SN74AHC16240DLG4 [TI]
AHC/VHC/H/U/V SERIES, QUAD 4-BIT DRIVER, INVERTED OUTPUT, PDSO48, GREEN, PLASTIC, SSOP-48;型号: | SN74AHC16240DLG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | AHC/VHC/H/U/V SERIES, QUAD 4-BIT DRIVER, INVERTED OUTPUT, PDSO48, GREEN, PLASTIC, SSOP-48 驱动 光电二极管 输出元件 逻辑集成电路 |
文件: | 总14页 (文件大小:381K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SN54AHC16240, SN74AHC16240
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS326G – MARCH 1996 – REVISED JANUARY 2000
SN54AHC16240 . . . WD PACKAGE
SN74AHC16240 . . . DGG, DGV, OR DL PACKAGE
(TOP VIEW)
Members of the Texas Instruments
Widebus Family
EPIC (Enhanced-Performance Implanted
CMOS) Process
1OE
1Y1
1Y2
GND
1Y3
1Y4
1
2
3
4
5
6
7
8
9
48 2OE
47 1A1
46 1A2
45 GND
44 1A3
43 1A4
Operating Range 2-V to 5.5-V V
CC
Distributed V
High-Speed Switching Noise
and GND Pins Minimize
CC
Flow-Through Architecture Optimizes PCB
Layout
V
42
V
CC
CC
Latch-Up Performance Exceeds 250 mA Per
JESD 17
2Y1
2Y2
41 2A1
40 2A2
39 GND
38 2A3
37 2A4
36 3A1
35 3A2
34 GND
33 3A3
32 3A4
Package Options Include Plastic Shrink
Small-Outline (DL), Thin Shrink
Small-Outline (DGG), and Thin Very
Small-Outline (DGV) Packages and 380-mil
Fine-Pitch Ceramic Flat (WD) Package
Using 25-mil Center-to-Center Spacings
GND 10
2Y3 11
2Y4 12
3Y1 13
3Y2 14
GND 15
3Y3 16
3Y4 17
description
V
18
31
V
The ’AHC16240 devices are 16-bit buffers and
line drivers designed specifically to improve the
performance and density of 3-state memory
address drivers, clock drivers, and bus-oriented
receivers and transmitters.
CC
CC
4Y1 19
4Y2 20
GND 21
4Y3 22
30 4A1
29 4A2
28 GND
27 4A3
23
24
26
25
4Y4
4OE
4A4
3OE
These devices can be used as four 4-bit buffers,
two8-bitbuffers, orone16-bitbuffer. Theyprovide
inverting outputs and symmetrical active-low
output-enable (OE) inputs.
To ensure the high-impedance state during power up or power down, OE should be tied to V through a pullup
CC
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN54AHC16240 is characterized for operation over the full military temperature range of –55°C to 125°C.
The SN74AHC16240 is characterized for operation from –40°C to 85°C.
FUNCTION TABLE
(each 4-bit buffer/driver)
INPUTS
OUTPUT
Y
OE
A
H
L
L
L
L
H
Z
H
X
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
EPIC and Widebus are trademarks of Texas Instruments Incorporated.
Copyright 2000, Texas Instruments Incorporated
UNLESS OTHERWISE NOTED this document contains PRODUCTION
DATA information current as of publication date. Products conform to
specifications per the terms of Texas Instruments standard warranty.
Production processing does not necessarily include testing of all
parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN54AHC16240, SN74AHC16240
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS326G – MARCH 1996 – REVISED JANUARY 2000
†
logic symbol
1
1OE
EN1
EN2
EN3
EN4
48
2OE
25
3OE
24
4OE
47
1A1
46
2
3
1
1
1
1
2
3
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
3Y1
3Y2
3Y3
3Y4
4Y1
4Y2
4Y3
4Y4
1A2
44
5
1A3
43
6
1A4
41
8
2A1
40
9
2A2
38
11
12
13
14
16
17
19
20
22
23
2A3
37
2A4
36
3A1
35
3A2
33
3A3
32
3A4
30
4A1
29
1
4
4A2
27
4A3
26
4A4
†
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN54AHC16240, SN74AHC16240
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS326G – MARCH 1996 – REVISED JANUARY 2000
logic diagram (positive logic)
1
25
36
1OE
3OE
3A1
47
2
3
5
6
13
1A1
1Y1
1Y2
1Y3
1Y4
3Y1
46
35
33
32
14
1A2
3A2
3A3
3A4
3Y2
44
16
1A3
3Y3
43
17
1A4
3Y4
48
24
30
2OE
4OE
4A1
41
8
9
19
2A1
2Y1
2Y2
2Y3
2Y4
4Y1
40
29
27
26
20
2A2
4A2
4A3
4A4
4Y2
38
11
12
22
2A3
4Y3
37
23
2A4
4Y4
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
CC
Input voltage range, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V
I
Output voltage range, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to V
+ 0.5 V
O
CC
Input clamp current, I (V < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –20 mA
IK
I
Output clamp current, I
(V < 0 or V > V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
OK
O O CC
Continuous output current, I (V = 0 to V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA
Continuous current through each V
Package thermal impedance, θ (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W
O
O
CC
or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±75 mA
CC
JA
DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W
DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63°C/W
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51.
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN54AHC16240, SN74AHC16240
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS326G – MARCH 1996 – REVISED JANUARY 2000
recommended operating conditions (see Note 3)
SN54AHC16240 SN74AHC16240
UNIT
MIN
2
MAX
MIN
2
MAX
V
V
Supply voltage
5.5
5.5
V
CC
V
V
V
V
V
V
= 2 V
1.5
2.1
3.85
1.5
2.1
3.85
CC
CC
CC
CC
CC
CC
High-level input voltage
= 3 V
V
V
IH
= 5.5 V
= 2 V
0.5
0.9
0.5
0.9
V
IL
Low-level input voltage
= 3 V
= 5.5 V
1.65
5.5
1.65
5.5
V
V
Input voltage
0
0
0
0
V
V
A
I
Output voltage
V
V
CC
O
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
V
CC
= 2 V
–50
–4
–8
50
4
–50
–4
–8
50
4
I
High-level output current
Low-level output current
= 3.3 ± 0.3 V
= 5 ± 0.5 V
= 2 V
OH
OL
mA
A
I
= 3.3 ± 0.3 V
= 5 ± 0.5 V
= 3.3 ± 0.3 V
= 5 ± 0.5 V
mA
8
8
100
20
125
100
20
85
∆t/∆v
Input transition rise or fall rate
Operating free-air temperature
ns/V
T
A
–55
–40
°C
NOTE 3: All unused inputs of the device must be held at V
or GND to ensure proper device operation. Refer to the TI application report,
CC
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
T
A
= 25°C
TYP
2
SN54AHC16240 SN74AHC16240
PARAMETER
TEST CONDITIONS
V
UNIT
CC
MIN
1.9
MAX
MIN
1.9
MAX
MIN
1.9
MAX
2 V
3 V
I
= –50
A
2.9
3
2.9
2.9
OH
V
V
4.5 V
3 V
4.4
4.5
4.4
4.4
V
OH
OL
I
I
= –4 mA
= –8 mA
2.58
3.94
2.48
3.8
2.48
3.8
OH
4.5 V
2 V
OH
0.1
0.1
0.1
0.1
0.1
0.5
0.5
±1*
0.1
0.1
I
= 50
A
3 V
OL
4.5 V
3 V
0.1
0.1
V
I
I
= 4 mA
= 8 mA
0.36
0.36
±0.1
0.44
0.44
±1
OL
4.5 V
0 V to 5.5 V
OL
I
I
V = V
or GND
A
A
I
CC
= V
V
or GND,
O
I
CC
V (OE) = V or V
IH
5.5 V
±0.25
±2.5
±2.5
I
OZ
CC
IL
I
V = V
or GND,
or GND
I = 0
O
5.5 V
5 V
4
40
40
10
A
pF
pF
I
CC
CC
C
C
V = V
2.5
3.5
10
i
I
V
= V or GND
CC
5 V
o
O
* On products compliant to MIL-PRF-38535, this parameter is not production tested at V
= 0 V.
CC
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN54AHC16240, SN74AHC16240
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS326G – MARCH 1996 – REVISED JANUARY 2000
switching characteristics over recommended operating free-air temperature range,
= 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1)
V
CC
T
A
= 25°C
TYP
SN54AHC16240 SN74AHC16240
UNIT
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE
PARAMETER
MIN
MAX
8.4*
8.4*
MIN
1*
1*
1*
1*
1*
1*
1
MAX
MIN
MAX
t
t
t
t
t
t
t
t
t
t
t
t
t
5.3*
10*
1
10
PLH
PHL
PZH
PZL
PHZ
PLZ
PLH
PHL
PZH
PZL
PHZ
PLZ
sk(o)
A
Y
Y
Y
Y
Y
Y
C
C
C
C
C
= 15 pF
= 15 pF
= 15 pF
= 50 pF
= 50 pF
ns
ns
ns
ns
ns
L
L
L
L
L
5.3*
10*
1
10
6.6* 10.6*
6.6* 10.6*
7.8* 11.5*
7.8* 11.5*
7.8 11.9*
12.5*
12.5*
12.5*
12.5*
13.5
13.5
16
1
12.5
12.5
12.5
12.5
13.5
13.5
16
OE
OE
A
1
1
1
1
7.8
9.1
11.9
14.1
14.1
14
1
1
1
1
OE
OE
9.1
1
16
1
16
10.3
10.3
1
16
1
16
C
C
= 50 pF
= 50 pF
ns
ns
L
L
14
1
16
1
16
**
1.5
1.5
* On products compliant to MIL-PRF-38535, this parameter is not production tested.
** On products compliant to MIL-PRF-38535, this parameter does not apply.
switching characteristics over recommended operating free-air temperature range,
= 5 V ± 0.5 V (unless otherwise noted) (see Figure 1)
V
CC
T
A
= 25°C
TYP
3.6*
3.6*
4.7*
4.7*
5.2*
5.2*
5.1
SN54AHC16240 SN74AHC16240
FROM
(INPUT)
TO
(OUTPUT)
LOAD
CAPACITANCE
PARAMETER
UNIT
ns
MIN
MAX
6*
MIN
1*
1*
1*
1*
1*
1*
1
MAX
7*
MIN
1
MAX
6.5
t
t
t
t
t
t
t
t
t
t
t
t
t
PLH
PHL
PZH
PZL
PHZ
PLZ
PLH
PHL
PZH
PZL
PHZ
PLZ
sk(o)
A
Y
Y
Y
Y
Y
Y
C
C
C
C
C
= 15 pF
= 15 pF
= 15 pF
= 50 pF
= 50 pF
L
L
L
L
L
6*
7*
1
6.5
7.3*
7.3*
7.2*
7.2*
8
8.5*
8.5*
8.5*
8.5*
9
1
8.5
ns
OE
OE
A
1
8.5
1
8.5
ns
1
8.5
1
8.5
ns
5.1
8
1
9
1
8.5
6.2
9.3
9.3
9.2
9.2
1
10.5
10.5
10.5
10.5
1
10.5
10.5
10.5
10.5
1
ns
OE
OE
6.2
1
1
6.7
1
1
C
C
= 50 pF
= 50 pF
ns
ns
L
L
6.7
1
1
**
1
* On products compliant to MIL-PRF-38535, this parameter is not production tested.
** On products compliant to MIL-PRF-38535, this parameter does not apply.
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN54AHC16240, SN74AHC16240
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS326G – MARCH 1996 – REVISED JANUARY 2000
noise characteristics, V
= 5 V, C = 50 pF, T = 25°C (see Note 4)
CC
L
A
SN74AHC16240
PARAMETER
UNIT
MIN
TYP
0.6
MAX
V
V
V
V
V
Quiet output, maximum dynamic V
V
V
V
V
V
OL(P)
OL(V)
OH(V)
IH(D)
IL(D)
OL
Quiet output, minimum dynamic V
Quiet output, minimum dynamic V
High-level dynamic input voltage
Low-level dynamic input voltage
–0.6
4.6
OL
OH
3.5
1.5
NOTE 4: Characteristics are for surface-mount packages only.
operating characteristics, V
= 5 V, T = 25°C
A
CC
PARAMETER
TEST CONDITIONS
No load, f = 1 MHz
TYP
UNIT
C
Power dissipation capacitance
10
pF
pd
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
SN54AHC16240, SN74AHC16240
16-BIT BUFFERS/DRIVERS
WITH 3-STATE OUTPUTS
SCLS326G – MARCH 1996 – REVISED JANUARY 2000
PARAMETER MEASUREMENT INFORMATION
V
CC
Open
GND
S1
R
= 1 kΩ
L
TEST
S1
From Output
Under Test
Test
Point
From Output
Under Test
t
t
/t
Open
PLH PHL
/t
C
C
L
t
V
CC
L
PLZ PZL
/t
(see Note A)
(see Note A)
GND
PHZ PZH
Open Drain
V
CC
LOAD CIRCUIT FOR
LOAD CIRCUIT FOR
TOTEM-POLE OUTPUTS
3-STATE AND OPEN-DRAIN OUTPUTS
V
CC
50% V
CC
Timing Input
0 V
t
w
t
h
t
su
V
CC
V
CC
50% V
50% V
CC
Input
CC
50% V
50% V
CC
Data Input
CC
0 V
0 V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
V
V
CC
CC
Output
Control
50% V
50% V
50% V
50% V
t
Input
CC
CC
CC
CC
0 V
0 V
t
PZL
t
t
t
PLZ
PLH
PHL
Output
Waveform 1
V
OH
≈V
CC
In-Phase
Output
50% V
50% V
CC
50% V
CC
CC
V
S1 at V
(see Note B)
V
OL
+ 0.3 V
CC
V
OL
OL
t
t
t
PHL
PLH
PZH
PHZ
Output
Waveform 2
S1 at GND
V
V
OH
OH
Out-of-Phase
Output
V
OH
– 0.3 V
50% V
50% V
50% V
CC
CC
CC
V
≈0 V
(see Note B)
OL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. includes probe and jig capacitance.
C
L
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, Z = 50 Ω, t ≤ 3 ns, t ≤ 3 ns.
O
r
f
D. The outputs are measured one at a time with one input transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
11-Nov-2009
PACKAGING INFORMATION
Orderable Device
74AHC16240DGGRE4
74AHC16240DGGRG4
74AHC16240DGVRE4
74AHC16240DGVRG4
SN74AHC16240DGGR
SN74AHC16240DGVR
SN74AHC16240DL
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
TSSOP
DGG
48
48
48
48
48
48
48
48
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TSSOP
TVSOP
TVSOP
TSSOP
TVSOP
SSOP
DGG
DGV
DGV
DGG
DGV
DL
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SN74AHC16240DLG4
SSOP
DL
25 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Aug-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
SN74AHC16240DGGR TSSOP
SN74AHC16240DGVR TVSOP
DGG
DGV
48
48
2000
2000
330.0
330.0
24.4
16.4
8.6
7.1
15.8
10.2
1.8
1.6
12.0
12.0
24.0
16.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Aug-2009
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
SN74AHC16240DGGR
SN74AHC16240DGVR
TSSOP
TVSOP
DGG
DGV
48
48
2000
2000
346.0
346.0
346.0
346.0
41.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
M
0,08
0,50
48
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
0,25
1
24
0°–8°
A
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
48
56
64
DIM
A MAX
12,60
12,40
14,10
13,90
17,10
16,90
A MIN
4040078/F 12/97
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MSSO001C – JANUARY 1995 – REVISED DECEMBER 2001
DL (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0.025 (0,635)
48
0.0135 (0,343)
0.008 (0,203)
0.005 (0,13)
M
25
0.010 (0,25)
0.005 (0,13)
0.299 (7,59)
0.291 (7,39)
0.420 (10,67)
0.395 (10,03)
Gage Plane
0.010 (0,25)
0°–ā8°
1
24
0.040 (1,02)
0.020 (0,51)
A
Seating Plane
0.004 (0,10)
0.008 (0,20) MIN
PINS **
0.110 (2,79) MAX
28
48
0.630
56
DIM
0.380
(9,65)
0.730
A MAX
A MIN
(16,00) (18,54)
0.370
(9,40)
0.620
0.720
(15,75) (18,29)
4040048/E 12/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MO-118
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,23
0,13
M
0,07
0,40
24
13
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–ā8°
0,75
1
12
0,50
A
Seating Plane
0,08
0,15
0,05
1,20 MAX
PINS **
14
16
20
24
38
48
56
DIM
A MAX
A MIN
3,70
3,50
3,70
3,50
5,10
4,90
5,10
4,90
7,90
7,70
9,80
9,60
11,40
11,20
4073251/E 08/00
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
D. Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Logic
Power Mgmt
Microcontrollers
RFID
Telephony
Video & Imaging
Wireless
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
相关型号:
SN74AHC16240DLR
AHC/VHC/H/U/V SERIES, QUAD 4-BIT DRIVER, INVERTED OUTPUT, PDSO48, GREEN, PLASTIC, SSOP-48
TI
SN74AHC16240DLRG4
AHC/VHC/H/U/V SERIES, QUAD 4-BIT DRIVER, INVERTED OUTPUT, PDSO48, GREEN, PLASTIC, SSOP-48
TI
©2020 ICPDF网 联系我们和版权申明