TCA9511ADGKR [TI]
2 位双向 2.3V 至 5.5V 热插拔 400kHz I2C/SMBus 缓冲器 | DGK | 8 | -40 to 125;![TCA9511ADGKR](http://pdffile.icpdf.com/pdf2/p00366/img/icpdf/TCA9511A_2237462_icpdf.jpg)
型号: | TCA9511ADGKR |
厂家: | ![]() |
描述: | 2 位双向 2.3V 至 5.5V 热插拔 400kHz I2C/SMBus 缓冲器 | DGK | 8 | -40 to 125 光电二极管 接口集成电路 |
文件: | 总26页 (文件大小:1287K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
TCA9511A
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
TCA9511A 热插拔 I2C 总线和 SMBus 缓冲器
1 特性
3 说明
•
•
支持 I2C 总线信号的双向数据传输
工作电源电压范围为 2.3V 至 5.5V
TCA9511A 是一款热插拔 I2C 总线缓冲器,支持将 I/O
卡插入带电背板中,而不会损坏数据和破坏时钟线路。
控制电路可防止背板侧 I2C 线路(输入)与板卡侧 I2C
线路(输出)相连接(直到背板上出现停止命令或总线
空闲情况为止),而不会在板卡上发生总线争用的情
况。当建立连接时,该器件可提供双向缓冲,从而使背
板及板卡电容保持隔离。在插入过程中,会对 SDA 和
SCL 线路预充电至 1V,从而尽可能减小对器件的寄生
电容充电所需的电流。
• -40°C 至 125°C 的 TA 环境空气
温度范围
•
对所有 SDA 和 SCL 线路的 1V 预充电可防止带电
板插入过程中发生损坏
可适应标准模式及快速模式 I2C 器件
支持时钟展宽、仲裁及同步
断电高阻抗 I2C 引脚
•
•
•
当 I2C 总线空闲时,可通过将 EN 引脚设置为低电平将
TCA9511A 置于关断模式,从而降低功耗。当 EN 被
拉高时,TCA9511A 将恢复正常运行。该器件还包括
一个开漏 READY 输出引脚,该引脚负责在背板与板卡
侧相连时发出指示信号。当 READY 引脚为高电平时,
SDAIN 和 SCLIN 被连接至 SDAOUT 和 SCLOUT。当
两侧断开时,READY 引脚为低电平。
2 应用
•
•
•
•
•
服务器
企业交换
电信交换设备
基站
工业自动化设备
器件信息
封装(1)
封装尺寸(标称值)
器件型号
TCA9511A
VSSOP (8)
3.00mm × 3.00mm
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
简化版原理图
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SCPS272
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
Table of Contents
8.4 Device Functional Modes..........................................10
9 Application Information Disclaimer.............................12
9.1 Application Information............................................. 12
9.2 Typical Application.................................................... 12
9.3 Typical Application on a Backplane.......................... 15
10 Power Supply Recommendations..............................17
10.1 Power Supply Best Practices..................................17
10.2 Power-on Reset Requirements...............................17
11 Layout...........................................................................18
11.1 Layout Guidelines................................................... 18
11.2 Layout Example...................................................... 19
12 Device and Documentation Support..........................20
12.1 Receiving Notification of Documentation Updates..20
12.2 支持资源..................................................................20
12.3 Trademarks.............................................................20
12.4 静电放电警告.......................................................... 20
12.5 术语表..................................................................... 20
13 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings ....................................... 4
6.2 ESD Ratings .............................................................. 4
6.3 Recommended Operating Conditions ........................4
6.4 Thermal Information ...................................................4
6.5 Electrical Characteristics ............................................5
6.6 Timing Requirements .................................................5
6.7 Switching Characteristics ...........................................6
6.8 Typical Characteristics................................................7
7 Parameter Measurement Information............................8
8 Detailed Description........................................................9
8.1 Overview.....................................................................9
8.2 Functional Block Diagram...........................................9
8.3 Feature Description...................................................10
Information.................................................................... 20
4 Revision History
注:以前版本的页码可能与当前版本的页码不同
Changes from Revision B (March 2020) to Revision C (January 2021)
Page
• Deleted the Device Comparision Table ..............................................................................................................3
• Changed the VCC pin recommended capacitance From: 0.01 μF To: 0.1 μF to match typical application
section................................................................................................................................................................ 3
• Changed HBM ESD from 1500 V to 3500 V.......................................................................................................4
• Changed ICC values from 6 mA max to 4.5 mA, and typical improved to 2.5 mA............................................ 5
• Changed VOS typical from 50 mV to 60 mV.......................................................................................................5
Changes from Revision A (December 2019) to Revision B (March 2020)
Page
• Changed pin 7 From: SDAOUTL To: SDAOUT.................................................................................................. 3
• Changed text From: "pulled to roughly 160 mV." To: "pulled to roughly 150 mV" in the Bus active section..... 11
• Changed the device number of 图 11-1 to TCA9511A .....................................................................................19
Changes from Revision * (October 2019) to Revision A (December 2019)
Page
•
将器件状态从预告信息 更改为量产 数据.............................................................................................................1
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
5 Pin Configuration and Functions
VCC
EN
SCLOUT
SCLIN
1
2
3
4
8
7
6
5
SDAOUT
SDAIN
READY
GND
Not to scale
图 5-1. 8-Pin VSSOP, DGK Package (Top View)
表 5-1. Pin Functions
PIN
I/O
DESCRIPTION
NAME
NO.
Active-high chip enable pin. If EN is low, the TCA9511A is in a low current mode. It also
disables the rise-time accelerators, disables the bus pre-charge circuitry, drives READY low,
isolates SDAIN from SDAOUT and isolates SCLIN from SCLOUT. EN should be high (at
VCC) for normal operation. Connect EN to VCC if this feature is not being used.
EN
1
I
SCLOUT
SCLIN
GND
2
3
4
I/O
I/O
-
Serial clock output. Connect this pin to the SCL bus on the card.
Serial clock input. Connect this pin to the SCL bus on the backplane.
Supply ground
Connection flag/rise-time accelerator control. Ready is low when either EN is low or the
start-up sequence has not been completed. READY goes high when EN is high and start-up
is complete. Connect a 10-kΩ resistor from this pin to VCC to provide the pull-up current.
READY
5
O
SDAIN
6
7
I/O
I/O
Serial data input. Connect this pin to the SDA bus on the backplane.
Serial data output. Connect this pin to the SDA bus on the card.
SDAOUT
Supply Power. Main input power supply from backplane. This is the supply voltage for the
devices on the backplane I2C buses. Connect pull-up resistors from SDAIN and SCLIN (and
also from SDAOUT and SCLOUT) to this supply. It is recommended to place a bypass
capacitor of 0.1 μF close to this pin for best results.
VCC
8
-
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
6 Specifications
6.1 Absolute Maximum Ratings
Over operating free-air temperature range (unless otherwise noted)(1)
MIN
–0.5
–0.5
–0.5
MAX
UNIT
V
VCC
7
7
Input
Voltage
SDAIN, SCLIN, SDAOUT, SCLOUT
V
EN, READY
7
V
IIK
Input clamp current
Output clamp current
VI < 0
mA
mA
–50
–50
IOK
VO < 0
SDAIN, SDAOUT, SCLIN, SCLOUT,
EN, READY
IO
Continuous output current
±50
mA
ICC
TJ
Continuous current through VCC or GND
Maximum junction temperature
Storage temperature
±100
130
mA
°C
Tstg
150
°C
–65
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
6.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per ANSI/ESDA/
JEDEC JS-001, all pins(1)
±3500
V(ESD)
Electrostatic discharge
V
Charged device model (CDM), per JEDEC
specification JESD22-C101, all pins(2)
±1000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process
6.3 Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted)
MIN
MAX UNIT
VCC
VI
Supply voltage
2.3
0
5.5
Input voltage range
Input/output voltage range
Output voltage range
Ambient temperature
EN input
5.5
V
5.5
VIO
VO
TA
SDAIN, SCLIN, SDAOUT, SCLOUT
READY
0
0
5.5
125
°C
–40
6.4 Thermal Information
TCA9511
THERMAL METRIC(1)
DGK
8 Pin
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
177.1
64.5
99.6
9.5
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
ΨJT
97.9
N/A
ΨJB
RθJC(bot)
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
6.5 Electrical Characteristics
Over operating free-air temperature range (unless otherwise noted). Typical specifications are at TA = 25 °C, VCC = 3.3 V,
unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
POWER SUPPLY
VCC = 5.5V
ICC
Supply current
SDAIN, SCLIN = 0V
2.5
4.5
mA
SDAOUT, SCLOUT = 10k RPU
EN = 0 V
SDAIN, SCLIN, SDAOUT, SCLOUT = 0V
Supply current in shutdown mode through or VCC
ISD
5
30
µA
the VCC pin(1)
READY pin = Hi-Z
EN pulled low after bus connection event
(disable precharge)
Under voltage lockout (rising)
Under voltage lockout (falling)
2.1
2
V
V
EN = VCC
READY = 10 kΩ to VCC
UVLO
START-UP CIRCUITRY
VPRE
Pre-charge voltage
SDA, SCL = Hi-Z
0.8
2
1
5
1.2
V
RISE-TIME ACCELERATORS
Position transition on SDA, SCL
VSDA/SCL = 0.6 V, Slew rate = 1.25 V/µs.
VCC = 3.3 V
IPU
INPUT-OUTPUT CONNECTION
RTA pull-up current(2)
mA
SDA/SCL pins = 90% VCC, EN = VCC
GND
SDA/SCL pins = 10% VCC, EN = GND
,
ILI
Input pin leakage
-1
-1
1
µA
Input-output offset voltage (SCLIN to
SCLOUT, SCLOUT to SCLIN and SDAIN
to SDAOUT, SDAOUT to SDAIN
VOS
60
100
1
mV
µA
RPU for SDA/SCL = 10 kΩ
EN = VCC, READY = VCC, Bus
connected
II_RDY
Ready pin leakage
DIGITAL IO THRESHOLD
0.7 ×
VCC
VIH
VIL
High-level input voltage
EN
EN
VCC
0.3 ×
VCC
Low-level input voltage
0
V
SDAIN, SCLIN, SDAOUT, SCLOUT
IOL = 4 mA
VIN = 0.1 V
0.15
0.4
0.4
VOL
Low-level output voltage
READY
IOL = 3 mA
0
DYNAMIC CHARACTERISTICS
VEN = 0 V or VCC
f = 400 kHz
CIN (EN)
EN input capacitance
1.6
7
4
10
10
CIO
VREADY = 0 V or VCC
f = 400 kHz
READY output capacitance
SDA/SCL pin capacitance
pF
(READY)
CIO (SDA/
VPIN = 0 V or VCC
f = 400 kHz
5
SCL)
(1) In shutdown mode there will also be current flowing from VCC through the ready pin as this pin is pulled down to indicate the bus is
disconnected.
(2) Determined by design, not tested in production.
6.6 Timing Requirements
MIN
NOM
MAX
UNIT
fSCL_MAX Maximum SCL clock frequency
Copyright © 2021 Texas Instruments Incorporated
400
kHz
Submit Document Feedback
5
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
6.6 Timing Requirements (continued)
MIN
1.3
0.6
0.6
0.6
0
NOM
MAX
UNIT
µs
(1)
tBUF
Bus free time between a STOP and START condition
Hold time for a repeated START condition
Set-up time for a repeated START condition
Set-up time for a STOP condition
Data hold time
(1)
(1)
(1)
(1)
(1)
tHD;STA
tSU;STA
tSU;STO
tHD;DAT
tSU;DAT
µs
µs
µs
ns
Data set-up time
100
1.3
0.6
ns
(1)
tLOW
LOW period of the SCL clock
µs
(1)
tHIGH
HIGH period of the SCL clock
µs
20 ×
(VCC/5.5
V)
(1)
tf
Fall time of both SDA and SCL signals
Rise time of both SDA and SCL signals
300
300
ns
ns
20 ×
(VCC/5.5
V)
(1)
tr
(1) These are system-level timing specs and are dependent upon bus capacitance and pull up resistor value. It is up to the system
designer to ensure they are met
6.7 Switching Characteristics
Over operating free-air temperature range (unless otherwise noted). Typical specifications are at TA = 25 °C, VCC = 3.3 V,
unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
START-UP CIRCUITRY
tPRECHAR
SDA,SCL = Hi-Z
EN = VCC, GND
Time from VCC to precharge enabled
Time from VPOR to digital being ready
15
35
60
95
µs
µs
GE
VCC transition from 0V to VCC
Time from VPORR to earliest stop bit
recongized
tEN
SDA,SCL = 10 kΩ to VCC
EN = VCC
Measured at 0.5 × VCC
tIDLE
Bus idle time to READY active
95
30
150
200
2
µs
ns
µs
µs
SDA,SCL = 10 kΩ to VCC
READY = 10 kΩ to VCC
Measured at 0.5 × VCC
tDISABLE Time from EN high to low to READY low
SDA,SCL = 10 kΩ to VCC
READY = 10 kΩ to VCC
Measured at 0.5 × VCC
SDAIN to READY delay after stop
condition
tSTOP
1.2
0.8
SDA,SCL = 10 kΩ to VCC
READY = 10 kΩ to VCC
Measured at 0.5 × VCC
tREADY
INPUT-OUTPUT CONNECTION
tPLZ Low to high propagation delay
SCLOUT/SDAOUT to READY
1.5
RPU for SDA/SCL = 10 kΩ
CL = 100 pF per pin
Measured at 0.5 × VCC
0
10
ns
ns
RPU for SDA/SCL = 10 kΩ
CL = 100 pF per pin
tPZL
High to low propagation delay
70
150
Measured at 0.5 × VCC
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
6.8 Typical Characteristics
4
4
3.5
3
2.3 V
2.5 V
3.3 V
5 V
-40 °C
25 °C
85 °C
125 °C
3.5
3
5.5 V
2.5
2
2.5
2
1.5
1
1.5
1
-40
-15
10
35 60
Temperature (°C)
85
110
130
2
2.5
3
3.5
VCC (V)
4
4.5
5
5.5
图 6-1. ICC vs Temperature
图 6-2. ICC vs VCC
200
200
175
150
125
100
75
-40 C
25 C
85 C
105 C
125 C
-40 C
25 C
85 C
105 C
125 C
175
150
125
100
75
50
50
25
25
0
0
0.5
1
1.5
2
2.5
3
3.5
4
0.5
1
1.5
2
2.5
3
3.5
4
IOL (mA)
IOL (mA)
图 6-3. VOS vs IOL (VCC = 2.3 V, VI = 0 V)
图 6-4. VOS vs IOL (VCC = 3.3 V, VI = 0 V)
200
-40 C
25 C
85 C
105 C
125 C
175
150
125
100
75
50
25
0
0.5
1
1.5
2
2.5
3
3.5
4
IOL (mA)
图 6-5. VOS vs IOL (VCC = 5.5 V, VI = 0 V)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
7 Parameter Measurement Information
SDAn/SCLn
tEN
ENABLE
tIDLE(READY)
tDIS
READY
图 7-1. Timing for tEN, tIDLE(READY), and tDIS
SDAIN
SCLIN
SCLOUT
SDAOUT
tEN
ENABLE
READY
tSTOP
图 7-2. Timing for tSTOP
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
8 Detailed Description
8.1 Overview
The TCA9511A is a hot-swappable I2C bus buffer that supports I/O card insertion into a live backplane without
corruption of the data and clock buses. Control circuitry prevents the backplane from being connected to the
card until a stop command or bus idle condition occurs on the backplane without bus contention on the card.
When the connection is made, this device provides bidirectional buffering, keeping the backplane and card
capacitances isolated. During insertion, the SDA and SCL lines are pre-charged to 1 V to minimize the current
required to charge the parasitic capacitance of the device.
When the I2C bus is idle, the TCA9511A is put into shutdown mode by setting the EN pin low. When EN is high,
the TCA9511A resumes normal operation. It also includes an open drain READY output pin, which indicates that
the backplane and card sides are connected together. When READY is high, the SDAIN and SCLIN are
connected to SDAOUT and SCLOUT. When the two sides are disconnected, READY is low.
8.2 Functional Block Diagram
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
8.3 Feature Description
8.3.1 Hot bus insertion
During a hot bus insertion event, the TCA9511A keeps the buses disconnected to ensure that no data corruption
occurs on either bus. Once the buses are idle or a stop bit on the IN side is detected, the TCA9511A connects
the buses and READY goes high.
8.3.2 Pre-charge voltage
Both the SDA and SCL pins feature a 1-V pre-charge circuit through an internal 100 kΩ resistor prior to the pins
being connected to an I2C bus. This feature helps minimize disruptions as a result of a hot bus insertion event.
8.3.3 Rise time accelerators
The TCA9511A features a rise time accelerator (RTA) on all I2C pins that during a positive bus transition,
switches on a current source to quickly slew the bus pins high. This allows the use of weaker pull-up resistors,
which can lower VOLs and lower power system level power consumption.
8.3.4 Bus ready output indicator
The READY pin is an open drain output that provides an indicator to whether the buses are connected and
ready for traffic. This pin is pulled low when the connection between IN/OUT is high impedance. Once the bus is
idle or a stop condition on the IN side is detected, and the connection between IN/OUT is made, the READY pin
is released and pulled high by an external pull-up resistor, signaling that it is ready for traffic.
8.3.5 Powered-off high impedance for I2C and I/O pins
When the supply voltage is below the UVLO threshold, the I2C and digital I/O pins are a high impedance state to
prevent leakage currents from flowing through the device. When the EN pin is taken low, the device enters an
isolation state, presenting a high impedance on all bus pins and pulling the READY pin low.
8.3.6 Supports clock stretching and arbitration
The TCA9511A supports full clock stretching, and arbitration without lock up.
8.4 Device Functional Modes
8.4.1 Start-up and precharge
When the TCA9511A first receives power on the VCC pin, either during power-up or during live insertion, it starts
in an under voltage lockout (UVLO) state, ignoring any activity on the SDA and SCL pins until VCC rises above
UVLO.
Once the ENABLE pin goes high, the ‘Stop Bit and Bus Idle’ detect circuit is enabled and the device enters
the bus idle state.
When VCC rises above UVLO, the precharge circuitry will activate, which biases the bus pins on both sides to
about 1 V through an internal 100 kΩ resistor.
8.4.2 Bus idle
After the Stop Bit and Bus Idle detect circuits are enabled the device enters the bus idle state. The pre-charge
circuitry becomes active and forces 1 V through 100 kΩ nominal resistors to the SCL and SDA pins. The pre-
charge circuitry minimizes the voltage differential seen by the SCL/SDA pins during a hot insertion event. This
minimizes the amount of disturbance seen by the I/O card.
The device waits for the SDAIN and SCLIN pins to be high for the bus idle time or a STOP condition to be
observed on the IN pins. The SDAOUT and SCLOUT pins must be high and the SDAIN and SCLIN pins must
meet 1 of the 2 qualifiers (idle timer or a STOP condition) before connecting SDAIN to SDAOUT and SCLIN to
SCLOUT. Once the bus connections have been made, the pre-charge circuitry is disabled and the device enters
the bus active state.
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
8.4.3 Bus active
In the bus active mode, the I2C IN and OUT pins are connected, and the input is passed bi-directionally from
IN/OUT side of the bus to the OUT/IN side respectively. The buses remain connected until the EN pin is taken
low.
When the bus is connected, the driven-low side of the device is reflected on the opposite side, but with a small
offset voltage. For example, if the input is pulled low to 100 mV, the output side will be pulled to roughly 150 mV.
This offset allows the device to determine which side is currently being driven and avoid getting stuck low.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
9 Application Information Disclaimer
Note
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
9.1 Application Information
The typical application is to place the TCA9511A on the card that is being inserted or connected to a live bus,
rather than being placed on the live bus. The reason for this is to provide maximum benefit by ensuring that the
bus stays disconnected until an idle condition or stop condition is seen.
9.2 Typical Application
VCC 3.3 V
C1
0.1 µF
R1
10 k
R2
10 k
R3
10 k
R4
10 k
R5
10 k
R6
10 k
8
VCC
3
2
SCLIN
SCLOUT
6
1
7
5
SDAIN
SDAOUT
ENABLE
READY
GND
4
C2
0.1 µF
图 9-1. General Application Schematic
9.2.1 Design Requirements
9.2.1.1 Series connections
It is possible to have multiple buffers in series, but care must be taken when designing a system.
2-wire system 1
2-wire system 2
VCC = 5 V
VCC
C1
0.1 µF
C1
0.1 µF
R4
10 k
R4
10 k
R4
10 k
R4
10 k
R4
R4
R4
10 k
R4
10 k
R4
10 k
R4
10 k
5.1 k 5.1 k
C1
0.01 µF
C1
0.01 µF
VCC
VCC
EN
SDAOUT
SDAOUT
SCLOUT
READY
EN
SDAIN
SCLIN
SDA1
SDAIN
SCLIN
SCLOUT
READY
SDA1
SCL1
SCL1
GND
GND
To other
To other
system 1 devices
system 2 devices
Long
distance bus
图 9-2. Series Buffer Connections
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
Each buffer adds approximately 60 mV of offset. Maximum offset (VOFFSET) should be considered. The low level
at the signal origination end is dependent upon bus load. The I2C-bus specification requires that a 3 mA current
produces no larger than a 0.4 V VOL. As an example, if the VOL at the master is 0.1 V, and there are 4 buffers in
series (each adding about 60 mV), then the VOL at the farthest buffer is approximately 0.34 V. This device has a
rise time accelerator (RTA) that activates at 0.6 V. With great care, a system with 4 buffers may work, but as the
VOL moves up, it may be possible to trigger the RTA, creating a false edge on the clock.
It is recommended to limit the number of buffers in series to two, and to keep the load light to minimize the offset.
Another special consideration of series connections is the effect on round-trip-delay. This is the sum of
propagation delays through the buffers and any effects on rise time. It is possible that fast mode speeds (400
kHz) are not possible due to delays and bus loading.
9.2.1.2 Multiple connections to a common node
It is possible to have multiple buffers in connect to a common node, but care must be taken when designing a
system.
Buffer A
Buffer B
Buffer C
Master
Slave B
Slave C
Common
node
图 9-3. Connections to Common Node
It is important to try and avoid common node architectures. The multiple nodes sharing a common node can
create glitches if the output voltage from a master slave device plus the offset voltage of the buffer are high
enough to trip the RTA. Also keep in mind that the VOS must be crossed in order for a device to begin to regulate
the other side.
Consider a system with three buffers connected to a common node and communication between the Master and
Slave B that are connected at either end of buffer A and buffer B in series as shown in 图 9-3. Consider if the
VOL at the input of buffer A is 0.3 V and the VOL of Slave B (when acknowledging) is 0.36 V with the direction
changing from Master to Slave B and then from Slave B to Master. Before the direction change the user should
observe VIL at the input of buffer A of 0.3 V and its output, the common node, is ~0.36 V. The output of buffer B
and buffer C would be ~0.42 V, but Slave B is driving 0.4 V, so the voltage at Slave B is 0.4 V. The output of
buffer C is ~0.52 V. When the Master pull-down turns off, the input of buffer A rises and so does its output, the
common node, because it is the only part driving the node. The common node rises to ~0.5 V before the buffer B
output turns on, if the pull-up is strong the node may bounce. If the bounce goes above the threshold for the
rising edge accelerator ~0.6 V, the accelerators on both buffer A and buffer C will fire, contending with the output
of buffer B. The node on the input of buffer A goes high as will the input node of buffer C. After the common
node voltage is stable for a while, the rising edge accelerators turn off, and the common node returns to ~0.5 V
because the buffer B is still on. The voltage at both the Master and Slave C nodes then fall to ~0.6 V until Slave
B turned off. This does not cause a failure on the data line as long as the return to 0.5 V on the common node
(~0.56 V at the Master and Slave C) occurred before the data setup time. If this were the SCL line, the parts on
buffer A and buffer C would see a false clock rather than a stretched clock, which causes a system error.
9.2.1.3 Propagation delays
The delay for a rising edge is determined by the combined pull-up current from the bus resistors and the rise
time accelerator current source and the effective capacitance on the lines. If the pull-up currents are the same,
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
any difference in rise time is directly proportional to the difference in capacitance between the two sides. The
tPLH may be negative if the output capacitance is less than the input capacitance and would be positive if the
output capacitance is larger than the input capacitance, when the currents are the same.
The tPHL can never be negative because the output does not start to fall until the input is below 0.7 × VCC, the
output turn on has a non-zero delay, and the output has a limited maximum slew rate. Even if the input slew rate
is slow enough that the output catches up, it would still lag the falling voltage of the input by the offset voltage.
The maximum tPHL occurs when the input is driven low with a very fast slew rate and the output is still limited by
its turn-on delay and the falling edge slew rate.
9.2.2 Detailed Design Procedure
The system pull-up resistors must be strong enough to provide a positive slew rate of 1.25 V/µs on the SDA and
SCL pins, in order to activate the boost pull-up currents during rising edges. Choose maximum resistor value
using the formula given in 方程式 1.
VCC(MIN ) F 0.6
R Q 800 × 103 l
p
C
(1)
where R is the pull-up resistor value in Ω, VCC(MIN) is the minimum VCC voltage in volts, and C is the equivalent
bus capacitance in picofarads (pF).
In addition, regardless of the bus capacitance, always choose RPU ≤ 65.7 kΩ for VCC = 5.5 V, RPU ≤ 45 kΩ for
VCC = 3.3 V, and RPU ≤ 33 kΩ for VCC = 2.5 V. The start-up circuitry requires logic HIGH voltages on SDAOUT
and SCLOUT to connect the backplane to the card, and these pull-up values are needed to overcome the pre-
charge voltage.
9.2.3 Application Curves
50
40
30
20
10
0
70
60
50
40
30
20
10
0
RPU
(kꢀ)
RPU
(kꢀ)
RMAX = 65.7 kꢀ
RMAX = 45 kꢀ
Rise time = 300 ns(2)
Rise time = 20 ns
Rise time = 300 ns(2)
RMIN = 1 kꢀ
0
100
200
300
400
Cb (pF)
Rise time = 20 ns
Test
Test
Test
RMIN = 1.7 kꢀ
0
100
200
300
400
Cb (pF)
图 9-4. Example Bus Requirements for 3.3 V
图 9-5. Example Bus Requirements for 5 V Systems
Systems
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
9.3 Typical Application on a Backplane
As shown in 图 9-6, the TCA9511A is used in a backplane connection. The TCA9511A is placed on the I/O
peripheral card and connects the I2C devices on the card to the backplane safely upon a hot insertion event.
Note that if the I/O cards were plugged directly into the backplane, all of the backplane and card capacitances
would add directly together, making rise time and fall time requirements difficult to meet. Placing a bus buffer on
the edge of each card; however, isolates the card capacitance from the backplane. For a given I/O card, the
TCA9511A drives the capacitance of everything on the card and the backplane must drive only the capacitance
of the bus buffer, which is less than 10 pF, the connector, trace, and all additional cards on the backplane.
Backplane
Connector
Backplane
I/O Peripheral Card 1
C1
Power Supply
Hot Swap
VCC
R1
10 k
R2
10 k
R3
10 k
R4
10 k
R5
10 k
R6
10 k
0.1 µF
BD_SEL
VCC
TCA9511
GND
CARD1_SDA
CARD1_SCL
EN
SDAOUT
SCLOUT
READY
SDAIN
SCLIN
SDA
SCL
I/O Peripheral Card 2
C3
Power Supply
Hot Swap
R7
10 k
R8
10 k
R9
10 k
R10
10 k
0.1 µF
VCC
TCA9511
GND
CARD2_SDA
CARD2_SCL
EN
SDAOUT
SCLOUT
READY
SDAIN
SCLIN
I/O Peripheral Card N
C5
Power Supply
Hot Swap
R11
10 k
R12
10 k
R13
10 k
R14
10 k
0.1 µF
VCC
TCA9511
GND
CARDN_SDA
CARDN_SCL
EN
SDAOUT
SCLOUT
READY
SDAIN
SCLIN
图 9-6. Backplane Application Schematic
9.3.1 Design Requirements
There are a few considerations when using these hot swap buffers. It is NOT recommended to place the
TCA9511A on the backplane connector as it cannot isolate the cards from one another which will possibly result
in disturbing on-going I2C transactions. Instead, place the TCA9511A on the I/O peripheral card to maximize
benefit.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
9.3.2 Detailed Design Procedure
The design procedure is the same as outlined in 节 9.2.2.
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
10 Power Supply Recommendations
10.1 Power Supply Best Practices
In order for the pre-charge circuitry to dampen the effect of hot-swap insertion of the TCA9511A into an active
I2C bus, VCC must be applied before the SCL and SDA pins make contact to the main I2C bus. This is essential
when the TCA9511A is placed on the add-on card circuit board, as in 节 9.3. Although the pre-charge circuitry
exists on both the -IN and -OUT side, the example in 节 9.3 shows SCLIN and SDAIN connecting to the main
bus. The supply voltage to VCC can be applied early by ensuring that the VCC and GND pin contacts are
physically longer than the contacts for the SCLIN and SDAIN pins. If a voltage supervisor will also be used to
control the voltage supply on the add-on card, additional delay will exist before the 1 V pre-charge voltage is
present on the SCL and SDA pins.
10.2 Power-on Reset Requirements
In order to ensure that the part starts up in the correct state, it is recommended that the power supply ramp rates
meet the below requirements.
表 10-1. Recommended supply ramp rates
Parameter
Rise rate
Fall rate
MIN
MAX
1000
1000
UNIT
ms
tRT
tFT
0.1
0.1
ms
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
11 Layout
11.1 Layout Guidelines
For printed circuit board (PCB) layout of the TCA9511A, common PCB layout practices should be followed but
additional concerns related to high-speed data transfer such as matched impedances and differential pairs are
not a concern for I2C signal speeds. In all PCB layouts, it is a best practice to avoid right angles in signal traces,
to fan out signal traces away from each other upon leaving the vicinity of an integrated circuit (IC), and to use
thicker trace widths to carry higher amounts of current that commonly pass through power and ground traces.
By-pass and de-coupling capacitors are commonly used to control the voltage on the VCC pin, using a larger
capacitor to provide additional power in the event of a short power supply glitch and a smaller capacitor to filter
out high frequency ripple. These capacitors should be placed as close to the TCA9511A as possible. These best
practices are shown in 节 11.2.
The layout example provided in 节 11.2 shows a 4 layer board, which is preferable for boards with higher density
signal routing. On a 4 layer PCB, it is common to route signals on the top and bottom layer, dedicate one internal
layer to a ground plane, and dedicate the other internal layer to a power plane. In a board layout using planes or
split planes for power and ground, vias are placed directly next to the surface mount component pad which
needs to attach to VCC or GND and the via is connected electrically to the internal layer or the other side of the
board. Vias are also used when a signal trace needs to be routed to the opposite side of the board, shown in the
节 11.2 for the VCC side of the resistor connected to the EN pin; however, this routing and via is not necessary if
VCC and GND are both full planes as opposed to the partial planes depicted.
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
11.2 Layout Example
To add-on card
LEGEND
Power or GND Plane
By-pass/De-coupling
capacitors
VIA to Power Plane
VIA to GND Plane
VIA to opposite layer
EN
VCC
SDAOUT
SDAIN
1
2
3
4
8
7
6
5
SCLOUT
SCLIN
GND
READY
To backplane
(main I2C bus)
图 11-1. Layout example for TCA9511A
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TCA9511A
TCA9511A
www.ti.com.cn
ZHCSKD1C – OCTOBER 2019 – REVISED JANUARY 2021
12 Device and Documentation Support
12.1 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.2 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料,可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范,并且不一定反映 TI 的观点;请参阅
TI 的《使用条款》。
12.3 Trademarks
TI E2E™ is a trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
12.4 静电放电警告
静电放电 (ESD) 会损坏这个集成电路。德州仪器 (TI) 建议通过适当的预防措施处理所有集成电路。如果不遵守正确的处理
和安装程序,可能会损坏集成电路。
ESD 的损坏小至导致微小的性能降级,大至整个器件故障。精密的集成电路可能更容易受到损坏,这是因为非常细微的参
数更改都可能会导致器件与其发布的规格不相符。
12.5 术语表
TI 术语表
本术语表列出并解释了术语、首字母缩略词和定义。
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TCA9511A
PACKAGE OPTION ADDENDUM
www.ti.com
30-May-2023
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TCA9511ADGKR
ACTIVE
VSSOP
DGK
8
2500 RoHS & Green
NIPDAUAG | SN
Level-1-260C-UNLIM
-40 to 125
9511A
Samples
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Jun-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TCA9511ADGKR
TCA9511ADGKR
VSSOP
VSSOP
DGK
DGK
8
8
2500
2500
330.0
330.0
12.4
12.4
5.3
5.3
3.4
3.4
1.4
1.4
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
4-Jun-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TCA9511ADGKR
TCA9511ADGKR
VSSOP
VSSOP
DGK
DGK
8
8
2500
2500
364.0
366.0
364.0
364.0
27.0
50.0
Pack Materials-Page 2
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明