PCA9538DBRG4 [TI]
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS; 远程8位I2C和SMBus低功耗I / O扩展器,带有中断输出,复位和配置寄存器型号: | PCA9538DBRG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS |
文件: | 总29页 (文件大小:480K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
FEATURES
•
Low Standby Current Consumption of
1 µA Max
•
Power-Up With All Channels Configured as
Inputs
•
•
•
•
I2C to Parallel Port Expander
Open-Drain Active-Low Interrupt Output
Active-Low Reset Input
•
•
•
No Glitch on Power Up
Noise Filter on SCL/SDA Inputs
Latched Outputs With High-Current Drive
Maximum Capability for Directly Driving LEDs
Operating Power-Supply Voltage Range of
2.3 V to 5.5 V
•
•
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
•
•
•
5-V Tolerant I/O Ports
400-kHz Fast I2C Bus
ESD Protection Exceeds JESD 22
–
–
–
2000-V Human-Body Model (A114-A)
200-V Machine Model (A115-A)
Two Hardware Address Pins Allow up to Four
Devices on the I2C/SMBus
•
•
Input/Output Configuration Register
Polarity Inversion Register
1000-V Charged-Device Model (C101)
RGV PACKAGE
(TOP VIEW)
DB, DBQ, DGV, DW, OR PW PACKAGE
(TOP VIEW)
RGT PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
A0
A1
V
CC
16 15 14 13
16 15 14 13
1
12
RESET
P0
SCL
INT
P7
SDA
SCL
INT
P7
P6
P5
1
12
RESET
SCL
INT
P7
RESET
P0
2
3
4
11
10
9
2
3
11
10
P0
P1
P2
P1
P1
P2
P3
4
9
P6
P2
P6
5
6
7
8
5
6
7
8
GND
P4
DESCRIPTION/ORDERING INFORMATION
This 8-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. It
provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial
clock (SCL), serial data (SDA)].
The PCA9538 consists of one 8-bit Configuration (input or output selection), Input Port, Output Port, and Polarity
Inversion (active high or active low) registers. At power on, the I/Os are configured as inputs. However, the
system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data
for each input or output is kept in the corresponding Input Port or Output Port register. The polarity of the Input
Port register can be inverted with the Polarity Inversion register. All registers can be read by the system master.
The system master can reset the PCA9538 in the event of a timeout or other improper operation by asserting a
low in the RESET input. The power-on reset puts the registers in their default state and initializes the I2C/SMBus
state machine. The RESET pin causes the same reset/initialization to occur without powering down the part.
The PCA9538 open-drain interrupt (INT) output is activated when any input state differs from its corresponding
Input Port register state and is used to indicate to the system master that an input state has changed.
INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the
remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via
the I2C bus. Thus, the PCA9538 can remain a simple slave device.
The device outputs (latched) have high-current drive capability for directly driving LEDs. It has low current
consumption.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2006–2007, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
Two hardware pins (A0 and A1) are used to program and vary the fixed I2C address and allow up to four
devices to share the same I2C bus or SMBus.
ORDERING INFORMATION
TA
PACKAGE(1)
ORDERABLE PART NUMBER
PCA9538RGTR
PCA9538RGVR
PCA9538DBQR
PCA9538DW
TOP-SIDE MARKING
PREVIEW
QFN – RGT
QFN – RGV
QSOP – DBQ
Reel of 3000
Reel of 2500
Reel of 2500
Tube of 40
PREVIEW
PD538
SOIC – DW
SSOP – DB
PCA9538
PD538
Reel of 2000
Reel of 2000
Tube of 80
PCA9538DWR
–40°C to 85°C
PCA9538DBR
PCA9538DB
Tube of 90
PCA9538PW
TSSOP – PW
TVSOP – DGV
PD538
PD538
Reel of 2000
Reel of 2000
PCA9538PWR
PCA9538DGVR
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
TERMINAL FUNCTIONS
NO.
QSOP (DBQ),
NAME
DESCRIPTION
SSOP (DB),
TSSOP (PW), OR
TVSOP (DGV)
QFN (RGT) OR
QFN (RGV)
1
2
15
16
A0
A1
Address input. Connect directly to VCC or ground.
Address input. Connect directly to VCC or ground.
Active-low reset input. Connect to VCC through a pullup resistor if no active
connection is used.
3
1
RESET
4
5
2
3
P0
P1
P-port input/output. Push-pull design structure.
P-port input/output. Push-pull design structure.
P-port input/output. Push-pull design structure.
P-port input/output. Push-pull design structure.
Ground
6
4
P2
7
5
P3
8
6
GND
P4
9
7
P-port input/output. Push-pull design structure.
P-port input/output. Push-pull design structure.
P-port input/output. Push-pull design structure.
P-port input/output. Push-pull design structure.
Interrupt output. Connect to VCC through a pullup resistor.
Serial clock bus. Connect to VCC through a pullup resistor.
Serial data bus. Connect to VCC through a pullup resistor.
Supply voltage
10
11
12
13
14
15
16
8
P5
9
P6
10
11
12
13
14
P7
INT
SCL
SDA
VCC
2
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
FUNCTIONAL BLOCK DIAGRAM
13
Interrupt
LP Filter
Logic
INT
1
2
A0
A1
P7−P0
14
15
SCL
SDA
2
Input
Filter
I C Bus
Control
Shift
Register
I/O
Port
8 Bits
Write Pulse
Read Pulse
3
16
8
RESET
Power-On
Reset
V
CC
GND
A. Pin numbers shown are for the DB, DBQ, DGV, DW, or PW package.
3
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
SIMPLIFIED SCHEMATIC OF P0 TO P7
Data From
Shift Register
Configuration
Output Port
Register Data
Register
V
CC
Data From
Shift Register
Q1
D
Q
FF
K
Write Configuration
Pulse
D
C
Q
Q
C
Q
FF
K
P0 to P7
Write Pulse
ESD Protection
Diode
Q2
Output Port
Register
Input Port
Register
GND
Input Port
Register Data
D
Q
FF
K
Read Pulse
C
Q
To INT
Data From
Shift Register
Polarity
Register Data
D
C
Q
Q
FF
K
Write Polarity
Pulse
Polarity
Inversion
Register
A. At power-on reset, all registers return to default values.
I/O Port
When an I/O is configured as an input, FETs Q1 and Q2 are off, creating a high-impedance input. The input
voltage may be raised above VCC to a maximum of 5.5 V.
If the I/O is configured as an output, Q1 or Q2 is enabled depending on the state of the output port register. In
this case, there are low impedance paths between the I/O pin and either VCC or GND. The external voltage
applied to this I/O pin should not exceed the recommended levels for proper operation.
I2C Interface
The bidirectional I2C bus consists of the serial clock (SCL) and serial data (SDA) lines. Both lines must be
connected to a positive supply through a pull-up resistor when connected to the output stages of a device. Data
transfer may be initiated only when the bus is not busy.
I2C communication with this device is initiated by a master sending a Start condition, a high-to-low transition on
the SDA input/output while the SCL input is high (see Figure 1). After the Start condition, the device address
byte is sent, most significant bit (MSB) first, including the data direction bit (R/W).
After receiving the valid address byte, this device responds with an acknowledge (ACK), a low on the SDA
input/output during the high of the ACK-related clock pulse. The address inputs (A0–A1) of the slave device
must not be changed between the Start and the Stop conditions.
On the I2C bus, only one data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the high pulse of the clock period, as changes in the data line at this time are interpreted as control
commands (Start or Stop) (see Figure 2).
A Stop condition, a low-to-high transition on the SDA input/output while the SCL input is high, is sent by the
master (see Figure 1).
4
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
Any number of data bytes can be transferred from the transmitter to receiver between the Start and the Stop
conditions. Each byte of eight bits is followed by one ACK bit. The transmitter must release the SDA line before
the receiver can send an ACK bit. The device that acknowledges must pull down the SDA line during the ACK
clock pulse so that the SDA line is stable low during the high pulse of the ACK-related clock period (see
Figure 3). When a slave receiver is addressed, it must generate an ACK after each byte is received. Similarly,
the master must generate an ACK after each byte that it receives from the slave transmitter. Setup and hold
times must be met to ensure proper operation.
A master receiver will signal an end of data to the slave transmitter by not generating an acknowledge (NACK)
after the last byte has been clocked out of the slave. This is done by the master receiver by holding the SDA line
high. In this event, the transmitter must release the data line to enable the master to generate a Stop condition.
SDA
SCL
S
P
Start Condition
Stop Condition
Figure 1. Definition of Start and Stop Conditions
SDA
SCL
Data Line
Stable;
Data Valid
Change
of Data
Allowed
Figure 2. Bit Transfer
Data Output
by Transmitter
NACK
Data Output
by Receiver
ACK
SCL From
Master
1
2
8
9
S
Start
Clock Pulse for
Condition
Acknowledgment
Figure 3. Acknowledgment on I2C Bus
5
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
Interface Definition Table
BIT
BYTE
7 (MSB)
6
H
5
H
4
L
3
L
2
1
0 (LSB)
R/W
I2C slave address
Px I/O data bus
H
A1
P2
A0
P1
P7
P6
P5
P4
P3
P0
Device Address
Figure 4 shows the address byte of the PCA9538.
Slave Address
1
1
1
0
0
A1 A0 R/W
Hardware
Selectable
Fixed
Figure 4. PCA9538 Address
Address Reference Table
INPUTS
I2C BUS SLAVE ADDRESS
A1
L
A0
L
112 (decimal), 70 (hexadecimal)
113 (decimal), 71 (hexadecimal)
114 (decimal), 72 (hexadecimal)
115 (decimal), 73 (hexadecimal)
L
H
L
H
H
H
The last bit of the slave address defines the operation (read or write) to be performed. When it is high (1), a read
is selected while a low (0) selects a write operation.
Control Register and Command Byte
Following the successful Acknowledgment of the address byte, the bus master sends a command byte which is
stored in the control register in the PCA9538 (see Figure 5). Two bits of this command byte state the operation
(read or write) and the internal register (input, output, polarity inversion or configuration) that will be affected.
This register can be written or read through the I2C bus. The command byte is sent only during a write
transmission.
Once a command byte has been sent, the register that was addressed continues to be accessed by reads until
a new command byte has been sent.
0
0
0
0
0
0
B1 B0
Figure 5. Control Register Bits
Command Byte Table
CONTROL REGISTER BITS
COMMAND BYTE
(HEX)
REGISTER
PROTOCOL
POWER-UP DEFAULT
B1
0
B0
0
0x00
0x01
0x02
0x03
Input Port
Output Port
Read byte
XXXX XXXX
1111 1111
0000 0000
1111 1111
0
1
Read/write byte
Read/write byte
Read/write byte
1
0
Polarity Inversion
Configuration
1
1
6
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
Register Descriptions
The Input Port register (register 0) reflects the incoming logic levels of the pins, regardless of whether the pin is
defined as an input or an output by the Configuration register. It only acts on read operation. Writes to these
registers have no effect. The default value, X, is determined by the externally applied logic level.
Before a read operation, a write transmission is sent with the command byte to indicate to the I2C device that the
Input Port register will be accessed next.
Register 0 (Input Port Register) Table
BIT
I7
X
I6
X
I5
X
I4
X
I3
X
I2
X
I1
X
I0
X
DEFAULT
The Output Port register (register 1) shows the outgoing logic levels of the pins defined as outputs by the
Configuration register. Bit values in this register have no effect on pins defined as inputs. In turn, reads from this
register reflect the value that is in the flip-flop controlling the output selection, not the actual pin value.
Register 1 (Output Port Register) Table
BIT
O7
1
O6
1
O5
1
O4
1
O3
1
O2
1
O1
1
O0
1
DEFAULT
The Polarity Inversion register (register 2) allows polarity inversion of pins defined as inputs by the Configuration
register. If a bit in this register is set (written with 1), the corresponding port pin polarity is inverted. If a bit in this
register is cleared (written with a 0), the corresponding port pin original polarity is retained.
Register 2 (Polarity Inversion Register) Table
BIT
N7
0
N6
0
N5
0
N4
0
N3
0
N2
0
N1
0
N0
0
DEFAULT
The Configuration register (register 3) configures the directions of the I/O pins. If a bit in this register is set to 1,
the corresponding port pin is enabled as an input with a high-impedance output driver. If a bit in this register is
cleared to 0, the corresponding port pin is enabled as an output.
Register 3 (Configuration Register) Table
BIT
C7
1
C6
1
C5
1
C4
1
C3
1
C2
1
C1
1
C0
1
DEFAULT
Power-On Reset
When power (from 0 V) is applied to VCC, an internal power-on reset holds the PCA9538 in a reset condition
until VCC has reached VPOR. At that point, the reset condition is released and the PCA9538 registers and
SMBus/I2C state machine will initialize to their default states. After that, VCC must be lowered to below 0.2 V and
then back up to the operating voltage for a power-reset cycle.
RESET Input
The RESET input can be asserted to reset the system while keeping the VCC at its operating level. A reset can
be accomplished by holding the RESET pin low for a minimum of tW. The PCA9538 registers and I2C/SMBus
state machine are changed to their default states once RESET is low (0). Once RESET is high (1), the I/O levels
at the P port can be changed externally or through the master. This input requires a pullup resistor to VCC if no
active connection is used.
7
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
Interrupt Output (INT)
An interrupt is generated by any rising or falling edge of the port inputs in the input mode. After time tiv, the
signal INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original
setting, data is read from the port that generated the interrupt or in a Stop event. Resetting occurs in the read
mode at the acknowledge (ACK) or not acknowledge (NACK) bit after the rising edge of the SCL signal. In a
Stop event, INT is cleared after the rising edge of SDA. Interrupts that occur during the ACK or NACK clock
pulse can be lost (or be very short) due to the resetting of the interrupt during this pulse. Each change of the
I/Os after resetting is detected and is transmitted as INT.
Reading from or writing to another device does not affect the interrupt circuit, and a pin configured as an output
cannot cause an interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur if the
state of the pin does not match the contents of the Input Port register.
The INT output has an open-drain structure and requires pullup resistor to VCC
.
Bus Transactions
Data is exchanged between the master and PCA9538 through write and read commands.
Writes
Data is transmitted to the PCA9538 by sending the device address and setting the least-significant bit (LSB) to a
logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which
register receives the data that follows the command byte (see Figure 6 and Figure 7). There is no limitation on
the number of data bytes sent in one write transmission.
SCL
1
2
3
4
5
6
7
8
9
Slave Address
Command Byte
Data to Port
Data 1
S
1
1
1
0
0
A1 A0
0
A
0
0
0
0
0
0
0
1
A
A
P
SDA
ACK From Slave
ACK From Slave
R/W ACK From Slave
Start Condition
Write to Port
Data Out
From Port
Data 1 Valid
t
pv
Figure 6. Write to Output Port Register
<br/>
SCL
1
2
3
4
5
6
7
8
0
9
Slave Address
Command Byte
Data to Register
Data
SDA
S
1
1
1
0
0
A1 A0
A
0
0
0
0
0
0
1
1/0
A
A
P
Start Condition
R/W ACK From Slave
ACK From Slave
ACK From Slave
Data to
Register
Figure 7. Write to Configuration or Polarity Inversion Registers
8
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
Reads
The bus master first must send the PCA9538 address with the LSB set to a logic 0 (see Figure 4 for device
address). The command byte is sent after the address and determines which register is accessed. After a
restart, the device address is sent again but, this time, the LSB is set to a logic 1. Data from the register defined
by the command byte then is sent by the PCA9538 (see Figure 8 and Figure 9). After a restart, the value of the
register defined by the command byte matches the register being accessed when the restart occurred. Data is
clocked into the register on the rising edge of the ACK clock pulse. There is no limitation on the number of data
bytes received in one read transmission, but when the final byte is received, the bus master must not
acknowledge the data.
ACK From
Master
ACK From
Slave
ACK From
Slave
ACK From
Slave
Data from Register
Data
Slave Address
Slave Address
Command Byte
A
S
A
1
1
1
0
0
A1 A0 1
R/W
A
S
1
1
1
0
0 A1 A0 0
A
R/W
NACK From
Master
Data from Register
Data
P
NA
Last Byte
Figure 8. Read From Register
<br/>
1
2
3
4
5
6
7
8
9
SCL
SDA
Data From Port
Data 1
Slave Address
Data From Port
Data 4
S
1
1
1
0
0
A1 A0
R/W
0
A
P
A
NA
Start
Condition
NACK From
ACK From
Slave
ACK From
Master
Stop
Condition
Master
Read From
Port
Data Into
Port
Data 2
Data 3
Data 4
Data 5
t
ph
t
ps
INT
t
iv
t
ir
A. This figure assumes the command byte has previously been programmed with 00h.
B. Transfer of data can be stopped at any moment by a Stop condition.
C. This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address
call and actual data transfer from the P port. See Figure 8 for these details.
Figure 9. Read From Input Port Register
9
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.5
–0.5
–0.5
MAX
UNIT
VCC
VI
Supply voltage range
Input voltage range(2)
Output voltage range(2)
6
V
6
6
V
VO
IIK
V
Input clamp current
VI < 0
–20
–20
±20
50
mA
mA
mA
mA
mA
IOK
IIOK
IOL
IOH
Output clamp current
VO < 0
Input/output clamp current
Continuous output low current
Continuous output high current
Continuous current through GND
Continuous current through VCC
VO < 0 or VO > VCC
VO = 0 to VCC
VO = 0 to VCC
–50
–250
160
82
ICC
mA
DB package
DBQ package
DGV package
DW package
PW package
RGT package
RGV package
90
86
θJA
Package thermal impedance(3)
46
°C/W
°C
88
TBD
TBD
150
Tstg
Storage temperature range
–65
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
(3) The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions
MIN
2.3
MAX
5.5
UNIT
VCC
VIH
Supply voltage
V
SCL, SDA
0.7 × VCC
2
5.5
High-level input voltage
V
V
A0, A1, RESET, P7–P0
SCL, SDA
5.5
–0.5 0.3 × VCC
VIL
Low-level input voltage
A0, A1, RESET, P7–P0
P7–P0
–0.5
0.8
–10
25
IOH
IOL
TA
High-level output current
Low-level output current
Operating free-air temperature
mA
mA
°C
P7–P0
–40
85
10
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
II = –18 mA
VCC
2.3 V to 5.5 V
VPOR
MIN
TYP(1)
MAX UNIT
VIK
Input diode clamp voltage
–1.2
V
VPOR Power-on reset voltage
VI = VCC or GND, IO = 0
1.5
1.65
V
2.3 V
1.8
2.6
4.1
4.1
1.7
2.5
4
3 V
IOH = –8 mA
4.5 V
4.75 V
2.3 V
VOH
P-port high-level output voltage(2)
V
3 V
IOH = –10 mA
VOL = 0.4 V
VOL = 0.5 V
4.5 V
4.75 V
2.3 V to 5.5 V
2.3 V
4
SDA
3
8
10
14
17
35
13
19
24
45
10
8
3 V
8
4.5 V
8
4.75 V
2.3 V
8
IOL
P port(3)
mA
10
10
10
10
3
3 V
VOL = 0.7 V
4.5 V
4.75 V
2.3 V to 5.5 V
INT
VOL = 0.4 V
SCL, SDA
A0, A1, RESET
P port
±1
±1
1
II
VI = VCC or GND
2.3 V to 5.5 V
µA
IIH
IIL
VI = VCC
2.3 V to 5.5 V
2.3 V to 5.5 V
5.5 V
µA
µA
P port
VI = GND
–1
175
90
65
150
40
20
1
104
50
VI = VCC or GND, IO = 0,
I/O = inputs, fscl = 400 kHz, No load
3.6 V
2.7 V
20
Operating mode
Standby mode
5.5 V
60
VI = VCC or GND, IO = 0,
I/O = inputs, fscl = 100 kHz, No load
ICC
3.6 V
15
µA
2.7 V
8
5.5 V
0.25
0.2
0.1
VI = VCC or GND, IO = 0,
I/O = inputs, fscl = 0 kHz, No load
3.6 V
0.9
0.8
2.7 V
One input at VCC – 0.6 V,
Other inputs at VCC or GND
2.3 V to 5.5 V
1.5
1
Additional current in standby
mode
∆ICC
mA
All LED I/Os at VI = 4.3 V,
fscl = 0 kHz
5.5 V
Ci
SCL
VI = VCC or GND
2.3 V to 5.5 V
4
5.5
8
5
6.5
9.5
pF
pF
SDA
P port
Cio
VIO = VCC or GND
2.3 V to 5.5 V
(1) All typical values are at nominal supply voltage (2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C.
(2) The total current sourced by all I/Os must be limited to 85 mA.
(3) Each I/O must be externally limited to a maximum of 25 mA, and the P port (P7–P0) must be limited to a maximum current of 200 mA.
11
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
I2C Interface Timing Requirements
over operating free-air temperature range (unless otherwise noted) (see Figure 10)
STANDARD MODE
I2C BUS
FAST MODE
I2C BUS
UNIT
MIN
0
MAX
MIN
0
MAX
fscl
tsch
tscl
tsp
I2C clock frequency
I2C clock high time
I2C clock low time
I2C spike time
I2C serial-data setup time
I2C serial-data hold time
I2C input rise time
I2C input fall time
100
400 kHz
4
0.6
1.3
µs
µs
4.7
50
50
ns
ns
ns
ns
ns
ns
µs
µs
µs
µs
ns
tsds
tsdh
ticr
250
0
100
0
(1)
1000 20 + 0.1Cb
300 20 + 0.1Cb
300 20 + 0.1Cb
300
300
300
(1)
(1)
ticf
tocf
tbuf
tsts
tsth
tsps
I2C output fall time
10-pF to 400-pF bus
I2C bus free time between Stop and Start
I2C Start or repeated Start condition setup
I2C Start or repeated Start condition hold
I2C Stop condition setup
4.7
4.7
4
1.3
0.6
0.6
0.6
50
4
tvd(data) Valid data time
SCL low to SDA output valid
300
ACK signal from SCL low to
SDA (out) low
tvd(ack) Valid data time of ACK condition
0.3
3.45
400
0.1
0.9
µs
Cb
I2C bus capacitive load
400
ns
(1) Cb = Total capacitance of one bus in pF
RESET Timing Requirements
over operating free-air temperature range (unless otherwise noted)
STANDARD MODE
I2C BUS
FAST MODE
I2C BUS
PARAMETER
UNIT
MIN
MAX
MIN
MAX
t<Subscri
pt>w</Su Reset pulse duration
bscript>
4
4
ns
tREC
Reset recovery time
Time to reset
0
0
ns
ns
tRESET
400
400
Switching Characteristics
over operating free-air temperature range (unless otherwise noted) (see Figure 11 and Figure 12)
STANDARD MODE
FAST MODE
I2C BUS
I2C BUS
MIN
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
UNIT
MAX
4
MIN
MAX
tiv
Interrupt valid time
Interrupt reset delay time
Output data valid
P port
SCL
INT
INT
4
4
µs
µs
ns
ns
µs
tir
4
tpv
tps
tph
SCL
P7–P0
SCL
200
200
Input data setup time
Input data hold time
P port
P port
100
1
100
1
SCL
12
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
TYPICAL CHARACTERISTICS
TA = 25°C (unless otherwise noted)
SUPPLY CURRENT
vs
TEMPERATURE
QUIESCENT SUPPLY CURRENT
vs
TEMPERATURE
35
30
25
20
15
10
5
55
50
45
40
35
30
25
20
15
10
5
VCC = 5 V
VCC = 5 V
fSCL = 400 kHz
I/Os unloaded
VCC = 3.3 V
VCC = 3.3 V
VCC = 2.5 V
VCC = 2.5 V
SCL = VCC
0
0
-40
-15
10
35
60
85
-40
-15
10
35
60
85
TA – Free-Air Temperature – °C
TA – Free-Air Temperature – °C
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SUPPLY CURRENT
vs
NUMBER OF I/Os HELD LOW
70
600
550
500
450
400
350
300
250
200
150
100
50
fSCL = 400 kHz
I/Os unloaded
VCC = 5 V
60
50
40
30
20
10
0
TA = –40°C
TA = 25°C
TA = 85°C
0
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
0
1
2
3
4
5
6
7
8
VCC – Supply Voltage – V
Number of I/Os Held Low
13
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
TYPICAL CHARACTERISTICS (continued)
TA = 25°C (unless otherwise noted)
I/O OUTPUT LOW VOLTAGE
I/O SINK CURRENT
vs
vs
TEMPERATURE
OUTPUT LOW VOLTAGE
275
250
225
200
175
150
125
100
75
30
25
20
15
10
5
VCC = 2.5 V
VCC = 2.5 V, IOL = 10 mA
TA = –40°C
TA = 25°C
VCC = 5 V, IOL = 10 mA
TA = 85°C
VCC = 2.5 V, IOL = 1 mA
VCC = 5 V, IOL = 1 mA
50
25
0
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
-40
-15
10
35
60
85
VOL – Output Low Voltage – V
TA – Free-Air Temperature – °C
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
60
55
50
45
40
35
30
25
20
15
10
5
40
35
30
25
20
15
10
5
VCC = 5 V
VCC = 3.3 V
TA = –40°C
TA = –40°C
TA = 25°C
TA = 25°C
TA = 85°C
TA = 85°C
0
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
VOL – Output Low Voltage – V
VOL – Output Low Voltage – V
14
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
TYPICAL CHARACTERISTICS (continued)
TA = 25°C (unless otherwise noted)
I/O OUTPUT HIGH VOLTAGE
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
vs
TEMPERATURE
275
250
225
200
175
150
125
100
75
35
30
25
20
15
10
5
VCC = 2.5 V
VCC = 2.5 V, IOL = 10 mA
TA = –40°C
TA = 25°C
VCC = 5 V, IOL = 10 mA
TA = 85°C
VCC = 2.5 V, IOL = 1 mA
VCC = 5 V, IOL = 1 mA
50
25
0
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
-40
-15
10
35
60
85
(VCC – VOH) – Output High Voltage – V
TA – Free-Air Temperature – °C
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
50
45
40
35
30
25
20
15
10
5
VCC = 3.3 V
VCC = 5 V
TA = –40°C
TA = –40°C
TA = 25°C
TA = 25°C
TA = 85°C
TA = 85°C
0
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
(VCC – VOH) – Output High Voltage – V
(VCC – VOH) – Output High Voltage – V
15
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
TYPICAL CHARACTERISTICS (continued)
TA = 25°C (unless otherwise noted)
OUTPUT HIGH VOLTAGE
vs
SUPPLY VOLTAGE
6
TA = 25°C
5
4
IOH = –8 mA
3
IOH = –10 mA
2
1
0
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
VCC – Supply Voltage – V
16
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
PARAMETER MEASUREMENT INFORMATION
V
CC
R = 1 kΩ
L
SDA
DUT
C = 50 pF
L
(see Note A)
SDA LOAD CONFIGURATION
Three Bytes for Complete
Device Programming
Stop
Start
Address
Bit 7
(MSB)
R/W
Bit 0
(LSB)
Data
Bit 07
(MSB)
Data
Bit 10 Condition
(LSB)
Stop
Address
Bit 6
Address
Bit 1
ACK
(A)
Condition Condition
(P) (S)
(P)
t
scl
t
sch
0.7 × V
0.3 × V
CC
SCL
SDA
CC
t
icr
t
sts
t
PHL
t
icf
t
buf
t
t
sp
PLH
0.7 × V
0.3 × V
CC
CC
t
icf
t
icr
t
sdh
t
sps
t
sth
t
sds
Repeat
Start
Condition
Stop
Condition
Start or
Repeat
Start
Condition
VOLTAGE WAVEFORMS
BYTE
1
DESCRIPTION
2
I C address
2, 3
P-port data
A. CL includes probe and jig capacitance.
B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C. All parameters and waveforms are not applicable to all devices.
Figure 10. I2C Interface Load Circuit and Voltage Waveforms
17
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
PARAMETER MEASUREMENT INFORMATION (continued)
V
CC
R
L
= 4.7 kΩ
INT
DUT
C
L
= 100 pF
(see Note A)
INTERRUPT LOAD CONFIGURATION
ACK
From Slave
ACK
From Slave
Start
Condition
8 Bits
(One Data Byte)
From Port
R/W
Slave Address
Data From Port
Data 2
Data 1
A
1
P
S
1
1
1
0
0
A1 A0
1
A
1
2
3
4
5
6
7
8
A
A
t
ir
B
B
t
ir
INT
A
t
iv
t
sps
A
Data
Into
Port
Address
Data 1
Data 2
0.7 × V
0.3 × V
CC
0.7 × V
0.3 × V
CC
SCL
INT
R/W
A
CC
CC
t
iv
t
ir
0.7 × V
0.3 × V
0.7 × V
0.3 × V
CC
CC
INT
P
n
CC
CC
View A−A
A. CL includes probe and jig capacitance.
View B−B
B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C. All parameters and waveforms are not applicable to all devices.
Figure 11. Interrupt Load Circuit and Voltage Waveforms
18
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
PARAMETER MEASUREMENT INFORMATION (continued)
Pn
500 W
DUT
2 × V
CC
C
= 50 pF
L
500 W
(see Note A)
P-PORT LOAD CONFIGURATION
0.7 × V
CC
SCL
SDA
P0
A
P3
0.3 × V
CC
Slave
ACK
t
pv
(see Note B)
P
n
Last Stable Bit
Unstable
Data
WRITE MODE (R/W = 0)
0.7 × V
0.3 × V
CC
SCL
P0
A
P3
CC
t
ph
t
ps
0.7 × V
0.3 × V
CC
P
n
CC
READ MODE (R/W = 1)
A. CL includes probe and jig capacitance.
B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C. The outputs are measured one at a time, with one transition per measurement.
D. All parameters and waveforms are not applicable to all devices.
Figure 12. P-Port Load Circuit and Voltage Waveforms
19
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
PARAMETER MEASUREMENT INFORMATION (continued)
V
CC
Pn
500 W
R
L
= 1 kΩ
DUT
2 × V
CC
SDA
DUT
C
L
= 50 pF
500 W
(see Note A)
C
L
= 50 pF
(see Note A)
SDA LOAD CONFIGURATION
P-PORT LOAD CONFIGURATION
Start
SCL
ACK or Read Cycle
SDA
0.3 y V
CC
t
RESET
RESET
V /2
CC
t
REC
t
w
Px
V /2
CC
(see Note D)
t
RESET
A. CL includes probe and jig capacitance.
B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C. The outputs are measured one at a time, with one transition per measurement.
D. I/Os are configured as inputs.
E. All parameters and waveforms are not applicable to all devices.
Figure 13. Reset Load Circuits and Voltage Waveforms
20
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
APPLICATION INFORMATION
Figure 14 shows an application in which the PCA9538 can be used.
V
CC
100 kW
(y3)
(5 V)
2 kW
10 kW 10 kW
10 kW
10 kW
V
CC
V
CC
Subsystem 1
(e.g., temperature sensor)
SDA
SCL
SDA
P0
P1
Master
SCL
INT
Controller
GND
INT
INT
P2
P3
RESET
RESET
PCA9538
RESET
Subsystem 2
(e.g., counter)
P4
A
P5
P6
P7
Controlled Device
(e.g., CBT device)
ENABLE
A1
A0
B
GND
ALARM
Subsystem 3
(e.g., alarm system)
V
CC
A. Device address is configured as 1110000 for this example.
B. P0, P2, and P3 are configured as outputs.
C. P1, P4, and P5 are configured as inputs.
D. P6 and P7 are not used and must be configured as outputs.
Figure 14. Typical Application
21
Submit Documentation Feedback
PCA9538
REMOTE 8-BIT I2C AND SMBus LOW-POWER I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS126D–SEPTEMBER 2006–REVISED MARCH 2007
APPLICATION INFORMATION (continued)
Minimizing ICC When I/Os Control LEDs
When the I/Os are used to control LEDs, normally they are connected to VCC through a resistor as shown in
Figure 14. The LED acts as a diode, so when the LED is off, the I/O VIN is about 1.2 V less than VCC. ICC in
Electrical Characteristics shows how ICC increases as VIN becomes lower than VCC
.
For battery-powered applications, it is essential that the voltage of I/O pins is greater than or equal to VCC when
the LED is off to minimize current consumption. Figure 15 shows a high-value resistor in parallel with the LED.
Figure 16 shows VCC less than the LED supply voltage by at least 1.2 V. Both of these methods maintain the I/O
VIN at or above VCC and prevents additional supply current consumption when the LED is off.
V
CC
LED
100 kW
V
CC
LEDx
Figure 15. High-Value Resistor in Parallel With LED
5 V
3.3 V
LED
V
CC
LEDx
Figure 16. Device Supplied by a Lower Voltage
22
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
19-Mar-2007
PACKAGING INFORMATION
Orderable Device
PCA9538DB
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
SSOP
DB
16
16
16
16
16
16
16
16
16
16
16
16
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
PCA9538DBG4
PCA9538DBR
PCA9538DBRG4
PCA9538DGVR
PCA9538DGVRG4
PCA9538DW
SSOP
SSOP
DB
DB
80 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SSOP
DB
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TVSOP
TVSOP
SOIC
DGV
DGV
DW
DW
PW
PW
PW
PW
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
40 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
PCA9538DWR
PCA9538PW
SOIC
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TSSOP
TSSOP
TSSOP
TSSOP
90 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
PCA9538PWG4
PCA9538PWR
PCA9538PWRG4
90 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
19-Mar-2007
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,23
0,13
M
0,07
0,40
24
13
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–ā8°
0,75
1
12
0,50
A
Seating Plane
0,08
0,15
0,05
1,20 MAX
PINS **
14
16
20
24
38
48
56
DIM
A MAX
A MIN
3,70
3,50
3,70
3,50
5,10
4,90
5,10
4,90
7,90
7,70
9,80
9,60
11,40
11,20
4073251/E 08/00
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
D. Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
M
0,15
15
0,25
0,09
5,60
5,00
8,20
7,40
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
0,10
2,00 MAX
0,05 MIN
PINS **
14
16
20
24
28
30
38
DIM
6,50
5,90
6,50
5,90
7,50
8,50
7,90
10,50
9,90
10,50 12,90
A MAX
A MIN
6,90
9,90
12,30
4040065 /E 12/01
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
M
0,10
0,65
14
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°–8°
A
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
8
14
16
20
24
28
DIM
3,10
2,90
5,10
4,90
5,10
4,90
6,60
6,40
7,90
9,80
9,60
A MAX
A MIN
7,70
4040064/F 01/97
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to
discontinue any product or service without notice. Customers should obtain the latest relevant information
before placing orders and should verify that such information is current and complete. All products are sold
subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent
TI deems necessary to support this warranty. Except where mandated by government requirements, testing
of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible
for their products and applications using TI components. To minimize the risks associated with customer
products and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent
right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine,
or process in which TI products or services are used. Information published by TI regarding third-party
products or services does not constitute a license from TI to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or
other intellectual property of the third party, or a license from TI under the patents or other intellectual
property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not
responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service
and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Amplifiers
Data Converters
DSP
Interface
Applications
Audio
Automotive
Broadband
Digital Control
Military
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
interface.ti.com
logic.ti.com
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Logic
Power Mgmt
Microcontrollers
Low Power Wireless
power.ti.com
microcontroller.ti.com
www.ti.com/lpw
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明