LM340LAZ-5.0/LFT4 [TI]
100mA、35V 线性稳压器 | LP | 3;
| 型号： | LM340LAZ-5.0/LFT4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 100mA、35V 线性稳压器 | LP | 3 输出元件 稳压器 调节器 |
| 文件： | 总14页 (文件大小：406K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM140L, LM340L
www.ti.com
SNVS758B –APRIL 1998–REVISED MARCH 2013
LM140L/LM340L Series 3-Terminal Positive Regulators
Check for Samples: LM140L, LM340L
1
FEATURES
The LM140LA/LM340LA are available in the low
2
•
•
•
Line Regulation of 0.04%/V
Load Regulation of 0.01%/mA
Output Voltage Tolerances of
profile metal three lead TO (NDT) and the LM340LA
are also available in the plastic TO-92 (LP). With
adequate heat sinking the regulator can deliver 100
mA output current. Current limiting is included to limit
the peak output current to a safe value. Safe area
protection for the output transistor is provided to limit
internal power dissipation. If internal power
dissipation becomes too high for the heat sinking
provided, the thermal shut-down circuit takes over,
preventing the IC from overheating.
–
±2% at Tj = 25°C and ±4% Over the
Temperature Range (LM140LA)
–
±3% Over the Temperature Range
(LM340LA)
•
•
•
•
•
Output Current of 100 mA
Internal Thermal Overload Protection
Output Transistor Safe Area Protection
Internal Short Circuit Current Limit
Available in
For applications requiring other voltages, see LM117L
Data Sheet.
Output Voltage Options
–
Metal TO Low Profile Package
(LM140LA/LM340LA)
LM140LA-5.0
LM140LA-12
LM140LA-15
5V
LM340LA-5.0
LM340LA-12
LM340LA-15
5V
12V
15V
12V
15V
–
Plastic TO-92 (LM340LA)
DESCRIPTION
The LM140L series of three terminal positive
regulators is available with several fixed output
voltages making them useful in a wide range of
applications. The LM140LA is an improved version of
the LM78LXX series with a tighter output voltage
tolerance (specified over the full military temperature
range), higher ripple rejection, better regulation and
lower quiescent current. The LM140LA regulators
have ±2% VOUT specification, 0.04%/V line regulation,
and 0.01%/mA load regulation. When used as a
zener diode/resistor combination replacement, the
LM140LA usually results in an effective output
impedance improvement of two orders of magnitude,
and lower quiescent current. These regulators can
provide local on card regulation, eliminating the
distribution problems associated with single point
regulation. The voltages available allow the LM140LA
to be used in logic systems, instrumentation, Hi-Fi,
and other solid state electronic equipment. Although
designed primarily as fixed voltage regulators, these
devices can be used with external components to
obtain adjustable voltages and currents.
Connection Diagrams
Figure 1. TO Metal Can Package (NDT)
(Bottom View)
Figure 2. TO-92 Plastic Package (LP)
(Bottom View)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1998–2013, Texas Instruments Incorporated
LM140L, LM340L
SNVS758B –APRIL 1998–REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)(3)
Input Voltage
Internal Power Dissipation(4)
35V
Internally Limited
−55°C to +125°C
0°C to +70°C
+150°C
LM140LA
LM340LA
Operating Temperature Range
Maximum Junction Temperature
Storage Temperature Range
Metal Can (NDT package)
Molded TO-92
−65°C to +150°C
−55°C to +150°C
+300°C
Metal Can
Lead Temperature (Soldering, 10 sec.)
Plastic TO-92
+230°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits.
(2) A military RETS specification is available upon request. At the time of printing, the LM140LA-5.0, -12, and -15 RETS specifications
complied with the Min and Max limits in this table. The LM140LAH-5.0, LM140LAH-12, and LM140LAH-15 may also be procured as
Standard Military Drawings.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(4) Thermal resistance of NDT-package is typically 26°C/W θjC, 250°C/W θjA still air, and 94°C/W θjA 400 lf/min of air. For the LP-package is
60°C/W θjC, 232°C/W θjA still air, and 88°C/W θjA at 400 lf/min of air. The maximum junction temperature shall not exceed 125°C on
electrical parameters.
Electrical Characteristics
Test conditions unless otherwise specified. TA = −55°C to +125°C (LM140LA), TA = 0°C to +70°C (LM340LA), IO = 40 mA, CIN
= 0.33 μF, CO = 0.01 μF.
Output Voltage Option
5.0V
10V
Typ
5
12V
19V
Typ
12
15V
23V
Typ
15
Input Voltage (unless otherwise noted)
Units
Symbol
Parameter
Conditions
Min
Max
Min
Max
Min
Max
VO
Output
Tj = 25°C
4.9
5.1
11.75
12.25 14.7
15.3
Voltage
LM140LA IO = 1 − 100 mA
4.8
5.2
11.5
12.5
14.4
15.6
(7.2–20)
(7–20)
(14.5–27)
(14.3–27)
(17.6–30)
(17.5–30)
V
Output
Voltage Over LM340LA IO = 1 − 100 mA or
4.85
5.15 11.65
12.35 14.55
15.45
Temp.(1)
IO = 1 − 40 mA and
VIN = ( )V
ΔVO
Tj = 25°C IO = 40 mA
18
(7–25)
18
30
30
30
(14.2–30)
30
65
65
37
(17.3–30)
37
70
70
VIN = ( )V
IO = 100 mA
Line
Regulation
mV
VIN = ( )V
(7.5–25)
5
(14.5–30)
10
(17.5–30)
12
Tj = 25°C IO = 1 − 40 mA
IO = 1 − 100 mA
20
40
40
80
50
Load
Regulation
20
30
35
100
mV
1000
hrs
Long Term
Stability
12
3
24
3
30
IO
Tj = 25°C
4.5
4.2
0.1
4.5
4.2
0.1
3.1
4.5
4.2
0.1
Quiescent
Current
mA
Tj = 125°C
ΔIQ
Tj = 25°C ΔLoad IO = 1 − 40
Quiescent
Current
mA
mA
ΔLine VIN = ( )V
0.5
0.5
0.5
Change
(7.5–25)
(14.3–30)
(17.5–30)
(1) The temperature coefficient of VOUT is typically within 0.01% VO/°C.
Submit Documentation Feedback
2
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM140L LM340L
LM140L, LM340L
www.ti.com
SNVS758B –APRIL 1998–REVISED MARCH 2013
Electrical Characteristics (continued)
Test conditions unless otherwise specified. TA = −55°C to +125°C (LM140LA), TA = 0°C to +70°C (LM340LA), IO = 40 mA, CIN
= 0.33 μF, CO = 0.01 μF.
Output Voltage Option
5.0V
10V
Typ
12V
19V
Typ
15V
23V
Typ
Input Voltage (unless otherwise noted)
Units
Symbol
Parameter
Conditions
Min
Max
Min
Max
Min
Max
VN
Output Noise Tj = 25°C(2), f = 10 Hz–10 kHz
Voltage
40
80
90
μV
f = 120 Hz, VIN = ( )V
55
62
47
54
45
52
ΔVIN
Ripple
dB
ΔVout Rejection
(7.5–18)
(14.5–25)
(17.5–28.5)
Input Voltage
Required to
Maintain Line
Regulation
Tj = 25°C, IO = 40 mA
7
14.2
17.3
V
(2) It is recommended that a minimum load capacitor of 0.01 μF be used to limit the high frequency noise bandwidth.
Copyright © 1998–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM140L LM340L
LM140L, LM340L
SNVS758B –APRIL 1998–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
Maximum Average
Power Dissipation
(Metal Can Package)
Maximum Average Power
Dissipation
Figure 3.
Figure 4.
Maximum Average Power
Dissipation (Plastic Package)
Peak Output Current
Figure 5.
Figure 6.
Dropout Voltage
Output Impedance
Figure 7.
Figure 8.
4
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM140L LM340L
LM140L, LM340L
www.ti.com
SNVS758B –APRIL 1998–REVISED MARCH 2013
Typical Performance Characteristics (continued)
Ripple Rejection
Quiescent Current
Figure 9.
Figure 10.
Quiescent Current
Figure 11.
Copyright © 1998–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM140L LM340L
LM140L, LM340L
SNVS758B –APRIL 1998–REVISED MARCH 2013
www.ti.com
TYPICAL APPLICATIONS
*Required if the regulator is located far from the power supply filter.
**It is recommended that a minimum load capacitor of 0.01 μF be used to limit the high frequency noise bandwidth.
Figure 12. Fixed Output Regulator
VOUT = 5V + (5V/R1 + IO) R2
5V/R1 = 3 IO load regulation (L,) [(R1 + R2)/R1] (L, of LM140LA-5.0)
Figure 13. Adjustable Output Regulator
6
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM140L LM340L
LM140L, LM340L
www.ti.com
SNVS758B –APRIL 1998–REVISED MARCH 2013
Equivalent Circuit
Copyright © 1998–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM140L LM340L
LM140L, LM340L
SNVS758B –APRIL 1998–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision A (March 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format ............................................................................................................ 7
8
Submit Documentation Feedback
Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM140L LM340L
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
LM140LAH-12
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-55 to 125
-55 to 125
-55 to 125
-55 to 125
-55 to 125
-55 to 125
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
TO
TO
NDT
3
3
3
3
3
3
3
3
500
Green (RoHS POST-PLATE
& no Sb/Br)
Level-1-NA-UNLIM
Level-1-NA-UNLIM
Level-1-NA-UNLIM
Level-1-NA-UNLIM
Level-1-NA-UNLIM
Level-1-NA-UNLIM
Level-1-NA-UNLIM
Level-1-NA-UNLIM
LM140LAH-12
LM140LAH-12/NOPB
LM140LAH-15
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
NDT
NDT
NDT
NDT
NDT
LP
500
500
Green (RoHS POST-PLATE
& no Sb/Br)
LM140LAH-12
LM140LAH-15
LM140LAH-15
LM140LAH-5.0
LM140LAH-5.0
TO
Green (RoHS POST-PLATE
& no Sb/Br)
LM140LAH-15/NOPB
LM140LAH-5.0
TO
500
Green (RoHS POST-PLATE
& no Sb/Br)
TO
500
Green (RoHS POST-PLATE
& no Sb/Br)
LM140LAH-5.0/NOPB
LM340LAZ-5.0/LFT4
LM340LAZ-5.0/NOPB
TO
500
Green (RoHS POST-PLATE
& no Sb/Br)
TO-92
TO-92
2000
1800
Green (RoHS
& no Sb/Br)
SNCU
340LA
Z-5.0
LP
Green (RoHS
& no Sb/Br)
SNCU
0 to 70
340LA
Z-5.0
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
NDT0003A
H03A (Rev D)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明