PCM1741 [TI]
DIGITAL-TO-ANALOG CONVERTER;型号: | PCM1741 |
厂家: | TEXAS INSTRUMENTS |
描述: | DIGITAL-TO-ANALOG CONVERTER |
文件: | 总24页 (文件大小:500K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PCM1741
P
C
M
1
74
1
www.ti.com
+3.3V Single-Supply, 24-Bit, 96kHz Sampling
Enhanced Multilevel, Delta-Sigma, Audio
DIGITAL-TO-ANALOG CONVERTER
FEATURES
APPLICATIONS
●
24-BIT RESOLUTION
● AV RECEIVERS
●
ANALOG PERFORMANCE (VCC = +3.3V):
Dynamic Range: 98dB typ
SNR: 98dB typ
● DVD MOVIE PLAYERS
● DVD ADD-ON CARDS FOR HIGH-END PCs
● HDTV RECEIVERS
THD+N: 0.005% typ
● CAR AUDIO SYSTEMS
Full-Scale Output: 2.05Vp-p typ
● OTHER APPLICATIONS REQUIRING 24-BIT
●
8x OVERSAMPLING DIGITAL FILTER:
Stopband Attenuation: –55dB
Passband Ripple: ±0.03dB
AUDIO
DESCRIPTION
●
●
SAMPLING FREQUENCY: 5kHz to 100kHz
The PCM1741 is a CMOS, monolithic, integrated circuit
which includes stereo Digital-to-Analog Converters
(DACs) and support circuitry in a small SSOP-16 package.
The data converters utilize Texas Instrument’s enhanced
multilevel delta-sigma architecture that employs fourth-
order noise shaping and 8-level amplitude quantization to
achieve excellent dynamic performance and improved toler-
ance to clock jitter. The PCM1741 accepts industry standard
audio data formats with 16- to 24-bit data, providing easy
interfacing to audio DSP and decoder chips. Sampling rates
up to 100kHz are supported. A full set of user-program-
mable functions are accessible through a 3-wire serial
control port that supports register write functions.
SYSTEM CLOCK: 256, 384, 512, 768fS with
Auto Detect
●
●
ACCEPTS 16-, 18-, 20-, AND 24-BIT AUDIO
DATA
DATA FORMATS: Standard, I2S, and Left-
Justified
● USER-PROGRAMMABLE MODE CONTROLS:
Digital Attenuation: 0dB to –63dB, 0.5dB/Step
Digital De-Emphasis
Digital Filter Roll-Off: Sharp or Slow
Soft Mute
Zero Flags for Each Output
●
●
3.3V SINGLE POWER SUPPLY
5V TOLERANT DIGITAL INPUTS
●
SMALL SSOP-16 PACKAGE
Copyright © 2000, Texas Instruments Incorporated
SBAS175
Printed in U.S.A. December, 2000
SPECIFICATIONS
All specifications at TA = +25°C, VCC = 5.0V, VDD = 3.3V, fS = 44.1kHz, system clock = 384fS, and 24-bit data, unless otherwise noted.
PCM1741E
PARAMETER
RESOLUTION
CONDITIONS
MIN
TYP
MAX
UNITS
24
Bits
DATA FORMAT
Audio Data Interface Formats
Standard, I2S, Left-Justified
Audio Data Bit Length
Audio Data Format
16-, 18-, 20-, 24-Bits Selectable
MSB-First, Binary Two’s Complement
Sampling Frequency (fS)
System Clock Frequency
5
100
kHz
256, 384, 512, 768fS
TTL-Compatible
DIGITAL INPUT/OUTPUT
Logic Family
Input Logic Level
VIH
VIL
2.0
VDC
VDC
0.8
Input Logic Current
(1)
IIH
IIL
IIH
IIL
VIN = VDD
VIN = 0V
VIN = VDD
VIN = 0V
10
µA
µA
µA
µA
(1)
–10
100
–10
(2)
65
(2)
Output Logic Level
(3)
VOH
VOL
IOH = –2mA
IOL = +2mA
2.4
VDC
VDC
(3)
1.0
DYNAMIC PERFORMANCE(4)
PCM1741E
THD+N at VOUT = 0dB
fS = 44.1kHz
fS = 96kHz
fS = 44.1kHz
0.005
0.007
1.6
2.0
98
96
98
96
96
0.01
%
%
%
THD+N at VOUT = –60dB
Dynamic Range
fS = 96kHz
%
EIAJ, A-Weighted, fS = 44.1kHz
A-Weighted, fS = 96kHz
EIAJ, A-Weighted, fS = 44.1kHz
A-Weighted, fS = 96kHz
fS = 44.1kHz
92
92
90
dB
dB
dB
dB
dB
dB
dB
Signal-to-Noise Ratio
Channel Separation
Level Linearity Error
fS = 96kHz
VOUT = –90dB
94
±0.5
DC ACCURACY
Gain Error
Gain Mismatch, Channel-to-Channel
Bipolar Zero Error
±1.0
±1.0
±30
±6
±3
±60
% of FSR
% of FSR
mV
VOUT = 0.5 VCC at Bipolar Zero
ANALOG OUTPUT
Output Voltage
Full Scale (0dB)
AC Load
62% of VCC
50% of VCC
Vp-p
VDC
kΩ
Center Voltage
Load Impedance
5
DIGITAL FILTER PERFORMANCE
Filter Characteristics 1, Sharp Roll-Off
Passband
Passband
±0.03dB
–3dB
0.454fS
0.487fS
Stopband
0.546fS
dB
dB
dB
Passband Ripple
Stopband Attenuation
Stopband Attenuation
Filter Characteristics 2, Slow Roll-Off
Passband
±0.03
Stopband = 0.546fS
Stopband = 0.567fS
–50
–55
±0.5dB
0.198fS
0.390fS
Passband
–3dB
Stopband
0.884fS
–40
Passband Ripple
Stopband Attenuation
Delay Time
±0.5
dB
dB
Stopband = 0.884fS
20/fS
±0.1
sec
dB
De-Emphasis Error
PCM1741
2
SBAS175
SPECIFICATIONS (Cont.)
All specifications at TA = +25°C, VCC = 5.0V, VDD = 3.3V, system clock = 384fS (fS = 44.1kHz), and 24-bit data, unless otherwise noted.
PCM1741E
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
ANALOG FILTER PERFORMANCE
Frequency Response
f = 20kHz
f = 44kHz
–0.03
–0.20
dB
dB
POWER SUPPLY REQUIREMENTS(4)
Voltage Range, VDD
VCC
+2.7
+2.7
+3.3
+3.0
6.0
13.0
7.0
7.0
43
66
+3.6
+3.6
10
VDC
VDC
mA
Supply Current, IDD
fS = 44.1kHz
fS = 96kHz
fS = 44.1kHz
fS = 96kHz
fS = 44.1kHz
fS = 96kHz
mA
ICC
11
88
mA
mA
mW
mW
Power Dissipation
TEMPERATURE RANGE
Operation Temperature
Thermal Resistance
–25
+85
°C
θJA
SSOP-16
115
°C/W
NOTES: (1) Pins 1, 2, 3, 16 (SCK, BCK, LRCK, DATA). (2) Pins 13-15 (MD, MC, ML). (3) Pins 11, 12 (ZEROR, ZEROL). (4) Analog performance specifications
are tested with a Shibasoku #725 THD Meter with 400Hz HPF on, 30kHz LPF on, and an average mode with 20kHz bandwidth limiting. The load connected
to the analog output is 5kΩ or larger, via capacitive coupling.
ABSOLUTE MAXIMUM RATINGS
ELECTROSTATIC
Power Supply Voltage, VDD .............................................................. +4.0V
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
VCC .............................................................. +6.5V
Ground Voltage Differences.............................................................. ±0.1V
Digital Input Voltage ................................................ –0.3V to (6.5V + 0.3V)
recommends that all integrated circuits be handled with
Input Current (except power supply) ............................................... ±10mA
Ambient Temperature Under Bias .................................. –40°C to +125°C
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
Storage Temperature ...................................................... –55°C to +150°C
Junction Temperature .................................................................... +150°C
ESD damage can range from subtle performance degradation
Lead Temperature (soldering, 5s)................................................. +260°C
Package Temperature (IR reflow, 10s) .......................................... +235°C
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
PACKAGE
DRAWING
NUMBER
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(1)
TRANSPORT
MEDIA
PRODUCT
PACKAGE
PCM1741E
SSOP-16
322
–25°C to +85°C
PCM1741E
PCM1741E
Rails
"
"
"
"
"
PCM1741E/2K
Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K indicates 2000 devices per reel). Ordering 2000 pieces
of “PCM1741E/2K” will yield a single 2000-piece Tape and Reel.
PCM1741
3
SBAS175
BLOCK DIAGRAM
BCK
LRCK
DATA
Audio
Serial
Port
Output Amp and
Low-Pass Filter
VOUT
L
DAC
8x
Enhanced
Multilevel
Delta-Sigma
Modulator
Oversampling
Digital Filter
with
Function
Controller
VCOM
ML
MC
MD
Output Amp and
Low-Pass Filter
Serial
Control
Port
DAC
VOUT
R
System Clock
System Clock
Manager
Power Supply
Zero Detect
SCK
PIN CONFIGURATION
PIN ASSIGNMENTS
TOP VIEW
SSOP
PIN NAME
TYPE
FUNCTION
1
2
3
BCK
DATA
LRCK
IN
IN
IN
Audio Data Bit Clock Input.(1)
Audio Data Digital Input.(1)
L-Channel and R-Channel Audio Data Latch En-
able Input.(1)
BCK
DATA
LRCK
DGND
VDD
1
2
3
4
5
6
7
8
16 SCK
15 ML
4
5
DGND
VDD
–
–
Digital Ground
Digital Power Supply, +3.3V
Analog Power Supply, +3.3V
Analog Output for L-Channel.
Analog Output for R-Channel.
Analog Ground
6
VCC
–
14 MC
7
VOUTL
OUT
OUT
–
13 MD
8
VOUTR
PCM1741
9
AGND
VCOM
12 ZEROL/NA
10
–
Common Voltage Decoupling.
VCC
11 ZEROR/ZEROA
10 VCOM
11 ZEROR/
ZEROA
OUT
Zero Flag Output for R-Channel/Zero Flag Output
for L/R-Channel.
VOUT
L
12 ZEROL/NA OUT
Zero Flag Output for L-Channel/No Assign.
Mode Control Data Input.(2)
Mode Control Clock Input.(2)
Mode Control Latch Input.(2)
System Clock Input.
V
OUTR
9
AGND
13
14
15
16
MD
MC
ML
IN
IN
IN
IN
SCK
NOTES: (1) Schmitt-trigger input, 5V tolerant. (2) Schmitt-trigger with internal
pull-down, 5V tolerant.
PCM1741
4
SBAS175
TYPICAL PERFORMANCE CURVES
All specifications at TA = +25°C, VCC = VDD = 3.3V, system clock = 384fS (fS = 44.1kHz), and 24-bit input data, unless otherwise noted.
DIGITAL FILTER
Digital Filter (De-Emphasis Off
FREQUENCY RESPONSE PASSBAND
FREQUENCY RESPONSE (Sharp Roll-Off)
(Sharp Roll-Off)
0
–20
0.05
0.04
0.03
0.02
0.01
0
–40
–60
–80
–0.01
–0.02
–0.03
–0.04
–0.05
–100
–120
–140
0
1
2
3
4
0
0
0
0.1
0.2
0.3
0.4
0.5
Frequency (x fS)
Frequency (x fS)
FREQUENCY RESPONSE (Slow Roll-Off)
TRANSITION CHARACTERISTICS (Slow Roll-Off)
0
–20
5
4
3
–40
2
1
–60
0
–80
–1
–2
–3
–4
–5
–100
–120
–140
0
1
2
3
4
0.1
0.2
0.3
0.4
0.5
Frequency (x fS)
Frequency (x fS)
De-Emphasis
DE-EMPHASIS (fS = 32kHz)
DE-EMPHASIS ERROR (fS = 32kHz)
0.0
–1.0
–2.0
–3.0
–4.0
–5.0
–6.0
–7.0
–8.0
–9.0
–10.0
0.5
0.4
0.3
0.2
0.1
0.0
–0.1
–0.2
–0.3
–0.4
–0.5
0
2
4
6
8
10
12
14
2
4
6
8
10
12
14
Frequency (kHz)
Frequency (kHz)
PCM1741
5
SBAS175
TYPICAL PERFORMANCE CURVES (Cont.)
All specifications at TA = +25°C, VCC = VDD = 3.3V, system clock = 384fS (fS = 44.1kHz), and 24-bit input data, unless otherwise noted.
De-Emphasis (Cont.)
DE-EMPHASIS (fS = 44.1kHz)
DE-EMPHASIS ERROR (fS = 44.1kHz)
0.0
–1.0
–2.0
–3.0
–4.0
–5.0
–6.0
–7.0
–8.0
–9.0
–10.0
0.5
0.4
0.3
0.2
0.1
0.0
–0.1
–0.2
–0.3
–0.4
–0.5
18
0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
8
10
12
14
16
20
Frequency (kHz)
Frequency (kHz)
DE-EMPHASIS (fS = 48kHz)
DE-EMPHASIS ERROR (fS = 48kHz)
0.0
–1.0
–2.0
–3.0
–4.0
–5.0
–6.0
–7.0
–8.0
–9.0
–10.0
0.5
0.4
0.3
0.2
0.1
0.0
–0.1
–0.2
–0.3
–0.4
–0.5
18
18
0
2
4
6
8
10
12
14
16
22
0
2
4
6
8
10
12
14
16
22
Frequency (kHz)
Frequency (kHz)
ANALOG DYNAMIC PERFORMANCE
All specifications at TA = +25°C, VCC = 5.0V, VDD = 3.3V, and 24-bit input data, unless otherwise noted.
Supply-Voltage Characteristics
THD+N vs VCC
DYNAMIC RANGE vs VCC
106
104
102
100
98
10
1
–60dB/96kHz, 384fS
44.1kHz, 384fS
–60dB/44.1kHz, 384fS
96
0.1
94
96kHz, 384fS
0dB/96kHz, 384fS
92
0.01
0.001
90
88
0dB/44.1kHz, 384fS
86
2.4
2.7
3
3.3
3.6
3.9
2.4
2.7
3
3.3
3.6
3.9
VCC (V)
VCC (V)
PCM1741
6
SBAS175
TYPICAL PERFORMANCE CURVES (Cont.)
All specifications at TA = +25°C, VCC = VDD = 3.3V, and 24-bit input data, unless otherwise noted.
Supply-Voltage Characteristics (Cont.)
SNR vs VCC
CHANNEL SEPARATION vs VCC
106
104
102
100
98
106
104
102
100
98
44.1kHz, 384fS
44.1kHz, 384fS
96
96
94
94
96kHz, 384fS
92
92
96kHz, 384fS
90
90
88
88
86
86
2.4
2.7
3
3.3
3.6
3.9
4.2
100
100
2.4
–50
–50
2.7
3
3.3
3.6
3.9
100
100
V
CC (V)
VCC (V)
Temperature Characteristics
THD+N vs TA
–60dB/96kHz, 384fS
DYNAMIC RANGE vs TA
44.1kHz, 384fS
106
104
102
100
98
10
1
–60dB/44.1kHz, 384fS
96
0.1
94
96kHz, 384fS
0dB/96kHz, 384fS
92
0.01
90
88
0dB/44.1kHz, 384fS
0.001
86
–50
–25
0
25
50
75
–25
0
25
50
75
Temperature (°C)
Temperature (°C)
SNR vs TA
CHANNEL SEPARATION vs TA
106
104
102
100
98
106
104
102
100
98
44.1kHz, 384fS
44.1kHz, 384fS
96
96
94
94
96kHz, 384fS
92
92
96kHz, 384fS
90
90
88
88
86
86
–50
–25
0
25
Temperature (°C)
50
75
–25
0
25
50
75
Temperature (°C)
PCM1741
7
SBAS175
POWER-ON RESET FUNCTIONS
SYSTEM CLOCK AND RESET
FUNCTIONS
The PCM1741 includes a power-on reset function, as shown in
Figure 2. With the system clock active, and VDD > 2.0V (typical
1.6V to 2.4V), the power-on reset function will be enabled. The
initialization sequence requires 1024 system clocks from the
time VDD > 2.0V. After the initialization period, the PCM1741
will be set to its reset default state, as described in the Mode
Control Register section of this data sheet.
SYSTEM CLOCK INPUT
The PCM1741 requires a system clock for operating the
digital interpolation filters and multilevel delta-sigma modu-
lators. The system clock is applied at the SCK input (pin 16).
Table I shows examples of system clock frequencies for
common audio sampling rates.
Figure 1 shows the timing requirements for the system clock
input. For optimal performance, it is important to use a clock
source with low phase jitter and noise. The PLL1700 multi-
clock generator from Texas Instruments is an excellent choice
for providing the PCM1741 system clock.
During the reset period (1024 system clocks), the analog
outputs are forced to the bipolar zero level, or VCC/2. After
the reset period, the internal register is initialized in the next
1/fS period and, if SCK, BCK, and LRCK are provided
continuously, the PCM1741 provides proper analog output
with unit group delay against the input data.
SYSTEM CLOCK FREQUENCY (fSCLK) (MHz)
SAMPLING
FREQUENCY
256fS
384fS
512fS
768fS
8kHz
16kHz
32kHz
44.1kHz
48kHz
88.2kHz
96kHz
2.0480
4.0960
3.0720
6.1440
4.0960
8.1920
6.1440
12.2880
8.1920
12.2880
16.9344
18.4320
33.8688
36.8640
16.3840
22.5792
24.5760
45.1584
49.1520
24.5760
11.2896
12.2880
22.5792
24.5760
33.8688
36.8640
See Note (1)
See Note (1)
NOTE: (1) The 768fS system clock rate is not supported for fS > 64kHz.
TABLE I. System Clock Rates for Common Audio Sampling Frequencies.
tSCKH
2.0V
0.8V
“H”
System Clock
“L”
tSCKL
System clock pulse
cycle time(1)
System Clock Pulse Width HIGH tSCKH: 7ns (min)
System Clock Pulse Width LOW tSCKL: 7ns (min)
NOTE: (1) 1/256fS, 1/384fS, 1/512fS, and 1/768fS.
FIGURE 1. System Clock Input Timing.
2.4V
VDD
2.0V
1.6V
0V
Reset
Reset Removal
Internal Reset
System Clock
1024 System Clocks
Don't Care
FIGURE 2. Power-On Reset Timing.
8
PCM1741
SBAS175
held when the sampling rate clock of LRCK is changed or
SCK and/or BCK is broken at least for one clock cycle. If
SCK, BCK, and LRCK are provided continuously after this
hold condition, the internal operation will be resynchronized
automatically, less than 3/fS period. In this resynchronize
period, and following 3/fS, analog output is forced to the
bipolar zero level, or VCC/2. External resetting is not required.
AUDIO SERIAL INTERFACE
The audio serial interface for the PCM1741 is comprised of
a 3-wire synchronous serial port. It includes LRCK (pin 3),
BCK (pin 1), and DATA (pin 2). BCK is the serial audio bit
clock, and is used to clock the serial data present on DATA
into the audio interface’s serial shift register. Serial data is
clocked into the PCM1741 on the rising edge of BCK.
LRCK is the serial audio left/right word clock used to latch
serial data into the serial audio interface’s internal registers.
AUDIO DATA FORMATS AND TIMING
The PCM1741 supports industry-standard audio data formats,
including Standard, I2S, and Left-Justified, as shown in
Figure 3. Data formats are selected using the format bits,
FMT[2:0], in Control Register 20. The default data format is
24-bit left justified. All formats require Binary Two’s Comple-
ment, MSB-first audio data. See Figure 4 for a detailed timing
diagram of the serial audio interface.
Both LRCK and BCK should be synchronous to the
system clock. Ideally, it is recommended that LRCK and
BCK be derived from the system clock input, SCK. LRCK
is operated at the sampling frequency, fS. BCK may be
operated at 32, 48, or 64 times the sampling frequency (I2S
format except BCK = 32fS). Internal operation of the
PCM1741 is synchronized with LRCK. Accordingly, it is
(1) Standard Data Format: L-Channel = HIGH, R-Channel = LOW
1/fS
R-Channel
LRCK
L-Channel
BCK
(= 32, 48 or 64fS
)
16-Bit Right-Justified, BCK = 48fS or 64fS
DATA 14 15 16
1
2
3
14 15 16
1
2
3
14 15 16
MSB
LSB
MSB
LSB
16-Bit Right-Justified, BCK = 32fS
DATA 14 15 16
1
2
3
14 15 16
1
2
3
14 15 16
MSB
LSB MSB
LSB
17 18
LSB
18-Bit Right-Justified
DATA 16 17 18
1
2
3
16 17 18
1
2
MSB
LSB
MSB
20-Bit Right-Justified
DATA 18 19 20
1
2
3
18 19 20
LSB
1
2
3
18 19 20
LSB
MSB
MSB
24-Bit Right-Justified
DATA 22 23 24
1
2
3
22 23 24
1
2
3
22 23 24
LSB
MSB
LSB MSB
(2) I2S Data Format: L-Channel = LOW, R-Channel = HIGH
1/fS
LRCK
L-Channel
R-Channel
BCK
(= 48 or 64fS
)
DATA
1
2
3
N-2 N-1
N
1
2
3
N-2 N-1
N
1
2
MSB
LSB
MSB
LSB
(3) Left-Justified Data Format: L-Channel = HIGH, R-Channel = LOW
1/fS
L-Channel
LRCK
R-Channel
BCK
(= 32, 48 or 64fS
)
DATA
1
2
3
N-2 N-1
N
1
2
3
N-2 N-1
N
1
2
MSB
LSB
MSB
LSB
FIGURE 3. Audio Data Input Formats.
PCM1741
9
SBAS175
LRCK
BCK
50% of VDD
50% of VDD
tBCH
tBCL
tLB
tBCY
tBL
50% of VDD
DATA
tDS
tDH
SYMBOL
PARAMETER
MIN
MAX
UNITS
(1)
tBCY
tBCH
tBCL
tBL
BCK Pulse Cycle Time
BCK High Level Time
BCK Low Level Time
32, 48, or 64fS
35
35
10
10
10
10
ns
ns
ns
ns
ns
ns
BCK Rising Edge to LRCK Edge
LRCK Falling Edge to BCK Rising Edge
DATA Set Up Time
tLB
tDS
tDH
DATA Hold Time
NOTE: (1) fS is the sampling frequency (e.g., 44.1kHz, 48kHz, 96kHz, etc.)
FIGURE 4. Audio Interface Timing.
SERIAL CONTROL INTERFACE
the write operation. The least significant eight bits, D[7:0],
contain the data to be written to the register specified by
IDX[6:0].
The serial control interface is a 3-wire serial port that
operates asynchronously to the serial audio interface. The
serial control interface is utilized to program the on-chip
mode registers. The control interface includes MD (pin 13),
MC (pin 14), and ML (pin 15). MD is the serial data input,
used to program the mode registers, MC is the serial bit
clock, used to shift data into the control port, and ML is the
control port latch clock.
Figure 6 shows the functional timing diagram for writing the
serial control port. ML is held at a logic “1 ” state until a
register needs to be written. To start the register write cycle,
ML is set to logic “0”. Sixteen clocks are then provided on
MC, corresponding to the 16 bits of the control data word on
MD. After the sixteenth clock cycle has completed, ML is set
to logic “1” to latch the data into the indexed mode control
register.
REGISTER WRITE OPERATION
All write operations for the serial control port use 16-bit data
words. Figure 5 shows the control data word format. The
most significant bit must be a “0”. There are seven bits,
labeled IDX[6:0], that set the register index (or address) for
CONTROL INTERFACE TIMING REQUIREMENTS
See Figure 7 for a detailed timing diagram of the serial
control interface. These timing parameters are critical for
proper control port operation.
MSB
LSB
0
IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0
Register Index (or Address)
D7
D6
D5
D4
D3
D2
D1
D0
Register Data
FIGURE 5. Control Data Word Format for MDI.
ML
MC
MD
X
0
IDX6 IDX5 IDX4 IDX3 IDX2 IDX1 IDX0 D7 D6 D5
D4 D3 D2 D1 D0
X
X
0
IDX6
FIGURE 6. Register Write Operation.
10
PCM1741
SBAS175
MODE CONTROL REGISTERS
section of this data sheet. Table II lists the available mode
control functions, along with their reset default conditions
and associated register index.
User-Programmable Mode Controls
The PCM1741 includes a number of user-programmable
functions that are accessed via control registers. The regis-
ters are programmed using the Serial Control Interface that
was previously discussed in the “Serial Control Interface”
Register Map
The mode control register map is shown in Table III. Each
register includes an index (or address) indicated by the
IDX[6:0] bits.
tMHH
50% of VDD
ML
tMCH
tMCL
tMLS
tMLH
50% of VDD
MC
MD
tMCY
LSB
50% of VDD
tMDS
tMCH
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
tMCY
tMCL
tMCH
tMHH
tMLS
tMLH
tMDH
tMDS
MC Pulse Cycle Time
MC Low Level Time
MC High Level Time
ML High Level Time
100
50
ns
ns
ns
ns
ns
ns
ns
ns
50
Note (2)
20
ML Falling Edge to MC Rising Edge
ML Hold Time(1)
20
MD Hold Time
15
MD Set Up Time
20
3
NOTES: (1) MC rising edge for LSB to ML rising edge. (2)
sec (min), fS = Sampling Rate.
256 • fS
FIGURE 7. Control Interface Timing.
FUNCTION
RESET DEFAULT
CONTROL REGISTER
INDEX, IDX[6:0]
Digital Attenuation Control, 0dB to –63dB in 0.5dB Steps
Soft Mute Control
Oversampling Rate Control (64 or 128fS)
DAC Operation Control
De-Emphasis Function Control
De-Emphasis Sample Rate Selection
Audio Data Format Control
Digital Filter Roll-Off Control
Zero Flag Function Select
0dB, No Attenuation
Mute Disabled
64fS Oversampling
DAC1 and DAC2 Enabled
De-Emphasis Disabled
44.1kHz
24-Bit Left Justified
Sharp Roll-Off
L-/R-Channel Independent
Normal Phase
16 and 17
AT1[7:0], AT2[7:0]
MUT[2:0]
OVER
18
18
19
19
19
20
20
22
22
22
DAC[2:1]
DM12
DMF[1:0]
FMT[2:0]
FLT
AZRO
DREV
ZREV
Output Phase Select
Zero Flag Polarity Select
High
TABLE II. User-Programmable Mode Controls.
IDX
(B8-B14) REGISTER
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
10H
11H
12H
13H
14H
15H
16H
16
17
18
19
20
21
22
0
0
0
0
0
0
0
IDX6
IDX6
IDX6
IDX6
IDX6
IDX6
IDX6
IDX5 IDX4
IDX5 IDX4
IDX5 IDX4
IDX5 IDX4
IDX5 IDX4
IDX5 IDX4
IDX5 IDX4
IDX3 IDX2
IDX3 IDX2
IDX3 IDX2
IDX3 IDX2
IDX3 IDX2
IDX3 IDX2
IDX3 IDX2
IDX1 IDX0
IDX1 IDX0
AT17 AT16 AT15 AT14 AT13 AT12 AT11 AT10
AT27 AT26 AT25 AT24 AT23 AT22 AT21 AT20
IDX1 IDX0 RSV(1) OVER RSV(1) RSV(1) RSV(1) RSV(1) MUT2 MUT1
IDX1 IDX0 RSV(1) DMF1 DMF0 DM12 RSV(1) RSV(1) DAC2 DAC1
IDX1 IDX0 RSV(1) RSV(1) FLT RSV(1) RSV(1) FMT2 FMT1 FMT0
IDX1 IDX0 RSV(1) RSV(1) RSV(1) RSV(1) RSV(1) RSV(1) RSV(1) RSV(1)
IDX1 IDX0 RSV(1) RSV(1) RSV(1) RSV(1) RSV(1) AZRO ZREV DREV
NOTE: (1) RSV = Reserved for test operation. It should be set to “0” when in regular operation.
TABLE III. Mode Control Register Map.
PCM1741
11
SBAS175
REGISTER DEFINITIONS
B15
0
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 16
Register 17
IDX6
IDX5
IDX4
IDX3
IDX2
IDX1
IDX0
AT17 AT16
AT15
AT14
AT13
AT12 AT11 AT10
0
IDX6
IDX5
IDX4
IDX3
IDX2
IDX1
IDX0
AT27 AT26
AT25
AT24
AT23
AT22 AT21 AT20
ATx[7:0]
Digital Attenuation Level Setting
where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR (x = 2).
Default Value: 1111 1111B
Each DAC channel (VOUTL and VOUTR) includes a digital attenuator function. The attenuation level may be
set from 0dB to –63dB, in 0.5dB steps. Changes in attentuator levels are made by incrementing or
decrementing, by one step (0.5dB), for every 8/fS time interval until the programmed attenuator setting is
reached. Alternatively, the attenuator level may be set to infinite attenuation (or mute). The attenuation data
for each channel can be set individually.
The attenuation level may be set using the formula below.
Attenuation Level (dB) = 0.5 (ATx[7:0]DEC – 255)
where: ATx[7:0]DEC = 0 through 255
for: ATx[7:0]DEC = 0 through 128, the attenuator is set to infinite attenuation.
The following table shows attenuator levels for various settings.
ATx[7:0]
Decimal Value
Attenuator Level Setting
1111 1111B
1111 1110B
1111 1101B
1000 0011B
1000 0010B
1000 0001B
1000 0000B
•
255
254
253
131
130
129
128
•
0dB, No Attenuation (default)
–0.5dB
–1.0dB
–62.0dB
–62.5dB
–63.0dB
Mute
•
•
•
•
•
•
•
0000 0000B
0
Mute
B15
0
B14
IDX6
B13
B12
B11
B10
B9
IDX1
B8
B7
B6
B5
B4
B3
B2
B1
B0
Register 18
IDX5
IDX4
IDX3
IDX2
IDX0
RSV OVER
RSV
RSV
RSV
RSV MUT2 MUT1
MUTx
Soft Mute Control
Where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) and VOUTR (x = 2).
Default Value: 0
MUTx = 0
MUTx = 1
Mute Disabled (default)
Mute Enabled
The mute bits, MUT1 and MUT2, are used to enable or disable the Soft Mute function for the corresponding
DAC outputs, VOUTL and VOUTR. The Soft Mute function is incorporated into the digital attenuators. When
Mute is disabled (MUTx = 0), the attenuator and DAC operate normally. When Mute is enabled by setting
MUTx = 1, the digital attenuator for the corresponding output will be decreased from the current setting to
the infinite attenuation setting, one attenuator step (0.5dB) at a time. This provides a “pop”-free muting of the
DAC output. By setting MUTx = 0, the attenuator will be increased one step at a time to a previously
programmed attenuation level.
OVER
Oversampling Rate Control
Default Value: 0
OVER = 0
OVER = 1
64x Oversampling (default)
128x Oversampling
The OVER bit is used to control the oversampling rate of the delta-sigma DACs.
PCM1741
12
SBAS175
B15
0
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
REGISTER 19
IDX6
IDX5
IDX4
IDX3
IDX2
IDX1
IDX0
RSV DMF1 DMF0 DM12
RSV
RSV DAC2 DAC1
DACx
DAC Operation Control
where x = 1 or 2, corresponding to the DAC output VOUTL (x = 1) or VOUTR (x = 2).
Default Value: 0
DACx = 0
DACx = 1
DAC Operation Enabled (default)
DAC Operation Disabled
The DAC operation controls are used to enable and disable the DAC outputs, VOUTL and VOUTR. When
DACx = 0, the corresponding output will generate the audio waveform dictated by the data present on the
DATA pin. When DACx = 1, the corresponding output will be set to the bipolar zero level, or VCC/2.
DM12
Digital De-Emphasis Function Control
Default Value: 0
DM12 = 0
DM12 = 1
De-Emphasis Disabled (default)
De-Emphasis Enabled
The DM12 bit is used to enable or disable the Digital De-Emphasis function. Refer to the Typical Performance
Curves of this data sheet for more information.
DMF[1:0]
Sampling Frequency Selection for the De-Emphasis Function
Default Value: 00
DMF[1:0]
De-Emphasis Same Rate Selection
00
01
10
11
44.1kHz (default)
48kHz
32kHz
Reserved
The DMF[1:0] bits are used to select the sampling frequency used for the Digital De-Emphasis function when
it is enabled.
B15
0
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
REGISTER 20
IDX6
IDX5
IDX4
IDX3
IDX2
IDX1
IDX0
RSV
RSV
FLT
RSV
RSV
FMT2 FMT1 FMT0
FMT[2:0] Audio Interface Data Format
Default Value: 101
The FMT[2:0] bits are used to select the data format for the serial audio interface. The following table shows
the available format options.
FMT[2:0]
Audio Data Format Selection
000
001
010
011
100
101
110
111
24-Bit Standard Format, Right-Justified Data
20-Bit Standard Format, Right-Justified Data
18-Bit Standard Format, Right-Justified Data
16-Bit Standard Format, Right-Justified Data
I2S Format, 16- to 24-bits
Left-Justified Format, 16- to 24-Bits (default)
Reserved
Reserved
PCM1741
13
SBAS175
Register 20 (Cont.)
FLT
Digital Filter Roll-Off Control
Default Value: 0
FLT = 0
FLT = 1
Sharp Roll-Off (default)
Slow Roll-Off
The FLT bit allows the user to select the digital filter roll-off that is best suited to their application. Two
filter roll-off sections are available: Sharp or Slow. The filter responses for these selections are shown in
the Typical Performance Curves section of this data sheet.
B15
0
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
REGISTER 22
IDX6
IDX5
IDX4
IDX3
IDX2
IDX1
IDX0
RSV
RSV
RSV
RSV
RSV
AZRO ZREV DREV
DREV
Output Phase Select
Default Value: 0
DREV = 0
DREV = 1
Normal Output (default)
Inverted Output
The DREV bit is used to set the output phase of VOUTL and VOUTR.
ZREV
Zero Flag Polarity Select
Default Value: 0
ZREV = 0
ZREV = 1
Zero Flag Pins HIGH at a Zero Detect (default)
Zero Flag Pins LOW at a Zero Detect
The ZREV bit allows the user to select the active polarity of Zero Flag pins.
AZRO
Zero Flag Function Select
Default Value: 0
AZRO = 0
AZRO = 1
L-/R-Channel Independent Zero Flag (default)
L-/R-Channel Common Zero Flag
Register22 (Cont.)
The AZRO bit allows the user to select the function of Zero Flag pins.
AZRO = 0:
Pin11: ZEROR; Zero Flag Output for R-Channel
Pin12: ZEROL; Zero Flag Output for L-Channel
AZRO = 1:
Pin11: ZEROA; Zero Flag Output for L-/R-Channel
Pin12: NA; No Assign
PCM1741
14
SBAS175
ANALOG OUTPUTS
ANALOG FILTER PERFORMANCE
(100Hz-10MHz)
The PCM1741 includes two independent output channels:
VOUTL and VOUTR. These are unbalanced outputs, each capable
of driving 2.05Vp-p typical into a 5kΩ AC-coupled load. The
internal output amplifiers for VOUTL and VOUTR are biased to the
DC common-mode (or bipolar zero) voltage, equal to VCC/2.
0
–10
–20
–30
–40
–50
–60
The output amplifiers include an RC continuous-time filter that
helps to reduce the out-of-band noise energy present at the
DAC outputs, due to the noise shaping characteristics of the
PCM1741’s delta-sigma DACs. The frequency response of this
filter is shown in Figure 8. By itself, this filter is not enough to
attenuate the out-of-band noise to an acceptable level for many
applications, therefore, an external low-pass filter is required to
provide sufficient out-of-band noise rejection. Further discus-
sion of DAC post-filter circuits is provided in the Applications
Information section of this data sheet.
0.1
1
10
100
1K
10K
Frequency (kHz)
FIGURE 8. Output Filter Frequency Response.
VCOM OUTPUT
nominally biased to a DC voltage level equal to VCC/2. This
pin may be used to bias external circuits. Figure 9 shows an
example of using the VCOM pin for external biasing applica-
tions.
One unbuffered common-mode voltage output pin, VCOM
(pin 10), is brought out for decoupling purposes. This pin is
R2
A
V = –1, where AV = –
R2
C1
R1
VCC
PCM1741
10µF
R1
R3
2
3
VOUT
x
+
1
1/2
OPA2342
Filtered
Output
C2
VCOM
+
10µF
x = L or R
(a) Using VCOM to Bias a Single-Supply Filter Stage
VCC
PCM1741
Buffered
VCOM
OPA342
VCOM
+
10µF
(b) Using a Voltage Follower to Buffer VCOM when Biasing Multiple Nodes
FIGURE 9. Biasing External Circuits Using the VCOM Pin.
PCM1741
15
SBAS175
ZERO FLAGS
POWER SUPPLIES AND GROUNDING
The PCM1741 requires a +3.3V analog supply (VCC) and a
+3.3V digital supply (VDD). The +3.3V supply (VCC) is used to
power the DAC analog and output filter circuitry, while the
+3.3V (VDD) supply is used to power the digital filter and serial
Zero Detect Condition
Zero Detection for each output channel is independent from
the other. If the data for a given channel remains at a “0”
level for 1024 sample periods (or LRCK clock periods), a
Zero Detect condition exists for that channel.
interface circuitry. For best performance, the +3.3V (VDD
)
supply should be derived from the +3.3V (VCC) supply using a
linear regulator, as shown in Figure 11.
Zero Output Flags
Given that a Zero Detect condition exists for one or more
channels, the Zero Flag pins for those channels will be set to
a logic “1” state. There are Zero Flag pins for each channel:
ZEROL (pin 12) and ZEROR (pin 11). These pins can be used
to operate external mute circuits, or used as status indicators
for a microcontroller, audio signal processor, or other digitally
controlled functions.
Proper power-supply bypassing is shown in Figure 10. The
10µF capacitors should be tantalum or aluminum electrolytic,
while the 0.1µF capacitors are ceramic (X7R type is recom-
mended for surface-mount applications).
R2
A
V ≈ –
The active polarity of Zero Flag output can be inverted by
setting the ZREV bit of Control Register 22 to “1”. The reset
default is active high output, or ZREV = 0.
R1
C1
2
R2
R1
R3
VIN
R4
1
VOUT
The L-channel and R-channel common Zero Flag can be
selected by setting the AZRO bit of Control Register 22 to “1”.
The reset default is L-channel and R-channel independent
Zero Flag, or AZRO = 0.
OPA2134
3
C2
FIGURE 10. Dual-Supply Filter Circuit.
APPLICATIONS INFORMATION
CONNECTION DIAGRAMS
DAC OUTPUT FILTER CIRCUITS
Delta-sigma DACs utilize noise-shaping techniques to im-
prove in-band Signal-to-Noise Ratio (SNR) performance at
the expense of generating increased out-of-band noise above
the Nyquist Frequency, or fS/2. The out-of-band noise must
be low-pass filtered in order to provide the optimal converter
performance. This is accomplished by a combination of
on-chip and external low-pass filtering.
A basic connection diagram is shown in Figure 11, with the
necessary power-supply bypassing and decoupling compo-
nents. Texas Instruments recommends using the component
values shown in Figure 11 for all designs.
The use of series resistors (22Ω to 100Ω) are recommended
for the SCK, LRCK, BCK, and DATA inputs. The series
resistor combines with stray PCB and device input capaci-
tance to form a low-pass filter that reduces high-frequency
noise emissions and helps to dampen glitches and ringing
present on clock and data lines.
Figures 9(a) and 10 show the recommended external low-
pass active filter circuits for single- and dual-supply applica-
tions. These circuits are second-order Butterworth filters
System Clock
SCK 16
1
2
3
4
5
6
7
8
BCK
PCM
Audio Data
Input
DATA
LRCK
DGND
VDD
ML 15
Mode
MC 14
Control
MD 13
+
+
10µF
10µF
+3.3V
Regulator
ZEROL/NA 12
Zero Mute
Control
VCC
ZEROR/ZEROA 11
VOUT
L
VCOM 10
10µF
V
OUTR
AGND
9
+3.3V
Post LPF
Post LPF
L-Chan OUT
R-Chan OUT
FIGURE 11. Basic Connection Diagram.
16
PCM1741
SBAS175
using a Multiple FeedBack (MFB) circuit arrangement that
reduces sensitivity to passive component variations over
frequency and temperature. For more information regarding
MFB active filter design, please refer to Burr-Brown Appli-
cations Bulletin #34 AB-034 (SBFA001), available from our
web site at http://www.ti.com.
PCB LAYOUT GUIDELINES
A typical PCB floor plan for the PCM1741 is shown in
Figure 12. A ground plane is recommended, with the analog
and digital sections being isolated from one another using a
split or cut in the circuit board. The PCM1741 should be
oriented with the digital I/O pins facing the ground plane
split/cut to allow for short, direct connections to the digital
audio interface and control signals originating from the
digital section of the board.
Since the overall system performance is defined by the
quality of the DACs and their associated analog output
circuitry, high-quality audio op amps are recommended for
the active filters. The OPA2353 and OPA2134 dual op amps
from Texas Instruments are recommended for use with the
PCM1741, see Figures 9(a) and 10.
Digital Power
Analog Power
+VD
DGND
AGND +3.3V
+VS –VS
REG
VCC
VDD
Digital Logic
and
Output
DGND
Circuits
Audio
Processor
PCM1741
Digital
Ground
AGND
Analog
Ground
DIGITAL SECTION
ANALOG SECTION
Return Path for Digital Signals
FIGURE 12. Recommended PCB Layout.
PCM1741
17
SBAS175
Separate power supplies are recommended for the digital
and analog sections of the board. This prevents the switching
noise present on the digital supply from contaminating the
analog power supply and degrading the dynamic perfor-
mance of the PCM1741. In cases where a common +3.3V
supply must be used for the analog and digital sections, an
inductance (RF choke, ferrite bead) should be placed be-
tween the analog and digital +3.3V supply connections to
avoid coupling of the digital switching noise into the analog
circuitry. Figure 13 shows the recommended approach for
single-supply applications.
THEORY OF OPERATION
The delta-sigma section of the PCM1741 is based on an
8-level amplitude quantizer and a fourth-order noise shaper. This
section converts the oversampled input data to 8-level delta-sigma
format. A block diagram of the 8-level delta-sigma modulator is
shown in Figure 14. This 8-level delta-sigma modulator has the
advantage of stability and clock jitter sensitivity over the typical
one-bit (2-level) delta-sigma modulator. The combined
oversampling rate of the delta-sigma modulator and the interpo-
lation filter is 64fS.
Power Supplies
RF Choke or Ferrite Bead
+3.3V AGND +VS –VS
REG
VCC
VDD
VDD
Output
Circuits
DGND
PCM1741
AGND
Common
Ground
DIGITAL SECTION
ANALOG SECTION
FIGURE 13. Single-Supply PCB Layout.
–
+
Z–1
Z–1
Z–1
Z–1
8fS
+
+
+
+
+
8-Level Quantizer
64fS
FIGURE 14. 8-Level Delta-Sigma Modulator.
PCM1741
18
SBAS175
QUANTIZATION NOISE SPECTRUM
(64x Oversampling)
QUANTIZATION NOISE SPECTRUM
(128x Oversampling)
0
–20
0
–20
–40
–40
–60
–60
–80
–80
–100
–120
–140
–160
–180
–100
–120
–140
–160
–180
0
1
2
3
4
5
6
7
8
0
1
2
3
4
5
6
7
8
Frequency (fS)
Frequency (fS)
FIGURE 15. Quantization Noise Spectrum.
The theoretical quantization noise performance of the
8-level delta-sigma modulator is shown in Figure 15. The en-
hanced multilevel delta-sigma architecture also has advantages
for input clock jitter sensitivity due to the multilevel quantizer,
with the simulated jitter sensitivity, as shown in Figure 16.
KEY PERFORMANCE PARAMETERS
AND MEASUREMENT
This section provides information on how to measure key
dynamic performance parameters for the PCM1741. In all
cases, an Audio Precision System Two Cascade or equivalent
audio measurement system is utilized to perform the testing.
JITTER DEPENDENCE (64x Oversampling)
125
TOTAL HARMONIC DISTORTION + NOISE
120
115
110
105
100
95
Total Harmonic Distortion + Noise (THD+N) is a significant
figure of merit for audio DACs, since it takes into account
both harmonic distortion and all noise sources within a
specified measurement bandwidth. The true rms value of the
distortion and noise is referred to as THD+N. Figure 17
shows the test setup for THD+N measurements.
For the PCM1741, THD+N is measured with a full-scale,
1kHz digital sine wave as the test stimulus at the input of the
DAC. The digital generator is set to a 24-bit audio word
length and a sampling frequency of 44.1kHz or 96kHz. The
digital generator output is taken from the unbalanced
S/PDIF connector of the measurement system. The S/PDIF
90
0
100
200
300
400
500
600
Jitter (ps)
FIGURE 16. Jitter Sensitivity.
Evaluation Board
DEM-DAI1741
2nd-Order
Low-Pass
Filter
S/PDIF
Receiver
PCM1741
f–3dB = 54kHz or 108kHz
Analyzer
and
Display
20kHz
Apogee
Filter
Digital
Generator
S/PDIF
Output
Band Limit
Notch Filter
fC = 1kHz
0dBFS,
rms Mode
HPF = 22Hz
LPF = 30kHz
1kHz Sine Wave
FIGURE 17. Test Setup for THD+N Measurements.
PCM1741
19
SBAS175
data is transmitted via a coaxial cable to the digital audio
receiver on the DEM-DAI1741 demo board. The receiver is
then configured to output 24-bit data in either I2S or left-
justified data format. The DAC audio interface format is
programmed to match the receiver output format. The ana-
log output is then taken from the DAC post filter and
connected to the analog analyzer input of the measurement
system. The analog input is band limited using filters resi-
dent in the analyzer. The resulting THD+N is measured by
the analyzer and displayed by the measurement system.
The measurement setup for the dynamic range measurement
is shown in Figure 18, and is similar to the THD+N test
setup discussed previously. The differences include the band
limit filter selection, the additional A-Weighting filter, and
the –60dBFS input level.
IDLE CHANNEL SIGNAL-TO-NOISE RATIO
The SNR test provides a measure of the noise floor of the
DAC. The input to the DAC is all “0”s data, and the DAC’s
Infinite Zero Detect Mute function must be disabled (default
condition at power up for the PCM1741). This ensures that
the delta-sigma modulator output is connected to the output
amplifier circuit so that idle tones (if present) can be ob-
served and effect the SNR measurement. The dither function
of the digital generator must also be disabled to ensure an all
“0”s data stream at the input of the DAC. The measurement
setup for SNR is identical to that used for dynamic range,
with the exception of the input signal level (see the notes
provided in Figure 18).
DYNAMIC RANGE
Dynamic range is specified as A-Weighted, THD+N mea-
sured with a –60dBFS, 1kHz digital sine wave stimulus at
the input of the DAC. This measurement is designed to give
a good indicator of how the DAC will perform given a low-
level input signal.
Evaluation Board
DEM-DAI1741
2nd-Order
PCM1741(1)
S/PDIF
Receiver
Low-Pass
Filter
f–3dB = 54kHz
Analyzer
and
Display
Digital
Generator
A-Weight
Filter(1)
S/PDIF
Output
Band Limit
Notch Filter
C = 1kHz
0% Full-Scale,
Dither Off (SNR)
–60dBFS,
rms Mode
HPF = 22Hz
LPF = 22kHz
Option = A-Weighting(2)
f
1kHz Sine Wave
(Dynamic Range)
NOTES: (1) Infinite Zero Detect Mute disabled.
(2) Results without A-Weighting will be approxi-
mately 3dB worse.
FIGURE 18. Test Setup for Dynamic Range and SNR Measurements.
PCM1741
20
SBAS175
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jul-2008
PACKAGING INFORMATION
Orderable Device
PCM1741E
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
SSOP/
QSOP
DBQ
16
16
16
16
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
PCM1741E/2K
PCM1741E/2KG4
PCM1741EG4
SSOP/
QSOP
DBQ
DBQ
DBQ
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SSOP/
QSOP
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SSOP/
QSOP
75 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) W1 (mm)
(mm) (mm) Quadrant
PCM1741E/2K
SSOP/
QSOP
DBQ
16
2000
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SSOP/QSOP DBQ 16
SPQ
Length (mm) Width (mm) Height (mm)
346.0 346.0 29.0
PCM1741E/2K
2000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
Logic
Military
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated
相关型号:
PCM1741/E2K
+3.3V Single-Supply, 24-Bit, 96kHz Sampling Enhanced Multilevel, Delta-Sigma, Audio DIGITAL-TO-ANALOG CONVERTER
BB
PCM1741E
+3.3V Single-Supply, 24-Bit, 96kHz Sampling Enhanced Multilevel, Delta-Sigma, Audio DIGITAL-TO-ANALOG CONVERTER
BB
PCM1742
24-Bit, 192kHz Sampling Enhanced Multilevel, Delta-Sigma, Audio DIGITAL-TO-ANALOG CONVERTER
BB
PCM1742E
24-Bit, 192kHz Sampling Enhanced Multilevel, Delta-Sigma, Audio DIGITAL-TO-ANALOG CONVERTER
BB
PCM1742E
24-Bit, 192-kHz Sampling, Enhanced Multilevel, Delta-Sigma, Audio Digital-to-Analog Converter
TI
PCM1742E/2K
24-Bit, 192kHz Sampling Enhanced Multilevel, Delta-Sigma, Audio DIGITAL-TO-ANALOG CONVERTER
BB
PCM1742E/2K
24-Bit, 192-kHz Sampling, Enhanced Multilevel, Delta-Sigma, Audio Digital-to-Analog Converter
TI
PCM1742E/2KG4
24-Bit, 192-kHz Sampling, Enhanced Multilevel, Delta-Sigma, Audio Digital-to-Analog Converter
TI
©2020 ICPDF网 联系我们和版权申明