LM96163 [TI]
具有 1 条远程和本地通道的温度传感器，带 β 补偿和风扇控制功能;
| 型号： | LM96163 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 具有 1 条远程和本地通道的温度传感器，带 β 补偿和风扇控制功能 温度传感 风扇 传感器 温度传感器 |
| 文件： | 总48页 (文件大小：1028K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
LM96163 Remote Diode Digital Temperature Sensor with Integrated Fan Control and
®
TruTherm BJT Transistor Beta Compensation Technology
Check for Samples: LM96163
1
FEATURES
DESCRIPTION
The LM96163 has remote and local temperature
sensors with integrated fan control that includes
TruTherm BJT transistor beta compensation
technology for remote diode sensing. The LM96163
accurately measures: (1) its own temperature and (2)
the temperature of a diode-connected transistor, such
as a 2N3904, or a thermal diode commonly found on
Computer Processors, Graphics Processor Units
(GPU) and other ASIC's. The LM96163 has an offset
register to correct for errors caused by different non-
ideality factors of other thermal diodes.
2
•
TruTherm BJT Beta Compensation Technology
Supports 45nm, 65nm and 90nm Processor
Remote Diodes
•
•
Factory Trimmed for Intel® 45 nm Processor
Thermal Diodes
Accurately Senses Diode-Connected 2N3904
Transistors or Thermal Diodes On-board Large
Processors or ASIC's
•
•
Accurately Senses its Own Temperature
Integrated PWM Fan Speed Control Output
Supports High Resolution at 22.5kHz
Frequency for 4-pin Fans
The LM96163 also features an integrated, pulse-
width-modulated (PWM), open-drain fan control
output. Fan speed depends on a combination of the
remote temperature reading, the lookup table and
register settings. The 12-step Lookup Table (LUT)
enables the user to program a non-linear fan speed
vs. temperature transfer function often used to quiet
acoustic fan noise. In addition a fully programmable
ramping function has been added to allow smooth
transitions between LUT setpoints.
•
•
Acoustic Fan Noise Reduction with User-
Programmable 12-Step Lookup Table
LUT Transition Fine Resolution Smoothing
Function
•
•
Tachometer Input for Measuring Fan RPM
Smart-Tach Modes for Measuring RPM of Fans
with Pulse-Width-Modulated Power as Shown
in Typical Application
Table 1. Key Specifications
■ Remote Temp Accuracy (includes quantization error)
•
•
•
•
•
•
•
•
ALERT Output for Processor Event
Notification
LM96163 Temp
+25 to +85°C
+25 to +85°C
-40 to +25°C
DiodeTemp
+50 to +105°C
+40 to +125°C
+25 to 125°C
Max Error
±0.75°C
±1.5°C
TCRIT Output for Critical Temperature System
Shutdown
±3.0°C
Offset Register Can Adjust for a Variety of
Thermal Diodes
■ Local Temp Accuracy (includes quantization error)
LM96163 Temp 25°C to 125°C
±3.0°C (max)
10-Bit Plus Sign and 11-Bit Unsigned Formats,
with 1/8°C Resolution
■ Supply Voltage
+3.0 V to +3.6 V
456 µA (typ)
■ Supply Current (0.8Hz Conversion)
Extended Resolution to 1/32°C when Digital
Filter Enabled
Resolves Remote Diode Temperatures up to
255.875°C
SMBus 2.0 Compatible Interface, with
TIMEOUT and ARA
10-Pin SON Package
APPLICATIONS
•
•
Processor Thermal Management
Electronic Test and Office Equipment
Industrial Controls
•
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Connection Diagrams
1
10
TCRIT
VDD
SMBCLK
2
3
4
5
9
8
7
6
SMBDAT
TACH
LM96163
D+
D-
ALERT
PWM
GND
Figure 1. 10-Pin SON (TopView)
See DSC0010A Package
Pin Descriptions
Pin
Name
Input/Output
Function and Connection
Open-Drain Digital Output. Connect to system shutdown. Pin activates when
temperature conversion value exceeds programmed limit. Several power-on-default
limit values are available.
Open-Drain
Digital Output
1
TCRIT
Connect to a low-noise +3.3 ± 0.3 VDC power supply, and bypass to GND with a 0.1 µF
ceramic capacitor in parallel with a 100 pF ceramic capacitor. A bulk capacitance of
10 µF needs to be in the vicinity of the LM96163's VDD pin.
2
VDD
Power Supply Input
Connect to the anode (positive side) of the remote diode. A 100pF capacitor can be
connected between pins 3 and 4.
3
4
D+
Analog Input
Analog Input
Connect to the cathode (negative side) of the remote diode. A 100pF capacitor can be
connected between pins 3 and 4.
D−
Open-Drain
Digital Output
Open-Drain Digital Output. Connect to fan drive circuitry. The power-on default for this
pin is low (pin 4 pulled to ground).
5
6
7
PWM
GND
Ground
This is the analog and digital ground return.
This pin is an open-drain ALERT output.
Open-Drain
Digital Output
ALERT
Tachometer input for measuring fan speed. Note the TACH input is disabled upon
power-up and needs to be enabled for use by setting TCHEN bit 2 of Configuration
Register 03h.
8
TACH
Digital Input
Digital Input/
Open-Drain Digital
Output
9
SMBDAT
SMBCLK
This is the bidirectional SMBus data line.
Digital Input. This is the SMBus clock input.
10
Digital Input
2
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Simplified Block Diagram
Internal Diode
LM96163-LLP10
TruTherm
or
Traditional
Diode
D+
D-
Analog
Filter
IIR
Filter
DS ADC
Bias and
Control
Tachometer
Detection
TACH
TCRIT
Temp Reading,
Temp Limit,
Hysteresis, and
Temp Sensor
SMBDAT
2 - Wire
Serial
Interface
Comparators
SMBCLK
Filter Registers
ALERT
Status and Status Mask Registers and Logic
PWM
PWM Fan Control
Registers
PWM Fan
Control
Typical Application
+3.3V
+3.3V
These two capacitors
are close to Pin 2
4-Pin DC Brushless
Fan Module with
Tachometer Output
and PWM Input
To Processor Power
Supply Shutdown
0.1
1.2k
Fan voltage
+12 or +5 VDC
10 mF
+3.3V
Fan V+
1.2k 1.2k
100 pF
LM96163
1.2k
10
OPTIONAL
Capacitor
is close to
1
To SMBus
TCRIT SMBCLK
interface
control
circuitry
2
3
4
5
9
8
7
6
1k
pins 3 and 4
VDD
SMBDAT
TACH
D+
Tach In
Tach. input
from Fan
100 pF
13k
10k
D-
ALERT
GND
PWM
+3.3V
1.2k
Remote diode-
connected transistor
inside of a Processor
on 45 nm or 65 nm
process
PWM Output
to Fan
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)(3)
Supply Voltage, VDD
−0.3 V to 6.0 V
−0.5 V to 6.0 V
−0.3 V to (VDD + 0. 3 V)
±1 mA
Voltage on SMBDAT, SMBCLK,ALERT, TCRIT, TACH, PWM Pins
Voltage on Other Pins
Input Current, D− Pin(4)
Input Current at All Other Pins(4)
Package Input Current(4)
5 mA
30 mA
SMBDAT, ALERT, PWM pins
Output Sink Current
10 mA
See(5)
Package Power Dissipation
Junction Temperature
125°C
Storage Temperature
−65°C to +150°C
2500 V
Human Body Model
ESD Susceptibility(6)
Machine Model
250 V
Charged Device Model
1000 V
(1) All voltages are measured with respect to GND, unless otherwise noted.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not guarantee performance limits. For guaranteed specifications and test conditions, see the
Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.
(4) When the input voltage (VIN) at any pin exceeds the power supplies (VIN < GND or VIN > V+), the current at that pin should be limited to
5 mA. Parasitic components and/or ESD protection circuitry are shown below for the LM96163's pins. Care should be taken not to
forward bias the parasitic diode, D2, present on pins D+ and D−. Doing so by more than 50 mV may corrupt temperature
measurements.
(5) Thermal resistance junction to ambient when attached to a 2 layer 4"x3" printed circuit board with copper thickness of 2oz. as described
in JEDEC specification EIA/JESD51-3 is 137°C/W. Thermal resistance junction to ambient when attached to a 4 layer 4"x3" printed
circuit board with copper thickness 2oz./1oz./1oz/2oz. and 4 thermal vias as described in JEDEC specification EIA/JESD51-7 is
40.3°C/W.
(6) Human body model, 100 pF discharged through a 1.5 kΩ resistor. Machine model, 200 pF discharged directly into each pin. Charged
Device Model (CDM) simulates a pin slowly acquiring charge (such as from a device sliding down the feeder in an automated
assembler) then rapidly being discharged.
Operating Ratings(1)(2)(3)(4)
Specified Temperature Range (TMIN ≤ TA ≤ TMAX
)
LM96163CISD
–40°C ≤ TA ≤ +85°C
-40°C ≤ TD ≤ +140°C
+3.0 V to +3.6 V
Remote Diode Temperature Range
Supply Voltage Range (VDD
)
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not guarantee performance limits. For guaranteed specifications and test conditions, see the
Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
(2) All voltages are measured with respect to GND, unless otherwise noted.
(3) Soldering process must comply with Reflow Temperature Profile specifications. Refer to www.ti.com/packaging
(4) Reflow temperature profiles are different for packages containing lead (Pb) than for those that do not.
4
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
DC Electrical Characteristics
TEMPERATURE-TO-DIGITAL CONVERTER CHARACTERISTICS
The following specifications apply for VDD = 3.0 VDC to 3.6 VDC, and all analog source impedance RS = 50Ω unless
otherwise specified in the conditions. Boldface limits apply for TA = TJ = TMIN to TMAX; all other limits TA = +25°C; unless
otherwise noted. TD is the junction temperature of the remote thermal diode. TJ is the junction temperature of the LM96163.
Units
(Limits)
Parameter
Conditions
Typical(1) Limits(2)
Temperature Error Using the Remote
Thermal Diode of an Intel Processor on
45nm.(3)
TD = +50°C to +105°C
TD = Remote Diode
Junction Temperature
TA = +25°C to +85°C
±0.75
°C (max)
TA = +25°C to +85°C
TA = -40°C to +25°C
TA = +25°C to +125°C
TA = -40°C to +25°C
TD = +40°C to +125°C
TD = +25°C to +125°C
±1.5
±3.0
°C (max)
°C (max)
°C (max)
Temperature Error Using the Local Diode.
±1
±3
±6
See(4)
&
(5) for the thermal resistance to be
°C (max)
used in the self-heating calculation.
11
0.125
8
Bits
°C
Remote Diode Resolution
Bits
Local Diode Resolution
1
°C
Conversion Time, All Temperature Channels Fastest Setting
38.3
0.4
41.1
ms (max)
V
D− Source Voltage
225
100
µA (max)
µA (min)
µA
(VD+ − VD−) = +0.65 V; High Current
Low Current
172
Diode Source Current
10.75
16
Diode Source Current Ratio
(1) “Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
(2) Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
(3) The accuracy of the LM96163 is guaranteed when using a typical thermal diode of an Intel processor on a 45 nm process, as selected
in the Remote Diode Model Select register. See Typical Performance Characteristics for performance with Intel processor on 65 nm or
90 nm process.
(4) Local temperature accuracy does not include the effects of self-heating. The rise in temperature due to self-heating is the product of the
internal power dissipation of the LM96163 and the thermal resistance.
(5) Thermal resistance junction to ambient when attached to a 2 layer 4"x3" printed circuit board with copper thickness of 2oz. as described
in JEDEC specification EIA/JESD51-3 is 137°C/W. Thermal resistance junction to ambient when attached to a 4 layer 4"x3" printed
circuit board with copper thickness 2oz./1oz./1oz/2oz. and 4 thermal vias as described in JEDEC specification EIA/JESD51-7 is
40.3°C/W.
Operating Electrical Characteristics
Symbol
Parameter
Conditions
Typ(1)
Limits(2)
2.8
Units
V (max)
V (min)
VPOR
Power-On-Reset Threshold Voltage
1.6
SMBus Inactive, 13 Hz
Conversion Rate
1.1
1.6
mA (max)
IS
Supply Current(3)
SMBus Inactive, 0.8 Hz
Conversion Rate
456
416
825
700
µA (max)
µA (max)
STANDBY Mode
(1) “Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
(2) Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
(3) The supply current will not increase substantially with an SMBus transaction.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
AC Electrical Characteristics
The following specifications apply for VDD = 3.0 VDC to 3.6 VDC, and all analog source impedance RS = 50Ω unless
otherwise specified in the conditions. Boldface limits apply for TA = TMIN to TMAX; all other limits TA= +25°C.
Units
(Limit)
Symbol
Parameter
Conditions
Typical(1)
Limits(2)
TACHOMETER ACCURACY
Fan Count Accuracy
±7
% (max)
(max)
kHz
Fan Full-Scale Count
65535
Fan Counter Clock Frequency
Fan Count Update Frequency
90
1.0
Hz
FAN PWM OUTPUT
Frequency Accuracy
±7
% (max)
(1) “Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
(2) Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Digital Electrical Characteristics
Units
Symbol
Parameter
Conditions
Typical(1)
Limits(2)
(Limit)
V (min)
V (max)
µA (max)
µA (max)
pF
VIH
VIL
IIH
Logical High Input Voltage
Logical Low Input Voltage
Logical High Input Current
Logical Low Input Current
Digital Input Capacitance
2.1
0.8
VIN = VDD
0.005
−0.005
5
+10
−10
IIL
VIN = GND
CIN
ALERT, TCRIT and PWM Output
Saturation Voltage
VOL
IOUT = 6 mA
0.4
V (max)
pF
COUT
Digital Output Capacitance
5
(1) “Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
(2) Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
SMBus Logical Electrical Characteristics
The following specifications apply for VDD = 3.0 VDC to 3.6 VDC, and all analog source impedance RS = 50Ω unless
otherwise specified in the conditions. Boldface limits apply for TA = TMIN to TMAX; all other limits TA = +25°C.
Units
(Limit)
Symbol
Parameter
Conditions
Typical(1)
Limits(2)
SMBDAT OPEN-DRAIN OUTPUT
VOL
IOH
Logic Low Level Output Voltage
IOL = 4 mA
VOUT = VDD
0.4
10
V (max)
µA (max)
pF
High Level Output Current
Digital Output Capacitance
0.03
5
COUT
SMBDAT, SMBCLK INPUTS
VIH
VIL
Logical High Input Voltage
2.1
0.8
V (min)
V (max)
mV
Logical Low Input Voltage
Logic Input Hysteresis Voltage
Digital Input Capacitance
VHYST
CIN
320
5
pF
(1) “Typicals” are at TA = 25°C and represent most likely parametric norm. They are to be used as general reference values not for critical
design calculations.
(2) Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
6
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
SMBus Digital Switching Characteristics
Unless otherwise noted, these specifications apply for VDD = +3.0 VDC to +3.6 VDC, CL (load capacitance) on output lines =
80 pF. Boldface limits apply for TA = TJ; TMIN ≤ TA ≤ TMAX; all other limits TA = TJ = +25°C, unless otherwise noted. The
switching characteristics of the LM96163 fully meet or exceed the published specifications of the SMBus version 2.0. The
following parameters are the timing relationships between SMBCLK and SMBDAT signals related to the LM96163. They
adhere to but are not necessarily the same as the SMBus bus specifications.
Units
(Limit)
Symbol
fSMB
tLOW
tHIGH
Parameter
SMBus Clock Frequency
Conditions
Limits(1)
10
100
kHz (min)
kHz (max)
SMBus Clock Low Time
SMBus Clock High Time
From VIN(0) max to VIN(0) max
From VIN(1) min to VIN(1) min
4.7
µs (min)
4.0
50
µs (min)
µs (max)
tR
SMBus Rise Time
SMBus Fall Time
Output Fall Time
See(2)
See(3)
1
µs (max)
µs (max)
ns (max)
tF
0.3
250
tOF
CL = 400 pF, IO = 3 mA
SMBDAT and SMBCLK Time Low for Reset of
Serial Interface(4)
25
35
ms (min)
ms (max)
tTIMEOUT
tSU:DAT
tHD:DAT
Data In Setup Time to SMBCLK High
250
ns (min)
300
1075
ns (min)
ns (max)
Data Out Hold Time after SMBCLK Low
Hold Time after (Repeated) Start Condition. After
this period the first clock is generated.
tHD:STA
tSU:STO
4.0
100
4.7
4.7
µs (min)
ns (min)
µs (min)
µs (min)
Stop Condition SMBCLK High to SMBDAT Low
(Stop Condition Setup)
SMBus Repeated Start-Condition Setup Time,
SMBCLK High to SMBDAT Low
tSU:STA
tBUF
SMBus Free Time between Stop and Start
Conditions
(1) Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
(2) The output rise time is measured from (VIL max - 0.15 V) to (VIH min + 0.15 V).
(3) The output fall time is measured from (VIH min + 0.15 V) to (VIL max - 0.15 V).
(4) Holding the SMBDAT and/or SMBCLK lines Low for a time interval greater than tTIMEOUT will reset the LM96163’s SMBus state machine,
therefore setting SMBDAT and SMBCLK pins to a high impedance state.
tLOW
tR
tF
VIH
SMBCLK V
IL
tHD;STA
tHD;DAT
tSU;STA
tHIGH
tSU;STO
tBUF
tSU;DAT
VIH
VIL
SMBDAT
P
S
S
P
Figure 2. SMBus Timing Diagram for SMBCLK and SMBDAT Signals
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Pin #
Label
TCRIT
VDD
Circuit
Pin ESD Protection Structure Circuits
1
2
3
4
5
6
7
8
9
A
B
B
B
A
B
A
A
A
PIN
D1
SNP
D+
D-
GND
CIRCUIT A
PWM
GND
V+
ALERT
TACH
SMBDAT
D2
PIN
ESD
CLAMP
D3
6.5V
D1
10
SMBCLK
A
GND
CIRCUIT B
8
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Typical Performance Characteristics
Intel Processor on 45nm, 65nm, or 90 nm Process
Thermal Diode Performance Comparison
Remote Temperature Reading Sensitivity to Thermal
Diode Filter Capacitance, TruTherm Enabled
Figure 3.
Figure 4.
Remote Temperature Reading Sensitivity to Thermal
Diode Filter Capacitance, TruTherm Disabled
Thermal Diode Capacitor or PCB Leakage Current Effect
on Remote Diode Temperature Reading
Figure 5.
Figure 6.
Conversion Rate Effect on
Average Power Supply Current
2600
2300
2000
1700
1400
1100
800
500
200
0.01
0.1
1.0
10
100
CONVERSION RATE (Hz)
Figure 7.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
FUNCTIONAL DESCRIPTION
The LM96163 Remote Diode Temperature Sensor with Integrated Fan Control incorporates a ΔVBE-based
temperature sensor utilizing a Local or Remote diode and a 10-bit plus sign ΔΣ ADC (Delta-Sigma Analog-to-
Digital Converter). The LM96163 includes TruTherm BJT beta compensation technology that allows precision
temperature sensing of remote diodes found in sub-micron processes. The pulse-width modulated (PWM) open-
drain output, with a pull-up resistor, is driven by a 12-point temperature to duty cycle look-up table (LUT) and can
directly drive a PWM input of a 4-pin fan in order to modulate it's speed enabling optimum system acoustic
performance. The LM96163 LUT fan control algorithm also includes a smoothing function that allows the PWM
duty cycle to gradually change over a programmed time interval when switching from one level to the next in the
LUT. When running at a frequency of 22.5kHz the PWM output resolution is 0.39%. The LM96163 includes a
TACH input that can measure the speed of a fan using the pulses from a 3 or 4 pin fan’s tachometer output. The
LM96163 includes a smart-tach measurement mode to accommodate the corrupted tachometer pulses when
using switching transistor power drive to modulate the fan speed. The LM96163 has an ALERT open-drain
output that will be pulled low when the measured temperature exceeds certain programmed limits when enabled.
Details are contained in the sections below.
The LM96163's two-wire interface is compatible with the SMBus Specification 2.0 . For more information the
reader is directed to www.smbus.org.
In the LM96163 digital comparators are used to compare the measured Local Temperature (LT) to the Local
High Setpoint user-programmable temperature limit register. The measured Remote Temperature (RT) is digitally
compared to the Remote High Setpoint (RHS), the Remote Low Setpoint (RLS), and the Remote T_CRIT
Setpoint (RCS) user-programmable temperature limits. An ALERT output will occur when the measured
temperature is: (1) higher than either the High Setpoint or the T_CRIT Setpoint, or (2) lower than the Low
Setpoint. The ALERT Mask register allows the user to prevent the generation of these ALERT outputs. A TCRIT
output will occur when the measured temperature is higher than the T_CRIT Setpoint.
The TCRIT function and the look-up table temperature hysteresis can be set separately. The hysteresis value
associated with the TCRIT output is set in the Remote T_CRIT Hysteresis Register. The value associated with
the look-up table function is set in the Lookup Table Hysteresis Register.
The LM96163 may be placed in a low power Standby mode by setting the Standby bit found in the Configuration
Register. In the Standby mode continuous conversions are stopped. In Standby mode the user may choose to
allow the PWM output signal to continue, or not, by programming the PWM Disable in Standby bit in the
Configuration Register.
The Local Temperature reading and setpoint data registers are 8-bits wide. The format of the 11-bit remote
temperature data is a 16-bit left justified word. Two 8-bit registers, high and low bytes, are provided for each
setpoint as well as the temperature reading. A digital filter may be invoked for remote temperature readings that
increases the resolution from 11-bits to 13-bits. The temperature readings are also available in an unsigned
format allowing resolution above 127°C. Two Remote Temperature Offset (RTO) Registers: High Byte and Low
Byte (RTOHB and RTOLB) may be used to correct the temperature readings by adding or subtracting a fixed
value based on a different non-ideality factor and series resistance of the thermal diode if different from the
thermal diode found in the Intel processors on 45 nm process. See section DIODE NON-IDEALITY.
ALERT and TCRIT OUTPUTS
In this section we will address the ALERT and TCRIT active-low open-drain output functions. When the ALERT
Mask bit in the Configuration register is written as zero the ALERT interrupts are enabled.
The LM96163's ALERT pin is versatile and can produce three different methods of use to best serve the system
designer: (1) as a temperature comparator (2) as a temperature-based interrupt flag, and (3) as part of an
SMBus ALERT System. The three methods of use are further described below. The ALERT and interrupt
methods are different only in how the user interacts with the LM96163.
The remote temperature (RT) reading is associated with a T_CRIT Setpoint Register, and both local and remote
temperature (LT and RT) readings are associated with a HIGH setpoint register (LHS and RHS). The RT is also
associated with a LOW setpoint register (RLS). At the end of every temperature reading a digital comparison
determines whether that reading is above its HIGH or T_CRIT setpoint or below its LOW setpoint. If so, the
corresponding bit in the ALERT Status Register is set. If the ALERT mask bit is low, any bit set in the ALERT
Status Register, with the exception of Busy or RDFA, will cause the ALERT output to be pulled low. Any
temperature conversion that is out of the limits defined in the temperature setpoint registers will trigger an
ALERT. Additionally, the ALERT Mask Bit must be cleared to trigger an ALERT in all modes.
10
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
The format of the Remote High limit and T_CRIT limit comparison is programmable. The USF bit found in the
Enhanced Configuration register controls whether comparisons use a signed or unsigned format. The
temperature format used for Remote High and T_CRIT limit comparisons is +255.875 °C to -256 °C.
The three different ALERT modes and TCRIT function will be discussed in the following sections.
ALERT Output as a Temperature Comparator
When the LM96163 is used in a system in which does not require temperature-based interrupts, the ALERT
output could be used as a temperature comparator. In this mode, once the condition that triggered the ALERT to
go low is no longer present, the ALERT is negated (Figure 8). For example, if the ALERT output was activated
by the comparison of LT > LHS, when this condition is no longer true, the ALERT will return HIGH. This mode
allows operation without software intervention, once all registers are configured during set-up. In order for the
ALERT to be used as a temperature comparator, the Comparator Mode bit in the Remote Diode Temperature
Filter and Comparator Mode Register must be asserted. This is not the power-on default state.
Remote High Limit
Remote Diode
Measurement
LM96163 ALERT Pin
Status Register: Remote High
Time
Figure 8. ALERT Output as Temperature Comparator Response Diagram
ALERT Output as an Interrupt
The LM96163's ALERT output can be implemented as a simple interrupt signal when it is used to trigger an
interrupt service routine. In such systems it is desirable for the interrupt flag to repeatedly trigger during or before
the interrupt service routine has been completed. Under this method of operation, during the read of the ALERT
Status Register the LM96163 will set the ALERT Mask bit in the Configuration Register if any bit in the ALERT
Status Register is set, with the exception of Busy and RDFA. This prevents further ALERT triggering until the
master has reset the ALERT Mask bit, at the end of the interrupt service routine. The ALERT Status Register bits
are cleared only upon a read command from the master (see Figure 9 ) and will be re-asserted at the end of the
next conversion if the triggering condition(s) persist(s). In order for the ALERT to be used as a dedicated
interrupt signal, the Comparator Mode bit in the Remote Diode Temperature Filter and Comparator Mode
Register must be set low. This is the power-on default state. The following sequence describes the response of a
system that uses the ALERT output pin as an interrupt flag:
1. Master senses ALERT low.
2. Master reads the LM96163 ALERT Status Register to determine what caused the ALERT.
3. LM96163 clears ALERT Status Register, resets the ALERT HIGH and sets the ALERT Mask bit in the
Configuration Register.
4. Master attends to conditions that caused the ALERT to be triggered. The fan is started, setpoint limits are
adjusted, etc.
5. Master resets the ALERT Mask bit in the Configuration Register.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Remote Diode
Measurement
Remote High Limit
ALERT mask set in
response to reading of
status register by master
LM96163
ALERT pin
End of Temperature
conversion
Status Register: Remote High
Time
Figure 9. ALERT Output as an Interrupt Temperature Response Diagram
ALERT Output as an SMBus ALERT
An SMBus alert line is created when the ALERT output is connected to: (1) one or more ALERT outputs of other
SMBus compatible devices, and (2) to a master. Under this implementation, the LM96163's ALERT should be
operated using the ARA (Alert Response Address) protocol. The SMBus 2.0 ARA protocol, defined in the SMBus
specification 2.0, is a procedure designed to assist the master in determining which part generated an interrupt
and to service that interrupt.
The SMBus alert line is connected to the open-drain ports of all devices on the bus, thereby AND'ing them
together. The ARA method allows the SMBus master, with one command, to identify which part is pulling the
SMBus alert line LOW. It also prevents the part from pulling the line LOW again for the same triggering condition.
When an ARA command is received by all devices on the bus, the devices pulling the SMBus alert line LOW: (1)
send their address to the master and (2) release the SMBus alert line after acknowledgement of their address.
The SMBus Specifications 1.1 and 2.0 state that in response to and ARA (Alert Response Address) “after
acknowledging the slave address the device must disengage its ALERT pulldown”. Furthermore, “if the host still
sees ALERT low when the message transfer is complete, it knows to read the ARA again.” This SMBus
“disengaging ALERT requirement prevents locking up the SMBus alert line. Competitive parts may address the
“disengaging of ALERT” differently than the LM96163 or not at all. SMBus systems that implement the ARA
protocol as suggested for the LM96163 will be fully compatible with all competitive parts.
The LM96163 fulfills “disengaging of ALERT” by setting the ALERT Mask Bit in the Configuration Register after
sending out its address in response to an ARA and releasing the ALERT output pin. Once the ALERT Mask bit is
activated, the ALERT output pin will be disabled until enabled by software. In order to enable the ALERT the
master must read the ALERT Status Register, during the interrupt service routine and then reset the ALERT
Mask bit in the Configuration Register to 0 at the end of the interrupt service routine.
The following sequence describes the ARA response protocol.
1. Master senses SMBus alert line low
2. Master sends a START followed by the Alert Response Address (ARA) with a Read Command.
3. Alerting Device(s) send ACK.
4. Alerting Device(s) send their address. While transmitting their address, alerting devices sense whether their
address has been transmitted correctly. (The LM96163 will reset its ALERT output and set the ALERT Mask
bit once its complete address has been transmitted successfully.)
5. Master/slave NoACK
6. Master sends STOP
7. Master attends to conditions that caused the ALERT to be triggered. The ALERT Status Register is read and
fan started, setpoints adjusted, etc.
8. Master resets the ALERT Mask bit in the Configuration Register.
The ARA, 000 1100, is a general call address. No device should ever be assigned to this address.
The ALERT Configuration bit in the Remote Diode Temperature Filter and Comparator Mode Register must be
set low in order for the LM96163 to respond to the ARA command.
12
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
The ALERT output can be disabled by setting the ALERT Mask bit in the Configuration Register. The power-on
default is to have the ALERT Mask bit and the ALERT Configuration bit low.
Remote High Limit
Remote Diode Measurement
ALERT mask set
in response to
ARA from master
LM96163
ALERT Pin
Status Register: Remote High
Time
Figure 10. ALERT Output as an SMBus ALERT Temperature Response Diagram
TCRIT Function
The TCRIT output will be activated whenever the RCRIT bit in the ALERT Status register is set. This occurs
whenever the remote temperature exceeds the value set by the Remote T_CRIT Setpoint register. There is a
hysteresis associated with the T_CRIT Setpoint that is set by the value in the Remote T_CRIT Hysteresis
register. The RCRIT bit will be reset when the remote temperature equals or is less than the value defined by
Remote T_CRIT Setpoint minus T_CRIT Hysteresis. The resolution of the comparison is 1 °C. For example if
T_CRIT = 110 °C and THYST = 5 °C the TCRIT output will activate when the temperature reading is 111 °C and
deactivate when the temperature reading is 105 °C.
When the LM96163 powers up the T_CRIT limit is locked to the default value. It may be changed after the
T_CRIT Limit Override bit (TCRITOV) bit, found in the Configuration Register, is set.
The format of the Remote T_CRIT setpoint register is controlled by the USF bit found in the Enhanced
configuration register. The temperature reading format used for the T_CRIT comparisons is +255 °C to -256°C.
SMBus INTERFACE
Since the LM96163 operates as a slave on the SMBus the SMBCLK line is an input and the SMBDAT line is
bidirectional. The LM96163 never drives the SMBCLK line and it does not support clock stretching. According to
SMBus specifications, the LM96163 has a 7-bit slave address. All bits, A6 through A0, are internally programmed
and cannot be changed by software or hardware.
The complete slave address is:
A6
1
A5
0
A4
0
A3
1
A2
1
A1
0
A0
0
POWER-ON RESET (POR) DEFAULT STATES
For information on the POR default states see Register Map in Functional Order.
TEMPERATURE DATA FORMAT
Temperature data can only be read from the Local and Remote Temperature value registers. The data format for
all temperature values is left justified 16-bit word available in two 8-bit registers. Unused bits will always report
"0". All temperature data is clamped and will not roll over when a temperature exceeds full-scale value.
Remote temperature and remote high setpoint temperature data can be represented by an 11-bit, two's
complement word or unsigned binary word with an LSb (Least Significant Bit) equal to 0.125°C.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Table 2. 11-bit, 2's complement (10-bit plus sign)
Digital Data
Temperature
Binary
Hex
+125°C
+25°C
+1°C
0111 1101 0000 0000
0001 1001 0000 0000
0000 0001 0000 0000
0000 0000 0010 0000
0000 0000 0000 0000
1111 1111 1110 0000
1111 1111 0000 0000
1110 0111 0000 0000
1100 1001 0000 0000
7D00h
1900h
0100h
0020h
0000h
FFE0h
FF00h
E700h
C900h
+0.125°C
0°C
−0.125°C
−1°C
−25°C
−55°C
Table 3. 11-bit, unsigned binary
Digital Data
Temperature
Binary
Hex
+255.875°C
+255°C
+201°C
+125°C
+25°C
1111 1111 1110 0000
1111 1111 0000 0000
1100 1001 0000 0000
0111 1101 0000 0000
0001 1001 0000 0000
0000 0001 0000 0000
0000 0000 0010 0000
0000 0000 0000 0000
FFE0h
FF00h
C900h
7D00h
1900h
0100h
0020h
0000h
+1°C
+0.125°C
0°C
When the digital filter is enabled on the remote channel, temperature data is represented by a 13-bit unsigned
binary or 12-bit plus sign (two's complement) word with an LSb equal to 0.03125°C.
Table 4. 13-bit, 2's complement (12-bit plus sign)
Digital Data
Temperature
Binary
Hex
+125°C
+25°C
0111 1101 0000 0000
0001 1001 0000 0000
0000 0001 0000 0000
0000 0000 0000 1000
0000 0000 0000 0000
1111 1111 1111 1000
1111 1111 0000 0000
1110 0111 0000 0000
1100 1001 0000 0000
7D00h
1900h
0100h
0008h
0000h
FFF8h
FF00h
E700h
C900h
+1°C
+0.03125°C
0°C
−0.03125°C
−1°C
−25°C
−55°C
Table 5. 13-bit, unsigned binary
Digital Data
Temperature
Binary
Hex
+255.875°C
+255°C
+201°C
+125°C
+25°C
1111 1111 1110 0000
1111 1111 0000 0000
1100 1001 0000 0000
0111 1101 0000 0000
0001 1001 0000 0000
0000 0001 0000 0000
FFE0h
FF00h
C900h
7D00h
1900h
0100h
+1°C
14
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Table 5. 13-bit, unsigned binary (continued)
Digital Data
Binary
Temperature
Hex
+0.03125°C
0°C
0000 0000 0000 1000
0000 0000 0000 0000
0008h
0000h
Local Temperature and Remote T_CRIT setpoint data is represented by an 8-bit, two's complement, word with
an LSb equal to 1°C.
Table 6. 8-bit, 2's complement (7-bit plus sign)
Digital Data
Temperature
Binary
Hex
7Dh
19h
01h
00h
FFh
E7h
C9h
+125°C
+25°C
+1°C
0111 1101
0001 1001
0000 0001
0000 0000
1111 1111
1110 0111
1100 1001
0°C
−1°C
−25°C
−55°C
Remote T_CRIT setpoint data can also be represented by an 8-bit, unsigned, word with an LSb equal to 1°C.
Table 7. 8-bit, unsigned binary
Digital Data
Temperature
Binary
Hex
FFh
96h
7Dh
19h
01h
00h
+255°C
+150°C
+125°C
+25°C
+1°C
1111 1111
1001 0110
0111 1101
0001 1001
0000 0001
0000 0000
0°C
OPEN-DRAIN OUTPUTS
The SMBDAT, ALERT, TCRIT and PWM outputs are open-drain outputs and do not have internal pull-ups. A
“High” level will not be observed on these pins until pull-up current is provided by an internal source, typically
through a pull-up resistor. Choice of resistor value depends on several factors but, in general, the value should
be as high as possible consistent with reliable operation. This will lower the power dissipation of the LM96163
and avoid temperature errors caused by self-heating of the device. The maximum value of the pull-up resistor to
provide the 2.1 V high level is 88.7 kΩ.
DIODE FAULT DETECTION
The LM96163 is equipped with operational circuitry designed to detect remote diode fault conditions:
•
•
•
D+ shorted to VDD
D+ open or floating
D+ shorted to GND.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
In the event that the D+ pin is grounded the Remote Temperature reading is forced to –128.000 °C if signed
format is read and 0 °C if unsigned format is read. When the D+ pin is detected as shorted to VDD or floating, the
Remote Temperature reading is forced to +127.000 °C if signed format is read and +255.000 °C is unsigned
format is read. In addition, the ALERT Status register bit RDFA is set. Setting of the RDFA bit will not cause
ALERT or TCRIT to activate. Under fault conditions remote diode setpoint comparisons will use these forced
temperature values therefore other bits in the ALERT Status Register may be set thus activating the ALERT or
TCRIT outputs unless these bits are masked. The function of the ALERT and TCRIT is fully described in Section
ALERT and TCRIT OUTPUTS.
COMMUNICATING WITH THE LM96163
Each data register in the LM96163 falls into one of four types of user accessibility:
1. Read Only
2. Write Only
3. Read/Write same address
4. Read/Write different address
A Write to the LM96163 is comprised of an address byte and a command byte. A write to any register requires
one data byte.
Reading the LM96163 Registers can take place after the requisite register setup sequence takes place. See
Required Initial Fan Control Register Sequence.
The data byte has the Most Significant Bit (MSB) first. At the end of a read, the LM96163 can accept either
Acknowledge or No-Acknowledge from the Master. Note that the No-Acknowledge is typically used as a signal
for the slave indicating that the Master has read its last byte.
DIGITAL FILTER
In order to suppress erroneous remote temperature readings due to noise as well as increase the resolution of
the temperature, the LM96163 incorporates a digital filter for remote temperature readings. The filter is accessed
in the Remote Diode Temperature Filter and Comparator Mode Register. The filter can be set according to the
following table.
RDTF[1:0]
Filter Setting
0
0
1
1
0
1
0
1
No Filter
Filter (equivalent to Level 2 filter of the LM86/LM89)
Reserved
Enhanced Filter (Filter with transient noise clipping)
Figure 11 describes the filter output in response to a step input and an impulse input.
a) Seventeen and fifty degree step
response
b) Impulse response with input
transients less than 4°C
c) Impulse response with input
transients great than 4°C
Figure 11.
16
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
45
43
41
39
37
35
33
31
29
27
25
LM96163
with
Filter Off
LM96163
with Filter
On
0
50
100
150
200
SAMPLE NUMBER
The filter curves were purposely offset for clarity.
Figure 12. Digital Filter Response in a typical Intel processor on a 65 nm or 90 nm process
Figure 12 shows the filter in use in a typical Intel processor on a 65/90 nm process system. Note that the two
curves have been purposely offset for clarity. Inserting the filter does not induce an offset as shown.
FAULT QUEUE
The LM96163 incorporates a Fault Queue to suppress erroneous ALERT triggering . The Fault Queue prevents
false triggering by requiring three consecutive out-of-limit HIGH or LOW temperature readings. See Figure 13.
The Fault Queue defaults to OFF upon power-up and may be activated by setting the RDTS Fault Queue bit in
the Configuration Register to a 1.
Remote Diode
Measurement
Status Register: Remote High
n
n+1 n+2 n+3 n+4 n+5
SAMPLE NUMBER
Figure 13. Fault Queue Temperature Response Diagram
ONE-SHOT REGISTER
The One-Shot Register is used to initiate a single conversion and comparison cycle when the device is in
standby mode, after which the data returns to standby. This is not a data register. A write operation causes the
one-shot conversion. The data written to this address is irrelevant and is not stored. A zero will always be read
from this register.
SERIAL INTERFACE RESET
In the event that the SMBus Master is reset while the LM96163 is transmitting on the SMBDAT line, the
LM96163 must be returned to a known state in the communication protocol. This may be done in one of two
ways:
1. When SMBDAT is Low, the LM96163 SMBus state machine resets to the SMBus idle state if either SMBDAT
or SMBCLK are held Low for more than 35 ms (tTIMEOUT). Devices are to timeout when either the SMBCLK or
SMBDAT lines are held Low for 25 ms – 35 ms. Therefore, to insure a timeout of devices on the bus, either
the SMBCLK or the SMBDAT line must be held Low for at least 35 ms.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
2. With both SMBDAT and SMBCLK High, the master can initiate an SMBus start condition with a High to Low
transition on the SMBDAT line. The LM96163 will respond properly to an SMBus start condition at any point
during the communication. After the start the LM96163 will expect an SMBus Address address byte.
LM96163 REGISTERS
The following pages include: LM96163 REGISTER MAP IN HEXADECIMAL ORDER, which shows a summary of
all registers and their bit assignments, LM96163 REGISTER MAP IN FUNCTIONAL ORDER, and LM96163
DETAILED REGISTER DESCRIPTIONS IN FUNCTIONAL ORDER, a detailed explanation of each register. Do
not address the unused or manufacturer’s test registers.
LM96163 REGISTER MAP IN HEXADECIMAL ORDER
The following is a Register Map grouped in hexadecimal address order. Some address locations have been left
blank to maintain compatibility with LM86, LM63 and LM64. Addresses in parenthesis are mirrors of “Same As”
address for backwards compatibility with some older software. Reading or writing either address will access the
same 8-bit register.
DATA BITS
Register R/
POR
Val
Register Name
0x[HEX]
W
D7
D6
D5
D4
D3
D2
D1
D0
00
R
–
Local Temperature
(Signed MSB)
LT7
SIGN
LT6
64
LT5
32
LT4
16
LT3
8
LT2
4
LT1
2
LT0
1
01
R
R
–
Rmt Temp MSB
RT12
SIGN
RT11
64
RT10
32
RT9
16
RT8
8
RT7
4
RT6
2
RT5
1
02
03
–
ALERT Status
Configuration
BUSY
LHIGH
STBY
0
RHIGH
0
RLOW
0
RDFA
RCRIT
TACH
R/
W
00
ALTMSK
PWMDIS
TCHEN TCRITOV FLTQUE
04
05
R/
W
08
46
Conversion Rate
Local High Setpoint
[Reserved]
0
0
0
0
CONV3
CONV2
CONV1
CONV0
R/
W
LHS7
SIGN
LHS6
64
LHS5
32
LHS4
16
LHS3
8
LHS2
4
LHS1
2
LHS0
1
06
07
Not Used
R/
W
55
Rmt High Setpoint
MSB
RHS10
SIGN
/128
RHS9
64
RHS8
32
RHS7
16
RHS6
8
RHS5
4
RHS4
2
RHS3
1
08
R/
W
00
00
08
46
Rmt Low Setpoint
MSB
RLS10
SIGN
RLS9
64
RLS8
32
RLS7
16
RLS6
8
RLS5
4
RLS4
2
RLS3
1
(09)
(0A)
(0B)
R/
W
Same as 03
Same as 04
Same as 05
ALTMSK
STBY
PWMDIS
0
0
TCHEN TCRITOV FLTQUE
R/
W
0
0
0
0
CONV3
CONV2
CONV1
CONV0
R/
W
LHS7
SIGN
LHS6
64
LHS5
32
LHS4
16
LHS3
8
LHS2
4
LHS1
2
LHS0
1
0C
R
00
55
[Reserved]
Not Used
(0D)
R/
W
Same as 07
RHS10
SIGN
/128
RHS9
64
RHS8
32
RHS7
16
RHS6
8
RHS5
4
RHS4
2
RHS3
1
(0E)
R/
W
00
Same as 08
One Shot
RLS10
SIGN
RLS9
64
RLS8
32
RLS7
16
RLS6
8
RLS5
4
RLS4
2
RLS3
1
0F
10
W
R
–
–
Write Only. Write command triggers one temperature conversion cycle.
Rmt Temp LSB
(Dig Filter On or Reg
45h STFBE bit set)
RT4
½
RT3
¼
RT2
⅛
RT1
1/16
RT0
1/32
0
0
0
Rmt Temp LSB
(Dig Filter Off)
0
0
11
12
R/
W
00
00
Rmt Temp Offset
MSB
RTO10
SIGN
RTO9
64
RTO8
32
RTO7
16
RTO7
8
RTO5
4
RTO4
2
RTO3
1
R/
W
Rmt Temp Offset
LSB
RTO2
½
RTO1
¼
RTO0
⅛
0
0
0
0
0
18
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
DATA BITS
Register R/
POR
Val
Register Name
0x[HEX]
W
D7
D6
D5
D4
D3
D2
D1
D0
13
R/
W
00
Rmt High Setpoint
LSB
RHS2
½
RHS1
¼
RHS0
⅛
0
0
0
0
0
14
R/
W
00
Rmt Low Setpoint
LSB
RLS2
½
RLS1
¼
RLS0
⅛
0
0
0
1
0
0
15
16
R
00
A4
[Reserved]
Not Used
R/
W
ALERT Mask
1
LHAM
1
RHAM
RLAM
RTAM
TCHAM
17-18
19
R
00
6E
[Reserved]
Not Used
R/
W
Rmt T_CRIT
Setpoint
RCS7
SIGN
/128
RCS6
64
RCS5
32
RCS4
16
RCS3
8
RCS2
4
RCS1
2
RCS0
1
1A–20
21
R
00
0A
[Reserved]
Not Used
R/
W
Rmt T_CRIT
Hysteresis
RTH7
0
RTH6
64
RTH5
32
RTH4
16
RTH3
8
RTH2
4
RTH1
2
RTH0
1
22–2F
30
R
00
02
[Reserved]
Not Used
R/
W
Remote Diode
TruTherm Enable
0
0
0
0
0
0
RDTE
0
31
32
R
–
–
Rmt Temp U-S MSB
RTU12
128
RTU11
64
RTU10
32
RTU9
16
RTU8
8
RTU7
4
RTU6
2
RTU5
1
R
Rmt Temp U-S LSB
Dig Filter On
RTU4
½
RTU3
¼
RTU2
⅛
RTU1
1/16
RTU0
1/32
0
0
0
Rmt Temp U-S LSB
Dig Filter Off
0
0
33
34–44
45
R
R
-
POR Status
[Reserved]
NR
0
0
0
0
0
0
0
0
00
00
Not Used
R/
W
Enhanced Config
STFBE
LRES
PHR
USF
RRS1
RRS0
PSRR
46
47
48
R
R
–
–
Tach Count LSB
Tach Count MSB
Tach Limit LSB
TAC5
TAC13
TACL5
TAC4
TAC12
TACL4
TAC3
TAC11
TACL3
TAC2
TAC10
TACL2
TAC1
TAC9
TAC0
TAC8
TEDGE1 TEDGE0
TAC7 TAC6
Not Used Not Used
R/
W
FF
TACL1
TACL0
0
-
49
4A
R/
W
FF
20
3F
00
17
00
04
Tach Limit MSB
TACL13 TACL12 TACL11 TACL10
TACL9
TACL8
0
TACL7
TACL6
R/
W
PWM and RPM
Config
0
0
0
0
PWPGM
PWOP
PWCKSL
TACH1
TACH0
4B
R/
W
Fan Spin-Up Config
SPINUP SPNDTY SPNDTY SPNTIM2 SPNTIM1 SPNTIM0
1
0
4C
R/
W
PWM Value
HPWVAL HPWVAL PWVAL5 PWVAL4 PWVAL3 PWVAL2 PWVAL1 PWVAL0
7
6
4D
R/
W
PWM Frequency
0
0
0
PWMF4
PWMF3
PWMF2
PWMF1
PWMF0
4E
R/
W
Lookup Table Temp
Offset
0
0
0
0
TO5
32
TO4
16
TO3
8
TO2
4
TO1
2
TO0
1
4F
R/
W
Lookup Table
Hysteresis
0
LOOKH4 LOOKH3 LOOKH2 LOOKH1 LOOKH0
16
8
4
2
1
50–67
R/ 3F, 7F
W
Lookup Table
Lookup Table of up to 12 PWM (3F) and Temp Pairs in 8-bit Registers (7F)
68–BE
BF
R
00
00
[Reserved]
Not Used
R/
W
Rmt Diode Temp
Filter
0
0
0
0
0
RDTF1
RDTF0 ALT/CMP
C0–FD
FE
R
R
R
00
01
49
[Reserved]
Not Used
Manufacturer’s ID
Step/Die Rev. ID
0
0
0
1
0
0
0
0
0
1
0
0
0
0
1
1
FF
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
LM96163 REGISTER MAP IN FUNCTIONAL ORDER
The following is a Register Map grouped in Functional Order. Some address locations have been left blank to
maintain compatibility with LM86. Addresses in parenthesis are mirrors of named address. Reading or writing
either address will access the same 8-bit register. The Fan Control and Configuration Registers are listed first, as
there is a required order to setup these registers first and then setup the others. The detailed explanations of
each register will follow the order shown below. POR = Power-On-Reset.
Register
[HEX]
POR Default
[HEX]
Register Name
Read/Write
FAN CONTROL REGISTERS
45
4A
4B
4D
Enhanced Configuration
PWM and RPM Configuration
R/W
R/W
R/W
R/W
00
20
3F
17
Fan Spin-Up Configuration
PWM Frequency
Read Only
(R/W if Override Bit is Set)
4C
PWM Value
00
4E
4F
Lookup Table Temperature Offset
Lookup Table Hysteresis Temperature
Lookup Table
R/W
R/W
R/W
00
04
50–67
See Table
CONFIGURATION REGISTER
03 (09) Configuration
TACHOMETER COUNT AND LIMIT REGISTERS
R/W
00
46
47
48
49
Tach Count LSB
Tach Count MSB
Tach Limit LSB
Tach Limit MSB
Read Only
Read Only
R/W
N/A
N/A
FF
R/W
FF
LOCAL TEMPERATURE AND LOCAL SETPOINT REGISTERS
00
Local Temperature
Local High Setpoint
Read Only
R/W
N/A
05 (0B)
46 (70°)
REMOTE DIODE TEMPERATURE AND SETPOINT REGISTERS
01
10
Remote Temperature Signed MSB
Remote Temperature Signed LSB
Remote Temperature Unsigned MSB
Remote Temperature Unsigned LSB
Remote Temperature Offset MSB
Remote Temperature Offset LSB
Remote High Setpoint MSB
Read Only
Read Only
Read Only
Read Only
R/W
N/A
N/A
31
N/A
32
N/A
11
00
12
R/W
00
07 (0D)
13
R/W
55 (85°C)
00
Remote High Setpoint LSB
R/W
08 (0E)
14
Remote Low Setpoint MSB
R/W
00 (0°C)
00
Remote Low Setpoint LSB
R/W
19
Remote T_CRIT Setpoint
R/W
6E (110°C)
0A (10°C)
02
21
Remote T_CRIT Hyst
R/W
30
Remote Diode TruTherm Enable
Remote Diode Temperature Filter and Comparator Mode
R/W
BF
R/W
00
CONVERSION AND ONE-SHOT REGISTERS
04 (0A)
0F
Conversion Rate
One-Shot
R/W
08
Write Only
N/A
STATUS AND MASK REGISTERS
02
16
33
ALERT Status
Read Only
R/W
N/A
A4
ALERT Mask
Power On Reset Status
Read Only
N/A
20
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Register
[HEX]
POR Default
Register Name
Read/Write
[HEX]
ID AND TEST REGISTERS
FE
FF
Manufacturer ID
Read Only
Read Only
01
49
Stepping/Die Rev. ID
[RESERVED] REGISTERS—NOT USED
06
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
0C
15
17-18
1A–20
22–29
34–44
68–BE
C0–FD
LM96163 REQUIRED INITIAL FAN CONTROL REGISTER SEQUENCE
Important! The BIOS or firmware must follow the sequence below to configure the following Fan Registers for
the LM96163 before using any of the Fan or Tachometer or PWM registers:
Step
[Register]HEX and Setup Instructions(1)
After power up check to make sure that the Not Ready bit is cleared in the POR Status register [33] bit 7.
Enable or disable Remote Diode TruTherm mode, [30] bit 1.
1
2
3
[4A] Write bits 0 and 1; 3 and 4. This includes tach settings if used, PWM internal clock select (1.4 kHz or 360 kHz) and PWM
Output Polarity.
4
5
[4B] Write bits 0 through 5 to program the spin-up settings.
[4D] Write bits 0 through 4 to set the frequency settings. This works with the PWM internal clock select. If 22.5 kHz is selected
then enhanced fan control functions such as Lookup Table transition smoothing with extended PWM duty cycle resolution is
available and should be setup [45].
6
Choose, then write, only one of the following:
A. [4F–67] the Lookup Table and [4E] the Lookup Table Offset, [45] Lookup Table Temperature Resolution can also be
modified
or
B. [4C] the PWM value bits 0 through 5 or bits 0 through 7 if extended duty cycle resolution is selected.
7
If Step 4A, Lookup Table, was chosen and written then write [4A] bit 5 PWPGM = 0. PWPGM should be set to 1 to enable
writing to the fan control registers listed in this table.
(1) All other registers can be written at any time after the above sequence.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
LM96163 DETAILED REGISTER DESCRIPTIONS IN FUNCTIONAL ORDER
The following is a Register Map grouped in functional and sequence order. New register addresses have been
added to maintain compatibility with the LM63 and LM64 register sets. Addresses in parenthesis are mirrors of
named address for backwards compatibility with some older software. Reading or writing either address will
access the same 8-bit register.
Fan Control Registers
Address Read/
Hex Write
POR
Value
Bits
Name
[Reserved]
STFBE
Description
45HEX ENHANCED CONFIGURATION
R
7
6
0
This bit is unused and always read as 0.
Signed Temperature Filter Bits Enable
0: external signed temperature LSbs [4:3] will always read "0" (backwards
compatible with the LM63)
R/W
0
1: when the digital filter is enabled the external signed temperature LSbs [4:3]
(1/16 and 1/32 resolution) are enabled
Lookup Table Resolution Extension
0: LUT temperature resolution 7-bits (LSb = 1°C, backwards compatible with the
LM63)
1: enable 8-bit LUT temperature resolution (LSb extended to 0.5°C)
R/W
R/W
5
4
0
0
LRES
PHR
22.5kHz PWM High Resolution Control (only effective when PWM frequency set to
22.5kHz)
0: PWM resolution 6.25% (backwards compatible with the LM63)
1: enable high resolution (0.39%)
Unsigned High and T_CRIT Setpoint Format
0: enable signed format for High and T_CRIT setpoints (11-bit is -128.000°C to
127.875°C or 8-bit is -128°C to 127°C)
R/W
3
0
USF
1: enable unsigned format for High and T_CRIT setpoints (11-bit is 0°C to
255.875°C or 8-bit is 0°C to 255°C)
45
PWM Smoothing Ramp Rate Setting (these bits can modified only when PWM
Programming is enabled, 0x4A[5]=1)
00: 0.023 s per step (5.45 seconds for 0 to 100% duty cycle transition with 0.39%
resolution)
01: 0.046 s per step (10.9 seconds for 0 to 100% duty cycle transition with 0.39%
resolution)
R/W
2:1
00
RRS1:RRS0
10: 0.91 s per step (21.6 seconds for 0 to 100% duty cycle transition with 0.39%
resolution)
11: 0.182 s per step (43.7 seconds for 0 to 100% duty cycle transition with 0.39%
resolution)
Note: PWM smoothing is disabled for PWM spinup and for duty cycle setting
override caused by a TCRIT event, thus it is only enabled during LUT transitions.
PWM smoothing is only effective when PWM frequency is set to 22.5kHz.
PWM Smoothing Ramp Rate Control (this bit can modified only when the PWM
Programming is enabled, 0x4A[5]=1)
0: PWM smoothing disabled (LM63 backwards compatible)
R/W
0
0
PSRR
1: enable ramp rate control (as controlled by 0x45[2:1])
Note: PWM smoothing is disabled for PWM spinup and for duty cycle setting
override caused by a TCRIT event, thus it is only enabled during LUT transitions.
PWM smoothing is only effective when PWM frequency is set to 22.5kHz
22
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Address Read/
POR
Value
Bits
Name
Description
Hex
Write
4AHEX FAN PWM AND TACHOMETER CONFIGURATION REGISTER
R
7:6
00
[Reserved]
These bits are unused and always read as 0.
PWM Programming enable
0: the PWM Value (register 0x4C), the PWM Smoothing (0x45[2:0]) and the
Lookup Table (Registers 0x50–0x67) are read-only. The PWM value (0 to 100%) is
determined by the current remote diode temperature and the Lookup Table, and
can be read from the PWM value register.
5
1
PWPGM
1: the PWM value (register 0x4C), the PWM Smoothing (0x45[2:0]) and the Lookup
Table (Registers 0x50–0x67) are read/write enabled. Writing the PWM Value
register will set the PWM output. This is also the state during which the Lookup
Table can be written.
PWM Output Polarity
4
0
PWOP
0: the PWM output pin will be 0V for fan OFF and open for fan ON.
1: the PWM output pin will be open for fan OFF and 0V for fan ON.
PWM Master Clock Select
3
2
0
0
PWCLSL
0: the master PWM clock is 360 kHz
1: the master PWM clock is 1.4 kHz.
4A
[Reserved]
Always write 0 to this bit.
R/W
Tachometer Mode
00: Traditional tach input monitor, false readings when under minimum detectable
RPM. (Smart-TACH mode disabled)
01: Traditional tach input monitor, FFFFh reading when under minimum detectable
RPM. Smart-TACH mode enabled, PWM duty cycle not affected. Use with direct
PWM drive of fan power. TACH readings can cause an error event if TACH
setpoint register is set to less than FFFFh even though fan may be spinning
properly.
10: Most accurate readings, FFFFh reading when under minimum detectable RPM.
Smart-TACH mode enabled, PWM duty cycle modified. Use with direct PWM drive
of fan power. This mode extends the TACH monitoring low RPM sensitivity.
11: Least effort on programmed PWM of fan, FFFF reading when under minimum
detectable RPM. Smart-TACH mode enabled. Use with direct PWM drive of fan
power. This mode extends the TACH monitoring low RPM sensitivity the most.
Note: If the PWM Master Clock is 360 kHz, mode 00 is used regardless of the
setting of these two bits.
1:0
00
TACH1:TACH0
4BHEX FAN SPIN-UP CONFIGURATION REGISTER
R
7:6
0
[Reserved]
These bits are unused and always read as 0
Fast Tachometer Spin-up
If 0, the fan spin-up uses the duty cycle and spin-up time, bits 0–4.
If 1, the LM96163 sets the PWM output to 100% until the spin-up times out (per
bits 0–2) or the minimum desired RPM has been reached (per the Tachometer
Setpoint setting) using the tachometer input, whichever happens first. This bit
overrides the PWM Spin-Up Duty Cycle register (bits 4:3)—PWM output is always
100%. Register x03, bit 2 = 1 for Tachometer mode.
5
1
SPINUP
If PWM Spin-Up Time (bits 2:0) = 000, the Spin-Up cycle is bypassed, regardless
of the state of this bit.
PWM Spin-Up Duty Cycle
00: Spin-Up cycle bypassed (no Spin-Up), unless Fast Tachometer Terminated
SPNDTY1:SPNDT Spin-Up (bit 5) is set.
4B
R/W
4:3
2:0
11
Y0
01: 50%
10: 75%–81% Depends on PWM Frequency. See Applications Notes.
11: 100%
PWM Spin-Up Time Interval
000: Spin-Up cycle bypassed (No Spin-Up)
001: 0.05 seconds
010: 0.1 s
011: 0.2 s
SPNTIM2:SPNTIM
0
111
100: 0.4 s
101: 0.8 s
110: 1.6 s
111: 3.2 s
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Address Read/
Hex Write
POR
Value
Bits
Name
Description
4CHEX PWM VALUE REGISTER
HPWVAL7:HPWV PWM High Resolution and Low Resolution Values
AL6 If PWM Program (register 4A, bit 5) = 0 this register is read only, this register
reflects the LM96163’s current PWM value from the Lookup Table.
7:6
5:0
00
Read
(Write
only if
reg 4A
bit 5 =
1.)
If PWM Program (register 4A, bit 5) = 1, this register is read/write and the desired
PWM value is written directly to this register, instead of from the Lookup Table, for
direct fan speed control.
4C
0x00 PWVAL5:PWVAL0
This register will read 0 during the Spin-Up cycle.
See Application Notes section at the end of this datasheet for more information
regarding the PWM Value and Duty Cycle in %.
4DHEX FAN PWM FREQUENCY REGISTER
R
7:5
000
[Reserved]
These bits are unused and always read as 0
PWM Output Frequency
The PWM Frequency = PWM_Clock / 2n, where PWM Master Clock = 360 kHz or
4D
R/W
4:0
0x17
PWMF4:PWMF0 1.4 kHz (per the PWM Master Clock Select bit in Register 4A), and n = value of the
register. Note: n = 0 is mapped to n = 1. See the Application Note at the end of this
datasheet.
4EHEX LOOKUP TABLE TEMPERATURE OFFSET
R
7:6
00
[Reserved]
TO5:TO0
These bits are unused and always read as 0.
The temperature offset applied to the temperature values of the lookup table. This
offset allows the lookup table temperature settings to be extended above 127°C.
The value, which is always positive, has an unsigned format with 1°C resolution.
The maximum offset that can be programmed is +63°C.
4E
R/W
5:0
0x00
4FHEX LOOKUP TABLE HYSTERESIS
R
7:5
000
[Reserved]
These bits are unused and always read as 0
Lookup Table Hysteresis
4F
R/W
4:0
0x04 LOOKH4:LOOKH0 The amount of hysteresis applied to the Lookup Table. (1 LSb = 1°C, max value
31°C, default value 10°C).
50HEX to 67HEX LOOKUP TABLE (7/8 Bits for Temperature and 6/8 Bits for PWM for each Temperature/PWM Pair)
7
0
E1T7
Lookup Table Temperature Entry 1
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x51. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
50
6:0
0x7F
E1T6:E1T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 1
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x50. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
7:6
5:0
00
E1D7:E1D6
E1D5:E1D0
51
Lookup Table PWM Duty Cycle Entry 1
The PWM value corresponding to the temperature limit in register 0x50 for the low
resolution PWM mode.
0x3F
24
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Address Read/
POR
Value
Bits
Name
Description
Hex
Write
7
0
E2T7
Lookup Table Temperature Entry 2
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x53. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
52
6:0
7:6
0x7F
E2T6:E2T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 2
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x52. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
00
E2D7:E2D6
53
54
55
56
57
Lookup Table PWM Duty Cycle Entry 2
The PWM value corresponding to the temperature limit in register 0x52 for the low
resolution PWM mode.
5:0
7
0x3F
0
E2D5:E2D0
E3T7
Lookup Table Temperature Entry 3
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x55. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
6:0
7:6
0x7F
E3T6:E3T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 3
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x54. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
00
E3D7:E3D6
Lookup Table PWM Duty Cycle Entry 3
The PWM value corresponding to the temperature limit in register 0x54 for the low
resolution PWM mode.
5:0
7
0x3F
0
E3D5:E3D0
E4T7
Lookup Table Temperature Entry 4
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x57. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
6:0
0x7F
E4T6:E4T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 4
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x56. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
7:6
5:0
00
E4D7:E4D6
E4D5:E4D0
Lookup Table PWM Duty Cycle Entry 4
The PWM value corresponding to the temperature limit in register 0x56 for the low
resolution PWM mode.
0x3F
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Address Read/
POR
Value
Bits
Name
Description
Hex
Write
7
0
E5T7
Lookup Table Temperature Entry 5
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x59. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
58
6:0
7:6
0x7F
E5T6:E5T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 5
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x58. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
00
E5D7:E5D6
59
5A
5B
5C
5D
Lookup Table PWM Duty Cycle Entry 5
The PWM value corresponding to the temperature limit in register 0x58 for the low
resolution PWM mode.
5:0
7
0x3F
0
E5D5:E5D0
E6T7
Lookup Table Temperature Entry 6
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x5B. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
6:0
7:6
0x7F
E6T6:E6T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 6
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x5A. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
00
E6D7:E6D6
Lookup Table PWM Duty Cycle Entry 6
The PWM value corresponding to the temperature limit in register 0x5A for the low
resolution PWM mode.
5:0
7
0x3F
0
E6D5:E6D0
E7T7
Lookup Table Temperature Entry 7
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x5D. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
6:0
0x7F
E7T6:E7T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 7
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x5C. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
7:6
5:0
00
E7D7:E7D6
E7D5:E7D0
Lookup Table PWM Duty Cycle Entry 7
The PWM value corresponding to the temperature limit in register 0x5C for the low
resolution PWM mode.
0x3F
26
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Address Read/
POR
Value
Bits
Name
Description
Hex
Write
7
0
E8T7
Lookup Table Temperature Entry 8
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x5F. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
5E
6:0
7:6
0x7F
E8T6:E8T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 8
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x5E. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
00
E8D7:E8D6
5F
60
61
62
63
Lookup Table PWM Duty Cycle Entry 8
The PWM value corresponding to the temperature limit in register 0x5E for the low
resolution PWM mode.
5:0
7
0x3F
0
E8D5:E8D0
E9T7
Lookup Table Temperature Entry 9
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x61. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
6:0
7:6
0x7F
E9T6:E9T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 9
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x60. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
00
E9D7:E9D6
Lookup Table PWM Duty Cycle Entry 9
The PWM value corresponding to the temperature limit in register 0x60 for the low
resolution PWM mode.
5:0
7
0x3F
0
E9D5:E9D0
E10T7
Lookup Table Temperature Entry 10
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x63. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
6:0
0x7F
E10T6:E10T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 10
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x62. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
7:6
5:0
00
E10D7:E10D6
E10D5:E10D0
Lookup Table PWM Duty Cycle Entry 10
The PWM value corresponding to the temperature limit in register 0x62 for the low
resolution PWM mode.
0x3F
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Address Read/
POR
Value
Bits
Name
Description
Lookup Table Temperature Entry 11
Hex
Write
7
0
E11T7
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x65. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
64
6:0
7:6
0x7F
E11T6:E11T0
E11D7:E11D6
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 11
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x64. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
00
65
66
67
Lookup Table PWM Duty Cycle Entry 11
The PWM value corresponding to the temperature limit in register 0x64 for the low
resolution PWM mode.
5:0
7
0x3F
0
E11D5:E11D0
E12T7
Lookup Table Temperature Entry 12
Bit 7 is unused and always set to 0 in the low resolution temperature LUT mode. In
the high resolution temperature LUT mode bit 7 in conjunction with bits 6:0 of this
register are used to determine the limit temperature that the remote diode
temperature is compared to. In high resolution the range is 0°C to 127.5°C. In low
resolution mode the range is 0°C to 127°C. If the remote diode temperature
exceeds this value, the PWM output will be the value in Register 0x67. Only 9-bits
of the temperature reading are used in high resolution and 8-bits in low resolution.
Only positive temperature values can be programed in this register and in all cases
the sign bit is assumed to be zero. Temperatures greater than 127 °C or 127.5 °C
can be programmed through the use of the Lookup Table Temperature Offset
Register (4Eh).
6:0
0x7F
E12T6:E12T0
Read.
(Write
only if
reg 4A
bit 5 =
1)
Lookup Table PWM Duty Cycle Extended Entry 12
These bits are unused and always set to 0 in the low resolution duty cycle LUT
mode. In the high resolution duty cycle LUT mode these bits in association with
bits 5:0 of this register are used for the PWM value associated with the
temperature limit in register 0x66. These bits can only be activated when PWM
frequency of 22.5kHz is chosen.
7:6
5:0
00
E12D7:E12D6
E12D5:E12D0
Lookup Table PWM Duty Cycle Entry 12
The PWM value corresponding to the temperature limit in register 0x66 for the low
resolution PWM mode.
0x3F
28
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Configuration Register
Address Read/
Hex Write
POR
Value
Bits
Name
Description
03 (09)HEX CONFIGURATION REGISTER
ALERT Mask
0: ALERT interrupts are enabled.
1: ALERT interrupts are masked, and the ALERT pin is always in a high
impedance (open) state.
7
6
0
ALTMSK
STBY
Standby
0: the LM96163 is in operational mode, converting, comparing, and updating the
PWM output continuously.
1: the LM96163 enters a low power standby mode.
In standby, continuous conversions are stopped, but a conversion/comparison
cycle may be initiated by writing any value to register 0x0F the One-shot Register.
Operation of the PWM output in standby depends on the setting of bit 5 in this
register.
0
R/W
PWM Disable in Standby
0: the LM96163’s PWM output continues to output the current fan control signal
5
0
PWMDIS
while in STANDBY.
1: the PWM output is disabled (as defined by the PWM polarity bit) while in
STANDBY.
03 (09)
R
4:3
2
00
0
[Reserved]
TCHEN
This bit is unused and always read as 0.
TACH Enable
0: disables the TACH input
1: enables the TACH input
T_CRIT Limit Override
1
0
0
0
TCRITOV
FLTQUE
0: locks the T_CRIT limit for the remote diode, POR setting is nominally 110°C
1: unlocks the T_CRIT limit and allows it to be reprogrammed multiple times
R/W
RDTS Fault Queue
0: an ALERT will be generated if any Remote Diode conversion result is above the
Remote High Set Point or below the Remote Low Setpoint.
1: an ALERT will be generated only if three consecutive Remote Diode
conversions are above the Remote High Set Point or below the Remote Low
Setpoint.
Tachometer Count and Limit Registers
Address Read/
Hex Write
POR
Value
Bits
Name
Description
47HEX TACHOMETER COUNT (MSB) and 46HEX TACHOMETER COUNT (LSB) REGISTERS (16 bits: Read LSB first to lock MSB and
ensure MSB and LSB are from the same reading)
47
R
7:0
N/A
TAC13:TAC6
Tachometer Count (MSB and LSB)
These registers contain the current 16-bit Tachometer Count, representing the
period of time between tach pulses.
Note that the 16-bit tachometer MSB and LSB register addresses are in reverse
order from the 16 bit temperature readings.
R
7:2
N/A
TAC5:TAC0
Tachometer Edge Programming
Bits
00:
01:
10:
11:
Edges Used
Tach_Count_Multiple
Reserved - do not use
46
2
3
5
4
2
1
R
1:0
00
TEDGE1:TEDGE0
Note: If PWM_Clock_Select = 360 kHz, then Tach_Count_Multiple = 1 regardless
of the setting of these bits.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Address Read/
Hex Write
POR
Value
Bits
Name
Description
49HEX TACHOMETER LIMIT (MSB) and 48HEX TACHOMETER LIMIT (LSB) REGISTERS
49
R/W
R/W
R/W
7:0
7:2
1:0
0xFF
0xFF
TACL13:TACL6
TACHL5:TACL0
[Reserved]
Tachometer Limit (MSB and LSB)
These registers contain the current 14-bit Tachometer Count, representing the
period of time between tach pulses. Fan RPM = (f * 5,400,000) / (Tachometer
Count), where f = 1 for 2 pulses/rev fan; f = 2 for 1 pulse/rev fan; and f = 2/3 for 3
pulses/rev fan. See the Applications Notes section for more tachometer
information. Note that the 16-bit tachometer MSB and LSB register addresses are
in reverse order from the 16 bit temperature readings.
48
These bits are not used and write 0 or 1.
Local Temperature and Local High Setpoint Registers
Address Read/
Hex Write
POR
Value
Bits
Name
Description
00HEX LOCAL TEMPERATURE REGISTER (8-bits)
Local Temperature Reading (8-bit)
8-bit integer representing the temperature of the LM96163 die.
LT7 is the SIGN bit
LT6 has a bit weight of 64°C
LT5 has a bit weight of 32°C
LT4 has a bit weight of 16°C
LT3 has a bit weight of 8°C
00
R
7:0
N/A
LT7:LT0
LT2 has a bit weight of 4°C
LT1 has a bit weight of 2°C
LT0 has a bit weight of 1°C
05 (0B)HEX LOCAL HIGH SETPOINT REGISTER (8-bits)
Local HIGH Setpoint
High Setpoint for the internal diode.
LHS7 is the SIGN bit
LHS6 has a bit weight of 64°C
LHS5 has a bit weight of 32°C
LHS4 has a bit weight of 16°C
LHS3 has a bit weight of 8°C
LHS2 has a bit weight of 4°C
LHS1 has a bit weight of 2°C
LHS0 has a bit weight of 1°C
0x46
(70°)
05
R/W
7:0
LHS7:LHS0
Remote Diode Temperature, Offset and Setpoint Registers
Address Read/
Hex Write
POR
Value
Bits
Name
Description
01HEX AND 10HEX SIGNED REMOTE DIODE TEMPERATURE REGISTERS
Most Significant Byte of the Signed Remote Diode Temperature Reading
The most significant 8-bits of the 2’s complement value, representing the
temperature of the remote diode connected to the LM96163. Bit 7 is the sign bit,
bit 6 has a weight of 64°C, and bit 0 has a weight of 1°C. This byte to be read
before the LSB.
01
10
R
R
7:0
N/A
RT12:RT5
Least Significant Byte of the Signed Remote Diode Temperature Reading
This is the LSB of the 2’s complement value, representing the temperature of the
remote diode connected to the LM96163. RT4 has a weight 0.5°C, RT3 has a
weight of 0.25°C, and RT2 has a weight of 0.125°C. If the digital filter is turned off
RT1:RT0 have a value of 00 unless extended resolution (Reg 45h STFBE bit set)
is enabled. If extended resolution is chosen, for readings greater than 127.875
RT1:RT0=11 and for other cases RT1:RT0=00. When the digital filter is turned on
and extended resolution enabled: RT1 has a weight of 0.0625 and RT0 has a
weight of 0.03125°C
7:3
2:0
N/A
00
RT4:RT0
[Reserved]
These bits are unused and always read as 0.
30
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
Address Read/
POR
Value
Bits
Name
Description
Hex
Write
31HEX AND 32HEX UNSIGNED REMOTE DIODE TEMPERATURE REGISTERS
Most Significant Byte of the Unsigned Format Remote Diode Temperature
Reading
The most significant 8-bits of the unsigned format value, representing the
temperature of the remote diode connected to the LM96163. Bit 7 has a weight of
128°C, bit 6 has a weight of 64°C, and bit 0 has a weight of 1°C. This byte to be
read before the LSB.
31
32
R
R
7:0
N/A
RTU12:RTU5
Least Significant Byte of the Unsigned Format Remote Diode Temperature
Reading
This is the LSB of the unsigned value, representing the temperature of the remote
diode connected to the LM96163. Bit 4 has a weight 0.5°C, bit 3 has a weight of
0.25°C, and bit 2 has a weight of 0.125°C. if the digital filter is turned off
RUT1:RUT0 have a value of 00. When the digital filter is turned on: bit 1 has a
weight of 0.0625 and bit 0 has a weight of 0.03125°C
7:3
2:0
N/A
00
RUT4:RUT0
[Reserved]
These bits are unused and always read as 0.
11HEX AND 12HEX REMOTE TEMPERATURE OFFSET REGISTERS
11
R/W
R/W
R
7:0
7:5
4:0
0x00
000
000
RTO10:RTO3
RTO2:RTO1
[Reserved]
Remote Temperature Offset (MSB and LSB)
These registers contain the value added to or subtracted from the remote diode’s
reading to compensate for the different non-ideality factors of different
processors, diodes, etc. The 2’s complement value, in these registers is added to
the output of the LM96163’s ADC to form the temperature reading contained in
registers 01 and 10. These registers have the same format as the MSB and LSB
Remote Diode Temperature Reading registers with the digital filter off.
12
These bits are not used and always read as 0.
07 (0D)HEX AND 13HEX REMOTE HIGH SETPOINT REGISTERS
0x55
(85°C)
Remote HIGH Setpoint (MSB and LSB)
07 (0D)
R/W
7:0
RHS10:RHS3
High setpoint temperature for remote diode. Same format as Unsigned Remote
Temperature Reading (registers 31 and 32) or Signed Remote Temperature
Reading (registers 01 and 10) with the digital filter off. Is it programmable by the
USF bit found in the Enhanced configuration Register.
R/W
R
7:5
4:0
000
RHS2:RHS0
[Reserved]
13
0x00
These bits are not used and always read as 0.
08 (0E)HEX AND 14HEX REMOTE LOW SETPOINT REGISTERS
00
(0°C)
Remote LOW Setpoint (MSB and LSB)
Low setpoint temperature for remote diode. Same format as Signed Remote
Temperature Reading (registers 01 and 10) with the digital filter off.
08 (0E)
14
R/W
7:0
RTS10:RTS3
R/W
R
7:5
4:0
000
RTS2:RTS0
[Reserved]
0x00
These bits are not used and always read as 0.
19HEX REMOTE DIODE T_CRIT SETPOINT REGISTER
Remote Diode T_CRIT Setpoint Limit
This 8-bit integer stores the T_CRIT limit and is nominally 110°C. The value of
this register can be locked by setting T_CRIT Limit Override (bit 1) in the
Configuration register to a 0, then programming a new T_CRIT value into this
register. The format of this register is programmable. When the USF bit in the
Enhanced Configuration register is cleared:
LCS7 is the SIGN bit
0x6E
(110°
C)
19
R/W
7:0
RCS7:RCS0
LCS6 has a bit weight of 64°C
LCS5 has a bit weight of 32°C
LCS4 has a bit weight of 16°C
LCS3 has a bit weight of 8°C
LCS2 has a bit weight of 4°C
LCS1 has a bit weight of 2°C
LCS0 has a bit weight of 1°C
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Address Read/
Hex Write
POR
Value
Bits
Name
Description
21HEX T_CRIT HYSTERESIS REGISTER
7
RTH7
This bit is unused. OK to write 1 or 0.
Remote Diode T_CRIT Hysteresis
T_CRIT stays activated until the remote diode temperature goes below [(T_CRIT
Limit)—(T_CRIT Hysteresis)].
RTH6 has a bit weight of 64°C
RTH5 has a bit weight of 32°C
RTH4 has a bit weight of 16°C
0x0A
(10°C)
21
R/W
6:0
RTH6:RTH0
RTH3 has a bit weight of 8°C
RTH2 has a bit weight of 4°C
RTH1 has a bit weight of 2°C
RTH0 has a bit weight of 1°C
30HEX REMOTE DIODE TruTherm ENABLE REGISTER
R
R/W
R
7:2
0x00
[Reserved]
These bits are unused and always read as 0.
Remote Diode TruTherm Enable
0: TruTherm beta compensation technology is turned off. Use this mode when
using an MMBT3904 as a thermal diode.
1: TruTherm beta compensation technology is turned on. Use this mode when
sensing a thermal diode in an Intel processor on 45 nm or 65 nm process.
30
1
1
0
RDTE
0
[Reserved]
This bit is unused and always read as 0.
BFHEX REMOTE DIODE TEMPERATURE FILTER AND COMPARATOR MODE
R/W
R
7:6
5:3
00
[Reserved]
[Reserved]
These bits are unused and always write 0.
These bits are unused and always read as 0.
000
Remote Diode Temperature Filter Control
00: Filter Disabled
01: Filter Level 2 (minimal filtering, same as 10; Like LM63, LM63 Level 1 not
2:1
00
0
RDTF1:RDTF0
ALT/CMP
supported)
BF
10: Filter Level 2 (minimal filtering, same as 01; like LM63, LM63 Level 1 not
supported)
11: Filter Enhanced Level 2 (maximum filtering)
R/W
Comparator Mode
0: the ALERT pin functions normally.
1: the ALERT pin behaves as a comparator, asserting itself when an ALERT
condition exists, de-asserting itself when the ALERT condition goes away.
0
32
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
ALERT Status and Mask Registers
Address Read/
Hex Write
POR
Value
Bits
Name
Description
02HEX ALERT STATUS REGISTER (8-bits) (All Alarms are latched until read, then cleared if alarm condition was removed at the
time of the read.)
Busy
7
0
BUSY
0: the ADC is not converting.
1: the ADC is performing a conversion. This bit does not affect ALERT status.
Local High Alarm
0: the internal temperature of the LM96163 is at or below the Local High Setpoint.
1: the internal temperature of the LM96163 is above the Local High Setpoint, and
an ALERT is triggered.
6
5
4
0
0
0
LHIGH
[Reserved]
RHIGH
This bit is unused and always read as 0.
Remote High Alarm
0: the temperature of the Remote Diode is at or below the Remote High Setpoint.
1: the temperature of the Remote Diode is above the Remote High Setpoint, and
an ALERT is triggered.
Remote Low Alarm
0: the temperature of the Remote Diode is at or above the Remote Low Setpoint.
1: the temperature of the Remote Diode is below the Remote Low Setpoint, and
an ALERT is triggered.
3
2
0
0
RLOW
RDFA
0x02
R
Remote Diode Fault Alarm
0: the Remote Diode appears to be correctly connected.
1: the Remote Diode may be disconnected or shorted to ground. This Alarm does
not trigger an ALERT or a TCRIT.
Remote T_CRIT Alarm
When this bit is a 0, the temperature of the Remote Diode is at or below the
T_CRIT Limit.
When this bit is a 1, the temperature of the Remote Diode is above the T_CRIT
Limit, ALERT and TCRIT are triggered.
1
0
0
0
RCRIT
TACH
Tach Alarm
When this bit is a 0, the Tachometer count is lower than or equal to the
Tachometer Limit (the RPM of the fan is greater than or equal to the minimum
desired RPM).
When this bit is a 1, the Tachometer count is higher than the Tachometer Limit
(the RPM of the fan is less than the minimum desired RPM), and an ALERT is
triggered.
16HEX ALERT MASK REGISTER (8-bits)
R
R/W
R
7
6
5
4
1
0
1
0
[Reserved]
This bit is unused and always read as 1.
Local High Alarm Mask
0: a Local High Alarm event will generate an ALERT.
1: a Local High Alarm will not generate an ALERT
LHAM
[Reserved]
RHAM
This bit is unused and always read as 1.
Remote High Alarm Mask
0: Remote High Alarm event will generate an ALERT.
1: a Remote High Alarm event will not generate an ALERT.
R/W
R
Remote Low Alarm Mask
0: a Remote Low Alarm event will generate an ALERT.
1: a Remote Low Alarm event will not generate an ALERT.
16
3
2
1
0
1
0
RLAM
[Reserved]
RTAM
This bit is unused and always read as 1.
Remote T_CRIT Alarm Mask
0: a Remote T_CRIT event will generate an ALERT.
1: a Remote T_CRIT event will not generate an ALERT.
R/W
TACH Alarm Mask
0
0
TCHAM
When this bit is a 0, a Tach Alarm event will generate an ALERT.
When this bit is a 1, a Tach Alarm event will not generate an ALERT.
33HEX POWER ON RESET STATUS REGISTER
Power On Reset Status
7
NR
0: Power On Reset cycle over part ready
1: Power On Reset cycle in progress part not ready
33
R
—
6:0
[Reserved]
These bits are unused and will always report 0.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
33
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Conversion Rate and One-Shot Registers
Address Read/
Hex Write
POR
Value
Bits
Name
Description
04 (0A)HEX CONVERSION RATE REGISTER (8-bits)
R
7:4
[Reserved]
These bits are unused and will always be set to 0.
Conversion Rate
Sets the conversion rate of the LM96163.
0000 = 0.05 Hz
0001 = 0.1 Hz
0010 = 0.204 Hz
0011 = 0.406 Hz
0100 = 0.813 Hz
0101 = 1.625 Hz
0110 = 3.25 Hz
04 (0A)
0x08
R/W
3:0
CONV3:CONV0
0111 = 6.5 Hz
1000 = 13 Hz
1001 = 26 Hz
All other values = 26 Hz
0FHEX ONE-SHOT REGISTER (8-bits)
One Shot Trigger
Write
Only
0F
7:0
N/A
With the LM96163 in the STANDBY mode a single write to this register will
initiate one complete temperature conversion cycle. Any value may be written.
ID Registers
Address Read/
POR
Value
Bits
Name
Description
Hex
Write
FEHEX MANUFACTURER’S ID REGISTER (8-bits)
FE 7:0 0x01 Manufacturer’s ID 0x01 = National Semiconductor
R
FFHEX STEPPING / DIE REVISION ID REGISTER (8-bits)
Stepping/Die
Revision ID
FF
R
7:0
0x49
Version of LM96163
34
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
APPLICATION NOTES
FAN CONTROL DUTY CYCLE VS. REGISTER SETTINGS AND FREQUENCY
NOTE
The following table is true only when the 22.5 kHz PWM frequency high resolution duty
cycle is not selected.
PWM
Freq at
360 kHz
Internal
Clock, kHz
PWM
Freq at
1.4 kHz
Internal
Clock, Hz
Actual Duty
Cycle, %
When
75% is
Selected
PWM
Freq
4D
PWM
Value
4C [5:0]
for 100%
PWM
Value
4C [5:0] for
about 75%
PWM
Value
4C [5:0]
for 50%
Step
Resolution,
%
[4:0]
0
Address 0 is mapped to Address 1
1
50
2
1
1
180.0
703.1
351.6
234.4
175.8
140.6
117.2
100.4
87.9
78.1
70.3
63.9
58.6
54.1
50.2
46.9
43.9
41.4
39.1
37.0
35.2
33.5
32.0
30.6
29.3
28.1
27.0
26.0
25.1
24.2
23.4
22.7
50.0
75.0
2
25
4
3
2
90.00
60.00
45.00
36.00
30.00
25.71
22.50
20.00
18.00
16.36
15.00
13.85
12.86
12.00
11.25
10.59
10.00
9.47
3
16.7
12.5
10.0
8.33
7.14
6.25
5.56
5.00
4.54
4.16
3.85
3.57
3.33
3.13
2.94
2.78
2.63
2.50
2.38
2.27
2.17
2.08
2.00
1.92
1.85
1.79
1.72
1.67
1.61
6
5
3
83.3
4
8
6
4
75.0
5
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
8
5
80.0
6
9
6
75.0
7
11
12
14
15
17
18
20
21
23
24
26
27
29
30
32
33
35
36
38
39
41
42
44
45
47
7
78.6
8
8
75.0
9
9
77.8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
75.0
77.27
75.00
76.92
75.00
76.67
75.00
76.47
75.00
76.32
75.00
76.19
75.00
76.09
75.00
76.00
75.00
75.93
75.00
75.86
75.00
75.81
9.00
8.57
8.18
7.82
7.50
7.20
6.92
6.67
6.42
6.21
6.00
5.81
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
35
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
NOTE
The following table is true only when the 22.5 kHz PWM frequency with high resolution
duty cycle is selected by setting bit 4 (PHR) of the Enhanced Configuration register
(0x45), clearing bit 3 (PWCKSL) of the PWM and RPM Configuration register (0x4A) and
setting PWM Frequency (0x4D) register to 0x08.
Actual Duty
Cycle, %
When
Approximately
75% is
PWM
Value
4C [7:0]
for 100%
(Hex)
PWM
Value
4C [7:0] for
about 75%
(Hex)
PWM
Value
4C [7:0]
for 50%
(Hex)
PWM
Freq at
360 kHz
Internal
Clock, kHz
PWM
Freq at
1.4 kHz
Internal
Clock, Hz
PWM
Freq
4D
Step
Resolution,
%
[4:0]
Selected
8
0.392
FF
BF
80
22.50
Not Available
74.902
Computing Duty Cycles for a Given Frequency
Select a PWM Frequency from the first column corresponding to the desired actual frequency in columns 6 or 7.
Note the PWM Value for 100% Duty Cycle.
Find the Duty Cycle by taking the PWM Value of Register 4C and computing:
PWM _Value
DutyCycle _(%) =
ì100%
PWM _Value _ for _ 100%
(1)
Example: For a PWM Frequency of 24, a PWM Value at 100% = 48 and PWM Value actual = 28, then the Duty
Cycle is (28/48) × 100% = 58.3%.
LUT FAN CONTROL
The LM96163 fan control uses a temperature to duty cycle look-up table (LUT) that has 12 indexes. High
resolution duty cycle (0.392%) is available when the PWM frequency is set to 22.5 kHz. In addition ramp rate
control is available to acoustically smooth the duty cycle transition between LUT steps.
Shown in Figure 14 (a) is an example of the 12-point LUT temperature to PWM transfer function that can be
realized without smoothing enabled. The table is comprised of twelve Duty-Cycle and Temperature set-point
pairs. Notice that the transitions between one index of the LUT to the next happen instantaneously. If the PWM
levels are set far enough apart this can be acoustically very disturbing. The typical acoustical threshold of change
in duty cycle is 2%. Figure 14 (b) has an overlaid curve (solid line) showing what occurs at the transitions when
smoothing is enabled. The dashed lines shown in Figure 14 (b) are there to point out that multiple slopes can be
realized easily. At the transitions the duty cycle increments in LSb (0.39% for the case shown) steps. In the
example shown in Figure 14 (b) the first pair is set for a duty-cycle of 31.25% and a temperature of 0°C. For
temperatures less than 0°C the duty cycle is set to 0. When the temperature is greater than 0 °C but is less than
91 °C the duty cycle will remain at 31.25%. The next pair is set at 37.5% and 91°C. Once the temperature
exceeds 91°C the duty cycle on the PWM output will gradually transition from 31.25% to 37.5% in 0.39% steps at
the programmed time interval. The LUT comparison temperature resolution is programmable to either 1 °C or 0.5
°C. For the curves of Figure 14 the comparison resolution is set to 0.5 °C that is why the actual duty cycle
transitions happen 0.5 °C higher than the actual LUT entry. The duty cycle transition time interval is
programmable and is shown in the table titled Table 8. Care should be taken so that the LUT PWM and
Temperature values are setup in ascending weight.
36
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
(a) Without smoothing
(b) With smoothing
Multiple slopes
easily realizable
with 12-point LUT
12-point LUT
Entry
100
93.75
87.5
81.25
75
100
93.75
87.5
81.25
75
68.75
62.5
56.25
50
43.75
37.5
31.25
25
68.75
62.5
56.25
50
43.75
37.5
31.25
25
Ramp rate control
between transitions
has 0.39% step size
PWM Output
Transition
18.75
12.5
6.25
0
18.75
12.5
6.25
0
85
90
95
100
105
110
85
90
95
100
105
110
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 14. Fan Control Transfer Function Example
Also included is programmable hysteresis that is not described by the curves of Figure 14. The hysteresis takes
effect as temperature is decreasing and moves all the temperature set-points down by the programmed amount.
For the example shown here if the hysteresis is set to 1°C and if the temperature is decreasing from 96.5°C the
duty cycle will remain at 68.75% and will not transition to 62.5% until the temperature drops below 95.5°C.
If at any time the TCRIT output were to activate the PWM duty cycle will be instantaneously forced to 100% thus
forcing the fans to full on.
Table 8. PWM Smoothing Time Intervals
Time Interval
(seconds)
0-100% DC Time
w/ 6.25% resolution
(seconds)
w/ 0.39% resolution
Seconds
0.182
0.091
0.046
0.023
2.913
1.456
0.728
0.364
43.7
21.6
10.9
5.45
The Table 8 table describes the programmable time interval preventing abrupt changes in the PWM output duty
cycle and thus preventing abrupt acoustical noise changes as well. The threshold of acoustically detecting fan
noise transition is at about a 2% duty cycle change. The table describes the time intervals that can be
programmed and the total amount of time it will take for the PWM output to change from 0% to 100% for each
time interval. For example if the time interval for each step is set to 0.091 seconds the time it will take to make a
0 to 100% duty cycle change will be 21.6 seconds when the duty cycle resolution is set to 0.39% or 1.46
seconds when the resolution is 6.25%. One setting will apply to all LUT transitions.
COMPUTING RPM OF THE FAN FROM THE TACH COUNT
The Tach Count Registers 46HEX and 47HEX count the number of periods of the 90 kHz tachometer clock in the
LM96163 for the tachometer input from the fan assuming a 2 pulse per revolution fan tachometer, such as the
fans supplied with the Intel boxed processors. The RPM of the fan can be computed from the Tach Count
Registers 46HEX and 47HEX. This can best be shown through an example.
Example:
Given: the fan used has a tachometer output with 2 per revolution.
Let:
Register 46 (LSB) is BFHEX = Decimal (11 x 16) + 15 = 191 and
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
37
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Register 47 (MSB) is 7HEX = Decimal (7 x 256) = 1792.
The total Tach Count, in decimal, is 191 + 1792 = 1983.
The RPM is computed using the formula
f ì 5,400,000
Fan _ RPM =
,
Total _ Tach _ Count _( Decimal )
(2)
where
f = 1 for 2 pulses/rev fan tachometer output;
f = 2 for 1 pulse/rev fan tachometer output, and
f = 2 / 3 for 3 pulses/rev fan tachometer output
For our example
1ì 5,400,000
Fan _ RPM =
= 2723 _ RPM
1983
(3)
DIODE NON-IDEALITY
The LM96163 can be applied easily in the same way as other integrated-circuit temperature sensors, and its
remote diode sensing capability allows it to be used in new ways as well. It can be soldered to a printed circuit
board, and because the path of best thermal conductivity is between the die and the pins, its temperature will
effectively be that of the printed circuit board lands and traces soldered to the LM96163's pins. This presumes
that the ambient air temperature is almost the same as the surface temperature of the printed circuit board; if the
air temperature is much higher or lower than the surface temperature, the actual temperature of the LM96163 die
will be at an intermediate temperature between the surface and air temperatures. Again, the primary thermal
conduction path is through the leads, so the circuit board temperature will contribute to the die temperature much
more strongly than will the air temperature.
The LM96163 incorporates remote diode temperature sensing technology allowing the measurement of remote
temperatures. This diode can be located on the die of a target IC, allowing measurement of the IC's temperature,
independent of the LM96163's die temperature. A discrete diode can also be used to sense the temperature of
external objects or ambient air. Remember that a discrete diode's temperature will be affected, and often
dominated, by the temperature of its leads. Most silicon diodes do not lend themselves well to this application. It
is recommended that an MMBT3904 transistor base emitter junction be used with the collector tied to the base.
The LM96163’s TruTherm BJT beta compensation technology allows accurate sensing of integrated thermal
diodes, such as those found on most processors. With TruTherm technology turned off, the LM96163 can
measure a diode-connected transistor such as the MMBT3904 or the thermal diode found in an AMD processor.
The LM96163 has been optimized to measure the remote thermal diode integrated in a typical Intel processor on
45nm, 65 nm or 90 nm process or an MMBT3904 transistor. Using the Remote Diode TruTherm Enable register
the remote input can be optimized for a typical Intel processor on 45nm, 65 nm or 90 nm process or an
MMBT3904.
Diode Non-Ideality Factor Effect on Accuracy
When a transistor is connected as a diode, the following relationship holds for variables VBE, T and IF:
V
BE
≈
’
◊
ÿ
⁄
»
h x V
…
Ÿ
-1
t
«
e
I = I x
…
Ÿ
F
S
(4)
where:
Vt =
kT
q
(5)
38
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
•
•
•
•
•
•
•
q = 1.6×10−19 Coulombs (the electron charge),
T = Absolute Temperature in Kelvin
k = 1.38×10−23 joules/K (Boltzmann's constant),
η is the non-ideality factor of the process the diode is manufactured on,
IS = Saturation Current and is process dependent,
If = Forward Current through the base-emitter junction
VBE = Base-Emitter Voltage drop
In the active region, the -1 term is negligible and may be eliminated, yielding the following equation
V
BE
≈
’
ÿ
»
h x V
…
Ÿ
◊
t
«
e
I = I x
…
Ÿ
F
S
⁄
(6)
In Equation 6, η and IS are dependant upon the process that was used in the fabrication of the particular diode.
By forcing two currents with a very controlled ratio(IF2 / IF1) and measuring the resulting voltage difference, it is
possible to eliminate the IS term. Solving for the forward voltage difference yields the relationship:
≈IF2’
«IF1◊
≈kT’ x ln
DVBE = h x
q
« ◊
(7)
Solving Equation 7 for temperature yields:
q x DVBE
T =
IF2
≈
’
h x k x ln
∆
∆
÷
÷
IF1
«
◊
(8)
Equation 8 holds true when a diode connected transistor such as the MMBT3904 is used. When this “diode”
equation is applied to an integrated diode such as a processor transistor with its collector tied to GND as shown
in Figure 15 it will yield a wide non-ideality spread. This wide non-ideality spread is not due to true process
variation but due to the fact that Equation 8 is an approximation.
TruTherm BJT beta compensation technology uses the transistor equation, Equation 9, which is a more accurate
representation of the topology of the thermal diode found in an FPGA or processor.
q x DVBE
T =
I
≈
’
C2
h x k x ln∆
÷
÷
∆
IC1
«
◊
(9)
TruTherm should only be enabled when measuring the temperature of a transistor integrated as shown in the
processor of Figure 15, because Equation 9 only applies to this topology.
2
D+
I
E
= I
F
100 pF
3
PROCESSOR
D-
I
R
LM96163
I
C
I
F
2
3
D+
D-
MMBT3904
100 pF
I
R
LM96163
Figure 15. Thermal Diode Current Paths
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
39
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
Calculating Total System Accuracy
The voltage seen by the LM96163 also includes the IFRS voltage drop of the series resistance. The non-ideality
factor, η, is the only other parameter not accounted for and depends on the diode that is used for measurement.
Since ΔVBE is proportional to both η and T, the variations in η cannot be distinguished from variations in
temperature. Since the non-ideality factor is not controlled by the temperature sensor, it will directly add to the
inaccuracy of the sensor. For the for Intel processor on 65nm process, Intel specifies a +4.06%/−0.897%
variation in η from part to part when the processor diode is measured by a circuit that assumes diode equation,
Equation 8, as true. As an example, assume a temperature sensor has an accuracy specification of ±1.0°C at a
temperature of 80°C (353 Kelvin) and the processor diode has a non-ideality variation of +4.06%/−0.89%. The
resulting system accuracy of the processor temperature being sensed will be:
TACC = + 1.0°C + (+4.06% of 353 K) = +15.3 °C
(10)
and
TACC = - 1.0°C + (−0.89% of 353 K) = −4.1 °C
(11)
TruTherm technology uses the transistor equation, Equation 8, resulting in a non-ideality spread that truly reflects
the process variation which is very small. The transistor equation non-ideality spread is ±0.39% for the 65nm
thermal diode. The resulting accuracy when using TruTherm technology improves to:
TACC = ±0.75°C + (±0.39% of 353 K) = ± 2.16 °C
(12)
Intel does not specify the diode model ideality and series resistance of the thermal diodes on 45nm so a similar
comparison cannot be calculated, but lab experiments have shown similar improvement. For the 45nm processor
the ideality spread as specified by Intel is -0.399% to +0.699%. The resulting spread in accuracy when using
TruTherm technology with the thermal diode on Intel processors with 45nm process is:
TACC = -0.75°C + (-0.39% of 353 K) = -2.16 °C
(13)
to
TACC = +0.75°C + (+0.799% of 353 K) = +4.32 °C
(14)
The next error term to be discussed is that due to the series resistance of the thermal diode and printed circuit
board traces. The thermal diode series resistance is specified on most processor data sheets. For Intel
processors in 45 nm process, this is specified at 4.5Ω typical with a minimum of 3Ω and a maximum of 7Ω. The
LM96163 accommodates the typical series resistance of Intel Processor on 45 nm process. The error that is not
accounted for is the spread of the processor's series resistance. The equation used to calculate the temperature
error due to series resistance (TER) for the LM96163 is simply:
º
W
≈
’
÷
C
TER = 0.62
x R
PCB
∆
«
◊
(15)
Solving Equation 15 for RPCB equal to -1.5Ω to 2.5Ω results in the additional error due to the spread in this series
resistance of -0.93°C to +1.55°C. The spread in error cannot be canceled out, as it would require measuring
each individual thermal diode device. This is quite difficult and impractical in a large volume production
environment.
Equation 15 can also be used to calculate the additional error caused by series resistance on the printed circuit
board. Since the variation of the PCB series resistance is minimal, the bulk of the error term is always positive
and can simply be cancelled out by subtracting it from the output readings of the LM96163 using the Remote
Temperature Offset register.
Transistor Equation ηT, non-ideality
Series R,Ω
Processor Family
min
typ
max
1.008
1.005
Intel Processor on 45 nm process
Intel Processor on 65 nm process
0.997
0.997
1.001
1.001
4.5
4.52
40
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
LM96163
www.ti.com
SNAS433D –JUNE 2008–REVISED MAY 2013
PCB LAYOUT FOR MINIMIZING NOISE
Figure 16. Ideal Diode Trace Layout
In a noisy environment, such as a processor mother board, layout considerations are very critical. Noise induced
on traces running between the remote temperature diode sensor and the LM96163 can cause temperature
conversion errors. Keep in mind that the signal level the LM96163 is trying to measure is in microvolts. The
following guidelines should be followed:
1. Use a low-noise +3.3VDC power supply, and bypass to GND with a 0.1 µF ceramic capacitor in parallel with
a 100 pF ceramic capacitor. The 100 pF capacitor should be placed as close as possible to the power supply
pin. A bulk capacitance of 10 µF needs to be in the vicinity of the LM96163's VDD pin.
2. A 100 pF diode bypass capacitor is recommended to filter high frequency noise but may not be necessary.
Place the recommended 100 pF diode capacitor as close as possible to the LM96163's D+ and D− pins.
Make sure the traces to the 100 pF capacitor are matched. The LM96163 can handle capacitance up to 3 nF
placed between the D+ and D- pins, see Typical Performance Characteristics curves titled Remote
Temperature Reading Sensitivity to Thermal Diode Filter Capacitance.
3. Ideally, the LM96163 should be placed within 10 cm of the Processor diode pins with the traces being as
straight, short and identical as possible. Trace resistance of 1 Ω can cause as much as 0.62°C of error. This
error can be compensated by using the Remote Temperature Offset Registers, since the value placed in
these registers will automatically be subtracted from or added to the remote temperature reading.
4. Diode traces should be surrounded by a GND guard ring to either side, above and below if possible. This
GND guard should not be between the D+ and D− lines. In the event that noise does couple to the diode
lines it would be ideal if it is coupled common mode. That is equally to the D+ and D− lines.
5. Avoid routing diode traces in close proximity to power supply switching or filtering inductors.
6. Avoid running diode traces close to or parallel to high speed digital and bus lines. Diode traces should be
kept at least 2 cm apart from the high speed digital traces.
7. If it is necessary to cross high speed digital traces, the diode traces and the high speed digital traces should
cross at a 90 degree angle.
8. The ideal place to connect the LM96163's GND pin is as close as possible to the Processor's GND
associated with the sense diode.
9. Leakage current between D+ and GND should be kept to a minimum. Thirteen nano-amperes of leakage can
cause as much as 0.2°C of error in the diode temperature reading. Keeping the printed circuit board as clean
as possible will minimize leakage current.
Noise coupling into the digital lines greater than 400 mVp-p (typical hysteresis) and undershoot less than 500 mV
below GND, may prevent successful SMBus communication with the LM96163. SMBus no acknowledge is the
most common symptom, causing unnecessary traffic on the bus. Although the SMBus maximum frequency of
communication is rather low (100 kHz max), care still needs to be taken to ensure proper termination within a
system with multiple parts on the bus and long printed circuit board traces. An RC lowpass filter with a 3 dB
corner frequency of about 40 MHz is included on the LM96163's SMBCLK input. Additional resistance can be
added in series with the SMBDAT and SMBCLK lines to further help filter noise and ringing. Minimize noise
coupling by keeping digital traces out of switching power supply areas as well as ensuring that digital lines
containing high speed data communications cross at right angles to the SMBDAT and SMBCLK lines.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
41
Product Folder Links: LM96163
LM96163
SNAS433D –JUNE 2008–REVISED MAY 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (May 2013) to Revision D
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 41
42
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM96163
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LM96163CISD/NOPB
LM96163CISDX/NOPB
ACTIVE
ACTIVE
WSON
WSON
DSC
DSC
10
10
1000 RoHS & Green
4500 RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
T63C
T63C
SN
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM96163CISD/NOPB
LM96163CISDX/NOPB
WSON
WSON
DSC
DSC
10
10
1000
4500
178.0
330.0
12.4
12.4
3.3
3.3
3.3
3.3
1.0
1.0
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LM96163CISD/NOPB
LM96163CISDX/NOPB
WSON
WSON
DSC
DSC
10
10
1000
4500
208.0
367.0
191.0
367.0
35.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明