LMH6525 [TI]
具有双输出的四通道激光二极管驱动器;
| 型号： | LMH6525 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 具有双输出的四通道激光二极管驱动器 驱动 二极管 激光二极管 驱动器 |
| 文件： | 总25页 (文件大小：1278K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
LMH6525/LMH6526 Four–Channel Laser Diode Driver with Dual Output
Check for Samples: LMH6525, LMH6526
1
FEATURES
•
•
LMH6525 has Differential Enable Oscillator
Inputs
23
•
Fast Switching: Rise and Fall Times: 0.6/1.0
ns.
LMH6526 has Single Ended Enable Oscillator
Inputs
•
Low Voltage Differential Signaling (LVDS)
Channels Enable Interface for the Fast
Switching Lines
APPLICATIONS
•
Combination DVD/CD Recordable and
Rewritable Drives
•
•
Low Output Current Noise: 0.24 nA/√Hz
Dual Output: Selectable by SELA/B Pin (Active
HIGH)
•
•
DVD Camcorders
DVD Recorders
–
SELA = LMH6526 SEB = LMH6525
•
Four Independent Current Channels
DESCRIPTION
–
–
Gain of 300, 300 mA Write Channel
The LMH™6525/6526 is a laser diode driver for use
in combination DVD/CD recordable and rewritable
systems. The part contains two high-current outputs
for reading and writing the DVD (650 nm) and CD
(780 nm) lasers. Functionality includes read, write
and erase through four separate switched current
channels. The channel currents are summed together
at the selected output to generate multilevel
waveforms for reading, writing and erasing of optical
discs. The LVDS interface delivers DVD write speeds
of 16x and higher while minimizing noise and
crosstalk. The LMH6525/6526 is optimized for both
speed and power consumption to meet the demands
of next generation systems. The part features a 150
mA read channel plus one 300 mA and two 150 mA
write channels, which can be summed to allow a total
output current of 600 mA or greater. The channel
currents are set through four independent current
inputs.
Gain of 150, 150 mA Low-Noise Read
Channel
–
–
Two Gain of 150, 150 mA Write Channels
600 mA Minimum Combined Output Current
•
Integrated AC Coupled HFM Oscillator
–
Selectable Frequency and Amplitude
Setting
–
–
–
By External Resistors
200 MHz to 600 MHz Frequency Range
Amplitude to 100 mA Peak-to-Peak
Modulation
•
•
•
•
Complete Shutdown by ENABLE Pin
5V Single-Supply Operation
Logic inputs TTL and CMOS compatible
Space Saving Package (OFN)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
LMH is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2013, Texas Instruments Incorporated
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
Block Diagrams
I4
EN4
EN4B
I4
EN4
EN4B
LMH6526
CHANNEL 4
CHANNEL 4
LMH6525
I3
EN3
I3
EN3
CHANNEL 3
CHANNEL 2
CHANNEL 3
CHANNEL 2
EN3B
EN3B
OUTPUT A
OUTPUT A
OUTPUT B
IOUTA
IOUTB
IOUTA
IOUTB
I2
EN2
EN2B
I2
EN2
EN2B
OUTPUT B
I
R
I
R
READ CHANNEL
RF OSCILLATOR
READ CHANNEL
RF OSCILLATOR
ENR
ENR
V
V
DD
DD
ENOSC
V
V
V
V
DD
DD
ENOSC
ENOSCB
DD
DD
V
DD
A
V
DD
A
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION (CONTINUED)
An on-board High-Frequency Modulator (HFM) oscillator helps reduce low-frequency noise of the laser and is
enabled by applying LVDS levels on the ENOSC pins for the LMH6525, while the LMH6526 is enabled by
applying an asymmetrical signal on the ENOSC pin. The fully differential oscillator circuit minimizes supply line
noise, easing FCC approval of the overall system. The SELA/B pin (active HIGH) selects the output channel and
oscillator settings. External resistors determine oscillator frequency and amplitude for each setting. The write and
erase channels can be switched on and off through dedicated LVDS interface pins.
(1)(2)
Absolute Maximum Ratings
(3)
ESD Tolerance
Human Body Model
2 KV
200V
(4)
Machine Model
Supply Voltages V+ – V−
5.5V
Differential Input Voltage
±5.5V
(5)
Output Short Circuit to Ground
Input Common Mode Voltage
Storage Temperature Range
Continuous
V− to V+
−65°C to +150°C
+150°C
(6)
Junction Temperature
(1) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For specifications, see the Electrical
Characteristics tables.
(3) For testing purposes, ESD was applied using "Human Body Model”; 1.5 kΩ in series with 100 pF.
(4) Machine Model, 0Ω in series with 200 pF.
(5) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 150°C.
(6) The maximum power dissipation is a function of TJ(MAX), θJA and TA. The maximum allowable power dissipation at any ambient
temperature is PD= (TJ(MAX) — TA)/ θJA. All numbers apply for packages soldered directly onto a PC board..
Operating Ratings
Supply Voltage (V+ – V−)
4.5V ≤ VS ≤ 5.5V
−40°C ≤ TA ≤ 85°C
QFN Package
(1)
Operating Temperature Range (TA)
(2) (1)
Package Thermal Resistance
,
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. Parametric performance is as indicated in the electrical tables under conditions of
internal self-heating where TJ > TA. See Applications section for information on temperature de-rating of this device.
(2) The maximum power dissipation is a function of TJ(MAX), θJA and TA. The maximum allowable power dissipation at any ambient
temperature is PD= (TJ(MAX) — TA)/ θJA. All numbers apply for packages soldered directly onto a PC board..
2
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
Operating Ratings (continued)
(θJC
)
3°C/W
42°C/W
(θJA) (no heatsink)
(3)
(θJA) (no heatsink see
)
30.8°C/W
IINR/3/4
IIN2
1.5 mA (Max)
1.0 mA (Max)
1000 Ω (Min)
1000 Ω (Min)
100-600 MHz
10-100 mAPP
RFREQ
RAMP
FOSC
AOSC
(3) This figure is taken from a thermal modeling result. The test board is a 4 layer FR-4 board measuring 101 mm x 101 mm x 1.6 mm with
a 3 x 3 array of thermal vias. The ground plane on the board is 50 mm x 50 mm. Ambient temperature in simulation is 22°C, still air.
Power dissipation is 1W.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
(1)
+5V DC Electrical Characteristics
Unless otherwise specified, all limits specified for TJ = 25°C, RL = 10Ω. Boldface limits apply at the temperature extremes.
(2)
(3)
(2)
Symbol
LVDS
Parameter
Conditions
Min
Typ
Max
Units
(4)
VI
Input Voltage Range
|VGPD| < 50 mV
0
1.7
2.4
V
(4)
VIDTH
VHYST
RIN
Input Diff. Threshold
Input Diff. Hysteresis
Input Diff. Impedance
Input Current
|VGPD| < 50 mV
VIDTHH – VIDTHL
–100
25
0
0
100
mV
mV
Ω
95
115
8
135
20
IIN
Excluding RIN Current , VCM = 1.25V
RIN to Ground
μA
Current Channels
RIN
Input Resistance all Channels
475
580
2.1
675
16
Ω
IOS2
Current Offset Channel 2
Channel R,3,4 Off
IIN = 0, EN = High
mA
IOS,R,3,4
Current Offset Channel R,3,4
All Channels Off
IIN = 0, EN = High
1.2
9
mA
AIW
Current Gain
Channel 2
345
135
160
386
159
182
1.7
430
180
200
3
A/A
A/A
A/A
%
AIR
Current Gain
Channel Read
Channel 3 and 4
AI,3,4
ILIN-R,2,3,4
Current Gain
Output Current Linearity
200 μA < IIN < 1000 μA; RLOAD = 5Ω
Channels Read, 2,3 and 4
IOUTW
IOUTR
Output Current
Output Current
Channel 2 @ 1 mA input current
285
140
300
162
mA
mA
Channel Read
@ 1 mA input current
IOUT3,4
Output Current
Channel 3 and 4
@ 1 mA input current
160
600
183
mA
(5)
IOUTTOTAL Total Output Current
All Channels
mA
V
VTLO
TTL Low Voltage
Input (H to L), ENR
ENOSC (LMH6526)
1.29
1.40
0.8
0.8
VTLO
TTL Low Voltage
Input (H to L)
V
B-Select (LMH6525)
A-Select (LMH6526)
VELO
VTHI
Enable Low Voltage
TTL High Voltage
Enable Input (H to L)
1.98
1.27
0.8
V
V
Input (L to H), ENR
ENOSC (LMH6526)
2
2
VTHI
TTL High Voltage
Input (L to H)
1.51
V
B-Select (LMH6525)
A-Select (LMH6526)
VEHI
ISpd
ISr1
Enable High Voltage
Enable Input (L to H)
Enable = Low
2.8
2.13
0.003
81.5
V
Supply Current, Power Down
0.1
mA
mA
Supply Current, Read Mode,
Oscillator Disabled
ENOSC = Low; ENOSCB = High
I2 = I3 = I4 = IR = 125 μA
100
ISr2
Supply Current, Read Mode,
Oscillator Enabled
ENOSC = High; ENOSCB = Low
I2 = I3 = I4 = IR = 125 μA
RFA = 3.5 kΩ
81.5
100
mA
ISwr
IS
Supply Current, Write Mode
Supply Current
EN2 = EN3 = EN4 = High;
I2 = I3 = I4 = IR = 125 μA
180
33
210
40
mA
mA
All Channels disable, no input current.
SELA/B = Low
RAA, RAB, RFA, RFB = ∞
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. Parametric performance is as indicated in the electrical tables under conditions of
internal self-heating where TJ > TA. See Applications section for information on temperature de-rating of this device.
(2) All limits are specified by testing or statistical analysis.
(3) Typical values represent the most likely parametric norm.
(4) VGPD = ground potential difference voltage between driver and receiver
(5) Total input current is 4 mA (all 4 channels equal) and output currents are summed together (see typical performance characteristics).
4
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
+5V AC ELECTRICAL CHARACTERISTICS
Unless otherwise specified, all limits specified for TJ = 25°C, IOUT = 40 mA DC and 40 mA pulse, RL = 50Ω. Boldface limits
apply at the temperature extremes.
(1)
(2)
(1)
Symbol
Parameter
Write Rise Time
Conditions
Min
Typ
0.6
Max
Units
tr
tf
tr
tf
tr
tf
IOUT = 40 mA (Read) + 40 mA
(10% to 90%) RLOAD = 5Ω
ns
Write Fall Time
IOUT = 40 mA (Read) + 40 mA
(90% to 10%) RLOAD = 5Ω
1.6
0.6
1.0
0.6
1.0
18
ns
ns
Write Rise Time
IOUT = 100 mA (Read) + 100 mA
(10% to 90%) RLOAD = 5Ω
Write Fall Time
IOUT = 100 mA (Read) + 100 mA
(90% to 10%) RLOAD = 5Ω
ns
Write Rise Time
IOUT = 150 mA (Read) + 150 mA
(10% to 90%) RLOAD = 5Ω
ns
Write Fall Time
IOUT = 150 mA (Read) + 150 mA
(90% to 10%) RLOAD = 5Ω
ns
OS
IN0
Output Current Overshoot
Output Current Noise
IOUT = 40 mA (Read) + 40 mA
%
(3)
IOUT = 40 mA; RLOAD = 50Ω;
0.24
nA/√Hz
f = 50 MHz; ENOSC = Low
tON
IOUT ON Prod. Delay
Switched on EN2 and EN2B
Switched on EN2 and EN2B
Switched on ENR
3.1
3.3
3.5
2.8
37
ns
ns
tOFF
tdisr
Tenr
tdis
IOUT OFF Prop. Delay
Disable Time, Read Channel
Enable Time, Read Channel
Disable Time (Shutdown)
Enable Time (Shutdown)
Channel Bandwidth, −3 dB
Oscillator Frequency
as
Switched on ENR
ns
Enable = High to Low
Enable = Low to High
IOUT = 50 mA, All Channels
ns
ten
4.5
250
360
µs
BWC
FOSC
KHz
MHz
RF = 3.48 kΩ
290
430
Range 200 MHz to 600 MHz
TDO
TEO
TDO
TEO
Disable Time Oscillator
Enable Time Oscillator
Disable Time Oscillator
Enable Time Oscillator
LMH6525
LMH6525
LMH6526
LMH6526
5
4
7
4
ns
ns
ns
ns
(1) All limits are specified by testing or statistical analysis.
(2) Typical values represent the most likely parametric norm.
(3) This is the average between the positive and negative overshoot.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
CONNECTION DIAGRAMS
28-Pin (QFN)
Top View
28-Pin (QFN)
Top View
4
3
1
7
6
5
2
I
8
9
GNDB
28
27
R
7
6
5
4
3
2
1
IOUTB
I
GNDB
I2
8
9
28
27
R
V
DD
IOUTB
I3 10
26
25
I2
V
DD
DD
11
I4
LMH6525
V
26
25
10
11
DD
I3
I4
V
V
DD
R
LMH6526
12
24
23
22
FA
R
R
NC
FB 13
V
24
23
22
R
R
12
DD
FA
AA 14
EN4
NC
FB 13
14
EN4
21
R
15 16
17
18
19 20
AA
20 21
15 16 17 18 19
See Package Number NJD0028A
See Package Number NJD0028A
Table 1. Pin Description
Pin #
Description
Laser driver output channel A
LVDS Oscillator Enable pin
Remarks
1.
2.
3.
4.
5.
6.
7.
8.
9.
Internal Oscillator activated if logical input is high
Internal Oscillator activated if logical input is low
Read Channel active if pin is high
LVDS Oscillator Enable pin B (only LMH6525)
Read Channel Enable pin
Chip Enable pin
Chip Enabled if pin is high
Supply Voltage A
Ground Connection A
Read Channel current setting
Channel 2 current setting
1 mA input current result in 150 mA output current
1 mA input current result in 300 mA output current
1 mA input current result in 150 mA output current
1 mA input current result in 150 mA output current
Set by external resistor to ground
10.
11.
12.
13.
14.
15.
16.
Channel 3 current setting
Channel 4 current setting
Oscillator Frequency setting Channel A
Oscillator Frequency setting Channel B
Oscillator Amplitude setting Channel A
Oscillator Amplitude setting Channel B
Set by external resistor to ground
Set by external resistor to ground
Set by external resistor to ground
Channel select B (LMH6525)
Channel select A (LMH6526)
Channel selected if pin is high
17.
18.
19.
20.
21.
22.
23.
24.
25.
LVDS input Channel 2B
LVDS input Channel 2
LVDS input Channel 3B
LVDS input Channel 3
LVDS input Channel 4B
LVDS input Channel 4
NC
Channel 2 active if logical input is low
Channel 2 active if logical input is high
Channel 3 active if logical input is low
Channel 3 active if logical input is high
Channel 4 active if logical input is low
Channel 4 active if logical input is high
Supply Voltage
Supply Voltage
6
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
Table 1. Pin Description (continued)
Pin #
26.
Description
Remarks
Supply Voltage
27.
Laser driver output channel B
Ground Connection B
28.
Truth Tables
Table 2. IOUT Control
ENABLE
ENR
EN2
X
EN3
X
EN4
X
IOUT
OFF
0
1
1
1
1
1
X
0
1
1
1
1
0
0
0
OFF
0
0
0
AR * IINR
1
0
0
AR * IINR + A2 * IIN2
AR * IINR + A3 * IIN3
AR * IINR + A4 * IIN4
0
1
0
0
0
1
Table 3. Oscillator Control
ENABLE
ENOSC
ENR
X
EN2
X
EN3
X
EN 4
OSCILLATOR
0
1
1
X
0
1
X
X
X
OFF
OFF
ON
X
X
X
X
X
X
NOTE
Note: EN2, EN3, EN4 AND ENOSC are LVDS SIGNALS USING THE LMH6525.
EN2, EN3 and EN4 are LVDS signals using the LMH6526.
Waveforms
ENABLE
ENR
ON
EN2B
EN2
ON
ON
ON
ON
EN3B
EN3
ON
EN4B
EN4
ON
AMPLITUDE
AMPLITUDE
SET BY I2
AMPLITUDE
SET BY I3
AMPLITUDE
SET BY I4
SET BY I
R
IOUTA
SUMMATION OF
I2, I3 and I4
Figure 1. Functional Timing Diagram
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
ENABLE
ENR
IOUTA
t
dis
t
en
Figure 2. Enable Timing
ENABLE
ENR
IOUTA
t
t
disr
enr
Figure 3. Read Timing
ENABLE
EN2B,3B,4B
EN2,3,4
t
t
OFF
ON
IOUTA
t
r
t
f
Figure 4. Write Timing
ENABLE
ENR
ENOSC
IOUTA
T
T
DO
EO
Figure 5. Oscillator Timing
8
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
Detailed Block Diagram
EN4
CLOSED IF HIGH
+
-
100W
EN4B
I4
+
-
500W
100W
EN3
CLOSED IF HIGH
+
-
EN3B
I3
+
-
500W
100W
EN2
CLOSED IF HIGH
+
-
EN2B
I2
IOUTA
+
-
IOUTB
500W
CLOSED IF HIGH
ENR
I
R
+
-
500W
CLOSED IF HIGH
ENOSC
ENOSCB
NC at LMH6526
OSC
CONTROL
SHUTDOWN
CONTROL
SELB (LMH6525)
SELA (LMH6526)
ENABLE
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
Application Schematic
DIGITAL SYSTEM DACs
DAC
BETWEEN
PINS 6
BETWEEN
PINS 26
AND 28
5V
5V
AND 7
DAC
DAC
100 nF
47 mF
68 nF
47 mF
DAC
3k 3k
3k
3k
LMH6525
LMH6526
8
DIGITAL DRIVER
I
R
DIGITAL SYSTEM
LOGIC
4
9
ENR
ENR
1
IOUTA
18
17
EN2
EN2
EN2B
LASER
DIODE
EN2B
10
20
19
EN3
EN3
EN3B
EN3B
11
27
IOUTB
22
21
EN4
EN4
EN4B
EN4B
LASER
DIODE
LVDS
DRIVERS
OSCILLATOR
12
13
R
FA
FB
AA
R
R
14
15
R
AB
DIGITAL LOGIC
23
NC
2
3
ENOSC
ENOSCB
SELB
ENOSC
NA for LMH6526
ENOSCB
SELB
SELA for LMH6526
16
5
ENABLE
ENABLE
GNDA AND V A ARE ANALOG
DD
SIGNAL GROUND AND POWER.
THEY ARE NOT CONNECTED TO
GNDB AND V
INSIDE THE CHIP
DD
FREQUENCY
A
FREQUENCY
B
AMPLITUDE
B
AMPLITUDE
A
LOWER RESISTANCE = HIGHER FREQUENCY AND AMPLITUDE
10
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
Typical Performance Characteristics
(TJ = 25°C, V+ = ±5V, V− = 0V; Unless Specified).
Oscillator Amplitude
Oscillator Amplitude
vs.
RA
vs.
RA
140
140
120
100
80
V
I
= 5V
S
= 150 mA
DC
120
100
R
= 10W
LOAD
f = 300 MHz
V
I
= 5V
S
V
S
= 5V
= 150 mA
DC
80
60
40
20
0
I
= 150 mA
DC
R
= 10W
LOAD
V
= 5V
S
60
R
= 5W
f = 300 MHz
LOAD
f = 300 MHz
I
= 150 mA
DC
R
= 5W
LOAD
40
20
0
f = 300 MHz
0
1
2
3
4
5
6
7
8
9
10
0
10 20 30 40 50 60 70 80
(kW)
R
RA (kW)
A
Figure 6.
Figure 7.
Oscillator Frequency
vs.
RF
Pulse Response
600
0.5
0.4
0.3
V
= 5V
S
R
= 5W
LOAD
500
400
300
200
100
0
0.2
0.1
V
= 5V
S
R
= 5W
LOAD
STEP
V
V
= 40 mA
= 40 mA
DC
0
0
10 20 30 40 50 60 70 80
TIME (ns)
0
1
2
3
4
5
6
7
8
9
R
(kW)
F
Figure 8.
Figure 9.
Noise
vs.
Frequency
Headroom & Output Current
vs.
Total Input Current
4
3.5
3
900
800
700
2.7
V
= 5.5V
R
= 25W
S
LOAD
2.4
2.1
OSC = OFF
= 40 mA
I
DC
600
500
1.8
1.5
HEADROOM
2.5
2
V
= 5.0V
S
400
300
1.2
0.9
1.5
1
V
= 4.5V
S
200
100
0
0.6
0.3
0
OUTPUT CURRENT
0.5
0
R
= 5W
L
1
10
20 30 4050
0
1
2
3
4
5
6
7
8
FREQUENCY (MHz)
TOTAL INPUT CURRENT (mA)
Figure 10.
Figure 11.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
APPLICATION INFORMATION
CIRCUIT DESCRIPTION
General & Spec
The LMH6525/6526 is a 4-channel-input, dual-output laser driver. The dual outputs are meant to drive two
different laser diodes, one for CD reading and writing and one for DVD reading and writing. The part has an
oscillator that can be set for both amplitude and frequency. The oscillator has four input pins for setting both the
amplitude and frequency by connecting external resistors to ground. The part operates at 5V and is capable to
deliver a minimum total output current of 500 mA.
INPUTS
Current-Setting Inputs
The 4 input channels are transconductance-type inputs. This means the output current of the channel is
proportional to the current (not voltage) sourced into the input pin. That is why these pins are designated by the
letter “I” to indicate the current input nature of the pin. The read channel current-setting pin is “IR”, the Channel 2
current-setting pin is “I2” and so on. Using a transconductance-type input eliminates the high-impedance inputs
associated with a voltage input amplifier. The lower input impedances of the input nodes lowers the susceptibility
of the part to EMI/RFI. The Read Channel (IR) and Channel 3 (I3) and 4 (I4) current-setting inputs have a gain of
150. The Channel 2 input (I2) has a current gain of 300. Sourcing one milliampere into the pins IR, I3 or I4, will
result in 150 mA at the output for each Channel, while 1 mA into I2 will result in 300 mA at the output for Channel
2. These currents of 150 mA and 300 mA are the maximum allowable currents per channel. The total allowable
output current from all the channels operating together exceeds 500 mA.
Channel Enable Inputs
Each of the four channels has one (read) or two enable inputs that allow the channel to be turned on or off. The
read channel enable (ENR) is a single-ended TTL/CMOS compatible input. A single-ended signal is adequate for
this channel because the read channel is generally enabled the entire time the drive is reading or writing. The
three write/erase channels need to be operated much faster so these channel enables are LVDS (Low Voltage
Differential Signal) inputs. Each channel has two inputs, such as EN2 and EN2B. Following the standard an
LVDS output consists of a current source of 3.5 mA, and this current produces across the internal termination
resistor of 100Ω in the LMH6525 or LMH6526 a voltage of 350 mV. The polarity of the current through the
resistor can change very quickly thus switching the channel current on or off. The bias level of the LVDS signal is
about 1.2V, so the operating levels are 175 mV above and below this bias level. The ENxB inputs act as the not
input so if the other input is at logical ‘1’ state and the not input at ‘0’ state the channel is activated. The internal
100Ω resister provides a proper termination for the LVDS signals, saving space and simplifying layout and
assembly.
Control Inputs
There are two other control inputs (next to the oscillator enable which is covered in the next section). There are
the global chip Enable and output select pin SELA or SELB. Setting the Enable pin to a level above 2V will
enable the part. This means the supply current raises from sleep mode value to the normal operating values. The
SELA or SELB input (TTL/ CMOS levels) controls which output is active. When at logical ‘1’ state the output
indicated by it’s name is active. The mode of this pin also controls the oscillator circuitry which means that the
appropriate setting resistors become active as described in the next section.
Oscillator Inputs
The oscillator section can be switched on or off by a LVDS signal for the LMH6525 and by a TTL/ CMOS signal
for the LMH6526. When switched on the oscillator will modulate the output current. The settings of the frequency
and amplitude are done by 4 resistors, two for every channel. RFA and RFB pins set the oscillator frequency for
the A and B outputs respectively. The RAA and RAB pins set the oscillator amplitude for the A and B channels
respectively. These 4 inputs work by having current drawn out of the pin by a setting resistor or potentiometer.
The frequency and amplitude increase by decreasing setting resistor value. There are two charts in the Typical
Performance Characteristics section that relates the setting resistor value to the resulting frequency or amplitude.
Normally the settings for the frequency and amplitude are done by connecting the pin via a resistor to ground. If
needed to program this settings it is possible to connect these RFx and RAx pins via a current limiting resistor to
12
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
the output of an op amp or DAC. When using such a circuitry the output can be held at a negative voltage, which
means even if the channel pins RFx and RAx are not selected, current is drawn from the pin. This is only true
when the negative voltage has such a value that the internal transistors connected to the pin will conduct. This
will influence the settings of the active pins RFx and RAx. Due to this effect it is recommended, when using a
negative voltage lower as -0.5V, to disable this voltage simultaneously with the channel.
OUTPUT
The outputs can source currents in excess of 600 mA. The output pins have been designed to have minimal
series inductance in order to minimize current overshoot on fast pulses. The outputs have a saturation voltage of
about 1V. The table below shows the typical output saturation Voltages into a 5Ω load at various supply voltages.
Table 4. Output Saturation
Supply Voltage (V)
Maximum Output (mA) 5Ω
Saturation Voltage (V)
4.5V
5.0V
5.5V
700
777
846
0.8
0.89
1.02
As can be seen, even with a 4.5V supply voltage the part can deliver 700 mA while the saturation voltage is at
0.8V. This means the output voltage of the part can be at maximum 700e-3*5 = 3.5V. With a saturated output
voltage (see Figure 12) of 0.8V the voltage on the supply pin of the part is 4.3V. The used supply voltage is 4.5V
so there is a supply voltage loss of 0.2V over the supply line resistance, but nevertheless the part can drive laser
diodes with a forward voltage up to 3.5V with currents over 500 mA. When operating at 5.5V the part can deliver
currents over 800 mA. In this case the output at the anode of the laser diode is 846e-3*5 = 4.23V, combined with
the saturated output voltage of 1.02V the supply voltage of the part at the power pin is 5.25V and this means the
supply line loss is 0.25V. So at 5.5V supply voltage the part can drive laser diodes with a forward voltage in
access of 4V.
V
SUPPLY
SUPPLY LINE
RESISTANCE
SATURATED
OUTPUT
VOLTAGE
OUTPUT STAGE
LMH65xx
LASER
DIODE
Figure 12. Output Configuration
Application Hints
SUPPLY SEQUENCING
As the LMH6525/6526 is fabricated in the CMOS7 process, latch-up concerns are minimal. Be aware that
applying a low impedance input to the part when it has no supply voltage will forward bias the ESD diode on the
input pin and then source power into the part’s VDD pin. If the potential exists for sustained operation with active
inputs and no supply voltage, all the active inputs should have series resistors to limit the current into the input
pins to levels below a few milliamperes.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
DECOUPLING
The LMH6525/6526 has very high output currents changing within a nanosecond. This makes decoupling
especially important. High performance, low impedance ceramic capacitors should be located as close as
possible to the supply pins. The LMH6525/6526 needs two decoupling capacitors, one for the analog power and
ground VDDA, GNDA) and one for the power side supply and ground (3xVDD and GNDB). The high level of output
current dictates the power side decoupling capacitor should be 0.1 microfarads minimum. Larger values may
improve rise times depending on the layout and trace impedances of the connections. The capacitors should
have direct connection across the supply pins on the top layer, preferably with small copper-pour planes. These
planes can connect to the bottom side ground and/or power planes with vias but there should be a topside low
impedance path with no vias if possible. (see also Figure 15 Decoupling Capacitors).
OVERSHOOT
As the LMH6525/6526 has fast rise times of less then a nanosecond, any inductance in the output path will
cause overshoot. This includes the inductance in the laser diode itself as well as any trace inductance. A series
connection of a resistor and a capacitor across the laser diode could be helpful to reduce unwanted overshoot or
to reduce the very high peaks caused by the relaxation oscillations of a laser diode when driven from below the
knee voltage. But keep always in mind that this causes a slower rise and/ or fall time. Typical values are 10Ω
and 100 pF. The actual values required depend on the laser diode used and the circuit layout and should be
determined empirically.
THERMAL
General
The LMH6525/6526 is a very high current output device. This means that the device must have adequate heat-
sinking to prevent the die from reaching its absolute maximum rating of 150°C. The primary way heat is removed
from the LMH6525/6526 is through the Die Attach Pad, the large center pad on the bottomside of the device.
Heat is also carried out of the die through the bond wires to the traces. The outputs and the VDD pads of the
device have double bond wires on this device so they will conduct about twice as much heat to the pad. In any
event, the heat able to be transferred out the bond wires is far less than that which can be conducted out of the
die attach pad. Heat can also be removed from the top of the part but the plastic encapsulation has worse
thermal conductivity then copper. This means a heat sink on top of the part is less effective than the same
copper area on the circuit board that is thermally attached to the Die Attach Pad.
PBC Heatsinks
In order to remove the heat from the die attach pad there must be a good thermal path to large copper pours on
the circuit board. If the part is mounted on a dual-layer board the simplest method is to use 6 or 8 vias under the
die attach pad to connect the pad thermally (as well as electrically, of course) to the bottomside of the circuit
board. The vias can then conduct heat to a copper pour area with a size as large as possible. Please see
application note AN-1187 (Literature Number SNOA401) for guidelines about these vias and QFN packaging in
general.
Derating
It is essential to keep the LMH6525/6526 die under 150°C. This means that if there is inadequate heat sinking
the part may overheat at maximum load while at maximum operating ambient of 85°C. How much power
(current) the part can deliver to the load at elevated ambient temperatures is purely dependent on the amount of
heat sinking the part is provided with.
LAYOUT
Inputs
Critical inputs are the LVDS lines. These are two coupled lines of a certain impedance, mostly 100Ω. For some
reason those lines could have another value but in that case the termination resistance must have the same
value. The differential input resistance of the LMH6525 and LMH6526 is 100Ω and normally the impedance of
the incoming transmission line matches that value. When using a flexible flat cable it is important to know the
impedance of two parallel wires in that cable. Flex cables can have different pitch distances, but a commonly
14
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
used cable has a pitch of 0.5 mm. When verified by TDR equipment, the measurements show an impedance of
about 142Ω. It is possible to calculate the impedance of such a cable when some parameters are known.
Needed parameters are the pitch (a) of the wires, the thickness (d) en r (see Figure 13). When Checked under a
microscope: the thickness of the wires is 0.3 mm. The pitch is 0.5 mm, while the ;r must be 1 for air. The
impedance of two parallel wires is given by this formula,
Z = (276/r) * log{(2*a)/d}
(1)
With the data above filled in this formula the result is:
Z = 144Ω
(2)
d
a
Figure 13. Parallel Wires
Both the measured and the calculated numbers match very closely. The impedance of the flex cable is a physical
parameter so when designing a transmission path using this flex cable, the impedance of the total path must be
based on 140Ω. There is another parameter which is the termination resistance inside the LMH6525 or LMH6526
which is 100Ω. When terminating the 140Ω transmission path with an impedance of 100Ω a mismatch will occur
causing reflections on the transmission line. To solve this problem it is possible to connect directly at the input
terminals of the part two resistors of 20Ω one on every pin to keep it symmetrical. Normally this causes signal
loss over the total extra series resistance of 40Ω when using a voltage source for driving the transmission line.
An advantage of a LVDS source is it’s current nature. The current of a LVDS output is 3.5 mA and this current
produces across a resistor of 140Ω a voltage of 490 mV, while this voltage across the 100Ω internal termination
resistor of the part remains at 350 mV, which is conform the LVDS standard. With the usage of a series
resistance of 40Ω and the termination resistor of 100Ω the total termination resistance now matches the line
impedance and reflections will be as low as possible. A helpful tool for calculating impedances of transmission
lines is the: ‘Transmission Line Rapidesigner’ available from the Texas Instruments Interface Products Group.
Application Note AN-905 (Literature Number SNLA035) details the use of this handy software tool.
The Read Enable and Enable inputs are slower and much less critical. The Oscillator Enable input is toggled in
combination with the write pulse so special attention should be given to this signal to insure it is routed cleanly. It
may be desirable to put a termination resistor close to the LMH6526 for the Enable Oscillator line, to achieve the
best turn-on and turn-off performance of the oscillator.
OUTPUTS
In order to achieve the fastest output rise times the layout of the output lines should be short and tight (see
Figure 14). It is intended that the Output B trace be routed under the decoupling capacitor and that the ground
return for the laser be closely coupled to the output and terminated at the ground side of the decoupling
capacitor.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
Figure 14. Laser Connection
The capacitance on the output lines should also be reduced as much as possible. As always the loop area of the
laser current should be minimized and keep in mind that it is important not to have vias in the current path of the
output lines. Via’s will introduce some inductance which lead to extra overshoot on the pulse shape.
DECOUPLING CAPACITORS
As mentioned before, the decoupling capacitors are critical to the performance of the part. The output section
above mentioned that the power-side decoupling capacitor should be as close as possible to the VDD and GND
pins and that the B output should pass under the decoupling capacitor. Similarly the analog-side decoupling
capacitor should be as close as possible to the VDDA and GNDA pins. Figure 15 shows a layout where the
analog (VDDA and GNDA) decoupling cap C1 is placed next to pins 6 and 7. (Note the layout is rotated 90
degrees from the last figure.) The ground extends into a plane that should connect to the oscillator amplitude and
current setting resistors. C2 is the power-side decoupling capacitor and it can be seen placed as close to the VDD
and GNDB pins as possible while straddling the B output trace. This layout has also provided for a second power
decoupling capacitor C3 that connects from VDD to a different GND copper pour. It must be noted that the two
ground planes extending from C2 and C3 must be tied together. This will be shown in the thermal section below.
Bear in mind that the closeness of the parts to the LMH6525/6526 may be dictated by manufacturing rework
considerations such that the LMH6525/6526 can be de-soldered with a hot-air rework station without the need to
remove the capacitors. The relevant manufacturing organization can provide guidelines for this minimum
spacing.
16
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
Figure 15. Decoupling Capacitors
OSCILLATOR RESISTORS
The resistors and/or potentiometers used to set oscillator frequency or amplitude should be as close to the part
as possible. If the grounds are split when using a single-sided flex circuit, it is essential that these resistors and
potentiometers share the same ground as the GNDA pin and decoupling capacitor.
THERMAL
As mentioned previously, the primary way to get heat out of the QFN package is by the large Die Attach Pad at
the center of the part’s underside. On two-layer circuits this can be done with vias. On single-sided circuits the
pad should connect with a copper pour to either the GND pin or, if a better thermal path can be achieved, with
the VDD pins. Be aware that the unused pins on the part can also be used to connect a copper pour area to the
Die Attach Pad. Figure 16 Heat Sinking (with the same orientation as the first layout example) shows using the
unused pin to provide a thermal path to copper pour heat sinks. In this layout the analog ground has been
separated from the power ground so pin 7 is not connected to the Die Attach Paddle even though it would help
remove heat from the part. The above layout is based on a single-sided circuit board. If a dual-sided circuit board
was used there would also be vias on the Die Attach Pad that would conduct heat to a copper plane on the
bottom side of the board.
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
www.ti.com
Figure 16. Heat Sinking
18
Submit Documentation Feedback
Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LMH6525 LMH6526
LMH6525, LMH6526
www.ti.com
SNOSAF1B –JUNE 2005–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision A (March 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 18
Copyright © 2005–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LMH6525 LMH6526
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LMH6525SP/NOPB
LMH6526SP/NOPB
ACTIVE
ACTIVE
UQFN
UQFN
NJD
NJD
28
28
1000 RoHS & Green
1000 RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
L6525SP
L6526SP
SN
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMH6525SP/NOPB
LMH6526SP/NOPB
UQFN
UQFN
NJD
NJD
28
28
1000
1000
178.0
178.0
12.4
12.4
5.3
5.3
5.3
5.3
1.3
1.3
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Aug-2022
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LMH6525SP/NOPB
LMH6526SP/NOPB
UQFN
UQFN
NJD
NJD
28
28
1000
1000
208.0
208.0
191.0
191.0
35.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
NJD0028A
SPA28A (Rev A)
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明