LM2577MX-12/NOPB [TI]
IC 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, PDSO24, 0.300 INCH, SO-24, Switching Regulator or Controller;型号: | LM2577MX-12/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | IC 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, PDSO24, 0.300 INCH, SO-24, Switching Regulator or Controller 开关 光电二极管 |
文件: | 总32页 (文件大小:1436K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
National Semiconductor is now part of
Texas Instruments.
Search http://www.ti.com/ for the latest technical
information and details on our current products and services.
April 2005
LM1577/LM2577
SIMPLE SWITCHER® Step-Up Voltage Regulator
General Description
Features
n Requires few external components
n NPN output switches 3.0A, can stand off 65V
n Wide input voltage range: 3.5V to 40V
n Current-mode operation for improved transient
response, line regulation, and current limit
n 52 kHz internal oscillator
The LM1577/LM2577 are monolithic integrated circuits that
provide all of the power and control functions for step-up
(boost), flyback, and forward converter switching regulators.
The device is available in three different output voltage
versions: 12V, 15V, and adjustable.
Requiring a minimum number of external components, these
regulators are cost effective, and simple to use. Listed in this
data sheet are a family of standard inductors and flyback
transformers designed to work with these switching regula-
tors.
n Soft-start function reduces in-rush current during start-up
n Output switch protected by current limit, under-voltage
lockout, and thermal shutdown
Included on the chip is a 3.0A NPN switch and its associated
protection circuitry, consisting of current and thermal limiting,
and undervoltage lockout. Other features include a 52 kHz
fixed-frequency oscillator that requires no external compo-
nents, a soft start mode to reduce in-rush current during
start-up, and current mode control for improved rejection of
input voltage and output load transients.
Typical Applications
n Simple boost regulator
n Flyback and forward regulators
n Multiple-output regulator
Connection Diagrams
Straight Leads
5-Lead TO-220 (T)
Bent, Staggered Leads
5-Lead TO-220 (T)
01146804
Top View
01146805
Top View
Order Number LM2577T-12, LM2577T-15,
or LM2577T-ADJ
Order Number LM2577T-12 Flow LB03, LM2577T-15
Flow LB03, or LM2577T-ADJ Flow LB03
See NS Package Number T05D
See NS Package Number T05A
SIMPLE SWITCHER® is a registered trademark of National Semiconductor Corporation.
© 2005 National Semiconductor Corporation
DS011468
www.national.com
Connection Diagrams (Continued)
16-Lead DIP (N)
24-Lead Surface Mount (M)
01146806
*No internal Connection
Top View
Order Number LM2577N-12, LM2577N-15,
or LM2577N-ADJ
See NS Package Number N16A
01146807
*No internal Connection
Top View
Order Number LM2577M-12, LM2577M-15,
or LM2577M-ADJ
See NS Package Number M24B
TO-263 (S)
5-Lead Surface-Mount Package
01146833
Side View
Order Number LM2577S-12, LM2577S-15,
or LM2577S-ADJ
01146832
See NS Package Number TS5B
Top View
4-Lead TO-3 (K)
01146808
Bottom View
Order Number LM1577K-12/883, LM1577K-15/883,
or LM1577K-ADJ/883
See NS Package Number K04A
www.national.com
2
Ordering Information
Temperature
Range
Package
Type
Output Voltage
15V
NSC
Package
Drawing
M24B
12V
ADJ
Package
−40˚C ≤ TA ≤ +125˚C
24-Pin Surface
Mount
LM2577M-12
LM2577M-15
LM2577M-ADJ
SO
16-Pin Molded DIP
5-Lead Surface
Mount
LM2577N-12
LM2577S-12
LM2577N-15
LM2577S-15
LM2577N-ADJ
LM2577S-ADJ
N16A
TS5B
N
TO-263
5-Straight Leads
5-Bent Staggered
Leads
LM2577T-12
LM2577T-12
Flow LB03
LM2577T-15
LM2577T-15
Flow LB03
LM2577T-ADJ
LM2577T-ADJ
Flow LB03
LM1577K-
T05A
T05D
TO-220
TO-220
−55˚C ≤ TA ≤ +150˚C
4-Pin TO-3
LM1577K-12/883LM1577K-15/883
K04A
TO-3
ADJ/883
Typical Application
01146801
Note: Pin numbers shown are for TO-220 (T) package.
3
www.national.com
Absolute Maximum Ratings (Note 1)
Minimum ESD Rating
(C = 100 pF, R = 1.5 kΩ)
2 kV
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Operating Ratings
Supply Voltage
Supply Voltage
45V
65V
3.5V ≤ VIN ≤ 40V
0V ≤ VSWITCH ≤ 60V
ISWITCH ≤ 3.0A
Output Switch Voltage
Output Switch Current (Note 2)
Power Dissipation
Output Switch Voltage
Output Switch Current
Junction Temperature Range
LM1577
6.0A
Internally Limited
−65˚C to +150˚C
Storage Temperature Range
Lead Temperature
−55˚C ≤ TJ ≤ +150˚C
−40˚C ≤ TJ ≤ +125˚C
LM2577
(Soldering, 10 sec.)
260˚C
150˚C
Maximum Junction Temperature
Electrical Characteristics—LM1577-12, LM2577-12
Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V, and ISWITCH = 0.
LM1577-12 LM2577-12
Units
Symbol
Parameter
Conditions
Typical
Limit
Limit
(Limits)
(Notes 3, 4)
(Note 5)
SYSTEM PARAMETERS Circuit of Figure 1 (Note 6)
VOUT
Output Voltage
VIN = 5V to 10V
12.0
V
ILOAD = 100 mA to 800 mA
(Note 3)
11.60/11.40 11.60/11.40
12.40/12.60 12.40/12.60
V(min)
V(max)
mV
Line Regulation
Load Regulation
Efficiency
VIN = 3.5V to 10V
20
20
ILOAD = 300 mA
50/100
50/100
50/100
50/100
mV(max)
mV
VIN = 5V
ILOAD = 100 mA to 800 mA
VIN = 5V, ILOAD = 800 mA
mV(max)
%
η
80
7.5
25
DEVICE PARAMETERS
IS
Input Supply Current
VFEEDBACK = 14V (Switch Off)
mA
mA(max)
mA
10.0/14.0
50/85
10.0/14.0
50/85
ISWITCH = 2.0A
VCOMP = 2.0V (Max Duty Cycle)
ISWITCH = 100 mA
mA(max)
V
VUV
Input Supply
2.90
Undervoltage Lockout
2.70/2.65
3.10/3.15
2.70/2.65
3.10/3.15
V(min)
V(max)
kHz
fO
Oscillator Frequency
Measured at Switch Pin
ISWITCH = 100 mA
52
48/42
56/62
48/42
56/62
kHz(min)
kHz(max)
V
VREF
Output Reference
Voltage
Measured at Feedback Pin
VIN = 3.5V to 40V
VCOMP = 1.0V
12
7
11.76/11.64 11.76/11.64
12.24/12.36 12.24/12.36
V(min)
V(max)
Output Reference
VIN = 3.5V to 40V
mV
Voltage Line Regulator
RFB
GM
Feedback Pin Input
Resistance
9.7
kΩ
Error Amp
ICOMP = −30 µA to +30 µA
VCOMP = 1.0V
370
µmho
Transconductance
225/145
515/615
225/145
515/615
µmho(min)
µmho(max)
www.national.com
4
Electrical Characteristics—LM1577-12, LM2577-12 (Continued)
Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V, and ISWITCH = 0.
LM1577-12 LM2577-12
Units
Symbol
Parameter
Conditions
Typical
Limit
Limit
(Limits)
(Notes 3, 4)
(Note 5)
DEVICE PARAMETERS
AVOL
Error Amp
VCOMP = 1.1V to 1.9V
RCOMP = 1.0 MΩ
(Note 7)
80
V/V
Voltage Gain
50/25
50/25
V/V(min)
Error Amplifier
Output Swing
Upper Limit
2.4
0.3
200
V
V(min)
V
VFEEDBACK = 10.0V
Lower Limit
2.2/2.0
2.2/2.0
VFEEDBACK = 15.0V
VFEEDBACK = 10.0V to 15.0V
VCOMP = 1.0V
0.40/0.55
0.40/0.55
V(max)
µA
Error Amplifier
Output Current
130/ 90
130/ 90
µA(min)
µA(max)
µA
300/ 400
300/ 400
ISS
Soft Start Current
VFEEDBACK = 10.0V
VCOMP = 0V
5.0
2.5/1.5
7.5/9.5
2.5/1.5
7.5/9.5
µA(min)
µA(max)
%
D
Maximum Duty Cycle
VCOMP = 1.5V
95
ISWITCH = 100 mA
93/90
93/90
%(min)
A/V
Switch
12.5
Transconductance
IL
Switch Leakage
Current
VSWITCH = 65V
10
0.5
4.5
µA
µA(max)
V
VFEEDBACK = 15V (Switch Off)
ISWITCH = 2.0A
300/600
0.7/0.9
300/600
0.7/0.9
VSAT
Switch Saturation
Voltage
VCOMP = 2.0V (Max Duty Cycle)
V(max)
A
NPN Switch
Current Limit
3.7/3.0
5.3/6.0
3.7/3.0
5.3/6.0
A(min)
A(max)
Electrical Characteristics—LM1577-15, LM2577-15
Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V, and ISWITCH = 0.
LM1577-15 LM2577-15
Units
Symbol
Parameter
Conditions
Typical
Limit
Limit
(Limits)
(Notes 3, 4)
(Note 5)
SYSTEM PARAMETERS Circuit of Figure 2 (Note 6)
VOUT
Output Voltage
VIN = 5V to 12V
15.0
V
ILOAD = 100 mA to 600 mA
(Note 3)
14.50/14.25 14.50/14.25
15.50/15.75 15.50/15.75
V(min)
V(max)
mV
Line Regulation
Load Regulation
Efficiency
VIN = 3.5V to 12V
20
20
80
50/100
50/100
50/100
50/100
ILOAD = 300 mA
mV(max)
mV
VIN = 5V
ILOAD = 100 mA to 600 mA
VIN = 5V, ILOAD = 600 mA
mV(max)
%
η
5
www.national.com
Electrical Characteristics—LM1577-15, LM2577-15 (Continued)
Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V, and ISWITCH = 0.
LM1577-15 LM2577-15
Units
Symbol
Parameter
Conditions
Typical
Limit
Limit
(Limits)
(Notes 3, 4)
(Note 5)
DEVICE PARAMETERS
IS
Input Supply Current
VFEEDBACK = 18.0V
(Switch Off)
7.5
25
mA
10.0/14.0
50/85
10.0/14.0
50/85
mA(max)
mA
ISWITCH = 2.0A
VCOMP = 2.0V
mA(max)
(Max Duty Cycle)
ISWITCH = 100 mA
VUV
Input Supply
Undervoltage
Lockout
2.90
52
V
V(min)
V(max)
kHz
2.70/2.65
3.10/3.15
2.70/2.65
3.10/3.15
fO
Oscillator Frequency
Measured at Switch Pin
ISWITCH = 100 mA
48/42
56/62
48/42
56/62
kHz(min)
kHz(max)
V
VREF
Output Reference
Voltage
Measured at Feedback Pin
VIN = 3.5V to 40V
VCOMP = 1.0V
15
10
14.70/14.55 14.70/14.55
15.30/15.45 15.30/15.45
V(min)
V(max)
mV
Output Reference
VIN = 3.5V to 40V
Voltage Line Regulation
RFB
GM
Feedback Pin Input
Voltage Line Regulator
Error Amp
12.2
300
kΩ
ICOMP = −30 µA to +30 µA
VCOMP = 1.0V
µmho
µmho(min)
µmho(max)
V/V
Transconductance
170/110
420/500
170/110
420/500
AVOL
Error Amp
VCOMP = 1.1V to 1.9V
RCOMP = 1.0 MΩ
(Note 7)
65
Voltage Gain
40/20
40/20
V/V(min)
Error Amplifier
Output Swing
Upper Limit
2.4
0.3
200
V
V(min)
V
VFEEDBACK = 12.0V
Lower Limit
2.2/2.0
2.2/2.0
VFEEDBACK = 18.0V
VFEEDBACK = 12.0V to 18.0V
VCOMP = 1.0V
0.4/0.55
0.40/0.55
V(max)
µA
Error Amp
Output Current
130/ 90
130/ 90
µA(min)
µA(max)
µA
300/ 400
300/ 400
ISS
Soft Start Current
VFEEDBACK = 12.0V
VCOMP = 0V
5.0
2.5/1.5
7.5/9.5
2.5/1.5
7.5/9.5
µA(min)
µA(max)
%
D
Maximum Duty
Cycle
VCOMP = 1.5V
95
ISWITCH = 100 mA
93/90
93/90
%(min)
A/V
Switch
12.5
Transconductance
IL
Switch Leakage
Current
VSWITCH = 65V
VFEEDBACK = 18.0V
(Switch Off)
10
µA
300/600
0.7/0.9
300/600
0.7/0.9
µA(max)
VSAT
Switch Saturation
Voltage
ISWITCH = 2.0A
VCOMP = 2.0V
(Max Duty Cycle)
0.5
V
V(max)
www.national.com
6
Electrical Characteristics—LM1577-15, LM2577-15 (Continued)
Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V, and ISWITCH = 0.
LM1577-15 LM2577-15
Units
Symbol
Parameter
Conditions
Typical
Limit
Limit
(Limits)
(Notes 3, 4)
(Note 5)
DEVICE PARAMETERS
NPN Switch
Current Limit
VCOMP = 2.0V
4.3
A
3.7/3.0
5.3/6.0
3.7/3.0
5.3/6.0
A(min)
A(max)
Electrical Characteristics—LM1577-ADJ, LM2577-ADJ
Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V, VFEEDBACK = VREF, and ISWITCH = 0.
LM1577-ADJ LM2577-ADJ
Units
Symbol
Parameter
Conditions
Typical
Limit
Limit
(Limits)
(Notes 3, 4)
(Note 5)
SYSTEM PARAMETERS Circuit of Figure 3 (Note 6)
VOUT
Output Voltage
VIN = 5V to 10V
12.0
V
V(min)
V(max)
mV
ILOAD = 100 mA to 800 mA
(Note 3)
11.60/11.40
12.40/12.60
11.60/11.40
12.40/12.60
∆VOUT
∆VIN
/
/
Line Regulation
Load Regulation
Efficiency
VIN = 3.5V to 10V
ILOAD = 300 mA
20
20
50/100
50/100
50/100
50/100
mV(max)
mV
∆VOUT
VIN = 5V
∆ILOAD
ILOAD = 100 mA to 800 mA
VIN = 5V, ILOAD = 800 mA
mV(max)
%
η
80
DEVICE PARAMETERS
IS
Input Supply Current
VFEEDBACK = 1.5V (Switch Off)
7.5
25
mA
mA(max)
mA
10.0/14.0
50/85
10.0/14.0
50/85
ISWITCH = 2.0A
VCOMP = 2.0V (Max Duty Cycle)
ISWITCH = 100 mA
mA(max)
V
VUV
Input Supply
2.90
Undervoltage Lockout
2.70/2.65
3.10/3.15
2.70/2.65
3.10/3.15
V(min)
V(max)
kHz
fO
Oscillator Frequency
Measured at Switch Pin
ISWITCH = 100 mA
52
48/42
56/62
48/42
56/62
kHz(min)
kHz(max)
V
VREF
Reference
Voltage
Measured at Feedback Pin
VIN = 3.5V to 40V
VCOMP = 1.0V
1.230
0.5
1.214/1.206
1.246/1.254
1.214/1.206
1.246/1.254
V(min)
V(max)
mV
∆VREF
∆VIN
IB
/
Reference Voltage
Line Regulation
Error Amp
VIN = 3.5V to 40V
VCOMP = 1.0V
100
nA
Input Bias Current
Error Amp
300/800
300/800
nA(max)
µmho
GM
ICOMP = −30 µA to +30 µA
VCOMP = 1.0V
3700
Transconductance
2400/1600
4800/5800
2400/1600
4800/5800
µmho(min)
µmho(max)
V/V
AVOL
Error Amp
VCOMP = 1.1V to 1.9V
800
Voltage Gain
RCOMP = 1.0 MΩ (Note 7)
500/250
500/250
V/V(min)
7
www.national.com
Electrical Characteristics—LM1577-ADJ, LM2577-ADJ (Continued)
Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 5V, VFEEDBACK = VREF, and ISWITCH = 0.
LM1577-ADJ LM2577-ADJ
Units
Symbol
Parameter
Conditions
Typical
Limit
Limit
(Limits)
(Notes 3, 4)
(Note 5)
DEVICE PARAMETERS
Error Amplifier
Upper Limit
2.4
0.3
200
V
V(min)
V
Output Swing
VFEEDBACK = 1.0V
Lower Limit
2.2/2.0
2.2/2.0
VFEEDBACK = 1.5V
VFEEDBACK = 1.0V to 1.5V
VCOMP = 1.0V
0.40/0.55
0.40/0.55
V(max)
µA
Error Amp
Output Current
130/ 90
130/ 90
µA(min)
µA(max)
µA
300/ 400
300/ 400
ISS
Soft Start Current
VFEEDBACK = 1.0V
VCOMP = 0V
5.0
2.5/1.5
7.5/9.5
2.5/1.5
7.5/9.5
µA(min)
µA(max)
%
D
Maximum Duty Cycle
VCOMP = 1.5V
95
12.5
10
ISWITCH = 100 mA
93/90
93/90
%(min)
A/V
∆ISWITCH
∆VCOMP
IL
/
Switch
Transconductance
Switch Leakage
Current
VSWITCH = 65V
µA
µA(max)
V
VFEEDBACK = 1.5V (Switch Off)
ISWITCH = 2.0A
300/600
0.7/0.9
300/600
0.7/0.9
VSAT
Switch Saturation
Voltage
0.5
4.3
VCOMP = 2.0V (Max Duty Cycle)
VCOMP = 2.0V
V(max)
A
NPN Switch
Current Limit
3.7/3.0
5.3/6.0
3.7/3.0
5.3/6.0
A(min)
A(max)
THERMAL PARAMETERS (All Versions)
θJA
θJC
θJA
θJC
θJA
Thermal Resistance
K Package, Junction to Ambient
K Package, Junction to Case
T Package, Junction to Ambient
T Package, Junction to Case
N Package, Junction to
Ambient (Note 8)
35
1.5
65
2
85
˚C/W
θJA
θJA
M Package, Junction
100
37
to Ambient (Note 8)
S Package, Junction to
Ambient (Note 9)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions the device is intended to
be functional, but device parameter specifications may not be guaranteed under these conditions. For guaranteed specifications and test conditions, see the
Electrical Characteristics.
Note 2: Due to timing considerations of the LM1577/LM2577 current limit circuit, output current cannot be internally limited when the LM1577/LM2577 is used as
a step-up regulator. To prevent damage to the switch, its current must be externally limited to 6.0A. However, output current is internally limited when the
LM1577/LM2577 is used as a flyback or forward converter regulator in accordance to the Application Hints.
Note 3: All limits guaranteed at room temperature (standard type face) and at temperature extremes (boldface type). All limits are used to calculate Outgoing Quality
Level, and are 100% production tested.
Note 4: A military RETS electrical test specification is available on request. At the time of printing, the LM1577K-12/883, LM1577K-15/883, and LM1577K-ADJ/883
RETS specifications complied fully with the boldface limits in these columns. The LM1577K-12/883, LM1577K-15/883, and LM1577K-ADJ/883 may also be procured
to Standard Military Drawing specifications.
Note 5: All limits guaranteed at room temperature (standard type face) and at temperature extremes (boldface type). All room temperature limits are 100%
production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods.
Note 6: External components such as the diode, inductor, input and output capacitors can affect switching regulator performance. When the LM1577/LM2577 is
used as shown in the Test Circuit, system performance will be as specified by the system parameters.
Note 7: A 1.0 MΩ resistor is connected to the compensation pin (which is the error amplifier’s output) to ensure accuracy in measuring A
. In actual applications,
VOL
this pin’s load resistance should be ≥10 MΩ, resulting in A
that is typically twice the guaranteed minimum limit.
VOL
www.national.com
8
Electrical Characteristics—LM1577-ADJ, LM2577-ADJ (Continued)
Note 8: Junction to ambient thermal resistance with approximately 1 square inch of pc board copper surrounding the leads. Additional copper area will lower thermal
resistance further. See thermal model in “Switchers Made Simple” software.
Note 9: If the TO-263 package is used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the package. Using
0.5 square inches of copper area, θ is 50˚C/W; with 1 square inch of copper area, θ is 37˚C/W; and with 1.6 or more square inches of copper area, θ is 32˚C/W.
JA
JA
JA
Typical Performance Characteristics
Reference Voltage
vs Temperature
Reference Voltage
vs Temperature
01146834
01146835
01146837
01146839
Reference Voltage
vs Temperature
∆ Reference Voltage
vs Supply Voltage
01146836
∆ Reference Voltage
vs Supply Voltage
∆ Reference Voltage
vs Supply Voltage
01146838
9
www.national.com
Typical Performance Characteristics (Continued)
Error Amp Transconductance
vs Temperature
Error Amp Transconductance
vs Temperature
01146840
01146841
Error Amp Transconductance
vs Temperature
Error Amp Voltage
Gain vs Temperature
01146843
01146842
Error Amp Voltage
Error Amp Voltage
Gain vs Temperature
Gain vs Temperature
01146844
01146845
www.national.com
10
Typical Performance Characteristics (Continued)
Quiescent Current
vs Temperature
Quiescent Current
vs Switch Current
01146846
01146847
01146849
01146851
Current Limit
vs Temperature
Current Limit Response
Time vs Overdrive
01146848
Switch Saturation Voltage
vs Switch Current
Switch Transconductance
vs Temperature
01146850
11
www.national.com
Typical Performance Characteristics (Continued)
Feedback Pin Bias
Current vs Temperature
Oscillator Frequency
vs Temperature
01146852
01146853
Maximum Power Dissipation
(TO-263) (Note 9)
01146831
www.national.com
12
LM1577-12, LM2577-12 Test Circuit
01146830
L = 415-0930 (AIE)
D = any manufacturer
C
OUT
= Sprague Type 673D
Electrolytic 680 µF, 20V
Note: Pin numbers shown are for TO-220 (T) package
FIGURE 1. Circuit Used to Specify System Parameters for 12V Versions
LM1577-15, LM2577-15 Test Circuit
01146826
L = 415-0930 (AIE)
D = any manufacturer
C
OUT
= Sprague Type 673D
Electrolytic 680 µF, 20V
Note: Pin numbers shown are for TO-220 (T) package
FIGURE 2. Circuit Used to Specify System Parameters for 15V Versions
13
www.national.com
LM1577-ADJ, LM2577-ADJ Test Circuit
01146809
L = 415-0930 (AIE)
D = any manufacturer
C
OUT
= Sprague Type 673D
Electrolytic 680 µF, 20V
R1 = 48.7k in series with 511Ω (1%)
R2 = 5.62k (1%)
Note: Pin numbers shown are for TO-220 (T) package
FIGURE 3. Circuit Used to Specify System Parameters for ADJ Versions
Application Hints
01146810
Note: Pin numbers shown are for TO-220 (T) package
*Resistors are internal to LM1577/LM2577 for 12V and 15V versions.
FIGURE 4. LM1577/LM2577 Block Diagram and Boost Regulator Application
www.national.com
14
Application Hints (Continued)
STEP-UP (BOOST) REGULATOR
Duty Cycle
D
Figure 4 shows the LM1577-ADJ/LM2577-ADJ used as a
Step-Up Regulator. This is a switching regulator used for
producing an output voltage greater than the input supply
voltage. The LM1577-12/LM2577-12 and LM1577-15/
LM2577-15 can also be used for step-up regulators with 12V
or 15V outputs (respectively), by tying the feedback pin
directly to the regulator output.
Average
Inductor
IIND(AVE)
Current
Inductor
∆IIND
Current Ripple
Peak Inductor
Current
A basic explanation of how it works is as follows. The
LM1577/LM2577 turns its output switch on and off at a
frequency of 52 kHz, and this creates energy in the inductor
(L). When the NPN switch turns on, the inductor current
charges up at a rate of VIN/L, storing current in the inductor.
When the switch turns off, the lower end of the inductor flies
above VIN, discharging its current through diode (D) into the
output capacitor (COUT) at a rate of (VOUT − VIN)/L. Thus,
energy stored in the inductor during the switch on time is
transferred to the output during the switch off time. The
output voltage is controlled by the amount of energy trans-
ferred which, in turn, is controlled by modulating the peak
inductor current. This is done by feeding back a portion of
the output voltage to the error amp, which amplifies the
difference between the feedback voltage and a 1.230V ref-
erence. The error amp output voltage is compared to a
voltage proportional to the switch current (i.e., inductor cur-
rent during the switch on time).
IIND(PK)
Peak Switch
Current
ISW(PK)
Switch
Voltage When VSW(OFF)
VOUT + VF
Off
Diode
Reverse
VR
VOUT − VSAT
Voltage
Average
ID(AVE)
ID(PK)
ILOAD
Diode Current
Peak Diode
Current
Power
The comparator terminates the switch on time when the two
voltages are equal, thereby controlling the peak switch cur-
rent to maintain a constant output voltage.
Dissipation of
LM1577/2577
PD
V
= Forward Biased Diode Voltage
F
Voltage and current waveforms for this circuit are shown in
Figure 5, and formulas for calculating them are given in
Figure 6.
I
= Output Load Current
LOAD
FIGURE 6. Step-Up Regulator Formulas
STEP-UP REGULATOR DESIGN PROCEDURE
The following design procedure can be used to select the
appropriate external components for the circuit in Figure 4,
based on these system requirements.
Given:
VIN (min) = Minimum input supply voltage
VOUT = Regulated output voltage
ILOAD(max) = Maximum output load current
Before proceeding any further, determine if the LM1577/
LM2577 can provide these values of VOUT and ILOAD(max)
when operating with the minimum value of VIN. The upper
limits for VOUT and ILOAD(max) are given by the following
equations.
VOUT ≤ 60V
01146811
and VOUT ≤ 10 x VIN(min)
FIGURE 5. Step-Up Regulator Waveforms
These limits must be greater than or equal to the values
specified in this application.
1. Inductor Selection (L)
A. Voltage Options:
1. For 12V or 15V output
From Figure 7 (for 12V output) or Figure 8 (for 15V
output), identify inductor code for region indicated by
VIN (min) and ILOAD (max). The shaded region indicates con-
15
www.national.com
1. Find the lowest value inductor that is greater than LMIN
.
Application Hints (Continued)
2. Find where E•T intersects this inductor value to determine
if it has an L or H prefix. If E•T intersects both the L and H
regions, select the inductor with an H prefix.
ditions for which the LM1577/LM2577 output switch
would be operating beyond its switch current rating. The
minimum operating voltage for the LM1577/LM2577 is
3.5V.
From here, proceed to step C.
2. For Adjustable version
Preliminary calculations:
The inductor selection is based on the calculation of the
following three parameters:
D(max), the maximum switch duty cycle (0 ≤ D ≤ 0.9):
where VF = 0.5V for Schottky diodes and 0.8V for fast
recovery diodes (typically);
E •T, the product of volts x time that charges the inductor:
01146827
FIGURE 7. LM2577-12 Inductor Selection Guide
IIND,DC, the average inductor current under full load;
B. Identify Inductor Value:
1. From Figure 9, identify the inductor code for the
region indicated by the intersection of E•T and IIND,DC
.
This code gives the inductor value in microhenries. The
L or H prefix signifies whether the inductor is rated for a
maximum E•T of 90 V•µs (L) or 250 V•µs (H).
<
2. If D 0.85, go on to step C. If D ≥ 0.85, then calculate
the minimum inductance needed to ensure the switching
regulator’s stability:
01146828
FIGURE 8. LM2577-15 Inductor Selection Guide
If LMIN is smaller than the inductor value found in step B1, go
on to step C. Otherwise, the inductor value found in step B1
is too low; an appropriate inductor code should be obtained
from the graph as follows:
www.national.com
16
Application Hints (Continued)
01146812
Note: These charts assume that the inductor ripple current inductor is approximately 20% to 30% of the average inductor current (when the regulator is under
full load). Greater ripple current causes higher peak switch currents and greater output ripple voltage; lower ripple current is achieved with larger-value
inductors. The factor of 20 to 30% is chosen as a convenient balance between the two extremes.
FIGURE 9. LM1577-ADJ/LM2577-ADJ Inductor Selection Graph
C. Select an inductor from the table of Figure 10 which
cross-references the inductor codes to the part numbers
of three different manufacturers. Complete specifications
for these inductors are available from the respective
manufacturers. The inductors listed in this table have the
following characteristics:
AIE: ferrite, pot-core inductors; Benefits of this type are
low electro-magnetic interference (EMI), small physical
size, and very low power dissipation (core loss). Be
careful not to operate these inductors too far beyond their
maximum ratings for E•T and peak current, as this will
saturate the core.
Pulse: powdered iron, toroid core inductors; Benefits are
low EMI and ability to withstand E•T and peak current
above rated value better than ferrite cores.
Renco: ferrite, bobbin-core inductors; Benefits are low
cost and best ability to withstand E•T and peak current
above rated value. Be aware that these inductors gener-
ate more EMI than the other types, and this may interfere
with signals sensitive to noise.
17
www.national.com
C. Calculate the minimum value of CC
.
Application Hints (Continued)
Inductor
Code
L47
Manufacturer’s Part Number
Schott
Pulse
Renco
RL2442
RL2443
RL2444
RL1954
RL1953
RL1952
RL1951
RL1950
RL2445
RL2446
RL2447
RL1961
RL1960
RL1959
RL1958
RL2448
67126980
67126990
67127000
67127010
67127020
67127030
67127040
67127050
67127060
67127070
67127080
67127090
67127100
67127110
67127120
67127130
PE - 53112
PE - 92114
PE - 92108
PE - 53113
PE - 52626
PE - 52627
PE - 53114
PE - 52629
PE - 53115
PE - 53116
PE - 53117
PE - 53118
PE - 53119
PE - 53120
PE - 53121
PE - 53122
The compensation capacitor is also part of the soft start
circuitry. When power to the regulator is turned on, the
switch duty cycle is allowed to rise at a rate controlled by this
capacitor (with no control on the duty cycle, it would imme-
diately rise to 90%, drawing huge currents from the input
power supply). In order to operate properly, the soft start
circuit requires CC ≥ 0.22 µF.
The value of the output filter capacitor is normally large
enough to require the use of aluminum electrolytic capaci-
tors. Figure 11 lists several different types that are recom-
mended for switching regulators, and the following param-
eters are used to select the proper capacitor.
L68
L100
L150
L220
L330
L470
L680
H150
H220
H330
H470
H680
H1000
H1500
H2200
Working Voltage (WVDC): Choose a capacitor with a work-
ing voltage at least 20% higher than the regulator output
voltage.
Ripple Current: This is the maximum RMS value of current
that charges the capacitor during each switching cycle. For
step-up and flyback regulators, the formula for ripple current
is
Schott Corp., (612) 475-1173
1000 Parkers Lake Rd., Wayzata, MN 55391
Pulse Engineering, (619) 268-2400
P.O. Box 12235, San Diego, CA 92112
Renco Electronics Inc., (516) 586-5566
60 Jeffryn Blvd. East, Deer Park, NY 11729
Choose a capacitor that is rated at least 50% higher than this
value at 52 kHz.
FIGURE 10. Table of Standardized Inductors and
Manufacturer’s Part Numbers
Equivalent Series Resistance (ESR) : This is the primary
cause of output ripple voltage, and it also affects the values
of RC and CC needed to stabilize the regulator. As a result,
the preceding calculations for CC and RC are only valid if
ESR doesn’t exceed the maximum value specified by the
following equations.
2. Compensation Network (RC, CC) and Output Capacitor
(COUT) Selection
RC and CC form a pole-zero compensation network that
stabilizes the regulator. The values of RC and CC are mainly
dependant on the regulator voltage gain, ILOAD(max), L and
COUT. The following procedure calculates values for RC, CC,
and COUT that ensure regulator stability. Be aware that this
procedure doesn’t necessarily result in RC and CC that pro-
vide optimum compensation. In order to guarantee optimum
compensation, one of the standard procedures for testing
loop stability must be used, such as measuring VOUT tran-
sient response when pulsing ILOAD (see Figure 15).
Select a capacitor with ESR, at 52 kHz, that is less than or
equal to the lower value calculated. Most electrolytic capaci-
tors specify ESR at 120 Hz which is 15% to 30% higher than
at 52 kHz. Also, be aware that ESR increases by a factor of
2 when operating at −20˚C.
A. First, calculate the maximum value for RC.
In general, low values of ESR are achieved by using large
value capacitors (C ≥ 470 µF), and capacitors with high
WVDC, or by paralleling smaller-value capacitors.
Select a resistor less than or equal to this value, and it
should also be no greater than 3 kΩ.
B. Calculate the minimum value for COUT using the following
The larger of these two values is the minimum value that
ensures stability.
www.national.com
18
Application Hints (Continued)
3. Output Voltage Selection (R1 and R2)
If the LM1577 is located far from the supply source filter
capacitors, an additional large electrolytic capacitor (e.g.
47 µF) is often required.
This section is for applications using the LM1577-ADJ/
LM2577-ADJ. Skip this section if the LM1577-12/LM2577-12
or LM1577-15/LM2577-15 is being used.
5. Diode Selection (D)
The switching diode used in the boost regulator must with-
stand a reverse voltage equal to the circuit output voltage,
and must conduct the peak output current of the LM2577. A
suitable diode must have a minimum reverse breakdown
voltage greater than the circuit output voltage, and should be
rated for average and peak current greater than ILOAD(max)
and ID(PK). Schottky barrier diodes are often favored for use
in switching regulators. Their low forward voltage drop allows
higher regulator efficiency than if a (less expensive) fast
recovery diode was used. See Figure 12 for recommended
part numbers and voltage ratings of 1A and 3A diodes.
With the LM1577-ADJ/LM2577-ADJ, the output voltage is
given by
VOUT = 1.23V (1 + R1/R2)
Resistors R1 and R2 divide the output down so it can be
compared with the LM1577-ADJ/LM2577-ADJ internal
1.23V reference. For a given desired output voltage VOUT
,
select R1 and R2 so that
VOUT
(max)
20V
Schottky
Fast Recovery
4. Input Capacitor Selection (CIN
)
1A
1N5817
3A
1A
3A
The switching action in the step-up regulator causes a trian-
gular ripple current to be drawn from the supply source. This
in turn causes noise to appear on the supply voltage. For
proper operation of the LM1577, the input voltage should be
decoupled. Bypassing the Input Voltage pin directly to
ground with a good quality, low ESR, 0.1 µF capacitor (leads
as short as possible) is normally sufficient.
1N5820
MBR120P MBR320P
1N5818 1N5821
MBR130P MBR330P
30V
40V
11DQ03
1N5819
31DQ03
1N5822
MBR140P MBR340P
Cornell Dublier —Types 239, 250, 251, UFT,
300, or 350
11DQ04
MBR150
11DQ05
31DQ04
MBR350
31DQ05
1N4933
MUR105
1N4934
HER102
MUR110
10DL1
P.O. Box 128, Pickens, SC 29671
(803) 878-6311
50V
Nichicon —Types PF, PX, or PZ
927 East Parkway,
MR851
30DL1
100V
Schaumburg, IL 60173
MR831
HER302
(708) 843-7500
Sprague —Types 672D, 673D, or 674D
Box 1, Sprague Road,
FIGURE 12. Diode Selection Chart
Lansing, NC 28643
(919) 384-2551
BOOST REGULATOR CIRCUIT EXAMPLE
United Chemi-Con —Types LX, SXF, or SXJ
9801 West Higgins Road,
Rosemont, IL 60018
By adding a few external components (as shown in Figure
13), the LM2577 can be used to produce a regulated output
voltage that is greater than the applied input voltage. Typical
performance of this regulator is shown in Figure 14 and
Figure 15. The switching waveforms observed during the
operation of this circuit are shown in Figure 16.
(708) 696-2000
FIGURE 11. Aluminum Electrolytic Capacitors
Recommended for Switching Regulators
19
www.national.com
Application Hints (Continued)
01146813
Note: Pin numbers shown are for TO-220 (T) package.
FIGURE 13. Step-up Regulator Delivers 12V from a 5V Input
01146814
FIGURE 14. Line Regulation (Typical) of Step-Up Regulator of Figure 13
01146816
A: Switch pin voltage, 10 V/div
01146815
B: Switch pin current, 2 A/div
C: Inductor current, 2 A/div
A: Output Voltage Change, 100 mV/div. (AC-coupled)
B: Load current, 0.2 A/div
D: Output ripple voltage, 100 mV/div (AC-coupled)
Horizontal: 5 µs/div
Horizontal: 5 ms/div
FIGURE 15. Load Transient Response of Step-Up
FIGURE 16. Switching Waveforms of Step-Up
Regulator of Figure 13
Regulator of Figure 13
www.national.com
20
A. First, calculate the maximum value for RC.
Application Hints (Continued)
FLYBACK REGULATOR
A Flyback regulator can produce single or multiple output
voltages that are lower or greater than the input supply
voltage. Figure 18 shows the LM1577/LM2577 used as a
flyback regulator with positive and negative regulated out-
puts. Its operation is similar to a step-up regulator, except the
output switch contols the primary current of a flyback trans-
former. Note that the primary and secondary windings are
out of phase, so no current flows through secondary when
current flows through the primary. This allows the primary to
charge up the transformer core when the switch is on. When
the switch turns off, the core discharges by sending current
through the secondary, and this produces voltage at the
outputs. The output voltages are controlled by adjusting the
peak primary current, as described in the step-up regulator
section.
∑
Where ILOAD(max) is the sum of the load current (magni-
tude) required from both outputs. Select a resistor less than
or equal to this value, and no greater than 3 kΩ.
B. Calculate the minimum value for COUT (sum of COUT
at both outputs) using the following two equations.
∑
Voltage and current waveforms for this circuit are shown in
Figure 17, and formulas for calculating them are given in
Figure 19.
The larger of these two values must be used to ensure
regulator stability.
FLYBACK REGULATOR DESIGN PROCEDURE
1. Transformer Selection
A family of standardized flyback transformers is available for
creating flyback regulators that produce dual output volt-
ages, from 10V to 15V, as shown in Figure 18. Figure
20lists these transformers with the input voltage, output
voltages and maximum load current they are designed for.
2. Compensation Network (CC, RC) and
Output Capacitor (COUT) Selection
As explained in the Step-Up Regulator Design Procedure,
CC, RC and COUT must be selected as a group. The following
procedure is for a dual output flyback regulator with equal
turns ratios for each secondary (i.e., both output voltages
have the same magnitude). The equations can be used for a
01146817
FIGURE 17. Flyback Regulator Waveforms
∑
single output regulator by changing ILOAD(max) to ILOAD(max)
in the following equations.
21
www.national.com
Application Hints (Continued)
01146818
T1 = Pulse Engineering, PE-65300
D1, D2 = 1N5821
FIGURE 18. LM1577-ADJ/LM2577-ADJ Flyback Regulator with Outputs
www.national.com
22
Application Hints (Continued)
Duty Cycle
D
Primary Current Variation
Peak Primary Current
Switch Voltage when Off
∆IP
IP(PK)
VSW(OFF)
+
−
Diode Reverse Voltage
Average Diode Current
Peak Diode Current
VR
VOUT N (VIN VSAT
)
ID(AVE)
ILOAD
ID(PK)
Short Circuit Diode Current
Power Dissipation of
LM1577/LM2577
PD
01146878
FIGURE 19. Flyback Regulator Formulas
C. Calculate the minimum value of CC
VOUT = 1.23V (1 + R1/R2)
Resistors R1 and R2 divide the output voltage down so it can
be compared with the LM1577-ADJ/LM2577-ADJ internal
1.23V reference. For a desired output voltage VOUT, select
R1 and R2 so that
D. Calculate the maximum ESR of the +VOUT and −VOUT
output capacitors in parallel.
4. Diode Selection
The switching diode in a flyback converter must withstand
the reverse voltage specified by the following equation.
This formula can also be used to calculate the maximum
ESR of a single output regulator.
At this point, refer to this same section in the Step-Up
Regulator Design Procedurefor more information regard-
ing the selection of COUT
.
A suitable diode must have a reverse voltage rating greater
than this. In addition it must be rated for more than the
average and peak diode currents listed in Figure 19.
3. Output Voltage Selection
This section is for applications using the LM1577-ADJ/
LM2577-ADJ. Skip this section if the LM1577-12/LM2577-12
or LM1577-15/LM2577-15 is being used.
5. Input Capacitor Selection
The primary of a flyback transformer draws discontinuous
pulses of current from the input supply. As a result, a flyback
regulator generates more noise at the input supply than a
With the LM1577-ADJ/LM2577-ADJ, the output voltage is
given by
23
www.national.com
ber consists of a fast recovery diode, and a parallel RC. The
RC values are selected for switch clamp voltage (VCLAMP
Application Hints (Continued)
)
step-up regulator, and this requires a larger bypass capacitor
to decouple the LM1577/LM2577 VIN pin from this noise. For
most applications, a low ESR, 1.0 µF cap will be sufficient, if
it is connected very close to the VIN and Ground pins.
that is 5V to 10V greater than VSW(OFF). Use the following
equations to calculate R and C;
Transformer
Type
Input
Dual
Output
Voltage
10V
Maximum
Output
Current
325 mA
275 mA
225 mA
700 mA
575 mA
500 mA
800 mA
700 mA
575 mA
900 mA
825 mA
700 mA
Voltage
LP = 100 µH
N = 1
5V
1
2
3
5V
12V
Power dissipation (and power rating) of the resistor is;
The fast recovery diode must have a reverse voltage rating
5V
15V
10V
10V
10V
12V
12V
12V
15V
15V
15V
10V
12V
LP = 200 µH
N = 0.5
15V
10V
greater than VCLAMP
.
12V
15V
LP = 250 µH
N = 0.5
10V
12V
15V
Transformer
Manufacturers’ Part Numbers
Type
AIE
Pulse
Renco
RL-2580
RL-2581
RL-2582
1
2
3
326-0637
330-0202
330-0203
PE-65300
PE-65301
PE-65302
FIGURE 20. Flyback Transformer Selection Guide
In addition to this bypass cap, a larger capacitor (≥ 47 µF)
should be used where the flyback transformer connects to
the input supply. This will attenuate noise which may inter-
fere with other circuits connected to the same input supply
voltage.
01146819
FIGURE 21. Snubber Circuit
FLYBACK REGULATOR CIRCUIT EXAMPLE
6. Snubber Circuit
The circuit of Figure 22 produces 15V (at 225 mA each)
from a single 5V input. The output regulation of this circuit is
shown in Figure 23 and Figure 25, while the load transient
response is shown in Figure 24 and Figure 26. Switching
waveforms seen in this circuit are shown in Figure 27.
A “snubber” circuit is required when operating from input
voltages greater than 10V, or when using a transformer with
LP ≥ 200 µH. This circuit clamps a voltage spike from the
transformer primary that occurs immediately after the output
switch turns off. Without it, the switch voltage may exceed
the 65V maximum rating. As shown in Figure 21, the snub-
www.national.com
24
Application Hints (Continued)
01146820
T1 = Pulse Engineering, PE-65300
D1, D2 = 1N5821
FIGURE 22. Flyback Regulator Easily Provides Dual Outputs
01146823
A: Output Voltage Change, 100 mV/div
B: Output Current, 100 mA/div
Horizontal: 10 ms/div
01146821
FIGURE 23. Line Regulation (Typical) of Flyback
FIGURE 24. Load Transient Response of Flyback
Regulator of Figure 22, +15V Output
Regulator of Figure 22, +15V Output
25
www.national.com
Application Hints (Continued)
01146824
A: Output Voltage Change, 100 mV/div
B: Output Current, 100 mA/div
Horizontal: 10 ms/div
FIGURE 26. Load Transient Response of Flyback
01146822
Regulator of Figure 22, −15V Output
FIGURE 25. Line Regulation (Typical) of Flyback
Regulator of Figure 22, −15V Output
01146825
A: Switch pin voltage, 20 V/div
B: Primary current, 2 A/div
C: +15V Secondary current, 1 A/div
D: +15V Output ripple voltage, 100 mV/div
Horizontal: 5 µs/div
FIGURE 27. Switching Waveforms of Flyback Regulator of Figure 22, Each Output Loaded with 60Ω
www.national.com
26
Physical Dimensions inches (millimeters)
unless otherwise noted
TO-3 Metal Can Package (K)
Order Number LM1577K-12/883, LM1577K-15/883, or LM1577K-ADJ/883
NS Package Number K04A
0.300 Wide SO Package (M)
Order Number LM2577M-12, LM2577M-15 or LM2577M-ADJ
NS Package Number M24B
27
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Molded Dual-In-Line Package (N)
Order Number LM2577N-12, LM2577N-15, or LM2577N-ADJ
NS Package Number N16A
TO-220, Straight Leads (T)
Order Number LM2577T-12, LM2577T-15, or LM2577T-ADJ
NS Package Number TO5A
www.national.com
28
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
TO-220, Bent Staggered Leads (T)
Order Number LM2577T-12 Flow LB03, LM2577T-15 Flow LB03, or LM2577T-ADJ Flow LB03
NS Package Number T05D
29
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
5-Lead TO-263 (S)
Order Number LM2577S-12, LM2577S-15 or LM2577S-ADJ
NS Package Number TS5B
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
www.national.com
Tel: 81-3-5639-7560
相关型号:
©2020 ICPDF网 联系我们和版权申明