TCAN330DCNT [TI]
3.3V CAN 收发器 | DCN | 8 | -40 to 125;型号: | TCAN330DCNT |
厂家: | TEXAS INSTRUMENTS |
描述: | 3.3V CAN 收发器 | DCN | 8 | -40 to 125 |
文件: | 总45页 (文件大小:2163K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
TCAN33x 具备 CAN FD(灵活数据速率)的 3.3V CAN 收发器
1 特性
3 说明
1
•
3.3V 单电源运行
数据速率高达 5Mbps(TCAN33xG 器件)
TCAN33x 系列器件兼容 ISO 11898 高速 CAN(控制
器局域网)物理层标准。TCAN330、TCAN332、
TCAN334 和 TCAN337 的数据传输速率均高达
1Mbps。TCAN330G、TCAN332G、TCAN334G 和
TCAN337G 器件的 ISO 11898-2 更新版本发布正在审
理中(包括 CAN FD 和定义环路延迟对称的附加时序
参数)。这些器件具有许多保护 特性, 包括驱动器和
接收器显性超时 (DTO),用以确保 CAN 网络的稳定
性。该系列器件还集成有 12kV IEC-61000-4-2 ESD
接触放电保护,无需使用附加组件即可确保系统级的稳
定性。
•
•
•
•
符合 ISO 11898-2 标准
SOIC-8 和 SOT-23 封装选项
工作模式:
–
–
–
–
正常模式(所有器件)
具有唤醒功能的低功耗待机模式 (TCAN334)
静音模式(TCAN330、TCAN337)
关断模式(TCAN330、TCAN334)
•
•
•
•
•
±12V 的宽共模工作电压范围
±14V 的总线引脚故障保护
总环路延迟 < 135ns
器件信息(1)
宽工作环境温度范围:–40°C 至 125°C
优化了未上电时的性能:
器件型号
TCAN330/G
封装
SOIC (8)
封装尺寸(标称值)
4.90mm × 3.91mm
TCAN332/G
TCAN334/G
TCAN337/G
–
总线和逻辑引脚为高阻抗(运行总线或应用上无
负载)
SOT-23 (8)
2.90mm x 1.60mm
–
上电/断电无干扰运行
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
•
•
出色的 EMC 性能
保护 功能:
方框图
–
总线终端的 ESD 保护
VCC
3
SHDN/NC/FAULT
Note C
–
–
HBM ESD 保护超过 ±25kV
5
FAULT LOGIC
Note B
VCC
IEC61000-4-2 ESD 接触放电保护超过
VCC
VCC
±12kV
DOMINANT
TIME OUT
TXD
1
–
–
–
–
–
–
驱动器显性超时 (TXD DTO)
接收器显性超时 (RXD DTO)
故障输出引脚(仅 TCAN337)
CANH
CANL
7
6
UNDER
VOLTAGE
VCC 欠压保护
Note C
CONTROL
AND
MODE
LOGIC
热关断保护
8
总线引脚限流
Sleep Receiver
WAKE
DETECT
Note A
2 应用
MUX
Normal Receiver
•
具有灵活数据速率网络的 CAN 中的 5Mbps 运行
(TCAN33xG 器件)
DOMINANT
TIME OUT
RXD
4
2
•
•
•
•
•
高负载 CAN 网络中的 1Mbps 运行
工业自动化、控制、传感器和驱动系统
楼宇、安全和温度控制自动化
电信基站状态和控制
GND
Copyright © 2016, Texas Instruments Incorporated
A: Sleep Receiver and Wake Detect are device dependent options and are only available in TCAN334.
B: Fault Logic are only available in TCAN337.
C: Pin 5 and 8 functions are device dependent. Refer to Device Comparison Table.
CANopen、DeviceNet、NMEA2000、
ARINC825、ISO11783、CANaerospace 等 CAN
总线标准
1
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。 有关适用的官方英文版本的最新信息,请访问 www.ti.com,其内容始终优先。 TI 不保证翻译的准确
性和有效性。 在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SLLSEQ7
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
目录
10.1 Overview ............................................................... 18
10.2 Functional Block Diagram ..................................... 18
10.3 Feature Description............................................... 19
10.4 Device Functional Modes...................................... 22
11 Application and Implementation........................ 26
11.1 Application Information.......................................... 26
11.2 Typical Application ............................................... 26
11.3 System Examples ................................................. 28
12 Power Supply Recommendations ..................... 29
13 Layout................................................................... 30
13.1 Layout Guidelines ................................................. 30
13.2 Layout Example .................................................... 31
14 器件和文档支持 ..................................................... 32
14.1 相关链接................................................................ 32
14.2 支持资源................................................................ 32
14.3 商标....................................................................... 32
14.4 静电放电警告......................................................... 32
14.5 Glossary................................................................ 32
15 机械、封装和可订购信息....................................... 32
1
2
3
4
5
6
7
8
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
说明 (续).............................................................. 3
Device Options....................................................... 3
Pin Configuration and Functions......................... 4
Specifications......................................................... 5
8.1 Absolute Maximum Ratings ...................................... 5
8.2 ESD Ratings.............................................................. 5
8.3 Recommended Operating Conditions....................... 5
8.4 Thermal Information.................................................. 5
8.5 Electrical Characteristics........................................... 6
8.6 Switching Characteristics.......................................... 8
8.7 Typical Characteristics............................................ 10
8.8 Typical Characteristics, TCAN330 Receiver........... 11
8.9 Typical Characteristics, TCAN330 Driver ............... 12
Parameter Measurement Information ................ 13
9
10 Detailed Description ........................................... 18
4 修订历史记录
Changes from Revision D (April 2016) to Revision E
Page
•
•
Changed the Pin Configuration image appearance ............................................................................................................... 4
Changed the titles of Figure 21 and Figure 22..................................................................................................................... 14
Changes from Revision C (April 2016) to Revision D
Page
•
将应用 列表中的 ARNIC825 更改成了 ARINC825.................................................................................................................. 1
Changes from Revision B (April 2016) to Revision C
Page
•
Removed the Preview Note from TCAN337 and TCAN337G in the Device Options table.................................................... 3
Changes from Revision A (January 2016) to Revision B
Page
•
•
Removed the Preview Note from all device except for TCAN337 and TCAN337G in the Device Comparison table ........... 3
Changed FAULT Pin ICL MIN value From: 5 mA To: 4 mA in the Electrical Characteristics.................................................. 7
Changes from Original (December 2015) to Revision A
Page
•
•
•
将特性 中的“总环路延迟 < 150ns”更改成了“总环路延迟 < 135ns” ......................................................................................... 1
Changed VIT(SLEEP) To: VIT(STB) and added Test conditions in the Electrical Characteristics ................................................. 7
Added –12 V < VCM < 12 V to tWK_FILTER in the Test Conditions of Switching Characteristics ............................................... 8
2
版权 © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
5 说明 (续)
该系列收发器采用 3.3V 单电源供电,因此可以直接连接 3.3V CAN 控制器/微控制器 (MCU)。此外,这些器件完全
兼容同一总线上的其他 5V CAN 收发器。
由于显性共模和隐性共模相匹配,这些器件具有卓越的 EMC 性能。这些器件具有超低功耗的关断模式和待机模
式,对于电池供电型应用而言极具 吸引力中的数字输入 D 类音频放大器。
该系列器件提供便于插接的标准 8 引脚 SOIC 封装以及面向空间受限类应用的小型 SOT-23 封装提供了出色的功能
性与安全性。
6 Device Options
DEVICE
TCAN330
TCAN332
TCAN334
TCAN337
TCAN330G
TCAN332G
TCAN334G
TCAN337G
PIN 5
SHDN
NC
PIN 8
S
DERATE
1 Mbps
1 Mbps
1 Mbps
1 Mbps
5 Mbps
5 Mbps
5 Mbps
5 Mbps
DESCRIPTION
Shutdown and silent modes
NC
STB
S
Normal mode only
SHDN
FAULT
SHDN
NC
Shutdown and standby with wake
Fault output and silent mode
Shutdown and silent modes
Normal mode only
S
NC
STB
S
SHDN
FAULT
Shutdown and standby with wake
Fault output and silent mode
Copyright © 2015–2019, Texas Instruments Incorporated
3
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
7 Pin Configuration and Functions
TCAN330 D, DCN Packages
8-Pin SOIC, SOT-23
Top View
TCAN334 D, DCN Packages
8-Pin SOIC, SOT-23
Top View
TXD
GND
VCC
1
2
3
4
8
7
6
5
S
TXD
GND
VCC
1
2
3
4
8
7
6
5
STB
CANH
CANL
SHDN
CANH
CANL
SHDN
RXD
RXD
Not to scale
Not to scale
TCAN332 D, DCN Packages
8-Pin SOIC, SOT-23
Top View
TCAN337 D, DCN Packages
8-Pin SOIC, SOT-23
Top View
TXD
GND
VCC
1
2
3
4
8
7
6
5
NC
TXD
GND
VCC
1
2
3
4
8
7
6
5
S
CANH
CANL
NC
CANH
CANL
FAULT
RXD
RXD
Not to scale
Not to scale
Pin Functions
PIN
I/O
DESCRIPTION
NAME
TCAN330 TCAN332 TCAN334 TCAN337
CAN transmit data input (LOW for dominant and HIGH for recessive bus states),
integrated pull up
TXD
1
1
1
1
I
GND
VCC
2
3
2
3
2
3
2
3
GND
Ground connection
3.3-V supply voltage
Supply
CAN receive data output (LOW for dominant and HIGH for recessive bus
states), tri-state
RXD
4
4
4
4
O
SHDN
NC
5
—
—
6
—
5
5
—
—
6
—
—
5
I
Drive high for shutdown mode. Internal pull-down.
No Connect – Not internally connected
Open drain fault output pin.
NC
O
FAULT
CANL
CANH
S
—
6
6
I/O
I/O
I
Low level CAN bus line
7
7
7
7
High level CAN bus line
8
—
8
—
—
8
8
Drive high for silent mode, integrated pull down
No Connect – Not internally connected
Drive high for low power standby mode, integrated pull down
NC
—
—
—
—
NC
I
STB
—
4
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
8 Specifications
8.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)
MIN
–0.3
–14
MAX
5
UNIT
V
Supply Voltage range, VCC
Voltage at any bus terminal (CANH or CANL), V(BUS)
Logic input terminal voltage range V(Logic_Input)
Logic output terminal voltage range, V(Logic_Output)
Logic output current, IO(LOGIC)
14
5
V
–0.3
–0.3
V
5
V
8
mA
°C
°C
Operating junction temperature range, TJ
Storage temperature, Tstg
–40
150
150
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential I/O bus voltages, are with respect to ground terminal.
8.2 ESD Ratings
VALUE
±4000
UNIT
All pins except CANH and
CANL
Human-body model (HBM), per
ANSI/ESDA/JEDEC JS-001(1)
Pins CANH and CANL
All pins
±25000
±1500
V(ESD)
Electrostatic discharge
V
Charged-device model (CDM), per JEDEC
specification JESD22-C101(2)
CANH and CANL terminals to
GND
IEC 61400-4-2 Contact Discharge
±12000
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. .
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
8.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
3
NOM
MAX
UNIT
VCC
Supply voltage
3.6
V
IOH(LOGIC)
IOL(LOGIC)
TA
Logic terminal HIGH level output current
Logic terminal LOW level output current
Operational free-air temperature
–2
mA
°C
2
–40
125
8.4 Thermal Information
TCAN33x
TCAN33x
THERMAL METRIC(1)
D (SOIC)
8 PINS
114.4
58.7
DCN (SOT-23)
8 PINS
154.4
76.6
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
Junction-to-board thermal resistance
55.2
49.2
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
11.7
11.9
ψJB
54.6
49.2
RθJC(bot)
N/A
N/A
VCC = 3.3 V, TJ = 27°C, RL = 60 Ω, SHDN, S and
PD
Average power dissipation
STB at 0 V, Input to TXD at 500 kHz, 50% duty cycle
square wave, CL(RXD) = 15 pF
65
65
mW
TSD
Thermal shutdown temperature
Thermal shutdown hysteresis
175
5
175
5
°C
°C
THYS
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2015–2019, Texas Instruments Incorporated
5
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
8.5 Electrical Characteristics
over operating free-air temperature range, TJ = –40°C to 150°C. All typical values are at 25°C and supply voltages of VCC
=
3.3 V, RL = 60 Ω, (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Supply
See Figure 18. TXD = 0 V, RL = 60 Ω,
CL = open, S, STB and SHDN = 0 V.
Typical Bus Load.
55
60
Dominant
See Figure 18. TXD = 0 V, RL = 50 Ω,
CL = open, S, STB and SHDN = 0 V.
High Bus Load.
Supply current Normal Mode
See Figure 18. TXD = 0 V, S, STB and
SHDN = 0 V, CANH = -12 V, RL = open,
CL = open
mA
Dominant with
bus fault
180
See Figure 18. TXD = VCC, RL = 50 Ω,
CL = open, S, STB and SHDN = 0 V
Recessive
3.5
2.5
ICC
See Figure 18. TXD = VCC, RL = 50 Ω,
CL = open, S = VCC
Supply Current: Silent Mode
Supply Current: Standby Mode
TA < 85°C, STB at VCC, RXD floating,
TXD at VCC
15
20
1
STB at VCC, RXD floating, TXD at VCC
µA
TA < 85°C, SHDN at VCC, RXD floating,
TXD at VCC
Supply Current: Shutdown Mode
SHDN = VCC, RXD floating, TXD at VCC
2.5
2.6
Rising under voltage detection on VCC for protected
mode
2.2
UV(VCC)
V
Falling under voltage detection on VCC for protected
mode
1.65
2
2.5
VHYS(UVVCC)
Hysteresis voltage on UV(VCC)
200
mV
Driver
CANH
See Figure 31 and Figure 19, TXD = 0
V, S, STB and SHDN = 0 V, RL = 60 Ω,
CL = open
2.45
0.5
VCC
VO(D)
Bus output voltage (dominant)
V
V
CANL
1.25
See Figure 31 and Figure 19, TXD =
VCC, STB, SHDN = 0 V, S = 0 V or VCC
(1), RL = open (no load)
VO(R)
Bus output voltage (recessive)
1.85
See Figure 31 and Figure 19, TXD = 0
V, S, STB and SHDN = 0 V, 50 Ω ≤ RL
65 Ω, CL = open
≤
1.6
1.5
3
3
VOD(D)
Differential output voltage (dominant)
V
See Figure 31 and Figure 19, TXD = 0
V, S, STB and SHDN = 0 V, 45 Ω ≤ RL
50 Ω, CL = open
<
See Figure 31 and Figure 19, TXD =
VCC, S, STB and SHDN = 0 V, RL = 60
Ω, CL = open
–120
–50
12
50
TA < 85°C, See Figure 31 and Figure 19,
TXD = VCC, S, STB and SHDN = 0 V, RL
= open (no load), CL = open
VOD(R)
Differential output voltage (recessive)
mV
See Figure 31 and Figure 19, TXD =
VCC, S, STB and SHDN = 0 V, RL
open (no load), CL = open
=
–50
100
400
Output symmetry (dominant and recessive)
(CANHREC + CANLREC – CANHDOM – CANLDOM
See Figure 31 and Figure 19, S, STB
and SHDN = 0 V, RL = 60 Ω, CL = open
V(SYM)
–400
–200
mV
mA
mA
)
See Figure 26, V(CANH) = –12 V, CANL =
open, TXD = 0 V
IOS(DOM)
Short-circuit steady-state output current, Dominant
Short-circuit steady-state output current, Recessive
See Figure 26, V(CANL) = 12 V, CANH =
open, TXD = 0 V
200
5
See Figure 26, –12 V ≤ VBUS ≤ 12 V,
VBUS = CANH = CANL, TXD = VCC
IOS(REC)
–5
(1) The bus output voltage (recessive) will be the same if the device is in normal mode with S terminal LOW or if the device is in silent
mode with the S terminal is HIGH.
6
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
Electrical Characteristics (continued)
over operating free-air temperature range, TJ = –40°C to 150°C. All typical values are at 25°C and supply voltages of VCC
=
3.3 V, RL = 60 Ω, (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Receiver
Input threshold voltage, normal modes and selective
wake modes
VIT
500
900
mV
Hysteresis voltage for input threshold, normal
modes and selective wake modes
See Figure 20 and Table 7
VHYS
VCM
120
Common Mode Range: normal and silent modes
–12
400
12
V
–2 V < VCM < 7 V
See Figure 20 and Table 7
1150
mV
VIT(STB)
Input Threshold, standby mode
–12 V < VCM < 12 V
See Figure 20 and Table 7
400
1350
6
mV
µA
TA < 85°C, CANH = CANL = 3.3 V, VCC
to GND via 0-Ω and 47-kΩ resistor
IIOFF(LKG)
Power-off (unpowered) bus input leakage current
CANH = CANL = 3.3 V, VCC to GND via
0-Ω and 47-kΩ resistor
12
CI
Input capacitance to ground (CANH or CANL)
Differential input capacitance
20
10
80
40
pF
CID
RID
RIN
Differential input resistance
TXD = VCC, Normal Mode
TXD = VCC, Normal mode
30
15
kΩ
Input resistance (CANH or CANL)
Input resistance matching: [1 – (RIN(CANH) /
RIN(CANL))] × 100 %
RIN(M)
V(CANH) = V(CANL)
–3%
3%
TXD Terminal (CAN Transmit Data Input)
VIH
HIGH level input voltage
LOW level input voltage
2
V
VIL
0.8
3
V
IIH
HIGH level input leakage current
LOW level input leakage current
Unpowered leakage current
Input Capacitance
TXD = VCC = 3.6 V
–2.5
–4
0
0
µA
µA
µA
pF
IIL
TXD = 0 V, VCC = 3.6 V
TXD = 3.6 V, VCC = 0 V
0
ILKG(OFF)
I(CAP)
–2
0
2.5
2.5
RXD Terminal (CAN Receive Data Output)
VOH
HIGH level output voltage
LOW level output voltage
Unpowered leakage current
See Figure 20, IO = –2 mA
See Figure 20, IO = 2 mA
RXD = 3.6 V, VCC = 0 V
0.8 x VCC
V
V
VOL
0.2
0
0.4
1
ILKG(OFF)
–1
2
µA
STB/S/SHDN Terminals
VIH
HIGH level input voltage
V
VIL
LOW level input voltage
0.8
10
1
V
IIH
HIGH level input leakage current
LOW level input leakage current
Unpowered leakage current
STB, S, SHDN = VCC = 3.6 V
–3
–4
–3
0
0
0
µA
µA
µA
IIL
STB, S, SHDN = 0 V, VCC = 3.6 V
STB, S, SHDN = 3.6 V, VCC = 0 V
ILKG(OFF)
5
FAULT Pin (Fault Output), TCAN337 only
ICH
ICL
Output current high level
Output current low level
FAULT = VCC, See Figure 28
FAULT = 0.4 V, See Figure 28
–10
4
µA
12
mA
Copyright © 2015–2019, Texas Instruments Incorporated
7
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
8.6 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Device Switching Characteristics
Total loop delay, driver input (TXD) to
receiver output (RXD), recessive to
dominant and dominant to recessive
See Figure 23, S, STB and SHDN = 0 V,
RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF
tPROP(LOOP)
100
120
135
180
ns
ns
See Figure 23, S, STB and SHDN = 0 V,
RL = 120 Ω, CL = 200 pF,
CL(RXD) = 15 pF
Total Loop delay in highly loaded
network
tPROP(LOOP)
tBUS_SYM_2
tREC_SYM_2
2 Mbps transmitted recessive bit width
2 Mbps received recessive bit width
2 Mbps receiver timing symmetry
435
400
530
550
ns
ns
See Figure 24, S or STB = 0 V, RL = 60
Ω, CL = 100 pF, CL(RXD) = 15 pF,
tBIT = 500 ns
TCAN330G, TCAN332G, TCAN334G
and TCAN337G only
ΔtSYM_2
–65
40
ns
(tREC_SYM_2 - tBUS_SYM_2
)
tBUS_SYM_5
tREC_SYM_5
5 Mbps transmitted recessive bit width
5 Mbps received recessive bit width
5 Mbps receiver timing symmetry
155
120
210
220
ns
ns
See Figure 24, S or STB = 0 V, RL = 60
Ω, CL = 100 pF, CL(RXD) = 15 pF,
tBIT = 200 ns
TCAN330G, TCAN332G, TCAN334G
and TCAN337G only
ΔtSYM_5
–45
15
10
ns
µs
(tREC_SYM_5 - tBUS_SYM_5
)
See Figure 21 and Figure 22.
RL = 60 Ω, CL = 100 pF,
CL(RXD) = 15 pF
tMODE
Mode change time
5
Time for device to return to normal
operation from UV(VCC) under voltage
event
tUV_RE-ENABLE
Re-enable time after UV event
1000
4
µs
µs
Bus time to meet Filtered Bus
Requirements for Wake Up Request
See Figure 33, Standby mode.
–12 V < VCM < 12 V
tWK_FILTER
0.5
Driver Switching Characteristics
Propagation delay time, HIGH TXD to
Driver Recessive
tpHR
tpLD
25
20
Propagation delay time, LOW TXD to
Driver Dominant
See Figure 19, S, STB and SHDN = 0 V.
ns
RL = 60 Ω, CL = 100 pF,
tsk(p)
Pulse skew (|tpHR - tpLD|)
5
17
9
tr
tf
Differential output signal rise time
Differential output signal fall time
See Figure 25,
RL = 60 Ω, CL = 100 pF
(1)
tTXD_DTO
Driver dominant time out
1.2
2.6
3.8
ms
Receiver Switching Characteristics
Propagation delay time, bus recessive
tpRH
62
56
input to high RXD output
Propagation delay time, bus dominant
input to RXD low output
See Figure 20, CL(RXD) = 15 pF CANL =
1.5 V, CANH = 3.5 V
tpDL
ns
tr
Output signal rise time (RXD)
Output signal fall time (RXD)
7
6
3
tf
(2)
tRXD_DTO
Receiver dominant time out
See Figure 27, CL(RXD) = 15 pF
1.6
5
ms
(1) The TXD dominant time out (tTXD_DTO) disables the driver of the transceiver once the TXD has been dominant longer than tTXD_DTO,
which releases the bus lines to recessive, preventing a local failure from locking the bus dominant. The driver may only transmit
dominant again after TXD has been returned HIGH (recessive). While this protects the bus from local faults, locking the bus dominant, it
limits the minimum data rate possible. The CAN protocol allows a maximum of eleven successive dominant bits (on TXD) for the worst
case, where five successive dominant bits are followed immediately by an error frame. This, along with the tTXD_DTO minimum, limits the
minimum bit rate. The minimum bit rate may be calculated by: Minimum Bit Rate = 11/ tTXD_DTO = 11 bits / 1.2 ms = 9.2 kbps.
(2) The RXD timeout (tRXD_DTO) disables the RXD output in the case that the bus has been dominant longer than tRXD_DTO, which releases
RXD pin to the recessive state (high), thus preventing a dominant bus failure from permanently keeping the RXD pin low. The RXD pin
will automatically resume normal operation once the bus has been returned to a recessive state. While this protects the protocol
controller from a permanent dominant state, it limits the minimum data rate possible. The CAN protocol allows a maximum of eleven
successive dominant bits (on RXD) for the worst case, where five successive dominant bits are followed immediately by an error frame.
This, along with the tRXD_DTO minimum, limits the minimum bit rate. The minimum bit rate may be calculated by: Minimum Bit Rate = 11 /
tRXD_DTO = 11 bits / 1.6 ms = 6.9 kbps.
8
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
TXD fault stuck dominant, example PCB
failure or bad software
Fault is repaired & transmission
capability restored
tTXD_DTO
TXD (driver)
Driver disabled freeing bus for other nodes
Bus would be —stuck dominant“ blocking communication for the
whole network but TXD DTO prevents this and frees the bus for
Normal CAN
communication
communication after the time tTXD_DTO
.
CAN
Bus
Signal
tTXD_DTO
Communication from
other bus node(s)
Communication from
repaired node
FAULT is signaled to link layer / protocol.
Fault indication is removed.
TXDDTO
Flag
RXD
(receiver)
Communication from
other bus node(s)
Communication from
repaired local node
Communication from
local node
Figure 1. Example Timing Diagram for TXD DTO and FAULT Pin
Fault is repaired and normal
communication returns
Normal CAN
communication
Bus Fault stuck dominant, example CANH
short to supply and CAN L short to GND.
CAN Bus
Signal
RXD mirrors
bus
RXD
(reciever)
tRXD_DTO
RXD output is returned recessive (high) and
FAULT is signaled to link layer / protocol.
FAULT cleared
signal is given
RXDDTO
FLAG
Figure 2. Example Timing Diagram for RXD DTO and FAULT Pin
Copyright © 2015–2019, Texas Instruments Incorporated
9
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
8.7 Typical Characteristics
21
20.8
20.6
20.4
20.2
20
0.16
0.14
0.12
0.1
RL = Open
RL = 60 W
0.08
0.06
0.04
0.02
0
19.8
19.6
19.4
0
200
400 600
Frequency (kbps)
800
1000
0
1
2
3
VO(CANL) - Low-Level Output Voltage (V)
4
D001
D002
VCC = 3.3 V
Normal Mode
Temp = 25°C
VO = 0.5 to 3.3 V
VCC = 3.3 V
Normal Mode
Temp = 25°C
60 Ω Load
Figure 3. Supply Current (RSM) vs Frequency
Figure 4. Driver Low-Level Output Current vs Low-level
Output Voltage
160
140
120
100
80
3.0
RL = Open
RL = 60 W
2.5
2.0
1.5
1.0
0.5
0.0
60
40
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
20
0
0
1
2
3
VO(CANH) - High-Level Output Voltage (V)
4
-40 -25 -10
5
20 35 50 65 80 95 110 125
Free-Air Temperature (èC)
D003
D004
VO = 0.5 to 3.3 V
VCC = 3.3 V
Normal Mode
Temp = 25°C
VO = 0.5 to 3.3 V
VCC = 3.3 V
Normal Mode
Temp = 25°C
60 Ω Load
Figure 5. Driver High-Level Output Current vs High-level
Output Voltage
Figure 6. Dominant Voltage (VOD) vs Free-Air Temperature
10
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
8.8 Typical Characteristics, TCAN330 Receiver
68
67
66
65
64
63
62
61
61
60
59
58
57
56
55
60
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
54
53
59
58
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Free-Air Temperature (èC)
Free-Air Temperature (èC)
D005
D006
Figure 7. Receiver Bus Recessive Input to High RXD Output
Propagation Delay Time vs Free-Air Temperature
Figure 8. Receiver Bus Dominant Input to Low RXD Output
Propagation Delay Time vs Free-Air Temperature
9
8
7
6
5
4
3
6.6
6.5
6.4
6.3
6.2
6.1
6
5.9
5.8
2
5.7
5.6
5.5
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
1
0
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Free-Air Temperature (èC)
Free-Air Temperature (èC)
D007
D008
Figure 9. Receiver Rise Time vs Free-Air Temperature
Figure 10. Receiver Fall Time vs Free-Air Temperature
Copyright © 2015–2019, Texas Instruments Incorporated
11
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
8.9 Typical Characteristics, TCAN330 Driver
35
30
25
20
15
35
30
25
20
15
10
5
10
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
5
0
-40
0
-40
-20
0
20
40
60
80
100 120 140
-20
0
20
40
60
80
100 120 140
Free-Air Temperature (èC)
Free-Air Temperature (èC)
D009
D010
Figure 11. Driver High TXD Input to Driver Recessive Output
Propagation Delay Time vs Free-Air Temperature
Figure 12. Driver Low TXD Input to Driver Dominant Output
Propagation Delay Time vs Free-Air Temperature
35
30
25
20
15
16
14
12
10
8
6
10
4
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
5
2
0
0
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Free-Air Temperature (èC)
Free-Air Temperature (èC)
D011
D012
Figure 13. Differential Output Signal Rise Time vs Free-Air
Temperature
Figure 14. Differential Output Signal Fall Time vs Free-Air
Temperature
100
90
80
70
60
50
40
30
9
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
8
7
6
5
4
3
2
1
0
20
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
10
0
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Free-Air Temperature (èC)
Free-Air Temperature (èC)
D013
D014
Figure 15. Pulse Skew (|tpHR - tpLD|) vs Free-Air Temperature
Figure 16. Total Loop Delay Recessive to Dominant
tPROP(LOOP1) vs Free-Air Temperature
12
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
Typical Characteristics, TCAN330 Driver (continued)
98
96
94
92
90
88
86
84
82
80
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
-40
-20
0
20
40
60
80
100 120 140
Free-Air Temperature (èC)
D015
Figure 17. Total Loop Delay Dominant to Recessive tPROP(LOOP2) vs Free-Air Temperature
9 Parameter Measurement Information
CANH
RL
TXD
CL
CANL
Figure 18. Supply Test Circuit
CANH
RL
VCC
0V
50%
tpLD
50%
tpHR
TXD
TXD
CL
VOD
VO(CANH)
90%
10%
CANL
0.9V
VO(CANL)
VOD
0.5V
tR
tF
Figure 19. Driver Test Circuit and Measurement
Copyright © 2015–2019, Texas Instruments Incorporated
13
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
Parameter Measurement Information (continued)
CANH
1.5 V
0.9 V
+
VID
IO
RXD
0.5 V
0 V
VOH
VID
+
tpDL
90%
œ
tpRH
VO
CL_RXD
CANL
VO(RXD)
50%
10%
œ
VOL
tF
tR
Figure 20. Receiver Test Circuit and Measurement
CANH
VIH
VIH
TXD
0 V
RL
CL
S
SHDN/S/STB
50%
50%
CANL
SHDN/S/STB
0V
0 V
VI
tMODE
tMODE
RXD
+
VOH
VO
CL_RXD
CANH - CANL
RXD
50%
œ
500mV
VOL
Figure 21. tMODE Test Circuit and Measurement, from Normal to Shutdown, Standby or Silent Mode
VIH
VIH
TXD
TXD
CANH
TXD
VI
RL
CL
0 V
VIH
0 V
VIH
200 ns
200 ns
CANL
SHDN/S/STB
VI
50%
S
SHDN/S/STB
50%
RXD
0 V
0 V
+
tMODE
tMODE
VO
CL_RXD
VOH
VOH
œ
RXD
900 mV
50%
CANH - CANL
VOL
Figure 22. tMODE Test Circuit and Measurement, from Shutdown, Standby or Silent to Normal Mode
14
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
Parameter Measurement Information (continued)
CANH
VCC
TXD
CL
VI
RL
50%
TXD
CANL
0 V
tPROP(LOOP2)
tPROP(LOOP1)
RXD
+
VOH
VO
CL_RXD
50%
RXD
œ
VOL
Figure 23. tPROP(LOOP) Test Circuit and Measurement
VI
70%
TXD
30%
30%
CANH
0V
5 x tBIT
tBIT
TXD
VI
RL
CANL
900mV
CANH - CANL
500mV
RXD
tBUS_SYM
VO
CL_RXD
VOH
70%
RXD
30%
VOL
tREC_SYM
Figure 24. Loop Delay Symmetry Test Circuit and Measurement
Copyright © 2015–2019, Texas Instruments Incorporated
15
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
Parameter Measurement Information (continued)
CANH
VIH
TXD
TXD
0 V
RL
CL
VOD
VOD(D)
CANL
0.9 V
VOD
0.5 V
0 V
tTXD_DTO
Figure 25. TXD Dominant Time Out Test Circuit and Measurement
200 ꢀs
IOS
CANH
TXD
VBUS
IOS
CANL
VBUS
VBUS
or
0 V
0 V
VBUS
VBUS
Figure 26. Driver Short-Circuit Current Test and Measurement
VID(D)
CANH
+
0.9 V
VID
0.5 V
0 V
RXD
VID
+
œ
CL_RXD
VO
CANL
VOH
0 V
RXD
50%
œ
tRXD_DTO
Figure 27. RXD Dominant Timeout Test Circuit and Measurement
16
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
Parameter Measurement Information (continued)
IFAULT
TXD
DTO
FAULT
RXD
DTO
+
œ
Thermal
Shutdown
UV
Lockout
GND
Figure 28. FAULT Test and Measurement
Copyright © 2015–2019, Texas Instruments Incorporated
17
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
10 Detailed Description
10.1 Overview
This family of CAN transceivers is compatible with the ISO11898-2 High-Speed CAN (controller area network)
physical layer standard. They are designed to interface between the differential bus lines in CAN and the CAN
protocol controller.
10.2 Functional Block Diagram
SHDN / NC / FAULT
VCC
Note C
5
3
FAULT LOGIC
Note B
VCC
VCC
VCC
DOMINANT
TIME OUT
TXD
S / NC / STB
RXD
1
7
CANH
CANL
Under
Voltage
6
Note C
8
CONTROL and
MODE
LOGIC
Sleep Receiver
Note A
WAKE
DETECT
MUX
Normal Receiver
4
DOMINANT
TIME OUT
2
GND
Copyright © 2016, Texas Instruments Incorporated
A. Sleep Receiver and Wake Detect are device dependent options and are only available in TCAND334.
B. Fault Logic is only available in TCAND337.
C. Pin 5 and 8 functions are device dependent. Refer to Device Options.
18
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
10.3 Feature Description
10.3.1 TXD Dominant Timeout (TXD DTO)
During normal mode (the only mode where the CAN driver is active), the TXD DTO circuit prevents the
transceiver from blocking network communication in the event of a hardware or software failure where TXD is
held dominant longer than the timeout period tTXD_DTO. The DTO circuit timer starts on a falling edge on TXD.
The DTO circuit disables the CAN bus driver if no rising edge is seen before the timeout period expires. This
frees the bus for communication between other nodes on the network. The CAN driver is re-activated when a
recessive signal is seen on TXD pin, thus clearing the TXD DTO condition. The receiver and RXD pin still reflect
the CAN bus, and the bus pins are biased to recessive level during a TXD dominant timeout.
10.3.2 RXD Dominant Timeout (RXD DTO)
All devices have a RXD DTO circuit that prevents a bus stuck dominant fault from permanently driving the RXD
output dominant (low) when the bus is held dominant longer than the timeout period tRXD_DTO. The RXD DTO
timer starts on a falling edge on RXD (bus going dominant). If no rising edge (bus returning recessive) is seen
before the timeout constant of the circuit expires (tRXD_DTO), the RXD pin returns high (recessive). The RXD
output is re-activated to mirror the bus receiver output when a recessive signal is seen on the bus, clearing the
RXD dominant timeout. The CAN bus pins are biased to the recessive level during a RXD DTO.
10.3.3 Thermal Shutdown
If the junction temperature of the device exceeds the thermal shutdown threshold, the device turns off the CAN
driver circuits thus blocking the TXD-to-bus transmission path. The shutdown condition is cleared when the
junction temperature of the device drops below the thermal shutdown temperature of the device. If the fault
condition that caused the thermal shutdown is still present, the temperature may rise again and the device will
enter thermal shut down again. Prolonged operation with thermal shutdown conditions may affect device
reliability. The thermal shutdown circuit includes hysteresis to avoid oscillation of the driver output.
During thermal shutdown the CAN bus drivers are turned off, thus no transmission is possible from TXD to the
bus. The CAN bus pins are biased to recessive level during a thermal shutdown and the receiver to RXD path
remains operational.
10.3.4 Undervoltage Lockout and Unpowered Device
The VCC supply terminal has under voltage detection which will place the device in protected mode if the supply
drops below the UVLO threshold. This protects the bus during an under voltage event on VCC by placing the bus
into a high impedance biased to ground state and the RXD terminal into a tri-stated (high impedance) state.
During undervoltage the device does not pass any signals from the bus. If the device is in normal mode and VCC
supply is lost the device will transition to a protected mode.
The device is designed to be an "ideal passive" or “no load” to the CAN bus if the device is unpowered. The bus
terminals (CANH, CANL) have low leakage currents when the device is unpowered, so the device does not load
the bus. This is critical if some nodes of the network are unpowered while the rest of the of network remains
operational. Logic pins also have low leakage currents when the device is unpowered, so the device does not
load other circuits which may remain powered.
Table 1. Undervoltage Protection 3.3-V Single Supply Devices
VCC
GOOD
DEVICE STATE
Operational
Protected
BUS
RXD
Per Operating Mode
Per Operating Mode
High Impedance
High Impedance
BAD
Common mode bias to GND
High Impedance (no load)
UNPOWERED
Unpowered
Copyright © 2015–2019, Texas Instruments Incorporated
19
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
10.3.5 Fault Pin (TCAN337)
If one or more of the faults (TXD-Dominant Timeout, RXD dominant Timeout, Thermal Shutdown or
Undervoltage Lockout) occurs, the FAULT pin (open-drain) turns off, resulting in a high level when externally
pulled up to VCC supply.
VCC
ꢀP
FAULT
Input
TXD
DTO
FAULT
RXD
DTO
Thermal
Shutdown
UV
Lockout
GND
Figure 29. FAULT Pin Function Diagram and Application
10.3.6 Floating Pins
The device has internal pull ups and pull downs on critical terminals to place the device into known states if the
pin floats. See Table 1 for details on pin bias conditions.
Table 2. Pin Bias
PIN
PULL UP or PULL DOWN
COMMENT
Weakly biases TXD toward recessive to prevent bus blockage or TXD DTO
triggering.
TXD
Pull up
STB
S
Pull down
Pull down
Pull down
Weakly biases STB terminal towards normal mode.
Weakly biases S terminal towards normal mode.
Weakly biases SHDN terminal towards normal mode.
SHDN
The internal bias should not be relied on by design, especially in noisy environments, but should be considered a
fall back protection. Special care needs to be taken when the device is used with MCUs using open drain
outputs. TXD is weakly internally pulled up. The TXD pull up strength and CAN bit timing require special
consideration when this device is used with an open drain TXD output on the microprocessor's CAN controller.
An adequate external pull up resistor must be used to ensure that the TXD output of the microprocessor
maintains adequate bit timing input to the CAN transceiver.
10.3.7 CAN Bus Short Circuit Current Limiting
The device has several protection features that limit the short circuit current when a CAN bus line is shorted.
These include CAN driver current limiting (dominant and recessive). The device has TXD dominant time out
which prevents permanently having the higher short circuit current of dominant state in case of a system fault.
During CAN communication the bus switches between dominant and recessive states, thus the short circuit
current may be viewed either as the current during each bus state or as a DC average current. For system
current and power considerations in the termination resistors and common mode choke ratings the average short
circuit current should be used. The percentage dominant is limited by the TXD dominant time out and CAN
protocol which has forced state changes and recessive bits such as bit stuffing, control fields, and interframe
space. These ensure there is a minimum recessive amount of time on the bus even if the data field contains a
high percentage of dominant bits.
20
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
The short circuit current of the bus depends on the ratio of recessive to dominant bits and their respective short
circuit currents. The average short circuit current may be calculated with the following formula:
IOS(AVG) = %Transmit x [(%REC_Bits x IOS(SS)_REC ) + (%DOM_Bits x IOS(SS)_DOM)] + [%Receive x IOS(SS)_REC
]
(1)
Where:
•
•
•
•
•
•
•
IOS(AVG) is the average short circuit current
%Transmit is the percentage the node is transmitting CAN messages
%Receive is the percentage the node is receiving CAN messages
%REC_Bits is the percentage of recessive bits in the transmitted CAN messages
%DOM_Bits is the percentage of dominant bits in the transmitted CAN messages
IOS(SS)_REC is the recessive steady state short circuit current
IOS(SS)_DOM is the dominant steady state short circuit current
The short circuit current and possible fault cases of the network should be taken into consideration when sizing
the power ratings of the termination resistance and other network components.
10.3.8 ESD Protection
The bus pins of the TCAN33x family possess on-chip ESD protection against ±25-kV human body model (HBM)
and ±12-kV IEC61000-4-2 contact discharge. The IEC-ESD test is far more severe than the HBM-ESD test. The
50% higher charge capacitance, CS, and 78% lower discharge resistance, RD of the IEC model produce
significantly higher discharge currents than the HBM-model.
As stated in the IEC 61000-4-2 standard, contact discharge is the preferred test method; although IEC air-gap
testing is less repeatable than contact testing, air discharge protection levels are inferred from the contact
discharge test results.
R
R
D
C
40
35
30
25
20
15
10
5
50M
(1M)
330Ω
(1.5k)
10kV IEC
High-Voltage
Pulse
Generator
Device
Under
Test
150pF
(100pF)
C
S
10kV HBM
0
0
50
100
150
200
250
300
Time - ns
Figure 30. HBM and IEC-ESD Models and Currents in Comparison (HBM Values in Parenthesis)
10.3.9 Digital Inputs and Outputs
All the devices in this family are single 3.3-V nominal supply devices. The digital logic input and output levels for
these devices have TTL threshold levels.
Copyright © 2015–2019, Texas Instruments Incorporated
21
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
10.4 Device Functional Modes
10.4.1 CAN Bus States
www.ti.com.cn
The CAN bus has two logical states during operation: recessive and dominant. See Figure 31 and Figure 32.
Recessive bus state is when the high resistive internal input resistors of each node's receiver bias the bus to a
common mode of about 1.85 V across the bus termination resistors. Recessive is equivalent to logic high and is
typically a differential voltage on the bus of about 0 V. Recessive state is also the idle state.
Dominant bus state is when the bus is driven differentially by one or more drivers. Current is induced to flow
through the termination resistors and generate a differential voltage on the bus. Dominant is equivalent to logic
low and is a differential voltage on the bus greater than the minimum threshold for a CAN dominant. A dominant
state overwrites the recessive state.
During arbitration, multiple CAN nodes may transmit a dominant bit at the same time. In this case the differential
voltage of the bus will be greater than the differential voltage of a single driver.
The host microprocessor of the CAN node will use the TXD terminal to drive the bus and will receive data from
the bus on the RXD pin.
Transceivers with low power Standby Mode have a third bus state where the bus terminals are weakly biased to
ground via the high resistance internal resistors of the receiver. See Figure 31 and Figure 32.
Standby and Shutdown
Modes
Normal and Silent Modes
CANH
CANH
Vdiff
1.85 V
A
B
RXD
Bias
Unit
Vdiff
CANL
CANL
A. Normal and Silent Modes
Recessive
Dominant
Recessive
Time, t
B. Standby and Shutdown Modes
Figure 31. Bus States (Physical Bit
Representation)
Figure 32. Simplified Recessive Common Mode
Bias Unit and Receiver
The devices have four main operating modes:
1. Normal mode (all devices)
2. Silent mode (TCAN330, TCAN337)
3. Standby mode with wake (TCAN334)
4. Shutdown mode (TCAN330, TCAN334)
Table 3. CAN Transceivers with Silent Mode
S
Device MODE
DRIVER
RECEIVER
RXD PIN
Reduced Power Silent
(Listen) Mode
HIGH
Disabled (OFF)(1)
Enabled (ON)
Enabled (ON)
Enabled (ON)
Mirrors Bus State(2)
LOW/NC
Normal Mode
(1) See Figure 31 for bus state.
(2) Mirrors bus state: low if CAN bus is dominant, high if CAN bus is recessive.
22
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
Table 4. CAN Transceivers with Standby Mode with Wake
STB
Device MODE
DRIVER
RECEIVER
RXD Terminal
High (Recessive) until
Ultra Low Current Standby
Mode
Low Power Receiver and
Bus Monitor Enabled (ON)
HIGH
Disabled (OFF)(1)
Enabled (ON)
WUP, then filtered mirrors
(2)
of Bus State
(3)
LOW/NC
Normal Mode
Enabled (ON)
Mirrors Bus State
(1) See Figure 31 for bus state.
(2) Standby Mode RXD behavior: See Figure 33.
(3) Mirrors bus state: low if CAN bus is dominant, high if CAN bus is recessive.
Table 5. CAN Transceivers with Shutdown Mode
SHDN
HIGH
Device MODE
Lowest Current
Normal Mode
DRIVER
Disabled (OFF)(1)
RECEIVER
Disabled (OFF)
Enabled (ON)
RXD Terminal
High (Recessive)
(2)
LOW/NC
Enabled (ON)
Mirrors Bus State
(1) See Figure 31 for bus state.
(2) Mirrors bus state: low if CAN bus is dominant, high if CAN bus is recessive.
10.4.2 Normal Mode
This is the normal operating mode of the device. The CAN driver and receiver are fully operational and CAN
communication is bi-directional. The driver is translating a digital input on TXD to a differential output on CANH
and CANL. The receiver is translating the differential signal from CANH and CANL to a digital output on RXD.
10.4.3 Silent Mode
This is the silent or receive only mode of the device. The CAN driver is disabled but the receiver is fully
operational. CAN communication is unidirectional and only flows from the CAN bus through the receive path of
the transceiver to the CAN protocol controller via the RXD output pin. The receiver is translating the differential
signal from CANH and CANL to a digital output on RXD.
10.4.4 Standby Mode with Wake
This is the low power mode of the device. The CAN driver and main receiver are turned off and bi-directional
CAN communication is not possible. The low power receiver and bus monitor are enabled to allow for RXD Wake
Requests via the CAN bus. A wake up request will be output to RXD (driven low) as shown in Figure 33. The
local CAN protocol microprocessor should monitor RXD for transitions (high to low) and reactivate the device to
normal mode based on the RXD Wake Request. The CAN bus pins are weakly pulled to GND during this mode,
see Figure 32.
10.4.5 Bus Wake via RXD Request (BWRR) in Standby Mode
The TCAN334 with low power standby mode, offers a wake up from the CAN bus mechanism called bus wake
via RXD Request (BWRR) to indicate to a host microprocessor that the bus is active and it should wake up and
return to normal CAN communication.
This device uses the multiple filtered dominant wake-up pattern (WUP) from ISO11898-5 to qualify bus traffic into
a request to wake the host microprocessor. The bus wake request is signaled to the microprocessor by a falling
edge and low corresponding to a “filtered” bus dominant on the RXD terminal (BWRR).
The wake up pattern (WUP) consists of a filtered dominant bus, then a filtered recessive bus time followed by a
second filtered bus time. Once the WUP is detected the device will start issuing wake up requests (BWRR) on
the RXD terminal every time a filtered dominant time is received from the bus. The first filtered dominant initiates
the WUP and the bus monitor waits on a filtered recessive; other bus traffic does not reset the bus monitor. Once
a filtered recessive is received, the bus monitor waits on a filtered dominant and again; other bus traffic does not
reset the bus monitor. Immediately upon receiving of the second filtered dominant, the bus monitor recognizes
the WUP and transitions to BWRR mode. In this mode, RXD is driven low for all dominant bits lasting for longer
than tWK_FILTER. The RXD output during BWRR matches the classical 8-pin CAN devices, such as the
TCANA1040A-Q1 device, that used the single filtered dominant on the bus as the wake up request mechanism
from ISO11898-5.
Copyright © 2015–2019, Texas Instruments Incorporated
23
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
For a dominant or recessive to be considered filtered, the bus must be in that state for more than tWK_FILTER time.
Due to variability in the tWK_FILTER the following scenarios are applicable. Bus state times less than tWK_FILTER(MIN)
are never detected as part of a WUP and thus no BWRR is generated. Bus state times between tWK_FILTER(MIN)
and tWK_FILTER(MAX) may be detected as part of a WUP and a BWRR may be generated. Bus state times more
than tWK_FILTER(MAX) are always detected as part of a WUP and thus a BWRR is always generated.
See Figure 33 for the timing diagram of the WUP. The pattern, tWK_FILTER time used for the WUP and BWRR
prevent noise and bus stuck dominant faults from causing false wake requests. If the device is switched to
normal mode, or an under voltage event occurs on VCC the BWRR will be lost.
Wake Up Pattern (WUP)
Wake Request via RXD
Filtered
Dominant
Filtered
Dominant
Filtered
Recessive
Waiting for
Filtered
Dominant
Waiting for
Filtered
Recessive
Bus
Bus VDiff
≥ tWK_FILTER
≥ tWK_FILTER
≥ tWK_FILTER
≥ tWK_FILTER
RXD
Figure 33. Wake Up Pattern (WUP) and Bus Wake via RXD Request (BWRR)
10.4.6 Shutdown Mode
This is the lowest power mode of all of the devices. The CAN driver and receiver are turned off and bi-directional
CAN communication is not possible. It is not possible to receive a remote wake request via the CAN bus in this
mode. The CAN bus pins are pulled to GND during this mode as shown in Figure 31.
24
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
10.4.7 Driver and Receiver Function Tables
Table 6. Driver Function Table
BUS OUTPUTS(2)
(3)
DEVICE MODE
TXD(1) INPUT
DRIVEN BUS STATE
CANH
CANL
L
H
Z
Z
Z
Z
L
Z
Z
Z
Z
Dominant
Normal
H or Open
Biased Recessive
Biased Recessive
Weak Pull to GND
Weak Pull to GND
Silent
X
X
X
Standby
Shutdown
(1) H = high level, L = low level, X = irrelevant.
(2) H = high level, L = low level, Z = high Z receiver bias.
(3) For Bus state and bias see Figure 31 and Figure 32.
Table 7. Receiver Function Table Normal and Standby Modes
CAN DIFFERENTIAL INPUTS
BUS STATE
DEVICE MODE
RXD PIN(1)
V(ID) = V(CANH) – V(CANL)
V
(ID) ≥ 0.9 V
0.5 V < V(ID) < 0.9 V
(ID) ≤ 0.5 V
(ID) ≥ 1.15 V
0.4 V < V(ID) < 1.15 V
Dominant
?
L
?
Normal or Silent
V
Recessive
Dominant
?
H
V
Standby
See Figure 33
V
(ID) ≤ 0.4 V
Recessive
Recessive
Open
Shutdown
Any
Any
H
H
Open (V(ID) ≈ 0 V)
(1) I = high level, L = low level, ? = indeterminate.
Copyright © 2015–2019, Texas Instruments Incorporated
25
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
11 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
11.1 Application Information
11.1.1 Bus Loading, Length and Number of Nodes
The ISO 11898 standard specifies a data rate up to 1 Mbps, maximum CAN bus cable length of 40 m, maximum
drop line (stub) length of 0.3 m and a maximum of 30 nodes. However, with careful network design, the system
may have longer cables, longer stub lengths, and many more nodes to a bus. Many CAN organizations and
standards have scaled the use of CAN for applications outside the original ISO 11898 standard. They have made
system level trade-offs for data rate, cable length, and parasitic loading of the bus. Examples of some of these
specifications are ARINC825, CANopen, CAN Kingdom, DeviceNet and NMEA200.
A high number of nodes requires a transceiver with high input impedance and wide common mode range such
as the TCAN33x CAN family. ISO 11898-2 specifies the driver differential output with a 60-Ω load (two 120- Ω
termination resistors in parallel) and the differential output must be greater than 1.5 V. The TCAN33x devices are
specified to meet the 1.5-V requirement with a 50-Ω load across a common mode range of –12 V to 12 V
through a 330-Ω coupling network. This network represents the bus loading of 120 TCAN33x transceivers based
on their minimum differential input resistance of 40 kΩ.
For CAN network design, margin must be given for signal loss across the system and cabling, parasitic loadings,
network imbalances, ground offsets and signal integrity, thus a practical maximum number of nodes may be
lower. Bus length may also be extended beyond the original ISO 11898 standard of 40 m by careful system
design and data rate tradeoffs. For example, CANopen network design guidelines allow the network to be up to
1 km with changes in the termination resistance, cabling, number of nodes and data rate.
This flexibility in CAN network design is one of the key strengths of the various extensions and additional
standards that have been built on the original ISO 11898 CAN standard.
11.2 Typical Application
VCC
3
SHDN/
FAULT
5
TCAN33x
VCC
VOUT
VIN
VIN
S / STB
CANH
8
7
CAN Transceiver
3-V Voltage
Regulator
3-V MCU
(e.g. TPSxxxx)
RXD
TXD
RXD
TXD
4
1
CANL
6
Optional:
Terminating
Node
2
GND
Copyright © 2016, Texas Instruments Incorporated
Figure 34. Typical 3.3-V Application
26
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
Typical Application (continued)
11.2.1 Design Requirements
11.2.1.1 CAN Termination
The ISO 11898 standard specifies the interconnect to be a twisted-pair cable (shielded or unshielded) with 120-Ω
characteristic impedance (ZO). Resistors equal to the characteristic impedance of the line should be used to
terminate both ends of the cable to prevent signal reflections. Unterminated drop lines (stubs) connecting nodes
to the bus should be kept as short as possible to minimize signal reflections. The termination may be on the
cable or in a node, but if nodes may be removed from the bus the termination must be carefully placed so that it
is not removed from the bus.
11.2.2 Detailed Design Procedure
Termination is typically a 120-Ω resistor at each end of the bus. If filtering and stabilization of the common mode
voltage of the bus is desired, then split termination may be used (see Figure 8). Split termination uses two 60-Ω
resistors with a capacitor in the middle of these resistors to ground. Split termination improves the
electromagnetic emissions behavior of the network by eliminating fluctuations in the bus common mode voltages
at the start and end of message transmissions.
Care should be taken in the power ratings of the termination resistors used. Typically the worst case condition
would be if the system power supply was shorted across the termination resistance to ground. In most cases the
current flow through the resistor in this condition would be much higher than the transceiver's current limit.
Node n
(with termination)
Node 1
Node 2
Node 3
MCU or DSP
MCU or DSP
MCU or DSP
MCU or DSP
CAN
Controller
CAN
Controller
CAN
Controller
CAN
Controller
CAN Transceiver
RTERM
CAN Transceiver
CAN Transceiver
CAN Transceiver
RTERM
Figure 35. Typical CAN Bus
Copyright © 2015–2019, Texas Instruments Incorporated
27
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
Typical Application (continued)
Standard Termination
Split Termination
CANH
CANH
RTERM/2
CAN
Transceiver
CAN
Transceiver
RTERM
CSPLIT
RTERM/2
CANL
CANL
Figure 36. CAN Bus Termination Concepts
11.2.3 Application Curves
1 Mbps
Temp = 25°C
VCC = 3.3 V
5 Mbps
Temp = 25°C
VCC = 3.3 V
60 Ω Load
60 Ω Load
Figure 37. TXD, CANH/L and RXD Waveforms
Figure 38. TXD, CANH/L and RXD Waveforms
11.3 System Examples
11.3.1 ISO11898 Compliance of TCAN33x Family of 3.3-V CAN Transceivers Introduction
Many users value the low power consumption of operating their CAN transceivers from a 3.3-V supply. However,
some are concerned about the interoperability with 5 V supplied transceivers on the same bus. This report
analyzes this situation to address those concerns.
28
Copyright © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
System Examples (continued)
11.3.2 Differential Signal
CAN is a differential bus where complementary signals are sent over two wires and the voltage difference
between the two wires defines the logical state of the bus. The differential CAN receiver monitors this voltage
difference and outputs the bus state with a single ended logic level output signal.
NOISE MARGIN
900 mV Threshold
RECEIVER DETECTION WINDOW
75% SAMPLE POINT
500 mV Threshold
NOISE MARGIN
Figure 39. Typical Differential Output Waveform
The CAN driver creates the differential voltage between CANH and CANL in the dominant state. The dominant
differential output of the TCAN33x is greater than 1.5 V and less than 3 V across a 60-Ω load as defined by the
ISO11898 standard. These are the same limiting values for 5 V supplied CAN transceivers. The bus termination
resistors drive the recessive bus state and not the CAN driver.
A CAN receiver is required to output a recessive state when less than 500 mV of differential voltage exists on the
bus, and a dominant state when more than 900 mV of differential voltage exists on the bus. The CAN receiver
must do this with common-mode input voltages from –2 V to 7 V. The TCAN33x family receivers meet these
same input specifications as 5 V supplied receivers.
11.3.3 Common-Mode Signal and EMC Performance
A common-mode signal is an average voltage of the two signal wires that the differential receiver rejects. The
common-mode signal comes from the CAN driver, ground noise, and coupled bus noise. Since the bias voltage
of the recessive state of the device is dependent on VCC, any noise present or variation of VCC has an effect on
this bias voltage seen by the bus. The TCAN33x family has the recessive bias voltage set higher than 0.5 x VCC
to match common mode in recessive mode to dominant mode. This results in superior EMC performance.
12 Power Supply Recommendations
To ensure reliable operation at all data rates and supply voltages, each supply should be decoupled with a 100-
nF ceramic capacitor located as close to the VCC supply pins as possible. The TPS76333 is a linear voltage
regulator suitable for the 3.3 V supply.
Copyright © 2015–2019, Texas Instruments Incorporated
29
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
13 Layout
13.1 Layout Guidelines
TCAN33x family of devices incorporates integrated IEC 61000-4-2 ESD protection. Should the system requires
additional protection against ESD, EFT or surge, additional external protection and filtering circuitry may be
needed.
In order for the PCB design to be successful, start with design of the protection and filtering circuitry. Because
ESD and EFT transients have a wide frequency bandwidth from approximately 3 MHz to 3 GHz, high frequency
layout techniques must be applied during PCB design.
Design the bus protection components in the direction of the signal path. Do not force the transient current to
divert from the signal path to reach the protection device. Below is a list of layout recommendations when
designing a CAN transceiver into an application.
•
Transient Protection on CANH and CANL: Transient Voltage Suppression (TVS) and capacitors (D1, C5 and
C7 shown in Figure 40) can be used for additional system level protection. These devices must be placed as
close to the connector as possible. This prevents the transient energy and noise from penetrating into other
nets on the board.
•
Bus Termination on CANH and CANL: Figure 40 shows split termination where the termination is split into two
resistors, R5 and R6, with the center or split tap of the termination connected to ground through capacitor C6.
Split termination provides common mode filtering for the bus. When termination is placed on the board
instead of directly on the bus, care must be taken to ensure the terminating node is not removed from the
bus, as this causes signal integrity issues if the bus is not properly terminated on both ends.
•
•
•
•
•
•
Decoupling Capacitors on VCC: Bypass and bulk capacitors must be placed as close as possible to the supply
pins of transceiver (examples are C2 and C3).
Ground and power connections: Use at least two vias for VCC and ground connections of bypass capacitors
and protection devices to minimize trace and via inductance.
Digital inputs and outputs: To limit current of digital lines, serial resistors may be used. Examples are R1, R2,
R3 and R4.
Filtering noise on digital inputs and outputs: To filter noise on the digital I/O lines, a capacitor may be used
close to the input side of the I/O as shown by C1, C8 and C4.
Fault Output Pin (TCAN337 only): Because the FAULT output pin is an open drain output, an external pullup
resistor is required to pull the pin voltage high for normal operation (R7).
TXD input pin: If an open-drain host processor is used to drive the TXD pin of the device, an external pullup
resistor between 1 kΩ and 10 kΩ must be used to help drive the recessive input state of the device (weak
internal pullup resistor).
30
版权 © 2015–2019, Texas Instruments Incorporated
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
www.ti.com.cn
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
13.2 Layout Example
1
8
TXD
S/STB
R3
R1
GND
VCC
C4
2
3
4
7
R5
U1
TCAN33x
C6
6
R6
5
RXD
R2
SHDN
R4
C8
R7
VCC
FAULT
Figure 40. Layout Example
版权 © 2015–2019, Texas Instruments Incorporated
31
TCAN330, TCAN332, TCAN334, TCAN337
TCAN330G, TCAN332G, TCAN334G, TCAN337G
ZHCSEG6E –DECEMBER 2015–REVISED DECEMBER 2019
www.ti.com.cn
14 器件和文档支持
14.1 相关链接
下表列出了快速访问链接。类别包括技术文档、支持与社区资源、工具和软件,以及申请样片或购买产品的快速链
接。
表 8. 相关链接
器件
产品文件夹
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
样片与购买
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
技术文档
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
工具与软件
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
支持和社区
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
请单击此处
TCAN330
TCAN332
TCAN334
TCAN337
TCAN330G
TCAN332G
TCAN334G
TCAN337G
14.2 支持资源
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
14.3 商标
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
14.4 静电放电警告
这些装置包含有限的内置 ESD 保护。 存储或装卸时,应将导线一起截短或将装置放置于导电泡棉中,以防止 MOS 门极遭受静电损
伤。
14.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
15 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知,且
不会对此文档进行修订。如需获取此数据表的浏览器版本,请查阅左侧的导航栏。
32
版权 © 2015–2019, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TCAN330D
TCAN330DCNR
TCAN330DCNT
TCAN330DR
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOT-23
SOT-23
SOIC
D
DCN
DCN
D
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
TC330
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
75 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
75 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
75 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
75 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
330
330
TC330
TC330
330
TCAN330GD
SOIC
D
TCAN330GDCNR
TCAN330GDCNT
TCAN330GDR
TCAN332D
SOT-23
SOT-23
SOIC
DCN
DCN
D
330
TC330
TC332
332
SOIC
D
TCAN332DCNR
TCAN332DCNT
TCAN332DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
332
TC332
TC332
332
TCAN332GD
SOIC
D
TCAN332GDCNR
TCAN332GDCNT
TCAN332GDR
TCAN334D
SOT-23
SOT-23
SOIC
DCN
DCN
D
332
TC332
TC334
334
SOIC
D
TCAN334DCNR
TCAN334DCNT
TCAN334DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
334
TC334
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TCAN334GD
TCAN334GDCNR
TCAN334GDCNT
TCAN334GDR
TCAN337D
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOT-23
SOT-23
SOIC
D
DCN
DCN
D
8
8
8
8
8
8
8
8
8
8
8
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
TC334
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
75 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
75 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
2500 RoHS & Green
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
334
334
TC334
TC337
337
SOIC
D
TCAN337DCNR
TCAN337DCNT
TCAN337DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
337
TC337
TC337
337
TCAN337GD
SOIC
D
TCAN337GDCNR
TCAN337GDCNT
TCAN337GDR
SOT-23
SOT-23
SOIC
DCN
DCN
D
337
TC337
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TCAN330DCNR
TCAN330DCNT
TCAN330DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
3000
250
180.0
180.0
330.0
180.0
180.0
330.0
180.0
180.0
330.0
180.0
180.0
330.0
180.0
180.0
330.0
180.0
180.0
330.0
8.4
8.4
3.23
3.23
6.4
3.17
3.17
5.2
1.37
1.37
2.1
4.0
4.0
8.0
4.0
4.0
8.0
4.0
4.0
8.0
4.0
4.0
8.0
4.0
4.0
8.0
4.0
4.0
8.0
8.0
8.0
Q3
Q3
Q1
Q3
Q3
Q1
Q3
Q3
Q1
Q3
Q3
Q1
Q3
Q3
Q1
Q3
Q3
Q1
2500
3000
250
12.4
8.4
12.0
8.0
TCAN330GDCNR
TCAN330GDCNT
TCAN330GDR
TCAN332DCNR
TCAN332DCNT
TCAN332DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
3.23
3.23
6.4
3.17
3.17
5.2
1.37
1.37
2.1
8.4
8.0
2500
3000
250
12.4
8.4
12.0
8.0
SOT-23
SOT-23
SOIC
DCN
DCN
D
3.23
3.23
6.4
3.17
3.17
5.2
1.37
1.37
2.1
8.4
8.0
2500
3000
250
12.4
8.4
12.0
8.0
TCAN332GDCNR
TCAN332GDCNT
TCAN332GDR
TCAN334DCNR
TCAN334DCNT
TCAN334DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
3.23
3.23
6.4
3.17
3.17
5.2
1.37
1.37
2.1
8.4
8.0
2500
3000
250
12.4
8.4
12.0
8.0
SOT-23
SOT-23
SOIC
DCN
DCN
D
3.23
3.23
6.4
3.17
3.17
5.2
1.37
1.37
2.1
8.4
8.0
2500
3000
250
12.4
8.4
12.0
8.0
TCAN334GDCNR
TCAN334GDCNT
TCAN334GDR
SOT-23
SOT-23
SOIC
DCN
DCN
D
3.23
3.23
6.4
3.17
3.17
5.2
1.37
1.37
2.1
8.4
8.0
2500
12.4
12.0
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TCAN337DCNR
TCAN337DCNT
TCAN337DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
8
8
8
8
8
8
3000
250
180.0
180.0
330.0
180.0
180.0
330.0
8.4
8.4
3.23
3.23
6.4
3.17
3.17
5.2
1.37
1.37
2.1
4.0
4.0
8.0
4.0
4.0
8.0
8.0
8.0
Q3
Q3
Q1
Q3
Q3
Q1
2500
3000
250
12.4
8.4
12.0
8.0
TCAN337GDCNR
TCAN337GDCNT
TCAN337GDR
SOT-23
SOT-23
SOIC
DCN
DCN
D
3.23
3.23
6.4
3.17
3.17
5.2
1.37
1.37
2.1
8.4
8.0
2500
12.4
12.0
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TCAN330DCNR
TCAN330DCNT
TCAN330DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
8
8
8
8
8
8
8
8
8
8
8
3000
250
202.0
202.0
340.5
202.0
202.0
340.5
202.0
202.0
340.5
202.0
202.0
201.0
201.0
336.1
201.0
201.0
336.1
201.0
201.0
336.1
201.0
201.0
28.0
28.0
25.0
28.0
28.0
25.0
28.0
28.0
25.0
28.0
28.0
2500
3000
250
TCAN330GDCNR
TCAN330GDCNT
TCAN330GDR
TCAN332DCNR
TCAN332DCNT
TCAN332DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
2500
3000
250
SOT-23
SOT-23
SOIC
DCN
DCN
D
2500
3000
250
TCAN332GDCNR
TCAN332GDCNT
SOT-23
SOT-23
DCN
DCN
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TCAN332GDR
TCAN334DCNR
TCAN334DCNT
TCAN334DR
SOIC
SOT-23
SOT-23
SOIC
D
8
8
8
8
8
8
8
8
8
8
8
8
8
2500
3000
250
340.5
202.0
202.0
340.5
202.0
202.0
340.5
202.0
202.0
340.5
202.0
202.0
340.5
336.1
201.0
201.0
336.1
201.0
201.0
336.1
201.0
201.0
336.1
201.0
201.0
336.1
25.0
28.0
28.0
25.0
28.0
28.0
25.0
28.0
28.0
25.0
28.0
28.0
25.0
DCN
DCN
D
2500
3000
250
TCAN334GDCNR
TCAN334GDCNT
TCAN334GDR
TCAN337DCNR
TCAN337DCNT
TCAN337DR
SOT-23
SOT-23
SOIC
DCN
DCN
D
2500
3000
250
SOT-23
SOT-23
SOIC
DCN
DCN
D
2500
3000
250
TCAN337GDCNR
TCAN337GDCNT
TCAN337GDR
SOT-23
SOT-23
SOIC
DCN
DCN
D
2500
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
TUBE
*All dimensions are nominal
Device
Package Name Package Type
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
TCAN330D
TCAN330GD
TCAN332D
TCAN332GD
TCAN334D
TCAN334GD
TCAN337D
TCAN337GD
D
D
D
D
D
D
D
D
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
SOIC
8
8
8
8
8
8
8
8
75
75
75
75
75
75
75
75
507
507
507
507
507
507
507
507
8
8
8
8
8
8
8
8
3940
3940
3940
3940
3940
3940
3940
3940
4.32
4.32
4.32
4.32
4.32
4.32
4.32
4.32
Pack Materials-Page 4
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022,德州仪器 (TI) 公司
相关型号:
©2020 ICPDF网 联系我们和版权申明