SN74ABT16244ADL [TI]
16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS; 16位缓冲器/驱动器,具有三态输出型号: | SN74ABT16244ADL |
厂家: | TEXAS INSTRUMENTS |
描述: | 16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS |
文件: | 总12页 (文件大小:184K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SN54ABT16244, SN74ABT16244A
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
www.ti.com
SCBS073H–SEPTEMBER 1991–REVISED AUGUST 2005
FEATURES
SN54ABT16244. . . WD PACKAGE
SN74ABT16244A. . . DGG, DGV, OR DL PACKAGE
(TOP VIEW)
•
•
•
•
•
•
Members of the Texas Instruments
Widebus™ Family
State-of-the-Art EPIC-IIB™ BiCMOS Design
Significantly Reduces Power Dissipation
1
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1OE
1Y1
1Y2
GND
1Y3
1Y4
2OE
1A1
1A2
GND
1A3
1A4
2
Latch-Up Performance Exceeds 500 mA Per
JESD 70
3
4
Typical VOLP (Output Ground Bounce) <1 V
at VCC = 5 V, TA = 25°C
5
6
Distributed VCC and GND Pin Configuration
Minimizes High-Speed Switching Noise
7
V
CC
V
CC
8
2Y1
2Y2
GND
2Y3
2Y4
3Y1
3Y2
GND
3Y3
3Y4
2A1
2A2
GND
2A3
2A4
3A1
3A2
GND
3A3
3A4
Flow-Through Architecture Optimizes PCB
Layout
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
•
•
High-Drive Outputs (–32-mA IOH, 64-mA IOL)
Package Options Include Plastic 300-mil
Shrink Small-Outline (DL), Thin Shrink
Small-Outline (DGG), and Thin Very
Small-Outline (DGV) Packages and 380-mil
Fine-Pitch Ceramic Flat (WD) Package
Using 25-mil Center-to-Center Spacings
V
CC
V
CC
4Y1
4Y2
GND
4Y3
4Y4
4OE
4A1
4A2
GND
4A3
4A4
3OE
DESCRIPTION
The SN54ABT16244 and SN74ABT16244A are 16-bit
buffers and line drivers designed specifically to
improve both the performance and density of 3-state
memory address drivers, clock drivers, and
bus-oriented receivers and transmitters. These
devices can be used as four 4-bit buffers, two 8-bit
buffers, or one 16-bit buffer. These devices provide
true outputs and symmetrical OE (active-low
output-enable) inputs.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN54ABT16244 is characterized for operation over the full military temperature range of –55°C to 125°C.
The SN74ABT16244A is characterized for operation from –40°C to 85°C.
FUNCTION TABLE
(EACH BUFFER)
INPUTS
OUTPUT
Y
OE
A
H
L
L
L
H
L
H
X
Z
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus, EPIC-IIB are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Copyright © 1991–2005, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
On products compliant to MIL-PRF-38535, all parameters are
Instruments standard warranty. Production processing does not
tested unless otherwise noted. On all other products, production
necessarily include testing of all parameters.
processing does not necessarily include testing of all parameters.
SN54ABT16244, SN74ABT16244A
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
www.ti.com
SCBS073H–SEPTEMBER 1991–REVISED AUGUST 2005
LOGIC SYMBOL(1)
1
1OE
EN1
EN2
EN3
EN4
48
2OE
25
3OE
24
4OE
47
1A1
46
2
3
1
1
1
1
1
2
3
4
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
3Y1
3Y2
3Y3
3Y4
4Y1
4Y2
4Y3
4Y4
1A2
44
5
1A3
43
6
1A4
41
8
2A1
40
9
2A2
38
11
12
13
14
16
17
19
20
22
23
2A3
37
2A4
36
3A1
35
3A2
33
3A3
32
3A4
30
4A1
29
4A2
27
4A3
26
4A4
(1) This symbol is in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
2
SN54ABT16244, SN74ABT16244A
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
www.ti.com
SCBS073H–SEPTEMBER 1991–REVISED AUGUST 2005
LOGIC DIAGRAM (POSITIVE LOGIC)
1
25
36
35
1OE
1A1
3OE
3A1
47
46
2
3
5
6
13
14
16
17
1Y1
1Y2
1Y3
1Y4
3Y1
3Y2
3Y3
3Y4
1A2
1A3
1A4
3A2
3A3
3A4
44
43
33
32
48
41
24
30
2OE
2A1
4OE
4A1
8
9
19
20
22
23
2Y1
2Y2
2Y3
2Y4
4Y1
4Y2
4Y3
4Y4
40
38
37
29
27
26
2A2
2A3
2A4
4A2
4A3
4A4
11
12
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.5
–0.5
–0.5
MAX UNIT
VCC
VI
Supply voltage range
Input voltage range(2)
7
7
V
V
V
VO
Voltage range applied to any output in the high or power-off state
5.5
96
SN54ABT16244
SN74ABT16244A
VI < 0
IO
Current into any output in the low state
mA
128
IIK
Input clamp current
Output clamp current
–18 mA
–50 mA
89
IOK
VO < 0
DGG package
DGV package
DL package
θJA
Package thermal impedance(3)
93 °C/W
94
Tstg
Storage temperature range
–65
150
°C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability
(2) The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
(3) The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD 51.
3
SN54ABT16244, SN74ABT16244A
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
www.ti.com
SCBS073H–SEPTEMBER 1991–REVISED AUGUST 2005
Recommended Operating Conditions(1)
SN54ABT16244 SN74ABT16244A
UNIT
MIN
4.5
2
MAX
MIN
4.5
2
MAX
VCC
VIH
VIL
Supply voltage
5.5
5.5
V
V
High-level input voltage
Low-level input voltage
Input voltage
0.8
VCC
–24
48
0.8
VCC
–32
64
V
VI
0
0
V
IOH
IOL
High-level output current
Low-level output current
Input transition rise or fall rate
Operating free-air temperature
mA
mA
∆t/∆v
TA
Outputs enabled
10
10 ns/V
–55
125
–40
85
°C
(1) All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
Electrical Characteristics
over recommended operating free-air temperature range (unless otherwise noted)
TA = 25°C(1)
MIN TYP(2)
SN54ABT16244
SN74ABT16244A
PARAMETER
VIK
TEST CONDITIONS
UNIT
MAX
MIN
MAX
MIN
MAX
VCC = 4.5 V,
II = –18 mA
IOH = –3 mA
IOH = –3 mA
IOH = –24 mA
IOH = –32 mA
IOL = 48 mA
IOL = 64 mA
–1.2
–1.2
–1.2
V
VCC = 4.5 V,
VCC = 5 V,
2.5
3
2.5
3
2.5
3
VOH
V
2
2(3)
2
VCC = 4.5 V
VCC = 4.5 V
2
0.55
0.55
VOL
V
0.55(3)
0.55
Vhys
II
100
mV
µA
µA
µA
µA
VCC = 5.5 V, VI = VCC or GND
±1
10(4)
–10(4)
±1
10
±1
10(4)
–10(4)
IOZH
IOZL
Ioff
VCC = 5.5 V,
VCC = 5.5 V,
VCC = 0,
VO = 2.7 V
VO = 0.5 V
–10
VI or VO ≤ 5.5 V
±100
±100
VCC = 5.5 V,
VO = 5.5 V
ICEX
Outputs high
50
50
50
µA
(5)
IO
VCC = 5.5 V,
VO = 2.5 V
–50
–100
–180
3
–50
–180
2
–50
–180
3
mA
Outputs high
Outputs low
VCC = 5.5 V,
IO = 0,
VI = VCC or GND
ICC
32
32
2
32
mA
mA
Outputs disabled
Outputs enabled
3
3
VCC = 5.5 V,
0.05
1.5
0.05
Data
inputs
One input at 3.4 V,
Other inputs at
VCC or GND
Outputs disabled
0.05
0.05
1
0.05
0.05
(6)
∆ICC
Control
inputs
VCC = 5.5 V, One input at 3.4 V,
Other inputs at VCC or GND
1.5
Ci
VI = 2.5 V or 0.5 V
VO = 2.5 V or 0.5 V
3
6
pF
pF
Co
(1) Characteristics for TA = 25°C apply to the SN74ABT16244A only.
(2) All typical values are at VCC = 5 V.
(3) On products compliant to MIL-PRF-38535, this parameter does not apply.
(4) This data-sheet limit may vary among suppliers.
(5) Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
(6) This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND.
4
SN54ABT16244, SN74ABT16244A
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
www.ti.com
SCBS073H–SEPTEMBER 1991–REVISED AUGUST 2005
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF
(unless otherwise noted) (see Figure 1 )
SN54ABT16244
VCC = 5 V,
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
UNIT
TA = 25°C
TYP
2.3
MIN
MAX
MIN
0.7
0.5
0.7
0.9
1.7
1.5
MAX
3.2
3.7
4
tPLH
tPHL
tPZH
tPZL
tPHZ
tPLZ
0.7
0.5
0.7
0.9
1.7
1.5
3.6
4.2
4.9
6.5
6
A
Y
Y
Y
ns
ns
ns
2.6
3
OE
OE
3.2
5.5
5
3.6
2.9
4.7
5.7
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF
(unless otherwise noted) (see Figure 1 )
SN74ABT16244A
VCC = 5 V,
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
UNIT
TA = 25°C
TYP
2.3
MIN
MAX
MIN
1
MAX
3.2
3.7
3.8
4
tPLH
tPHL
tPZH
tPZL
tPHZ
tPLZ
1
1
1
1
1
1
3.5
4.1
4.8
4.8
4.8
4.1
A or B
OE
Y
Y
Y
ns
ns
ns
1
2.6
1
3
1
3.2
1
3.6
4.4
3.7
OE
1
2.9
5
SN54ABT16244, SN74ABT16244A
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
www.ti.com
SCBS073H–SEPTEMBER 1991–REVISED AUGUST 2005
PARAMETER MEASUREMENT INFORMATION
7 V
Open
TEST
/t
S1
S1
500 Ω
From Output
Under Test
t
Open
7 V
PLH PHL
GND
t
/t
PLZ PZL
C = 50 pF
(see Note A)
t
/t
Open
L
PHZ PZH
500 Ω
3 V
0 V
LOAD CIRCUIT
Timing Input
Data Input
1.5 V
t
w
t
t
h
su
3 V
0 V
3 V
Input
1.5 V
1.5 V
1.5 V
1.5 V
0 V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3 V
0 V
3 V
0 V
Output
Control
1.5 V
1.5 V
1.5 V
1.5 V
Input
t
PZL
t
t
t
PHL
PLH
t
PLZ
Output
Waveform 1
S1 at 7 V
3.5 V
V
V
OH
1.5 V
1.5 V
1.5 V
1.5 V
Output
V
V
+ 0.3 V
− 0.3 V
OL
V
OL
OL
(see Note B)
t
PHZ
t
PHL
PLH
t
PZH
Output
Waveform 2
S1 at Open
(see Note B)
V
OH
V
V
OH
OH
1.5 V
1.5 V
Output
≈ 0 V
OL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. C includes probe and jig capacitance.
L
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, Z = 50 Ω, t ≤ 2.5 ns, t ≤ 2.5 ns.
O
r
f
D. The outputs are measured one at a time, with one transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
6
PACKAGE OPTION ADDENDUM
www.ti.com
26-Sep-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
5962-9317401MXA
ACTIVE
ACTIVE
CFP
WD
48
48
1
TBD
Call TI
Level-NC-NC-NC
74ABT16244ADGGRG4
TSSOP
DGG
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
74ABT16244ADGVRE4
SN74ABT16244ADGGR
SN74ABT16244ADGVR
SN74ABT16244ADL
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
TVSOP
TSSOP
TVSOP
SSOP
SSOP
SSOP
SSOP
CFP
DGV
DGG
DGV
DL
48
48
48
48
48
48
48
48
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SN74ABT16244ADLG4
SN74ABT16244ADLR
SN74ABT16244ADLRG4
SNJ54ABT16244WD
DL
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
DL
1000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
DL
1000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
WD
1
TBD
Call TI
Level-NC-NC-NC
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan
-
The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS
&
no Sb/Br)
-
please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MCFP010B – JANUARY 1995 – REVISED NOVEMBER 1997
WD (R-GDFP-F**)
CERAMIC DUAL FLATPACK
48 LEADS SHOWN
0.120 (3,05)
0.075 (1,91)
0.009 (0,23)
0.004 (0,10)
1.130 (28,70)
0.870 (22,10)
0.370 (9,40)
0.250 (6,35)
0.390 (9,91)
0.370 (9,40)
0.370 (9,40)
0.250 (6,35)
1
48
0.025 (0,635)
A
0.014 (0,36)
0.008 (0,20)
24
25
NO. OF
LEADS**
48
56
0.740
0.640
(16,26) (18,80)
A MAX
A MIN
0.610 0.710
(15,49) (18,03)
4040176/D 10/97
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only
E. Falls within MIL STD 1835: GDFP1-F48 and JEDEC MO-146AA
GDFP1-F56 and JEDEC MO-146AB
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,23
0,13
M
0,07
0,40
24
13
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–ā8°
0,75
1
12
0,50
A
Seating Plane
0,08
0,15
0,05
1,20 MAX
PINS **
14
16
20
24
38
48
56
DIM
A MAX
A MIN
3,70
3,50
3,70
3,50
5,10
4,90
5,10
4,90
7,90
7,70
9,80
9,60
11,40
11,20
4073251/E 08/00
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
D. Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MSSO001C – JANUARY 1995 – REVISED DECEMBER 2001
DL (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0.025 (0,635)
48
0.0135 (0,343)
0.008 (0,203)
0.005 (0,13)
M
25
0.010 (0,25)
0.005 (0,13)
0.299 (7,59)
0.291 (7,39)
0.420 (10,67)
0.395 (10,03)
Gage Plane
0.010 (0,25)
0°–ā8°
1
24
0.040 (1,02)
0.020 (0,51)
A
Seating Plane
0.004 (0,10)
0.008 (0,20) MIN
PINS **
0.110 (2,79) MAX
28
48
0.630
56
DIM
0.380
(9,65)
0.730
A MAX
A MIN
(16,00) (18,54)
0.370
(9,40)
0.620
0.720
(15,75) (18,29)
4040048/E 12/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MO-118
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
M
0,08
0,50
48
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
0,25
1
24
0°–8°
A
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
48
56
64
DIM
A MAX
12,60
12,40
14,10
13,90
17,10
16,90
A MIN
4040078/F 12/97
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明