LP3981IMMX-2.83/NOPB [TI]
2.83 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO8;型号: | LP3981IMMX-2.83/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 2.83 V FIXED POSITIVE LDO REGULATOR, 0.2 V DROPOUT, PDSO8 光电二极管 |
文件: | 总12页 (文件大小:749K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
National Semiconductor is now part of
Texas Instruments.
Search http://www.ti.com/ for the latest technical
information and details on our current products and services.
April 2005
LP3981
Micropower, 300mA Ultra Low-Dropout CMOS Voltage
Regulator
n 60dB PSRR at 1kHz
n ≤1µA quiescent current when shut down
n Fast Turn-On time: 120 µs (typ.) with CBYPASS = 0.01uF
n 132mV typ dropout with 300mA load
General Description
The LP3981’s performance is optimized for battery powered
systems to deliver ultra low noise, extremely low dropout
voltage and low quiescent current. Regulator ground current
n 35µVrms output noise over 10Hz to 100kHz
n −40 to +125˚C junction temperature range for operation
n 2.5V, 2.7V, 2.8V, 2.83V, 3.0V, 3.03V, and 3.3V outputs
standard
increases only slightly in dropout, further prolonging the
battery life.
Power supply rejection is better than 60 dB at low frequen-
cies. This high power supply rejection is maintained down to
lower input voltage levels common to battery operated cir-
cuits.
Features
The device is ideal for mobile phone and similar battery
powered wireless applications. It provides up to 300 mA,
from a 2.5V to 6V input, consuming less than 1µA in disable
mode.
n Small, space saving MSOP-8
n Low Thermal Resistance in LLP-6 package gives
excellent power capability
n Logic controlled enable
The LP3981 is available in MSOP-8 package. For LP3981 in
LLP-6 package, contact NSC sales offices. Performance is
specified for −40˚C to +125˚C temperature range. The de-
vice available in the following output voltages; 2.5V, 2.7V,
2.8V, 2.83V, 3.0V, 3.03V and 3.3V as standard. Other output
options can be made available, please contact your local
NSC sales office.
n Stable with ceramic and high quality tantalum capacitors
n Fast turn-on
n Thermal shutdown and short-circuit current limit
Applications
n CDMA cellular handsets
n Wideband CDMA cellular handsets
n GSM cellular handsets
n Portable information appliances
n Tiny 3.3V 5% to 2.5V, 300mA converter
Key Specifications
n 2.5 to 6.0V input range
n 300mA guaranteed output
Typical Application Circuit
20020302
Note: Pin Numbers in parenthesis indicate LLP-6 package.
© 2005 National Semiconductor Corporation
DS200203
www.national.com
Block Diagram
20020301
Pin Descriptions
Name
VEN
MSOP-8
LLP-6
Function
7
5
1
2
6
6
4
1
2
5
Enable Input Logic, Enable High.
Common Ground. Connect to PAD.
Output Voltage of the LDO.
Input Voltage of the LDO.
Optional bypass capacitor for noise
reduction.
GND
VOUT
VIN
Bypass
VOUT-SENSE
4
3
Output. Voltage Sense Pin. Should
be connected to VOUT for proper
operation.
N.C
3, 8
GND
PAD
Common Ground. Connect to pin 4.
Connection Diagrams
LLP-6 Package
MSOP-8 Package
20020307
20020370
Top View
Top View
See NS Package Number MUA008AE
See NS Package Number LDC06D
www.national.com
2
Ordering Information
For LLP-6 Package
Output
Grade
LP3981 Supplied as 1000
LP3981 Supplied as 4500
Units, Tape and Reel
LP3981ILDX-2.5
Package Marking
Voltage (V)
Units, Tape and Reel
LP3981ILD-2.5
LP3981ILD-2.7
LP3981ILD-2.8
LP3981ILD-2.83
LP3981ILD-3.0
LP3981ILD-3.03
LP3981ILD -3.3
2.5
2.7
STD
STD
STD
STD
STD
STD
STD
LO1UB
LO1VB
LO1ZB
L01SB
L017B
LO1YB
LO1XB
LP3981ILDX-2.7
2.8
LP3981ILDX-2.8
2.83
3.0
LP3981ILDX-2.83
LP3981ILDX-3.0
3.03
3.3
LP3981ILDX-3.03
LP3981ILDX-3.3
For MSOP-8 Package
Output
Voltage (V)
2.5
LP3981 Supplied as 1000
Units, Tape and Reel
LP3981IMM-2.5
LP3981 Supplied as 3500
Units, Tape and Reel
LP3981IMMX-2.5
Grade
Package Marking
STD
STD
STD
STD
STD
STD
STD
LFKB
LFLB
LFTB
LDUB
LF3B
LFPB
LFNB
2.7
LP3981IMM-2.7
LP3981IMMX-2.7
2.8
LP3981IMM-2.8
LP3981IMMX-2.8
2.83
LP3981IMM-2.83
LP3981IMM-3.0
LP3981IMMX-2.83
LP3981IMMX-3.0
3.0
3.03
LP3981IMM-3.03
LP3981IMMX-3.03
LP3981IMMX-3.3
3.3
LP3981IMM-3.3
*
Please contact factory regarding the availability of voltage options not listed here.
3
www.national.com
Absolute Maximum Ratings (Notes 1, 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
ESD Rating(Note 4)
Human Body Model
Machine Model
2kV
200V
VIN, VEN
OUT, VOUT-SENSE
−0.3 to 6.5V
−0.3 to VIN + 0.3,
Max 6.5V
Operating Ratings (Notes 1, 2)
VIN
V
2.7 to 6V
0 to VIN
VEN
Junction Temperature
Storage Temperature
Lead Temp.
150˚C
Junction Temperature
−40˚C to +125˚C
−65˚C to +150˚C
Maximum Power Dissipation (Note 5)
MSOP-8
LLP-6
476mW
2.0W
Pad Temp.
Power Dissipation (Note 3)
θJA (MSOP-8)
θJA (LLP-6)
210˚C/W
50˚C/W
Maximum Power Dissipation at 25˚C
MSOP-8
595mW
2.5W
LLP-6
Electrical Characteristics
Unless otherwise specified: VEN = 1.2V, VIN = VOUT + 0.5V, CIN = 2.2 µF, CBP = 0.033 µF, IOUT = 1mA, COUT = 2.2 µF. Typi-
cal values and imits appearing in standard typeface are for TJ = 25˚C. Limits appearing in boldface type apply over the entire
junction temperature range for operation, −40˚C to +125˚C. (Notes 6, 7)
Limit
Symbol
Parameter
Output Voltage
Conditions
Typ
Units
Min
−2
Max
2
% of
Tolerance
−3
3
VOUT(nom)
<
VIN = VOUT + 0.5V to 6.0V, TA
+85˚C
0.005
−0.1
0.1
%/V
∆VOUT
Line Regulation Error
VIN = VOUT + 0.5V to 6.0V, TJ ≤125˚C
−0.2
0.2
%/V
Load Regulation Error
(Note 8)
IOUT = 1 mA to 300 mA
0.0003
50
0.005 %/mA
VIN = VOUT(nom) + 1V,
f = 1 kHz,
IOUT = 50 mA (Figure 2)
VIN = VOUT(nom) + 1V,
f = 10 kHz,
Power Supply Rejection Ratio
(Note 10)
PSRR
dB
55
IOUT = 50 mA (Figure 2)
VEN = 1.2V, IOUT = 1 mA
VEN = 1.2V, IOUT = 1 to 300 mA,
VOUT = 2.5V(Note 12)
VEN = 0.4V
IQ
Quiescent Current
70
120
170
210
µA
0.003
0.5
1.5
5
IOUT = 1 mA
Dropout Voltage (Note 9)
Short Circuit Current Limit
Output Noise Voltage
IOUT = 200 mA
88
133
200
mV
IOUT = 300 mA
132
600
ISC
en
Output Grounded
(Steady State)
mA
BW = 10 Hz to 100 kHz,
CBP = 0.033µF
35
µVrms
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Peak Output Current
160
20
˚C
˚C
TSD
IOUT(PK)
IEN
VOUT ≥ VOUT (nom) - 5%
VEN = 0 and VIN
455
300
Maximum Input Current at VEN
Logic Low Input threshold
0.001
µA
V
VIL
VIN = 2.7 to 6.0V
0.4
www.national.com
4
Electrical Characteristics (Continued)
Unless otherwise specified: VEN = 1.2V, VIN = VOUT + 0.5V, CIN = 2.2 µF, CBP = 0.033 µF, IOUT = 1mA, COUT = 2.2 µF. Typi-
cal values and imits appearing in standard typeface are for TJ = 25˚C. Limits appearing in boldface type apply over the entire
junction temperature range for operation, −40˚C to +125˚C. (Notes 6, 7)
Limit
Symbol
Parameter
Conditions
Typ
Units
Min
1.4
Max
350
VIH
TON
Logic High Input threshold
Turn-On Time
VIN = 2.7 to 6.0V
CBYPASS = 0.033 µF
V
µs
240
(Note 10) (Note 11)
Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device
is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical
Characteristics tables.
Note 2: All voltages are with respect to the potential at the GND pin.
Note 3: The figures given for Absolute Maximum Power disipation for the device are calculated using the following equations:
where T
is the maximum junction temperature, T is the ambient temperature, and θ
is the junction-to-ambient thermal resistance.
JA
J(MAX)
A
E.g. for the LLP package θ =50˚C/W, T
=150˚C and using T =25˚C the maximum power dissipation is found to be 2.5W. The derating factor (−1/θ ) =
A JA
JA
J(MAX)
−20mW/˚C, thus below 25˚C the power dissipation figure can be increased by 20W per degree, and similarity decreased by this factor for temperatures above 25˚C
Note 4: The human body model is 100pF discharged through 1.5kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each
pin.
Note 5: As for the Maximum Power dissipation, the maximum power in operation is dependant on the ambient temperature. This can be calculated in teh same way
using T =125˚C, giving 2W as the maximum power dissipation for the LLP package in operation. The same derating factor applies.
J
Note 6: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production with T = 25˚C or correlated using
J
Statistical Quality Control (SQC) methods. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations
and applying statistical process control.
Note 7: The target output voltage, which is labeled V
, is the desired voltage option.
OUT(nom)
Note 8: An increase in the load current results in a slight decrease in the output voltage and vice versa.
Note 9: Dropout voltage is the input-to-output voltage difference at which the output voltage is 100mV below its nominal value. This specification does not apply for
input voltages below 2.5V.
Note 10: Guaranteed by design.
Note 11: Turn-on time is time measured between the enable input just exceeding V and the output voltage just reaching 95% of its nominal value.
IH
>
Note 12: For V
2.5C, Increase I
by 2.5µA for every 0.1V increase in V
.
OUT(NOM)
OUT
Q(MAX)
i.e. I
= 210 + ((V
- 2.5) * 25)µA
OUT(NOM)
Q(MAX)
Output Capacitor, Recommended Specification
Limit
Symbol
Parameter
Conditions
Typ
Units
Min
2.2
Max
COUT
Output Capacitor
Capacitance
ESR
22
µF
5
500
mΩ
20020308
FIGURE 1. Line Transient Response Input Perturbation
5
www.national.com
20020309
FIGURE 2. PSRR Input Perturbation
Typical Performance Characteristics Unless otherwise specified, CIN = COUT = 2.2 µF Ceramic,
CBP = 0.033 µF, VIN = VOUT + 0.5V, TA = 25˚C, Enable pin is tied to VIN
.
Output Voltage vs. Temperature (VOUT = 2.83V)
Dropout Voltage vs. Temperature (VOUT = 2.85V)
20020317
20020318
Ground Current vs. Load Current (VOUT = 2.85V)
Output Short Circuit Current
20020320
20020319
www.national.com
6
Typical Performance Characteristics Unless otherwise specified, CIN = COUT = 2.2 µF Ceramic,
CBP = 0.033 µF, VIN = VOUT + 0.5V, TA = 25˚C, Enable pin is tied to VIN. (Continued)
Output Short Circuit Current
Ripple Rejection (VIN = VOUT + 1V)
20020332
20020321
Ripple Rejection (VIN = VOUT + 1V)
Ripple Rejection (VIN = VOUT + 1V)
20020322
20020323
Load Transient Response (VIN = 3.5V)
Load Transient Response (VIN = 3.5V)
20020324
20020325
7
www.national.com
Typical Performance Characteristics Unless otherwise specified, CIN = COUT = 2.2 µF Ceramic,
CBP = 0.033 µF, VIN = VOUT + 0.5V, TA = 25˚C, Enable pin is tied to VIN. (Continued)
Line Transient Response
Line Transient Response
(VIN = VOUT + 1V to VOUT + 1.6V)
(VIN = VOUT + 1V to VOUT + 1.6V)
20020326
20020327
Line Transient Response
Line Transient Response
(VIN = VOUT + 1V to VOUT + 1.6V)
(VIN = VOUT + 1V to VOUT + 1.6V)
20020328
20020329
Enable Response (TON
)
Enable Response (TON)
20020330
20020331
As stated in notes 3 and 5 in the electrical specifications
sections, the allowable power dissipation for the device in a
given package can be calculated using the equation:
Application Hints
POWER DISSIPATION AND DEVICE OPERATION
The permissible power dissipation for any package is a
measure of the capability of the device to pass heat from the
power source, the junctions of the IC, to the ultimate heat
sink, the ambient environment. Thus, the power dissipation
is dependant on the ambient temperature and the thermal
resistance across the various interfaces between the die and
ambient air.
With a θJA = 50˚C/W, the device in theLLP package returns
a value of 2.0W with a maximum junction temperature of
www.national.com
8
NOISE BYPASS CAPACITOR
Application Hints (Continued)
Connecting a 0.033µF capacitor between the CBP pin and
ground significantly reduces noise on the regulator output.
This cap is connected directly to a high impedance node in
the bad gap reference circuit. Any significant loading on this
node will cause a change on the regulated output voltage.
For this reason, DC leakage current through this pin must be
kept as low as possible for best output voltage accuracy.
125˚C and an ambient temperature of 25˚C. The device in a
MSOP package returns a figure of 0.476W, ( θJA = 210˚C/
W).
The actual power dissipation across the device can be rep-
resented by the following equation:
PD = (VIN − VOUT) x IOUT
The types of capacitors best suited for the noise bypass
capacitor are ceramic and film. Hight-quality ceramic capaci-
tors with either NPO or COG dielectric typically have very
low leakage. Polypropolene and polycarbonate film capaci-
tors are available in small surface-mount packages and
typically have extremely low leakage current.
This establishes the relationship between the power dissipa-
tion allowed due to thermal considerations, the voltage drop
across the device, and the continuous current capability of
the device. The device can deliver 300mA but care must be
taken when choosing the continuous current output for the
device under the operating load conditions.
Unlike many other LDO’s, addition of a noise reduction
capacitor does not effect the transient response of the de-
vice.
EXTERNAL CAPACITORS
Like any low-dropout regulator, the LP3981 requires external
capacitors for regulator stability. The LP3981 is specifically
designed for portable applications requiring minimum board
space and smallest components. These capacitors must be
correctly selected for good performance.
CAPACITOR CHARACTERISTICS
The LP3981 is designed to work with ceramic capacitors on
the output to take advantage of the benefits they offer: for
capacitance values in the range of 1µF to 4.7µF range,
ceramic capacitors are the smallest, least expensive and
have the lowest ESR values (which makes them best for
eliminating high frequency noise). The ESR of a typical 1µF
ceramic capacitor is in the range of 20 mΩ to 40 mΩ, which
easily meets the ESR requirement for stability by the
LP3981.
INPUT CAPACITOR
An input capacitance of ) 2.2µF is required between the
LP3981 input pin and ground (the amount of the capacitance
may be increased without limit).
This capacitor must be located a distance of not more than
1cm from the input pin and returned to a clean analog
ground. Any good quality ceramic, tantalum, or film capacitor
may be used at the input.
The ceramic capacitor’s capacitance can vary with tempera-
ture. Most large value ceramic capacitors () 2.2µF) are
manufactured with Z5U or Y5V temperature characteristics,
which results in the capacitance dropping by more than 50%
as the temperature goes from 25˚C to 85˚C.
Important: Tantalum capacitors can suffer catastrophic fail-
ures due to surge current when connected to a low-
impedance source of power (like a battery or a very large
capacitor). If a tantalum capacitor is used at the input, it must
be guaranteed by the manufacturer to have a surge current
rating sufficient for the application.
A better choice for temperature coefficient in a ceramic
capacitor is X7R, which holds the capacitance within 15%.
Tantalum capacitors are less desirable than ceramic for use
as output capacitors because they are more expensive when
comparing equivalent capacitance and voltage ratings in the
1µF to 4.7µF range.
There are no requirements for the ESR on the input capaci-
tor, but tolerance and temperature coefficient must be con-
sidered when selecting the capacitor to ensure the capaci-
tance will be ) 2.2µF over the entire operating temperature
range.
Another important consideration is that tantalum capacitors
have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a tantalum
capacitor with an ESR value within the stable range, it would
have to be larger in capacitance (which means bigger and
more costly ) than a ceramic capacitor with the same ESR
value. It should also be noted that the ESR of a typical
tantalum will increase about 2:1 as the temperature goes
from 25˚C down to −40˚C, so some guard band must be
allowed.
OUTPUT CAPACITOR
The LP3981 is designed specifically to work with very small
ceramic output capacitors. A ceramic capacitor (dielectric
types Z5U, Y5V or X7R) in 2.2 to 22 µF range with 5mΩ to
500mΩ ESR range is suitable in the LP3981 application
circuit.
It may also be possible to use tantalum or film capacitors at
the output, but these are not as attractive for reasons of size
and cost (see next section Capacitor Characteristics).
ON/OFF INPUT OPERATION
The LP3981 is turned off by pulling the VEN pin low, and
turned on by pulling it high. If this feature is not used, the VEN
pin should be tied to VIN to keep the regulator output on at all
time. To assure proper operation, the signal source used to
drive the VEN input must be able to swing above and below
the specified turn-on/off voltage thresholds listed in the Elec-
The output capacitor must meet the requirement for mini-
mum amount of capacitance and also have an ESR (Equiva-
lent Series Resistance) value which is within a stable range
(5 mΩ to 500 mΩ).
NO-LOAD STABILITY
trical Characteristics section under VIL and VIH
.
The LP3981 will remain stable and in regulation with no
external load. This is specially important in CMOS RAM
keep-alive applications.
FAST ON-TIME
The LP3981 utilizes a speed up circuitry to ramp up the
internal VREF voltage to its final value to achieve a fast
output turn on time.
9
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted
NS Package Number MUA008AE
NS Package Number LDC06D
www.national.com
10
Notes
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
National Semiconductor
Asia Pacific Customer
Support Center
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明