LP5907UVX37/NOPB [TI]
具有低 IQ 和使能功能的 250mA、低噪声、高 PSRR、超低压降稳压器 | YKE | 4 | -40 to 125;型号: | LP5907UVX37/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有低 IQ 和使能功能的 250mA、低噪声、高 PSRR、超低压降稳压器 | YKE | 4 | -40 to 125 电源电路 线性稳压器IC |
文件: | 总13页 (文件大小:774K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
May 9, 2012
LP5907
Ultra Low-Noise, 250 mA Linear Regulator for RF/Analog
Circuits - Requires No Bypass Capacitor
General Description
Key Specifications
The LP5907 is a linear regulator capable of supplying 250 mA
output current. Designed to meet the requirements of RF/
Analog circuits, the LP5907 device provides low noise, high
PSRR, low quiescent current, and low line/load transient re-
sponse figures. Using new innovative design techniques the
LP5907 offers class-leading noise performance without a
noise bypass capacitor and the ability for remote output ca-
pacitor placement.
Input voltage range
2.2V to 5.5V
1.2V to 4.5V
250 mA
■
Output voltage range
Output current
Low output voltage noise
PSRR
Output voltage tolerance
Virtually zero IQ (disabled)
Very low IQ (enabled)
Startup time
■
■
<10 μVRMS
82 dB at 1kHz
± 2%
■
■
■
<1μA
12 μA
80 μs
120 mV typ.
■
■
The device is designed to work with a 1.0 μF input and a
1.0 μF output ceramic capacitor. (No Bypass Capacitor is re-
quired.)
■
Low dropout
■
The device is available in an ultra-thin micro SMD package.
This device is available between 1.2V and 4.5V in 25 mV
steps. Please contact Texas Instruments Sales for specific
voltage option needs.
Package
4-Bump ultra-thin micro SMD
0.35 mm pitch
0.65 mm x 0.65 mm x
0.40 mm
(lead free)
Features
Stable with 1.0 μF Ceramic Input and Output Capacitors
No Noise Bypass Capacitor Required
■
■
■
■
■
Applications
Cellular phones
■
■
■
Remote Output Capacitor Placement
PDA handsets
Thermal-overload and short-circuit protection
−40°C to +125°C junction temperature range for operation
Wireless LAN devices
Typical Application Circuit
30180501
© 2012 Texas Instruments Incorporated
301805 SNVS798B
www.ti.com
Connection Diagrams
4-Bump Ultra-Thin micro SMD Package
Package Number UVK04AAA
30180502
The actual physical placement of the package marking will vary from part to part.
Pin Descriptions
micro SMD
Symbol
Name and Function
Pin No.
A1
A2
VIN
Input voltage supply. A 1.0 µF capacitor should be connected at this input.
VOUT
Output voltage. A 1.0 μF Low ESR capacitor should be connected to this pin. Connect
this output to the load circuit. An internal 280Ω discharge resistor prevents a charge
remaining on VOUT when disabled, only active when EN = high.
B1
B2
VEN
GND
Enable input; disables the regulator when ≤ 0.4V. Enables the regulator when ≥ 1.2V.
An internal 1MΩ pulldown resistor connects this input to ground.
Common ground.
Ordering Information
micro SMD Package (Lead Free)
Output Voltage (V)
Supplied As
250 tape and reel
3000 tape and reel
LP5907UVX-1.2/NOPB
LP5907UVX-1.8/NOPB
LP5907UVX-2.7/NOPB
LP5907UVX-2.8/NOPB
LP5907UVX-2.85/NOPB
LP5907UVX-3.0/NOPB
LP5907UVX-3.1/NOPB
LP5907UVX-3.2/NOPB
LP5907UVX-3.3/NOPB
LP5907UVX-4.5/NOPB
1.2
1.8
2.7
2.8
2.85
3.0
3.1
3.2
3.3
4.5
LP5907UVE-1.2/NOPB
LP5907UVE-1.8/NOPB
LP5907UVE-2.7/NOPB
LP5907UVE-2.8/NOPB
LP5907UVE-2.85/NOPB
LP5907UVE-3.0/NOPB
LP5907UVE-3.1/NOPB
LP5907UVE-3.2/NOPB
LP5907UVE-3.3/NOPB
LP5907UVE-4.5/NOPB
Contact your local TI Sales Office for availability of other voltage options.
www.ti.com
2
Absolute Maximum Ratings (Note 1, Note
2)
Operating Ratings (Note 1, Note 2)
VIN: Input Voltage Range
2.2V to 5.5V
VEN: Enable Voltage Range
0 to (VIN + 0.3V) to
5.5V (max)
If Military/Aerospace specified devices are required,
please contact the Texas Instruments Sales Office/
Distributors for availability and specifications.
Recommended Load Current
0 to 250 mA
(Note 5)
VIN Pin: Input Voltage
−0.3 to 6.0V
−0.3 to (VIN + 0.3V) to 6.0V
(max)
Junction Temperature Range (TJ)
−40°C to +125°C
−40°C to +85°C
VOUT Pin: Output Voltage
Ambient Temperature Range (TA)
(Note 5)
VEN Pin: Enable Input Voltage −0.3 to (VIN + 0.3V) to 6.0V
(max)
Thermal Properties
Continuous Power Dissipation
(Note 3)
Junction Temperature (TJMAX
Internally Limited
150°C
Junction-to-Ambient Thermal Resistance θJA (Note 6)
)
JEDEC Board (micro SMD)
119.6°C/W
186.5°C/W
(Note 16)
Storage Temperature Range
Maximum Lead Temperature
(Soldering, 10 sec.)
−65 to 150°C
4L Cellphone Board (micro SMD)
260°C
ESD Rating (Note 4)
Human Body Model
Machine Model
2kV
200V
Electrical Characteristics
Limits in standard typeface are for TA = 25ºC. Limits in boldface type apply over the full operating junction temperature range
(−40ºC ≤ TJ ≤ +125°C). Unless otherwise noted, specifications apply to the LP5907 Typical Application Circuit (pg. 1) with: VIN
VOUT (NOM) + 1.0V, VEN = 1.2V, CIN = 1.0 μF, COUT = 1.0 μF, IOUT = 1.0 mA. (Note 2, Note 7)
=
Symbol
VIN
Parameter
Input Voltage
Conditions
Min
Typ
Max
Units
2.2
5.5
V
VIN = (VOUT(NOM) + 1.0V) to 5.5V,
IOUT = 1mA to 250 mA
Output Voltage Tolerance
Line Regulation
−2
2
%
VIN = (VOUT(NOM) + 1.0V) to 5.5V,
IOUT = 1 mA
ΔVOUT
0.02
%/V
%/mA
mA
IOUT = 1mA to 250 mA
Load Regulation
0.001
Load Current
(Note 9)
ILOAD
Maximum Output Current
250
VEN = 1.2V, IOUT = 0 mA
VEN = 1.2V, IOUT = 250 mA
VEN = 0.3V (Disabled)
IOUT = 0 mA (VEN = 1.2V)
VOUT = 2.8V; IOUT = 100 mA
VOUT = 2.8V; IOUT = 250 mA
(Note 12)
12
250
0.2
14
25
425
1
IQ
Quiescent Current (Note 11)
µA
IG
Ground Current (Note 13)
Dropout Voltage (Note 10)
Short Circuit Current Limit
µA
mV
mA
50
VDO
ISC
120
500
90
200
250
f = 100 Hz, IOUT = 20 mA
f = 1 kHz, IOUT = 20 mA
f = 10 kHz, IOUT = 20 mA
f = 100 kHz, IOUT = 20 mA
82
Power Supply Rejection Ratio
(Note 15)
PSRR
dB
65
60
IOUT = 1 mA
10
eN
µVRMS
°C
Output Noise Voltage (Note 15) BW = 10 Hz to 100 kHz,
IOUT = 250 mA
6.5
160
15
Temperature
Thermal Shutdown
TSHUTDOWN
Hysteresis
3
www.ti.com
Symbol
Parameter
Conditions
VIN = 2.2V to 5.5V
Min
1.2
Typ
Max
0.4
Units
LOGIN INPUT THRESHOLDS
VIL
VIH
Low Input Threshold (VEN
)
V
V
High Input Threshold (VEN
)
VIN = 2.2V to 5.5V
VEN = 5.5V and VIN = 5.5V
VEN = 0.0V and VIN = 5.5V
5.5
Input Current at VEN Pin
IEN
μA
(Note 14)
0.001
TRANSIENT CHARACTERISTICS
VIN = (VOUT(NOM) + 1.0V) to (VOUT(NOM) +
-1
1.6V) in 30 μs, IOUT = 1mA
Line Transient
(Note 15)
mV
mV
VIN = (VOUT(NOM) + 1.6V) to (VOUT(NOM)
+
+1
1.0V) in 30 μs, IOUT = 1mA
ΔVOUT
IOUT = 1mA to 250 mA in 10 μs
IOUT = 250 mA to 1mA in 10 μs
−40
Load Transient
(Note 15)
40
5
Overshoot on Startup
(Note 15)
Stated as a percentage of nominal VOUT
To 95% of VOUT(NOM)
%
Turn on Time
80
150
μs
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation
of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions,
see the Electrical Characteristics tables.
Note 2: All voltages are with respect to the potential at the GND pin.
Note 3: Internal thermal shutdown circuitry protects the device from permanent damage.
Note 4: The Human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200 pF capacitor discharged
directly into each pin. MIL-STD-883 3015.7
Note 5: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be
derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125°C), the maximum power
dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the part/package in the application (θJA), as given by the
following equation: TA-MAX = TJ-MAX-OP – (θJA × PD-MAX). See applications section.
Note 6: Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high maximum power dissipation exists,
special care must be paid to thermal dissipation issues in board design.
Note 7: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm.
Note 8: CIN, COUT: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics.
Note 9: The device maintains a stable, regulated output voltage without a load current.
Note 10: Dropout voltage is the voltage difference between the input and the output at which the output voltage drops to 100 mV below its nominal value.
Note 11: Quiescent current is defined here as the difference in current between the input voltage source and the load at VOUT
.
Note 12: Short Circuit Current is measured with VOUT pulled to 0V and VIN worst case = 6.0V.
Note 13: Ground current is defined here as the total current flowing to ground as a result of all input voltages applied to the device.
Note 14: There is a 1MΩ resistor between VEN and ground on the device.
Note 15: This specification is guaranteed by design.
Note 16: Detailed description of the board can be found in JESD51-7.
Output & Input Capacitors
Symbol
CIN
Parameter
Conditions
Min
0.7
0.7
5
Nom
1.0
Max
Units
µF
Input Capacitance (Note 15)
Output Capacitance (Note 15)
Output/Input Capacitance (Note 15)
Capacitance for stability
COUT
ESR
1.0
10
500
mΩ
Note: The minimum capacitance should be > 0.5 µF over the full range of operating conditions. The capacitor tolerance should be 30% or better over the full
temperature range. The full range of operating conditions for the capacitor in the application should be considered during device selection to ensure this minimum
capacitance specification is met. X7R capacitors are recommended however capacitor types X5R, Y5V and Z5U may be used with consideration of the application
and conditions.
www.ti.com
4
Block Diagram
30180506
5
www.ti.com
Typical Performance Curves
Unless otherwise, VOUT = 2.8V, VIN = 3.7V, EN = 1.2V, CIN = 1.0µF, COUT = 1.0µF, TA = 25°C.
Iq vs. VIN
Ground Current vs. Output Current
350
300
250
200
150
100
50
16
14
12
10
8
6
4
VIN = 3.0V
VIN = 3.8V
VIN = 4.2V
VIN = 5.5V
2
0
0
0
50 100 150 200 250 300
2.3 2.8 3.3 3.8 4.3 4.8 5.3 5.8
(V)
I
(mA)
V
OUT
IN
30180571
30180569
Load Regulation
Line Regulation
2.900
2.875
2.850
2.825
2.800
2.775
2.750
2.725
2.700
2.900
2.875
2.850
2.825
2.800
2.775
2.750
2.725
2.700
V
= 3.6V
IN
Load = 10 mA
-40°C
90°C
25°C
-40°C
90°C
25°C
0
50
100
150
200
250
3.0
3.5
4.0
V
4.5
(V)
5.0
5.5
LOAD (mA)
IN
30180567
30180568
Inrush Current
Line Transient
VIN = 3.2V ↔ 4.2V, Load = 1mA
30180509
30180510
www.ti.com
6
Line Transient
Load Transient
VIN = 3.2V ↔ 4.2V, Load = 250mA
Load = 0mA ↔ 250mA, −40°C
30180511
30180512
Load Transient
Load Transient
Load = 0mA ↔ 250mA, 90°C
Load = 0mA ↔ 250mA, 25°C
30180514
30180513
Startup 0mA
Startup 250mA
30180516
30180515
7
www.ti.com
Noise Density Test
Dropout Voltage v. Load Current
140
10
1
120
100
80
60
40
20
0
1 mA Load
0.1
0.01
Dropout Voltage
100 mA Load
0 mA Load
0.001
1
100
10000
1000000 10000000
0
50
100
150
200
250
LOAD CURRENT (mA)
FREQUENCY (Hz)
30180573
30180518
PSRR Loads
Averaged 20Hz to 100kHz
30180507
PSRR Loads
Averaged 100Hz to 100kHz
30180508
www.ti.com
8
and with ESR between 5mΩ to 500 mΩ, is suitable in the
LP5907 application circuit. For this device the output capaci-
tor should be connected between the VOUT pin and a good
ground connection.
Application Hints
POWER DISSIPATION AND DEVICE OPERATION
The permissible power dissipation for any package is a mea-
sure of the capability of the device to pass heat from the power
source, the junctions of the IC, to the ultimate heat sink, the
ambient environment. Thus the power dissipation is depen-
dent on the ambient temperature and the thermal resistance
across the various interfaces between the die and ambient
air. As stated in (Note 5) of the electrical characteristics, the
allowable power dissipation for the device in a given package
can be calculated using the equation:
It may also be possible to use tantalum or film capacitors at
the device output, VOUT, but these are not as attractive for
reasons of size and cost (see CAPACITOR CHARACTERIS-
TICS below).
The output capacitor must meet the requirement for the min-
imum value of capacitance and have an ESR value that is
within the range 5mΩ to 500 mΩ for stability.
CAPACITOR CHARACTERISTICS
The LP5907 is designed to work with ceramic capacitors on
the input and output to take advantage of the benefits they
offer. For capacitance values in the range of 1.0 μF to 10 μF,
ceramic capacitors are the smallest, least expensive and
have the lowest ESR values, thus making them best for elim-
inating high frequency noise. The ESR of a typical 1.0 μF
ceramic capacitor is in the range of 20 mΩ to 40 mΩ, which
easily meets the ESR requirement for stability for the LP5907.
The actual power dissipation across the device can be rep-
resented by the following equation:
PD = (VIN – VOUT) x IOUT
This establishes the relationship between the power dissipa-
tion allowed due to thermal consideration, the voltage drop
across the device, and the continuous current capability of the
device. These two equations should be used to determine the
optimum operating conditions for the device in the application.
The temperature performance of ceramic capacitors varies by
type and manufacturer. Most large value ceramic capacitors
(≥2.2 µF) are manufactured with Z5U or Y5V temperature
characteristics, which results in the capacitance dropping by
more than 50% as the temperature goes from 25°C to 85°C.
EXTERNAL CAPACITORS
A better choice for temperature coefficient in a ceramic ca-
pacitor is X7R. This type of capacitor is the most stable and
holds the capacitance within ±15% over the temperature
range. Tantalum capacitors are less desirable than ceramic
for use as output capacitors because they are more expen-
sive when comparing equivalent capacitance and voltage
ratings in the 1.0 μF to 10 μF range.
Like any low-dropout regulator, the LP5907 requires external
capacitors for regulator stability. The LP5907 is specifically
designed for portable applications requiring minimum board
space and smallest components. These capacitors must be
correctly selected for good performance.
INPUT CAPACITOR
Another important consideration is that tantalum capacitors
have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a tantalum capac-
itor with an ESR value within the stable range, it would have
to be larger in capacitance (which means bigger and more
costly) than a ceramic capacitor with the same ESR value. It
should also be noted that the ESR of a typical tantalum will
increase about 2:1 as the temperature goes from 25°C down
to −40°C, so some guard band must be allowed.
An input capacitor is required for stability. The input capacitor
should be at least equal to, or greater than, the output capac-
itor for good load transient performance. At least a 1.0 µF
capacitor has to be connected between the LP5907 input pin
and ground for stable operation over full load current range.
Basically, it is ok to have more output capacitance than input,
as long as the input is at least 1.0 uF
This capacitor must be located a distance of not more than
1cm from the input pin and returned to a clean analog ground.
Any good quality ceramic, tantalum, or film capacitor may be
used at the input.
REMOTE CAPACITOR OPERATION
The LP5907 requires at least a 1μF capacitor at output pin,
but there is no strict requirements about the location of the
capacitor in regards the LDO output pin. In practical designs
the output capacitor may be located some 5-10 cm away from
the LDO. This means that there is no need to have a special
capacitor close to the output pin if there is already respective
capacitor(s) in the system (like a capacitor at the input of sup-
plied part). The Remote Capacitor feature helps user to min-
imize the number of capacitors in the system. As a good
design practice, it is good to keep the wiring parasitic induc-
tance at a minimum, which means to use as wide as possible
traces from the LDO output to the capacitor(s), keeping the
LDO trace layer as close as possible to ground layer and
avoiding vias on the path. If there is a need to use vias, im-
plement as many as possible vias between the connection
layers. The recommendation is to keep parasitic wiring in-
ductance less than 35 nH. For the applications with fast load
transients, it is recommended to use an input capacitor equal
to or larger to the sum of the capacitance at the output node
for the best load transient performance.
Important: To ensure stable operation it is essential that
good PCB practices are employed to minimize ground
impedance and keep input inductance low. If these conditions
cannot be met, or if long leads are to be used to connect the
battery or other power source to the LP5907, then it is rec-
ommended to increase the input capacitor to at least 10 µF.
Also, tantalum capacitors can suffer catastrophic failures due
to surge current when connected to a low-impedance source
of power (like a battery or a very large capacitor). If a tantalum
capacitor is used at the input, it must be guaranteed by the
manufacturer to have a surge current rating sufficient for the
application. There are no requirements for the ESR (Equiva-
lent Series Resistance) on the input capacitor, but tolerance
and temperature coefficient must be considered when select-
ing the capacitor to ensure the capacitance will remain
1.0 μF ±30% over the entire operating temperature range.
OUTPUT CAPACITOR
The LP5907 is designed specifically to work with a very small
ceramic output capacitor, typically 1.0 µF. A ceramic capaci-
tor (dielectric types X5R or X7R) in the 1.0 μF to 10 μF range,
9
www.ti.com
NO-LOAD STABILITY
For best results during assembly, alignment ordinals on the
PC board may be used to facilitate placement of the micro
SMD device.
The LP5907 will remain stable and in regulation with no ex-
ternal load.
MICRO SMD LIGHT SENSITIVITY
ENABLE CONTROL
Exposing the micro SMD device to direct light may cause in-
correct operation of the device. Light sources such as halogen
lamps can affect electrical performance if they are situated in
proximity to the device.
The LP5907 may be switched ON or OFF by a logic input at
the ENABLE pin. A high voltage at this pin will turn the device
on. When the enable pin is low, the regulator output is off and
the device typically consumes 3nA. However if the application
does not require the shutdown feature, the VEN pin can be tied
to VIN to keep the regulator output permanently on.
Light with wavelengths in the red and infrared part of the
spectrum have the most detrimental effect; thus, the fluores-
cent lighting used inside most buildings has very little effect
on performance.
A 1MΩ pulldown resistor ties the VEN input to ground, this en-
sures that the device will remain off when the enable pin is
left open circuit. To ensure proper operation, the signal source
used to drive the VEN input must be able to swing above and
below the specified turn-on/off voltage thresholds listed in the
Electrical Characteristics section under VIL and VIH.
MICRO SMD MOUNTING
The micro SMD package requires specific mounting tech-
niques, which are detailed in Texas Instruments Application
Note AN-1112.
www.ti.com
10
Physical Dimensions inches (millimeters) unless otherwise noted
4-Bump Ultra-Thin micro SMD Package (0.35 mm Pitch)
Package Number UVK04AAA
The dimensions for X1, X2 and X3 are given as:
X1 = 0.65 mm ± 0.030 mm
X2 = 0.65 mm ± 0.030 mm
X3 = 0.40 mm ± 0.045 mm
11
www.ti.com
Notes
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明