LM5007SDX [TI]
High Voltage 80-V Step Down Switching Regulator;型号: | LM5007SDX |
厂家: | TEXAS INSTRUMENTS |
描述: | High Voltage 80-V Step Down Switching Regulator 开关 |
文件: | 总17页 (文件大小:994K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM5007
www.ti.com
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
High Voltage (80V) Step Down Switching Regulator
Check for Samples: LM5007
1
FEATURES
DESCRIPTION
The LM5007 Step Down Switching Regulator features
all of the functions needed to implement low cost,
efficient, Buck bias regulators. This high voltage
regulator contains an 80 V, 0.7A N-Channel Buck
Switch. The device is easy to apply and is provided in
the VSSOP-8 and the thermally enhanced WSON-8
packages. The regulator is based on a hysteretic
control scheme using an on time inversely
proportional to VIN. This feature allows the operating
frequency to remain relatively constant with load and
input voltage variations. The hysteretic control
requires no control loop compensation, while
providing very fast load transient response. An
intelligent current limit is implemented in the LM5007
with forced off time that is inversely proportional to
VOUT. This current limiting scheme reduces load
current foldback. Additional protection features
include: Thermal Shutdown, Vcc undervoltage
lockout, gate drive undervoltage lockout, and Max
Duty Cycle limiter.
2
•
•
•
•
•
•
Integrated 80V, 0.7A N-Channel Buck Switch
Internal HV Vcc Regulator
No Control Loop Compensation Required
Ultra-Fast Transient Response
On Time Varies Inversely with Line Voltage
Operating Frequency Nearly Constant with
Varying Line Voltage
•
•
•
•
•
•
•
•
Adjustable Output Voltage
Highly Efficient Operation
Precision Reference
Low Bias Current
Intelligent Current Limit Protection
Thermal Shutdown
External Shutdown Control
VSSOP-8 and WSON-8 (4mm x 4mm) Packages
APPLICATIONS
•
•
•
Non-Isolated Buck Regulator
Secondary High Voltage Post Regulator
+42V Automotive Systems
Connection Diagram
1
2
3
4
8
SW
VIN
7
VCC
BST
RCL
6
RON
5
RTN
FB
Figure 1. 8-Lead VSSOP or WSON
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2013, Texas Instruments Incorporated
LM5007
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
www.ti.com
Typical Application Circuit and Block Diagram
7V SERIES
REGULATOR
LM5007
V
CC
7
12 -75V
8
V
IN
SD
C5
C1
1 m
C3
0.1 m
0.1 m,
100V
THERMAL
SHUTDOWN
UVLO
ON TIMER
R1
200k
START
COMPLETE
Ron
6
2
BST
SD /
RON
START
V
OVER-VOLTAGE
COMPARATOR
IN
SD
UVLO
300nS MIN OFF
TIMER
SHUTDOWN
C4
0.01m
+
DRIVER
-
2.875V
2.5V
COMPLETE
100 m
LEVEL
SHIFT
L1
10V
SW
1
SET
CLR
+
-
S
Q
Q
5
FB
R
REGULATION
COMPARATOR
R3
R6
1
3.01k
FB
RCL
COMPLETE
3
BUCK
SWITCH
CURRENT
SENSE
+
-
RCL
START
R2
100k
CURRENT LIMIT
OFF TIMER
D1
0.725A
4
C2
15 m
RTN
R4
1k
Pin Functions
Table 1. Pin Descriptions
Pin
1
Name
SW
Description
Application Information
Power switching node. Connect to the LC output filter.
Switching Node
2
BST
Boost Boot–strap capacitor input
An external capacitor is required between the BST and the SW
pins. A 0.01uF ceramic capacitor is recommended. An internal
diode between Vcc and BST completes the Buck gate drive bias
network.
3
RCL
Current Limit OFF time programming pin
A resistor between this pin and RTN determines the variation of
off time, along with the FB pin voltage, per cycle while in current
limit. The off time is preset to 17uS if FB =0V and decreases as
the FB pin voltage increases.
Toff = 10-5 / (0.59 + (FB / 7.22 x 10− 6 x RCL))
4
5
RTN
FB
Circuit Ground
Feedback Signal from Regulated Output
This pin is connected to the inverting input of the internal
regulation comparator. The regulation threshold is 2.5V.
6
7
RON
Vcc
On time set pin
A resistor between this pin and Vin sets the switch on time as a
function of Vin. The minimum recommended on time is 300ns at
the maximum input voltage.
Ton = 1.42 x 10-10 RON / Vin
Output from the internal high voltage bias
regulator. VCC is nominally regulated to 7 V.
If an auxiliary voltage is available to raise the voltage on this pin,
above the regulation set point (7V), the internal series pass
regulator will shutdown, reducing the IC power dissipation. Do
not exceed 14V. This output provides gate drive power for the
internal Buck switch. An internal diode is provided between this
pin and the BST pin. A local 0.1uF decoupling capacitor is
recommended. Series pass regulator is current limited to 10mA.
8
-
Vin
EP
Input supply voltage
Recommended operating range: 9V to 75V.
Exposed PAD, underside of the WSON
package option
Internally bonded to the die substrate. Connect to GND potential
for low thermal impedance.
2
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM5007
LM5007
www.ti.com
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
(1)
Absolute Maximum Ratings
VIN to GND
80V
BST to GND
94V
SW to GND (Steady State)
ESD Rating, Human Body Model(2)
Machine Model
-1V
2kV
200V
BST to VCC
80V
BST to SW
14V
VCC to GND
14V
All Other Inputs to GND
Lead Temperature (Soldering 4 sec)
Storage Temperature Range
-0.3 to 7V
260°C
-55°C to +150°C
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For specifications and test conditions, see the Electrical Characteristics.
(2) The human body model is a 100pF capacitor discharge through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor
discharged directly into each pin. The machine model ESD compliance level for Pin 5 is 150V. The human body ESD compliance level
for Pin 7 and 8 is 1000V.
(1)
Operating Ratings
VIN
9V to 75V
Junction Temperature
−40°C to + 125°C
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For specifications and test conditions, see the Electrical Characteristics.
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM5007
LM5007
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
www.ti.com
Electrical Characteristics
Specifications with standard typeface are for TJ = 25°C, and those with boldface type apply over full Operating Junction
(1)
Temperature range. VIN = 48V, unless otherwise stated
.
Symbol
Parameter
Conditions
Min
6.6
Typ
Max
7.4
Unit
Startup Regulator
VCC
Reg
VCC Regulator Output
7
V
VCC Current Limit(2)
11
mA
VCC Supply
VCC undervoltage Lockout Voltage
(VCC increasing)
6.3
V
VCC Undervoltage Hysteresis
VCC UVLO Delay (filter)
206
3
mV
µs
Operating Current (ICC)
Shutdown/Standby Current
Non-Switching, FB = 3V
RON = 0V
500
100
675
200
µA
µA
Switch Characteristics
Buck Switch Rds(on)
ITEST = 200mA,
0.74
1.34
5.5
Ω
VBST −VSW = 6.3V(3)
Gate Drive UVLO (VBST – VSW)
Gate Drive UVLO Hysteresis
Rising
3.4
4.5
V
mV
V
400
Breakdown Voltage,
VIN to Ground
TJ = 25°C
80
76
80
76
TJ = -40°C to +125°C
TJ = 25°C
V
Breakdown Voltage,
BST to VCC
V
TJ = -40°C to +125°C
V
Current Limit
Current Limit Threshold
535
725
225
17
900
mA
ns
Current Limit Response Time
OFF time generator (test 1)
OFF time generator (test 2)
Iswitch Overdrive = 0.1A Time to Switch Off
FB=0V, RCL = 100K
µs
µs
FB=2.3V, RCL = 100K
2.65
On Time Generator
TON -1
Vin = 10V, Ron = 200K
Vin = 75V, Ron = 200K
Rising
2.15
290
2.77
390
0.7
40
3.5
490
1.1
µs
ns
V
TON -2
Remote Shutdown Threshold
Remote Shutdown Hysteresis
0.45
mV
Minimum Off Time
Minimum Off Timer
Regulation and OV Comparators
FB Reference Threshold
FB Over-Voltage Threshold
FB Bias Current
FB = 0V
300
ns
Internal reference, Trip point for switch ON
Trip point for switch OFF
2.445
2.5
2.875
100
2.550
V
V
nA
Thermal Shutdown
Tsd
Thermal Shutdown Temp.
165
25
°C
°C
Thermal Shutdown Hysteresis
Thermal Resistance
θJA Junction to Ambient
VSSOP-8 Package
WSON-8 Package
200
40
°C/W
°C/W
(1) All electrical characteristics having room temperature limits are tested during production with TA = TJ = 25°C. All hot and cold limits are
specified by correlating the electrical characteristics to process and temperature variations and applying statistical process control.
(2) The VCC output is intended as a self bias for the internal gate drive power and control circuits. Device thermal limitations limit external
loading.
(3) For devices in the WSON-8 package, the Rds(on) limits are specified by design characterization data only.
4
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM5007
LM5007
www.ti.com
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
DETAILED OPERATING DESCRIPTION
The LM5007 Step Down Switching Regulator features all of the functions needed to implement low cost, efficient,
Buck bias regulators. This high voltage regulator contains an 80V, 0.7A N-Channel Buck Switch. The device is
easy to apply and is provided in the VSSOP-8 and the thermally enhanced WSON-8 packages. The regulator is
based on a hysteretic control scheme using an on time inversely proportional to Vin. This feature allows the
operating frequency to remain relatively constant with load and input voltage variations. The hysteretic control
requires no control loop compensation, while providing very fast load transient response. An intelligent current
limit scheme is implemented in the LM5007 with forced off time, after current limit detection, which is inversely
proportional to Vout. This current limiting scheme reduces load current foldback. Additional protection features
include: Thermal Shutdown, Vcc undervoltage lockout, Gate drive undervoltage lockout and Max Duty Cycle
limiter. The LM5007 can be applied in numerous applications to efficiently regulate step down higher voltage
inputs. This regulator is well suited for 48 Volt Telcom and the new 42V Automotive power bus ranges.
Hysteretic Control Circuit Overview
The LM5007 is a Buck DC-DC regulator that uses an on time control scheme. The on time is programmed by an
external resistor and varies inversely with line input voltage (Vin). The core regulation elements of the LM5007
are the feedback comparator and the on time one-shot. The regulator output voltage is sensed at the feedback
pin (FB) and is compared to an internal reference voltage (2.5V). If the FB signal is below the reference voltage,
the buck switch is turned on for a fixed time pulse determined by the line voltage and a programming resistor
(RON). Following the on period the switch will remain off for at least the minimum off timer period of 300ns. If the
FB pin voltage is still below the reference after the 300ns off time, the switch will turn on again for another on
time period. This switching behavior will continue until the FB pin voltage reaches the reference voltage level.
The LM5007 operates in discontinuous conduction mode at light load currents or continuous conduction mode at
heavier load currents. In discontinuous conduction mode, current through the output inductor starts at zero and
ramps up to a peak value during the buck switch on time and then back to zero during the off time. The inductor
current remains at zero until the next on time period starts when FB falls below the internal reference. In
discontinuous mode the operating frequency can be relatively low and will vary with load. Therefore at light loads
the conversion efficiency is maintained, since the switching losses decrease with the reduction in load current
and switching frequency. The approximate discontinuous mode operating frequency can be calculated as follows:
VOUT2 x L
F =
1 x 10-20 x RLoad x (RON
)
2
(1)
In continuous conduction mode, current flows continuously through the inductor and never ramps down to zero.
In this mode the operating frequency is greater than the discontinuous mode frequency and remains relatively
constant with load and line variations. The approximate continuous mode operating frequency can be calculated
as follows:
VOUT
F =
1.42 x 10-10 x RON
(2)
The output voltage (Vout) can be programmed by two external resistors as shown in Figure 2. The regulation
point can be calculated as follows:
VOUT = 2.5 x (R1 + R2) / R2
(3)
The feedback comparator in hysteretic regulators depend upon the output ripple voltage to switch the output
transistor on and off at regular intervals. In order for the internal comparator to respond quickly to changes in
output voltage, proportional to inductor current, a minimum amount of capacitor Equivalent Series Resistance
(ESR) is required. A ripple voltage of 25mV to 50mV is recommended at the feedback pin (FB) for stable
operation. In cases where the intrinsic capacitor ESR is too small, additional series resistance may be added.
For applications where lower output voltage ripple is required the load can be connected directly to the low ESR
output capacitor, as shown in Figure 2. The series resistor (R) will degrade the load regulation. Another
technique for enhancing the ripple voltage at the FB pin is to place a capacitor in parallel with the feedback
divider resistor R1. The addition of the capacitor reduces the attenuation of the ripple voltage from the feedback
divider
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM5007
LM5007
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
www.ti.com
High Voltage Bias Regulator
The LM5007 contains an internal high voltage bias regulator. The input pin (Vin) can be connected directly to line
voltages from 9 V to 75 V. To avoid supply voltage transients due to long lead inductances on the input pin (Vin
Pin 8), it is always recommended to connect low ESR ceramic chip capacitor (≊ 0.1µF) between "Vin" pin and
"RTN" pin (pin 4), located close to LM5007. The regulator is internally current limited to 10mA. Upon power up,
the regulator is enabled and sources current into an external capacitor connected to the Vcc pin. When the
voltage on the Vcc pin reaches the regulation point of 7V, the controller output is enabled.
An external auxiliary supply voltage can be applied to the Vcc pin. If the auxiliary voltage is greater than 7 V, the
internal regulator will essentially shutoff, thus reducing internal power dissipation.
VIN
L
SW
R1
R2
R
FB
+
-
V
OUT
+
C
OUT
REF
2.5V
LM5007
Figure 2. Low Ripple Output Configuration
7V SERIES REGULATOR
VCC
+
0.1mF
SELF-BIAS
DIODE
BST
VIN
+
0.01mF
SW
LM5007
10V
30k
10k
+
Figure 3. Self Biased Configuration
6
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM5007
LM5007
www.ti.com
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
Over-Voltage Comparator
The over-voltage comparator is provided to protect the output from overvoltage conditions due to sudden input
line voltage changes or output loading changes. The over-voltage comparator monitors the FB pin versus an
internal 2.875V reference (OV_REF). If the voltage at FB rises above OV_REF the comparator immediately
terminates the buck switch on time pulse.
ON Time generator and Shutdown
The on time of the LM5007 is set inversely proportional to the input voltage by an external resistor connected
between Ron and Vin. The Ron terminal is a low impedance input biased at approximately 1.5V. Thus the
current through the resistor and into the Ron terminal is approximately proportional to Vin and used internally to
control the on timer. This scheme of input voltage feed-forward hysteretic operation achieves nearly constant
operational frequency over varying line and load conditions. The on time equation for the LM5007 is :
Ton = 1.42 x 10-10 x RON / VIN
(4)
The RON pin of the LM5007 also provides a shutdown function which disables the regulator and significantly
decreases quiescent power dissipation. By pulling the RON pin to below 0.7V logic threshold activates the low
power shutdown mode. The VIN quiescent current in the shutdown mode is approximately 100µA internal to the
LM5007 plus the current in the RON resistor.
7V SERIES
REGULATOR
VIN
VIN
ON TIMER
START
RON
VIN
RON
RON
COMPLETE
STOP
RUN
LM5007
Figure 4. Shutdown Implementation
Current Limit
The LM5007 contains an intelligent current limit off timer intended to reduce the foldback characteristic inherent
with fixed off-time over-current protection. If the current in the Buck switch exceeds 725mA the present cycle on
time is immediately terminated (cycle by cycle current limit). Following the termination of the cycle a non-
resetable current limit off timer is initiated. The duration of the off time is a function of the external resistor (RCI)
and the FB pin voltage. When the FB pin voltage equals zero, the current limit off time is internally preset to
17uS. This condition occurs in short circuit operation when a maximum amount of off time is required.
In cases of overload (not complete short circuit) the current limit off time can be reduced as a function of the
output voltage (measured at the FB pin). Reducing the off time with smaller overloads reduces the amount of
foldback and also reduces the initial start-up time. The current limit off time for a given FB pin voltage and RCI
resistor can be calculated by the following equation:
(5)
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM5007
LM5007
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
www.ti.com
Applications utilizing low resistance inductors and/or a low voltage drop rectifier may require special evaluation at
high line, short circuit conditions. In this special case the preset 17µs (FB = 0V) off time may be insufficient to
balance the inductor volt*time product. Additional inductor resistance, output resistance or a larger voltage drop
rectifier may be necessary to balance the inductor cycle volt*time product and limit the short circuit current.
N-Channel Buck Switch and Driver
The LM5007 integrates an N-Channel Buck switch and associated floating high voltage gate driver. This gate
driver circuit works in conjunction with an external bootstrap capacitor and an internal high voltage diode. The
bootstrap capacitor is charged by VCC through the internal high voltage diode. A 0.01uF ceramic capacitor
connected between the BST pin and SW pin is recommended.
During each cycle when the Buck switch turns off, the SW pin is approximately 0V. When the SW pin voltage is
low, the bootstrap capacitor will be charged from Vcc through the internal diode. The minimum off timer, set to
300ns, ensures that there will be a minimum interval every cycle to recharge the bootstrap capacitor.
An external re-circulating diode from the SW pin to ground is necessary to carry the inductor current after the
internal Buck switch turns off. This external diode must be of the Ultra-fast or Schottky type to reduce turn-on
losses and current over-shoot. The reverse voltage rating of the re-circulating diode must be greater than the
maximum line input voltage.
Thermal Protection
Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction
temperature is exceeded. When thermal protection is activated, typically at 165 degrees Celsius, the controller is
forced into a low power reset state, disabling the output driver. This feature is provided to prevent catastrophic
failures from accidental device overheating.
Minimum Load Current
A minimum load current of 1 mA is required to maintain proper operation. If the load current falls below that level,
the bootstrap capacitor may discharge during the long off-time, and the circuit will either shutdown, or cycle on
and off at a low frequency. If the load current is expected to drop below 1 mA in the application, the feedback
resistors should be chosen low enough in value so they provide the minimum required current at nominal Vout.
Figure 5. Operational Waveforms:
LM5007 Operation:
VOUT = 10V, VIN = 20V, IOUT = 250mA
CH1: Switch Node, CH2: VOUT (AC),
CH4: Inductor Current
Figure 6. Operational Waveforms:
LM5007 Operation:
VOUT = 10V, VIN = 75V, IOUT = 250mA
CH1: Switch Node, CH2: VOUT (AC),
CH4: Inductor Current
8
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM5007
LM5007
www.ti.com
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
100
95
90
85
80
75
70
65
60
20
18
16
14
12
10
8
VIN = 15V
600k
400k
200k
VIN = 30V
VIN = 50V
VIN = 70V
6
4
2
100k
50k
0
0
0.1
0.2
0.3
0.4
0.5
0
0.5
1
1.5
(V)
2
2.5
V
LOAD (A)
FB
Figure 7. LM5007 10V Output Efficiency
Figure 8. Current Limit VFB vs TOFF
RCL = 50k -600k
5
4.5
4
3.5
3
2.5
2
300k
200k
1.5
1
100k
0.5
0
0
10 20 30 40 50 60 70 80
(V)
V
IN
Figure 9. VIN vs TON
RON = 100k, 200k, 300k
Table 2. 10V, 400mA Demo Board Bill of Materials
ITEM
C1
C2
C3
C4
C5
D1
L1
PART NUMBER
DESCRIPTION
CAPACITOR, CER, TDK
CAPACITOR, CER, TDK
CAPACITOR, CER, KEMET
CAPACITOR, CER, KEMET
CAPACITOR, CER, TDK
DIODE, 100V, ON SEMI
BUCK INDUCTOR, TDK
RESISTOR
VALUE
1µ, 100V
15µ, 25V
0.1µ, 50V
0.01µ, 50V
0.1µ, 100V
C4532X7R2A105M
C4532X7R1E156M
C1206C104K5RAC
C1206C103K5RAC
C3216X7R2A104KT
MURA110T3
SLF7045T-101MR60-1
CRCW12062003F
CRCW12061003F
CRCW12063011F
CRCW12061001F
CRCW12061R00F
LM5007
100µH
200K
100K
3.01K
1K
R1
R2
R3
R4
R5
U1
RESISTOR
RESISTOR
RESISTOR
RESISTOR
1
REGULATOR, TI
Copyright © 2003–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM5007
LM5007
SNVS252F –SEPTEMBER 2003–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision E (March 2013) to Revision F
Page
•
Changed layout of National Data Sheet to TI format ............................................................................................................ 9
10
Submit Documentation Feedback
Copyright © 2003–2013, Texas Instruments Incorporated
Product Folder Links: LM5007
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
LM5007MM
ACTIVE
VSSOP
VSSOP
DGK
8
8
1000
TBD
Call TI
CU SN
Call TI
-40 to 125
-40 to 125
S81B
LM5007MM/NOPB
ACTIVE
DGK
1000
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
S81B
LM5007MMX
ACTIVE
ACTIVE
VSSOP
VSSOP
DGK
DGK
8
8
3500
3500
TBD
Call TI
CU SN
Call TI
-40 to 125
-40 to 125
S81B
S81B
LM5007MMX/NOPB
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LM5007SD
ACTIVE
ACTIVE
WSON
WSON
NGT
NGT
8
8
1000
1000
TBD
Call TI
SN
Call TI
-40 to 125
-40 to 125
L00031B
L00031B
LM5007SD/NOPB
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
LM5007SDX/NOPB
ACTIVE
WSON
NGT
8
4500
Green (RoHS
& no Sb/Br)
SN
Level-1-260C-UNLIM
-40 to 125
L00031B
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM5007MM
LM5007MM/NOPB
LM5007MMX
VSSOP
VSSOP
VSSOP
VSSOP
WSON
WSON
WSON
DGK
DGK
DGK
DGK
NGT
NGT
NGT
8
8
8
8
8
8
8
1000
1000
3500
3500
1000
1000
4500
178.0
178.0
330.0
330.0
178.0
178.0
330.0
12.4
12.4
12.4
12.4
12.4
12.4
12.4
5.3
5.3
5.3
5.3
4.3
4.3
4.3
3.4
3.4
3.4
3.4
4.3
4.3
4.3
1.4
1.4
1.4
1.4
1.3
1.3
1.3
8.0
8.0
8.0
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
LM5007MMX/NOPB
LM5007SD
LM5007SD/NOPB
LM5007SDX/NOPB
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Mar-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM5007MM
LM5007MM/NOPB
LM5007MMX
VSSOP
VSSOP
VSSOP
VSSOP
WSON
WSON
WSON
DGK
DGK
DGK
DGK
NGT
NGT
NGT
8
8
8
8
8
8
8
1000
1000
3500
3500
1000
1000
4500
203.0
203.0
367.0
367.0
203.0
203.0
367.0
190.0
190.0
367.0
367.0
190.0
190.0
367.0
41.0
41.0
35.0
35.0
41.0
41.0
35.0
LM5007MMX/NOPB
LM5007SD
LM5007SD/NOPB
LM5007SDX/NOPB
Pack Materials-Page 2
MECHANICAL DATA
NGT0008A
SDC08A (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明