TCA6408PWR [TI]
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS; 低压8位I2C和SMBus I / O扩展器,带有中断输出,复位和配置寄存器型号: | TCA6408PWR |
厂家: | TEXAS INSTRUMENTS |
描述: | LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS |
文件: | 总30页 (文件大小:842K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
FEATURES
•
Operating Power-Supply Voltage Range of
1.65 V to 5.5 V
•
•
•
•
•
•
•
•
5-V Tolerant I/O Ports
Active-Low Reset Input (RESET)
Open-Drain Active-Low Interrupt Output (INT)
400-kHz Fast I2C Bus
•
Allows Bidirectional Voltage-Level Translation
and GPIO Expansion Between
–
–
–
–
1.8-V SCL/SDA and 1.8-V, 2.5-V,
3.3-V, or 5-V P Port
Input/Output Configuration Register
Polarity Inversion Register
2.5-V SCL/SDA and 1.8-V, 2.5-V,
3.3-V, or 5-V P Port
Internal Power-On Reset
Power-Up With All Channels Configured as
Inputs
3.3-V SCL/SDA and 1.8-V, 2.5-V,
3.3-V, or 5-V P Port
•
•
•
No Glitch On Power-Up
5-V SCL/SDA and 1.8-V, 2.5-V,
3.3-V, or 5-V P Port
Noise Filter on SCL/SDA Inputs
I2C to Parallel Port Expander
Latched Outputs With High-Current Drive
Maximum Capability for Directly Driving LEDs
•
•
•
Low Standby Current Consumption of 1 µA
•
•
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
Schmitt-Trigger Action Allows Slow Input
Transition and Better Switching Noise
Immunity at the SCL and SDA Inputs
ESD Protection Exceeds JESD 22
–
–
–
2000-V Human-Body Model (A114-A)
200-V Machine Model (A115-A)
–
–
–
–
Vhys = 0.18 V Typ at 1.8 V
Vhys = 0.25 V Typ at 2.5 V
Vhys = 0.33 V Typ at 3.3 V
Vhys = 0.5 V Typ at 5 V
1000-V Charged-Device Model (C101)
RGT PACKAGE
(TOP VIEW)
PW PACKAGE
(TOP VIEW)
ZXY PACKAGE
(TOP VIEW)
VCCI
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
VCCP
SDA
SCL
ADDR
1
5
2
3
4
16 15 14 13
RESET
SCL
INT
P7
RESET
P0
1
2
3
4
12
11
10
9
A
B
C
D
P0
P1
P2
INT
P7
P1
P6
P6
P2
5
6
7
8
P3
P5
P4
GND
DESCRIPTION/ORDERING INFORMATION
This 8-bit I/O expander for the two-line bidirectional bus (I2C) is designed to provide general-purpose remote I/O
expansion for most microcontroller families via the I2C interface [serial clock (SCL) and serial data (SDA)].
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
Copyright © 2007, Texas Instruments Incorporated
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
ORDERING INFORMATION
TA
PACKAGE(1)
ORDERABLE PART NUMBER
TCA6408RGTR
TOP-SIDE MARKING
QFN – RGT
Reel of 3000
Reel of 2500
Tube of 70
ZWP
BGA – ZXY (Pb-free)
TCA6408ZXYR
PH408
–40°C to 85°C
TCA6408PW
TSSOP – PW
PH408
Reel of 2000
TCA6408PWR
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
The major benefit of this device is its wide VCC range. It can operate from 1.65-V to 5.5-V on the P port side and
on the SDA/SCL side. This allows the TCA6408 to interface with next-generation microprocessors and
microcontrollers on the SDA/SCL side, where supply levels are dropping down to conserve power. In contrast to
the dropping power supplies of microprocessors and microcontrollers, some PCB components such as LEDs
remain at a 5-V power supply.
The bidirectional voltage level translation in the TCA6408 is provided through VCCI. VCCI should be connected to
the VCC of the external SCL/SDA lines. This indicates the VCC level of the I2C bus to the TCA6408. The voltage
level on the P port of the TCA6408 is determined by VCCP
.
The TCA6408 consists of one 8-bit configuration (input or output selection), input, output, and polarity inversion
(active high) register. At power on, the I/Os are configured as inputs. However, the system master can enable
the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is
kept in the corresponding input or output register. The polarity of the input port register can be inverted with the
polarity inversion register. All registers can be read by the system master.
The system master can reset the TCA6408 in the event of a timeout or other improper operation by asserting a
low in the RESET input. The power-on reset puts the registers in their default state and initializes the I2C/SMBus
state machine. The RESET pin causes the same reset/initialization to occur without depowering the part.
The TCA6408 open-drain interrupt (INT) output is activated when any input state differs from its corresponding
input port register state and is used to indicate to the system master that an input state has changed.
INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the
remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via
the I2C bus. Thus, the TCA6408 can remain a simple slave device.
The device P port outputs have high-current sink capabilities for directly driving LEDs while consuming low
device current.
One hardware pin (ADDR) can be used to program and vary the fixed I2C address and allow up to two devices
to share the same I2C bus or SMBus.
2
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
ZXY Terminal Assignments
1
P3
2
3
4
5
A
B
C
D
P2
P1
P0
INT
P7
RESET
N.C.(1)
N.C.(1)
SCL
ADDR
VCCI
GND
P4
N.C.(1)
N.C.(1)
P6
VCCP
SDA
P5
(1) N.C. – No internal connection
TERMINAL FUNCTIONS
PIN NUMBER
NAME
DESCRIPTION
TSSOP
(PW)
QFN
(RGT)
BGA
(ZXY)
Supply voltage of I2C bus. Connect directly to the VCC of the external I2C master.
Provides voltage level translation.
1
2
3
15
16
1
B5
A5
A4
VCCI
ADDR
RESET
Address input. Connect directly to VCCP or ground.
Active-low reset input. Connect to VCCP through a pullup resistor, if no active
connection is used.
P port input/output (push-pull design structure). At power on, P0 is configured as
an input.
4
5
6
2
3
4
B3
A3
A2
P0
P1
P2
P port input/output (push-pull design structure). At power on, P1 is configured as
an input.
P port input/output (push-pull design structure). At power on, P2 is configured as
an input.
P port input/output (push-pull design structure). At power on, P3 is configured as
an input.
7
8
9
5
6
7
A1
B1
C1
P3
GND
P4
Ground
P port input/output (push-pull design structure). At power on, P4 is configured as
an input.
P port input/output (push-pull design structure). At power on, P5 is configured as
an input.
10
11
12
8
9
D1
D2
D3
P5
P6
P7
P port input/output (push-pull design structure). At power on, P6 is configured as
an input.
P port input/output (push-pull design structure). At power on, P7 is configured as
an input.
10
13
14
15
16
11
12
13
14
C3
D4
D5
C5
INT
SCL
SDA
VCCP
Interrupt output. Connect to VCCI through a pullup resistor.
Serial clock bus. Connect to VCCI through a pullup resistor.
Serial data bus. Connect to VCCI through a pullup resistor.
Supply voltage of TCA6408 for P port.
3
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
Voltage Translation
Table 1 shows how to set up VCC levels for the necessary voltage translation between the I2C bus and the
TCA6408.
Table 1. Voltage Translation
VCCI
VCCP
(P Port)
(V)
(SCL and SDA of I2C master)
(V)
1.8
1.8
1.8
1.8
2.5
2.5
2.5
2.5
3.3
3.3
3.3
3.3
5
1.8
2.5
3.3
5
1.8
2.5
3.3
5
1.8
2.5
3.3
5
1.8
2.5
3.3
5
5
5
5
4
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
LOGIC DIAGRAM (POSITIVE LOGIC)
Interrupt
Logic
13
INT
LP Filter
2
ADDR
14
15
SCL
SDA
Input
Filter
I2C Bus
Control
Shift
Register
P7–P0
8 Bits
I/O Port
1
VCCI
Write Pulse
Read Pulse
16
3
VCCP
Power-On
Reset
RESET
8
GND
A. All pin numbers shown are for the PW package.
B. All I/Os are set to inputs at reset.
5
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
Simplified Schematic of P0 to P7
Data From
Shift Register
Configuration
Output Port
Register Data
Register
VCCP
Data From
Shift Register
D
Q
Q1
FF
CK
Write Configuration
Pulse
D
Q
Q
Q
FF
CK
P0 to P7
Write Pulse
Q2
ESD Protection Diode
Output
Port
Register
Input
Port
Register
GND
Input Port
D
Q
Q
Register Data
FF
Read Pulse
CK
To INT
Data From
Shift Register
Polarity
D
Q
Q
Register Data
FF
CK
Write Polarity Pulse
Polarity
Inversion
Register
A. On power up or reset, all registers return to default values.
I/O Port
When an I/O is configured as an input, FETs Q1 and Q2 are off, which creates a high-impedance input. The
input voltage may be raised above VCC to a maximum of 5.5 V.
If the I/O is configured as an output, Q1 or Q2 is enabled depending on the state of the output port register. In
this case, there are low impedance paths between the I/O pin and either VCC or GND. The external voltage
applied to this I/O pin should not exceed the recommended levels for proper operation.
I2C Interface
The bidirectional I2C bus consists of the serial clock (SCL) and serial data (SDA) lines. Both lines must be
connected to a positive supply through a pullup resistor when connected to the output stages of a device. Data
transfer may be initiated only when the bus is not busy.
I2C communication with this device is initiated by a master sending a start condition, a high-to-low transition on
the SDA input/output, while the SCL input is high (see Figure 1). After the start condition, the device address
byte is sent, MSB first, including the data direction bit (R/W).
After receiving the valid address byte, this device responds with an acknowledge (ACK), a low on the SDA
input/output during the high of the ACK-related clock pulse. The address input (ADDR) of the slave device must
not be changed between the start and the stop conditions.
On the I2C bus, only one data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the high pulse of the clock period, as changes in the data line at this time are interpreted as control
commands (start or stop) (see Figure 2).
6
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
A stop condition, a low-to-high transition on the SDA input/output while the SCL input is high, is sent by the
master (see Figure 1).
Any number of data bytes can be transferred from the transmitter to receiver between the start and the stop
conditions. Each byte of eight bits is followed by one ACK bit. The transmitter must release the SDA line before
the receiver can send an ACK bit. The device that acknowledges must pull down the SDA line during the ACK
clock pulse, so that the SDA line is stable low during the high pulse of the ACK-related clock period (see
Figure 3). When a slave receiver is addressed, it must generate an ACK after each byte is received. Similarly,
the master must generate an ACK after each byte that it receives from the slave transmitter. Setup and hold
times must be met to ensure proper operation.
A master receiver signals an end of data to the slave transmitter by not generating an acknowledge (NACK)
after the last byte has been clocked out of the slave. This is done by the master receiver by holding the SDA line
high. In this event, the transmitter must release the data line to enable the master to generate a stop condition.
SDA
SCL
S
P
Stop Condition
Start Condition
Figure 1. Definition of Start and Stop Conditions
SDA
SCL
Data Line
Change
Figure 2. Bit Transfer
Data Output
by Transmitter
NACK
Data Output
by Receiver
ACK
SCL From
Master
1
2
8
9
S
Clock Pulse for
Acknowledgment
Start
Condition
Figure 3. Acknowledgment on the I2C Bus
7
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
Interface Definition
BIT
BYTE
7 (MSB)
6
H
5
L
4
L
3
L
2
L
1
0 (LSB)
R/W
I2C slave address
I/O data bus
L
ADDR
P1
P7
P6
P5
P4
P3
P2
P0
Device Address
The address of the TCA6408 is shown in Figure 4.
Slave Address
AD
0
1
0
0
0
0
DR
R/W
Fixed
Programmable
Figure 4. TCA6408 Address
Address Reference
ADDR
I2C BUS SLAVE ADDRESS
32 (decimal), 20 (hexadecimal)
33 (decimal), 21 (hexadecimal)
L
H
The last bit of the slave address defines the operation (read or write) to be performed. A high (1) selects a read
operation, while a low (0) selects a write operation.
Control Register and Command Byte
Following the successful acknowledgement of the address byte, the bus master sends a command byte, which
is stored in the control register in the TCA6408. Two bits of this data byte state the operation (read or write) and
the internal registers (input, output, polarity inversion or configuration) that will be affected. This register can be
written or read through the I2C bus. The command byte is sent only during a write transmission.
B7 B6
B5 B4 B3 B2 B1 B0
Figure 5. Control Register Bits
Command Byte
CONTROL REGISTER BITS
COMMAND
BYTE
POWER-UP
DEFAULT
REGISTER
PROTOCOL
B7
B6
B5
B4
B3
B2
B1
B0
(HEX)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
1
0
1
00
Input Port
Read byte
xxxx xxxx(1)
1111 1111
0000 0000
1111 1111
01
Output Port
Read/write byte
02
Polarity Inversion Read/write byte
Configuration Read/write byte
03
(1) Undefined
8
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
Register Descriptions
The input port register (register 0) reflects the incoming logic levels of the pins, regardless of whether the pin is
defined as an input or an output by the configuration register. They act only on read operation. Writes to this
register have no effect. The default value (X) is determined by the externally applied logic level. Before a read
operation, a write transmission is sent with the command byte to indicate to the I2C device that the input port
register will be accessed next.
Register 0 (Input Port Register)
BIT
I-7
X
I-6
X
I-5
X
I-4
X
I-3
X
I-2
X
I-1
X
I-0
X
DEFAULT
The output port register (register 1) shows the outgoing logic levels of the pins defined as outputs by the
Configuration register. Bit values in this register have no effect on pins defined as inputs. In turn, reads from this
register reflect the value that is in the flip-flop controlling the output selection, not the actual pin value.
Register 1 (Output Port Register)
BIT
O-7
1
O-6
1
O-5
1
O-4
1
O-3
1
O-2
1
O-1
1
O-0
1
DEFAULT
The polarity inversion register (register 2) allows polarity inversion of pins defined as inputs by the configuration
register. If a bit in this register is set (written with 1), the corresponding port pin's polarity is inverted. If a bit in
this register is cleared (written with a 0), the corresponding port pin's original polarity is retained.
Register 2 (Polarity Inversion Register)
BIT
N-7
0
N-6
0
N-5
0
N-4
0
N-3
0
N-2
0
N-1
0
N-0
0
DEFAULT
The configuration register (register 3) configures the direction of the I/O pins. If a bit in this register is set to 1,
the corresponding port pin is enabled as an input with a high-impedance output driver. If a bit in this register is
cleared to 0, the corresponding port pin is enabled as an output.
Register 3 (Configuration Register)
BIT
C-7
1
C-6
1
C-5
1
C-4
1
C-3
1
C-2
1
C-1
1
C-0
1
DEFAULT
Power-On Reset
When power (from 0 V) is applied to VCCP, an internal power-on reset holds the TCA6408 in a reset condition
until VCCP has reached VPOR. At that time, the reset condition is released, and the TCA6408 registers and
I2C/SMBus state machine initialize to their default states. After that, VCCP must be lowered to below 0.2 V and
back up to the operating voltage for a power-reset cycle.
Reset Input (RESET)
The RESET input can be asserted to intialize the system while keeping VCCP at its operating level. A reset can
be accomplished by holding the RESET pin low for a minimum of tW. The TCA6408 registers and I2C/SMBus
state machine are changed to their default state once RESET is low (0). When RESET is high (1), the I/O levels
at the P port can be changed externally or through the master. This input requires a pullup resistor to VCCP, if no
active connection is used.
9
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
Interrupt Output (INT)
An interrupt is generated by any rising or falling edge of the port inputs in the input mode. After time tiv, the
signal INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original
setting, data is read from the port that generated the interrupt or in a stop event. Resetting occurs in the read
mode at the acknowledge (ACK) or not acknowledge (NACK) bit after the rising edge of the SCL signal. In a
stop event, INT is cleared after the rising edge of SDA. Interrupts that occur during the ACK or NACK clock
pulse can be lost (or be very short) due to the resetting of the interrupt during this pulse. Each change of the
I/Os after resetting is detected and is transmitted as INT.
Reading from or writing to another device does not affect the interrupt circuit, and a pin configured as an output
cannot cause an interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur, if the
state of the pin does not match the contents of the input port register.
The INT output has an open-drain structure and requires a pullup resistor to VCCP or VCCI depending on the
application. If the INT signal is connected back to the processor that provides the SCL signal to the TCA6408,
then the INT pin has to be connected to VCCI. If not, the INT pin can be connected to VCCP
.
Bus Transactions
Data is exchanged between the master and TCA6408 through write and read commands.
Writes
Data is transmitted to the TCA6408 by sending the device address and setting the least-significant bit to a logic
0 (see Figure 4 for device address). The command byte is sent after the address and determines which register
receives the data that follows the command byte. There is no limitation on the number of data bytes sent in one
write transmission.
SCL
1
2
3
4
5
6
7
8
9
Slave Address
Command Byte
Data to Port
Data 1
AD
DR
SDA
S
0
1
0
0
0
0
0
A
0
0
0
0
0
0
0
1
A
A
P
Start Condition
R/W ACK From Slave
ACK From Slave
ACK From Slave
Write to Port
Data Out
Data 1 Valid
From Port
tpv
Figure 6. Write to Output Port Register
<br/>
SCL
1
2
3
4
5
6
7
8
0
9
Slave Address
Command Byte
Data to Register
Data
AD
DR
1
SDA
S
0
1
0
0
0
0
A
0
0
0
0
0
0
1/0
A
A
P
Start Condition
R/W ACK From Slave
ACK From Slave
ACK From Slave
Figure 7. Write to Configuration or Polarity Inversion Registers
10
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
Reads
The bus master first must send the TCA6408 address with the least-significant bit set to a logic 0 (see Figure 4
for device address). The command byte is sent after the address and determines which register is accessed.
After a restart, the device address is sent again but, this time, the least-significant bit is set to a logic 1. Data
from the register defined by the command byte then is sent by the TCA6408 (see Figure 8 and Figure 9).
Data is clocked into the register on the rising edge of the ACK clock pulse.
ACK From
Master
ACK From
Slave
ACK From
Slave
ACK From
Slave
Data from Register
Slave Address
Slave Address
AD
DR
AD
DR
Command Byte
S
0
1
0
0
0
0
0
A
A
S
0
1
0
0
0
0
1
A
Data
A
First byte
R/W
R/W
At this moment, master-transmitter
becomes master-receiver, and
slave-receiver becomes
slave-transmitter
NACK From
Data from Register
Master
Data
P
NA
Last Byte
Figure 8. Read From Register
<br/>
1
2
3
4
5
6
7
8
0
9
SCL
SDA
Data From Port
Data 1
Slave Address
Data From Port
Data 4
AD
DR
S
0
1
0
0
0
0
A
A
NA
P
Start
Condition
NACK From
Master
ACK From
Slave
ACK From
Master
Stop
R/W
Condition
Read From
Port
Data Into
Port
Data 2
Data 3
Data 4
Data 5
tph
tps
INT
tiv
tir
A. Transfer of data can be stopped at any time by a stop condition. When this occurs, data present at the latest
acknowledge phase is valid (output mode). It is assumed that the command byte previously has been set to 00 (read
input port register).
B. This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address
call and actual data transfer from P port (see Figure 8).
Figure 9. Read Input Port Register
11
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.5
–0.5
–0.5
–0.5
MAX
6.5
UNIT
VCCI
VCCP
VI
Supply voltage range
Supply voltage range
Input voltage range(2)
Output voltage range(2)
Input clamp current
V
6.5
6.5
6.5
±20
±20
±20
±20
50
V
V
VO
V
IIK
ADDR, RESET, SCL
VI < 0
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
IOK
Output clamp current
INT
VO < 0
P Port
SDA
VO < 0 or VO > VCCP
VO < 0 or VO > VCCI
VO = 0 to VCCP
VO = 0 to VCCI
VO = 0 to VCCP
IIOK
Input/output clamp current
Continuous output low current
Continuous output low current
Continuous output high current
Continuous current through GND
Continuous current through VCCP
Continuous current through VCCI
P Port
SDA, INT
P Port
IOL
IOH
25
50
200
160
10
ICC
PW package
RGT package
ZXY package
108
53
θJA
Package thermal impedance(3)
°C/W
°C
193
150
Tstg
Storage temperature range
–65
(1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
(3) The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions
MIN
1.65
MAX
5.5
UNIT
VCCI
Supply voltage
Supply voltage
V
VCCP
1.65
5.5
SCL, SDA
0.7 × VCCI
0.7 × VCCP
–0.5
5.5
VIH
VIL
High-level input voltage
Low-level input voltage
V
V
ADDR, P7–P0, RESET
SCL, SDA
5.5
0.3 × VCCI
ADDR, P7–P0, RESET
P7–P0
–0.5 0.3 × VCCP
IOH
IOL
TA
High-level output current
Low-level output current
Operating free-air temperature
10
25
mA
mA
°C
P7–P0
–40
85
12
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
Electrical Characteristics
over recommended operating free-air temperature range, VCCI = 1.65 V to 5.5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCCP
1.65 V to 5.5 V
1.65 V to 5.5 V
1.65 V
MIN
TYP(1)
MAX
UNIT
V
VIK
Input diode clamp voltage II = –18 mA
Power-on reset voltage(2) VI = VCCP or GND, IO = 0
–1.2
VPOR
1
1.4
V
1.2
1.8
2.6
4.1
1.1
1.7
2.5
4.0
2.3 V
IOH = –8 mA
3 V
4.5 V
P port high-level output
voltage
VOH
V
1.65 V
2.3 V
IOH = –10 mA
3 V
4.5 V
1.65 V
0.45
0.25
0.25
0.2
2.3 V
IOL = 8 mA
3 V
4.5 V
P port low-level output
voltage
VOL
V
1.65 V
0.6
2.3 V
0.3
IOL = 10 mA
3 V
0.25
0.2
4.5 V
SDA
VOL = 0.4 V
1.65 V to 5.5 V
1.65 V to 5.5 V
3
3
IOL
mA
INT
VOL = 0.4 V
15
SCL, SDA
ADDR, RESET
P port
VI = VCCI or GND
VI = VCCP or GND
VI = VCCP
±0.1
±0.1
1
II
1.65 V to 5.5 V
1.65 V to 5.5 V
µA
IIH
IIL
µA
µA
P port
VI = GND
1
VI on SDA = VCCI or GND,
VI on P port, ADDR and
RESET = VCCP or GND,
IO = 0, I/O = inputs,
3.6 V to 5.5 V
2.3 V to 3.6 V
10
20
15
SDA,
6.5
Operating
mode
P Port,
ADDR,
RESET
1.65 V to 2.3 V
4
9
fSCL = 400 kHz
VI on SDA = VCCI or GND,
VI on P port, ADDR and
RESET = VCCP or GND,
IO = 0, I/O = inputs,
3.6 V to 5.5 V
2.3 V to 3.6 V
2.5
1.6
5
SDA,
3.8
Operating
mode
P Port,
ADDR,
RESET
ICC
(ICCI + ICCP
µA
)
1.65 V to 2.3 V
1
2.3
fSCL = 100 kHz
VI on SCL and SDA = VCCI or
SCL, SDA, GND,
3.6 V to 5.5 V
2.3 V to 3.6 V
0.2
0.1
1
0.6
Standby
mode
P Port,
ADDR,
RESET
VI on P Port, ADDR and
RESET = VCCP or GND,
IO = 0, I/O = inputs,
fSCL = 0
1.65 V to 2.3 V
1.65 V to 5.5 V
1.65 V to 5.5 V
0.1
0.4
25
60
One input at VCCI – 0.6 V,
Other inputs at VCCI or GND
∆ICCI
SCL, SDA
µA
µA
Additional
current in
Standby
mode
P Port,
ADDR,
RESET
One input at VCCP – 0.6 V,
Other inputs at VCCP or GND
∆ ICCP
Ci
SCL
VI = VCCI or GND
VIO = VCCI or GND
VIO = VCCP or GND
1.65 V to 5.5 V
1.65 V to 5.5 V
6
7
7
8
pF
pF
SDA
Cio
P Port
7.5
8.5
(1) All typical values are at nominal supply voltage (1.8-V, 2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C.
(2) When power (from 0 V) is applied to VCCP, an internal power-on reset holds the TCA6408 in a reset condition until VCCP has reached
VPOR. At that time, the reset condition is released, and the TCA6408 registers and I2C/SMBus state machine initialize to their default
states. After that, VCCP must be lowered to below 0.2 V and back up to the operating voltage for a power-reset cycle.
13
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
I2C Interface Timing Requirements
over recommended operating free-air temperature range (unless otherwise noted) (see Figure 10)
STANDARD MODE
I2C BUS
FAST MODE
I2C BUS
MIN
0
UNIT
kHz
MIN
0
MAX
MAX
400
fscl
I2C clock frequency
100
tsch
tscl
I2C clock high time
I2C clock low time
I2C spike time
I2C serial data setup time
I2C serial data hold time
I2C input rise time
I2C input fall time
I2C output fall time; 10 pF to 400 pF bus
I2C bus free time between Stop and Start
I2C Start or repeater Start condition setup time
I2C Start or repeater Start condition hold time
I2C Stop condition setup time
Valid data time; SCL low to SDA output valid
4
0.6
µs
µs
ns
ns
ns
ns
ns
µs
µs
µs
µs
µs
µs
4.7
0
1.3
tsp
50
0
50
tsds
tsdh
ticr
250
0
100
0
(1)
1000
300
20 + 0.1Cb
300
300
300
(1)
(1)
ticf
20 + 0.1Cb
20 + 0.1Cb
tocf
tbuf
tsts
300
4.7
4.7
4
1.3
0.6
0.6
0.6
tsth
tsps
tvd(data)
4
1
1
1
1
Valid data time of ACK condition; ACK signal from SCL low to
SDA (out) low
tvd(ack)
µs
(1) Cb = total capacitance of one bus line in pF
Reset Timing Requirements
over recommended operating free-air temperature range (unless otherwise noted) (see Figure 13)
STANDARD MODE
I2C BUS
FAST MODE
I2C BUS
UNIT
MIN
4
MAX
MIN
4
MAX
tW
Reset pulse duration
Reset recovery time
Time to reset(1)
ns
ns
ns
tREC
tRESET
0
0
600
600
(1) Minimum time for SDA to become high or minimum time to wait before doing a START
Switching Characteristics
over recommended operating free-air temperature range, CL≤ 100 pF (unless otherwise noted) (see Figure 10)
STANDARD
FAST MODE
MODE
I2C BUS
I2C BUS
PARAMETER
FROM
TO
UNIT
MIN
MAX
4
MIN
MAX
4
tiv
Interrupt valid time
Interrupt reset delay time
Output data valid
P Port
SCL
INT
INT
µs
µs
ns
ns
ns
tir
4
4
tpv
tps
tph
SCL
P7–P0
SCL
400
400
Input data setup time
Input data hold time
P Port
P Port
0
0
SCL
300
300
14
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
TYPICAL CHARACTERISTICS
TA = 25°C (unless otherwise noted)
SUPPLY CURRENT
vs
TEMPERATURE
STANDBY SUPPLY CURRENT
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
vs
TEMPERATURE
18
16
14
12
10
8
120
100
80
60
40
20
0
18
16
14
12
10
8
fSCL = 400 kHz
fSCL = 400 kHz
SCL = VCC
All I/Os unloaded
All I/Os unloaded
All I/Os unloaded
VCC = 5.0 V
VCC = 5.0 V
VCC = 3.3 V
6
4
VCC = 2.5 V
VCC = 1.8 V
VCC = 3.3 V
2
6
0
4
VCC = 2.5 V
VCC = 1.8 V
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Supply Voltage, VCC (V)
2
0
–40 –15
10
35
60
85
–40 –15
10
35
60
85
Temperature,TA (°C)
Temperature,TA (°C)
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
30
25
20
15
10
5
60
50
40
30
20
10
70
VCC = 1.8 V
VCC = 3.3 V
VCC = 2.5 V
TA = –40°C
60
50
40
30
20
10
0
TA = –40°C
TA = –40°C
TA = 25°C
TA = 85°C
TA = 25°C
TA = 25°C
TA = 85°C
TA = 85°C
0
0.0 0.1 0.2 0.3 0.4 0.5 0.6
Output Low Voltage, VOL (V)
0
0.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.1 0.2
0.3
0.4
0.5
0.6
Output Low Voltage, VOL (V)
Output Low Voltage, VOL (V)
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
I/O LOW VOLTAGE
vs
TEMPERATURE
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
90
80
70
60
50
40
30
20
10
0
30
300
250
200
150
100
50
VCC = 5.0 V
VCC = 1.8 V
25
20
15
10
5
VCC = 1.8 V, ISOURCE = 10 mA
TA = –40°C
TA = –40°C
TA = 25°C
TA = 25°C
VCC = 5.0 V, ISOURCE = 10 mA
TA = 85°C
TA = 85°C
VCC = 1.8 V, ISOURCE = 1 mA
VCC = 5 V, ISOURCE = 1 mA
0
0.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.1
0.2
0.3
0.4
0.5
0.6
VCCP – VOH (V)
Output Low Voltage, VOL (V)
0
–40 –15
10
35
60
85
Temperature,TA (°C)
15
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
TYPICAL CHARACTERISTICS (continued)
TA = 25°C (unless otherwise noted)
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
50
45
40
35
30
25
20
15
10
5
70
60
50
40
30
20
10
0
90
80
70
60
50
40
30
20
10
0
VCC = 3.3 V
VCC = 2.5 V
VCC = 5.0 V
TA = –40°C
TA = –40°C
TA = –40°C
TA = 25°C
TA = 25°C
TA = 25°C
TA = 85°C
TA = 85°C
TA = 85°C
0
0.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.0
0.1
0.2 0.3
VCCP – VOH (V)
0.4
0.5
0.6
0.1
0.2
0.3
0.4
0.5
0.6
VCCP – VOH (V)
VCCP – VOH (V)
I/O HIGH VOLTAGE
vs
TEMPERATURE
300
250
200
150
100
50
VCC = 1.8 V, ISOURCE = 10 mA
VCC = 5.0 V, ISOURCE = 10 mA
0
–40 –15
10
35
60
85
Temperature,TA (°C)
16
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
PARAMETER MEASUREMENT INFORMATION
V
CCI
R
= 1 kW
L
SDA
DUT
C
= 50 pF
L
(see Note A)
SDA LOAD CONFIGURATION
Two Bytes for READ Input Port Register
(see Figure 9)
Stop
Start
Address
Bit 7
(MSB)
Data
Bit 7
(MSB)
Data
Bit 0
(LSB)
Stop
Condition
(P)
R/W
Bit 0
(LSB)
ACK
(A)
Address
Bit 1
Condition Condition
(P) (S)
t
t
sch
scl
0.7 ´ V
CCI
SCL
SDA
0.3 ´ V
CCI
t
t
icr
vd
t
t
sts
sp
t
t
icf
t
buf
vd
t
t
sps
ocf
0.7 ´ V
0.3 ´ V
CCI
CCI
t
t
vd(ack)
icr
t
sdh
t
t
icf
sds
t
sth
Repeat Start
Condition
Stop
Condition
VOLTAGE WAVEFORMS
BYTE
DESCRIPTION
I2C address
1
2
Input register port data
A. CL includes probe and jig capacitance. tocf is measured with CL of 10 pF or 400 pF.
B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C. All parameters and waveforms are not applicable to all devices.
Figure 10. I2C Interface Load Circuit and Voltage Waveforms
17
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
PARAMETER MEASUREMENT INFORMATION (continued)
V
CCI
R
= 4.7 kW
L
INT
DUT
C
= 100 pF
L
(see Note A)
INTERRUPT LOAD CONFIGURATION
ACK
From Slave
ACK
Start
8 Bits
From Slave
Condition
R/W
1
(One Data Byte)
From Port
Slave Address
Data From Port
Data 2
AD
DR
Data 1
A
1
P
S
0
1
0
3
0
4
0
0
6
A
A
1
2
5
7
8
A
t
B
B
ir
t
ir
INT
A
t
iv
t
sps
A
Data
Into
Port
Address
Data 1
Data 2
0.7 ´ V
CCI
CCI
0.5 ´ V
SCL
INT
CCI
R/W
A
0.3 ´ V
t
iv
t
ir
0.5 ´ V
INT
CCI
Pn
0.5 ´ V
CCP
View A−A
A. CL includes probe and jig capacitance.
View B−B
B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C. All parameters and waveforms are not applicable to all devices.
Figure 11. Interrupt Load Circuit and Voltage Waveforms
18
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
PARAMETER MEASUREMENT INFORMATION (continued)
Pn
500 W
DUT
2 ´ V
CCP
C
= 50 pF
L
(see Note A)
500 W
P PORT LOAD CONFIGURATION
0.7 ´ V
0.3 ´ V
CCP
CCI
SCL
P0
A
P3
Slave
ACK
SDA
Pn
t
pv
(see Note B)
Last Stable Bit
Unstable
Data
WRITE MODE (R/W = 0)
0.7 ´ V
0.3 ´ V
CCI
SCL
Pn
P0
A
P3
CCI
t
ph
t
ps
0.5 ´ V
CCP
READ MODE (R/W = 1)
A. CL includes probe and jig capacitance.
B. tpv is measured from 0.7 × VCC on SCL to 50% I/O (Pn) output.
C. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. All parameters and waveforms are not applicable to all devices.
Figure 12. P Port Load Circuit and Timing Waveforms
19
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
PARAMETER MEASUREMENT INFORMATION (continued)
V
CCI
R
= 1 kW
L
Pn
500 W
SDA
DUT
2 ´ V
CCP
DUT
C = 50 pF
L
(see Note A)
C
= 50 pF
500 W
L
(see Note A)
SDA LOAD CONFIGURATION
P PORT LOAD CONFIGURATION
Start
SCL
ACK or Read Cycle
SDA
0.3 ´ V
CCI
t
RESET
V
/2
RESET
CCP
t
t
REC
REC
t
W
V
/2
Pn
CCP
t
RESET
A. CL includes probe and jig capacitance.
B. All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C. The outputs are measured one at a time, with one transition per measurement.
D. I/Os are configured as inputs.
E. All parameters and waveforms are not applicable to all devices.
Figure 13. Reset Load Circuits and Voltage Waveforms
20
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
APPLICATION INFORMATION
Figure 14 shows an application in which the TCA6408 can be used.
V
V
CCI
CCP
16
V
CCI
(1.8 V)
1
10 kW
(x 4)
V
CC
100 kW (x 3)
V
V
CCP
CCI
14
15
SCL
SCL
ALARM
(see note D)
Master
Controller
4
P0
SDA
INT
SDA
Subsystem 1
(e.g., Alarm)
13
3
INT
GND
RESET
RESET
A
5
P1
TCA6408
ENABLE
B
6
P2
P3
P4
P5
P6
P7
2
ADDR
7
9
Keypad
10
11
12
GND
8
A. Device address configured as 0100000 for this example.
B. P0 and P2–P4 are configured as inputs.
C. P1 and P5-P7 are configured as outputs.
D. Resistors are required for inputs (on P port) that may float. If a driver to an input will never let the input float, a
resistor is not needed. Outputs (in the P port) do not need pullup resistors.
Figure 14. Typical Application
21
Submit Documentation Feedback
TCA6408
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
www.ti.com
SCPS151C–FEBRUARY 2007–REVISED JUNE 2007
APPLICATION INFORMATION (continued)
Minimizing ICC When the I/O is Used to Control LEDs
When the I/Os are used to control LEDs, normally they are connected to VCC through a resistor as shown in
Figure 14. The LED acts as a diode so when the LED is off the I/O VIN is about 1.2 V less than VCC. The ∆ICC
parameter in "Electrical Characteristics" shows how ICC increases as VIN becomes lower than VCC. Designs
needing to minimize current consumption, such as battery power applications, should consider maintaining the
I/O pins greater than or equal to VCC when the LED is off.
Figure 15 shows a high-value resistor in parallel with the LED. Figure 16 shows VCC less than the LED supply
voltage by at least 1.2 V. Both of these methods maintain the I/O VIN at or above VCC and prevent additional
supply current consumption when the LED is off.
VCC
LED
100 kΩ
VCC
Px
Figure 15. High-Value Resistor in Parallel With the LED
3.3 V
5 V
LED
VCC
Px
Figure 16. Device Supplied by a Low Voltage
22
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2007
PACKAGING INFORMATION
Orderable Device
TCA6408PW
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
TSSOP
PW
16
16
16
16
16
16
90 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TCA6408PWG4
TCA6408PWR
TSSOP
TSSOP
TSSOP
QFN
PW
PW
90 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TCA6408PWRG4
TCA6408RGTR
TCA6408RGTRG4
PW
2000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
RGT
RGT
3000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
QFN
3000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Sep-2007
TAPE AND REEL BOX INFORMATION
Device
Package Pins
Site
Reel
Reel
A0 (mm)
B0 (mm)
K0 (mm)
P1
W
Pin1
Diameter Width
(mm) (mm) Quadrant
(mm)
330
(mm)
12
TCA6408PWR
TCA6408RGTR
PW
16
16
SITE 41
SITE 41
7.0
3.3
5.6
3.3
1.6
1.1
8
8
12
12
Q1
Q2
RGT
330
12
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
24-Sep-2007
Device
Package
Pins
Site
Length (mm) Width (mm) Height (mm)
TCA6408PWR
TCA6408RGTR
PW
16
16
SITE 41
SITE 41
346.0
346.0
346.0
346.0
0.0
0.0
RGT
Pack Materials-Page 2
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
M
0,10
0,65
14
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°–8°
A
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
8
14
16
20
24
28
DIM
3,10
2,90
5,10
4,90
5,10
4,90
6,60
6,40
7,90
9,80
9,60
A MAX
A MIN
7,70
4040064/F 01/97
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Applications
Audio
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/audio
Automotive
Broadband
Digital Control
Military
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
interface.ti.com
logic.ti.com
Logic
Power Mgmt
Microcontrollers
RFID
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lpw
Telephony
Low Power
Wireless
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated
相关型号:
TCA6408PWRG4
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6408RGTR
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6408RGTRG4
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6408ZXYR
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6408_09
LOW-VOLTAGE 8-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6416
LOW-VOLTAGE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6416A
LOW-VOLTAGE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6416APWR
LOW-VOLTAGE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6416ARTWR
LOW-VOLTAGE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6416AZQSR
LOW-VOLTAGE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6416A_11
LOW-VOLTAGE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
TCA6416PW
LOW-VOLTAGE 16-BIT I2C AND SMBus I/O EXPANDER WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
TI
©2020 ICPDF网 联系我们和版权申明