LMV861MG/NOPB [TI]
Single, 5.5-V, 31-MHz, high output current (150-mA), low noise (8-nV/√Hz) operational amplifier | DCK | 5 | -40 to 125;
| 型号： | LMV861MG/NOPB |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | Single, 5.5-V, 31-MHz, high output current (150-mA), low noise (8-nV/√Hz) operational amplifier | DCK | 5 | -40 to 125 放大器 光电二极管 |
| 文件： | 总31页 (文件大小：1575K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
LMV861/LMV862 30 MHz Low Power CMOS, EMI Hardened Operational Amplifiers
Check for Samples: LMV861, LMV862
1
FEATURES
DESCRIPTION
TI’s LMV861 and LMV862 are CMOS input, low
power op amp IC's, providing a low input bias current,
a wide temperature range of −40°C to +125°C and
exceptional performance making them robust general
purpose parts. Additionally, the LMV861 and LMV862
are EMI hardened to minimize any interference so
they are ideal for EMI sensitive applications.
2
Unless Otherwise Noted, Typical Values at TA
= 25°C, V+ = 3.3V
•
•
•
•
•
•
•
•
•
•
•
Supply Voltage 2.7V to 5.5V
Supply Current (per Channel) 2.25 mA
Input Offset Voltage 1 mV Max
Input Bias Current 0.1 pA
GBW 30 MHz
The unity gain stable LMV861 and LMV862 feature
30 MHz of bandwidth while consuming only 2.25 mA
of current per channel. These parts also maintain
stability for capacitive loads as large as 200 pF. The
LMV861 and LMV862 provide superior performance
and economy in terms of power and space usage.
EMIRR at 1.8 GHz 105 dB
Input Noise Voltage at 1 kHz 8 nV/√Hz
Slew Rate 18 V/µs
Output Voltage Swing Rail-to-Rail
Output Current Drive 67 mA
This family of parts has a maximum input offset
voltage of 1 mV, a rail-to-rail output stage and an
input common-mode voltage range that includes
ground. Over an operating range from 2.7V to 5.5V
the LMV861 and LMV862 provide a PSRR of 93 dB,
and a CMRR of 93 dB. The LMV861 is offered in the
space saving 5-Pin SC70 package, and the LMV862
in the 8-Pin VSSOP.
Operating Ambient Temperature Range −40°C
to 125°C
APPLICATIONS
•
•
•
•
Photodiode Preamp
Weight Scale Systems
Filters/Buffers
Medical Diagnosis Equipment
Typical Application
R1
+
V
NO RF RELATED
DISTURBANCES
R2
PRESSURE
SENSOR
-
-
-
+
+
ADC
+
EMI HARDENED
EMI HARDENED
INTERFERING
RF SOURCES
Figure 1. EMI Hardened Sensor Application
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2013, Texas Instruments Incorporated
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
Human Body Model
Charge-Device Model
Machine Model
2 kV
ESD Tolerance(3)
1 kV
200V
VIN Differential
Supply Voltage (VS = V+ – V−)
± Supply Voltage
6V
Voltage at Input/Output Pins
V+ +0.4V
V− −0.4V
Storage Temperature Range
Junction Temperature(4)
Soldering Information
−65°C to +150°C
+150°C
Infrared or Convection (20 sec)
260°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics Tables.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of
JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
(4) The maximum power dissipation is a function of TJ(MAX), θJA and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) - TA)/ θJA . All numbers apply for packages soldered directly onto a PC board.
Operating Ratings(1)
Temperature Range(2)
Supply Voltage (VS = V+ – V−)
−40°C to +125°C
2.7V to 5.5V
302°C/W
(2)
Package Thermal Resistance (θJA
)
5-Pin SC70
8-Pin VSSOP
217°C/W
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the Electrical Characteristics Tables.
(2) The maximum power dissipation is a function of TJ(MAX), θJA and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) - TA)/ θJA . All numbers apply for packages soldered directly onto a PC board.
3.3V Electrical Characteristics(1)
Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 3.3V, V− = 0V, VCM = V+/2, and RL =10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Input Offset Voltage(4)
Conditions
Min(2)
Typ(3)
Max(2)
Units
VOS
±273
±1000
1260
μV
TCVOS Input Offset Voltage Temperature
Drift(4)(5)
±0.7
0.1
1
±2.6
μV/°C
IB
Input Bias Current(5)
10
500
pA
pA
IOS
Input Offset Current
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No assurance of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ > TA.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlations using
statistical quality control (SQC) method.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
(4) The typical value is calculated by applying absolute value transform to the distribution, then taking the statistical average of the resulting
distribution
(5) This parameter is specified by design and/or characterization and is not tested in production.
2
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
3.3V Electrical Characteristics(1) (continued)
Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 3.3V, V− = 0V, VCM = V+/2, and RL =10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
0.2V ≤ VCM ≤ V+ - 1.2V
Min(2)
Typ(3)
Max(2)
Units
CMRR Common-Mode Rejection Ratio(4)
77
75
93
dB
PSRR
Power Supply Rejection Ratio(4)
2.7V ≤ V+ ≤ 5.5V,
VOUT = 1V
77
76
93
70
dB
dB
EMIRR EMI Rejection Ratio, IN+ and IN−(6)
VRF_PEAK = 100 mVP (−20 dBVP),
f = 400 MHz
VRF_PEAK = 100 mVP (−20 dBVP),
f = 900 MHz
80
VRF_PEAK = 100 mVP (−20 dBVP),
f = 1800 MHz
105
110
VRF_PEAK = 100 mVP (−20 dBVP),
f = 2400 MHz
CMVR Input Common-Mode Voltage Range
CMRR ≥ 65 dB
−0.1
2.1
V
AVOL
Large Signal Voltage Gain(7)
RL = 2 kΩ
VOUT = 0.15V to 1.65V,
VOUT = 3.15V to 1.65V
100
97
110
113
dB
RL = 10 kΩ
100
VOUT = 0.1V to 1.65V,
VOUT = 3.2V to 1.65V
98
VOUT
Output Voltage Swing High
LMV861,
12
12
3
14
18
RL = 2 kΩ to V+/2
LMV862,
16
19
RL = 2 kΩ to V+/2
LMV861,
4
5
RL = 10 kΩ to V+/2
LMV862,
3
6
7
RL = 10 kΩ to V+/2
mV from
either rail
Output Voltage Swing Low
LMV861,
8
12
16
RL = 2 kΩ to V+/2
LMV862,
10
2
14
17
RL = 2 kΩ to V+/2
LMV861,
4
5
RL = 10 kΩ to V+/2
LMV862,
3
7
8
RL = 10 kΩ to V+/2
IOUT
Output Short Circuit Current
Supply Current
Sourcing, VOUT = VCM
VIN = 100 mV
,
61
52
70
86
2.25
4.42
18
mA
Sinking, VOUT = VCM
,
72
58
VIN = −100 mV
IS
LMV861
2.59
3.00
mA
LMV862
5.02
5.77
SR
Slew Rate(8)
AV = +1, VOUT = 1 VPP
,
V/μs
10% to 90%
GBW
Φm
Gain Bandwidth Product
Phase Margin
30
70
MHz
deg
en
Input Referred Voltage Noise Density
f = 1 kHz
f = 100 kHz
f = 1 kHz
8
nV/√Hz
pA/√Hz
5
in
Input Referred Current Noise Density
0.015
(6) The EMI Rejection Ratio is defined as EMIRR = 20log ( VRF_PEAK/ΔVOS).
(7) The specified limits represent the lower of the measured values for each output range condition.
(8) Number specified is the slower of positive and negative slew rates.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
3.3V Electrical Characteristics(1) (continued)
Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 3.3V, V− = 0V, VCM = V+/2, and RL =10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
ROUT
CIN
Parameter
Conditions
Min(2)
Typ(3)
Max(2)
Units
Closed Loop Output Impedance
Common-Mode Input Capacitance
Differential-Mode Input Capacitance
f = 20 MHz
80
Ω
21
pF
%
15
THD+N Total Harmonic Distortion + Noise
f = 1 kHz, AV = 1, BW ≥ 500 kHz
0.02
5V Electrical Characteristics(1)
Unless otherwise specified, all limits are ensured for T = 25°C, V+ = 5V, V− = 0V, VCM = V+/2, and RL =10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Input Offset Voltage(4)
Conditions
Min(2)
Typ(3)
Max(2)
Units
μV
VOS
±273
±1000
1260
TCVOS Input Offset Voltage Temperature
Drift(4)(5)
±0.7
0.1
±2.6
μV/°C
IB
Input Bias Current(5)
10
500
pA
pA
dB
IOS
Input Offset Current
1
CMRR Common-Mode Rejection Ratio(4)
0V ≤ VCM ≤ V+ –1.2V
78
77
94
PSRR
Power Supply Rejection Ratio(4)
2.7V ≤ V+ ≤ 5.5V,
VOUT = 1V
77
76
93
70
dB
EMIRR EMI Rejection Ratio, IN+ and IN−(6)
VRF_PEAK = 100 mVP (−20 dBVP),
f = 400 MHz
VRF_PEAK = 100 mVP (−20 dBVP),
80
f = 900 MHz
dB
VRF_PEAK = 100 mVP (−20 dBVP),
f = 1800 MHz
105
110
VRF_PEAK = 100 mVP (−20 dBVP),
f = 2400 MHz
CMVR Input Common-Mode Voltage Range
CMRR ≥ 65 dB
−0.1
3.9
V
AVOL
Large Signal Voltage Gain(7)
RL = 2 kΩ
VOUT = 0.15V to 2.5V,
VOUT = 4.85V to 2.5V
103
100
111
113
dB
RL = 10 kΩ
103
VOUT = 0.1V to 2.5V,
VOUT = 4.9V to 2.5V
100
(1) Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No assurance of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ > TA.
(2) Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlations using
statistical quality control (SQC) method.
(3) Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary
over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped
production material.
(4) The typical value is calculated by applying absolute value transform to the distribution, then taking the statistical average of the resulting
distribution
(5) This parameter is specified by design and/or characterization and is not tested in production.
(6) The EMI Rejection Ratio is defined as EMIRR = 20log ( VRF_PEAK/ΔVOS).
(7) The specified limits represent the lower of the measured values for each output range condition.
4
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
5V Electrical Characteristics(1) (continued)
Unless otherwise specified, all limits are ensured for T = 25°C, V+ = 5V, V− = 0V, VCM = V+/2, and RL =10 kΩ to V+/2.
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Min(2)
Typ(3)
Max(2)
Units
VOUT
Output Voltage Swing High,
LMV861,
13
15
19
RL = 2 kΩ to V+/2
LMV862,
13
3
17
20
RL = 2 kΩ to V+/2
LMV861,
4
5
RL = 10 kΩ to V+/2
LMV862,
3
6
7
RL = 10 kΩ to V+/2
mV from
either rail
Output Voltage Swing Low,
LMV861,
10
12
3
14
18
RL = 2 kΩ to V+/2
LMV862,
17
20
RL = 2 kΩ to V+/2
LMV861,
4
5
RL = 10 kΩ to V+/2
LMV862,
3
7
8
RL = 10 kΩ to V+/2
IOUT
Output Short Circuit Current
Supply Current
Sourcing, VOUT = VCM
VIN = 100 mV
,
90
86
150
150
2.47
4.85
20
mA
Sinking, VOUT = VCM
,
90
86
VIN = −100 mV
IS
LMV861
2.84
3.27
mA
LMV862
5.63
6.35
SR
Slew Rate(8)
AV = +1, VOUT = 2VPP
,
V/μs
10% to 90%
GBW
Φm
Gain Bandwidth Product
Phase Margin
31
71
MHz
deg
en
Input Referred Voltage Noise Density
f = 1 kHz
8
nV/√Hz
f = 100 kHz
f = 1 kHz
5
in
Input Referred Current Noise Density
Closed Loop Output Impedance
Common-Mode Input Capacitance
Differential-Input Capacitance
0.015
60
pA/√Hz
ROUT
CIN
f = 20 MHz
Ω
20
pF
%
15
THD+N Total Harmonic Distortion + Noise
f = 1 kHz, AV= 1, BW ≥ 500 kHz
0.02
(8) Number specified is the slower of positive and negative slew rates.
Connection Diagram
Figure 2. 5-Pin SC70
(Top View)
Figure 3. 8-Pin VSSOP
(Top View)
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
At TA = 25°C. RL = 10 kΩ, V+ = 3.3V, V− = 0V, unless otherwise specified.
VOS vs. VCM at V+ = 3.3V
VOS vs. VCM at V+ = 5.0V
0.3
0.2
0.1
0
0.3
0.2
0.1
0
-40°C
25°C
-40°C
25°C
-0.1
-0.2
-0.3
-0.1
-0.2
-0.3
85°C
85°C
125°C
125°C
+
+
V
= 5.0V
0.5
V
= 3.3V
-0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
(V)
-0.5
1.5
2.5
(V)
3.5
4.5
5.5
V
V
CM
CM
Figure 4.
Figure 5.
VOS vs. Supply Voltage
VOS vs. Temperature
0.3
0.2
0.1
0
200
150
100
50
-40°C
3.3V
0
-50
-0.1
-0.2
-0.3
25°C
85°C
-100
-150
-200
5.0V
125°C
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
-50 -25
0
25
50
75 100 125
V
(V)
TEMPERATURE (°C)
SUPPLY
Figure 6.
Figure 7.
VOS vs. VOUT
Input Bias Current vs. VCM at 25°C
= 25°C
+
T
A
V
= 5.0V, R = 2k
L
12
9
5
4
6
3
5V
2
3
1
0
0
-1
-2
-3
-4
-5
-3
-6
-9
-12
3.3V
0
1
2
3
4
5
-1
0
1
2
3
4
5
6
V
(V)
OUT
V
(V)
CM
Figure 8.
Figure 9.
6
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
Typical Performance Characteristics (continued)
At TA = 25°C. RL = 10 kΩ, V+ = 3.3V, V− = 0V, unless otherwise specified.
Input Bias Current vs. VCM at 85°C
Input Bias Current vs. VCM at 125°C
T
A
= 125°C
T
A
= 85°C
50
40
500
400
300
200
100
0
30
20
5.0V
10
0
-10
-20
-30
-40
-50
-100
-200
-300
-400
-500
5.0V
3.3V
3.3V
-1
0
1
2
3
4
5
6
-1
0
1
2
3
4
5
6
V
(V)
V
(V)
CM
CM
Figure 10.
Figure 11.
Supply Current vs. Supply Voltage Single LMV861
Supply Current vs. Supply Voltage Dual LMV862
3.4
6.0
125°C
85°C
3.2
5.5
5.0
125°C
3.0
85°C
2.8
2.6
2.4
4.5
25°C
25°C
2.2
4.0
-40°C
2.0
-40°C
3.5
1.8
1.6
3.0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 12.
Figure 13.
Supply Current vs. Temperature Single LMV861
Supply Current vs. Temperature Dual LMV862
3.2
6.5
3.0
6.0
2.8
5.0V
5.5
5.0V
2.6
2.4
5.0
4.5
2.2
3.3V
3.3V
4.0
3.5
3.0
2.0
1.8
1.6
-50 -25
0
25
50
75 100 125
-50 -25
0
25
50
75 100 125
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 14.
Figure 15.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
At TA = 25°C. RL = 10 kΩ, V+ = 3.3V, V− = 0V, unless otherwise specified.
Sinking Current vs. Supply Voltage
Sourcing Current vs. Supply Voltage
250
200
250
200
150
100
50
25°C
-40°C
25°C
-40°C
150
100
50
125°C
85°C
85°C 125°C
0
0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
Figure 16.
Figure 17.
Output Swing High vs. Supply Voltage RL = 2 kΩ
Output Swing High vs. Supply Voltage RL = 10 kΩ
20
5
4
3
2
1
0
15
10
5
0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 18.
Figure 19.
Output Swing Low vs. Supply Voltage RL = 2 kΩ
Output Swing Low vs. Supply Voltage RL = 10 kΩ
20
5
4
3
2
1
0
15
10
5
0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Figure 20.
Figure 21.
8
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
Typical Performance Characteristics (continued)
At TA = 25°C. RL = 10 kΩ, V+ = 3.3V, V− = 0V, unless otherwise specified.
Output Voltage Swing vs. Load Current at V+ = 3.3V
Output Voltage Swing vs. Load Current at V+ = 5.0V
SINK
SINK
125°C
125°C
1.0
1.0
0.8
0.6
0.4
0.2
0.8
0.6
0.4
0.2
+
+
0
0
-40°C
V = 5.0V
V
= 3.3V
-40°C
-0.2
-0.4
-0.6
-0.8
-1.0
-0.2
-0.4
-0.6
-0.8
-1.0
125°C
125°C
SOURCE
SOURCE
10 20 30 40 50 60 70 80
(mA)
0
10 20 30 40 50 60 70 80
(mA)
0
I
I
LOAD
LOAD
Figure 22.
Figure 23.
Open Loop Frequency Response vs. Temperature
Open Loop Frequency Response vs. Load Conditions
25°C
85°C
125°C
20 pF
80
70
60
50
40
30
20
10
0
120
105
90
75
60
45
30
15
0
80
70
60
50
40
30
20
10
0
120
105
90
75
60
45
30
15
0
PHASE
5 pF
GAIN
100 pF
50 pF
25°C
85°C
125°C
C
= 5 pF
L
5 pF
= 20 pF
= 50 pF
= 100 pF
-40°C
100 pF
10M
10k
100k
1M
100M
10k
100k
1M
10M
100M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 24.
Figure 25.
Phase Margin vs. Capacitive Load
PSRR vs. Frequency
120
100
80
60
40
20
0
80
70
60
50
40
30
20
10
0
3.3V
5.0V
-PSRR
3.3V
5.0V
+PSRR
100k
+
V
= 3.3V, 5.0V
1
10
100
(pF)
1000
100
1k
10k
1M
10M
FREQUENCY (Hz)
C
LOAD
Figure 26.
Figure 27.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
At TA = 25°C. RL = 10 kΩ, V+ = 3.3V, V− = 0V, unless otherwise specified.
CMRR vs. Frequency
Channel Separation vs. Frequency
AC CMRR
100
160
140
120
100
80
80
60
40
20
DC CMRR
60
+
10k
V
= 3.3V, 5.0V
1k
100
10k
100k
1M
10M
1k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 28.
Figure 29.
Large Signal Step Response with Gain = 1
Large Signal Step Response with Gain = 10
f = 1 MHz
f = 1 MHz
A
V
= +1
A
V
= +10
V
IN
= 500 mV
V
IN
= 100 mV
PP
PP
100 ns/DIV
100 ns/DIV
Figure 30.
Figure 31.
Small Signal Step Response with Gain = 1
Small Signal Step Response with Gain = 10
f = 1 MHz
f = 1 MHz
A
= +1
A
V
= +10
V
V
V
IN
= 100 mV
= 10 mV
PP
IN
PP
100 ns/DIV
100 ns/DIV
Figure 32.
Figure 33.
10
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
Typical Performance Characteristics (continued)
At TA = 25°C. RL = 10 kΩ, V+ = 3.3V, V− = 0V, unless otherwise specified.
Slew Rate vs. Supply Voltage
Input Voltage Noise vs. Frequency
30
100
10
1
28
26
FALLING EDGE
RISING EDGE
24
22
20
18
16
14
12
10
A
V
C
L
= +1
= 5 pF
+
V
= 3.3V, 5.0V
100
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
10
1k
10k
100k
1M
FREQUENCY (Hz)
SUPPLY VOLTAGE (V)
Figure 34.
Figure 35.
THD+N vs. Frequency
THD+N vs. Amplitude
+
BW = >500 kHz
V
= 5.0V
0.1
0.01
10
1
+
A
V
= 10x
V
= 3.3V
A
= 10x
V
+
V =3.3V, V =320 mV
IN
PP
V+=5.0V, VIN=480 mVPP
V+=3.3V, VIN=2.3 VPP
A
= 1x
V
0.1
0.001
0.0001
0.01
0.001
+
V =5.0V, V =3.8 V
IN PP
A
= 1x
V
f = 1 kHz
BW = >500 kHz
10
100
1k
10k
100k
1m 10m
100m
(V
1
10
V
)
OUT PP
FREQUENCY (Hz)
Figure 36.
Figure 37.
ROUT vs. Frequency
EMIRR IN+ vs. Power at 400 MHz
100
10
100
120
110
100
90
80
60
40
20
0
1
80
70
0.1
60
50
100k
0.01
40
30
f
= 400 MHz
RF
0.001
20
-40
100
1k
10k
1M
10M
-30
-20
-10
0
10
FREQUENCY (Hz)
RF INPUT PEAK VOLTAGE (dBVp)
Figure 38.
Figure 39.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
At TA = 25°C. RL = 10 kΩ, V+ = 3.3V, V− = 0V, unless otherwise specified.
EMIRR IN+ vs. Power at 900 MHz
EMIRR IN+ vs. Power at 1800 MHz
120
120
110
100
90
110
100
90
80
70
60
50
40
30
20
80
70
60
50
40
30
f
= 900 MHz
-30
RF
20
-40
-40
-20
-10
0
10
-30
-20
-10
0
10
RF INPUT PEAK VOLTAGE (dBVp)
RF INPUT PEAK VOLTAGE (dBVp)
Figure 40.
Figure 41.
EMIRR IN+ vs. Power at 2400 MHz
EMIRR IN+ vs. Frequency
120
110
100
90
80
70
60
50
40
30
20
120
110
100
90
80
70
60
50
40
30
20
-40°C
+
V
= 3.3V, 5.0V
V
= -20 dBVp
RF PEAK
f
= 2400 MHz
RF
-40
-30
-20
-10
0
10
10
100
1000
10000
FREQUENCY (MHz)
RF INPUT PEAK VOLTAGE (dBVp)
Figure 42.
Figure 43.
12
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
APPLICATION INFORMATION
INTRODUCTION
The LMV861 and LMV862 are operational amplifiers with excellent specifications, such as low offset, low noise
and a rail-to-rail output. These specifications make the LMV861 and LMV862 great choices for medical and
instrumentation applications such as diagnosis equipment and power line monitors. The low supply current is
perfect for battery powered equipment. The small packages, SC70 package for the LMV861, and the VSSOP
package for the dual LMV862, make these parts a perfect choice for portable electronics. Additionally, the EMI
hardening makes the LMV861 and LMV862 a must for almost all op amp applications. Most applications are
exposed to Radio Frequency (RF) signals such as the signals transmitted by mobile phones or wireless
computer peripherals. The LMV861 and LMV862 will effectively reduce disturbances caused by RF signals to a
level that will be hardly noticeable. This again reduces the need for additional filtering and shielding. Using this
EMI resistant series of op amps will thus reduce the number of components and space needed for applications
that are affected by EMI, and will help applications, not yet identified as possible EMI sensitive, to be more robust
for EMI.
INPUT CHARACTERISTICS
The input common mode voltage range of the LMV861 and LMV862 includes ground, and can even sense well
below ground. The CMRR level does not degrade for input levels up to 1.2V below the supply voltage. For a
supply voltage of 5V, the maximum voltage that should be applied to the input for best CMRR performance is
thus 3.8V.
When not configured as unity gain, this input limitation will usually not degrade the effective signal range. The
output is rail-to-rail and therefore will introduce no limitations to the signal range.
The typical offset is only 0.273 mV, and the TCVOS is 0.7 μV/°C, specifications close to precision op amps.
CMRR MEASUREMENT
The CMRR measurement results may need some clarification. This is because different setups are used to
measure the AC CMRR and the DC CMRR.
The DC CMRR is derived from ΔVOS versus ΔVCM. This value is stated in the tables, and is tested during
production testing. The AC CMRR is measured with the test circuit shown in Figure 44.
R2
1 kW
+
V
BUFFER
+
V
R1
1 kW
-
+
-
V
-
IN
Buffer
V
OUT
LMV86x
+
R11
1 kW
V
BUFFER
-
R12
995W
V
P1
10W
Figure 44. AC CMRR Measurement Setup
The configuration is largely the usually applied balanced configuration. With potentiometer P1, the balance can
be tuned to compensate for the DC offset in the DUT. The main difference is the addition of the buffer. This
buffer prevents the open-loop output impedance of the DUT from affecting the balance of the feedback network.
Now the closed-loop output impedance of the buffer is a part of the balance. But as the closed-loop output
impedance is much lower, and by careful selection of the buffer also has a larger bandwidth, the total effect is
that the CMRR of the DUT can be measured much more accurately. The differences are apparent in the larger
measured bandwidth of the AC CMRR.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
One artifact from this test circuit is that the low frequency CMRR results appear higher than expected. This is
because in the AC CMRR test circuit the potentiometer is used to compensate for the DC mismatches. So,
mainly AC mismatch is all that remains. Therefore, the obtained DC CMRR from this AC CMRR test circuit tends
to be higher than the actual DC CMRR based on DC measurements.
The CMRR curve in Figure 45 shows a combination of the AC CMRR and the DC CMRR.
AC CMRR
100
80
60
40
20
DC CMRR
+
V
= 3.3V, 5.0V
1k
100
10k
100k
1M
10M
FREQUENCY (Hz)
Figure 45. CMRR Curve
OUTPUT CHARACTERISTICS
As already mentioned the output is rail-to-rail. When loading the output with a 10 kΩ resistor the maximum swing
of the output is typically 3 mV from the positive and negative rail.
The output of the LMV861 and LMV862 can drive currents up to 70 mA at 3.3V, and even up to 150 mA at 5V.
The LMV861 and LMV862 can be connected as non-inverting unity gain amplifiers. This configuration is the most
sensitive to capacitive loading. The combination of a capacitive load placed at the output of an amplifier along
with the amplifier’s output impedance creates a phase lag, which reduces the phase margin of the amplifier. If
the phase margin is significantly reduced, the response will be under damped which causes peaking in the
transfer and, when there is too much peaking, the op amp might start oscillating. The LMV861 and LMV862 can
directly drive capacitive loads up to 200 pF without any stability issues. In order to drive heavier capacitive loads,
an isolation resistor, RISO, should be used, as shown in Figure 46. By using this isolation resistor, the capacitive
load is isolated from the amplifier’s output, and hence, the pole caused by CL is no longer in the feedback loop.
The larger the value of RISO, the more stable the amplifier will be. If the value of RISO is sufficiently large, the
feedback loop will be stable, independent of the value of CL. However, larger values of RISO result in reduced
output swing and reduced output current drive.
R
ISO
-
V
OUT
V
+
IN
C
L
Figure 46. Isolating Capacitive Load
A resistor value of around 50Ω would be sufficient. As an example some values are given in the following table,
for 5V and an open loop gain of 111 dB.
CLOAD
300 pF
400 pF
500 pF
RISO
62Ω
55Ω
50Ω
14
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
When increasing the closed-loop gain the capacitive load can be increased even further. With a closed loop gain
of 2 and a 27Ω isolation resistor, the load can be 1 nF
EMIRR
With the increase of RF transmitting devices in the world, the electromagnetic interference (EMI) between those
devices and other equipment becomes a bigger challenge. The LMV861 and LMV862 are EMI hardened op
amps which are specifically designed to overcome electromagnetic interference. Along with EMI hardened op
amps, the EMIRR parameter is introduced to unambiguously specify the EMI performance of an op amp. This
section presents an overview of EMIRR. A detailed description on this specification for EMI hardened op amps
can be found in Application Note AN-1698.
The dimensions of an op amp IC are relatively small compared to the wavelength of the disturbing RF signals. As
a result the op amp itself will hardly receive any disturbances. The RF signals interfering with the op amp are
dominantly received by the PCB and wiring connected to the op amp. As a result the RF signals on the pins of
the op amp can be represented by voltages and currents. This representation significantly simplifies the
unambiguous measurement and specification of the EMI performance of an op amp.
RF signals interfere with op amps via the non-linearity of the op amp circuitry. This non-linearity results in the
detection of the so called out-of-band signals. The obtained effect is that the amplitude modulation of the out-of-
band signal is downconverted into the base band. This base band can easily overlap with the band of the op
amp circuit. As an example Figure 47 depicts a typical output signal of a unity-gain connected op amp in the
presence of an interfering RF signal. Clearly the output voltage varies in the rhythm of the on-off keying of the RF
carrier.
RF
NO RF
RF SIGNAL
V
+ V
DETECTED
OS
V
OUT OPAMP
(A = 1)
V
V
OS
Figure 47. Offset voltage variation due to an interfering RF signal
EMIRR Definition
To identify EMI hardened op amps, a parameter is needed that quantitatively describes the EMI performance of
op amps. A quantitative measure enables the comparison and the ranking of op amps on their EMI robustness.
Therefore the EMI Rejection Ratio (EMIRR) is introduced. This parameter describes the resulting input-referred
offset voltage shift of an op amp as a result of an applied RF carrier (interference) with a certain frequency and
level. The definition of EMIRR is given by:
≈
∆
∆
«
’
÷
÷
◊
VRF_PEAK
EMIRRV
RF_PEAK = 20 log
DVOS
where
•
•
VRF_PEAK is the amplitude of the applied un-modulated RF signal (V)
ΔVOS is the resulting input-referred offset voltage shift (V)
(1)
The offset voltage depends quadratically on the applied RF level, and therefore, the RF level at which the EMIRR
is determined should be specified. The standard level for the RF signal is 100 mVP. Application Note AN-1698
addresses the conversion of an EMIRR measured for an other signal level than 100 mVP. The interpretation of
the EMIRR parameter is straightforward. When two op amps have EMIRRs which differ by 20 dB, the resulting
error signals when used in identical configurations, differs by 20 dB as well. So, the higher the EMIRR, the more
robust the op amp.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
Coupling an RF Signal to the IN+ Pin
Each of the op amp pins can be tested separately on EMIRR. In this section the measurements on the IN+ pin
(which, based on symmetry considerations, also apply to the IN- pin) are discussed. In Application Note AN-1698
the other pins of the op amp are treated as well. For testing the IN+ pin the op amp is connected in the unity gain
configuration. Applying the RF signal is straightforward as it can be connected directly to the IN+ pin. As a result
the RF signal path has a minimum of components that might affect the RF signal level at the pin. The circuit
diagram is shown in Figure 48. The PCB trace from RFIN to the IN+ pin should be a 50Ω stripline in order to
match the RF impedance of the cabling and the RF generator. On the PCB a 50Ω termination is used. This 50Ω
resistor is also used to set the bias level of the IN+ pin to ground level. For determining the EMIRR, two
measurements are needed: one is measuring the DC output level when the RF signal is off; and the other is
measuring the DC output level when the RF signal is switched on. The difference of the two DC levels is the
output voltage shift as a result of the RF signal. As the op amp is in the unity gain configuration, the input
referred offset voltage shift corresponds one-to-one to the measured output voltage shift.
C
2
V
DD
10 µF
C
3
100 pF
RFin
+
-
Out
R
1
50W
C
4
C
1
100 pF
22 pF
C
5
V
SS
10 µF
Figure 48. Circuit for coupling the RF signal to IN+
Cell Phone Call
The effect of electromagnetic interference is demonstrated in a setup where a cell phone interferes with a
pressure sensor application. The application is show in Figure 50.
This application needs two op amps and therefore a dual op amp is used. The op amp configured as a buffer
and connected at the negative output of the pressure sensor prevents the loading of the bridge by resistor R2.
The buffer also prevents the resistors of the sensor from affecting the gain of the following gain stage. The op
amps are placed in a single supply configuration.
The experiment is performed on two different op amps: a typical standard op amp and the LMV862, EMI
hardened dual op amp. A cell phone is placed on a fixed position a couple of centimeters from the op amps in
the sensor circuit.
When the cell phone is called, the PCB and wiring connected to the op amps receive the RF signal.
Subsequently, the op amps detect the RF voltages and currents that end up at their pins. The resulting effect on
the output of the second op amp is shown in Figure 49.
16
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
Typical Opamp
LMV862
TIME (0.5s/DIV)
Figure 49. Comparing EMI Robustness
The difference between the two types of op amps is clearly visible. The typical standard dual op amp has an
output shift (disturbed signal) larger than 1V as a result of the RF signal transmitted by the cell phone. The
LMV862, EMI hardened op amp does not show any significant disturbances. This means that the RF signal will
not disturb the signal entering the ADC when using the LMV862.
R1
2.4 kW
V
DD
V
DD
R2
100W
PRESSURE
SENSOR
-
LMV862
+
-
-
+
ADC
LMV862
V
OUT
+
Figure 50. Pressure Sensor Application
DECOUPLING AND LAYOUT
Care must be given when creating a board layout for the op amp. For decoupling the supply lines it is suggested
that 10 nF capacitors be placed as close as possible to the op amp. For single supply, place a capacitor between
V+ and V−. For dual supplies, place one capacitor between V+ and the board ground, and a second capacitor
between ground and V−.
Even with the LMV861 and LMV862 inherent hardening against EMI, it is still recommended to keep the input
traces short and as far as possible from RF sources. Then the RF signals entering the chip are as low as
possible, and the remaining EMI can be, almost, completely eliminated in the chip by the EMI reducing features
of the LMV861 and LMV862.
LOAD CELL SENSOR APPLICATION
The LMV861 and LMV862 can be used for weight measuring system applications which use a load cell sensor.
Examples of such systems are: bathroom weight scales, industrial weight scales and weight measurement
devices on moving equipment such as forklift trucks.
The following example describes a typical load cell sensor application that can be used as a starting point for
many different types of sensors and applications. Applications in environments where EMI may appear would
especially benefit from the EMIRR performance of the LMV861 and LMV862.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
Load Cell Characteristics
The load cell used in this example is a Wheatstone bridge. The value of the resistors in the bridge changes when
pressure is applied to the sensor. This change of the resistor values will result in a differential output voltage
depending on the sensitivity of the sensor, the used supply voltage and the applied pressure. The difference
between the output at full scale pressure and the output at zero pressure is defined as the span of the load cell.
A typical value for the span is 10 mV/V.
The circuit configuration should be chosen such that loading of the sensor is prevented. Loading of the resistor
bridge due to the circuit following the sensor, could result in incorrect output voltages of the sensor.
Load Cell Example
Figure 51 shows a typical schematic for a load cell application. It uses a single supply and has an adjustment for
both positive and negative offset of the load cell. An ADC converts the amplified signal to a digital signal.
The op amps A1 and A2 are configured as buffers, and are connected at both the positive and the negative
output of the load cell. This is to prevent the loading of the resistor bridge in the sensor by the resistors
configuring the differential op amp circuit (op amp A4). The buffers also prevent the resistors of the sensor from
affecting the gain of the following gain stage. The third buffer (A3) is used to create a reference voltage, to
correct for the offset in the system.
Given the differential output voltage VS of the load cell, the output signal of this op amp configuration, VOUT
,
equals:
«
R3
R1
R3
« R5
R3
R5
≈
≈
x VSENSE +
1
+
x VDD
x VREF
-
VOUT
=
(2)
To align the pressure range with the full range of an ADC the correct gain needs to be set. To calculate the
correct gain, the power supply voltage and the span of the load cell are needed. For this example a power supply
of 5V is used and the span of the sensor, in this case a 125 kg sensor, is 100 mV. With the configuration as
shown in Figure 51, this signal is covering almost the full input range of the ADC. With no weight on the load cell,
the output of the sensor and the op amp A4 will be close to 0V. With the full weight on the load cell, the output of
the sensor is 100 mV, and will be amplified with the gain from the configuration. In the case of the configuration
of Figure 51 the gain is R3/R1 = 51 kΩ/100Ω = 50. This will result in a maximum output of 100 mV x 50 = 5V,
which covers the full range of the ADC.
For further processing the digital signal can be processed by a microprocessor following the ADC, this can be
used to display or log the weight on the load cell. To get a resolution of 0.5 kg, the LSB of the ADC should be
smaller then 0.5 kg/125 kg = 1/1000. A 12-bit ADC would be sufficient as this gives 4096 steps. A 12-bit ADC
such as the two channel 12-bit ADC122S021 can be used for this application.
18
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
V
DD
R5
5 kW
V
DD
R3
5 kW
A1
R1
LOAD
CELL
-
100W
V
DD
LMV861
+
-
+
A4
-
ADC
LMV861
V
OUT
+
V
SENSE
A2
R2
100W
-
LMV861
+
R4
5 kW
V
DD
R6
80 kW
A3
-
V
REF
LMV861
+
P1
20 kW
R6
80 kW
Figure 51. Load Cell Application
IR PHOTODIODE APPLICATION
The LMV861 and LMV862 are also very good choices to be used in photodiode applications, such as IR
communication, monitoring, etc. The large bandwidth of the LMV861 and LM862 makes it possible to create high
speed detection. This, together with the low noise, makes the LMV861 and LMV862 ideal for medical
applications such as fetal monitors and bed side monitors. Another application where the LMV861 and LMV862
would fit perfectly is a bill validator, an instrument to detect counterfeit bank notes. The following example
describes an application that can be used for different types of photodiode sensors and applications.
IR Photodiode Example
The circuit shown in Figure 53 is a typical configuration for the readout of a photodiode. The response of a
photodiode to incoming light is a variation in the diode current. In many applications a voltage is required, i.e.
when connecting to an ADC. Therefore the first step is to convert the diode signal current into a voltage by an I-V
converter. In Figure 53 the left op amp is configured as an I-V converter, with a gain set by R1.
Some types of photodiodes can have a large capacitance. This could potentially lead to oscillation. The addition
of resistor R2 isolates the photodiode capacitance from the feedback loop, thereby preventing the loop from
oscillating.
The capacitor in between the two op amp configurations, blocks the DC component, thus removing the DC offset
of the first op amp circuit, and the offset created by the ambient light entering the photodiode. The second op
amp amplifies the signal to levels that can be converted to a digital signal by an ADC. To prevent floating of the
input of the second op amp, resistor R5 is added. By allowing the input bias current of a few pA to flow through
this resistor a stable input is ensured.
In Figure 52 a sensed and amplified signal is shown from an IR source, in this case an IR remote control.
The data from the ADC can then be used by a DSP or microprocessor for further processing.
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LMV861 LMV862
LMV861, LMV862
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
www.ti.com
20 µs/DIV
Figure 52. IR Photodiode Signal
R1
100 kW
R5
1 MW
V
DD
R2
330W
V
DD
C1
1 nF
-
LMV861
+
+
V
OUT
ADC
LMV861
IR
-
Photodiode
V
EE
V
EE
R4
V
EE
100W
R3
100 kW
Figure 53. IR Photodiode Application
20
Submit Documentation Feedback
Copyright © 2008–2013, Texas Instruments Incorporated
Product Folder Links: LMV861 LMV862
LMV861, LMV862
www.ti.com
SNOSAZ5C –FEBRUARY 2008–REVISED MARCH 2013
REVISION HISTORY
Changes from Revision B (March 2013) to Revision C
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 19
Copyright © 2008–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LMV861 LMV862
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LMV861MG/NOPB
LMV861MGE/NOPB
LMV861MGX/NOPB
LMV862MM/NOPB
LMV862MMX/NOPB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SC70
SC70
DCK
DCK
DCK
DGK
DGK
5
5
5
8
8
1000 RoHS & Green
250 RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
AEA
AEA
AEA
AJ5A
AJ5A
SN
SN
SN
SN
SC70
3000 RoHS & Green
1000 RoHS & Green
3500 RoHS & Green
VSSOP
VSSOP
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Oct-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LMV861MG/NOPB
LMV861MGE/NOPB
LMV861MGX/NOPB
LMV862MM/NOPB
LMV862MMX/NOPB
SC70
SC70
DCK
DCK
DCK
DGK
DGK
5
5
5
8
8
1000
250
178.0
178.0
178.0
178.0
330.0
8.4
8.4
2.25
2.25
2.25
5.3
2.45
2.45
2.45
3.4
1.2
1.2
1.2
1.4
1.4
4.0
4.0
4.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q1
Q1
SC70
3000
1000
3500
8.4
8.0
VSSOP
VSSOP
12.4
12.4
12.0
12.0
5.3
3.4
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Oct-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
LMV861MG/NOPB
LMV861MGE/NOPB
LMV861MGX/NOPB
LMV862MM/NOPB
LMV862MMX/NOPB
SC70
SC70
DCK
DCK
DCK
DGK
DGK
5
5
5
8
8
1000
250
208.0
208.0
208.0
208.0
367.0
191.0
191.0
191.0
191.0
367.0
35.0
35.0
35.0
35.0
35.0
SC70
3000
1000
3500
VSSOP
VSSOP
Pack Materials-Page 2
PACKAGE OUTLINE
DCK0005A
SOT - 1.1 max height
S
C
A
L
E
5
.
6
0
0
SMALL OUTLINE TRANSISTOR
C
2.4
1.8
0.1 C
1.4
1.1
B
1.1 MAX
A
PIN 1
INDEX AREA
1
2
5
NOTE 4
(0.15)
(0.1)
2X 0.65
1.3
2.15
1.85
1.3
4
3
0.33
5X
0.23
0.1
0.0
(0.9)
TYP
0.1
C A B
0.15
0.22
0.08
GAGE PLANE
TYP
0.46
0.26
8
0
TYP
TYP
SEATING PLANE
4214834/C 03/2023
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-203.
4. Support pin may differ or may not be present.
www.ti.com
EXAMPLE BOARD LAYOUT
DCK0005A
SOT - 1.1 max height
SMALL OUTLINE TRANSISTOR
PKG
5X (0.95)
1
5
5X (0.4)
SYMM
(1.3)
2
3
2X (0.65)
4
(R0.05) TYP
(2.2)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:18X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214834/C 03/2023
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DCK0005A
SOT - 1.1 max height
SMALL OUTLINE TRANSISTOR
PKG
5X (0.95)
1
5
5X (0.4)
SYMM
(1.3)
2
3
2X(0.65)
4
(R0.05) TYP
(2.2)
SOLDER PASTE EXAMPLE
BASED ON 0.125 THICK STENCIL
SCALE:18X
4214834/C 03/2023
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明