltage ripple can be approximated by using the following
formula:
12
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
1
DVOUT = DiL x
RESR
+
8 x fSW x COUT
where
•
•
•
•
ΔVOUT (V) is the amount of peak to peak voltage ripple at the power supply output
RESR (Ω) is the series resistance of the output capacitor
fSW(Hz) is the switching frequency
COUT (F) is the output capacitance used in the design
(3)
The amount of output ripple that can be tolerated is application specific; however a general recommendation is to
keep the output ripple less than 1% of the rated output voltage. Keep in mind ceramic capacitors are sometimes
preferred because they have very low ESR; however, depending on package and voltage rating of the capacitor
the value of the capacitance can drop significantly with applied voltage. The output capacitor selection will also
affect the output voltage droop during a load transient. The peak droop on the output voltage during a load
transient is dependent on many factors; however, an approximation of the transient droop ignoring loop
bandwidth can be obtained using the following equation:
2
L x DIOUTSTEP
VDROOP = DIOUTSTEP x RESR
+
COUT x (VIN - VOUT
)
where
•
•
•
•
•
•
•
COUT (F) is the minimum required output capacitance
L (H) is the value of the inductor
VDROOP (V) is the output voltage drop ignoring loop bandwidth considerations
ΔIOUTSTEP (A) is the load step change
RESR (Ω) is the output capacitor ESR
VIN (V) is the input voltage
VOUT (V) is the set regulator output voltage
(4)
Both the tolerance and voltage coefficient of the capacitor should be examined when designing for a specific
output ripple or transient droop target.
INPUT CAPACITOR SELECTION
Good quality input capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the
switch current during the on-time. In general it is recommended to use a ceramic capacitor for the input as they
provide both a low impedance and small footprint. One important note is to use a good dielectric for the ceramic
capacitor such as X5R or X7R. These provide better over temperature performance and also minimize the DC
voltage derating that occurs on Y5V capacitors. The input capacitors CIN1 and CIN2 should be placed as close as
possible to the VIN and GND pins on both sides of the device.
Non-ceramic input capacitors should be selected for RMS current rating and minimum ripple voltage. A good
approximation for the required ripple current rating is given by the relationship:
IIN-RMS = IOUT D(1 - D)
(5)
As indicated by the RMS ripple current equation, highest requirement for RMS current rating occurs at 50% duty
cycle. For this case, the RMS ripple current rating of the input capacitor should be greater than half the output
current. For best performance, low ESR ceramic capacitors should be placed in parallel with higher capacitance
capacitors to provide the best input filtering for the device.
SETTING THE OUTPUT VOLTAGE (RFB1, RFB2
)
The resistors RFB1 and RFB2 are selected to set the output voltage for the device. Table 1 provides suggestions
for RFB1 and RFB2 for common output voltages.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
Table 1. Suggested Values for RFB1 and RFB2
RFB1(kΩ)
short
4.99
RFB2(kΩ)
open
10
VOUT
0.8
1.2
1.5
1.8
2.5
3.3
5.0
8.87
10.2
10.2
10.2
10.2
10
12.7
21.5
31.6
52.3
If different output voltages are required, RFB2 should be selected to be between 4.99 kΩ to 49.9 kΩ and RFB1 can
be calculated using the equation below.
VOUT
x RFB2
- 1
RFB1
=
0.8
(6)
LOOP COMPENSATION (RC1, CC1
)
The purpose of loop compensation is to meet static and dynamic performance requirements while maintaining
adequate stability. Optimal loop compensation depends on the output capacitor, inductor, load and the device
itself. Table 2 below gives values for the compensation network that will result in a stable system when using a
150 µF, 6.3V POSCAP (6TPB150MAZB) output capacitor.
Table 2. Recommended Compensation for
COUT = 150 µF, IOUT = 3A
VIN
12
12
12
12
12
12
5
VOUT
5
L (µH)
6.8
5.6
4.7
3.3
2.2
1.5
2.2
3.3
2.2
2
RC (kΩ)
45.3
32.4
30.9
19.1
21.5
15
CC1 (nF)
4.7
3.3
2.5
1.5
1.2
0.8
3.3
2.5
1.5
1.2
0.8
4.7
3.3
3.3
2.2
2.2
29.4
37.4
26.7
22.1
15
2.2
5
2.2
5
2.2
5
2.2
5
1.5
2.2
If the desired solution differs from the table above the loop transfer function should be analyzed to optimize the
loop compensation. The overall loop transfer function is the product of the power stage and the feedback network
transfer functions. For stability purposes, the objective is to have a loop gain slope that is -20dB/decade from a
very low frequency to beyond the crossover frequency. Figure 25 shows the transfer functions for power stage,
feedback/compensation network, and the resulting compensated loop for the LM20323.
14
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
Output Filter Pole, f
P(FIL)
A
M
0 dB
Output Filter Zero, f
Z(FIL)
Complex Double Pole, f
P(MOD)
Error Amp Pole, f
P1(EA)
A
EA
Optional Error Amp
Pole, f
P2(EA)
0 dB
Error Amp Zero, f
Z(EA)
A
EA
+ A
M
Error Amp Pole, f
P(EA)
0 dB
Complex Double Pole, f
P(MOD)
f
f
/2
C
SW
FREQUENCY (Hz)
Figure 25. LM20323 Loop Compensation
The power stage transfer function is dictated by the modulator, output LC filter, and load; while the feedback
transfer function is set by the feedback resistor ratio, error amp gain and external compensation network.
To achieve a -20dB/decade slope, the error amplifier zero, located at fZ(EA), should be positioned to cancel the
output filter pole (fP(FIL)).
Compensation of the LM20323 is achieved by adding an RC network as shown in Figure 26 below.
LM20323
COMP
R
C
C1
C
C2
(optional)
C1
Figure 26. Compensation Network for LM20323
A good starting value for CC1 for most applications is 2.2 nF. Once the value of CC1 is chosen the value of RC1
should be approximated using the equation below to cancel the output filter pole (fP(FIL)) as shown in Figure 25.
-1
CC1
IOUT
2 x D
x
+
RC1
=
COUT
VOUT fSW x L
(7)
A higher crossover frequency can be obtained, usually at the expense of phase margin, by lowering the value of
CC1 and recalculating the value of RC1. Likewise, increasing CC1 and recalculating RC1 will provide additional
phase margin at a lower crossover frequency. As with any attempt to compensate the LM20323 the stability of
the system should be verified for desired transient droop and settling time.
For low duty cycle operation, when the on-time of the switch node is less than 200ns, an additional capacitor
(CC2) should be added from the COMP pin to AGND. The recommended value of this capacitor is 20pF. If low
duty cycle jitter on the switch node is observed, the value of this capacitor can be increased to improve noise
immunity; however, values much larger than 100pF will cause the pole fP2(EA) to move to a lower frequency
degrading the loop stability.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
BOOT CAPACITOR (CBOOT
)
The LM20323 integrates an N-channel buck switch and associated floating high voltage level shift / gate driver.
This gate driver circuit works in conjunction with an internal diode and an external bootstrap capacitor. A 0.1 µF
ceramic capacitor, connected with short traces between the BOOT pin and SW pin, is recommended. During the
off-time of the buck switch, the SW pin voltage is approximately 0V and the bootstrap capacitor is charged from
VCC through the internal bootstrap diode.
SUB-REGULATOR BYPASS CAPACITOR (CVCC
)
The capacitor at the VCC pin provides noise filtering for the internal sub-regulator. The recommended value of
CVCC should be no smaller than 0.1 µF and no greater than 1 µF. The capacitor should be a good quality ceramic
X5R or X7R capacitor. In general, a 1 µF ceramic capacitor is recommended for most applications. The VCC
regulator should not be used for other functions since it isn't protected against short circuit.
SETTING THE START UP TIME (CSS
)
The addition of a capacitor connected from the SS pin to ground sets the time at which the output voltage will
reach the final regulated value. Larger values for CSS will result in longer start up times. Table 3, shown below
provides a list of soft start capacitors and the corresponding typical start up times.
Table 3. Start Up Times for Different Soft-Start Capacitors
Start Up Time (ms)
CSS (nF)
none
33
1
5
10
15
20
68
100
120
If different start up times are needed the equation shown below can be used to calculate the start up time.
0.8V x CSS
tSS
=
ISS
(8)
As shown above, the start up time is influenced by the value of the soft-start capacitor CSS and the 4.5 µA soft-
start pin current ISS
.
While the soft-start capacitor can be sized to meet many start up requirements, there are limitations to its size.
The soft-start time can never be faster than 1 ms due to the internal default 1 ms start up time. When the device
is enabled there is an approximate time interval of 50 µs when the soft-start capacitor will be discharged just
prior to the soft-start ramp. If the enable pin is rapidly pulsed or the soft-start capacitor is large there may not be
enough time for CSS to completely discharge resulting in start up times less than predicted. To aid in discharging
of soft-start capacitor during long disable periods an external 1MΩ resistor from SS/TRK to ground can be used
without greatly affecting the start up time.
USING PRECISION ENABLE AND POWER GOOD
The precision enable (EN) and power good (PGOOD) pins of the LM20323 can be used to address many
sequencing requirements. The turn-on of the LM20323 can be controlled with the precision enable pin by using
two external resistors as shown in Figure 27 .
External
Power Supply
V
OUT1
LM20323
R
A
R
B
V
OUT2
EN
Figure 27. Sequencing LM20323 with Precision Enable
16
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
The value for resistor RB can be selected by the user to control the current through the divider. Typically this
resistor will be selected to be between 1 kΩ and 49.9 kΩ. Once the value for RB is chosen the resistor RA can be
solved using the equation below to set the desired turn-on voltage.
VTO
VIH_EN
x R
B
- 1
RA
=
(9)
When designing for a specific turn-on threshold (VTO) the tolerance on the input supply, enable threshold
(VIH_EN), and external resistors need to be considered to ensure proper turn-on of the device.
The LM20323 features an open drain power good (PGOOD) pin to sequence external supplies or loads and to
provide fault detection. This pin requires an external resistor (RPG) to pull PGOOD high when the output is within
the PGOOD tolerance window. Typical values for this resistor range from 10 kΩ to 100 kΩ.
TRACKING AN EXTERNAL SUPPLY
By using a properly chosen resistor divider network connected to the SS/TRK pin, as shown in Figure 28, the
output of the LM20323 can be configured to track an external voltage source to obtain a simultaneous or
ratiometric start up.
External
Power Supply
V
OUT1
LM20323
R1
R2
EN
V
OUT2
SS/TRK
Figure 28. Tracking an External Supply
Since the soft-start charging current ISS is always present on the SS/TRK pin, the size of R2 should be less than
10 kΩ to minimize the errors in the tracking output. Once a value for R2 is selected the value for R1 can be
calculated using appropriate equation in Figure 29, to give the desired start up. Figure 28 shows two common
start up sequences; the top waveform shows a simultaneous start up while the waveform at the bottom illustrates
a ratiometric start up.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
SIMULTANEOUS START UP
V
V
OUT1
OUT2
≈
’
V
OUT2
0.8V
∆
∆
÷
x
÷
-1
R1=
V
R2
«
◊
V
EN
< 0.8 x V
OUT2
OUT1
TIME
RATIOMETRIC START UP
V
OUT1
(
)
-1
x
R2
V
R1=
OUT1
V
OUT2
V
EN
TIME
Figure 29. Common Start Up Sequences
A simultaneous start up is preferred when powering most FPGAs, DSPs, or other microprocessors. In these
systems the higher voltage, VOUT1, usually powers the I/O, and the lower voltage, VOUT2, powers the core. A
simultaneous start up provides a more robust power up for these applications since it avoids turning on any
parasitic conduction paths that may exist between the core and the I/O pins of the processor.
The second most common power on behavior is known as a ratiometric start up. This start up is preferred in
applications where both supplies need to be at the final value at the same time.
Similar to the soft-start function, the fastest start up possible is 1ms regardless of the rise time of the tracking
voltage. When using the track feature the final voltage seen by the SS/TRACK pin should exceed 1V to provide
sufficient overdrive and transient immunity.
BENEFIT OF AN EXTERNAL SCHOTTKY
The LM20323 employs a 40ns dead time between conduction of the control and synchronous FETs in order to
avoid the situation where both FETs simultaneously conduct, causing shoot-through current. During the dead
time, the body diode of the synchronous FET acts as a free-wheeling diode and conducts the inductor current.
The structure of the high voltage DMOS is optimized for high breakdown voltage, but this typically leads to
inefficient body diode conduction due to the reverse recovery charge. The loss associated with the reverse
recovery of the body diode of the synchronous FET manifests itself as a loss proportional to load current and
switching frequency. The additional efficiency loss becomes apparent at higher input voltages and switching
frequencies. One simple solution is to use a small 1A external Schottky diode between SW and GND as shown
in Figure 34. The external Schottky diode effectively conducts all inductor current during the dead time,
minimizing the current passing through the synchronous MOSFET body diode and eliminating reverse recovery
losses.
18
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
The external Schottky conducts currents for a very small portion of the switching cycle, therefore the average
current is low. An external Schottky rated for 1A will improve efficiency by several percent in some applications.
A Schottky rated at a higher current will not significantly improve efficiency and may be worse due to the
increased reverse capacitance. The forward voltage of the synchronous MOSFET body diode is approximately
700 mV, therefore an external Schottky with a forward voltage less than or equal to 700 mV should be selected
to ensure the majority of the dead time current is carried by the Schottky.
THERMAL CONSIDERATIONS
The thermal characteristics of the LM20323 are specified using the parameter θJA, which relates the junction
temperature to the ambient temperature. Although the value of θJA is dependant on many variables, it still can be
used to approximate the operating junction temperature of the device.
To obtain an estimate of the device junction temperature, one may use the following relationship:
TJ = PD x θJA + TA
(10)
and
PD = PIN x (1 - Efficiency) - 1.1 x (IOUT)2 x DCR
where
•
•
•
•
•
•
TJ is the junction temperature in °C
PIN is the input power in Watts (PIN = VIN x IIN)
θJA is the junction to ambient thermal resistance for the LM20323
TA is the ambient temperature in °C
IOUT is the output load current
DCR is the inductor series resistance
(11)
It is important to always keep the operating junction temperature (TJ) below 125°C for reliable operation. If the
junction temperature exceeds 170°C the device will cycle in and out of thermal shutdown. If thermal shutdown
occurs it is a sign of inadequate heatsinking or excessive power dissipation in the device.
Figure 30 and Figure 31 can be used as a guide to avoid exceeding the maximum junction temperature of 125°C
provided an external 1A Schottky diode, such as Central Semiconductor's CMMSH1-40-NST, is used to improve
reverse recovery losses.
Figure 30. Safe Thermal Operating Areas (IOUT = 3A)
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
Figure 31. Safe Thermal Operating Areas (IOUT = 2.5A)
The dashed lines in the figures above show an approximation of the minimum and maximum duty cycle
limitations; while, the solid lines define areas of operation for a given ambient temperature. This data for the
figure was derived assuming the device is operating at 3A continuous output current on a 4 layer PCB with an
copper area greater than 4 square inches exhibiting a thermal characteristic less than 27 °C/W. Since the
internal losses are dominated by the FETs a slight reduction in current by 500mA allows for much larger regions
of operation, as shown in Figure 31.
Figure 32, shown below, provides a better approximation of the θJA for a given PCB copper area. The PCB used
in this test consisted of 4 layers: 1oz. copper was used for the internal layers while the external layers were
plated to 2oz. copper weight. To provide an optimal thermal connection, a 5 x 4 array of 12 mil thermal vias
located under the thermal pad was used to connect the 4 layers.
Figure 32. Thermal Resistance vs PCB Area (4 Layer Board)
PCB LAYOUT CONSIDERATIONS
PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance
of a DC-DC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss
in the traces. These can send erroneous signals to the DC-DC converter resulting in poor regulation or instability.
Good layout can be implemented by following a few simple design rules.
1. Minimize area of switched current loops. In a buck regulator there are two loops where currents are switched
at high slew rates. The first loop starts from the input capacitor, to the regulator VIN pin, to the regulator SW pin,
to the inductor then out to the output capacitor and load. The second loop starts from the output capacitor
ground, to the regulator GND pins, to the inductor and then out to the load (see Figure 33). To minimize both
loop areas the input capacitor should be placed as close as possible to the VIN pin. Grounding for both the input
and output capacitor should consist of a small localized top side plane that connects to GND and the exposed
pad (EP). The inductor should be placed as close as possible to the SW pin and output capacitor.
20
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
2. Minimize the copper area of the switch node. Since the LM20323 has the SW pins on opposite sides of the
package it is recommended that the SW pins should be connected with a trace that runs around the package.
The inductor should be placed at an equal distance from the SW pins using 100 mil wide traces to minimize
capacitive and conductive losses.
3. Have a single point ground for all device grounds located under the EP. The ground connections for the
compensation, feedback, and soft-start components should be connected together then routed to the EP pin of
the device. The AGND pin should connect to GND under the EP. If not properly handled poor grounding can
result in degraded load regulation or erratic switching behavior.
4. Minimize trace length to the FB pin. Since the feedback node can be high impedance the trace from the output
resistor divider to FB pin should be as short as possible. This is most important when high value resistors are
used to set the output voltage. The feedback trace should be routed away from the SW pin and inductor to avoid
contaminating the feedback signal with switch noise.
5. Make input and output bus connections as wide as possible. This reduces any voltage drops on the input or
output of the converter and can improve efficiency. Voltage accuracy at the load is important so make sure
feedback voltage sense is made at the load. Doing so will correct for voltage drops at the load and provide the
best output accuracy.
6. Provide adequate device heatsinking. For most 3A designs a four layer board is recommended. Use as many
vias as is possible to connect the EP to the power plane heatsink. For best results use a 5x4 via array with a
minimum via diameter of 12 mils. "Via tenting" with the solder mask may be necessary to prevent wicking of the
solder paste applied to the EP. See the THERMAL CONSIDERATIONS section to ensure enough copper
heatsinking area is used to keep the junction temperature below 125°C.
LM20323
L
SW
PVIN
V
OUT
C
IN
C
OUT
PGND
LOOP1
LOOP2
Figure 33. Schematic of LM20323 Highlighting Layout Sensitive Nodes
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM20323
LM20323
SNVS557C –MAY 2008–REVISED APRIL 2013
www.ti.com
V
IN
C1
C2
C3
C2, C3 should be placed at VIN
pins 5,6 and 15,16 respectively.
GND
U1
5
6
15
16
VIN
VIN
VIN
VIN
V
OUT
18
3
VCC
C4
R1
PGOOD
17
BOOT
PGOOD
C5
7
8
13
14
ENABLE
SW
SW
SW
SW
19
1
EN
SS
L1
V
OUT
4
2
COMP
FB
C9
9
10
11
D1
GND
GND
GND
GND
R3
(OPTIONAL
for improved
Efficiency)
12
20
AGND
NC
C8
R2
EP
C6
C7
R4
Figure 34. Typical Application Schematic
Table 4. Bill of Materials (VIN = 12V, VOUT = 3.3V, IOUT = 3A)
ID
U1
Qty
Part Number
LM20323MH
Size
HTSSOP
1210
Description
Vendor
1
1
2
1
1
1
1
1
1
IC, Switching Regulator
22µF, X5R, 25V, 20%
4.7µF, X5R, 25V, 10%
100nF, X7R, 50V, 10%
1µF, X7R, 10V, 10%
10pF, C0G, 50V, 5%
1nF, C0G, 50V, 5%
TI
TDK
C1
C3225X5R1E226M
GRM21BR61E475KA12L
C1608X7R1H104K
C1608X5R1A105K
C1608C0G1H100J
C1608C0G1H102J
6TPB150MAZB
C2, C3
C5, C6
C4
0805
MuRata
TDK
0603
0603
TDK
C7
0603
TDK
C8
0603
TDK
C9
B
150µF,POSCAP, 6.3V, 20%
Vr = 40V, Io = 1A, Vf = 0.55V
Sanyo
D1
CMMSH1-40-NST
SOD123
Central
Semiconductor
L1
R1, R4
R2
1
2
1
1
IHLP4040DZER5R6M01
CRCW06031002F
CRCW06034992F
CRCW06033092F
IHLP4040
0603
5.6µH, 0.018 Ohms, 16A
10kΩ, 1%
Vishay
Vishay
Vishay
Vishay
0603
49.9kΩ, 1%
R3
0603
30.9kΩ, 1%
22
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM20323
LM20323
www.ti.com
SNVS557C –MAY 2008–REVISED APRIL 2013
REVISION HISTORY
Changes from Revision B (April 2013) to Revision C
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 22
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: LM20323
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LM20323MH/NOPB
LM20323MHE/NOPB
LM20323MHX/NOPB
ACTIVE
ACTIVE
ACTIVE
HTSSOP
HTSSOP
HTSSOP
PWP
PWP
PWP
20
20
20
73
RoHS & Green
RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
20323MH
250
SN
SN
20323MH
20323MH
2500 RoHS & Green
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM20323MHE/NOPB
LM20323MHX/NOPB
HTSSOP PWP
HTSSOP PWP
20
20
250
178.0
330.0
16.4
16.4
6.95
6.95
7.1
7.1
1.6
1.6
8.0
8.0
16.0
16.0
Q1
Q1
2500
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM20323MHE/NOPB
LM20323MHX/NOPB
HTSSOP
HTSSOP
PWP
PWP
20
20
250
210.0
367.0
185.0
367.0
35.0
35.0
2500
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
TUBE
*All dimensions are nominal
Device
Package Name Package Type
PWP HTSSOP
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
LM20323MH/NOPB
20
73
495
8
2514.6
4.06
Pack Materials-Page 3
MECHANICAL DATA
PWP0020A
MXA20A (Rev C)
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号:
LM20323MHE/NOPB
IC 6 A SWITCHING REGULATOR, 570 kHz SWITCHING FREQ-MAX, PDSO20, LEAD FREE, TSSOP-20, Switching Regulator or Controller
NSC
©2020 ICPDF网 联系我们和版权申明