SN75LBC776DB [TI]
DUAL LINE TRANSCEIVER, PDSO20, PLASTIC, MO-150, SO-20;型号: | SN75LBC776DB |
厂家: | TEXAS INSTRUMENTS |
描述: | DUAL LINE TRANSCEIVER, PDSO20, PLASTIC, MO-150, SO-20 驱动 信息通信管理 光电二极管 接口集成电路 驱动器 |
文件: | 总15页 (文件大小:209K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
DB or DW PACKAGE
(TOP VIEW)
Single-Chip Interface Solution for the
9-terminal GeoPort Host (DTE)
Designed to Operate up to 4 Mbit/s Full
Duplex
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
DA1
GND
V
V
EE
CC
Single 5-V Supply Operation
C–
C+
DY1
RY3
RB3
RA2
RY2
RB1
RA1
RY1
6-kV ESD Protection on All Terminals
SHDN
DZ2
DY2
GND
DEN
DA2
Backward compatible With AppleTalk and
LocalTalk
Combines Multiple Components into a
Single-chip Solution
Complements the SN75LBC777 9-Terminal
GeoPort Peripheral (DCE) Interface Device
LinBiCMOS Process Technology
description
The SN75LBC776 is a low-power LinBiCMOS device that incorporates the drivers and receivers for a 9-pin
GeoPort host interface. GeoPort combines hybrid EIA/TIA-422-B and EIA/TIA-423-B drivers and receivers to
transmit data up to four megabits per second (Mbit/s) full duplex. GeoPort is a serial communications standard
that is intended to replace the RS-232, Appletalk, and LocalTalk printer ports all in one connector in addition
to providing real-time data transfer capability. It provides point-to-point connections between
GeoPort-compatible devices with data transmission rates up to 4 Mbit/s full duplex and a hot-plug feature.
Applications include connection to telephony, integrated services digital network (ISDN), digital sound and
imaging, fax-data modems, and other serial and parallel connections. The GeoPort is backwardly compatible
to both LocalTalk and AppleTalk.
WhiletheSN75LBC776ispowered-off(V =0)theoutputsareinahigh-impedancestate. Whentheshutdown
CC
(SHDN) terminal is high, the charge pump is powered down and the outputs are in a high-impedance state. The
driver enable (DEN) terminal sends the outputs of the differential driver into a high-impedance state with a high
input signal. All drivers and receivers have fail-safe mechanisms to ensure a high output state when the inputs
are left open.
A switched-capacitor voltage converter generates the negative voltage required from a single 5-V supply using
four 0.1-µF capacitors, two capacitors between the C+ and C- terminals and two capacitors between V and
EE
ground.
The SN75LBC776 is characterized for operation over the 0°C to 70°C temperature range.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
GeoPort, LocalTalk, and AppleTalk are trademarks of Apple Computer, Incorporated.
LinBiCMOS is a trademark of Texas Instruments Incorporated.
Copyright 2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
†
DRIVER FUNCTION TABLE
OUTPUT
INPUT
DA1
INPUT
DA2
ENABLE
SHDN
ENABLE
DEN
OUTPUT
DY1
DY2
DZ2
X
H
X
L
X
L
H
X
X
L
X
X
H
L
L
X
L
X
X
X
H
L
L
L
X
L
L
L
H
L
OPEN
OPEN
L
L
X
H
Z
Z
Z
X
X
X
X
X
X
H
X
Z
X
Z
Z
H
Z
OPEN
OPEN
Z
†
H = high level L = low level
X = irrelevant
? = indeterminate Z = high impedance (off)
†
RECEIVER FUNCTION TABLE
INPUT
RA1 RB1
INPUT
RA2 & RB3
ENABLE
SHDN
OUTPUT
RY1
OUTPUT
RY2
OUTPUT
RY3
H
L
L
H
L
L
H
L
H
L
L
H
L
H
OPEN
OPEN
L
H
?
H
?
H
‡
‡
SHORT
SHORT
L
H
?
X
X
X
X
X
Z
Z
Z
Z
Z
X
OPEN
Z
†
‡
H = high level L = low level
–0.2 V < V < 0.2 V
X = irrelevant
? = indeterminate Z = high impedance (off)
ID
function logic diagram (positive logic)
7
DY2
10
DA2
6
DZ2
9
DEN
12
RA1
11
RY1
13
RB1
1
18
DY1
DA1
15
RA2
14
RY2
17
RY3
16
RB3
5
SHDN
19
V
Charge
Pump
CC
2
V
EE
(–5 V)
20
GND
2
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Positive supply voltage range, V
Negative supply voltage range, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –7 to 0.5 V
Receiver input voltage range (RA, RB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –15 V to 15 V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 to 7 V
CC
EE
Receiver differential input voltage range, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –12 to 12 V
ID
Receiver output voltage range (RY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V
Driver output voltage range (Power Off) (DY1, DY2, DZ2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –15 V to 15 V
Driver output voltage range (Power On) (DY1, DY2, DZ2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –11 V to 11 V
Driver input voltage range (DA, SHND, DEN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to V
0.4 V
CC+
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Electrostatic discharge (see Note 2): (Bus terminals), Class 3, A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 kV
(Bus terminals), Class 3, B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 V
(All terminals), Class 3, A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 kV
(All terminals), Class 3, B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 V
Operating free-air temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
A
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
†
NOTES: 1. All voltage values are with respect to network ground terminal unless otherwise noted.
2. This parameter is measured in accordance with MIL-STD-883C, Method 3015.7.
DISSIPATION RATING TABLE
T
≤ 25°C
OPERATING FACTOR
T = 70°C
A
POWER RATING
A
PACKAGE
POWER RATING
ABOVE T = 25°C
A
DB
1035 mW
8.3 mW/°C
9.0 mW/°C
660 mW
DW
1125 mW
720 mW
3
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
recommended operating conditions
MIN NOM
MAX
5.25
5.25
0.8
7
UNIT
V
Supply voltage, V
CC
4.75
2
5
High-level input voltage, V
IH
DA, SHDN, DEN
DA, SHDN, DEN
V
Low-level input voltage, V
V
IL
Receiver common-mode input voltage, V
IC
–7
–12
0.2
V
Receiver differential input voltage, V
Voltage-converter filter capacitance
12
V
ID
µF
Ω
Voltage-converter filter-capacitor equivalent series resistance (ESR)
Operating free-air temperature, T
0.2
70
0
°C
A
driver electrical characteristics over operating free-air temperature range (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
3.6
2
TYP
4.53
MAX
UNIT
R
R
R
R
= 12 kΩ
= 120 Ω
= 12 kΩ
= 120 Ω
V
V
V
V
L
L
L
L
V
V
High-level output voltage
OH
3.63
Single ended,
See Figure 1
–4.53
–2.7
–3.6
–1.8
Low-level output voltage
OL
Magnitude of differential output voltage
|V
|
4
V
OD
|(V
– V
|
(DZ)
(DY)
R
= 120 Ω,
See Figure 2
L
∆|V
|
Change in differential voltage magnitude
Common-mode output voltage
250
3
mV
V
OD
V
OC
–1
Magnitude of change, common-mode steady
state output voltage
|∆V
|
|
200
mV
mV
OC(SS)
OC(PP)
See Figure 3
Magnitude of change, common-mode
peak-to-peak output voltage
|∆V
700
7
SHDN = DEN = 0 V,
SHDN = DEN = 5 V,
No load
No load
15
100
mA
µA
I
Supply current
CC
I
I
High-impedance output current
V
= –10 V to 10 V,
= –5 V to 5 V
V = 0 or 5 V
CC
±100
µA
OZ
O
O
Short-circuit output current (see Note 3)
V
±170 ±450
mA
OS
NOTE 3: Not more than one output should be shorted at one time.
4
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
driver switching characteristics over operating free-air temperature range (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
42
41
25
25
28
37
25
23
40
42
25
29
25
35
28
34
37
34
27
26
MAX
75
UNIT
ns
ns
µs
µs
ns
ns
ns
ns
ns
ns
µs
ns
µs
ns
ns
ns
ns
ns
ns
ns
ns
t
t
t
t
t
t
t
t
t
t
Propagation delay time, high-to-low level output
Propagation delay time, low-to-high level output
Driver output enable time to low-level output
Driver output enable time to high-level output
Driver output disable time from low-level output
Driver output disable time from high-level output
Rise time
PHL
PLH
PZL
PZH
PLZ
PHZ
r
75
100
100
100
100
75
Single ended,
See Figure 4
SHDN
10
10
Fall time
75
f
Propagation delay time, high-to-low level output
Propagation delay time, low-to-high level output
75
PHL
PLH
75
SHDN
DEN
100
150
100
150
100
100
100
100
75
t
t
t
t
Driver output enable time to low-level output
Driver output enable time to high-level output
Driver output disable time from low-level output
Driver output disable time from high-level output
PZL
PZH
PLZ
PHZ
SHDN
DEN
Differential,
See Figure 5
SHDN
DEN
SHDN
DEN
t
t
t
Rise time
Fall time
10
10
r
75
f
Pulse skew, |t
– t
|
22
SK(p)
PLH PHL
receiver electrical characteristics over operating free-air temperature range (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
MIN
–200
2
TYP
MAX
UNIT
V
IT+
V
IT–
V
hys
V
OH
V
OL
Positive-going input threshold voltage
Negative-going input threshold voltage
200
mV
See Figure 6
Differential input voltage hysteresis (V
High-level output voltage (see Note 4)
Low-level output voltage
– V
)
IT–
50
4.9
0.2
–45
47
mV
V
IT+
V
V
V
V
V
= 0,
= 0,
= 0
I
I
= –2 mA, See Figure 6
IC
IC
O
OH
= 2 mA,
See Figure 6
0.8
V
OL
–85
I
Short-circuit output current
Input resistance
mA
OS
= V
+85
O
CC
= 0 or 5.25 V,
V = –12 V to 12 V
CC
R
6
30
kΩ
I
I
NOTE 4: When the inputs are left unconnected, receivers one and two interpret these as high-level inputs and receiver three interprets these
as low-level inputs so that all outputs are at a high level.
5
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
receiver switching characteristics over operating free-air temperature range (unless otherwise
noted)
PARAMETER
Propagation delay time, high-to-low-level output
Propagation delay time, low-to-high level output
Rise time
TEST CONDITIONS
MIN
TYP
31
MAX
75
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
µs
ns
ns
t
t
t
t
t
t
t
t
t
t
t
t
t
PHL
PLH
r
30
75
R
= 2 kΩ,
See Figure 6
C
= 15 pF,
L
L
15
30
Fall time
15
30
f
Pulse skew |t
–t
|
20
SK(P)
PZL
PZH
PLZ
PHZ
PZL
PZH
PLZ
PHZ
PLH PHL
Receiver output enable time to low level output
Receiver output enable time to high level output
Receiver output disable time from low level output
Receiver output disable time from high level output
Receiver output enable time to low level output
Receiver output enable time to high level output
Receiver output disable time from low level output
Receiver output disable time from high level output
35
32
100
100
100
100
25
Differential,
See Figure 7
C
C
=50 pF,
=50 pF,
L
L
21
21
12
12
25
Single ended,
See Figure 7
25
100
400
125
6
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
PARAMETER MEASUREMENT INFORMATION
C
C
L
L
I
O
R
R
L
L
C
R
L
L
DY2
DZ2
I
I
O
I
DY1
I
I
V
V
O
DA1
DA2
I
O
V
V
V
I
I
O
SHDN
O
SHDN
or
DEN
NOTE A: C = 50 pF
L
TEST CIRCUIT
Figure 1. Single-Ended Driver DC Parameter Test
DY2
DZ2
60 Ω
60 Ω
I
I
O
I
V
OD
DA2
V
I
50 pF
SHDN
or
DEN
TEST CIRCUIT
Figure 2. Differential Driver DC Parameter Test
DY2
DZ2
60 Ω
60 Ω
V
OD
DA2
V
I
V
OC
15 pF
SHDN
or
DEN
TEST CIRCUIT (see Note A)
3 V
0 V
V
I
1.5 v
1.5 v
V
OC
0 V
V
OC(SS)
V
OC(PP)
VOLTAGE WAVEFORM
NOTE A: Measured 3dB bandwidth = 300 MHz
Figure 3. Differential-Driver Common-Mode Output Voltage Tests
7
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
PARAMETER MEASUREMENT INFORMATION
C
C
L
L
I
O
R
R
L
L
C
= 50 pF
L
DY2
DZ2
I
I
V
V
O
DY1
DA1
DA2
R
= 120 Ω
L
I
O
V
O
V
I
SHDN
O
SHDN
or
DEN
TEST CIRCUIT
(see Note A)
3 V
0 V
SHDN
or
DEN
1.5 V
1.5 V
1.5 V
1.5 V
3 V
0 V
1.5 V
1.5 V
DA
t
PLH
t
t
t
PZL
t
PHL
PLZ
PHZ
V
OH
90%
90%
90%
DY1, DZ2
10%
90%
0 V
50%
10%
50%
10%
10%
V
OL
t
PZH
t
PLZ
t
f
t
r
t
t
PHL
PHZ
t
PLH
t
PZH
90%
V
OH
DY2
90%
90%
10%
90%
50%
0 V
50%
10%
10%
10%
V
OL
t
t
f
t
PZL
r
VOLTAGE WAVEFORM
(see Note B)
NOTES: A.
C = 50 pF, R = 120 Ω
L L
B. The input waveform t , t ≤ 10 ns.
r f
Figure 4. Single-Ended Driver Propagation and Transition Times
8
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
PARAMETER MEASUREMENT INFORMATION
DY2
DZ2
R
R
60 Ω
60 Ω
L =
L =
V
OD
DA2
V
I
50 pF
SHDN
or
DEN
TEST CIRCUIT
3 V
0 V
SHDN
or
DEN
1.5 V
1.5 V
1.5 V
1.5 V
3 V
0 V
1.5 V
1.5 V
DA
t
PHL
t
t
t
t
PLH
PHZ
90%
PZH
90%
PLZ
V
OD(H)
90%
V
OD
10%
50%
10%
50%
10%
0 V
90%
10%
V
OD(L)
t
PZL
t
f
t
r
VOLTAGE WAVEFORM
(see Note A)
Figure 5. Differential Driver Propagation and Transition Times
V
CC
2 kΩ
2.5 V
V
0 V
0 V
I
I
I
–2.5 V
RA
RB
I
O
+
_
Input
t
t
RY
PLH
PHL
Output
V
OH
V
I
90%
90%
V
O
V
O
1.5 V
15 pF
10%
10%
V
OL
SHDN
t
t
f
r
TEST CIRCUIT
VOLTAGE WAVEFORM
(see Note A)
Figure 6. Receiver Propagation and Transition Times
NOTE A: The input waveform t , t ≤ 10 ns.
r f
9
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
PARAMETER MEASUREMENT INFORMATION
V
CC
RA
RB
R
= 500 Ω
+
_
L
–2.5 V or 2.5 V
RY
S1
C
= 50 pF
L
SHDN
TEST CIRCUIT
3 V
0 V
SHDN
1.5 V
1.5 V
90%
t
t
PZL
PLZ
V
CC
S1 at V
CC
10%
90%
V
OL
OH
V
O
t
t
PZH
PHZ
V
S1 at GND
10%
0 V
VOLTAGE WAVEFORM
(see Note A)
NOTE A: The input waveform t , t ≤ 10 ns.
r f
Figure 7. Receiver Enable and Disable Test Circuit and Waveforms
10
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
APPLICATION INFORMATION
RxD
11
13
12
RxD–
GeoPort
Host
SN75LBC776
9-Terminal
DTE
GeoPort
Peripheral
Device
9-Pin
RxD+
TxD+
7
6
10
5
TxD
SHDN
DTR
TxD–
DCE
GeoPort
Controller
and USART
GND
1
RESET/ATT
SCLK
18
15
RESET/ATT
SCLK
14
17
9
RTXC
CTS
Power
TxHS/WAKE-UP
16
RTS
TxHS/WAKE-UP
V
CC
RxD–
13
12
Standard
Host
SN75LBC776
9-Terminal
DTE
19
RxD+
16 TxHS/WAKE-UP
4
3
+
+
+
7
6
TxD+
0.1 µF
0.1 µF
6
7
8
V
CC
TxD–
3
4
1
9
2
5
–5 V
(see Note A)
V
EE
GND
2
Power
0.1 µF
0.1 µF
18
15
RESET/ATT
SCLK
+
8
20
NOTE A: The AVX 0603YC104MATXA or equivalent is one of the possible capacitors that can be used as the charge pump capacitor.
Figure 8. GeoPort 9-Terminal DTE Connection Application
11
www.ti.com
SN75LBC776
SINGLE-CHIP GeoPort TRANSCEIVER
SLLS221B – NOVEMBER 1995 – REVISED MARCH 2002
APPLICATION INFORMATION
generator characteristics
EIA/TIA-232/V.28
EIA/TIA-423/V.10
562
MIN
PARAMETER
TEST CONDITIONS
UNIT
MIN
MAX
25
MIN
4
MAX
MAX
Open circuit
6
13.2
V
V
V
|V
|
Output voltage magnitude
3 kΩ ≤ R ≤ 7 kΩ
5
NA
NA
15
NA
3.6
3.7
NA
O
L
R
= 450 Ω
L
V
Output voltage ringing
10%
150
5%
60
O(RING)
I
Short-circuit output current
V
V
V
= 0
100
mA
Ω
OS
O(OFF)
O
= 0, |V | < 2 V
300
NA
NA
300
NA
4
CC
CC
O
I
Power-off output current
Output voltage slew rate
= 0, |V | < 6 V
±100
µA
O
SR
30
NA
NA
NA
30
V/µs
µs
±3.3 V to ±3.3 V
±3 V to ±3 V
10% to 90%
NA
NA
0.22
NA
NA
2.1
†
t
t
Transition time
0.04
ui
ui
†
0.3
†
ui is the unit interval and is the inverse of the signaling rate (bit transmit time).
receiver characteristics
EIA/TIA-232/V.28
EIA/TIA-423/V.10
562
PARAMETER
TEST CONDITIONS
UNIT
V
MIN
MAX
25
MIN
MAX
MIN
MAX
25
|V |
I
Input voltage magnitude
Input voltage threshold
10
|V | < 15 V
–3
NA
3
3
NA
–0.2
NA
4
–3
NA
3
3
I
V
IT
V
|V | < 10 V
0.2
I
3 V < |V | < 15 V
7
7
kΩ
kΩ
I
R
Input resistance
I
|V | < 10 V
NA
NA
I
12
www.ti.com
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
MECHANICAL INFORMATION
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
M
0,15
15
0,25
0,09
5,60
5,00
8,20
7,40
Gage Plane
1
14
0,25
A
0°–8°
0,95
0,55
Seating Plane
0,10
2,00 MAX
0,05 MIN
PINS **
14
16
20
24
28
30
38
DIM
6,50
5,90
6,50
5,90
7,50
8,50
7,90
10,50
9,90
10,50 12,90
A MAX
A MIN
6,90
9,90
12,30
4040065 /E 12/01
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
13
www.ti.com
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
MECHANICAL INFORMATION
DW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
16 PIN SHOWN
PINS **
0.050 (1,27)
16
20
24
28
DIM
0.020 (0,51)
0.014 (0,35)
0.010 (0,25)
M
0.410
0.510
0.610
0.710
A MAX
(10,41) (12,95) (15,49) (18,03)
16
9
0.400
0.500
0.600
0.700
A MIN
(10,16) (12,70) (15,24) (17,78)
0.419 (10,65)
0.400 (10,15)
0.010 (0,25) NOM
0.299 (7,59)
0.293 (7,45)
Gage Plane
0.010 (0,25)
1
8
0°–8°
0.050 (1,27)
0.016 (0,40)
A
Seating Plane
0.004 (0,10)
0.012 (0,30)
0.004 (0,10)
0.104 (2,65) MAX
4040000/B 10/94
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MS-013
14
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, maskworkright, orotherTIintellectualpropertyrightrelatingtoanycombination, machine, orprocess
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2002, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明