LM4819MX [TI]
LM4819 350mW Audio Power Amplifier with Shutdown Mode; LM4819 350mW的音频功率放大器关断模式
| 型号： | LM4819MX |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | LM4819 350mW Audio Power Amplifier with Shutdown Mode |
| 文件： | 总27页 (文件大小：1566K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
LM4819
350mW Audio Power Amplifier with Shutdown Mode
Check for Samples: LM4819, LM4819MBD
1
FEATURES
DESCRIPTION
The LM4819 is a mono bridged power amplifier that
2
•
WSON, SOIC, and VSSOP Surface Mount
Packaging
is capable of delivering 350mWRMS output power into
a 16Ω load or 300mWRMS output power into an 8Ω
load with 10% THD+N from a 5V power supply.
•
•
•
Switch On/Off Click Suppression
Unity-Gain Stable
The LM4819 Boomer audio power amplifier is
designed specifically to provide high quality output
power and minimize PCB area with surface mount
Minimum External Components
KEY SPECIFICATIONS
packaging and
a minimal amount of external
components. Since the LM4819 does not require
output coupling capacitors, bootstrap capacitors or
snubber networks, it is optimally suited for low-power
portable applications.
•
•
•
THD+N at 1kHz, 350mW Continuous Average
Output Power into 16Ω: 10% (max)
THD+N at 1kHz, 300mW Continuous Average
Output Power into 8Ω: 10% (max)
The closed loop response of the unity-gain stable
LM4819 can be configured using external gain-setting
resistors. The device is available in WSON, VSSOP,
and SOIC package types to suit various applications.
Shutdown Current: 0.7μA (typ)
APPLICATIONS
•
•
•
General Purpose Audio
Portable Electronic Devices
Information Appliances (IA)
Typical Application
Figure 1. Typical Audio Amplifier Application Circuit
Connection Diagrams
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2001–2013, Texas Instruments Incorporated
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
Top View
Top View
Figure 2. Small Outline (SOIC) Package
See Package Number D0008A
Figure 3. Mini Small Outline (VSSOP) Package
See Package Number DGK0008A
Top View
Figure 4. WSON Package
See Package Number NGL0008B
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
Absolute Maximum Ratings(1)(2)(3)
Supply Voltage
6.0V
−65°C to +150°C
−0.3V to VDD +0.3V
Internally Limited
3.5kV
Storage Temperature
Input Voltage
Power Dissipation (PD)(4)
ESD Susceptibility(5)
ESD Susceptibility(6)
250V
Junction Temperature (TJ)
150°C
Soldering Information
Thermal Resistance
Small Outline Package
Vapor Phase (60 seconds)
215°C
220°C
Infrared (15 seconds)
θJC (VSSOP)
θJA (VSSOP)
θJC (SOIC)
56°C/W
210°C/W
35°C/W
θJA (SOIC)
170°C/W
117°C/W(7)
150°C/W(8)
θJA (WSON)
θJA (WSON)
(1) All voltages are measured with respect to the ground pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given. However, the typical value is a good indication
of device's performance.
(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
(4) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature
TA. The maximum allowable power dissipation is PDMAX = (TJMAX–TA)/θJA. For the LM4819, TJMAX = 150°C and the typical junction-to-
ambient thermal resistance (θJA) when board mounted is 210°C/W for the VSSOP package and 170°C/W for the SOIC package.
(5) Human body model, 100pF discharged through a 1.5 kΩ resistor.
(6) Machine Model, 220pF–240pF capacitor is discharged through all pins.
(7) The given θJA is for an LM4819 package in an NGL0008B with the Exposed-DAP soldered to a printed circuit board copper pad with an
area equivalent to that of the Exposed-DAP itself. The Exposed-DAP of the NGL0008B package should be electrically connected to
GND or an electrically isolated copper area.
(8) The given θJA is for an LM4819 package in an NGL0008B with the Exposed-DAP not soldered to any printed circuit board copper.
Operating Ratings(1)(2)
Temperature Range
−40°C ≤ TA ≤ 85°C
TMIN ≤ TA ≤ TMAX
Supply Voltage
2.0V ≤ VCC ≤ 5.5V
(1) All voltages are measured with respect to the ground pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given. However, the typical value is a good indication
of device's performance.
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
Electrical Characteristics VDD = 5V(1)(2)
The following specifications apply for VDD = 5V, RL = 16Ω unless otherwise stated. Limits apply for TA = 25°C.
LM4819
Units
(Limits)
Parameter
Test Conditions
Typical(3)
Limit(4)(5)
IDD
Quiescent Power Supply Current
Shutdown Current
VIN = 0V, Io = 0A
1.5
3.0
mA (max)
µA (max)
V (min)
V (max)
mV (max)
mW
(6)
ISD
VPIN1 = VDD
1.0
5.0
VSDIH
VSDIL
VOS
Shutdown Voltage Input High
Shutdown Voltage Input Low
Output Offset Voltage
4.0
1.0
VIN = 0V
5
50
THD = 10%, fIN = 1kHz
350
300
1
PO
Output Power
THD = 10%, fIN = 1kHz, RL = 8Ω
PO = 270mWRMS, AVD = 2, fIN = 1kHz
mW
THD+N
Total Harmonic Distortion + Noise
%
(1) All voltages are measured with respect to the ground pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given. However, the typical value is a good indication
of device's performance.
(3) Typical specifications are specified at 25°C and represent the parametric norm.
(4) Tested limits are specified to TI's AOQL (Average Outgoing Quality Level).
(5) Datasheet min/max specification limits are specified by designs, test, or statistical analysis.
(6) The shutdown pin (pin1) should be driven as close as possible to VDD for minimum current in Shutdown Mode.
Electrical Characteristics VDD = 3V(1)(2)
The following specifications apply for VDD = 3V and RL = 16Ω load unless otherwise stated. Limits apply to TA = 25°C.
LM4819
Typical(3)
Units
(Limits)
Parameter
Test Conditions
Limit(4)(5)
3.0
IDD
Quiescent Power Supply Current
Shutdown Current
VIN = 0V, Io = 0A
1.0
0.7
mA (max)
µA (max)
V (min)
V (max)
mV
(6)
ISD
VPIN1 = VDD
5.0
VSDIH
VSDIL
VOS
Shutdown Voltage Input High
Shutdown Voltage Input Low
Output Offset Voltage
2.4
0.6
VIN = 0V
5
110
90
1
50
THD = 10%, fIN = 1kHz
mW
PO
Output Power
THD = 10%, fIN = 1kHz, RL = 8Ω
PO = 80mWRMS, AVD = 2, fIN = 1kHz
mW
THD+N
Total Harmonic Distortion + Noise
%
(1) All voltages are measured with respect to the ground pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given. However, the typical value is a good indication
of device's performance.
(3) Typical specifications are specified at 25°C and represent the parametric norm.
(4) Tested limits are specified to TI's AOQL (Average Outgoing Quality Level).
(5) Datasheet min/max specification limits are specified by designs, test, or statistical analysis.
(6) The shutdown pin (pin1) should be driven as close as possible to VDD for minimum current in Shutdown Mode.
4
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
External Components Description
(See Figure 1)
Components
Functional Description
1.
Ri
Combined with Rf, this inverting input resistor sets the closed-loop gain. Ri also forms a high pass filter with Ci at fc =
1/(2πRiCi).
2.
Ci
This input coupling capacitor blocks DC voltage at the amplifier's terminals. Combined with Ri, it creates a high pass
filter with Ri at fc = 1/(2πRiCi). Refer to the section, Proper Selection of External Components for an explanation of how
to determine the value of Ci.
3.
4.
Rf
Combined with Ri, this is the feedback resistor that sets the closed-loop gain: Av = 2(RF/Ri).
CS
This is the power supply bypass capacitor that filters the voltage applied to the power supply pin. Refer to the
Application Information section for proper placement and selection of Cs.
5.
CB
This is the bypass pin capacitor that filters the voltage at the BYPASS pin. Refer to the section, Proper Selection of
External Components, for information concerning proper placement and selection of CB.
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
THD+N vs Frequency
THD+N vs Frequency
Figure 5.
Figure 6.
THD+N vs Frequency
THD+N vs Frequency
Figure 7.
Figure 8.
THD+N vs Frequency
THD+N vs Frequency
Figure 9.
Figure 10.
6
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
Typical Performance Characteristics (continued)
THD+N vs Output Power
THD+N vs Output Power
Figure 11.
Figure 12.
THD+N vs Output Power
THD+N vs Output Power
Figure 13.
Figure 14.
THD+N vs Output Power
THD+N vs Output Power
Figure 15.
Figure 16.
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Output Power vs Supply Voltage
Output Power vs Supply Voltage
RL = 8Ω
RL = 16Ω
Figure 17.
Figure 18.
Output Power vs Supply Voltage
RL = 32Ω
Output Power vs Load Resistance
Figure 19.
Figure 20.
Power Dissipation vs
Output Power
VDD = 5V
Power Dissipation vs
Output Power
VDD = 3V
Figure 21.
Figure 22.
8
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
Typical Performance Characteristics (continued)
Frequency Response vs
Input Capacitor Size
Power Derating Curves
Figure 23.
Figure 24.
Supply Current vs
Supply Voltage
Figure 25.
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
APPLICATION INFORMATION
BRIDGE CONFIGURATION EXPLANATION
As shown in Figure 1, the LM4819 consists of two operational amplifiers. External resistors, Ri and RF set the
closed-loop gain of the first amplifier (and the amplifier overall), whereas two internal 20kΩ resistors set the
second amplifier's gain at -1. The LM4819 is typically used to drive a speaker connected between the two
amplifier outputs.
Figure 1 shows that the output of Amp1 servers as the input to Amp2, which results in both amplifiers producing
signals identical in magnitude but 180° out of phase. Taking advantage of this phase difference, a load is placed
between V01 and V02 and driven differentially (commonly referred to as "bridge mode"). This results in a
differential gain of
AVD= 2 *(Rf/Ri)
(1)
Bridge mode is different from single-ended amplifiers that drive loads connected between a single amplifier's
output and ground. For a given supply voltage, bridge mode has a distinct advantage over the single-ended
configuration: its differential output doubles the voltage swing across the load. This results in four times the
output power when compared to a single-ended amplifier under the same conditions. This increase in attainable
output assumes that the amplifier is not current limited or the output signal is not clipped. To ensure minimum
output signal clipping when choosing an amplifier's closed-loop gain, refer to the Audio Power Amplifier Design
Example section.
Another advantage of the differential bridge output is no net DC voltage across the load. This results from biasing
V01 and V02 at half-supply. This eliminates the coupling capacitor that single supply, single-ended amplifiers
require. Eliminating an output coupling capacitor in a single-ended configuration forces a single supply amplifier's
half-supply bias voltage across the load. The current flow created by the half-supply bias voltage increases
internal IC power dissipation and may permanently damage loads such as speakers.
POWER DISSIPATION
Power dissipation is a major concern when designing a successful bridged or single-ended amplifier. Equation 2
states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and
driving a specified load.
PDMAX = (VDD)2 /(2π2RL ) (W) Single-ended
(2)
However, a direct consequence of the increased power delivered to the load by a bridged amplifier is an increase
in the internal power dissipation point for a bridge amplifier operating at the same given conditions. Equation 3
states the maximum power dissipation point for a bridged amplifier operating at a given supply voltage and
driving a specified load.
PDMAX = 4(VDD)2/(2π2 RL ) (W) Bridge Mode
(3)
The LM4819 has two operational amplifiers in one package and the maximum internal power dissipation is four
times that of a single-ended amplifier. However, even with this substantial increase in power dissipation, the
Lm4819 does not require heatsinking. From Equation 3, assuming a 5V power supply and an 8Ω load, the
maximum power dissipation point is 633mW. The maximum power dissipation point obtained from Equation 3
must not exceed the power dissipation predicted by Equation 4:
PDMAX = (TJMAX - TA)/θJA (W)
(4)
For the micro DGK0008A package, θJA = 210°C/W, for the D0008A package, θJA = 170°C/W , and TJMAX = 150°C
for the LM4819. For a given ambient temperature, TA, Equation 4 can be used to find the maximum internal
power dissipation supported by the IC packaging. If the result of Equation 3 is greater than the result of
Equation 4, then decrease the supply voltage, increase the load impedance, or reduce the ambient temperature.
For a typical application using the D0008A packaged LM4819 with a 5V power supply and an 8Ω load, the
maximum ambient temperature that does not violate the maximum junction temperature is approximately 42°C. If
a DGK0008A packaged part is used instead with the same supply voltage and load, the maximum ambient
temperature is 17°C. In both cases, it is assumed that a device is a surface mount part operating around the
maximum power dissipation point. The assumption that the device is operating around the maximum power
dissipation point is incorrect for an 8Ω load. The maximum power dissipation point occurs when the output power
is equal to the maximum power dissipation or 50% efficiency. The LM4819 is not capable of the output power
level (633mW) required to operate at the maximum power dissipation point for an 8Ω load. To find the maximum
power dissipation, the graph Figure 22 must be used. From the graph, the maximum power dissipation for an 8Ω
10
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
load and a 5V supply is approximately 575mW. Substituting this value back into Equation 4 for PDMAX and using
θJA = 210°C/W for the DGK0008A package, the maximum ambient temperature is calculated to be 29°C. Using
θJA = 170°C/W for the D0008A package, the maximum ambient temperature is 52°C. Refer to the Typical
Performance Characteristics curves for power dissipation information for lower output powers and maximum
power dissipation for each package at a given ambient temperature.
POWER SUPPLY BYPASSING
As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply
rejection. The capacitors connected to the bypass and power supply pins should be placed as close to the
LM4819 as possible. The capacitor connected between the bypass pin and ground improves the internal bias
voltage's stability, producing improved PSRR. The improvements to PSRR increase as the bypass pin capacitor
value increases. Typical applications employ a 5V regulator with 10µF and 0.1µF filter capacitors that aid in
supply stability. Their presence, however, does not eliminate the need for bypassing the supply nodes of the
LM4819. The selection of bypass capacitor values, especially CB , depends on desired PSRR requirements, click
and pop performance as explained in the section, Proper Selection of External Components, as well as system
cost and size constraints.
SHUTDOWN FUNCTION
The voltage applied to the LM4819's SHUTDOWN pin controls the shutdown function. Activate micro-power
shutdown by applying VDD to the SHUTDOWN pin. When active, the LM4819's micro-power shutdown feature
turns off the amplifier's bias circuitry, reducing the supply current. The logic threshold is typically 1/2VDD. The low
0.7µA typical shutdown current is achieved by applying a voltage that is as near as VDD as possible to the
SHUTDOWN pin. A voltage that is less than VDD may increase the shutdown current. Avoid intermittent or
unexpected micro-power shutdown by ensuring that the SHUTDOWN pin is not left floating but connected to
either VDD or GND.
There are a few ways to activate micro-power shutdown. These included using a single-pole, single-throw switch,
a microcontroller, or a microprocessor. When using a switch, connect an external 10kΩ to 100kΩ pull-up resistor
between the SHUTDOWN pin and VDD. Connect the switch between the SHUTDOWN pin and ground. Select
normal amplifier operation by closing the switch. Opening the switch connects the shutdown pin to VDD through
the pull-up resistor, activating micro-power shutdown. The switch and resistor ensure that the SHUTDOWN pin
will not float. This prevents unwanted state changes. In a system with a microprocessor or a microcontroller, use
a digital output to apply the control voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin with active
circuitry eliminates the pull-up resistor
PROPER SELECTION OF EXTERNAL COMPONENTS
Optimizing the LM4819's performance requires properly selecting external components. Though the LM4819
operates well when using external components with wide tolerances, best performance is achieved by optimizing
component values.
The LM4819 is unity gain stable, giving the designer maximum design flexibility. The gain should be set to no
more than a given application requires. This allows the amplifier to achieve minimum THD+N and maximum
signal-to-noise ratio. These parameters are compromised as the closed-loop gain increases. However, low gain
demands input signals with greater voltage swings to achieve maximum output power. Fortunately, many signal
sources such as audio CODECs have outputs of 1VRMS (2.83VP-P). Please refer to the Audio Power Amplifier
Design section for more information on selecting the proper gain.
Another important consideration is the amplifier's close-loop bandwidth. To a large extent, the bandwidth is
dictated by the choice of external components shown in Figure 1. The input coupling capacitor, Ci, forms a first
order high pass filter that limits low frequency response. This value should be chosen based on needed
frequency response for a few distinct reasons discussed below
Input Capacitor Value Selection
Amplifying the lowest audio frequencies requires a high value input coupling capacitor (Ci in Figure 1). A high
value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases the
speakers used in portable systems, whether internal or external, have little ability to reproduce signals below
150Hz. Applications using speakers with limited frequency response reap little improvement by using a large
input capacitor.
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
Besides affecting system cost and size, Ci has an effect on the LM4819's click and pop performance. When the
supply voltage is first applied, a transient (pop) is created as the charge on the input capacitor changes from zero
to a quiescent state. The magnitude of the pop is directly proportional to the input capacitor's value. Higher value
capacitors need more time to reach a quiescent DC voltage (usually 1/2 VDD) when charged with a fixed current.
The amplifier's output charges the input capacitor through the feedback resistor, RF. Thus, selecting an input
capacitor value that is no higher than necessary to meet the desired -3dB frequency can minimize pops.
As shown in Figure 1, the input resistor (Ri) and the input capacitor, Ci produce a -3dB high pass filter cutoff
frequency that is found using Equation 5.
f-3dB = 1/(2 πRiCi) (Hz)
(5)
As an example when using a speaker with a low frequency limit of 150Hz, Ci, using Equation 5 is 0.063µF. The
0.39µF Ci shown in Figure 1 allows the LM4819 to drive a high efficiency, full range speaker whose response
extends down to 20Hz.
Besides optimizing the input capacitor value, the bypass capacitor value, CB requires careful consideration. The
bypass capacitor's value is the most critical to minimizing turn-on pops because it determines how fast the
LM4819 turns on. The slower the LM4819's outputs ramp to their quiescent DC voltage (nominally 1/2VDD), the
smaller the turn-on pop. While the device will function properly (no oscillations or motorboating), with CB less
than 1.0µF, the device will be much more susceptible to turn-on clicks and pops. Thus, a value of CB equal to or
greater than 1.0µF is recommended in all but the most cost sensitive designs.
Bypass Capacitor Value Selection
Besides minimizing the input capacitor size, careful consideration should be paid to the value of CB, the capacitor
connected to the BYPASS pin. Since CB determines how fast the LM4819 settles to quiescent operation, its
value is critical when minimizing turn-on pops. The slower the LM4819's outputs ramp to their quiescent DC
voltage (nominally 1/2VDD), the smaller the turn-on pop. Choosing CB equal to 1.0µF along with a small value of
Ci (in the range of 0.1µF to 0.39µF) produces a click-less and pop-less shutdown function. As discussed above,
choosing Ci no larger than necessary for the desired bandwidth helps minimize clicks and pops.
Optimizing Click and Pop Reduction Performance
The LM4819 contains circuitry that minimizes turn-on and shutdown transients or "clicks and pops". For this
discussion, turn on refers to either applying the power or supply voltage or when the shutdown mode is
deactivated. While the power supply is ramping to it's final value, the LM4819's internal amplifiers are configured
as unity gain buffers. An internal current source charges the voltage of the bypass capacitor, CB, connected to
the BYPASS pin in a controlled, linear manner. Ideally, the input and outputs track the voltage charging on the
bypass capacitor. The gain of the internal amplifiers remains unity until the bypass capacitor is fully charged to
1/2VDD. As soon as the voltage on the bypass capacitor is stable, the device becomes fully operational. Although
the BYPASS pin current cannot be modified, changing the size of the bypass capacitor, CB, alters the device's
turn-on time and magnitude of "clicks and pops". Increasing the value of CB reduces the magnitude of turn-on
pops. However, this presents a tradeoff: as the size of CB increases, the turn-on time (Ton) increases. There is a
linear relationship between the size of CB and the turn on time. Below are some typical turn-on times for various
values of CB:
CB
TON
20ms
200ms
440ms
940ms
2S
0.01µF
0.1µF
0.22µF
0.47µF
1.0µF
12
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
In order to eliminate "clicks and pops", all capacitors must be discharged before turn-on. Rapidly switching VDD
may not allow the capacitors to fully discharge, which may cause "clicks and pops".
AUDIO POWER AMPLIFIER DESIGN EXAMPLE
The following are the desired operational parameters:
Given:
Power Output
Load Impedance
Input Level
100mW
16Ω
1Vrms (max)
20kΩ
Input Impedance
Bandwidth
100Hz–20kHz ± 0.25dB
The design begins by specifying the minimum supply voltage necessary to obtain the specified output power. To
find this minimum supply voltage, use the Output Power vs. Supply Voltage graph in the Typical Performance
Characteristics section. From the graph for a 16Ω load, (graphs are for 8Ω, 16Ω, and 32Ω loads) the supply
voltage for 100mW of output power with 1% THD+N is approximately 3.15 volts.
Additional supply voltage creates the benefit of increased headroom that allows the LM4819 to reproduce peaks
in excess of 100mW without output signal clipping or audible distortion. The choice of supply voltage must also
not create a situation that violates maximum dissipation as explained above in the Power Dissipation section. For
example, if a 3.3V supply is chosen for extra headroom then according to Equation 3 the maximum power
dissipation point with a 16Ω load is 138mW. Using Equation 4 the maximum ambient temperature is 121°C for
the DGK0008A package and 126°C for the D0008A package.
After satisfying the LM4819's power dissipation requirements, the minimum differential gain is found using
Equation 6.
(6)
Thus a minimum gain of 1.27 V/V allows the LM4819 to reach full output swing and maintain low noise and
THD+N performance. For this example, let AVD = 1.27. The amplifier's overall gain is set using the input (Ri) and
feedback (RF) resistors. With the desired input impedance set to 20kΩ, the feedback resistor is found using
Equation 7.
RF/Ri = AVD/2 (V/V)
(7)
The value of RF is 13kΩ.
The last step in this design example is setting the amplifier's -3dB frequency bandwidth. To achieve the desired
±0.25dB pass band magnitude variation limit, the low frequency response must extend to at least one-fifth the
lower bandwidth limit and the high frequency response must extend to at least five times the upper bandwidth
limit. The gain variation for both response limits is 0.17dB, well with in the ±0.25dB desired limit.
The results are:
fL = 100Hz/5 = 20Hz
fH = 20 kHz*5 = 100kHz
As mentioned in the External Components section, Ri and Ci create a high pass filter that sets the amplifier's
lower band pass frequency limit. Find the coupling capacitor's value using Equation 8.
Ci ≥ 1/(2πRifc) (F)
(8)
Ci ≥ 0.398µF, a standard value of 0.39µF will be used. The product of the desired high frequency cutoff (100kHz
in this example) and the differential gain, AVD, determines the upper pass band response limit. With AVD = 1.27
and fH = 100kHz, the closed-loop gain bandwidth product (GBWP) is 127kHz. This is less than the LM4819's
900kHz GBWP. With this margin the amplifier can be used in designs that require more differential gain while
avoiding performance restricting bandwidth limitations.
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
Figure 26. Higher Gain Audio Amplifier
The LM4819 is unity-gain stable and requires no external components besides gain-setting resistors, an input
coupling capacitor, and proper supply bypassing in the typical application. However, if a closed-loop differential
gain of greater than 10 is required, a feedback capacitor (C4) may be needed as shown in Figure 26 to
bandwidth limit the amplifier. This feedback capacitor creates a low pass filter that eliminates possible high
frequency oscillations. Care should be taken when calculating the -3dB frequency in that an incorrect
combination of R3 and C4 will cause rolloff before 20kHz. A typical combination of feedback resistor and
capacitor that will not produce audio band high frequency rolloff is R3 = 20kΩ and C4 = 25pF. These components
result in a -3dB point of approximately 320 kHz. It is not recommended that the feedback resistor and capacitor
be used to implement a band limiting filter below 100kHz.
Figure 27. Differential Amplifier Configuration for LM4819
14
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
Figure 28. Reference Design Board and PCB Layout Guidelines
LM4819 SOIC DEMO BOARD ARTWORK
Figure 29. Silk Screen
Figure 30. Top Layer
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
Figure 31. Bottom Layer
LM4819 VSSOP DEMO BOARD ARTWORK
Figure 32. Silk Screen
Figure 33. Top Layer
16
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
Figure 34. Bottom Layer
LM4819 WSON DEMO BOARD ARTWORK
Composite View
Top Layer
Silk Screen
Bottom Layer
Table 1. Mono LM4819 Reference Design Boards
Bill of Material for all Demo Boards
Item
1
Part Number
551011208-001
482911183-001
151911207-001
Part Description
LM4819 Mono Reference Design Board
LM4819 Audio AMP
Qty
1
Ref Designator
10
20
1
U1
C1
Tant Cap 1uF 16V 10
1
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
www.ti.com
Table 1. Mono LM4819 Reference Design Boards
Bill of Material for all Demo Boards (continued)
Item
21
Part Number
Part Description
Cer Cap 0.39uF 50V Z5U 20% 1210
Tant Cap 1uF 16V 10
Qty
1
Ref Designator
151911207-002
152911207-001
472911207-001
210007039-002
C2
C3
25
1
30
Res 20K Ohm 1/10W 5
3
R1, R2, R3
J1, J2
35
Jumper Header Vertical Mount 2X1 0.100
2
PCB LAYOUT GUIDELINES
This section provides practical guidelines for mixed signal PCB layout that involves various digital/analog power
and ground traces. Designers should note that these are only "rule-of-thumb" recommendations and the actual
results will depend heavily on the final layout.
General Mixed Signal Layout Recommendation
Power and Ground Circuits
For two layer mixed signal design, it is important to isolate the digital power and ground trace paths from the
analog power and ground trace paths. Star trace routing techniques (bringing individual traces back to a central
point rather than daisy chaining traces together in a serial manner) can have a major impact on low level signal
performance. Star trace routing refers to using individual traces to feed power and ground to each circuit or even
device. This technique will take require a greater amount of design time but will not increase the final price of the
board. The only extra parts required will be some jumpers.
Single-Point Power / Ground Connections
The analog power traces should be connected to the digital traces through a single point (link). A "Pi-filter" can
be helpful in minimizing high frequency noise coupling between the analog and digital sections. It is further
recommended to put digital and analog power traces over the corresponding digital and analog ground traces to
minimize noise coupling.
Placement of Digital and Analog Components
All digital components and high-speed digital signals traces should be located as far away as possible from
analog components and circuit traces.
Avoiding Typical Design / Layout Problems
Avoid ground loops or running digital and analog traces parallel to each other (side-by-side) on the same PCB
layer. When traces must cross over each other do it at 90 degrees. Running digital and analog traces at 90
degrees to each other from the top to the bottom side as much as possible will minimize capacitive noise
coupling and cross talk.
18
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LM4819 LM4819MBD
LM4819, LM4819MBD
www.ti.com
SNAS133D –FEBRUARY 2001–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision C (March 2013) to Revision D
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 18
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM4819 LM4819MBD
PACKAGE OPTION ADDENDUM
www.ti.com
18-Oct-2013
PACKAGING INFORMATION
Orderable Device
LM4819LD/NOPB
LM4819LDX/NOPB
LM4819MM/NOPB
LM4819MMX/NOPB
LM4819MX/NOPB
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
WSON
WSON
VSSOP
VSSOP
SOIC
NGL
8
8
8
8
8
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
Level-3-260C-168 HR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
G19
G19
G19
G19
ACTIVE
ACTIVE
ACTIVE
ACTIVE
NGL
DGK
DGK
D
4500
1000
3500
2500
Green (RoHS
& no Sb/Br)
CU SN
-40 to 85
Green (RoHS
& no Sb/Br)
CU SN
-40 to 85
Green (RoHS
& no Sb/Br)
CU SN
-40 to 85
Green (RoHS
& no Sb/Br)
SN | CU SN
-40 to 85
LM48
19M
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
18-Oct-2013
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
12-Aug-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM4819LD/NOPB
LM4819LDX/NOPB
LM4819MM/NOPB
LM4819MMX/NOPB
LM4819MX/NOPB
WSON
WSON
VSSOP
VSSOP
SOIC
NGL
NGL
DGK
DGK
D
8
8
8
8
8
1000
4500
1000
3500
2500
178.0
330.0
178.0
330.0
330.0
12.4
12.4
12.4
12.4
12.4
2.8
2.8
5.3
5.3
6.5
2.8
2.8
3.4
3.4
5.4
1.0
1.0
1.4
1.4
2.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
12-Aug-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM4819LD/NOPB
LM4819LDX/NOPB
LM4819MM/NOPB
LM4819MMX/NOPB
LM4819MX/NOPB
WSON
WSON
VSSOP
VSSOP
SOIC
NGL
NGL
DGK
DGK
D
8
8
8
8
8
1000
4500
1000
3500
2500
213.0
367.0
210.0
367.0
367.0
191.0
367.0
185.0
367.0
367.0
55.0
35.0
35.0
35.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
NGL0008B
LDA08B (Rev B)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明