LP2989IMMX-2.8 [TI]
2.8V FIXED POSITIVE LDO REGULATOR, 0.65V DROPOUT, PDSO8, MSOP-8;
| 型号： | LP2989IMMX-2.8 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 2.8V FIXED POSITIVE LDO REGULATOR, 0.65V DROPOUT, PDSO8, MSOP-8 光电二极管 输出元件 调节器 |
| 文件： | 总19页 (文件大小：1049K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LP2989
LP2989 Micropower/Low Noise, 500 mA Ultra Low-Dropout RegulatorFor Use
with Ceramic Output Capacitors
Literature Number: SNVS083M
February 2005
LP2989
Micropower/Low Noise, 500 mA Ultra Low-Dropout
Regulator
For Use with Ceramic Output Capacitors
General Description
Features
n Ultra low dropout voltage
The LP2989 is a fixed-output 500 mA precision LDO regu-
lator designed for use with ceramic output capacitors.
n Guaranteed 500 mA continuous output current
n Very low output noise with external capacitor
n SO-8, Mini SO-8, 8 Lead LLP surface mount packages
Output noise can be reduced to 18µV (typical) by connecting
an external 10 nF capacitor to the bypass pin.
<
n
0.8 µA quiescent current when shutdown
™
Using an optimized VIP (Vertically Integrated PNP) pro-
cess, the LP2989 delivers superior performance:
n Low ground pin current at all loads
n 0.75% output voltage accuracy (“A” grade)
n High peak current capability (800 mA typical)
n Wide supply voltage range (16V max)
n Overtemperature/overcurrent protection
n −40˚C to +125˚C junction temperature range
@
Dropout Voltage: Typically 310 mV 500 mA load, and 1
@
mV 100 µA load.
@
Ground Pin Current: Typically 3 mA 500 mA load, and
@
110 µA 100 µA load.
Sleep Mode: The LP2989 draws less than 0.8 µA quiescent
current when shutdown pin is pulled low.
Applications
Error Flag: The built-in error flag goes low when the output
drops approximately 5% below nominal.
n Notebook/Desktop PC
n PDA/Palmtop Computer
n Wireless Communication Terminals
n SMPS Post-Regulator
Precision Output: Guaranteed output voltage accuracy is
0.75% (“A” grade) and 1.25% (standard grade) at room
temperature.
<
For output voltages 2V, see LP2989LV datasheet.
Block Diagram
10133901
™
VIP is a trademark of National Semiconductor Corporation.
© 2005 National Semiconductor Corporation
DS101339
www.national.com
Connection Diagrams
Surface Mount Packages:
8 Lead LLP Surface Mount Package
10133902
SO-8/Mini SO-8 Package
See NS Package Drawing Numbers M08A/MUA08A
10133950
Top View
See NS Package Number LDC08A
Basic Application Circuit
10133903
*Capacitance values shown are minimum required to assure stability, but may be increased without limit. Larger output capacitor provides improved dynamic
response. See Application Hints.
**Shutdown must be actively terminated (see App. Hints). Tie to INPUT (Pin4) if not used
www.national.com
2
Ordering Information
TABLE 1. Package Marking and Ordering Information
Output Voltage
Grade
Order Information
Package Marking
Supplied as:
8 Lead LLP
2.5
A
A
LP2989AILD-2.5
LP2989AILDX-2.5
LP2989ILD-2.5
L01FA
L01FA
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
1000 Units on Tape and Reel
4500 Units on Tape and Reel
2.5
2.5
STD
STD
A
L01FAB
L01FAB
L000A
2.5
LP2989ILDX-2.5
LP2989AILD-2.8
LP2989AILDX-2.8
LP2989ILD-2.8
2.8
2.8
A
L000A
2.8
STD
STD
A
L000AB
L000AB
L01TA
2.8
LP2989ILDX-2.8
LP2989AILD-285
LP2989AILDX-285
LP2989ILD-285
LP2989ILDX-285
LP2989AILD-3.0
LP2989AILDX-3.0
LP2989ILD-3.0
2.85
2.85
A
L01TA
2.85
STD
STD
A
L01TAB
L01TAB
L01HA
L01HA
L01HAB
L01HAB
L01JA
2.85
3.0
3.0
A
3.0
STD
STD
A
3.0
LP2989ILDX-3.0
LP2989AILD-3.3
LP2989AILDX-3.3
LP2989ILD-3.3
3.3
3.3
A
L01JA
3.3
STD
STD
A
L01JAB
L01JAB
L019A
3.3
LP2989ILDX-3.3
LP2989AILD-3.6
LP2989AILDX-3.6
LP2989ILD-3.6
3.6
3.6
A
L019A
3.6
STD
STD
A
L019AB
L019AB
L01LA
3.6
LP2989ILDX-3.6
LP2989AILD-4.0
LP2989AILDX-4.0
LP2989ILD-4.0
4.0
4.0
A
L01LA
4.0
STD
STD
A
L01LAB
L01LAB
L01KA
L01KA
L01KAB
L01KAB
4.0
LP2989ILDX-4.0
LP2989AILD-5.0
LP2989AILDX-5.0
LP2989ILD-5.0
5.0
5.0
A
5.0
STD
STD
5.0
LP2989ILDX-5.0
8 Lead MSOP (MM)
2.5
2.5
2.5
2.5
2.8
2.8
2.8
2.8
3.0
3.0
3.0
3.0
3.3
3.3
A
A
LP2989AIMM-2.5
LP2989AIMMX-2.5
LP2989IMM-2.5
LA0A
LA0A
LA0B
LA0B
LA6A
LA6A
LA6B
LA6B
LA1A
LA1A
LA1B
LA1B
LA2A
LA2A
1000 Units on Tape and Reel
3500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
STD
STD
A
LP2989IMMX-2.5
LP2989AIMM-2.8
LP2989AIMMX-2.8
LP2989IMM-2.8
A
STD
STD
A
LP2989IMMX-2.8
LP2989AIMM-3.0
LP2989AIMMX-3.0
LP2989IMM-3.0
A
STD
STD
A
LP2989IMMX-3.0
LP2989AIMM-3.3
LP2989AIMMX-3.3
A
3
www.national.com
Ordering Information (Continued)
TABLE 1. Package Marking and Ordering Information (Continued)
Output Voltage
Grade
STD
STD
A
Order Information
LP2989IMM-3.3
LP2989IMMX-3.3
LP2989AIMM-5.0
LP2989AIMMX-5.0
LP2989IMM-5.0
LP2989IMMX-5.0
Package Marking
LA2B
Supplied as:
3.3
3.3
5.0
5.0
5.0
5.0
1000 Units on Tape and Reel
3500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
1000 Units on Tape and Reel
3500 Units on Tape and Reel
LA2B
LA4A
A
LA4A
STD
STD
LA4B
LA4B
SO-8 (M)
2.5
2.5
2.5
2.5
3.0
3.0
3.0
3.0
3.3
3.3
3.3
3.3
5.0
5.0
5.0
5.0
A
A
LP2989AIMX-2.5
LP2989AIM-2.5
LP2989IMX-2.5
LP2989IM-2.5
LP2989AIM2.5
LP2989AIM2.5
LP2989IM2.5
LP2989IM2.5
LP2989AIM3.0
LP2989AIM3.0
LP2989IM3.0
LP2989IM3.0
LP2989AIM3.3
LP2989AIM3.3
LP2989IM3.3
LP2989IM3.3
LP2989AIM5.0
LP2989AIM5.0
LP2989IM5.0
LP2989IM5.0
2500 Units on Tape and Reel
Shipped in Anti-Static Rails
2500 Units on Tape and Reel
Shipped in Anti-Static Rails
2500 Units on Tape and Reel
Shipped in Anti-Static Rails
2500 Units on Tape and Reel
Shipped in Anti-Static Rails
2500 Units on Tape and Reel
Shipped in Anti-Static Rails
2500 Units on Tape and Reel
Shipped in Anti-Static Rails
2500 Units on Tape and Reel
Shipped in Anti-Static Rails
2500 Units on Tape and Reel
Shipped in Anti-Static Rails
STD
STD
A
LP2989AIMX-3.0
LP2989AIM-3.0
LP2989IMX-3.0
LP2989IM-3.0
A
STD
STD
A
LP2989AIMX-3.3
LP2989AIM-3.3
LP2989IMX-3.3
LP2989IM-3.3
A
STD
STD
A
LP2989AIMX-5.0
LP2989AIM-5.0
LP2989IMX-5.0
LP2989IM-5.0
A
STD
STD
<
For output voltages 2V, see LP2989LV datasheet.
www.national.com
4
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Input Supply Voltage (Survival)
Input Supply Voltage
(Operating)
−0.3V to +16V
2.1V to +16V
−0.3V to +6V
Sense Pin
Storage Temperature Range
Operating Junction Temperature
Range
−65˚C to +150˚C
Output Voltage (Survival)
(Note 4)
−0.3V to +16V
Short Circuit
Protected
−40˚C to +125˚C
IOUT (Survival)
Lead Temperature (Soldering, 5
seconds)
260˚C
2 kV
Input-Output Voltage (Survival)
(Note 5)
ESD Rating (Note 2)
Power Dissipation (Note 3)
−0.3V to +16V
Internally Limited
Electrical Characteristics
Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range. Un-
less otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 4.7 µF, CIN = 2.2 µF, VS/D = 2V.
LP2989AI-X.X
LP2989I-X.X
(Note 6)
(Note 6)
Symbol
VO
Parameter
Output Voltage
Conditions
Typical
Units
Min
−0.75
−1.5
Max
0.75
1.5
Min
−1.25
−2.5
Max
1.25
2.5
Tolerance
<
<
1 mA IL 500 mA
VO(NOM) + 1V ≤ VIN
16V
≤
≤
≤
−4.0
−3.5
2.5
2.5
−5.0
−4.5
3.5
3.5
%VNOM
<
<
1 mA IL 500 mA
VO(NOM) + 1V ≤ VIN
16V
−25˚C ≤ TJ ≤ 125˚C
VO(NOM) + 1V ≤ VIN
16V
Output Voltage Line
Regulation
0.014
0.014
0.005
0.4
%/V
0.032
0.032
<
<
Load Regulation
1 mA IL 500 mA
%VNOM
VIN–VO
Dropout Voltage
(Note 7)
IL = 100 µA
IL = 200 mA
IL = 500 mA
IL = 100 µA
IL = 200 mA
IL = 500 mA
3
4
3
4
1
150
310
110
1
200
300
425
650
175
200
2
200
300
425
650
175
200
2
mV
IGND
Ground Pin Current
µA
3.5
6
3.5
6
mA
3
9
9
<
VS/D 0.18V
0.5
0.05
800
2
2
µA
<
VS/D 0.4V
0.8
0.8
IO(PK)
Peak Output Current
Short Circuit Current
VOUT ≥ VO(NOM) − 5%
RL = 0 (Steady State)
(Note 9)
600
600
mA
IO(MAX)
1000
en
Output Noise Voltage
(RMS)
BW = 100 Hz to
100 kHz, COUT = 10 µF
CBYPASS = .01 µF
VOUT = 2.5V
18
µV(RMS)
5
www.national.com
Electrical Characteristics (Continued)
Limits in standard typeface are for TJ = 25˚C, and limits in boldface type apply over the full operating temperature range. Un-
less otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 4.7 µF, CIN = 2.2 µF, VS/D = 2V.
LP2989AI-X.X
LP2989I-X.X
(Note 6)
(Note 6)
Symbol
Parameter
Conditions
Typical
Units
Min
Max
Min
Max
Ripple Rejection
f = 1 kHz, COUT = 10 µF
60
dB
Output Voltage
(Note 8)
20
ppm/˚C
Temperature Coefficient
SHUTDOWN INPUT
VS/D S/D Input Voltage
VH = O/P ON
VL = O/P OFF
IIN ≤ 2 µA
1.4
1.6
1.6
V
0.18
0.18
0.50
IS/D
S/D Input Current
VS/D = 0
0.001
5
−1
15
−1
15
µA
VS/D = 5V
ERROR COMPARATOR
IOH
Output “HIGH” Leakage
VOH = 16V
1
1
0.001
150
µA
2
2
VOL
Output “LOW” Voltage
Upper Threshold Voltage
Lower Threshold Voltage
Hysteresis
VIN = VO(NOM) − 0.5V,
IO(COMP) = 150 µA
220
350
−3.5
−2.5
−4.9
−3.0
220
350
−3.5
−2.5
−4.9
−3.0
mV
VTHR
−6.0
−8.3
−6.0
−8.3
−4.8
(MAX)
VTHR
(MIN)
−8.9
−8.9
%VOUT
−6.6
2.0
−13.0
−13.0
HYST
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the
device outside of its rated operating conditions.
Note 2: ESD testing was performed using Human Body Model, a 100 pF capacitor discharged through a 1.5 kΩ resistor.
Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, T (MAX), the junction-to-ambient thermal resistance, θ
,
J−A
J
and the ambient temperature, T . The maximum allowable power dissipation at any ambient temperature is calculated using:
A
The value of θ
for the SO-8 (M) package is 160˚C/W and the mini SO-8 (MM) package is 200˚C/W. The value θ
for the LLP (LD) package is specifically
J−A
J−A
dependent on PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the LLP
package, refer to Application Note AN-1187. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into
thermal shutdown.
Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2989 output must be diode-clamped to ground.
Note 5: The output PNP structure contains a diode between the V and V
terminals that is normally reverse-biased. Forcing the output above the input will turn
OUT
IN
on this diode and may induce a latch-up mode which can damage the part (see Application Hints).
Note 6: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National’s Average Outgoing Quality Level (AOQL).
Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1V differential.
Note 8: Temperature coefficient is defined as the maximum (worst-case) change divided by the total temperature range.
Note 9: See Typical Performance Characteristics curves.
www.national.com
6
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA, VOUT = 2.5V.
Dropout Characteristics
Dropout Voltage vs Temperature
10133920
10133921
GND Pin Current vs
Dropout Voltage vs Load Current
Temperature and Load
10133923
10133919
Ground Pin Current vs Load Current
Input Current vs VIN
10133925
10133922
7
www.national.com
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA, VOUT = 2.5V. (Continued)
Input Current vs VIN
Input Current vs VIN
10133905
10133906
Line Transient Response
Line Transient Response
10133915
10133916
Line Transient Response
Line Transient Response
10133911
10133926
www.national.com
8
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA, VOUT = 2.5V. (Continued)
Load Transient Response
Load Transient Response
10133917
10133918
Short Circuit Current
Short Circuit Current vs Temperature
10133934
10133932
Short Circuit Current
Short Circuit Current vs VOUT
10133935
10133933
9
www.national.com
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA, VOUT = 2.5V. (Continued)
Ripple Rejection
Ripple Rejection
Ripple Rejection
Ripple Rejection
Ripple Rejection
Ripple Rejection
10133939
10133941
10133943
10133940
10133942
10133944
www.national.com
10
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA, VOUT = 2.5V. (Continued)
Ripple Rejection
Ripple Rejection In Dropout
10133946
10133945
Ripple Rejection vs Load
Output Noise Density
10133936
10133947
Output Noise Density
Turn-ON Waveform
10133928
10133937
11
www.national.com
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA, VOUT = 2.5V. (Continued)
Turn-ON Waveform
Turn-ON Waveform
10133929
10133930
10133910
10133909
Turn-ON Waveform
IGND vs Shutdown
10133931
IGND vs Shutdown
IGND vs Shutdown
10133908
www.national.com
12
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA, VOUT = 2.5V. (Continued)
IGND vs Shutdown
VOUT vs Shutdown
10133907
10133924
Typical Temperature vs VOUT (LP2989-2.5)
10133955
13
www.national.com
Application Hints
LLP PACKAGE DEVICES
The LP2989 is offered in the 8 lead LLP surface mount
package to allow for increased power dissipation compared
to the SO-8 and Mini SO-8. For details on thermal perfor-
mance as well as mounting and soldering specifications,
refer to Application Note AN-1187.
<
For output voltages 2V, see LP2989LV datasheet.
EXTERNAL CAPACITORS
Like any low-dropout regulator, the LP2989 requires external
capacitors for regulator stability. These capacitors must be
correctly selected for good performance.
Input Capacitor
An input capacitor whose size is at least 2.2 µF is required
between the LP2989 input and ground (the amount of ca-
pacitance may be increased without limit).
10133938
Stable Region For output Capacitor ESR
Characterization testing performed on the LP2989 has
shown that if the amount of actual input capacitance drops
below about 1.5 µF, an unstable operating condition may
result. Therefore, the next larger standard size (2.2 µF) is
specified as the minimum required input capacitance. Ca-
pacitor tolerance and temperature variation must be consid-
ered when selecting a capacitor (see Capacitor Character-
istics section) to assure the minimum requirement of 1.5 µF
is met over all operating conditions.
Important: The output capacitor must maintain its ESR
within the stable region over the full operating temperature
range of the application to assure stability.
It is important to remember that capacitor tolerance and
variation with temperature must be taken into consideration
when selecting an output capacitor so that the minimum
required amount of output capacitance is provided over the
full operating temperature range. (See Capacitor Character-
istics section).
The input capacitor must be located at a distance of not
more than 0.5" from the input pin and returned to a clean
analog ground. Any good quality ceramic or tantalum may be
used for this capacitor, assuming the minimum capacitance
requirement is met.
The output capacitor must be located not more than 0.5"
from the output pin and returned to a clean analog ground.
Noise Bypass Capacitor
Connecting a 10 nF capacitor to the Bypass pin significantly
reduces noise on the regulator output. However, the capaci-
tor is connected directly to a high-impedance circuit in the
bandgap reference.
Output Capacitor
The LP2989 requires a ceramic output capacitor whose size
is at least 4.7µF. The actual amount of capacitance on the
output must never drop below about 3.5µF or unstable op-
eration may result. For this reason, capacitance tolerance
and temperature characteristics must be considered when
selecting an output capacitor.
Because this circuit has only a few microamperes flowing in
it, any significant loading on this node will cause a change in
the regulated output voltage. For this reason, DC leakage
current through the noise bypass capacitor must never ex-
ceed 100 nA, and should be kept as low as possible for best
output voltage accuracy.
The LP2989 is designed specifically to work with ceramic
output capacitors, utilizing circuitry which allows the regula-
tor to be stable across the entire range of output current with
an output capacitor whose ESR is as low as 4 mΩ. It may
also be possible to use Tantalum or film capacitors at the
output, but these are not as attractive for reasons of size and
cost (see next section Capacitor Characteristics).
The types of capacitors best suited for the noise bypass
capacitor are ceramic and film. High-quality ceramic capaci-
tors with either NPO or COG dielectric typically have very
low leakage. 10 nF polypropolene and polycarbonate film
capacitors are available in small surface-mount packages
and typically have extremely low leakage current.
The output capacitor must meet the requirement for mini-
mum amount of capacitance and also have an ESR (equiva-
lent series resistance) value which is within the stable range.
Curves are provided which show the stable ESR range as a
function of load current (see ESR graph below).
CAPACITOR CHARACTERISTICS
Ceramic
The LP2989 was designed to work with ceramic capacitors
on the output to take advantage of the benefits they offer: for
capacitance values in the 4.7 µF range, ceramics are the
least expensive and also have the lowest ESR values (which
makes them best for eliminating high-frequency noise). The
ESR of a typical 4.7 µF ceramic capacitor is in the range of
10 mΩ to 15 mΩ, which easily meets the ESR limits required
for stability by the LP2989.
One disadvantage of ceramic capacitors is that their capaci-
tance can vary with temperature. Many large value ceramic
capacitors (≥ 2.2 µF) are manufactured with the Z5U or Y5V
www.national.com
14
However, their low leakage makes them a good choice for
the noise bypass capacitor. Since the required amount of
capacitance is only .01 µF, small surface-mount film capaci-
tors are available in this size.
Application Hints (Continued)
temperature characteristic, which results in the capacitance
dropping by more than 50% as the temperature goes from
25˚C to 85˚C.
SHUTDOWN INPUT OPERATION
This could cause problems if a 4.7 µF capacitor were used
on the output since it will drop down to approximately 2.4 µF
at high ambient temperatures (which could cause the
LP2989 to oscillate). Another significant problem with Z5U
and Y5V dielectric devices is that the capacitance drops
severely with applied voltage. A typical Z5U or Y5V capacitor
can lose 60% of its rated capacitance with half of the rated
voltage applied to it.
The LP2989 is shut off by driving the Shutdown input low,
and turned on by pulling it high. If this feature is not to be
used, the Shutdown input should be tied to VIN to keep the
regulator output on at all times.
To assure proper operation, the signal source used to drive
the Shutdown input must be able to swing above and below
the specified turn-on/turn-off voltage thresholds listed in the
Electrical Characteristics section under VON/OFF
.
For these reasons, X7R and X5R type ceramic capaci-
tors must be used on the input and output of the LP2989
To prevent mis-operation, the turn-on (and turn-off) voltage
signals applied to the Shutdown input must have a slew rate
which is ≥ 40 mV/µs.
Tantalum
Tantalum capacitors are less desirable than ceramics for use
as output capacitors because they are typically more expen-
sive when comparing equivalent capacitance and voltage
ratings in the 1 µF to 4.7 µF range.
CAUTION: the regulator output voltage can not be guaran-
teed if a slow-moving AC (or DC) signal is applied that is in
the range between the specified turn-on and turn-off volt-
ages listed under the electrical specification VON/OFF (see
Electrical Characteristics).
Another important consideration is that Tantalum capacitors
have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a Tantalum
capacitor with an ESR value within the stable range, it would
have to be larger in capacitance (which means bigger and
more costly) than a ceramic capacitor with the same ESR
value.
REVERSE INPUT-OUTPUT VOLTAGE
The PNP power transistor used as the pass element in the
LP2989 has an inherent diode connected between the regu-
lator output and input.
During normal operation (where the input voltage is higher
than the output) this diode is reverse-biased.
It should also be noted that the ESR of a typical Tantalum will
increase about 2:1 as the temperature goes from 25˚C down
to −40˚C, so some guard band must be allowed.
However, if the output is pulled above the input, this diode
will turn ON and current will flow into the regulator output.
Tantalum capacitors may be used on the input as long as the
requirement for minimum capacitance is met.
In such cases, a parasitic SCR can latch which will allow a
high current to flow into VIN (and out the ground pin), which
can damage the part.
Film
In any application where the output may be pulled above the
input, an external Schottky diode must be connected from
VIN to VOUT (cathode on VIN, anode on VOUT), to limit the
reverse voltage across the LP2989 to 0.3V (see Absolute
Maximum Ratings).
Polycarbonate and polypropelene film capacitors have ex-
cellent electrical performance: their ESR is the lowest of the
three types listed, their capacitance is very stable with tem-
perature, and DC leakage current is extremely low.
One disadvantage is that film capacitors are larger in physi-
cal size than ceramic or tantalum which makes film a poor
choice for either input or output capacitors.
15
www.national.com
Physical Dimensions inches (millimeters)
unless otherwise noted
SO-8 Package
NS Package Number M08A
Mini SO-8 Package
NS Package Number MUA08A
www.national.com
16
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
8 Lead LLP Surface Mount PackagePackage
NS Package Number LDC08A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明