LM5072MHX-80/NOPB [TI]
Integrated 100V Power Over Ethernet PD Interface;
| 型号： | LM5072MHX-80/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | Integrated 100V Power Over Ethernet PD Interface 开关 光电二极管 |
| 文件： | 总34页 (文件大小：1335K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
LM5072 Integrated 100V Power Over Ethernet PD Interface and PWM Controller with Aux
Support
Check for Samples: LM5072
1
FEATURES
DESCRIPTION
The LM5072 Powered Device (PD) interface and
Pulse-Width-Modulation (PWM) controller provides a
complete power solution, fully compliant to IEEE
802.3af, for the PD connecting into Power over
Ethernet (PoE) networks. This controller integrates all
functions necessary to implement both a PD powered
interface and DC-DC converter with a minimum
number of external components. The LM5072
provides the flexibility for the PD to also accept power
from auxiliary sources such as AC adapters in a
variety of configurations. The low RDS(ON) PD
interface hot swap MOSFET and programmable DC
current limit extend the range of LM5072 applications
up to twice the power level of 802.3af compliant PD
devices. The 100V maximum voltage rating simplifies
selection of the transient voltage suppressor that
protects the PD from network transients. The LM5072
includes an easy-to-use PWM controller that
facilitates the various single-ended power supply
topologies including the flyback, forward and buck.
The PWM control scheme is based on peak current
mode control, which provides inherent advantages
including line feed-forward, cycle-by-cycle current
limit, and simplified feedback loop compensation.
Two versions of the LM5072 provide either an 80%
maximum duty cycle (-80 suffix), or a 50% maximum
duty cycle (-50 suffix).
2
•
PD Interface
–
–
–
Fully Compliant IEEE 802.3af PD Interface
Versatile Auxiliary Power Options
9V Minimum Auxiliary Power Operating
Range
–
–
100V Maximum Input Voltage Rating
Programmable DC Current Limit Up To
800mA
–
–
–
–
–
–
–
100V, 0.7Ω Hot Swap MOSFET
Integrated PD Signature Resistor
Integrated PoE Input UVLO
Programmable Inrush Current Limit
PD Classification Capability
Power Good Indicator
Thermal Shutdown Protection
•
PWM Controller
–
–
–
–
Current Mode PWM Controller
100V Start-Up Regulator
Error Amplifier with 2% Voltage Reference
Supports Isolated and Non-Isolated
Applications
–
–
–
–
Programmable Oscillator Frequency
Programmable Soft-Start
PACKAGES
•
TSSOP-16 EP (Exposed Pad)
800 mA Peak Gate Driver
80% Maximum Duty Cycle with Built-in
Slope Compensation (-80 Device)
–
50% Maximum Duty Cycle, No Slope
Compensation (-50 Device)
APPLICATIONS
•
•
•
IEEE 802.3af Compliant PoE Powered Devices
Non-Compliant, Application Specific Devices
Higher Power Ethernet Powered Devices
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
Simplified Application Diagram
+PoE
www.ti.com
+V
OUT
LM5072
VCC
SS
VIN
RAUX
+ FAUX
- FAUX
RT
ICL_FAUX
COMP
FB
RCLASS
nPGOOD
OUT
CS
DCCL
VEE
ARTN
RTN
-PoE
Connection Diagram
LM5072
1
2
3
4
5
6
7
8
16
15
14
13
12
RT
SS
VIN
ARTN
COMP
FB
RCLASS
ICL_FAUX
DCCL
RAUX
CS
11
10
nPGOOD
VCC
VEE
9
RTN
OUT
Figure 1. 16 Lead TSSOP-EP
2
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
PIN DESCRIPTIONS
Pin Number
Name
RT
Description
1
2
3
4
5
6
7
8
PWM controller oscillator frequency programming pin.
Soft-start programming pin.
SS
VIN
Positive supply pin for the PD interface and the internal PWM controller start-up regulator.
PD classification programming pin.
RCLASS
ICL_FAUX
DCCL
VEE
Inrush current limit programming pin; also the front auxiliary power enable pin.
PD interface DC current limit programming pin.
Negative supply pin for PD interface; connected to PoE and/or front auxiliary power return path.
RTN
PWM controller power return; connected to the drain of the internal PD interface hot swap
MOSFET; should be externally connected to the reference ground of the PWM controller.
9
OUT
VCC
PWM controller gate driver output pin.
10
11
PWM controller start-up regulator output pin.
nPGOOD
PD interface Power Good indicator and delay timer pin; active low state indicates PoE interface is in
normal operation.
12
13
CS
PWM controller current sense input pin.
RAUX
Rear auxiliary power enable pin; can be programmed for auxiliary power dominance over PoE
power.
14
15
16
FB
COMP
ARTN
EP
PWM controller voltage feedback pin and inverting input of the internal error amplifier; connect to
ARTN to disable the error amplifier in isolated dc-dc converter applications.
Output of the internal error amplifier and control input to the PWM comparator. In isolated
applications, COMP is controlled by the secondary side error amplifier via an opto-coupler.
PWM controller reference ground pin; should be shorted externally to the RTN pin as a single point
ground connection to improve noise immunity.
Exposed metal pad on the underside of the device. It is recommended to connect this pad to a PC
Board plane connected to the VEE pin to improve heat dissipation.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
Absolute Maximum Ratings(1)(2)
VIN , RTN to VEE(3)
RAUX to ARTN
-0.3V to 100V
-0.3V to 100V
-0.3V to 100V
-0.3V to 7V
-0.3V to 16V
-0.3V to 0.3V
-0.3V to 16V
-0.3V to 7V
-0.3V to 5.5V
2000V
ICL_FAUX to VEE
DCCL, RCLASS to VEE
nPGOOD to ARTN
ARTN to RTN
VCC, OUT to ARTN
CS, FB, RT to ARTN
COMP, SS to ARTN
ESD Rating
Human Body Model(4)
Wave (4 seconds)
Lead Soldering
Temp.(5)
260°C
Infrared (10 seconds)
Vapor Phase (75 seconds)
240°C
219°C
Storage Temperature
Junction Temperature
-55°C to 150°C
150°C
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For ensured specifications and test conditions, see the Electrical Characteristics
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) During rear auxiliary operation, the RTN pin can be approximately -0.4V with respect to VEE. This is caused by normal internal bias
currents, and will not harm the device. Application of external voltage or current must not cause the absolute maximum rating to be
exceeded.
(4) The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin.
(5) For detailed information on soldering the plastic TSSOP package, refer to the Packaging Databook available from Texas Instruments.
Operating Ratings
VIN voltage
9V to 70V
External voltage applied to VCC
Operating Junction Temperature
8V to 15V
-40°C to 125°C
Electrical Characteristics(1)
Specifications in standard type face are for TJ = +25°C and those in boldface type apply over the full operating junction
temperature range. Unless otherwise specified: VIN = 48V, FOSC = 250kHz.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Detection and Classification
VIN Signature Startup Voltage
Signature Resistance
1.5
26
V
kΩ
V
23.25
11.0
24.5
12.0
Signature Resistor Disengage/
Classification Engage
VIN Rising
12.6
Hysteresis
1.9
23.5
1.25
0.7
V
V
Classification Current Turn Off
Classification Voltage
VIN Rising
VIN = 17V
22
25
1.287
1.1
1.213
V
Supply Current During Classification
mA
Line Under Voltage Lock-Out
UVLO Release
UVLO Lock out
UVLO Hysteresis
UVLO Filter
VIN Rising
VIN Falling
36
29.5
6
38.5
31.0
40
V
V
32.5
V
300
µs
(1) Minimum and Maximum limits are ensured through test, design, or statistical correlation using Statistical Quality Control (SQC) methods.
Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purpose only. Limits are used to
calculate Texas Instruments' Average Outgoing Quality Level (AOQL).
4
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
Electrical Characteristics(1) (continued)
Specifications in standard type face are for TJ = +25°C and those in boldface type apply over the full operating junction
temperature range. Unless otherwise specified: VIN = 48V, FOSC = 250kHz.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Power Good
VDS Required for Power Good Status
VDS Hysteresis of Power Good Status
VGS Required for Power Good Status
1.3
0.8
4.5
1.5
1.0
5.5
30
1.7
1.2
6.5
V
V
V
Default Delay Time of Loss-of Power Good
Status
µs
nPGOOD current Source
nPGOOD Pull Down Resistance
nPGOOD Threshold
45
55
130
2.5
65
250
2.7
µA
Ω
2.3
V
Hot Swap
RDS(ON)
Hot Swap MOSFET Resistance
Hot Swap MOSFET Leakage
Default Inrush Current Limit
Default DC Current Limit
0.7
1.2
110
180
510
610
15
Ω
µA
mA
mA
mA
%
VDS = 4.0V
120
380
470
-15
-12
150
440
540
VDS = 4.0V
VDS = 4.0V
Front Auxiliary DC Current Limit
Inrush Current Limit Programming Accuracy VDS = 4.0V
DC Current Limit Programming Accuracy
Auxiliary Power Option
ICL_FAUX Threshold
VDS = 4.0V
12
%
ICL_FAUX Pin Rising
RAUX Pin Rising
RAUX Pin Rising
8.1
2.3
8.7
50
9.3
3.0
V
µA
V
ICL_FAUX Pull Down Current
RAUX Lower Threshold (I = 22 µA)
RAUX Lower Threshold Hysteresis
RAUX Upper Threshold (I = 250 µA)
RAUX Lower Threshold Current
RAUX Upper Threshold Current
2.5
0.8
6.0
22
V
5.4
16
6.9
28
V
µA
µA
187
250
313
VCC Regulator
VccReg
VCC Regulation (VccReg)
VCC Current Limit
7.4
15
7.7
8
V
mA
mV
VCC UVLO (Rising)
VccReg
– 210
mV
VccReg
– 100 mV
VCC UVLO (Falling)
VIN Supply Current
Supply Current (Icc)
VCC Regulator Dropout
5.9
6.2
6.5
2.0
3
V
mA
mA
V
VCC = 10V
VCC = 10V
(2)
VIN – VCC
6.5
Error Amplifier
Current Limit
Gain Bandwidth
DC Gain
3
MHz
dB
67
Input Voltage
1.225
5
1.275
V
COMP Sink Capability
10
mA
ILIM Delay to Output
30
ns
V
Cycle by Cycle Current Limit Threshold
Voltage
0.45
0.5
0.55
55
Leading Edge Blanking Time
CS Sink Impedance (clocked)
65
35
ns
Ω
(2) The VCC regulator is intended for use solely as a bias supply for the LM5072, dropout assumes 3mA of external VCC current.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
5
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
Electrical Characteristics(1) (continued)
Specifications in standard type face are for TJ = +25°C and those in boldface type apply over the full operating junction
temperature range. Unless otherwise specified: VIN = 48V, FOSC = 250kHz.
Symbol
Soft-start
Parameter
Conditions
Min
8
Typ
Max
12
Units
Soft-start Current Source
10
µA
Oscillator
Frequency1 (RT = 26.1 kΩ)
Frequency2 (RT = 8.7 kΩ)
Sync threshold
175
515
2.6
200
580
3.2
225
645
3.8
KHz
KHz
V
PWM Comparator
Delay to Output
25
ns
%
%
%
Min Duty Cycle
0
Max Duty Cycle (-80 Device)
Max Duty Cycle (-50 Device)
COMP to PWM Comparator Gain
COMP Open Circuit Voltage
COMP Short Circuit Current
75
47
80
50
85
53
0.33
5.2
1.0
4.3
0.6
6.1
1.4
V
mA
Slope Compensation (LM5072-80 Device Only)
Slope Comp Amplitude
70
90
110
mV
Output Section
Output High Saturation
0.25
0.25
18
0.75
0.75
V
V
Output Low Saturation
tr
tf
Rise time
CLOAD = 1nF
ns
ns
Fall time
CLOAD = 1nF
15
PDI Thermal Shutdown(3)
Thermal Shutdown Temp.
Thermal Shutdown Hysteresis
Thermal Resistance
θJA Junction to Ambient
165
25
°C
°C
PWP package
40
°C/W
(3) Device thermal limitations may limit usable range.
6
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
Typical Performance Characteristics
UVLO Threshold vs Temperature
Default Current Limit vs Temperature
475
32.0
31.5
31.0
30.5
30.0
470
465
460
455
450
445
440
435
430
425
-40 -20
0
20 40 60 80 100 120
-40 -20
0
20 40 60 80 100 120
TEMPERATURE (ºC)
TEMPERATURE (ºC)
Figure 2.
Figure 3.
Inrush Current Limit vs ICL_FAUX Resistor
DC Current Limit vs DCCL Resistor
800
800
700
600
500
400
300
200
100
700
600
500
400
300
200
100
115
115
105
95
15 25 35 45 55 65 75 85
105
15 25 35 45 55 65 75 85
95
PROGRAMMING RESISTANCE (kW)
PROGRAMMING RESISTANCE (kW)
Figure 4.
Figure 5.
Programmed DC Current Limit vs Temperature
400
Oscillator Frequency vs Temperature
264
395
390
385
380
375
370
365
360
355
350
262
260
258
256
254
252
250
-40 -20
0
20 40 60 80 100 120
-40 -20
0
20 40 60 80 100 120
TEMPERATURE (ºC)
TEMPERATURE (ºC)
Figure 6.
Figure 7.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Oscillator Frequency vs RT Resistance
Error Amplifier Reference Voltage vs Temperature
1000
900
800
700
600
500
400
300
200
100
0
1.2750
1.2650
1.2550
1.2450
1.2350
1.2250
5
15 25 35 45 55 65 75 85 95 105
-40 -20
0
20 40 60 80 100 120
TEMPERATURE (ºC)
RT RESISTANCE (kW)
Figure 8.
Figure 9.
VCC vs ICC
Input Current vs Input Voltage
3.00E+00
2.50E+00
2.00E+00
1.50E+00
1.00E+00
5.00E-01
0.00E+00
9
8
7
6
5
4
3
2
1
0
V
CC
0
10
20
30
(V)
40
50
60
0
5
10
15
20
I
(mA)
V
CC
IN
Figure 10.
Maximum Duty Cycle vs Temperature
Figure 11.
Soft-start Current vs Temperature
10.5
10.4
10.3
10.2
10.1
10.0
84
83
82
81
80
79
78
-40 -20
0
20 40 60 80 100 120
-40 -20
0
20 40 60 80 100 120
TEMPERATURE (ºC)
TEMPERATURE (ºC)
Figure 12.
Figure 13.
8
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
Specialized Block Diagrams
3
VIN
signature
24.5 kW
2 5V
.
-
+
-
10
VCC
12.0V
1.25V
1.25V
+
5V_PDI
+
-
Threshold VIN=25V
Disable_PDI
-
2.4V
2.0V
+
Threshold VIN= 38V
VIN Hysteresis=6V
-
UVLO
+
1.25V
1.25V
+
EN
-
Auxiliary
Controller
13
11
RAUX
4
5
RCLASS
therma_l limit
50 mA
nPGOOD
+
-
+
-
VCC
2.5V
ICL_FAUX
1
2
9
RT
front_aux
SS
50 mA
OUT
1.25V
+
-
PWM Controller
12 CS
6
7
DCCL
15
14
16
8
COMP
FB
-
Gate
Controller
+
ARTN
RTN
VEE
Hot Swap
MOSFET
Figure 14. Top Level Block Diagram
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
1
Slope
Compensation
Generator
OSC
RT
45mA
0
CLK
Slope
Compensation
disabled for
-50 Device
80% MAX
DUTY LIMIT (-80)
50% MAX
S
R
Q
Q
9
DRIVER
COMP
15
OUT
5V
DUTY LIMIT (-50)
CLR
5k
PWM
100k
50k
1.25V
14
LOGIC
1.4V
SS to Error
Amplifier
FB
10 mA
SS
2
SS
2k
CURRENT
LIMIT
0.5V
12
CS
CLK+ LEB
current sense
65 ns blanking
16
ARTN
Figure 15. PWM Controller Block Diagram
10
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
DESCRIPTION OF OPERATION AND APPLICATIONS INFORMATION
The LM5072 integrates a fully IEEE 802.3af compliant PD interface and PWM controller in a single integrated
circuit, providing a complete and low cost power solution for devices that connect to PoE systems. The
implementation requires a minimal number of external components.
The LM5072’s Hot Swap PD interface provides four major advantages:
1. An input voltage rating up to 100V that allows greater flexibility when selecting a transient surge suppressor
to protect the PD from voltage transients encountered in PoE applications.
2. The integration of the PD signature resistor and other functions including programmable inrush current limit,
input voltage under-voltage lock-out (UVLO), PD classification, and thermal shutdown simplifies PD
implementation.
3. The PD interface and PWM controller accept power from auxiliary sources including AC adapters and solar
cells in various configurations and over a wide range of input voltages. Auxiliary power input can be
programmed to be dominant over PoE power.
4. DC current limit is programmable and adjustable to support PoE applications requiring input currents up to
700 mA.
The LM5072 includes an easy to use PWM controller based on the peak current mode control technique. Current
mode control provides inherent advantages such as line voltage feed-forward, cycle-by-cycle current limit, and
simplified closed-loop compensation. The controller’s PWM gate driver is capable of sourcing and sinking peak
currents of 800 mA to directly drive the power MOSFET switch of the DC-DC converter. The PWM controller also
contains a high gain, high bandwidth error amplifier, a high voltage startup bias regulator, a programmable
oscillator for a switching frequency between 50 kHz to 500 kHz, a bias supply (VCC) under-voltage lock-out
circuit, and a programmable soft-start circuit. These features greatly simplify the design and implementation of
single ended topologies like the flyback, forward and buck.
The LM5072 is available in two versions, the LM5072-50 and LM5072-80. As indicated in the suffix of the part
number, the maximum duty cycle of each device is limited to 50% and 80%, respectively. Internal PWM controller
slope compensation is provided in the LM5072-80 version.
Modes of Operation
Per the IEEE 802.3af specification, when a PD is connected to a PoE system it transitions through several
operating modes in sequence including detection, classification (optional), turn on, normal operation, and power
removal. Each operating mode corresponds to a specific PoE voltage range fed through the Ethernet cable.
Figure 16 shows the IEEE 802.3af specified sequence of operating modes and the corresponding PD input
voltages.
Current steering diode-bridges are required for the PD interface to accept all allowable connections and polarities
of PoE voltage from the RJ-45 connector (see the example application circuits in Figure 31, Figure 32, Figure 33
and Figure 34). The bridge will cause some reduction of the input voltage sensed by the LM5072. To ensure full
compliance to the specification in all operating modes, the LM5072 takes into account the voltage drop across
the bridge diodes and responds appropriately to the voltage received from the PoE cable. Table 1 presents the
response in each operating mode to voltages across the VIN and VEE pins.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
Voltage
42V
30V
Classification
14.5V
10V
Time
2.7V
Discovery
Full Power Application
Classification
Power Removal
Figure 16. Sequence of PoE Operating Modes
Table 1. Operating Modes With Respect To Input Voltage
Mode of Operation
Voltage from PoE Cable per
IEEE 802.3af
LM5072 Input Voltage
(VIN pin to VEE pin)
Detection (Signature)
Classification
2.7V to 10.0V
14.5V to 20.5V
42V max
1.5V to 10.0V
12V to 23.5V
Startup
38V (UVLO Release, VIN Rising)
70V to 32V (UVLO, VIN Falling)
Normal Operation
57V to 36V
Detection Signature
During detection mode, a PD must present a signature resistance between 23.75 kΩ and 26.25 kΩ to the PoE
power sourcing equipment. This signature impedance distinguishes the PD from non-PoE capable equipment to
protect the latter from being accidentally damaged by inadvertent application of PoE voltage levels. To simplify
the circuit implementation, the LM5072 integrates the 24.5 kΩ signature resistor, as shown in Figure 17.
LM5072
VIN
PoE Line
3
Input
24.5k
-
+
12V
PoE Line
7
Return
VEE
Figure 17. Detection Circuit With Integrated PD Signature Resistor
During detection mode, the voltage across the VIN and VEE pins is less than 10V. Once signature mode is
complete, the LM5072 will disengage the signature resistor to reduce power loss in all other modes.
Classification
Classification is an optional feature of the IEEE802.3af specification. It is primarily used to identify the power
requirements of a particular PD device. This feature will allow the PSE to allocate the appropriate available
power to each device on the network. Classification is performed by measuring the current flowing into the PD
during this mode. IEEE 802.3af specifies five power classes, each corresponding to a unique range of
classification current, as presented in Table 2. The LM5072 simplifies the classification implementation by
requiring a single external resistor connected between the RCLASS and VEE pins to program the classification
current. The resistor value required for each class is also given in Table 2.
12
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
Table 2. Classification Levels and Required External Resistor Value
Class
PD Max Power Level
ICLASS Range
LM5072
RCLASS Value
From
To
From
0 mA
To
0 (Default)
0.44W
0.44W
12.95W
3.84W
4 mA
Open
130Ω
71.5Ω
46.4Ω
31.6Ω
1
2
3
4
9 mA
12 mA
20 mA
30 mA
44 mA
3.84W
6.49W
17 mA
26 mA
36 mA
6.49W
12.95W
Reserved
Reserved
LM5072
VIN
PoE Line
Input
3
front_aux
+
-
1.25V
+
EN
-
1.25V
RCLASS
Threshold
VIN = 23.5V
4
7
to UVLO
thermal_limit
R
CLASS
rear_aux
PoE Line
Return
VEE
Figure 18. PD Classification – Fulfilled With a Single External Resistor
Figure 18 shows the LM5072’s implementation of PD classification using an external resistor connected to the
RCLASS pin. During classification, the voltage across the VIN and VEE pins is between 13V and 23.5V. In this
voltage range, the class resistor RCLASS is engaged by enabling the 1.25V buffer amplifier and MOSFET. After
classification is complete, the voltage from the PSE will increase to the normal operating voltage of the PoE
system (48V nominal). When VIN rises above 23.5V, the LM5072 will disengage the RCLASS resistor to reduce
on-chip power dissipation.
The classification feature is disabled when either the front or rear auxiliary power options are selected, as the
classification function is not required when power is supplied from an auxiliary source. The classification function
is also disabled when the LM5072 reaches the thermal shutdown temperature threshold (nominally 165°C). This
may occur if the LM5072 is operated at elevated ambient temperatures and the classification time exceeds the
IEEE802.3af limit of 75 ms.
When the classification option is not required, simply leave the RCLASS pin open to set the PD to the default
Class 0 state. Class 0 requires that the PSE allocate the maximum IEEE802.3af specified power of 15.4 W
(12.95 W at the PD input terminals) to the PD.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
Undervoltage Lockout (UVLO)
The LM5072’s internal preset UVLO circuit continuously monitors the PoE input voltage between the VIN and
VEE pins. When the VIN voltage rises above 38V nominal, the UVLO circuit will release the hot swap MOSFET
and initiate the startup inrush sequence. When the VIN voltage falls below 31V nominal during normal operating
mode, the LM5072 disables the PD by shutting off the hot swap MOSFET.
LM5072
VIN
PoE Line
To Signature
3
Input
and Startup Regulator
To Classification
VIN Threshold =38V
Hysteresis = 7V
UVLO
1.25V
-
thermal_limit
+
front_aux
Gate
Controller
To DC/DC
Converter
Return
PoE Line
Return
7
Hot Swap
MOSFET
VEE
Figure 19. Preset Input UVLO Function
Figure 19 illustrates the block diagram of the LM5072 UVLO circuit. This function requires no external
components. The UVLO signal can be over-ridden by the front auxiliary power option (see details in the RAUX
Option section) to allow the hot swap MOSFET of the LM5072 to pass power from front auxiliary power sources
at voltage levels below the PoE operating voltage. In the rear auxiliary power application (see RAUX Option
section), the auxiliary power source bypasses the hot swap MOSFET and is applied directly to the input of the
DC-DC converter. The UVLO function does not need to be over-ridden in this configuration.
The PD can draw a maximum current of 400 mA during standard 802.3af PoE operation. This current will cause
a voltage drop of up to 8V over a 100m long Ethernet cable. The PD front-end current steering diode bridges
may introduce an additional 2V drop. In order to ensure successful startup at the minimum PoE voltage of 42V,
and to continue operation at the minimum requirement of 36V as specified by IEEE 802.3af, these voltage drops
must be taken into account. Therefore, the LM5072 UVLO thresholds have been set to 38V on the rising edge of
VIN, and 31V on the falling edge of VIN. The 7V nominal hysteresis of the UVLO function, in addition to the
inrush current limit (discussed in the next section), prevents false starts and chattering during startup.
Inrush Current Limit Programming
According to IEEE 802.3af, the input capacitance of the PD power supply must be at least 5 µF (between the
VIN and RTN pins). Considering the capacitor tolerance and the effects of voltage and temperature, a nominal
capacitor value of at least 10 µF is recommended to ensure 5 µF minimum under all conditions. A greater
amount of capacitance may be needed to filter the input ripple of the DC-DC converter. The input capacitors
remain discharged during detection and classification modes of the PD interface. The hot swap MOSFET is
turned on after the VIN minus VEE voltage difference rises above the UVLO release threshold of 38V nominal.
When enabled, the hot swap MOSFET delivers a regulated inrush current to charge the input capacitors of the
DC-DC converter. To prevent excessive inrush current, the LM5072 will turn on the hot swap MOSFET in a
constant current mode. The default, pre-programmed inrush current of 150 mA can be selected by simply leaving
the ICL_FAUX pin open.
14
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
To adjust the capacitor charging time for a particular application requirement, the inrush limit can be programmed
to any value between 150 and 400 mA with an external resistor (RICL) between the ICL_FAUX and VEE pins, as
shown in Figure 20. The relationship between the RICL value and the desired inrush current limit IINRUSH satisfies
the following equation:
100 mA
IINRUSH (mA)
x 127.5 kW
RICL(kW) =
(1)
LM5072
to inrush current limit
1.25V
+
-
ICL_FAUX
5
7
to FAUX
50 mA
R
ICL
VEE
Figure 20. Input Inrush Limit Programming via RICL
The inrush current causes a voltage drop along the PoE Ethernet cable (20Ω maximum) that reduces the input
voltage sensed by the LM5072. To avoid erratic turn-on (hiccups), IINRUSH should be programmed such that the
input voltage drop due to cable resistance does not exceed the VIN-UVLO hysteresis (6V minimum).
DC Current Limit Programming
The LM5072 provides a default DC current limit of 440 mA nominal. This default limit can be selected by leaving
the DCCL pin open.
The LM5072 allows the DC current limit to be programmed within the range from 150 mA to 800 mA. Figure 21
shows the method to program the DC current limit with an external resistor, RDCCL. The relationship between the
RDCCL value and the desired DC current limit IDC satisfies the following equation:
100 mA
IDC (mA)
x 127.5 kW
RDCCL(kW) =
(2)
LM5072
to dc current limit
1.25V
+
-
DCCL
6
7
R
DCCL
VEE
Figure 21. Input DC Current Limit Programming via RDCCL
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
The maximum recommended DC current limit is 800 mA. While thermal analysis should be a standard part of the
module development process, it may warrant additional attention if the DC current limit is programmed to values
in excess of 400 mA. This analysis should include evaluations of the dissipation capability of LM5072 package,
heat sinking properties of the PC Board, ambient temperature, and other heat dissipation factors of the operating
environment.
Power Good and Regulator Startup
The Power Good status indicates that the circuit is ready for PWM controller startup to occur. It is established
when the input capacitors are fully charged through the hot swap MOSFET. Since the hot swap MOSFET is in
series with the input capacitors of the DC-DC converter, its drain-to-source voltage decreases as the charging
occurs. Power Good is indicated when the following two conditions are met: the MOSFET drain-to-source voltage
drops below 1.5V (with 1V hysteresis), and the gate-to-source voltage is greater than 5V. Circuitry internal to the
LM5072 monitors both the drain and gate voltages (see Figure 14), and issues the Power Good status flag by
pulling down the nPGOOD pin to a logic low level relative to the ARTN pin.
The nPGOOD circuitry consists of a 2.5V comparator, a 130Ω pull down MOSFET, and a 50 µA pull up current
source, as shown in Figure 22. Once the Power Good status is established, the nPGOOD pin voltage will be
pulled down quickly by the MOSFET, and the PWM controller will start as soon as the nPGOOD pin voltage
drops below the 2.5V threshold.
LM5072
VCC
10
R
LED
LED to indicate
nPGOOD
50 mA
130W
"Powered from PoE"
C
PGOOD
11
+
-
PWM
DISABLE
2.5V
16
ARTN
Figure 22. "Powered-from-PoE" Indictor and Power Good Delay Timer
The nPGOOD pin can be configured to perform multiple functions. As shown in Figure 22, it can be used to
implement a “Powered from PoE” indicator using an LED with a series current limiting resistor connected to the
VCC pin. This may be useful when the auxiliary power source is directly connected to the DC-DC converter
stage, a situation known as “RAUX” (see Auxiliary Power Options below). In such a configuration, the nPGOOD
pin will be active when the PD is operating from PoE power but not when it is powered from the auxiliary source.
However, the “Powered from PoE” indicator is not applicable in systems implementing the front auxiliary power
configuration “FAUX” (see Auxiliary Power Options below) because both PoE and auxiliary supply current pass
through the hot swap MOSFET. In this configuration, the nPGOOD pin is active when either PoE power or
auxiliary power is applied. The designer should ensure that the current drawn by the LED is not more than a few
milliamps, as the VCC regulator’s output current is limited to 15 mA and must also supply the LM5072’s bias
current and external MOSFET’s gate charging current. Supplying an external VCC that is higher than the
regulated level with a bench supply is an easy way to measure VCC load during normal operation. It should also
be noted that an external load on the VCC line will increase the dropout voltage of the VCC regulator. This may be
a concern when operating from a low voltage rear auxiliary supply.
The nPGOOD pin can also be used to implement a delay timer by adding a capacitor from the nPGOOD pin to
the ARTN pin. This delay timer will prevent the interruption of the PWM controller’s operation in the event of an
intermittent loss of Power Good status. This can be caused by PoE line voltage transients that may occur when
switching between normal PoE power and a backup supply system (e.g. a battery or UPS). This condition will
create a new “hot swap” event if there is a voltage difference between the backup supply and PoE supply. Since
the hot swap MOSFET will likely limit current during such a sudden input voltage change, the nPGOOD pin will
momentarily switch to the ”pull up” state. A capacitor on this pin will delay the transition of the nPGOOD pin state
in order to provide continuous operation of the PWM controller during such transients. The Power Good filter
delay time and capacitor value can be selected with the following equation:
16
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
tPG_Delay (ms)
0.25 ms
0.05mA + ILED (mA)
1mA
x
CPGOOD(nF) =
x 100 nF
(3)
For example, selecting 1000 nF for CPGOOD, the delay time will be 50 ms if no LED is used and about 0.83 ms
when an LED, drawing 3 mA, is used. The delay required for continued operation will depend on the amplitude of
the transient, the DC current limit, the load, and the total amount of input capacitance. Note that this delay does
not ensure continued operation. If the hot swap MOSFET is in current limit for an extended period, it may cause
a thermal limit condition. This will result in a complete shutdown of the switching regulator, though no elements in
the system will be permanently damaged and normal operation will resume momentarily.
The Power Good status will also affect the default DC current limit. Should the sensed drain to source voltage of
the hot swap MOSFET (from ARTN to VEE) exceed 2.5V, the LM5072 will increase the DC current limit from the
default 440 mA to 540 mA, thus allowing the PD to continue operation through the transient event. This higher
current limit will remain in effect until one of the following events occur:
1. the duration of loss of Power Good status exceeds tPG_Delay, at which time the PWM controller will be
disabled,
2. the increased power dissipation in the hot swap MOSFET causes a thermal limit condition as previously
discussed, or
3. the MOSFET drain to source voltage falls below 1.5V to re-establish Power Good status. Under this
condition, the LM5072 will revert back to the default 440 mA DC current limit once Power Good status is
restored. Note that if the DC current limit has been programmed externally with RDCCL (see the DC Current
Limit Programming section), the DC current limit will remain at the programmed level even when the Power
Good status is lost.
Auxiliary Power Options
The LM5072 based PD can receive power from auxiliary sources like AC adapters and solar cells in addition to
the PoE enabled network. This is a desirable feature when the total system power requirements exceed the
PSE’s load capacity. Furthermore, with the auxiliary power option the PD can be used in a standard Ethernet
(non-PoE) system.
For maximum versatility, the LM5072 accepts two different auxiliary power configurations. The first one, shown in
Figure 23, is the front auxiliary (FAUX) configuration in which the auxiliary source is “diode OR’d” with the PoE
potential received from the Ethernet connector. The second configuration, shown in Figure 24, is the rear
auxiliary (RAUX) option in which the auxiliary power bypasses the PoE interface and is connected directly to the
input of the DC-DC converter through a diode. The FAUX option is desirable if the auxiliary power voltage is
similar to the PoE input voltage. However, when the auxiliary supply voltage is much lower than the PoE input
voltage, the RAUX option is more favorable because the current from the auxiliary supply is not limited by the hot
swap MOSFET DC current limit. A comparison of the FAUX and RAUX options is presented in Table 3. Note the
ICL_FAUX and RAUX pins are not reverse voltage protected. If complete reverse protection is desired, series
blocking diodes are necessary.
+V
+PoE
OUT
LM5072
VCC
SS
VIN
RAUX
+ FAUX
RT
ICL_FAUX
COMP
FB
0.1 mF
RCLASS
nPGOOD
OUT
CS
- FAUX
-PoE
DCCL
VEE
ARTN
RTN
Figure 23. The FAUX Configuration
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
+RAUX
+PoE
+V
OUT
VCC
SS
LM5072
VIN
RAUX
RT
ICL_FAUX
COMP
FB
RCLASS
nPGOOD
OUT
CS
DCCL
VEE
ARTN
RTN
-PoE
-RAUX
0.1 mF
Figure 24. The RAUX Configuration
Table 3. Comparison Between FAUX and RAUX Operation
Tradeoff
FAUX Operation
RAUX Operation
Hot Swap Protection / Current Limit
Protection
Automatically provided by the hot swap
MOSFET.
Requires a series resistor to limit the inrush current
during hot swap.
Minimum Auxiliary Voltage
(at the IC pins)
Limited to 18V by the signature detection Only limited by 9V minimum input requirement.
mode, or by the power requirement
(current limit).
Auxiliary Dominance Over PoE
Cannot be forced without external
components.
Can be forced with appropriate RAUX pin
configuration.
Use of nPGOOD Pin as “Powered from
PoE” Indicator
Not applicable as power is delivered
through the hot swap interface in both
PoE and FAUX modes.
Supported.
Transient Protection
Excellent due to active MOSFET current
limit.
Fair due to passive resistor current limit.
The term “Auxiliary Dominance” mentioned in Table 3 means that when the auxiliary power source is connected,
it will always power the PD regardless of the state of PoE power. “Aux dominance” is achievable only with the
RAUX option, as noted in the table.
If the PD is not designed for aux dominance, either the FAUX or RAUX power sources will deliver power to the
PD only under the following two conditions:
1. If auxiliary power is applied before PoE power, it will prevent the PD’s detection by the PSE and will supply
power indefinitely. This occurs because the PoE input bridge rectifiers will be reverse biased, so no detection
signature will be observed. Under this condition, when the auxiliary supply is removed, power will not be
maintained because it will take some time for the PSE to perform signature detection and classification
before it will supply power.
2. If auxiliary power is applied after PoE power is already present but has a higher voltage than PoE, it may
assume power delivery responsibility. Under the second case, if the supplied voltages are comparable, the
load current may be shared inversely proportional to the respective output impedances of each supply. (The
output impedance of the PSE supply is increased by the cable series resistance).
If PoE power is applied first and has a higher voltage than the non-dominant aux power source, it will continue
powering the PD even when the aux power source becomes available. In this case, should PoE power be
removed, the auxiliary source will assume power delivery and supply the DC-DC loads without interruption.
18
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
If either FAUX or RAUX power is supplied prior to PoE power, it will prevent the recognition of the PD by the
PSE. Consequently, continuity of power delivery cannot be ensured because the PoE supply will not be present
when auxiliary power is removed.
FAUX Option
With the FAUX option, the LM5072 hot swap MOSFET provides inrush and DC current limit protection for the
auxiliary power source. To select the FAUX configuration for an auxiliary voltage lower than nominal PoE
voltages, the ICL_FAUX pin must be forced above its high threshold to override the VIN UVLO function. Note
that when the ICL_FAUX pin is pulled high to override VIN UVLO, it also overrides the inrush current limit
programmed by RICL, if present. In this case, the inrush current will revert back to the default 150 mA limit.
Pulling up the ICL_FAUX pin will increase the default DC current limit to 540 mA. This increase in DC current
limit is necessary because higher current is required to support the PD output power at the lower input potentials
observed with auxiliary sources. In cases where the auxiliary supply voltage is comparable to the PoE voltage,
there is no need to pull-up the ICL_FAUX pin to override VIN UVLO, and the default DC current limit remains at
440 mA. However, if the DC current limit is externally programmed with RDCCL, the condition of the ICL_FAUX pin
will not affect the programmed DC current limit. In other words, programmed DC current limit can be considered
a “hard limit” that will not vary in any configuration.
RAUX Option
The RAUX option is desirable when the auxiliary supply voltage is significantly lower than the PoE voltage or
when aux dominance is desired. The inrush and DC current limits of the LM5072 do not protect or limit the RAUX
power source, and an additional resistor in the RAUX input path will be needed to provide transient protection.
To select the RAUX option without aux dominance, simply pull up the RAUX pin to the auxiliary power supply
voltage through a high value resistor. Depending on the auxiliary supply voltage, the resistor value should be
selected such that the current flowing into the RAUX pin is approximately 100 µA when the pin is mid-way
between the lower and upper RAUX thresholds (approximately 4V). For example, with an 18V non-dominant rear
auxiliary supply, the pull up resistor should be:
VAUX - VRAUX
18V - 4V
=
= 140 kW
100 mA
100 mA
(4)
If the PSE load capacity is limited and insufficient, aux dominance will be a desired feature to off load PoE power
for other PDs that do not have auxiliary power available. Aux dominance is achieved by pulling the RAUX pin up
to the auxiliary supply voltage through a lower value (~5 kΩ) resistor that delivers at least 250 µA into the RAUX
pin. When this higher RAUX current level is detected, the LM5072 shuts down the PD interface. In aux dominant
mode, the auxiliary power source will supply the PD system as soon as it is applied. PD operation will not be
interrupted when the aux power source is connected. The PoE source may or may not actually be removed by
the PSE, although the DC current from the network cable is effectively reduced to zero (< 150 µA). IEEE 802.3af
requires the AC input impedance to be greater than 2 MΩ to ensure PoE power removal. This condition is not
satisfied when the auxiliary power source is applied. The PSE may remove power from a port based on the
reduction in DC current. This is commonly known as DC Maintain Power Signature (DC MPS), a common feature
in many PSE systems.
The high voltage startup regulator of the PWM controller does not have low dropout capability and will not be
able to provide VCC when the potential from VIN to RTN is less than 14.5V (no external VCC load). In this case,
the auxiliary voltage should supply VCC directly via diode OR-ing to ensure successful startup.
When using the RAUX configuration, the positive potential connection of the 0.1 µF signature capacitor should be
moved from VIN to RTN/ARTN as shown in Figure 24. This provides a high frequency, low impedance path for
the IC's substrate during rear auxiliary operation. Placing the capacitor here will not affect signature mode.
It should be noted that rear auxiliary non-dominance does not imply PoE dominance. PoE dominance is difficult
to achieve in any PoE system if continuity of power is desired. When the PoE voltage appears, the PSE and PD
interface must continue delivering load current in addition to charging the input capacitor bank from the auxiliary
voltage to the PoE voltage. The situation is further complicated by the fact that for a given delivered power level,
the load current is much higher at the lower input voltages typically used in auxiliary supplies. As is the case
during any inrush sequence, very high power is dissipated in the hot swap MOSFET. Consequently, attempting
to achieve inrush completion while delivering load current is highly ill advised. Lastly, current delivered to the
system may be limited by the PSE, the PD, or both.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
A Note About FAUX and RAUX Pin False Input State Detection
The ICL_FAUX and RAUX pins are used to sense the presence of auxiliary power sources. The input voltage of
each pin must remain low when the auxiliary power sources are absent. However, the Or-ing diodes feeding the
auxiliary power are not ideal and leak reverse current that can flow from the PoE input to both the ICL_FAUX
and RAUX pins. When PoE power is applied, these leakage currents may elevate the potentials of the
ICL_FAUX and RAUX pins to false logic states.
One of two failure modes may be observed when the power diode feeding the front auxiliary input leaks
excessively. First, the current may corrupt the inrush current limit programming, if that feature has been
implemented. Second, the leakage current may elevate the voltage on the pin to the ICL_FAUX input threshold,
which will force UVLO release. This would certainly interrupt any attempt by the LM5072 PD interface to perform
the signature or classification functions.
When the power diode that feeds the rear auxiliary input leaks, the false signal could imply a rear auxiliary supply
is present. In this case, the internal hot swap MOSFET will be turned off. This would of course block PoE power
flow and cause the circuit to prevent startup.
This leakage problem at the control input pins can be easily solved. As shown in Figure 25, an additional pull-
down resistor (Rpd) across each auxiliary power control input provides a path for the diode leakage current so
that it will not create false states on the ICL_FAUX or RAUX pins.
I_leak
Front or Rear
AUX Input
VIN
ICL_FAUX or
RAUX Pin
Rpd
VEE or RTN
Figure 25. Bypassing Resistor – Prevents False ICL_FAUX and RAUX Pin Signaling
High Voltage Startup Regulator
The LM5072 contains a startup bias regulator that allows the VIN pin to be connected directly to PoE network
voltages as high as 100V. The regulator output is connected to the VCC pin, providing an initial DC bias voltage
of 7.7V nominal to start the PWM controller. The regulator is internally current limited to no less than 15 mA to
prevent excessive power dissipation. For VCC voltage stability and noise immunity, a capacitor ranging between
0.1 µF to 10 µF is required between the VCC and ARTN pins. Though the current capability of the regulator
exceeds the requirements of the IC, no external DC load drawing more than 3 mA should be applied to the
output. A small amount of current for a “Powered from PoE” indicator LED (see Power Good and Regulator
Startup section) is acceptable. After the DC-DC converter reaches steady state operation, the VCC voltage is
typically elevated by an auxiliary winding of the power transformer. The sustained VCC voltage should be greater
than 8.1V to ensure the current supplied by the startup regulator is reduced to zero. Increasing the VCC pin
voltage above the regulation level of the startup regulator automatically disables the regulator, thus reducing the
power dissipation inside the LM5072. The power savings can be significant as many high voltage MOSFETs
require a relatively large amount of gate charge and the gate drive current adds directly to the VCC current draw.
A VCC under-voltage lock-out circuit monitors the VCC voltage to prevent the PWM controller from operating as
the VCC voltage rises during startup or falls during shutdown. The PWM controller is enabled when the VCC
voltage rising edge exceeds 7.6V and disabled when the VCC voltage falling edge drops below 6.25V.
Error Amplifier
The LM5072 contains a wide-bandwidth, high-gain error amplifier to regulate the output voltage in non-isolated
applications. The amplifier’s non-inverting input is set to a fixed reference voltage of 1.25V, while the inverting
input is connected to the FB pin. The open-drain output of the amplifier is connected to the COMP pin, which is
pulled up internally through a 5 kΩ resistor to an internal 5V bias voltage. Feedback loop compensation can be
easily implemented by placing the compensation network, represented by “Zcomp”, between the FB and COMP
pins as shown in Figure 26.
20
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
LM5072
Vo
5V
COMP
Zcomp
15
14
R1
R2
5k
to PWM
FB
1.25V
16
SS
ARTN
Figure 26. Internal Error Amplifier – Used for Non-isolated Output Applications
For isolated applications, the error amplifier function is located on the isolated secondary side. The LM5072’s
error amplifier can be disabled by connecting the FB pin to the ARTN pin. As shown in Figure 27, an opto-
coupler is normally used to send the feedback signal across the isolation boundary to the COMP pin. The
internal pull-up resistor on the COMP pin now serves as the pull-up bias for the opto-coupler transistor.
Isolation
Boundary
LM5072
5V
COMP
15
5k
From
Secondary
14
to PWM
FB
Error-
Amplifier
1.25V
16
ARTN
SS
Figure 27. The Internal Error Amplifier – Bypassed in Isolated Output Applications
Current Sense and Limit
The LM5072 CS pin senses the transformer primary current signal for current mode control and current limiting of
the supply. As shown in Figure 28, the current sense function can be fulfilled by a simple sense resistor RSENSE
inserted between the RTN and the source of the primary MOSFET switch.
The RSENSE resistor should be non-inductive, and a low pass filter should be used to reject the switching noise on
the sensed signal. A simple RC filter using 100Ω and 1 nF is typically sufficient. The filter capacitor must be
located close to the CS and ARTN pins. In order to prevent noise propagation and to improve the noise immunity
of the current sense, it is very important to minimize the return path of the current sense signal. This is
accomplished with direct connection to the ARTN pin and a single point connection to the RTN pin on the PC
Board layout.
LM5072
OUT
9
100W
CS
To PWM
Comparator
12
CLK + LEB
1 nF
current sense
65 ns blanking
R
SENSE
16
8
ARTN
RTN
To Drain of Hot
Swap MOSFET
Figure 28. Current Sense Schemes
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
Leading Edge
Narrow Spike
Figure 29. Typical Current Sense Waveform Having a Leading Edge Spike
The current sense signal is also used for cycle-by-cycle over-current protection. When the CS pin signal exceeds
0.5V, the PWM pulse of that cycle will be immediately terminated. The desired cycle-by-cycle over-current
protection level is achieved by selecting the proper value of current sense resistor that produces 0.5V at the CS
pin. For the LM5072-80, the slope compensation reduces the current limit threshold by about 20% maximum at
the 80% maximum duty cycle.
The typical current sense waveform as shown in Figure 29 has a spike at the leading edge. This spike is mainly
caused by the large gate drive current that flows through the current sense resistor at turn-on (up to 0.8A). The
reverse recovery of the rectifier diode on the secondary side and the cross conduction of the primary MOSFET
and sync MOSFET (if used) may also contribute to this leading edge spike. With a relatively small external RC
filter, this spike can still cause a false over-current condition that terminates the PWM output pulse. To avoid this
problem, an internal blanking circuit is provided within the LM5072 as shown in Figure 28. An internal MOSFET
is turned on to short the CS pin to ARTN at the end of each cycle. This MOSFET switch remains on for an
additional 65ns after the beginning of the next PWM cycle, thus blanking out the leading edge spike on the
current sense signal.
Soft-Start
The LM5072 incorporates a soft-start feature which forces the PWM duty cycle to grow progressively during
startup such that the output voltage increases gradually to the steady state level. The soft-start process reduces
or prevents both the surge of inrush current and the associated overshoot of the output voltage during startup.
The LM5072 achieves soft-start using an internal 10 µA current source to charge an external capacitor
connected to the SS pin. The capacitor voltage limits the voltage at the COMP pin which directly controls the
PWM duty cycle. The rate of the soft-start ramp can be adjusted by varying the value of the external capacitor.
Note that the slope of the supply’s output voltage is influenced by the load condition and the total output
capacitance of the supply, as well as the soft-start programming. The supply should be started slowly enough
such that the input current is limited below the hot swap MOSFET DC current limit.
Gate Driver and Maximum Duty Cycle Limit
The LM5072’s gate drive (OUT) pin can source and sink a peak current of 800 mA directly to the gate of the DC-
DC converter’s power MOSFET switch. To serve a variety of applications, the LM5072 is available with two
options for maximum PWM duty cycle. The LM5072-80 operates at duty cycles up to 80% while the LM5072-50
limits the PWM duty cycle to 50%.
Oscillator, Shutdown and Sync Capability
The LM5072 requires a single external resistor connected between the RT and ARTN pins to set the oscillator
frequency (FOSC). The RT timing resistor should be located very close to the IC and connected directly to the RT
and ARTN pins. The following equation describes the relationship between FOSC and the RT resistor value:
200 kHz
RT(kW) =
x 26.2 kW
FOSC (kHz)
(5)
The LM5072 can also be synchronized to an external clock signal with a frequency higher than the programmed
oscillator frequency determined by the RT resistor. The clock signal should be coupled into the RT pin through a
100 pF capacitor, as shown in Figure 30. Successful synchronization requires the peak voltage of the sync pulse
signal to be greater than 3.7V at the RT pin, and pulse width between 15 and 150 ns (set by external
components). The RT resistor is always required, whether the oscillator is operated in “free-running” mode or with
external synchronization.
22
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
LM5072
100 pF
RT
1
to Clock
RT
Synch
Pulse
16
ARTN
Figure 30. Oscillator Synchronization Implementation
Special attention should be paid to the relationship between the oscillator frequency and the PWM switching
frequency. For the LM5072-50 version, the programmed oscillator frequency is internally divided by two in order
to facilitate the 50% duty cycle limit. The PWM output switching frequency is therefore one half of the
programmed oscillator frequency. The frequency divider is not used in the LM5072-80 and therefore the PWM
output frequency is the same as the oscillator frequency. These relationships also apply to external
synchronization frequency versus PWM output frequency.
PWM Comparator / Slope Compensation
The PWM comparator produces the PWM duty cycle by comparing the current sense ramp signal with an error
voltage derived from the error amplifier output. The error amplifier output voltage at the COMP pin is offset by
1.4V and then further attenuated by a 3:1 resistor divider before it is presented to the PWM comparator input.
The PWM duty cycle increases with the voltage at the COMP pin. The controller output duty cycle reduces to
zero when the COMP pin voltage drops below approximately 1.4V.
For duty cycles greater than 50%, current mode control loops are subject to sub-harmonic oscillation. This
instability can be eliminated by adding an additional fixed slope voltage ramp signal to the current sense signal.
This technique is commonly known as “slope compensation”. For the LM5072-80 version with its maximum duty
cycle of 80%, slope compensation is integrated by injecting a 45 μA current ramp from the oscillator into the
current sense signal path (see Figure 15). The 45 μA peak ramping current flows through an internal 2 kΩ
resistor to produce a fixed voltage ramp at the PWM comparator input. Additional slope compensation may be
added by increasing the source impedance of the current sense signal with an external resistor between the CS
pin and the source of the current sense signal. The feature is disabled for the LM5072-50 version because the
duty cycle is limited to 50% and slope compensation is not required.
Thermal Protection
The LM5072 includes internal thermal shutdown circuitry to protect the IC in the event the maximum junction
temperature is exceeded. This circuit prevents catastrophic overheating due to accidental overload of the hot
swap MOSFET or other circuitry. Typically, thermal shutdown is activated at 165°C, causing the hot swap
MOSFET and classification regulator to be disabled. The PWM controller is disabled after the PGOOD timer has
expired. Thermal limit is not enabled unless the module is being powered through the front end and the hot swap
MOSFET is enhanced. VCC current limit provides an adequate level of protection for this 15 mA regulator. The
thermal protection is non-latching, therefore after the temperature drops by the 25°C nominal hysteresis, the hot
swap MOSFET is re-activated and a soft-start is initiated to restore the LM5072 to normal operation. If the cause
of overheating has not been eliminated, the circuit will hiccup in and out of the thermal shutdown mode.
PCB Layout Guidelines
Before processing the Printed Circuit Board (PCB) layout, the engineer should make all necessary adjustments
to the schematic to suite the application. The reader may notice that the LM5072 evaluation board is designed
with dual outputs, both FAUX and RAUX power options, and some re-configuration flexibility features (refer to
Figure 32). However, many devices can be removed for a particular application. Recommendations on
simplifying Figure 32 to suit a given application are as follows:
1. When selecting the FAUX power option only, delete C3, D1, D2, J3, P3, P4, R1, R2, R13, and R29.
2. When selecting the RAUX power option only, delete R30, D3, D7, J2, P1, P2 and R6.
3. When neither FAUX nor RAUX power options are selected, delete all the parts mentioned in (1) and (2)
above.
4. When only a single output is required, delete C11 through C14, C17, D8, J6, J7, L2, R10 and Z4. Modify T1
design to delete the unwanted second output winding and increase the copper used for the single output
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
winding. This re-configuration should make use of the spare pins of the transformer.
5. R24 should be deleted from the schematic completely, being replaced by a short connection for an isolated
application, or by an open for a non-isolated application.
6. Jumpers P5 and P6 (Figure 33) should be deleted from the schematic completely, being replaced by a short
connection for an isolated application, or by an open for a non-isolated application.
7. When the output is non-isolated, delete C20, C22, C25, R7, R11, R16, R17, R24, U2, and U3. Replace C28
with a short connection, and replace P5 and P6 with short connections.
8. One may also modify the number of input and output capacitors to achieve a more optimized design.
Consider the following when starting the PCB design:
1. Try to use both sides of the PCB for part placement to facilitate both layout and routing.
2. Place the power components in a pattern that minimizes the lengths of the high current paths on the PCB.
3. Place the LM5072 and its critical peripheral parts closely. Bypass capacitors and transient protection
elements should be near the LM5072.
4. Route the critical traces first, including both power and signal traces. Make the length of the trace as short as
possible, and avoid excessive use of via holes.
5. Pay attention to grounding issues. Each reference ground should be a copper plane or island. Use via holes
if necessary for direct connections of devices to their appropriate return ground plane or island. Identify the
following ground returns:
–
Primary power return COM: C4, C5, C6, R14, R15, R29, C3, P4, J3-pins 2 and 3, U1-pin 8, C28, and
C29 are all returned to the COM ground plane.
–
Primary control signal return, a ground return island: C19, T1-pin 2, C23, U2-pin 3, R24, C26, C21, and
U1-pin 16 are all returned to this island, and the island should be single point connected to the COM
ground plane.
–
–
Secondary power return IGND: T1-pins 6 and 7, C7 through C10, C12 through C17, C28, Z4, J5, and
J7 are all returned to the IGND ground plane.
Secondary control signal return, a ground return island: R18, U3 and C20 are all returned to this island,
and the island should be single point connected to the IGND ground plane.
Also consider the following during PCB layout and routing.
1. Place the following power components in each group as close as possible:
–
–
–
–
–
C4, C5 (if used), the primary winding of T1, Q1, and R14/R15. The high frequency switching current
(pulse current) flows through these parts in a loop. The physical area enclosed by the loop should be as
small as possible.
D5, C7 through C10, and the secondary winding of T1 for the main output. The high frequency
switching current for the main output rail flows through these parts in a loop. The physical area enclosed
by the loop should be as small as possible.
D8, C12 and C13, and the secondary winding of T1 for the second output, if used. The high frequency
switching current for the second output rail flows through these parts in a loop. The physical area
enclosed by the loop should be as small as possible.
L3, C15, C16, J4 and J5 (if posts are used). L3 should also be as close as possible to the capacitor
bank consisting of C7 through C10 in order to minimize the conduction losses on the PCB. Ceramic
capacitor C15 should be placed directly at the output port.
L2, C14, C17, Z4, J6 and J7 (if posts are used) for the second output rail. L2 should also be as close
as possible to C12 and C13 in order to minimize the conduction losses on the PCB. Ceramic capacitor
C14 should be directly placed at the output port
2. U1 (LM5072) should be placed close to Q1 in the orientation such that the gate drive output pin (OUT, Pin 9)
is close to Q1’s gate.
3. Z2 and C27 must be placed directly across the VIN and VEE pins for best protection against input transients.
In a rear auxiliary application, C27 should be removed and C29 should be installed very close to the RTN
and VEE pins.
4. C19 should be placed directly across the VCC and ARTN pins.
5. C23 should be placed directly across the CS and ARTN pins.
6. R21 should be placed directly across the RT and ARTN pins.
24
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
7. C26 should be placed directly across the SS and ARTN pins.
8. C21 should be placed directly across the nPGOOD and ARTN pins.
9. R25 should be directly routed from the output port.
10. R9 should be directly routed from R14/R15.
11. D6 and Z1 should be placed to achieve the shortest connection from C4 or C5 to the drain pad(s) of Q1 for
better snubbing.
12. C2 and R4 should be placed to achieve the shortest connection across D5.
13. Q1, D5, D8, and U1 (LM5072) should be installed on thermal pads having adequate thermal vias down
through all PCB Layers and an exposed thermal pad on the other side of the PCB.
14. Avoid spiral trace pattern.
15. Avoid placing switching traces near any traces in the regulator feedback loop.
16. Pay attention to trace width. Try to make the power traces as wide as possible. Conversely, do not make
signal traces wider than needed.
After the first placement and routing is completed, make necessary modifications to optimize the design.
Application Example #1
Figure 31 shows an application example of a single isolated output solution for the PD. Both front auxiliary
(FAUX) and rear auxiliary (RAUX) power options are given, although only one option may be needed in practice.
Note that for the RAUX option, D2 is only installed when the supply voltage of the auxiliary power source would
cause the VIN voltage to be below 14.5V.
Figure 31. PD with Isolated, Single Output Solution
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
Application Example #2
Figure 32 shows an example of an isolated, dual-output solution for the PD. The 3.3V output is tightly regulated
while the 5V output is cross-regulated. Both front auxiliary (FAUX) and rear auxiliary (RAUX) power options are
given, although only one option may be needed in practice. Note that for the RAUX option, D2 is only installed
when the supply voltage of the auxiliary power source is lower than 14.5V.
Figure 32. PD with Isolated, Dual Output Solution
26
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
LM5072
www.ti.com
SNVS437D –MARCH 2006–REVISED APRIL 2013
Application Example #3:
Figure 33 shows an application example of the non-isolated version of Figure 31. This non-isolated version saves
many parts used in the isolated feedback example shown in Figure 31. Similar simplification also applies to the
non-isolated version of Figure 32.
Figure 33. PD Solution with Non-Isolated Flyback Topology
Application Example #4
Figure 34 shows an application example of a PD solution using the buck topology. Q2, a dual PNP transistor, is
employed in the output voltage sensing to achieve temperature compensation for the regulated output.
Figure 34. PD Solution with Buck Topology
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Links: LM5072
LM5072
SNVS437D –MARCH 2006–REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (April 2013) to Revision D
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 27
28
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM5072
PACKAGE OPTION ADDENDUM
www.ti.com
7-Oct-2013
PACKAGING INFORMATION
Orderable Device
LM5072MH-50/NOPB
LM5072MH-80/NOPB
LM5072MHX-50/NOPB
LM5072MHX-80/NOPB
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
ACTIVE
HTSSOP
HTSSOP
HTSSOP
HTSSOP
PWP
16
16
16
16
92
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
LM5072
MH-50
ACTIVE
ACTIVE
ACTIVE
PWP
PWP
PWP
92
Green (RoHS
& no Sb/Br)
LM5072
MH-80
2500
2500
Green (RoHS
& no Sb/Br)
LM5072
MH-50
Green (RoHS
& no Sb/Br)
LM5072
MH-80
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
7-Oct-2013
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM5072MHX-50/NOPB HTSSOP PWP
LM5072MHX-80/NOPB HTSSOP PWP
16
16
2500
2500
330.0
330.0
12.4
12.4
6.95
6.95
8.3
8.3
1.6
1.6
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM5072MHX-50/NOPB
LM5072MHX-80/NOPB
HTSSOP
HTSSOP
PWP
PWP
16
16
2500
2500
367.0
367.0
367.0
367.0
35.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
PWP0016A
MXA16A (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
LM5073MH/NOPB
IC 0.93 A SWITCHING REGULATOR, PDSO14, LEAD FREE, TSSOP-14, Switching Regulator or Controller
NSC
LM5073MHX/NOPB
IC 0.93 A SWITCHING REGULATOR, PDSO14, LEAD FREE, TSSOP-14, Switching Regulator or Controller
NSC
©2020 ICPDF网 联系我们和版权申明